Data sheet 6EP1931-2DC21

SITOP DC UPS MODULE 6A WITHOUT INTERFACE

SITOP Module 24 V USC DC /6 A Uninterrupted Power supply
without interface input: 24 V DC/6.85 A output: 24 V DC/6 A

Input
Supply voltage at DC Rated value 24 V
Voltage curve at input DC
input voltage range 22 ... 29 V DC
Adjustable response value voltage for buffer 22.5 V
connection preset
Adjustable response value voltage for buffer 22 ... 25.5 V; Adjustable in 0.5 V increments
connection
Input current at rated input voltage 24 V Rated value 6 A; + approx. 0.6 A with empty battery

Mains buffering
Type of energy storage with batteries
Design of the mains power cut bridging-connection Dependent on connected battery and load current, see selection
table battery module and mains buffering times as well as the
relevant important information notes!
Charging current 0.2 A, 0.4 A
adjustable charging current maximum Note factory setting approx. 0.4 A

Output
Output voltage
● in normal operation at DC Rated value 24 V

6EP1931-2DC21 Subject to change without notice

Page 1/4 02/12/2018 © Copyright Siemens
 ● in buffering mode at DC Rated value 24 V
Formula for output voltage Vin - approx. 0.5 V
ON-delay time typical 1 s
Voltage increase time of the output voltage typical 60 ms
Output voltage in buffering mode at DC 19 ... 28.5 V
Output current
● Rated value 6 A
● in normal operation 0 ... 6 A
● in buffering mode 0 ... 6 A
Peak current 6.3 A
Property of the output Short-circuit proof Yes
Supplied active power typical 144 W

Efficiency
Efficiency in percent
● at rated output current for rated value of the 95 %
output current typical
● in case of accumulator operation typical 94.5 %
Power loss [W]
● at rated output current for rated value of the 7 W
output current typical
● in case of accumulator operation typical 8 W

Protection and monitoring

Product function
● reverse polarity protection against energy Yes
storage unit polarity reversal
● reverse polarity protection against input voltage Yes
polarity reversal

Signaling
Display version
● for normal operation Normal operation: LED green (OK), floating changeover contact
"Bat/OK" to setting "OK" ("OK" means: Voltage of the supplying
power supply unit is greater than cut-in threshold set at the DC
UPS module); Lack of buffer standby: LED red (alarm), floating
changeover contact "Alarm/Bat" to setting "Alarm"; Battery
replacement required: LED red (alarm) flashing with approx. 0.25
Hz, floating changeover contact "Alarm/Bat" switching with
approx. 0.25 Hz; Energy storage > 85%: LED green (Bat > 85%),
floating NO contact "Bat > 85" closed; Permissible contact current
capacity: DC 60 V/1 A or AC 30 V /1 A
● in buffering mode Buffered mode: LED yellow (Bat), floating changeover contact
"OK/Bat" to setting "Bat"; Prewarning battery voltage < 20.4 VDC:
LED red (alarm), floating changeover contact "Alarm/Bat" to
setting "Alarm"; Energy storage > 85%: LED green (Bat > 85%),
floating NO contact "Bat > 85" closed

6EP1931-2DC21 Subject to change without notice

Page 2/4 02/12/2018 © Copyright Siemens
 Interface
Product component PC interface No
Design of the interface without

Safety
Galvanic isolation between entrance and outlet No
Operating resource protection class Class III
Certificate of suitability
● CE marking Yes
● as approval for USA cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259
● relating to ATEX -
● C-Tick No
Shipbuilding approval GL, ABS
Protection class IP IP20

EMC
Standard
● for emitted interference EN 55022 Class B
● for interference immunity EN 61000-6-2

Operating data
Ambient temperature
● during operation -25 ... +60 °C; with natural convection
● during transport -40 ... +85 °C
● during storage -40 ... +85 °C
Environmental category acc. to IEC 60721 Climate class 3K3, no condensation

Mechanics
Type of electrical connection screw-type terminals
● at input 24 V DC: 2 screw terminals for 1 ... 4 mm²/17 ... 11 AWG
● at output 24 V DC: 4 screw terminals for 1 ... 4 mm²/17 ... 11 AWG
● for battery module 24 V DC: 2 screw terminals for 1 ... 4 mm²/17 ... 11 AWG
● for control circuit and status message 10 screw terminals for 0.5 ... 2.5 mm²/20 ... 13 AWG
Width of the enclosure 50 mm
Height of the enclosure 125 mm
Depth of the enclosure 125 mm
Required spacing
● top 50 mm
● bottom 50 mm
● left 0 mm
● right 0 mm
Net weight 0.4 kg
Product feature of the enclosure housing for side-by- Yes
side mounting
Mounting type Snaps onto DIN rail EN 60715 35x7.5/15

6EP1931-2DC21 Subject to change without notice

Page 3/4 02/12/2018 © Copyright Siemens
 Electrical accessories Battery module
MTBF at 40 °C 1 085 776 h
Equipment marking acc. to DIN EN 81346-2 T
Other information Specifications at rated input voltage and ambient temperature +25
°C (unless otherwise specified)

6EP1931-2DC21 Subject to change without notice

Page 4/4 02/12/2018 © Copyright Siemens