Moment & Shear Strength Design of Rectangular RC Slab According ACI318M-08
Project :- ESPAC Factory - Dammam Designed by:- M. Abu Shady
Building :- TANK WALL - BLG. 23 Checked by:- M. Abu Shady
Element:- ROOF Date:- 02-Oct-19
Location:-
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
General Input :- mail to [email protected]
Moment Mx Input
Width b 1000 mm Dia 12 mm
Depth h 300 mm Es 200000 N/mm2
cover 25 mm εc 0.003 mm
d' 25 mm εy 0.0021 mm
fy 420 N/mm2 Ec 25743 N/mm2 ACI 8.5.1
fc' 30 N/mm2
Mu 230 KN.m
Shear & Torsion Input
Vu 0 KN S st spacing 100 mm
Tu 0 KN.m nst 1 legs
Nu 0 KN Comp. Case Env. For Environmental Structures
fyt 420 N/mm2 α st Deg. 90o Deg.
d 269 mm
a- Major Moment ( Mx) Design:-
finding ρ max ACI 10.3.3
β1 0.84 ACI 10.2.7.3
ρp 0.02985 ACI B.8.4.2
ρmin 0.00180 ACI 10.5.1
ρmax 0.02239 ACI 10.3.5
finding balanced moment strength
Cb 158 mm
ab 132 mm
amax 99 mm ACI 10.3.3
Cmax 119 mm
Φ 0.9 ACI 9.3.2.1 Tension-controlled sections
ΦMnbal 499.4 KN.m Tension RFT. Only
Rectangular Section with Tension & Compression RFT.
M'u = 0.0 KN.m
ρ'req 0.00000 Ru 3.53168
ρreq 0.00909
A's req 0 mm2 0 Φ 12
Page 1 of 11
Moment & Shear Strength Design of Rectangular RC Slab According ACI318M-08
Project :- ESPAC Factory - Dammam Designed by:- M. Abu Shady
Building :- TANK WALL - BLG. 23 Checked by:- M. Abu Shady
Element:- ROOF Date:- 02-Oct-19
Location:-
M. Abushady:
This sheet created by M. Abushady
As req 2445 16 Φ 14 for comments & notes on it. Send an e-
mm2 mail to [email protected]
A's act 0 mm2 0 Φ 12 TOP
As act 2464 mm2 16 Φ 14
Page 2 of 11
Moment & Shear Strength Design of Rectangular RC Slab According ACI318M-08
Project :- ESPAC Factory - Dammam Designed by:- M. Abu Shady
Building :- TANK WALL - BLG. 23 Checked by:- M. Abu Shady
Element:- ROOF Date:- 02-Oct-19
Location:-
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
check Compression Steel yeilds mail to [email protected]
a 40.6 mm
C 48.6 mm
εs 0.0136 εs>εy
εs' 0.0000
Cconc 1034880 N
Cst 0 N
ΦMn 231.6 KN.m
b- Major Shear ( V2 ) Design :-
Finding Vc ACI 11.3
Φ shear 0.85 ACI 9.3.2.3 & ACI 9.3.4.a
Vc 250.5 KN ACI 11.2.1.1 & ACI 11.2.2.3
Vs max 972.4 KN ACI 11.4.7.9
ΦVn 1039.5 KN ACI 11.1.1
Av min 83.3 mm 2
ACI 11.4.6.3
Vs -212.9 KN ACI 11.1.1
Av 0.0 mm2 ACI 11.4.7.4
c- Torsion design:-
Acp = Ag 300000 mm2
Aoh 237500 mm2
Ao 201875 mm2 ACI 11.5.1
Pcp 2600 mm
Ph 2400 mm
Threshold Torsion ACI 11.5.1
Tcr 63 KN.m ACI 11.5.1.c
Tneglected 13.3 KN.m ACI 11.5.1.c Torsion is Neglected Tu<Tneglected
Factored Torsion Moment ACI 11.5.3.1
= 0.000 < = 3.864 ACI 11.5.3.1.a
Page 3 of 11
Moment & Shear Strength Design of Rectangular RC Slab According ACI318M-08
Project :- ESPAC Factory - Dammam Designed by:- M. Abu Shady
Building :- TANK WALL - BLG. 23 Checked by:- M. Abu Shady
Element:- ROOF Date:- 02-Oct-19
Location:-
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
mail to [email protected]
Page 4 of 11
Moment & Shear Strength Design of Rectangular RC Slab According ACI318M-08
Project :- ESPAC Factory - Dammam Designed by:- M. Abu Shady
Building :- TANK WALL - BLG. 23 Checked by:- M. Abu Shady
Element:- ROOF Date:- 02-Oct-19
Location:-
M. Abushady:
This sheet created by M. Abushady
Finding Torsion Stirrups At for comments & notes on it. Send an e-
mail to [email protected]
θ 45o Deg. ACI 11.5.3.6.a
At min 42 mm2 ACI 11.5.5.3
At 0 mm2 ACI 11.5.3.6
A stirrup total 0 mm2 ACI 11.5.5.2
A stirrup total/Leg 0.0 mm2 0 Φ 12 Ordinary Stirrups
Finding Torsion Longitudinal RFT Al
Al min 1643.2 mm2 ACI 11.5.5.3
Al 0.0 mm2 ACI 11.5.7 0 Φ 32
Beam Reinforcement details
25
0 Φ 12
0Φ12@100mm
300
1 branches - Ordinary Stirrups
0 Φ 32 SIDE BAR E.F
16 Φ 14
1000
Page 5 of 11
According ACI318M-08
Rev04
M. Abu Shady
M. Abu Shady
02-Oct-19
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
mail to [email protected]
For Environmental Structures
Tension-controlled sections
Tension RFT. Only
Page 6 of 11
According ACI318M-08
Rev04
M. Abu Shady
M. Abu Shady
02-Oct-19
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
mail to [email protected]
Page 7 of 11
According ACI318M-08
Rev04
M. Abu Shady
M. Abu Shady
02-Oct-19
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
mail to [email protected]
Torsion is Neglected Tu<Tneglected
ACI 11.5.3.1.a
Page 8 of 11
According ACI318M-08
Rev04
M. Abu Shady
M. Abu Shady
02-Oct-19
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
mail to [email protected]
Page 9 of 11
According ACI318M-08
Rev04
M. Abu Shady
M. Abu Shady
02-Oct-19
M. Abushady:
This sheet created by M. Abushady
for comments & notes on it. Send an e-
mail to [email protected]
Page 10 of 11
DIA (mm) Area (mm2) Case Element Type
6 29 E For Seismic Cases Beam
8 51 G For Non-seismic Cases Slab
10 79 Env. For Environmental Structures
12 114
14 154
16 201
18 255
20 314
22 380
25 491
32 804
