Main Socket Holding Anchor Rod
Uploaded by
ARVIND SINGH RAWATMain Socket Holding Anchor Rod
Uploaded by
ARVIND SINGH RAWATMain Socket holding Anchor Rod
5180 KN
A1 = 180 Ф
A2 = 100 Ф
2590 KN 2590 KN
700
25 180 25
1 5 1
###
3 2 2 3
250 ###
25 4 6 4
180 32
360
2 Plate 1 : 25 x 260 mm
2 Plate 2 : 250 x 25 mm
2 Plate 3 : 250 x 25 mm
2 Plate 4 : 90 x 32 mm
1 Gap 5 : 25 x 180 mm
1 Gap 6 : 32 x 180 mm
Section Properties :
TAKING MOMENT ABOUT TOP OF MEMBER
SECTION A Y AY AYY IXX
2 Plate 1 13000 12.5 162500 2031250 ###
2 Plate 2 12500 150 1875000 281250000 65104167
2 Plate 3 12500 150 1875000 281250000 65104167
2 Plate 4 5760 291 1676160 487762560 491520
TOTAL 43760 5588660 1052293810 131376937
Ytop = S AY / S A = 5588660 / 43760 = 127.71 mm
TOTAL DEPTH = 275 mm
Ybottom = 275 - ### = 147.29 mm
INA = S AYY + S IXX - S A x Yt ^ 2
= 1052293810 + 131376937 - 43760 x 127.71 ^ 2
= 1183670747 - 713736759 = 469933987 mm4
Iyy = 2384005667 mm4
Zxx = ( INA / ymax )= ### mm3
Zyy = ( Iyy / xmax )= ### mm3
Rxx = Sqrt ( INA / A )= 103.63 mm
Ryy = Sqrt ( Iyy / A )= 233.41 mm
As per loading Conditions :
5180 KN
450 mm
Ra Rb
2590 KN 2590 KN
Max BM. = 5180 x 0.45 = 582.75 KN.m
4
Grade of steel used for Socket Members = E410 fy = 390 Mpa
Maximum Bending Stresses = 582.75 x 1000000 = 182.65 Mpa
3190570
Permissible Bending Stresses = 0.66 x fy
= 0.66 x 390 = 257.4 Mpa
Hence Safe
IYY
### 1 Gap 5 4500 12.5 56250 703125
351354167 1 Gap 6 5760 291 ### ###
1221354167
108864000
2384005667
PRIS AX 437.6 IZ ### IY ### YD 27.5
Mpa
Mpa
Mpa
234375 234375
491520 491520
ZD 70
page :7 of10
CONNECTIONS :
Connections of suspenders with Suspension Cable :
Grade of Plates E
Ultimate Strength of Plate fu =
Yielding Strength of Plate fy =
Grade of Pin E
Ultimate Strength of Pin fu =
yield strength of pin fyp =
Design of Pin : P
27 mm Thick
14 mm Thick P
58
20 mm Thick
p'= P/2 P/2 P/2
62
Ultimate pull transmitted by 20 + 2 x 14 mm plate P =
Max Bending Moment = Pl/4 = 220 x 58 =
4
Assuming that the pin is a cylindrically shaped beam and is not intended to be removed
∴ Diameter of pin , d
Mu = 1.5 fyp Z
Mu = 1.5 fyp (πd3/32)
d = [ 21.33 Mu /(π fyp) ]
1/3
d= [ 21.33 x 3190 x 10^3 /( 3.14159265 x 390 )]^
=
Provided Min. Dia of Pin
Provided Dia of pin = 55 mm
Area of pin A= 3.1416 / 4 x 55 ^ 2 =
Min. thickness of the connected part. t =
Shear Capacity of Pin :
The shear capacity of pin may be taken as follows :
* If rotation is not required and pin is not intended to be removed :
0.6 fyp A = 0.6 x 530 x 2375.8 =
>
page :8 of10
Bearing Capacity of Pin : Hence SAFE
The Bearing capacity of pin may be taken as follows :
* If rotation is not required and pin is not intended to be removed :
1.5 fyp d t = 1.5 x 530 x 55 x 27 =
>
Hence SAFE
DESIGN STRENGTH OF YIELDING OF GROSS SECTION (PLATE)
Material of plate = Mild steel
Effective Width of Plate b = 174 mm
Thickness of connected Plates t = 34 mm
Area of Plate Ag = 5916 mm2
Tdg = (Ag*fy/ϒm0) =( 5916 x 530 / 1.1 )x
Tdg =
RUPTURE OF CRITICAL SECTION
Net effective Area An =
Tdn = (0.9*fu*An)/ϒm1 = 0.9 x 650 x 3978
1.25 x 10 ^ -3
Tdn =
therefore ,Tensile strength of plate is =
Factored Tensile Force on the Plate = 1.5 x 220 =
Hence SAFE
-x-x-x-
page :9 of10
550
650 N/mm2
530 N/mm2
410
540 N/mm2
390 N/mm2
P/2
220 KN
3190 KN mm
1/3
38.15 mm
40 mm
2375.829 mm2
27 mm
755.5 KN
220 KN
page :10 of10
Hence SAFE
1180.575 KN
220 KN
Hence SAFE
10 ^ -3
2850.436 KN
3978 mm2
1861.704 KN
1861.704 KN
330 KN
Hence SAFE
