0% found this document useful (0 votes)
97 views3 pages

Toe Stability Check - SLS: 3.0 M Deep TRENCH & SHAFT LEE 17/5/2019 Nus E7

This document contains calculations to check the stability of a trench and shaft excavation against toe failure. It analyzes the active and passive pressures on the wall considering soil properties, groundwater levels, surcharge loads, and calculates the bending moment on the wall. The results show that the passive resistance moment plus the wall capacity exceeds the active loading moment, indicating acceptable stability.

Uploaded by

ThaungMyint
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
97 views3 pages

Toe Stability Check - SLS: 3.0 M Deep TRENCH & SHAFT LEE 17/5/2019 Nus E7

This document contains calculations to check the stability of a trench and shaft excavation against toe failure. It analyzes the active and passive pressures on the wall considering soil properties, groundwater levels, surcharge loads, and calculates the bending moment on the wall. The results show that the passive resistance moment plus the wall capacity exceeds the active loading moment, indicating acceptable stability.

Uploaded by

ThaungMyint
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

TOE STABILITY CHECK_SLS

Project: NUS E7 Designer: LEE


Section: 3.0 m deep TRENCH & SHAFT Date: 17/5/2019
Borelog: BH-01 Overburden Calculations on Active Pressure
σv'
Unit σv (kPa
Trench top Level = 125 mRL Soil Type top bottom Weight (kPa) ) last strut
Water Level on Active Side = 125 mRL FILL 125.0 124.1 18 16.2 7.2
Water level on Passive Side = 122 mRL F2 124.1 124.1 19 16.2 0 h1
a x1
Lowest Strut Level = 124.1 mRL 124.1 124.1 0 16.2 0
mRL
P1
Excavation Level = 122
Wall Toe Level = 120 mRL h
Mobilization Factors for Drained = 1
Mobilization Factors for Undrained = 1
Surcharge = 10 kPa b
Water specific weight = 10 kN/m3

Active Pressures
Level (mRL) Soil Parameters Mobilised Parameters Water Over burden Horizontal Stresses Active Forces Moment
botto Drained/ Unit cu c' cu Top u Bot u cw/cu Top σv or Bot σv or Active- Active-Bot Ma
Soil Type top m Undrained Weight (kPa) (kPa) φ' (o) (kPa) c' (kPa) φ' (o) (kPa) (kPa) or cw/c' Ka σv' (kPa) σv' (kPa) Top (kPa) (kPa) P1 (kN/m) x1 (m) (kNm/m)
FILL 124.1 123.5 Drained 18 0 1 30 0 1 30 9.00 15.00 0.50 0.33 7.2 12.0 13.5 21.1 10.4 0.32 3.3
G(V),N=100 123.5 120.0 Drained 20 0 10 35 0 10 35 15.00 50.00 0.50 0.27 12.0 47.0 8.7 53.2 108.3 2.77 300.0
Total Active Moment = 303.4 kNm/m

Passive Pressures
Level (mRL) Soil Parameters Mobilised Parameters Water Over burden Horizontal Stresses Passive Forces Moment

botto Drained/ Unit cu c' cu Top u Bot u cw/cu Top sv or Bot sv or Passive- Passive- Mp
Soil Type top m Undrained Weight (kPa) (kPa) φ' (o) (kPa) c' (kPa) φ' (o) (kPa) (kPa) or cw/c' Kp sv' (kPa) sv' (kPa) Top (kPa) Bot (kPa) P1 (kN/m) x1 (m) (kNm/m)
G(VI),N=100 122 120.0 Drained 20 0 10 35 0 10 35.00 0.00 20.00 0.50 3.69 0.0 20.0 12.2 106.1 118.3 3.36 398.0
Total Passive Moment = 398.0 kNm/m
Wall Bending Moment Capacity = 45 kNm/m
Check: (Mp + Mw) / Ma = 1.46 > 1.0 = > OK!
TOE STABILITY CHECK_COMBINATION 1
Project: NUS E7 Designer: LEE
Section: 3.0 m deep TRENCH & SHAFT Date: 17/5/2019
Borelog: BH-01 Overburden Calculations on Active Pressure
σv'
Unit σv (kPa
Ground Level = 125.0 mRL Soil Type top bottom Weight (kPa) ) last strut
Water Level on Active Side = 125.0 mRL FILL 125 124.1 18 16.2 7.2
Water level on Passive Side = 122.0 mRL F2 124 124.1 19 16.2 0 h1
a x1
Lowest Strut Level = 124.1 mRL 0 124 124.1 0 16.2 0
Excavation Level = 122.0 mRL P1
Wall Toe Level = 120.00 mRL h
Partial factors for soil parameter,gØ,gc' = 1.0
Partial factors for soil parameter, gcu = 1.0
Surcharge = 11.11 kPa b
Water specific weight = 10 kN/m3

Active Pressures
Level (mRL) Soil Parameters Mobilised Parameters Water Overburden Horizontal Stresses Active Forces Moment
Ma
Drained/ Unit cu c' cu Top u Bot u cw/cu Top σv or Bot σv or Active- Active-Bot (kNm/m
Soil Type top bottom Undrained Weight (kPa) (kPa) φ' (o) (kPa) c' (kPa) φ' (o) (kPa) (kPa) or cw/c' Ka σv' (kPa) σv' (kPa) Top (kPa) (kPa) P1 (kN/m) x1 (m) )
FILL 124.1 123.50 Drained 18.0 0.0 1.0 30.0 0 1 30 9.00 15.00 0.50 0.33 7.2 12.0 13.9 21.5 10.6 0.32 3.4
G(V),N=100 123.50 120.0 Drained 20.0 0.0 10.0 35.0 0.0 10 35 15.00 50.00 0.50 0.27 12.0 47.0 9.0 53.5 109.4 2.77 302.5
Total Active Moment = 305.9 kNm/m

Passive Pressures
Level (mRL) Soil Parameters Mobilised Parameters Water Overburden Horizontal Stresses Passive Forces Moment
Mp
Drained/ Unit cu c' cu Top u Bot u cw/cu Top sv or Bot sv or Passive- Passive- (kNm/m
Soil Type top bottom Undrained Weight (kPa) (kPa) φ' (o) (kPa) c' (kPa) φ' (o) (kPa) (kPa) or cw/c' Kp sv' (kPa) sv' (kPa) Top (kPa) Bot (kPa) P1 (kN/m) x1 (m) )
G(VI),N=100 122.0 120.0 Drained 20.0 0.0 10.0 35.0 0 10 35.00 0.00 20.00 0.50 3.69 0.0 20.0 12.2 106.1 118.3 3.36 398.0
Total Passive Moment = 398.0 kNm/m
Wall Bending Moment Capacity = 45 kNm/m
Check: (Mp + Mw) / Ma = 1.41 > 1.0 = > OK!
TOE STABILITY CHECK_COMBINATION 2_COMBINATION 2
Project: NUS E7 Designer: LEE
Section: 3.0 m deep TRENCH & SHAFT Date: 17/5/2019
Borelog: BH-01 Overburden Calculations on Active Pressure
σv '
Soil Unit σv (kPa
Ground Level = 125 mRL Type top bottom Weight (kPa) ) last strut
Water Level on Active Side = 125 mRL FILL 125 124.1 18 16.2 7.2
Water level on Passive Side = 122 mRL F2 124.1 124.1 19 16.2 0 h1
a x1
Lowest Strut Level = 124 mRL 0 124.1 124.1 0 16.2 0
Excavation Level = 122 mRL P1
Wall Toe Level = 120 mRL h
Partial factors for soil parameter,gØ,gc' = 1.25
Partial factors for soil parameter, gcu = 1.4
Surcharge = 13 kPa b
Water specific weight = 10 kN/m3

Active Pressures
Level (mRL) Soil Parameters Mobilised Water Overburden Horizontal Stresses Active Forces Moment
Drained/ Unit cu c' cu c' Top u Bot u cw/cu or Top σv or Bot σv or Active- Active- P1 x1 Ma
Soil Type top bottom Undrained Weight (kPa) (kPa) φ' (o) (kPa) (kPa) φ' (o) (kPa) (kPa) cw/c' Ka σv ' (kPa) σv ' (kPa) Top (kPa) Bot (kPa) (kN/m) (m) (kNm/m)
FILL 124.1 123.5 Drained 18.0 0.0 1.0 30.0 0 0.8 24.79 9.00 15.00 0.50 0.41 7.2 12.0 16.3 24.2 12.2 0.32 3.9
G(V),N=100 123.5 120.0 Drained 20.0 0.0 10.0 35.0 0 8 29.26 15.00 50.00 0.50 0.34 12.0 47.0 13.8 60.8 130.5 2.72 354.8
Total Active Moment = 358.7 kNm/m

Passive Pressures
Level (mRL) Soil Parameters Mobilised Water Overburden Horizontal StressesPassive ForcesMoment

Drained/ Unit cu c' cu c' Top u Bot u cw/cu or Top sv or Bot sv or Passive- Passive- P1 x1 Mp
Soil Type top bottom Undrained Weight (kPa) (kPa) φ' (o) (kPa) (kPa) φ' (o) (kPa) (kPa) cw/c' Kp sv' (kPa) sv' (kPa) Top (kPa) Bot (kPa) (kN/m) (m) (kNm/m)
G(VI),N=100 122.0 120.0 Drained 20.0 0.0 10.0 35.0 0 8 29.3 0.00 20.00 0.50 2.91 0.0 20.0 9.8 88.0 97.8 3.37 329.4
Total Passive Moment = 329.4 kNm/m
Wall Bending Moment Capacity = 45 kNm/m
Check: (Mp + Mw) / Ma = 1.04 > 1.0 = > OK!

You might also like