E9000 Exam Questions
E9000 Exam Questions
True
False
True
False
True
False
False
management. (? )
A. Turbo Boost
B. Hyper-Threading
C. Multi-core
D. SMP
indicate? ( )
In which VLAN setting method, you need to set the VLAN again when the host
is changed to another port? ( )
A. By MAC
B. By IP subnet
C. By port
D. All above
Typically, power cables between PDUs and PDFs are provided by
A. 1 mm2
B. 6 mm2
C. 16 mm2
D. 2.5 mm2
When four CH121s are installed in the E9000, what are the
installation slots? ( )
B. 1, 2, 3, and 4
C. 1, 2, 9, and 10
D. 7, 8, 15, and 16
A. A smart link group cannot detect the unidirectional link fault of the master and slave links
B. A smart link group can have only one pair of master and slave ports.
C. The master and slave ports of the smart link group can forward traffic from multiple VLANs,
B. 10GE2/17/1</p>
C. VlanIf
does it indicate? ( )
B. Critical alarm
D. Major alarm
A. Any switch module can provide one GE port for communicating with MM910s, providing
B. Two MM910s work in active/standby mode. There are heartbeat monitoring signals and
D. Each MM910 provides I2C buses for fan and PSU management.
On the PSU & Fan page, you can view the installation status and
health status for all fan modules. If the server operates properly,
C. Fan 8 to fan 14
D. Fan 1 to fan 7
A. The E9000 chassis supports cascading when management network ports on the MM910s
are used.
B. Cascading ports are used only when multiple chassis are cascaded.
C. The MM910 provides only one management network port and one cascading network port.
D. The E9000 chassis does not support cascading when management network ports on the
hardware? (? )
A. SNMP
B. IPMI
C. RAID
D. SCSI
Trunking? ( )
A. When an error is detected on N_Port Trunking, the HBA needs to register again.
B. ISL Trunking applies only when the CX210 connects to the Brocade switch and a new
license is required.
C. When an error is detected on ISL Trunking, the HBA needs to register again.
D. When an error is detected, the service interruption time of ISL Trunking is smaller than that
of N_Port Trunking.
(1). Place the removed LCD in an ESD bag. (2). Use the Phillips
(3). Pull the LCD out of the chassis horizontally. (4). Use the
(5). Insert a new LCD into the chassis horizontally. (6). Determine
A. (4)(3)(1)(6)(5)(2)
B. (6)(4)(3)(1)(5)(2)
C. (3)(4)(1)(5)(6)(2)
D. (6)(3)(1)(5)(4)(2)
Multi
A. CX610
B. CX310
C. CX110
D. CX311
A. FAT32
B. FAT16
C. NTFS
D. EXT3
A. Fan module
B. Hard disk
C. Mainboard
D. PSU
A. RAID
B. DAS
C. NAS
D. SAN
A. Switch module
B. Fan module
C. MM
D. Compute node
B. CX912
C. CX911
D. CX915
module support? ( )
B. Over SOL
A. RISC
B. EPIC
C. CISC
A. Solaris
B. AIX
C. HP-UN
D. Windows 7
WebUI? ( )
C. MM910 SEL
modules? ( )
C. Create stack ports and add physical member ports to stack ports.
C. Use the BMC that is logged in to over the local serial port.
A. Dynamic LACP
B. Manual
C. Static LACP
A. Computing resource
B. Storage resource
C. Network resource
D. Application resource
Which descriptions are true about FC network connection of
CX311s? ( )
A. When the CX311s directly connect to a FC switch, it is recommended that each CX311
B. When CX311s directly connect to FC storage devices with two storage controllers, it is
C. When the CX311s directly connect to an FC storage device, configure zones based on ports.
D. The CX311s connect to multiple FC links to increase link bandwidth and reliability.
A. Two E9000 chassis with the power consumption of 10,000 W per chassis and configured
B. Three E9000 chassis with the power consumption of 6000 W per chassis and configured
C. Two E9000 chassis with the power consumption of 6000 W per chassis and configured with
D. Three E9000 chassis with the power consumption of 6000 W per chassis and configured
A. CX310
B. CX911
C. CX116
D. CX110