1850

PID 1/4 DIN DOUBLE LOOP TEMPERATURE CONTROLLER

Main features
• Operator interface with large LCD display
and three configurable bar graph
• Scrolling diagnostics messages, configu-
rable, in the selected language
• Easy, guided configuration, copy/ paste
parameters even with power off
• Preventive maintenance with energy coun-
ters (kWh) and load switching
• 32 function block applications
• 8 math application blocks
• Timer, setpoint and algorithm programmer
for controlling motorized valves
• Advanced tuning of control parameters
• Different password levels
• 2 universal inputs configurable for thermo-
couples, resistance thermometers, linear
inputs
• 2 PID control loop
• 2 setpoint programmers (128 steps in 16
programs)
• Relay, logic, isolated analog outputs
• Up to two CT inputs for interrupted load
diagnostics
• RS485 serial communication in Modbus RTU
• Removable faceplate for immediate replace-
ment
• Sampling time 60 ms
Dimensions 96 × 96 × 80 mm (1/4 DIN)

PROFILE Thanks to the Smart Configurator function, analog variables and add/subtract/multiply/
you obtain the required parameter recipe divide, calculate average, root, logarithms
Operator interface
by answering a few simple questions. and control functions in cascade, and ratio
Large LCD display with customization of
Local configuration and operation with only check.
plastic front panel color and logo.
four keys assigned to LEDs that serve as Options are available with 8 digital inputs/
Graphic display of power, output current or
feedback for the pressed key and as guide outputs and 8 additional relay outputs to be
valve position. Scrolling alphameric display
to specify appropriate steps. managed via Function Blocks with state sig-
of 25 messages (32 letters each), com-
The initial parameters can always be reset, nals via dedicated LEDs on the LCD display.
pletely configurable and savable, in three
both from the keypad and from the GF_
languages. Tuning
eXpress Software tool.
Thanks to language selection and clear Advanced tuning algorithms ensure stable
scrolling messages for diagnostics, alarms, Diagnostics, Preventive Maintenance, and accurate control even with critical or
and process state, the controller speaks the and Energy Monitor very rapid thermal systems, engaging auto-
user’s language. Complete diagnostics for broken or incor- matically when necessary.
rectly connected probe, total or partial load
Control Timer
break, out of range variables, and control
Double loop, two configurable universal Three types of timers let you set delay times
loop faults.
inputs for thermocouples, resistance ther- before activating the control, hold times on
Thanks to the switching count and to the
mometers, linear inputs. the setpoint value, and timed changes of
settable alarm thresholds, you can program
Second input can be configured as remote programmed setpoints.
preventive maintenance to replace worn ac-
setpoint of single loop.
tuators. Setpoint Programmer
Easy Configuration An internal energy counter with alarm for Models with 128 steps (each step consist-
Guided configuration for manual-free abnormal variations totalizes energy con- ing of a ramp and a hold), groupable in a
programming, with a few essential sumptions and costs for constant control. maximum of 16 programs, are available for
parameters and on-line help messages. applications with setpoint profiles.
Function block applications
Ability to clone configuration among Enable inputs, event outputs, and messag-
32 AND, OR, Timer Function Blocks let you
controllers, even with power off and in the es to display can be assigned to each step.
create customizable logic sequences for
field, thanks to a mini portable configurator Double Programmer with synchronous and
complete and flexible machine control.
with Zapper battery. asynchronous base times for activating two
The controller’s hardware resources are
Extended configuration, creation of work setpoint profiles (even separate) assigned to
exploited completely, without any need for
recipes, and firmware updates via PC the two loops.
external devices such as timers and small
and GF_eXpress software, even without On-board configuration and graphic con-
PLCs.
powering the controllers. figuration with GF_eXpress.
There are 8 math Function Blocks to process
Valve Positioner Connectivity The universal main input accepts thermo-
Models to control motorized valves, with or Modbus RTU on RS485 2 wire connection. couple sensors, resistance thermometers,
without feedback. The position is calculated and linears.
General characteristics
for floating valves. For valves with potenti- The controller can be replaced at any time
The controller is completely software con-
ometer via auxiliary input you can control simply by removing the faceplate, without
figurable without accessing the internal
and display the position. any additional procedures.
electronics.

DISPLAY AND KEYS

6. Key function configurable with parameters but2 and but3.

The keys are active only when the display shows the pro-
cess variable. (HOME).
7. Up/down keys: raise/lower the value of the parameter
1 15 displayed on the SV or PV display.
8. F key: lets you navigate among controller menus and para-
2 meters. Confirms the parameter value and selects the next
14 parameter.
3 9. Key pressed signals.
10. Displays percentage of power or current, configurable with
13 parameter bArG.
4
11. Display of percentage of process variable and of setpoint.
12 12. F display: parameters, diagnostics and alarm messages.
11 Configurable with parameter dS.F (default = setpoint).
10 13. SV display: parameter values. Configurable with parameter
dS.SP (default = setpoint).
9 14. PV display: process variable.
15. Display of inputs/outputs state (only with 8 INS/OUTS and/
or 8 relays option).

5 6 7 8

1. Unit of measurement or number of program running or

number of loop displayed.
2. State of outputs OUT1, OU2, OUT3, OUT4.
3. Displays program number, step number, unit of measure-
ment (%, A, kW, kWh).
4. Controller function states:
• RUN = functioning (flashing = normal functioning,
steady on = program running);
• _/- = setpoint ramp active;
• TUN = PID parameters tuning active;
• MAN = manual/automatic (off = automatic control,
on = manual control);
• REM = remote setpoint enabled;
• SP1/2 = setpoint active (off = setpoint 1,
on = setpoint 2).
5. Work mode key (manual/automatic) in standard mode.
A function can be assigned via parameter but1.
The key is active only when the display shows the process
variable. (HOME).
DIMENSIONS AND DRILLING TEMPLATE

96 mm
3.78 in
115 mm
4.53 in
108.6 mm

3.78 in
96 mm
4.28 in

115 mm
4.53 in
mm
3.64 in
0.8
3.15 in

92 +- 0.0
0.39 in80 mm
10 mm

92 +- 0.0
0.8
mm
3.64 in

Dimensions mm/in
TECHNICAL DATA

OPERATOR INTERFACE
Type LCD black background
Screen area (L x H) 83 × 68 mm
Lighting Backlit with LEDs, life > 40,000 hours @ 25°C
(with brightness level backl = 0.8)
PV display Number of digits: 4 to 7 segments, with decimal point
Digit height: 23 mm
Color: white
SV display Number of digits: 4 to 7 segments, with decimal point
Digit height: 11 mm
Color: green
F display Number of digits: 7 to 14 segments, with decimal point
Digit height: 9 mm
Color: amber
Unit of measurement Selectable, °C, °F or custom 1
DISPLAY
Color: same as PV display
Controller state signals Number: 6 (RUN, MAN, _/-, REM, SP1/2)
Color: amber
Output state signals Number: 4 (1, 2, 3, 4)
Color: red
Bargraph indicator, configurable Type: graphic bargraph,11 segments
Power indication: 0...100% or -100...100%
Current indication: 0...100% f.s.
Valve position indication: 0...100%
Bargraph indicator Type: double bar, 11 segments
Indication of process variable and setpoint: 0...100% f.s.
Inputs/outputs state signal Number: 8 inputs, 8 outputs
(only with option) Color: green for inputs, red for outputs
Control via FB outputs
Keys number: 6, silicone (Man/Auto, L/R, *, INC, DEC, F)
KEYPAD
Type: mechanical
INPUTS
Sensor type TC, RTD (PT100, JPT100), IR ES1B, DC linear sensor
Accuracy TC input
Calibration accuracy: < ± (0,25% of reading in °C +0,1°C)
Linearization accuracy: 0,1% of reading
Cold junction accuracy: < ± 1°C a 25°C ambient temperature
Cold junction compensation: > 30:1 rejection to the change of the
ambient temperature
RTD input
Calibration accuracy: < ± (0,15% of reading in °C +0,4°C)
Temperature drift: < ± (0,005% of reading in °C +0,015°C )/°C from
25°C ambient temperature
Linearization accuracy: 0,1% of reading
Linear input:
Calibration accuracy: < 0,1% F.S.
Temperature drift: < ± 0,005% F.S. /°C from 25°C ambient tem-
perature
MAIN INPUT Sampling time 60 ms / 120 ms, selectable
Digital filter 0,0...20,0 s
Temperature unit of measurement Degrees C / F, selectable from keypad
Signal interval Type: linear
Scale: -1999...9999, settable decimal point
TC Thermocouple: J, K, R, S, T, C, D
thermocouple) input Linearization: ITS90 or custom
RTD Resistance thermometer: PT100, JPT100
(resistance thermometer) input Input impedance (Ri): ≥ 30 kΩ
Linearization: DIN 43760 or custom
Max. line resistance: 20 Ω
DC linear input 0...60 mV input impedance (Ri): > 70 kΩ
0...1 V input impedance (Ri): > 15 kΩ
0...5 V / 0...10 V input impedance (Ri): > 30 kΩ
0/4...20 mA input impedance (Ri): 50 Ω
Linearization: linear or custom
 Sensor type TC, RTD (PT100, JPT100), IR ES1B, DC linear sensor
Accuracy TC input
Calibration accuracy: < ± (0,25% of reading in °C +0,1°C)
Linearization accuracy: 0,1% of reading
Cold junction accuracy: < ± 1°C a 25°C ambient temperature
Cold junction compensation: > 30:1 rejection to the change of the
ambient temperature
RTD input
Calibration accuracy: < ± (0,15% of reading in °C +0,4°C)
Temperature drift: < ± (0,005% of reading in °C +0,015°C )/°C from
25°C ambient temperature
Linearization accuracy: 0,1% of reading
Linear input:
Calibration accuracy: < 0,1% F.S.
Temperature drift: < ± 0,005% F.S. /°C from 25°C ambient tem-
perature
AUXILIARY INPUT Sampling time 60 ms / 120 ms, selectable
Digital filter 0,0...20,0 s
Temperature unit of measurement Degrees C / F, selectable from keypad
Signal interval Type: linear
Scale: -1999...9999, settable decimal point
TC Thermocouple: J, K, R, S, T, C, D
(thermocouple) input Linearization: ITS90 or custom
RTD Resistance thermometer: PT100, JPT100
(resistance thermometer) input Input impedance (Ri): ≥ 10 MΩ
Linearization: DIN 43760 or custom
Max. line resistance: 20 Ω
DC linear input 0...60 mV input impedance (Ri): > 10 MΩ
0...1 V input impedance (Ri): > 300 kΩ
0...5 V / 0...10 V input impedance (Ri): > 300 kΩ
0/4...20 mA input impedance (Ri): 50 Ω
Linearization: linear or custom
Isolation Functional isolation 250 V
Type Isolated via external transformer
Number: 2 max
CT Max. capacity: x / 50 mA AC
(ammeter) input Line frequency: 50/60 Hz
Input impedance (Ri): 10 Ω
Accuracy ±2% f.s. ±1 digit @25 °C
Numero 5 max
Type voltage-free contact, or
DIGITAL INPUTS NPN 24 V - 4,5 mA, o
PNP 12/24 V - max 3,6 mA
For detail see electrical connections
Isolation 250 V
OUTPUTS
Relay Number: 4 max
(R) Type of relay contact: NO
Max. current: 5A (2A at ambient temperature up to 45 ° C for certi-
fication UL), 250VAC / 30 VDC, cosφ = 1
Minimum load: 5 V, 10 mA
Life cycle: > 100.000 operations
Double isolation
Logic Number: 2 max
(D) Type: for solid-state relays
Voltage: 24 V ±10% (min 10 V @20 mA)
Isolated from main input
Isolated logic Number: 2 max
(M) Type: MOS optoisolated for PLC inputs and AC/DC load
Voltage: 30 V AC/DC max
Current: 100 mA max
Resistance ON: 0,8 Ω max
Isolation: 1500 V
Triac ( long life relè) Number: 1 max
(T) Load: resistive
Voltage: 75...240 VAC
Current max: 1 A
Isolation 3 kV
snubber circuit integrated zero crossing switching
Continuous Number: 1 max
(C) Current: 4...20mA
Rout < 500 Ω
Resolution: 12 bit
Isolated from main input
Analog retransmission Number: 2 max
(A1) (A2) 0...10 V, max 20 mA, Rout: > 500 Ω
0...20 mA, 4...20 mA, Rout: < 500 Ω
Resolution: 12 bit
Isolated from main input
Number of alarm functions 4 max, assignable to an output
Possible configurations Maximum, minimum, symmetric, absolute/relative, exclusion at
ALARMS firing, memory, reset from keypad and/or contact, LBA, HB, HBB
Hold Back Band if enabled with Programmer function, alarm
after power variation at full power
For sensor VT, VT2 Voltage: 24 VDC ±10%
Current max: 30 mA
POWER SUPPLY VT option of Out3
For potentiometer VP Voltage: 1 VDC ±1%
Current max: 30 mA
INPUTS / OUTPUTS
Digital Inputs/Outputs Number: 8, in two groups (5 + 3 with separate power supply)
Input: PNP 24 VDC, 5 mA
Output: PNP with 24 VDC external power supply, ±25%, max
100 mA, short circuit protection with PTC
Isolation: 250 V
Relay Number: 8, in two groups (5 + 3 relays with common contact)
Type of relay contact: NO
Max. current: 5A (at ambient temperature up to 45 ° C for certifica-
tion UL), 250VAC / 30 VDC, cosϕ =1
Max. current for each common: 5 A
Life cycle: > 100.000 operations
Double isolation
CONTROL FUNCTIONS
Type Single/Double loop
Control PID, ON/OFF, single action heat or cool, double action heat/
cool
CONTROL Control output Continuous or ON/OFF
Cycle time: constant or optimized (BF)
Control output for motorized OPEN/CLOSE for floating motorized valve or with feedback
valves with position control by potentiometer on Relay, Solid-state,
Triac outputs.
 Number of programs Max 16 (if double loop 8 + 8)
Start / Stop / Reset / Skip via digital inputs and/or outputs from
SETPOINT logic operations
PROGRAMMER Output state: Run /Hold / Ready / End
(Double programmer if Number of steps Max 128, each with own setpoint, ramp time and hold time
double loop) Times settable in HH:MM or MM:SS
Max 4 consents, configurable for ramp and for hold
Max 4 events, configurable in ramp and in hold
Number of setpoints Max 4, selectable from digital input
MULTIPLE
Each setpoint change is subject to set ramp, different for up
SETPOINTS
and down ramp
Digital function blocks Max 32, with 4 input variables per block.
LOGIC 1 The result can act on the state of the controller, of the program-
OPERATIONS mer on alarms and outputs.
Each function has an AND, OR with TIMER block
Analog function blocks Max 8, with 2 input variables per block, with operators such as
OPERATIONS + , - , × , : , average, square root, ...
MATHEMATICAL 1 The result may act on analog variables in input to PID loops
(controlled variable, setpoint) or analog outputs .
Modes START / STOP (2 timer if double loop)
STABILIZATION (timer is on when PV enters a band set around
TIMER FUNCTION setpoint; at end of count you can activate an output, shut down
SW or change SP1/SP2)
FIRING (timed activation of control after power on)
Calculation done on nominal line voltage and nominal load power
ENERGY COUNTER
or on rms current measured on load via CT
Short circuit or open circuit (LBA alarm)
DIAGNOSTIC Interrupted or partially interrupted load (HB alarm)
Short circuit of control output (SSR alarm)
Type FRAM
RETENTIVE MEMORY Writes Number max: > 1010 cycles
Retention: > 10 years
GENERAL DATA
Operating voltage 100...240 VAC/VDC ±10%, 50/60 Hz
(20...27 VAC/VDC ±10%, 50/60 Hz)
POWER SUPPLY Power dissipation 12 W max
Protections Overvoltage 300 V / 35 V
Connection Screw terminals and crimp connector, max. wire section 1 mm2
Serial configuration port Connector: microUSB
RS485 Baudrate: 1200, 2400, 4800, 9600, 19.200, 38.400, 57.600,
(option) 115.200 bit/s
CONNECTIONS Protocol: Modbus RTU
Insulation compared to main entrance
Screw terminals and crimp connector, max. wire section 2.5 mm2
Inputs and outputs Screw terminals and crimp connector, max. wire section 2.5 mm2
Use Internal
Altitude 2000 m max
AMBIENT
Operating temperature -10 ... +55 °C (as per IEC 68-2-14)
CONDITIONS
Storage temperature -20 ... +70 °C (as per IEC 68-2-14)
Relative humidity 20...85% RH non condensante (as per IEC 68-2-3)
PROTECTION LEVEL IP 65 on front panel (as per IEC 68-2-3)
Positioning On panel, removable faceplate
Installation regulations Installation category: II
ASSEMBLY
Pollution degree: 2
Isolation: double
DIMENSIONS 96 X 96 mm (1/4 DIN)
Depth: 80 mm
WEIGHT 0,24 kg
EMC Conforms to Directive 2014/30/EU norme EN 61326-1
CE STANDARDS (electromagnetic compatibility) Emissions in industrial environment classe A
LVD safety Conforms to Directive 2014/35/EU norme EN 61010-1

1) Programming is done with the GF_eXpress configuration program.

ACCESSORIES

Code Description
F060800 Cable for programming with PC, USB-TTL 3 V with USB – microUSB connectors, length 1.8 m
F043958 “GF_eXpress” software CD
F060909 Configuration kit for new instruments
51970 Rubber gasket 96×96 front box
51069 Rubber gasket 99×96 box-panel
49030 Fastening box to panel
51328 Protection of contacts at box bottom
51738 36 contacts at box bottom
330200 Current transformer (CT) 50/0.05 A
330201 Current transformer (CT) 25/0.05 A
CONNECTION DIAGRAM

37 36 12 37 36 12
C
38

39
35

34
11

10
38

39
35

34
11

10 ~ 37 36 12 ~
40 33 9 40 33 9
OUT 4 PWR
41

42
32

31
8

7
41

42
32

31
8

7
~ 38 35 11 ~
43 30 6 43 30 6
NO
44 29 5 44 29 5

45 28 4 45 28 4
C
46

47
27

26
3

2
46

47
27

26
3

2
39 34 10 + +
VT OUT 3
48 25 1 48 25 1

- -
40 33 9
NO
C
IN 5 41 32 8 +

-
OUT 2
IN 4 42 31 7
NO
C
IN 3 43 30 6 + +
C
- -
OUT 1
IN 2 44 29 5
NO
+
IN 1 45 28 4
5 V, 10 V

COM 46 27 3
B (Data +) + +
Option 47 26 2 T T
60 mV, 1 V, 20 mA
Modbus RTU (M) = M0
A (Data -)
Communication 48 25 1
- - -

Main input
36
CT1 CT1 = Current transformer
35 CT2 = Second current transformer
for 2-phase /3-phase load
34
CT2
33

32 +
OUT A2
31 -

30 +
OUT A1
29 -

+
28
5 V, 10 V
+ +
27
VP VT2
+ + +
26 T T
1 V, 20 mA
60 mV
25 - - -
-
Auxiliary input
for models with option auxiliary input
=1 =2o3
LEGEND

~ NO
PWR Power supply Isolated digital Relay output
~ inputs
C
+ +
B (Data +)
Linear input in Thermocouple ~ Long-life solid state RS485 serial line
voltage / current input ~ relay output
- A (Data -)
-
+
Input for
current - Logic output +
Input VT Supply transmitter
transformer PT100 -
T T
+ JPT100 Isolated logic output
2 / 3 wires +
AUX Auxiliary input VP Supply potentiometer
+ -
-
-
Isolated analog output

! ATTENTION: For correct installation, read the warnings in the instruction manual.
CONNECTION DIAGRAM

37

38
36

35
12

11
37

38
36

35
12

11
8 (PNP) digital Inputs/Outputs 8 Relays
39 34 10 39 34 10

40 33 9 40 33 9

41 32 8 41 32 8

42 31 7 42 31 7

43 30 6 43 30 6

44 29 5 44 29 5

+
45 28 4 45 28 4

46 27 3 46 27 3 37 36 12
47

48
26

25
2

1
47

48
26

25
2

1
External power supply
24 VDC ±25%, max 3.5W
GND 38 35 11 GND
External power supply C
24 VDC ±25%, max 27W + 39 34 10 COM 14...18
IN 6
NO
OUT 6 LOAD 40 33 9 OUT 14
IN 7
NO
OUT 7 LOAD 41 32 8 OUT 15
IN 8
NO
OUT 8 LOAD 42 31 7 OUT 16
IN 9
NO
OUT 9 LOAD 43 30 6 OUT 17
IN 10
NO
OUT 10 LOAD 44 29 5 OUT 18
C
45 28 4 COM 19...21
IN 11
NO
OUT 11 LOAD 46 27 3 OUT 19
IN 12
LOAD NO
OUT 12 47 26 2 OUT 20
IN 13
NO
OUT 13 LOAD 48 25 1 OUT 21

! ATTENTION: For correct installation, read the warnings in the instruction manual.
ORDER METHODS

A B CD E F G H I L M N O P
Ordering code: 1850 X - X - X X X - 0 - X - X X - X - X X - X X - X - X X

Model (A) Fonction (P)

Controller 00 Absent
Programmer P Logical + mathematical
FB
Valve 5 V operations
Programmer+valve 5 PV
Supply (O)
Output 1 (B) 0 20...27 VAC / VDC
Relay R 1 100...240 VAC / VDC
Logic D
I/O optional (N) 4
Analog C
00 Absent
Output 2 (C) - Output 3 (D) 10 8 IN/OUT
Relay - Relay R R 01 8 relay
Logic - Logic D D 11 8 IN/OUT + 8 relay
Isolated logic - Isolated logic M M
Communication (M)
Relay - VT 24 V R V
00 Absent
Logic - VT 24 V D V
M0 RS485 Modbus RTU
Isolated logic - VT 24 V M V

Output 4 (E) Digital inputs (L)

Absent 0 0 Absent 3
Relay R 5 5 DI
Long Life relay T
Auxiliary input (I)
0 Absent
Retransmission (G)
1 Input Aux 2
Absent 0
2 Input Aux + VP 1 V 1
Analogue A1 1
3 Input Aux + VT2 24 V 1
Analogue A1 + A2 2
CT Input (H)
0 Absent
2 CT1 + CT2

Note
1) Auxiliary input type 1 V / 5 V / 10 V / 20 mA
2) Auxiliary input type TC / RTD / 60 mV
3) Only for option H-I = 0
4) The N options require P = FB option
5) V and PV models required (CD) =RR

Check before each request a list of codes available on the following pages
ORDER METHODS

Power supply 100...240 VAC/VDC

I/O Communica-
Inputs Outputs
AUX tions

Logic + mathematical functions

AUX (1V/5V/10V/20mA) +VP
AUX (1V/5V/10V/20mA) +VT

Digital Inputs / Outputs

Total

AUX ( TC/RTD/60mV)

Power supply sensor

RS485 modbus RTU

Code F Model Number
of Outputs

Logic isolated

Outputs relay
Programmer

Logic SSR

Analog V/I
Analog I
Digital
Valves

Relay
Triac
CT
F065321 1850-D-RVR-0-0-00-5-00-00-1-00 5 2 1 •
3 outputs
F065322 1850-R-RVR-0-0-00-5-00-00-1-00 5 3 •
F067164 1850-R-DDR-0-0-01-5-00-00-1-FB 5 • 2 2 •
F065331 1850-R-DDR-0-0-03-5-00-00-1-FB 5 • 2 2 •
F067165 1850-R-DDR-0-0-01-5-M0-00-1-FB 5 • 2 2 • •
F065332 1850-R-DDR-0-0-03-5-M0-00-1-FB 5 • 2 2 • •
F067167 1850-C-RRR-0-0-01-5-00-00-1-FB 5 • 3 1 •
F067168 1850-C-RRR-0-0-03-5-00-00-1-FB 5 • 3 1 •
F065334 1850-D-RRR-0-0-20-0-M0-00-1-00 2 3 1 •
F065350 1850V-D-RRR-0-0-02-5-M0-00-1-00 • 5 • 3 1 •
4 outputs
F065355 1850P-D-RRR-0-0-00-5-00-00-1-00 • 5 3 1
F067169 1850P-D-RRR-0-0-01-5-00-00-1-FB • 5 • 3 1 •
F065361 1850P-D-RRR-0-0-03-5-00-00-1-FB • 5 • 3 1 •
F065370 1850PV-D-RRR-0-0-02-5-00-00-1-FB • • 5 • 3 1 •
F065330 1850-R-RRR-0-0-02-5-00-00-1-00 5 • 4
F065348 1850V-R-RRR-0-0-02-5-00-00-1-00 • 5 • 4
F067172 1850V-R-RRR-0-0-01-5-00-00-1-00 • 5 • 4
F065349 1850V-R-RRR-0-0-03-5-00-00-1-00 • 5 • 4
F067173 1850-R-DDR-0-2-01-5-00-10-1-FB 5 • 2 2 2 • •
F067174 1850-R-DDR-0-2-03-5-00-10-1-FB 5 • 2 2 2 • •
4 (+8 )
F067175 1850-R-DDR-0-2-01-5-M0-01-1-FB 5 • 2 2 2 • • •
outputs
F067176 1850-R-DDR-0-2-03-5-M0-01-1-FB 5 • 2 2 2 • • •
F065368 1850P-R-RRR-0-0-00-5-00-10-1-FB • 5 4 • •
F067179 1850-R-RVR-0-2-01-5-M0-00-1-00 5 • 3 2 • •
F065340 1850-R-RVR-0-2-03-5-M0-00-1-00 5 • 3 2 • •
F065351 1850V-D-RRR-0-1-02-5-00-00-1-00 • 5 • 3 1 1
F065352 1850V-D-RRR-0-1-02-5-M0-00-1-00 • 5 • 3 1 1 •
F067180 1850V-D-RRR-0-1-01-5-M0-00-1-00 • 5 • 3 1 1 •
F065353 1850V-D-RRR-0-1-03-5-M0-00-1-00 • 5 • 3 1 1 •
F065354 1850V-R-RR0-0-2-00-0-00-00-1-00 • 3 2
5 outputs
F065364 1850P-D-RRR-0-1-02-5-M0-00-1-00 • 5 • 3 1 1 •
F067181 1850-R-RRR-0-1-01-5-00-00-1-00 5 • 4 1
F065338 1850-R-RRR-0-1-03-5-00-00-1-00 5 • 4 1
F067182 1850-R-RRR-0-1-01-5-M0-00-1-00 5 • 4 1 •
F065339 1850-R-RRR-0-1-03-5-M0-00-1-00 5 • 4 1 •
F067183 1850P-R-RRR-0-1-01-5-M0-00-1-00 • 5 • 4 1 •
F065365 1850P-R-RRR-0-1-03-5-M0-00-1-00 • 5 • 4 1 •

Note: Please contact GEFRAN for information on available codes.

Power supply 100...240 VAC/VDC

I/O Communica-
Inputs Outputs
AUX tions

Logic + mathematical functions

AUX (1V/5V/10V/20mA) +VP
AUX (1V/5V/10V/20mA) +VT

Digital Inputs / Outputs

Total

AUX ( TC/RTD/60mV)

Power supply sensor

RS485 modbus RTU

Code F Model Number
of Outputs

Logic isolated

Outputs relay
Programmer

Logic SSR

Analog V/I
Analog I
Digital
Valves

Relay
Triac
CT
F065341 1850-D-RRR-0-2-02-5-00-00-1-00 5 • 3 1 2
F067184 1850P-D-RRR-0-2-01-5-00-00-1-00 • 5 • 3 1 2
F065366 1850P-D-RRR-0-2-03-5-00-00-1-00 • 5 • 3 1 2
6 outputs
F065367 1850P-D-RRR-0-2-20-5-M0-00-1-00 • 5 2 3 1 2 •
F067185 1850-R-RRR-0-2-01-5-M0-00-1-00 5 • 4 2 •
F065342 1850-R-RRR-0-2-03-5-M0-00-1-00 5 • 4 2 •
F067187 1850P-R-RRR-0-2-01-5-M0-10-1-FB • 5 • 4 2 • • • 6 (+8 )
F065369 1850P-R-RRR-0-2-03-5-M0-10-1-FB • 5 • 4 2 • • • outputs

Note: Please contact GEFRAN for information on available codes.

Power supply 20...27 VAC/VDC

I/O Communica-
Inputs Outputs

Logic + mathematical functions

AUX tions

AUX (1V/5V/10V/20mA) +VP

AUX (1V/5V/10V/20mA) +VT

Digital Inputs / Outputs

AUX ( TC/RTD/60mV)

Power supply sensor

Total

RS485 modbus RTU

Code F Model Number
of Outputs

Logic isolated

Outputs relay
Programmer

Logic SSR

Analog V/I
Analog I
Digital
Valves

Relay
Triac
CT
F065269 1850-D-RVR-0-0-00-5-00-00-0-00 5 2 1 •
3 outputs
F065270 1850-R-RVR-0-0-00-5-00-00-0-00 5 3 •
F067188 1850-R-DDR-0-0-01-5-00-00-0-FB 5 • 2 2 •
F065279 1850-R-DDR-0-0-03-5-00-00-0-FB 5 • 2 2 •
F067189 1850-R-DDR-0-0-01-5-M0-00-0-FB 5 • 2 2 • •
F065280 1850-R-DDR-0-0-03-5-M0-00-0-FB 5 • 2 2 • •
F067191 1850-C-RRR-0-0-01-5-00-00-0-FB • 5 • 3 1 •
F067192 1850-C-RRR-0-0-03-5-00-00-0-FB • 5 • 3 1 •
F065282 1850-D-RRR-0-0-20-0-M0-00-0-00 2 3 1 •
F065298 1850V-D-RRR-0-0-02-5-M0-00-0-00 • 5 • 3 1 •
4 outputs
F065303 1850P-D-RRR-0-0-00-5-00-00-0-00 • 5 3 1
F067193 1850P-D-RRR-0-0-01-5-00-00-0-FB • 5 • 3 1 •
F065309 1850P-D-RRR-0-0-03-5-00-00-0-FB • 5 • 3 1 •
F065318 1850PV-D-RRR-0-0-02-5-00-00-0-FB • • 5 • 3 1 •
F065278 1850-R-RRR-0-0-02-5-00-00-0-00 5 • 4
F065296 1850V-R-RRR-0-0-02-5-00-00-0-00 • 5 • 4
F067196 1850V-R-RRR-0-0-01-5-00-00-0-00 • 5 • 4
F065297 1850V-R-RRR-0-0-03-5-00-00-0-00 • 5 • 4
F067197 1850-R-DDR-0-2-01-5-00-10-0-FB 5 • 2 2 2 • •
F067198 1850-R-DDR-0-2-03-5-00-10-0-FB 5 • 2 2 2 • •
4 (+8 )
F067199 1850-R-DDR-0-2-01-5-M0-01-0-FB 5 • 2 2 2 • • •
outputs
F067200 1850-R-DDR-0-2-03-5-M0-01-0-FB 5 • 2 2 2 • • •
F065316 1850P-R-RRR-0-0-00-5-00-10-0-FB • 5 4 • •
F067203 1850-R-RVR-0-2-01-5-M0-00-0-00 5 • 3 2 • •
F065288 1850-R-RVR-0-2-03-5-M0-00-0-00 5 • 3 2 • •
F065299 1850V-D-RRR-0-1-02-5-00-00-0-00 • 5 • 3 1 1
F065300 1850V-D-RRR-0-1-02-5-M0-00-0-00 • 5 • 3 1 1 •
F067204 1850V-D-RRR-0-1-01-5-M0-00-0-00 • 5 • 3 1 1 •
F065301 1850V-D-RRR-0-1-03-5-M0-00-0-00 • 5 • 3 1 1 •
F065302 1850V-R-RR0-0-2-00-0-00-00-0-00 • 3 2
5 outputs
F065312 1850P-D-RRR-0-1-02-5-M0-00-0-00 • 5 • 3 1 1 •
F067205 1850-R-RRR-0-1-01-5-00-00-0-00 5 • 4 1
F065286 1850-R-RRR-0-1-03-5-00-00-0-00 5 • 4 1
F067206 1850-R-RRR-0-1-01-5-M0-00-0-00 5 • 4 1 •
F065287 1850-R-RRR-0-1-03-5-M0-00-0-00 5 • 4 1 •
F067207 1850P-R-RRR-0-1-01-5-M0-00-0-00 • 5 • 4 1 •
F065313 1850P-R-RRR-0-1-03-5-M0-00-0-00 • 5 • 4 1 •

Note: Please contact GEFRAN for information on available codes.

Power supply 20...27 VAC/VDC

I/O Communica-
Inputs Outputs

Logic + mathematical functions

AUX tions

AUX (1V/5V/10V/20mA) +VP

AUX (1V/5V/10V/20mA) +VT

Digital Inputs / Outputs

AUX ( TC/RTD/60mV)

Power supply sensor

Total

RS485 modbus RTU

Code F Model Number
of Outputs

Logic isolated

Outputs relay
Programmer

Logic SSR

Analog V/I
Analog I
Digital
Valves

Relay
Triac
CT
F065289 1850-D-RRR-0-2-02-5-00-00-0-00 5 • 3 1 2
F067208 1850P-D-RRR-0-2-01-5-00-00-0-00 • 5 • 3 1 2
F065314 1850P-D-RRR-0-2-03-5-00-00-0-00 • 5 • 3 1 2
6 outputs
F065315 1850P-D-RRR-0-2-20-5-M0-00-0-00 • 5 2 3 1 2 •
F067209 1850-R-RRR-0-2-01-5-M0-00-0-00 5 • 4 2 •
F065290 1850-R-RRR-0-2-03-5-M0-00-0-00 5 • 4 2 •
F067211 1850P-R-RRR-0-2-01-5-M0-10-0-FB • 5 • 4 2 • • • 6 (+8 )
F065317 1850P-R-RRR-0-2-03-5-M0-10-0-FB • 5 • 4 2 • • • outputs

Note: Please contact GEFRAN for information on available codes.

UL Conformity C/UL/US File no. E216851

EMC: Compliance with Directive 2014/30 / EU, with reference to EN 61326-1 emission in industrial environment class A
Security LVD: Compliance with Directive 2014/35 / EU, with reference to EN 61010-1

GEFRAN spa via Sebina,74 - 25050 Provaglio d’Iseo (BS)

Tel. 03098881 - fax 0309839063 - Internet: http://www.gefran.com DTS_1850_03-2017-ENG