Preliminary TTP223-BA6

1 KEY TOUCH PAD DETECTOR IC

GENERAL DESCRIPTION
The TTP223-BA6 is a touch pad detector IC which offers 1 touch key. The touching detection
IC is designed for replacing traditional direct button key with diverse pad size. Low power
consumption and wide operating voltage are the contact key features for DC or AC application.

FEATURES
ƒ Operating voltage 2.0V~5.5V
ƒ Operating current @VDD=3V, no load
ƒ At low power mode typical 1.5uA, maximum 3.0uA
ƒ The response time max 220mS at low power mode @VDD=3V
ƒ Sensitivity can adjust by the capacitance(0~50pF) outside
ƒ Stable touching detection of human body for replacing traditional direct switch key
ƒ Provides Low Power mode
ƒ Provides direct mode、toggle mode by pad option(TOG pin)
Q pin is CMOS output
ƒ All output modes can be selected active high or active low by pad option(AHLB pin)
ƒ After power-on have about 0.5sec stable-time, during the time do not touch the key pad,
And the function is disabled
ƒ Auto calibration for life
At low power mode the re-calibration period is about 4.0sec normally,
When key detected touch and released touch, the auto re-calibration will be redoing after
about 16sec from releasing key

APPLICATION
ƒ Wide consumer products
ƒ Button key replacement

08’/08/15 Page 1 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/

 Preliminary TTP223-BA6
BLOCK DIAGRAM

Sensor oscillator Sensor &

I circuit Reference
detecting circuit Output Q
mode
&
driver
circuit
Touch detecting
Timing counter circuit

TOG
System oscillator Key-on & timing
circuit control AHLB

PACKAGE LIST
Package Type SOT-23-6L
TTP223-BA6 PACKAGE CONFIGURATION
AHLB
TOG

VDD
6

223B
Lot No.(Latter 5 digit)
1

3
VSS
Q

PAD DESCRIPTION
Pad No. Pad Name I/O Type Pad Description
1 Q O CMOS output pin
2 VSS P Negative power supply, ground
3 I I/O Input sensor port
4 AHLB I-PL Output active high or low selection,
1=>Active low; 0(Default)=>Active high
5 VDD P Positive power supply
6 TOG I-PL Output type option pin,
1=>Toggle mode; 0(Default)=>Direct mode
Pin Type
I CMOS input only
O CMOS push-pull output
I/O CMOS I/O
I-PL CMOS input and pull-low resister
P Power / Ground
08’/08/15 Page 2 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com

 Preliminary TTP223-BA6
ELECTRICAL CHARACTERISTICS
‧Absolute Maximum Ratings
Parameter Symbol Conditions Value Unit
Operating Temperature TOP ─ -20 ~ +70 ℃
Storage Temperature TSTG ─ -50 ~ +125 ℃
Power Supply Voltage VDD Ta=25°C VSS-0.3 ~ VSS+5.5 V
Input Voltage VIN Ta=25°C VSS-0.3 ~ VDD+0.3 V
Human Body Mode ESD ─ 4 KV
Note：VSS symbolizes for system ground

‧DC/AC Characteristics：(Test condition at room temperature=25℃)

Parameter Symbol Test Condition Min. Typ. Max. Unit

Operating Voltage VDD 2.0 3 5.5 V
System oscillator FFAST VDD=3V - 512K - Hz
FLOW 16K
Sensor oscillator FSEN VDD=3V no load - 1M - Hz
Operating Current IOP VDD=3V - 1.5 3.0
at low power mode uA
and output no load
Input Ports VIL Input Low Voltage 0 - 0.2 VDD
Input Ports VIH Input High Voltage 0.8 - 1.0 VDD
Output Port Sink Current IOL VDD=3V, VOL=0.6V - 8 - mA
Output Port Source Current IOH VDD=3V, VOH=2.4V - -4 - mA
Output Response Time TR VDD=3V, At fast mode 60 mS
VDD=3V, At low power mode 220
Input Pin Pull-low Resistor RPL VDD=3V, 28K ohm
(TOG, AHLB)

08’/08/15 Page 3 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/

 Preliminary TTP223-BA6
FUNCTION DESCRIPTION
1. Sensitivity adjustment
The total loading of electrode size and capacitance of connecting line on PCB can affect the
sensitivity. So the sensitivity adjustment must according to the practical application on PCB. The
TTP223-BA6 offers some methods for adjusting the sensitivity outside.
1-1 by the electrode size
Under other conditions are fixed. Using a larger electrode size can increase sensitivity. Otherwise it
can decrease sensitivity. But the electrode size must use in the effective scope.
1-2 by the panel thickness
Under other conditions are fixed. Using a thinner panel can increase sensitivity. Otherwise it can
decrease sensitivity. But the panel thickness must be below the maximum value.
1-3 by the value of Cs (please see the down figure)
Under other conditions are fixed. When do not use the Cs to VSS, the sensitivity is most sensitive.
When adding the values of Cs will reduce sensitivity in the useful range (0≦Cs≦50pF).

VDD
5
ELECTRODE VDD
3 1
I Q
6
TOG
4
AHLB
Cs
VSS
2

2. Output mode
The TTP223-BA6 has direct mode active high or low by AHLB pad option. And has toggle mode
by TOG pad option. Pad Q is CMOS output.

TOG AHLB Pad Q option features

0 0 Direct mode,
CMOS active high output
0 1 Direct mode,
CMOS active low output
1 0 Toggle mode,
Power on state=0
1 1 Toggle mode,
Power on state=1

08’/08/15 Page 4 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/

 Preliminary TTP223-BA6
3. Low power mode
The TTP223-BA6 is Low Power mode. It will be saving power. When detecting key touch, it will
switch to Fast mode. Until the key touch is released and will keep a time about 12sec. Then it
returns to Low Power mode.
The states and timing please see below figure.
Low Power Fast mode Low Power Fast mode Low Power
mode timing timing mode timing timing mode timing

VDD
I VSS
~160ms ~20ms ~160ms ~20ms ABOUT 12SEC ~160ms
POSSIBLE KEY TOUCH KEY RELEASE KEY TOUCH KEY RELEASE
(NOT REALLY TOUCH)
VDD
Q
VSS

Low Power Mode

4. Option pin
For power saving concern and package bonding option consideration, all the feature option pins
with latch type design and initial states are 0 or 1 as power on. If those pins are forced to VDD or
VSS, the states will be changed to 1 or 0 without any current leakage to conflict the power saving
issue.
Feature option pins Initial state by Power on
AHLB 0
TOG 0

08’/08/15 Page 5 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/

 Preliminary TTP223-BA6
APPLICATION CIRCUIT
VCC +2.0 ~ +5.5V
Voltage Regulator
Vin Vout
VSS
Ci Co
4.7uF 4.7uF
See P.S. : 6

TTP223-BA6 SOT-23-6L

1Q TOG 6

2 VSS VDD 5

3I AHLB 4
104
Cs
Sense Pad C1

PS：1. On PCB, the length of lines from touch pad to IC pin shorter is better.
And the lines do not parallel and cross with other lines.
2. The power supply must be stable. If the supply voltage drift or shift quickly, maybe causing
sensitivity anomalies or false detections.
3. The material of panel covering on the PCB can not include the metal or the electric element.
The paints on the surfaces are the same.
4. The capacitance Cs can be used to adjust the sensitivity. The value of Cs use smaller, then
the sensitivity will be better. The sensitivity adjustment must according to the practical
application on PCB. The range of Cs value is 0~50pF.
5. The C1 capacitor must be used between VDD and VSS; and should be routed with very short
tracks to the device’s VDD and VSS pins (TTP223-BA6) .
6. The value of capacitors can be used by the real application for Ci and Co capacitors.

08’/08/15 Page 6 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/

 Preliminary TTP223-BA6
Package Type: SOT-23-6L

Package Outline Dimension

08’/08/15 Page 7 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/

 Preliminary TTP223-BA6
ORDER INFORMATION
a. Package form: TTP223-BA6

REVISE HISTORY
1. 2008/08/15
-Original version：V1.0

08’/08/15 Page 8 of 8 Ver : 1.0

Free Datasheet http://www.datasheet4u.com/