Scribd
Upload
85 views

Flexural Testing Machine

This document specifies the requirements for a flexure testing machine, including: - Capabilities of testing fiber reinforced and normal concrete beams under three-point and four-point loading configurations - Specifications for the testing frame, including load capacity, actuator capabilities, and ability to adjust support distances - Requirements for a computerized control unit and software for automated testing - Accessories for flexural testing of beams and slabs of various sizes - Terms for installation, training, maintenance, and payments

Uploaded by

sirfmein
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views

Flexural Testing Machine

This document specifies the requirements for a flexure testing machine, including: - Capabilities of testing fiber reinforced and normal concrete beams under three-point and four-point loading configurations - Specifications for the testing frame, including load capacity, actuator capabilities, and ability to adjust support distances - Requirements for a computerized control unit and software for automated testing - Accessories for flexural testing of beams and slabs of various sizes - Terms for installation, training, maintenance, and payments

Uploaded by

sirfmein
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ITEM: Flexure Testing Machine

A. Specifications:
Capable of testing fibre reinforced concrete beams and normal concrete beams. Following components
are required for the Flexural testing machine

1. Flexure Testing Frame:


a) Suitable structure with safety arrangements
b) Working Range: 3kN to 300kN
c) The frame should have a single acting hydraulic cylinder at its center
d) The actuator should have a suitable transducer capable of measuring load in range of 1% to
100% of the full-scale with a resolution of 0.1 kN and an accuracy of ±1% or better
e) The actuator should have a suitable transducer capable of measuring displacements of up to
1000 mm at 0.001 mm resolution with an accuracy of ±0.5% or better
f) Capable of executing three-point and four-point flexure tests
g) Loading rollers distances: Adjustable from 133 mm to 500 mm or higher over a suitable scale
h) Support rollers distances: Adjustable from 400 mm to 1500 mm or higher over a suitable scale
i) Minimum vertical clearance: 400 mm
j) Maximum travel of ram should be equal to 100 mm with suitable travel limit switch The frame
should be capable of testing beam specimen of 0.5 to 1.5 m length or longer

2. Computerized control unit:


Comprising of a PC interface loaded with an interactive software for exercising fully automatic
load, displacement and strain controlled testing of specimen via appropriate hardware and
capable of storing, analyzing and presenting key test data through the software GUI.

Accessories:

1. Accessories for the flexural testing of fiber reinforced concrete

Auxiliary testing frame capable of holding beam specimen of following sizes:

a) 100 mm × 100 mm × 500 mm.


b) 150 mm × 150 mm × 700 mm .
c) Two displacement measuring transducers with working range of 0 to 10 mm and a
resolution of 0.001 mm at an accuracy of ±1% or better .
d) Conforming to BS EN 14488-3: 2006, ASTM C1609.

2. Accessories for the testing of flexural toughness of fiber reinforced concrete


a) Lower support frame and upper loading element for slab of 800 mm diameter and 75 mm
thickness.
b) Displacement transducers with working range of 0 to 50 mm travel and a resolution of 0.01
mm at an accuracy of ±1% or better.
c) Conforming to ASTM C 1550-12a.
B. T&C for Installations
1. In case of any damage to equipment and supplies during carriage from the origin of equipment to
the installation site, the supplier must replace it with new equipment immediately at his own cost.
2. The supplier is required to carry out the installation within one month of arrival of materials at
the BIT MESRA site of installation.

C. Training Requirements
BIT MESRA will not bear any training expenditure. Adequate training to the nominated persons of BIT
MESRA at their cost.

D. T&C for Maintainance


AMC Required

E. Vendors List

1. Aimil Ltd. 2. Hydraulic & Engineering Instruments


Naimex House B-59/4 , Naraina Industrial Area, Phase-2,
A-8, Mohan Co-operative New Delhi -110028
Industrial Estate, Phone:+91-11-41418424
Mathura Road, +91-11-47553820
New Delhi - 110 044
Phone: . 011-30810200 Mobile : +91 8826898490
Email : [email protected] Email: [email protected]

3. Qualitest 4. Zeal International


2/F, Kalpataru Synergy, Santacruz East, Mumbai, Netaji Subhash Marg Daryaganj
India New Delhi - 110002 INDIA
Tel : +91 22 6169 5990 Phone: +91-11-23276114
Fax : +91 22 6169 5999 +91-11-23244474
Email: [email protected] +91-11-23250281
+91-11-23278846
Email: [email protected]

F. T&C for Payments


80% payment along with Purchase order, 20% after installation and training

You might also like