ManualsOperator 3007

O PERATO R’S M ANU AL AND PARTS LIST
® SULLAIR ®
INDUSTRIAL AIR COMPRESSOR

3000, 3000P, 3700, 4500,
3000V, 3000PV, 3700V, 4500V
30, 37 & 45 KW/40, 50 & 60HP
Air-Cooled and Water-Cooled
Standard & 24 KT
PART NUMBER:
02250155-601
KEEP FOR
FUTURE
REFERENCE
© SULLAIR CORPORATION
The information in this document is
correct at the time of printing for utility
compressor serial number
20060701XXXX
and all subsequent serial numbers.
® SULLAIR ®
AIR CARE SEMINAR TRAINING
Sullair Air Care Seminars are courses that provide hands-on instruction in the proper operation, maintenance
and service of Sullair equipment. Individual seminars on Industrial compressors and compressor electrical
systems are presented at regular intervals throughout the year at a dedicated training facility at Sullair's corporate
headquarters in Michigan City, Indiana.
Instruction includes discussion of the function and installation of Sullair service parts, troubleshooting of the
most common problems, and actual equipment operation. The seminars are recommended for Maintenance
and Contractor Maintenance and Service Personnel.
For detailed course outlines, schedule and cost information contact:
Sullair Customer Care Training Department
: 1-888-SULLAIR or
219-879-5451 (ext. 5623)
www.sullair.com
- Or Write -
Sullair Corporation
3700 E. Michigan Blvd.
Michigan City, IN 46360
Attn: Service Training Department
® SULLAIR ®
TABLE OF CONTENTS
1 - SAFETY...................................................................................................1
General...................................................................................................1
Personal Protective Equipment..................................................................1
Pressure Release.....................................................................................1
Fire and Explosion....................................................................................2
Moving Parts............................................................................................2
Hot Surfaces, Sharp Edges and Sharp Corners............................................3
Toxic and Irritating Substances..................................................................3
Electrical Shock.......................................................................................3
Lifting......................................................................................................4
Entrapment..............................................................................................4
2 - DESCRIPTION.........................................................................................5
Introduction..............................................................................................5
Description of Components.......................................................................8
Sullair Compressor Unit, Functional Description..........................................8
Compressor Cooling and Lubrication System, Functional
Description............................................................................................11
Compressor Discharge System, Functional Description..............................11
Control System, Functional Description.....................................................12
Start Mode - 0 to 50 PSIG (0 to 3.5 Bar)................................................12
Full Load Mode - 50 to 100 PSIG (3.4 to 6.9 BAR).................................13
Modulating Mode - 100 to 110 PSIG (6.9 to 7.6 BAR).............................13
Unload Mode- In Excess of 110 PSIG (7.6 BAR)...................................13
Load / No Load Control......................................................................13
Automatic Operation.........................................................................13
Air Inlet System, Functional Description....................................................14
3 - SPECIFICATIONS..................................................................................17
Table of Specifications - 3000, 3000P, 3700 and 4500 Series
Models..................................................................................................17
Table of Specifications - Variable Speed Drive Models................................18
Compressor Specifications......................................................................19
Lubrication Guide...................................................................................20
Application Guide...................................................................................20
Lubrication Change Recommendations and Maintenance, Fluid Filter and
Separator...............................................................................................21
Identification, Air-Cooled, Standard and VSD.............................................22
Identification, Water-Cooled....................................................................24
Piping and Instrumentation, Air-Cooled.....................................................26
Piping and Instrumentation, Water-Cooled................................................30
Wiring Diagram, MFV Air-Cooled.............................................................34
® SULLAIR ®
3000-4500 Operator’s Manual and Parts List iii
TABLE OF CONTENTS
Wiring Diagram, MFV Water-Cooled.........................................................36

Wiring Diagram, Wye-Delta Air-Cooled.....................................................38
Wiring Diagram, Wye-Delta Water-Cooled................................................40
Wiring Diagram, VSD Air-Cooled..............................................................42
Wiring Diagram, VSD Water-Cooled.........................................................44
Wiring Diagram, VSD Air-Cooled, 575V Series Delta..................................46
Wiring Diagram, VSD Water-Cooled, Series Delta 575V..............................48
4 - INSTALLATION......................................................................................51
Mounting of Compressor.........................................................................51
Ventilation and Cooling...........................................................................51
Air-Cooled Compressors...................................................................51
Water-Cooled Compressors..............................................................52
Service Air Piping...................................................................................55
Pipe Sizing.......................................................................................55
Use of Auxiliary Receiver Tank...........................................................55
Isolation Valve(s)..............................................................................55
Fluid Containment............................................................................55
Coupling Alignment Check......................................................................56
Fluid Level Check...................................................................................56
Electrical Preparation..............................................................................56
Motor Rotation Direction Check ...............................................................56
5 - WS CONTROLLER.................................................................................57
Controller Layout....................................................................................57
Controller Keypad...................................................................................57
LCD Display...........................................................................................58
LED Lights.............................................................................................59
6 - MAINTENANCE......................................................................................61
General.................................................................................................61
Daily Operation......................................................................................61
Maintenance After Initial 50 Hours of Operation..........................................61
Maintenance Every 2000 Hours...............................................................62
Fluid Maintenance .................................................................................62
Filter Maintenance..................................................................................62
Fluid Filter Element Replacement.......................................................62
Air Filter Maintenance .............................................................................62
Air Filter Element Replacement..........................................................63
Separator Maintenance ..........................................................................63
Separator Element Replacement........................................................63
Oil Return/Sight Glass Maintenance...................................................64
Pressure Regulator Adjustment..........................................................65
Water Condensate Drain Maintenance...............................................65
Control Line Strainer.........................................................................65
Shaft Coupling Maintenance..............................................................65
Troubleshooting - Introduction.................................................................65
Troubleshooting Guide............................................................................66
7 - VSD CONTROL OPERATION..................................................................69
Description of Components.....................................................................69
Control System, Functional Description.....................................................69
Start Mode- 0 to 50 PSIG (0 to 3.5 Bar)................................................69
Full Load Mode- 50 to 100 PSIG (3.4 to 6.9 Bar)....................................69
Variable Speed Drive Part Load Control..............................................69
Modulating Mode- 100 to 106 PSIG (7.3 to 6.9 Bar) ..............................69
Unload Mode- In Excess of 106 PSIG (7.3 Bar) ....................................70
8 - PARTS LISTS.........................................................................................71
Procedure For Ordering Parts..................................................................71
iv 3000-4500 Operator’s Manual and Parts List

® SULLAIR ®
TABLE OF CONTENTS
Recommended Spare Parts List...............................................................73

Compressor, Frame and Drive, 3000P and 3700 Models.............................74
Compressor, Frame and Drive, 3000 Model With 10 Series
Unit.......................................................................................................76
Compressor, Frame and Drive, 4500 Model...............................................78
Air Inlet System, Standard 3000P, 3700 And 4500 Series............................80
Air Inlet System, 10 Series 3000...............................................................82
Air Piping, Air-Cooled..............................................................................84
Air Piping, Water-Cooled.........................................................................86
Fluid Piping, Air-Cooled...........................................................................88
Fluid Piping, Water-Cooled......................................................................90
Cooling and Lubrication System, Air-Cooled 18"/60Hz Fan, Standard
Cooler................................................................................................... 92
Fluid Cooling System, Water-Cooled........................................................94
Discharge, Receiver and Piping System, 3000P, 3700 and
4500......................................................................................................96
Discharge, Receiver and Piping, 3000 With 10 Series
Unit.....................................................................................................100
Moisture Drain......................................................................................104
Pneumatic Control System, With Standard Sequencing............................106
Control System and Electric Parts, MFV..................................................108
Control System and Electric Parts, WYE-Delta.........................................112
Control System and Electric Parts, VSD..................................................116
Enclosure, Air-Cooled...........................................................................120
Enclosure, Water-Cooled......................................................................122
Decal Locations, Air-Cooled..................................................................124
Decal Locations, Water-Cooled..............................................................128
Decal Group.........................................................................................132
® SULLAIR ®
3000-4500 Operator’s Manual and Parts List v
TABLE OF CONTENTS
THIS PAGE INTENTIONALLY LEFT BLANK
vi 3000-4500 Operator’s Manual and Parts List

® SULLAIR ®
® SULLAIR ®
Section 1
SAFETY
While not specifically applicable to all types of
NOTE compressors with all types of prime movers, most of the
precautionary statements contained herein are applicable
to most compressors and the concepts behind these
statements are generally applicable to all compressors.
1.2 PERSONAL PROTECTIVE

EQUIPMENT
OPERATOR IS REQUIRED TO READ Prior to installing or operating the compressor, owners,
ENTIRE INSTRUCTION MANUAL. employers and users should become familiar with, and
comply with, all applicable OSHA regulations and/or any
applicable Federal, State and Local codes, standards, and
1.1 GENERAL regulations relative to personal protective equipment,
Sullair Corporation and its subsidiaries design and such as eye and face protective equipment, respiratory
manufacture all of their products so they can be operated protective equipment, equipment intended to protect the
safely. However, the responsibility for safe operation rests extremities, protective clothing, protective shields and
with those who use and maintain these products. The barriers and electrical protective equipment, as well as
following safety precautions are offered as a guide which, noise exposure administrative and/or engineering controls
if conscientiously followed, will minimize the possibility of and/or personal hearing protective equipment.
accidents throughout the useful life of this equipment.
The compressor should be operated only by those who 1.3 PRESSURE RELEASE
have been trained and delegated to do so, and who have A. Install an appropriate flow-limiting valve between the
read and understood this Operator's Manual. Failure to service air outlet and the shut-off (throttle) valve, either
follow the instructions, procedures and safety precautions at the compressor or at any other point along the air
in this manual may result in accidents and injuries. line, when an air hose exceeding 1/2" (13mm) inside
NEVER start the compressor unless it is safe to do so. DO diameter is to be connected to the shut-off (throttle)
NOT attempt to operate the compressor with a known valve, to reduce pressure in case of hose failure, per
unsafe condition. Tag the compressor and render it OSHA Standard 29 CFR 1926.302(b)(7) and/or any
inoperative by disconnecting and locking out all power at applicable Federal, State and Local codes, standards
source or otherwise disabling its prime mover so others and regulations.
who may not know of the unsafe condition cannot attempt B. When the hose is to be used to supply a manifold,
to operate it until the condition is corrected. install an additional appropriate flow-limiting valve
between the manifold and each air hose exceeding
Install, use and operate the compressor only in full 1/2" (13mm) inside diameter that is to be connected
compliance with all pertinent OSHA regulations and/or any to the manifold to reduce pressure in case of hose
applicable Federal, State, and Local codes, standards and failure.
regulations.
C. Provide an appropriate flow-limiting valve at the
DO NOT modify the compressor and/or controls in any beginning of each additional 75 feet (23m) of hose in
way except with written factory approval. runs of air hose exceeding 1/2" (13mm) inside
diameter to reduce pressure in case of hose failure.
® SULLAIR ®
3000-4500 Operator’s Manual and Parts List 1
SECTION 1
D. Flow-limiting valves are listed by pipe size and flow- D. Disconnect and lock out all power at source prior to
rated. Select appropriate valves accordingly, in attempting any repairs or cleaning of the compressor
accordance with their manufacturer's or of the inside of the enclosure, if any.
recommendations. E. Keep electrical wiring, including all terminals and
E. DO NOT use air tools that are rated below the pressure connectors in good condition. Replace any
maximum rating of the compressor. Select air tools, wiring that has cracked, cut, abraded or otherwise
air hoses, pipes, valves, filters and other fittings degraded insulation, or terminals that are worn,
accordingly. DO NOT exceed manufacturer's rated discolored or corroded. Keep all terminals and
safe operating pressures for these items. pressure connectors clean and tight.
F. Secure all hose connections by wire, chain or other F. Keep grounded and/or conductive objects such as
suitable retaining device to prevent tools or hose ends tools away from exposed live electrical parts such as
from being accidentally disconnected and expelled. terminals to avoid arcing which might serve as a
G. Open fluid filler cap only when compressor is not source of ignition.
running and is not pressurized. Shut down the G. Remove any acoustical material or other material that
compressor and bleed the receiver tank to zero may be damaged by heat or that may support
internal pressure before removing the cap. combustion and is in close proximity, prior to
H. Vent all internal pressure prior to opening any line, attempting weld repairs.
fitting, hose, valve, drain plug, connection or other H. Keep suitable fully charged Class BC or ABC fire
component, such as filters and line oilers, and before extinguisher or extinguishers nearby when servicing
attempting to refill optional air line anti-icer systems and operating the compressor.
with antifreeze compound. I. Keep oily rags, trash, leaves, litter or other
I. Keep personnel out of line with and away from the combustibles out of and away from the compressor.
discharge opening of hoses or tools or other points of J. DO NOT operate the compressor without proper flow
compressed air discharge. of cooling air or water or with inadequate flow of
J. DO NOT use air at pressures higher than 2.1 bar for lubricant or with degraded lubricant.
cleaning purposes, and then only with effective chip K. DO NOT attempt to operate the compressor in any
guarding and personal protective equipment per classification of hazardous environment unless the
OSHA Standard 29 CFR 1910.242 (b) and/or any compressor has been specially designed and
applicable Federal, State, and Local codes, standards manufactured for that duty.
and regulations.
K. DO NOT engage in horseplay with air hoses as death 1.5 MOVING PARTS
or serious injury may result.
A. Keep hands, arms and other parts of the body and also
1.4 FIRE AND EXPLOSION clothing away from couplings, fans and other moving
parts.
A. Clean up spills of lubricant or other combustible B. DO NOT attempt to operate the compressor with the
substances immediately, if such spills occur. fan, coupling or other guards removed.
B. Shut off the compressor and allow it to cool. Then keep C. Wear snug-fitting clothing and confine long hair when
sparks, flames and other sources of ignition away and working around this compressor, especially when
DO NOT permit smoking in the vicinity when checking exposed to hot or moving parts.
or adding lubricant or when refilling air line anti-icer
systems with antifreeze compound. D. Keep access doors, if any, closed except when
making repairs or adjustments.
C. DO NOT permit fluids, including air line anti-icer
system antifreeze compound or fluid film, to E. Make sure all personnel are out of and/or clear of the
accumulate on, under or around acoustical material, compressor prior to attempting to start or operate it.
or on any external surfaces of the air compressor. F. Disconnect and lock out all power at source and verify
Wipe down using an aqueous industrial cleaner or at the compressor that all circuits are de-energized to
steam clean as required. If necessary, remove minimize the possibility of accidental start-up, or
acoustical material, clean all surfaces and then operation, prior to attempting repairs or adjustments.
replace acoustical material. Any acoustical material This is especially important when compressors are
with a protective covering that has been torn or remotely controlled.
punctured should be replaced immediately to prevent G. Keep hands, feet, floors, controls and walking
accumulation of liquids or fluid film within the material. surfaces clean and free of fluid, water or other liquids
DO NOT use flammable solvents for cleaning to minimize the possibility of slips and falls.
purposes.
2 3000-4500 Operator’s Manual and Parts List

® SULLAIR ®
SAFETY
1.6 HOT SURFACES, SHARP EDGES G. If air line anti-icer system antifreeze compound enters
the eyes or if fumes irritate the eyes, they should be
AND SHARP CORNERS washed with large quantities of clean water for fifteen
minutes. A physician, preferably an eye specialist,
A. Avoid bodily contact with hot fluid, hot coolant, hot should be contacted immediately.
surfaces and sharp edges and corners.
H. DO NOT store air line anti-icer system antifreeze
B. Keep all parts of the body away from all points of air compound in confined areas.
discharge.
I. The antifreeze compound used in air line antifreeze
C. Wear personal protective equipment including gloves systems contains methanol and is toxic, harmful or
and head covering when working in, on or around the fatal if swallowed. Avoid contact with the skin or eyes
compressor. and avoid breathing the fumes. If swallowed, induce
D. Keep a first aid kit handy. Seek medical assistance vomiting by administering a tablespoon of salt, in each
promptly in case of injury. DO NOT ignore small cuts glass of clean, warm water until vomit is clear, then
and burns as they may lead to infection. administer two teaspoons of baking soda in a glass of
clean water. Have patient lay down and cover eyes to
1.7 TOXIC AND IRRITATING exclude light. Call a physician immediately.
SUBSTANCES 1.8 ELECTRICAL SHOCK

A. DO NOT use air from this compressor for
A. This compressor should be installed and maintained
respiration (breathing) except in full compliance with
in full compliance with all applicable Federal, State
OSHA Standards 29 CFR 1910 and/or any applicable
and Local codes, standards and regulations, including
Federal, State or Local codes or regulations.
those of the National Electrical Code, and also
including those relative to equipment grounding
DANGER conductors, and only by personnel that are trained,
qualified and delegated to do so.
B. Keep all parts of the body and any hand-held tools or
other conductive objects away from exposed live parts
of electrical system. Maintain dry footing, stand on
insulating surfaces and DO NOT contact any other
portion of the compressor when making adjustments
INHALATION HAZARD! or repairs to exposed live parts of the electrical
system. Make all such adjustments or repairs with one
Death or serious injury can result from hand only, so as to minimize the possibility of creating
inhaling compressed air without a current path through the heart.
using proper safety equipment. See C. Attempt repairs in clean, dry and well lighted and
OSHA standards and/or any ventilated areas only.
applicable Federal, State, and Local
codes, standards and regulations on D. DO NOT leave the compressor unattended with open
safety equipment. electrical enclosures. If necessary to do so, then
disconnect, lock out and tag all power at source so
B. DO NOT use air line anti-icer systems in air lines others will not inadvertently restore power.
supplying respirators or other breathing air utilization
equipment and DO NOT discharge air from these
systems into unventilated or other confined areas.
C. Operate the compressor only in open or adequately
ventilated areas.
D. Locate the compressor or provide a remote inlet so
that it is not likely to ingest exhaust fumes or other
toxic, noxious or corrosive fumes or substances.
E. Coolants and lubricants used in this compressor are
typical of the industry. Care should be taken to avoid
accidental ingestion and/or skin contact. In the event
of ingestion, seek medical treatment promptly. Wash
with soap and water in the event of skin contact.
Consult Material Safety Data Sheet for information
pertaining to fluid of fill.
F. Wear goggles or a full face shield when adding
antifreeze compound to air line anti-icer systems.
® SULLAIR ®
SECTION 1
E. Disconnect, lock out, and tag all power at source prior K. When moving the compressor by forklift truck, utilize
to attempting repairs or adjustments to rotating fork pockets if provided. Otherwise, utilize pallet if
machinery and prior to handling any ungrounded provided. If neither fork pockets or pallet are provided,
conductors. then make sure compressor is secure and well
balanced on forks before attempting to raise or
DANGER transport it any significant distance.
L. Make sure forklift truck forks are fully engaged and
All field equipment must be tested for tipped back prior to lifting or transporting the
electrostatic fields prior to servicing compressor.
or making contact with the machine
using the following or equivalent test M. Forklift no higher than necessary to clear obstacles at
equipment: floor level and transport and corner at minimum
practical speeds.
• 90-600 VAC: Volt detector such as
Fluke Model 1AC-A N. Make sure pallet-mounted compressors are firmly
• 600-7000 VAC: Voltage detector bolted or otherwise secured to the pallet prior to
such as Fluke Networks Model attempting to forklift or transport them. NEVER
C9970 attempt to forklift a compressor that is not secured to
its pallet, as uneven floors or sudden stops may cause
It is the responsibility of each the compressor to tumble off, possibly causing
organization to provide/arrange serious injury or property damage in the process.
training for all their associates
expected to test for electrostatic 1.10 ENTRAPMENT
fields.
A. If the compressor enclosure, if any, is large enough to
hold a man and if it is necessary to enter it to perform
1.9 LIFTING service adjustments, inform other personnel before
doing so, or else secure and tag the access door in
A. If the compressor is provided with a lifting bail, then lift
the open position to avoid the possibility of others
by the bail provided. If no bail is provided, then lift by
closing and possibly latching the door with personnel
sling. Compressors to be air-lifted by helicopter must
inside.
not be supported by the lifting bail but by slings
instead. In any event, lift and/or handle only in full B. Make sure all personnel are out of compressor before
compliance with OSHA standards 29 CFR 1910 closing and latching enclosure doors.
subpart N and/or any applicable Federal, State, and
Local codes, standards and regulations.
B. Inspect points of attachment for cracked welds and for
cracked, bent, corroded or otherwise degraded
members and for loose bolts or nuts prior to lifting.
C. Make sure entire lifting, rigging and supporting
structure has been inspected, is in good condition and
has a rated capacity of at least the weight of the
compressor. If you are unsure of the weight, then
weigh compressor before lifting.
D. Make sure lifting hook has a functional safety latch or
equivalent, and is fully engaged and latched on the
bail or slings.
E. Use guide ropes or equivalent to prevent twisting or
swinging of the compressor once it has been lifted
clear of the ground.
F. DO NOT attempt to lift in high winds.
G. Keep all personnel out from under and away from the
compressor whenever it is suspended.
H. Lift compressor no higher than necessary.
I. Keep lift operator in constant attendance whenever
compressor is suspended.
J. Set compressor down only on a level surface capable
of safely supporting at least its weight and its loading
unit.

® SULLAIR ®
® SULLAIR ®
Section 2
DESCRIPTION
2.1 INTRODUCTION
Your new Sullair flood-lubricated rotary screw air
compressor will provide you with a unique experience in
improved reliability and simplified maintenance.
Compared to other types of compressors, the Sullair rotary
screw is unique in mechanical reliability, with "no wear"
and "no inspection" required of the working parts within the
compressor unit.
Read MAINTENANCE on page 61 to see how
surprisingly easy it is to keep your air compressor in top
operating condition.
® SULLAIR ®
SECTION 2
11
10
1
6
7 3
8
1
5
9
2
4
12 13
5 2
02250155-601 2_1
1. Fluid Filter 8. E-Stop Button

2. Moisture Separator 9. Compressor Unit
3. Receiver Tank 10. Cooler Fan Motor
4. Fluid Fill 11. Cooler
5. Fluid Fill Sight Glass 12. Motor
6. Starter Box 13. Air Inlet Filter
7. WS Controller
Figure 2-1: Overall Component Layout, Air-Cooled Model

® SULLAIR ®
DESCRIPTION
11 14
14 11 2
10
10 10
6
2
7
1
8
12
3 9
4
5 4 5
12 13 3
02250155-601_2_2
1. Moisture Separator 8. E-Stop Button

2. Fluid Filter 9. Compressor Unit
3. Receiver Tank 10. Oil Cooler
4. Fluid Fill 11. Aftercooler
5. Fluid Fill Sight Glass 12. Motor
6. Starter Box 13. Air Inlet Filter
7. WS Controller 14. Canopy Vent Fan
Figure 2-2: Overall Component Layout, Water-Cooled Model
® SULLAIR ®
SECTION 2
2.2 DESCRIPTION OF COMPONENTS The 3000-4500 Series compressors are factory-filled with
Sullube lubricant. For more information on fluid fill, consult
Refer to Figure 2-1 and Figure 2-2. The components and SPECIFICATIONS on page 17.
assemblies of the air compressor are clearly shown. The
complete package includes compressor, electric motor, Sullair 24KT compressors are filled with a fluid that rarely
starter, compressor inlet system, compressor discharge needs to be changed. Use only Sullair 24KT fluid in the
system, compressor lubrication and cooling system, event that a fluid change is required.
capacity control system, WS Controller, aftercooler, a
combination separator and trap, all mounted on a heavy CAUTION
gauge steel frame.
Mixing of other lubricants within the
On air-cooled models, a fan draws air into the enclosure compressor unit will void all
over the fan and main motors through the combined warranties.
aftercooler and fluid cooler thereby removing the
compression heat from the compressed air and the
cooling fluid, and forces it out the top of the machine. Sullair recommends that a 24KT sample be taken at the
first filter change and sent to the factory for analysis. This
On water-cooled models, a shell and tube heat exchanger is a free service. The sample kit with instructions and self-
is mounted on the compressor frame. Fluid is piped into addressed container is to be supplied by your Sullair
the heat exchanger where compression heat is removed dealer at start-up. The user will receive an analysis report
from the fluid. Another similar heat exchanger cools the with recommendations.
compressed air.
Fluid is injected into the compressor unit hoses and mixes
Both air-cooled and water-cooled versions have easily directly with the air as the rotors turn, compressing the air.
accessible items such as the fluid filter air/oil separator and The fluid flow has three basic functions:
control valves. The inlet air filter is also easily accessible 1. As coolant, it controls the rise of air temperature
for servicing. normally associated with the heat of compression.
2. Seals the clearance paths between the rotors and the
2.3 SULLAIR COMPRESSOR UNIT, stator and also between the rotors themselves.
FUNCTIONAL DESCRIPTION 3. Acts as a lubricating film between the rotors allowing
Sullair air compressors feature the Sullair compressor unit, one rotor to directly drive the other, which is an idler.
a single-stage, positive displacement, flood lubricated- After the air/fluid mixture is discharged from the
type compressor. This unit provides continuous compressor unit, the fluid is separated from the air. At
compression to meet your needs. this time, the air flows through an aftercooler and
separator then to your service line while the fluid is
NOTE being cooled in preparation for reinjection.
With a Sullair compressor, there is no

maintenance or inspection of the
internal parts of the compressor unit
permitted in accordance with the
terms of the warranty.

® SULLAIR ®
DESCRIPTION
COOLING / LUBRICATION
SYSTEM
Fluid line
Fluid line
AIR
FLUID/AIR
FLUID
DISCHARGE SYSTEM
02250155-601_2_3
Figure 2-3: Air-Cooled, Cooling / Lubrication and Discharge System
® SULLAIR ®
SECTION 2
COOLING / LUBRICATION
SYSTEM
AIR
FLUID/AIR
FLUID
DISCHARGE SYSTEM
02250155-601 2_4
Figure 2-4: Water-Cooled, Cooling / Lubrication and Discharge System

® SULLAIR ®
DESCRIPTION
2.4 COMPRESSOR COOLING AND The compressed air/fluid mixture enters the receiver tank
and flows through an internal baffle system. The direction
LUBRICATION SYSTEM, of movement is changed and its velocity significantly
reduced, thus causing large droplets of fluid to form and
FUNCTIONAL DESCRIPTION fall to the bottom of the receiver tank. The fractional
Refer to Figure 2-3 or Figure 2-4. The Cooling and percentage of fluid remaining in the compressed air
Lubrication System (air-cooled version) consists of a fan, collects on the surface of the separator element as the
fan motor, radiator-type aftercooler/fluid cooler, full flow compressed air flows through the separator. A return line
fluid filter, thermal valve, and interconnecting hoses. For (or scavenge tube) leads from the bottom of the separator
water-cooled models, two shell and tube heat exchangers element to a medium pressure region of the compressor
are substituted for the radiator-type cooler listed above. unit. Fluid collecting on the bottom of the separator is
The pressure in the receiver tank causes fluid flow by returned to the compressor by a pressure differential
forcing the fluid from the high pressure area of the receiver between the receiver and the compressor. A visual sight
tank to an area of lower pressure in the compressor unit. glass is located on the return line to observe this fluid flow.
There is also an orifice in this return line (protected by a
Fluid flows from the bottom of the receiver tank to the strainer) to assure proper flow. The separator system
thermal valve. The thermal valve is fully open when the reduces the fluid carry-over to less than 1 ppm (parts per
fluid temperature is below 185˚F (85˚C) [200˚F (93˚C) for million). A message on the WS Controller indicates if
24KT] and pressures are rated above 150 psig. The fluid abnormal pressure drop through the separator develops.
passes through the thermal valve, the main filter and Refer to
directly to the compressor unit where it lubricates, cools Lubrication Change Recommendations and
and seals the rotors and the compression chamber. Maintenance, Fluid Filter and Separator on page 21.
As the discharge temperature rises above 185˚F (85˚C), A minimum pressure/check valve, located downstream
due to the heat of compression, the thermal valve begins from the separator, assures a minimum receiver pressure
to close and a portion of the fluid then flows through the of 50 psig (3.4 bar) during loaded conditions. This
cooler. From the cooler the fluid flows to the fluid filter and pressure is necessary for proper air/fluid separation and
then on to the compressor unit. proper fluid circulation.
A portion of the fluid flowing to the compressor is routed to A terminal check valve is incorporated into the minimum
the anti-friction bearings which support the rotors inside pressure/check valve to prevent compressed air in the
the compressor unit. service line from bleeding back into the receiver on
The fluid filter has a replacement element and an integral shutdown and during operation of the compressor in an
pressure bypass valve. Refer to unloaded condition.
Lubrication Change Recommendations and A pressure relief valve (located on the wet side of the
Maintenance, Fluid Filter and Separator on page 21. separator) is set to open if the receiver tank pressure
Water-cooled models have a water pressure switch to exceeds the receiver tank rating. The WS Controller will
prevent operation with inadequate water pressure. shut down the compressor if the discharge temperature
reaches 235˚F (113˚C).
2.5 COMPRESSOR DISCHARGE WARNING
SYSTEM, FUNCTIONAL
DO NOT remove caps, plugs, and/or
DESCRIPTION other components when compressor
Refer to Figure 2-3 or Figure 2-4. The compressor unit is running or pressurized.
discharges the compressed air/fluid mixture into the Stop compressor and relieve all
combination receiver tank. internal pressure before doing so.
The receiver has three basic functions:
1. It acts as a primary fluid separator. Fluid is added to the receiver tank via a capped fluid filler
opening, placed low on the tank to prevent overfilling of the
2. Serves as the compressor fluid sump. receiver tank. A sight glass enables the operator to visually
3. Houses the final fluid separator. monitor the receiver tank fluid level.
® SULLAIR ®
SECTION 2
2.6 CONTROL SYSTEM, Start Mode - 0 to 50 PSIG (0 to 3.5 Bar)

FUNCTIONAL DESCRIPTION When the compressor " " (START) pad is depressed,
the receiver tank pressure will quickly rise from 0 to 50 psig
Refer to Figure 2-5 and Figure 2-6. The purpose of the (0 - 3.4 bar). The compressor initially starts unloaded with
compressor control system is to regulate the amount of air the solenoid valve open and the inlet valve closed. It then
being compressed to match the amount of compressed air switches to full load when full rpm has been achieved.
being used. The capacity control system consists of a During this period, both the pressure regulator and the
solenoid valve, regulator valve and an inlet valve. The solenoid valve are closed, the inlet valve is fully open and
functional description of the control system is described the compressor pumps at full rated capacity. The rising
below in four distinct phases of operation. For explanatory compressor air pressure is isolated from the service line
purposes, this description will apply to a compressor with in this phase by the minimum pressure valve set at
an operating range of 100 to 110 psig (6.9 to 7.6 bar). A approximately 50 psig (3.4 bar).
compressor with any other pressure range would operate
in the same manner except stated pressures.
2 8 9
6
5
7
4
SU_0000007
1. Air Outlet 6. Minimum Pressure/Check Valve

2. Unload Solenoid Valve 7. Receiver Tank
3. Pressure Regulator 8. Sequencing Solenoid Valve
4. Air Inlet 9. WS Controller
5. Blowdown Valve
Figure 2-5: Standard Sequencing Control System

® SULLAIR ®
DESCRIPTION
Full Load Mode - 50 to 100 to the atmosphere, located in the compressor receiver
tank, reducing the receiver tank pressure to approximately
PSIG (3.4 to 6.9 BAR) 17 psig (1.2 bar). The check valve in the air service line
When the compressed air pressure rises above 50 psig prevents line pressure from returning to the receiver tank.
(3.4 bar), the minimum pressure valve opens allowing
compressed air to flow into the service line. From this point When the line pressure drops to the low setting (cut-in
on, the line air pressure is continually monitored by the WS pressure; usually 100 psig (6.9 bar) on low pressure (7 bar)
Controller. The pressure regulator and the solenoid valve compressors and 125 psig (8.6 bar) on high pressure (9
remain closed during this phase. The inlet valve is in the bar) compressors, 150 psig (10.3 bar) on (10 bar)
fully open position as long as the compressor is running at compressors, 175 psig (12.0 bar) on (12 bar)
100 psig (6.9 bar) or below. compressors), the WS Controller energizes the solenoid
valve and allows the blowdown valve to close. The re-
Modulating Mode - 100 to 110 energized solenoid valve again prevents line pressure
from reaching the inlet control valve. Should the pressure
PSIG (6.9 to 7.6 BAR) begin to rise, the pressure regulator will resume its normal
If less than the rated capacity of compressed air is being function as previously described.
used, the service line pressure will rise above 100 psig
(6.9 bar). The pressure regulator valve gradually opens, Load / No Load Control
directing air pressure to the inlet control valve, reducing air If desired by the customer, the compressor can be set to
entering the compressor until it matches the amount of air operate load/no load without modulating control. This
being used. The control system functions continually in control mode is often selected when a large amount of
this manner between the limits of 100 to 110 psig (6.9 to compressed air storage (air tank) is available. Using the
7.6 bar) in response to varying demands from the service WS Controller keypad, select "load/no load control" from
line. the menu. On a machine rated for 100 psig (7 bar) the
The integrated inlet valve has an orifice which vents a small compressor will run in the full load mode up to 100 psig (7
amount of air to the compressor inlet when the pressure bar). If less than the rated capacity is required, pressure
regulator controls the inlet control valve. The orifice also will rise above 100 psig and the WS Controller will de-
bleeds any accumulated moisture from the control lines. energize the solenoid valve, causing the compressor to
run in the unload mode. When the system pressure falls to
Unload Mode- In Excess of 110 90 psig (6.3 bar), the WS Controller energizes the solenoid
valve, causing the compressor to return to the full load
PSIG (7.6 BAR) mode. The compressor will thus operate to keep the
When a relatively small amount or no air is being used, the system pressure in the range of 90-100 psig (6.3 - 6.9 bar).
service line pressure continues to rise. When it exceeds
110 psig (7.6 bar), the WS Controller control system de- Automatic Operation
energizes the solenoid valve allowing receiver tank air For applications with varied periods of time when there are
pressure to be supplied directly to close the inlet valve. no air requirements, the WS Controller's AUTOMATIC
Simultaneously, the solenoid valve sends a pneumatic mode allows the compressor to shutdown (time delayed)
signal to the blowdown valve. The blowdown valve opens when no compressed air requirement is present and
restart as compressed air is needed.
® SULLAIR ®
SECTION 2
2.7 AIR INLET SYSTEM, WARNING

FUNCTIONAL DESCRIPTION "The Plastic Pipe Institute
Refer to Figure 2-6. The compressor inlet system consists recommends against the use of
of a dry-type air filter, a restriction gauge and an air inlet thermoplastic pipe to transport
valve. compressed air or other compressed
The restriction gauge (located on the air filter) indicates the gases in exposed above ground
condition of the air filter by showing red when filter locations, e.g. in exposed plant
maintenance is required. piping." (I)
The poppet-type modulating air inlet valve directly controls Sullube should not be used with PVC
the amount of air intake to the compressor in response to piping systems. It may affect the bond
the operation of the pressure regulator. Refer to at cemented joints. Certain other
Full Load Mode - 50 to 100 PSIG (3.4 to 6.9 BAR) plastic materials may also be affected.
on page 13. The inlet valve also acts as a check valve, thus (I) Plastic Pipe Institute,
preventing reverse rotation when the compressor is shut Recommendation B, Adopted
down.
January 19, 1972.

® SULLAIR ®
DESCRIPTION
1
2
5
3 4
SU_0000008
1. Air Inlet Filter 4. Receiver Tank

2. Air Inlet 5. Restriction Indicator
3. Compressor Unit
Figure 2-6: Air Inlet System
® SULLAIR ®
SECTION 2

® SULLAIR ®
® SULLAIR ®
Section 3
SPECIFICATIONS
3.1 TABLE OF SPECIFICATIONS - 3000, 3000P, 3700 AND 4500 SERIES
MODELS
DIMENSIONS
Length Width Height Weight Weight
MODEL (I) HP
lbs kg
in mm in mm in mm
ODP TEFC ODP TEFC
3000 SERIES
3007 40 62.0 1575 34.5 876 61.5 1562 1818 1884 825 855
3009 40 62.0 1575 34.5 876 61.5 1562 1818 1884 825 855
3010 40 62.0 1575 34.5 876 61.5 1562 1818 1884 825 855
3000P SERIES
3007P 40 62.0 1575 34.5 876 61.5 1562 1993 2059 904 934
3009P 40 62.0 1575 34.5 876 61.5 1562 1993 2059 904 934
3010P 40 62.0 1575 34.5 876 61.5 1562 1993 2059 904 934
3700 SERIES
3707 50 62.0 1575 34.5 876 61.5 1562 2043 2127 927 965
3709 50 62.0 1575 34.5 876 61.5 1562 2043 2127 927 965
3710 50 62.0 1575 34.5 876 61.5 1562 2043 2127 927 965
3712 50 62.0 1575 34.5 876 61.5 1562 2043 2127 927 965
4500 SERIES
4509 60 62.0 1575 34.5 876 61.5 1562 2193 2270 995 1030
4510 60 62.0 1575 34.5 876 61.5 1562 2193 2270 995 1030
4512 60 62.0 1575 34.5 876 61.5 1562 2193 2270 995 1030

(I) Includes standard and 24KT. Rated pressure designations appearing after model number are as follows:
07 - 100 psig (6.9 bar) 10 - 150 psig (10.3 bar)
09 - 125 psig (8.6 bar) 12 - 175 psig (12 bar)
Maximum pressure is rated pressure plus 10 psig (0.7 bar).
® SULLAIR ®
SECTION 3
3.2 TABLE OF SPECIFICATIONS - VARIABLE SPEED DRIVE MODELS

VSD SERIES (I) - 3000 (MODELS 3007 THROUGH 3010)
MOTOR ODP TEFC
HZ / VOLTAGE 460/60 575/60 400/50 460/60 575/60 400/50
DRIVE AMP RATING 72 52 87 72 52 87
WEIGHT (lbs / kg) 1894 / 859 1894 / 859 1894 / 859 1960 / 889 1960 / 889 1960 / 889
LENGTH (in / mm) 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575
WIDTH (in / mm) 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876
HEIGHT (in / mm) 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562
VSD SERIES (I) - 3000P (MODELS 3007 THROUGH 3010)
MOTOR ODP TEFC
HZ / VOLTAGE 460/60 575/60 400/50 460/60 575/60 400/50
WEIGHT (lbs / kg) 2069 / 938 2069 / 938 2069 / 938 2135 / 968 2135 / 968 2135 / 968
LENGTH (in / mm) 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575
WIDTH (in / mm) 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876
HEIGHT (in / mm) 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562
MOTOR ODP TEFC
HZ / VOLTAGE 460/60 575/60 400/50 460/60 575/60 400/50
WEIGHT (lbs / kg) 2119 / 961 2171 / 984 2119 / 961 2203 / 999 2255 / 1023 2203 / 999
LENGTH (in / mm) 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575
WIDTH (in / mm) 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876
HEIGHT (in / mm) 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562
MOTOR ODP TEFC
HZ / VOLTAGE 460/60 575/60 400/50 460/60 575/60 400/50
WEIGHT (lbs / kg) 2361 / 1071 2244 / 1018 2361 / 1071 2438 / 1106 2296 / 1041 2438 / 1106
LENGTH (in / mm) 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575 62.0 / 1575
WIDTH (in / mm) 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876 34.5 / 876
HEIGHT (in / mm) 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562 61.5 / 1562

(I) Includes standard and 24KT. Rated pressure designations appearing after model number are as follows:
07 - 100 psig (6.9 bar) 10 - 150 psig (10.3 bar)
09 - 125 psig (8.6 bar) 12 - 175 psig (12 bar)
Maximum pressure is rated pressure plus 10 psig (0.7 bar).

® SULLAIR ®
SPECIFICATIONS
3.3 COMPRESSOR SPECIFICATIONS

COMPRESSOR: STANDARD MODELS:
Type: Rotary Screw
Standard Operating Pressure: 100 psig (7 bar) 125 psig (9 bar) 150 psig (10 bar) 175 psig (12 bar)
Bearing Type: Anti-friction
Ambient Temperature (Max.) (II): 104°F (40°C)
Cooling: Pressurized fluid
Compressor Fluid: Sullair Sullube; 24KT is optional
Receiver Capacity: 3.0 gallons (11.4 liters)
Control: WS Controller
(ll) Special compressors are available for operation in higher ambient temperature.
MOTOR (III): STANDARD MODELS:

Size: 40, 50, 60 HP / 30, 37, 45 KW
Type: C-Flanged, Open Drip-proof, Epact Efficiency, Three Phase, 230/460
60Hz, 380-415 (400) 50 Hz
VSD Type: C-Flanged, Open Drip-proof, Premium Efficiency, Three Phase, 460V
60Hz, 380-415V (400V) 50Hz
Maximum Ambient Temperature 104°F (40°C)
Options Available: 200V and 575V 60 Hz, 220 50 Hz TEFC also available: CE Approved
Starter: Full Voltage Magnetic, Wye-Delta or VSD
Speed - 40, 50, 60 HP: 1780 RPM (60 Hz) or 1475 RPM (50 Hz)
(III) Multi-frequency and voltage motors are used. The compressors must be used only with the specified electrical frequency and voltage.
® SULLAIR ®
SECTION 3
3.4 LUBRICATION GUIDE NOTE

Refer to Figure 3-1 for location of fluid fill port. For best Flush system when switching
value and longest uninterrupted service, the 3000-4500
lubricant brands.
Series compressors are factory filled and tested with
Sullube lubricant.
When ambient conditions exceed those noted or if
CAUTION conditions warrant use of "extended" life lubricants contact
Sullair for recommendation.
compressor unit will void all
warranties.
If fluid change is required, follow Section 3.6,

Lubrication Change Recommendations and
Maintenance, Fluid Filter and Separator on page 21.
4
WARNING
"The Plastic Pipe Institute 1
recommends against the use of
thermoplastic pipe to transport
compressed air or other compressed 2
gases in exposed above ground
locations, e.g. in exposed plant
piping." (I)
3
Sullube should not be used with PVC
piping systems. It may affect the bond SA_0000013
at cemented joints. Certain other 1. Fluid Fill Port

plastic materials may also be affected. 2. Sight Glass
(I) Plastic Pipe Institute, 3. Fluid Drain Valve
Recommendation B, Adopted 4. Receiver Tank
January 19, 1972. Figure 3-1: Fluid Fill Location
Maintenance of all other components is still recommended
as indicated in the Operator’s Manual. 3.5 APPLICATION GUIDE
DO NOT MIX DIFFERENT TYPES OF FLUIDS. Sullair encourages the user to participate in a fluid analysis
Contamination of compressor fluid with mineral oil or other program with the fluid suppliers. This could result in a fluid
fluids may lead to operational problems such as foaming, change interval differing from that stated in the manual.
filter plugging, orifice or line plugging. Contact your Sullair dealer for details.

® SULLAIR ®
SPECIFICATIONS
3.6 LUBRICATION CHANGE RECOMMENDATIONS AND MAINTENANCE, FLUID

FILTER AND SEPARATOR
LUBRICANT FLUID CHANGE FLUID FILTER CHANGE SEPARATOR CHANGE
Sullube A, E G, C A, D
SRF 1/4000 B, E G, C B, D
24KT F, E G, C A, D
CP-4600-32-F B, E G, C B, D
A - 8,000 hours or once a year.
B - 4,000 hours or more frequently if conditions so require.
C - When measured pressure loss exceeds 20 psig (1.3 bar).
D - When measured pressure loss exceeds 10 psig (0.7 bar).
E - When required by fluid analysis or known contamination.
F - Does not require replacement during normal service conditions.
G - Every 2,000 hours.
® SULLAIR ®
SECTION 3
3.7 IDENTIFICATION, AIR-COOLED, STANDARD AND VSD
2
3
02250156_213r03-2

® SULLAIR ®
SPECIFICATIONS
4
10
9
8
02250156_213r03-1
1. Alternate Incoming Power Supply Location 6. Air Inlet

Dia. 2.5 in. (63.5mm) 7. Containment Pan Drain 1/2"-1/4" NPT
2. WS Controller 8. Incoming Customer Power Supply Location
3. E-Stop 2.5 in. (63.5mm)
4. Oil Level Sight Glass 9. Moisture Drain Connection 1/2"-1/4" NPT
5. Air Exhaust 10. Air Outlet Connection 1 1/2"-11 1/2" NPT
Figure 3-2: Identification, Air-Cooled, Standard and VSD
® SULLAIR ®
SECTION 3
3.8 IDENTIFICATION, WATER-COOLED
2
3
02250160_729r02-2

® SULLAIR ®
SPECIFICATIONS
10
8
9
11
12
4
02250160_729r02-1
1. Alternate Incoming Power Supply Location 7. Containment Pan Drain 1/2"-1/4" NPT
Dia. 2.5 in. (63.5mm) 8. Incoming Customer Power Supply Location
2. WS Controller 2.5 in. (63.5mm)
3. E-Stop 9. Moisture Drain Connection 1/2"-1/4" NPT
4. Oil Level Sight Glass 10. Air Outlet Connection 1 1/2"-11 1/2" NPT
5. Air Exhaust 11. Cooling Water Out 3/4"-14 NPT
6. Air Inlet 12. Cooling Water In 3/4"-14 NPT
Figure 3-3: Identification, Water-Cooled
® SULLAIR ®
SECTION 3
3.9 PIPING AND INSTRUMENTATION, AIR-COOLED

A1
A1 C5
A1 B3
A3
C1
A2
A3
B1 B2
A3 C5
B7
A2
C3
A4
C4
B5
B6
B4
02250156-203r07
Figure 3-4: Piping and Instrumentation, Air-Cooled

® SULLAIR ®
SPECIFICATIONS
Key Description Part Number Note Quantity

1 filter, air 9" plastic 02250127-683 1
2 indicator, restriction 02250003-869 1
3 inlet – (I) 1
4 compressor unit – (I) 1
5 motor – (I) 1
6 filter, coreless 1-1/16 sae 02250155-708 1
7 cooler, air/oil 50 hp 02250151-493 (I) 1
cooler, air/oil 60hp 02250152-862 (I) 1
8 valve, thermal 195 deg 1-1/2"-18 02250092-081 (I) 1
valve, thermal 210 deg 1-1/2"-18 0250148-796 (I) 1
9 orifice, 1/8 x 1/32 02250125-774 1
10 gls, sight/orf sae 02250126-129 1
11 filter, assy genisis 02250117-782 1
12 plug, sightglass 1-5/16" sae 02250097-610 1
13 probe, thermister 3000 ohm 02250155-175 1
14 valve, relief 1/2" 250006-938 1
15 xducr, 1-250# radiometric 02250155-174 2
16 valve, shuttle 1/4" double chk 408893 1
17 vlv, min pressure 1-7/8 sae 02250097-598 1
18 valve, blowdown 1/2" 1.8;1 02250100-042 1
19 sep, wtr scws-235n 1-1/2" l/ad 02250166-734 1
20 elem, sep round 5.5d x 14.3lng 02250160-774 1
21 valve, ball 1/4" 47115 1
22 strainer, v-type 300psi x 1/4 241771 2
23 vlv, sol 3wno 1/4 250# 24vdc 02250155-714 (III) 1
24 valve, pressure reg 250017-280 1
25 tank, separator 02250149-624 1
26 orifice, .140 x 1/4m x 1/4f 02250161-433 1
27 vlv, sol 2wnc 1/4 200# 24vdc 02250155-715 1
28 vlv, chk 1/4" nptf brass viton 02250115-272 1
29 vlv, sol ees 02250125-673 (II) 1
® SULLAIR ®
SECTION 3
3.9 PIPING AND INSTRUMENTATION, AIR-COOLED (CONTINUED)

A1
A1 C5
A1 B3
A3
C1
A2
A3
B1 B2
A3 C5
B7
A2
C3
A4
C4
B5
B6
B4
02250156-203r07
Figure 3-5: Piping and Instrumentation, Air-Cooled

® SULLAIR ®
SPECIFICATIONS

(I) Part varies by model.
(II) Used with EES option.
(III) Two solenoid valves are required with Sequencing option. Refer to B4.

A1 Tank pressure - blue color
A2 Reg pressure - yellow color
A3 Unload pressure - red color
A4 Water drain - clear color

B1 P1 - Wet sump pressure
B2 P2 - Line pressure
B3 SOL 1 - Load/unload solenoid valve
B4 SOL 4 - MEC/sequencing/full load solenoid valve
B5 SOL 5 - Electric drain/scd drain solenoid valve
B6 SOL 7 - EES solenoid valve (optional)
A to open inside EES damper (winter).
B to open outside EES damper (summer).
B7 T1 - Wet discharge temperature

C1 1/2" Hose.
C2 Control moisture drain lines are 1/4" tubing except as noted.
C3 1 1/2" - 11 1/2 npt air outlet.
C4 1/4"-18 npt moisture drain connection.
C5 Section between lettered points (A) and (B) are to be replaced with corresponding option pictured below, as
required by face of order. Refer to B4.
C6 Optional heat trace is applied only to control and moisture drain lines and used only with stainless steel tubing.
Refer to face of order for heat trace requirements.
® SULLAIR ®
SECTION 3
3.10 PIPING AND INSTRUMENTATION, WATER-COOLED

A1
A1
C5 A1
A3
A2
A3
B1 B2
C5
A3 B7
A2
C3
B5
A4
C4
B8 C7
C5
C8
C5
B6
B9
D1
D2 C2 C6
D3 C2 C6
B5
B11 D4
B4
D5
D6
B10 D7
02250162-393R03
Figure 3-6: Piping and Instrumentation, Water-Cooled

® SULLAIR ®
SPECIFICATIONS

1 filter, air 9" plastic 02250127-683 1
2 indicator, restriction 250003-869 1
3 inlet - (I) 1
4 compressor unit - (I) 1
5 motor - (I) 1
6 filter, coreless 1-1/16" sae 02250155-708 1
7 clr, oil/water 5x36 1-5/16" sae 02250094-744 1
8 valve, thermal 210deg 1-1/2"-18 (24kt or 175 psig) 02250148-796 1
8 valve, thermal 195deg 1-1/2"-18 (sullube) 02250092-081 1
9 orifice, 1/8 x 1/32 02250125-774 1
10 gls, sight/orf sae 02250126-129 1
11 filter, assy genisis 02250117-782 1
12 plug, sightglass 1-5/16" sae 02250097-610 1
13 probe, thermister 3000 ohm 02250155-175 1
14 valve, relief 1/2" 250006-938 1
15 xducr, 1-250# radiometric 02250155-174 2
16 valve, shuttle 1/4" double chk 408893 1
17 vlv, min pressure 1-7/8" sae 02250097-598 1
18 valve, blowdown 1/2" 1.8:1 02250100-042 1
19 sep, wtr scws-235n 1 1/2" l/ad 02250166-734 1
20 elem, sep round 5.5d x 14.3lng 02250160-774 1
21 valve, ball 1/4" 47115 1
22 strainer, v-type 300psi x 1/4 241771 2
23 vlv, sol 3wno 1/4 250# 24vdc 02250155-714 2
24 valve, pressure reg 250017-280 1
25 tank, separator 02250149-624 1
26 orf, 140" .25 fnpt x .25 02250161-433 1
27 vlv, sol 2wnc 1/4 200# 24vdc 02250155-715 1
28 vlv, chk 1/4" nptf brass viton 02250115-272 1
29 ht exch 250017-527 1
30 switch, press no 10 psi 250017-992 1
31 valve, water reg 3/4" 160-230f 47398 1
32 vlv, sol 2wnc 3/4 250# n4 02250125-668 1
33 vlv, ball/stnr comb 1/2f x 1/2m 02250144-842 1
34 drn, electric condensate-scd400 02250130-866 1

(I) Part varies by model.
® SULLAIR ®
SECTION 3
3.10 PIPING AND INSTRUMENTATION, WATER-COOLED (CONTINUED)

A1
A1
C5 A1
A3
A2
A3
B1 B2
C5
A3 B7
A2
C3
B5
A4
C4
B8 C7
C5
C8
C5
B6
B9
D1
D2 C2 C6
D3 C2 C6
B5
B11 D4
B4
D5
D6
B10 D7
02250162-393R03
Figure 3-7: Piping and Instrumentation, Water-Cooled

® SULLAIR ®
SPECIFICATIONS

A1 Tank pressure — blue color
A2 Regulator pressure – yellow color
A3 Unload pressure – red color
A4 Water drain – clear color

B1 P1 – wet sump pressure
B2 P2 – line pressure
B3 SOL 1 – load/unload solenoid valve
B4 SOL 4 – MEC/sequencing/full load solenoid valve
B5 SOL 5 – electric drain/SCD drain solenoid valve
B6 SOL 6 – water solenoid valve
B7 T1 – wet discharge temperature
B8 Water solenoid valve option
B9 Water regulating valve option
B10 Sequencing solenoid option
B11 SCD drain option

C1 ½" hose
C2 Control/moisture drain lines are ¼" tubing except as noted
C3 1 ½" – 11 ½" npt air outlet
C4 ¼"-18 npt moisture drain connection
C5 Sections between lettered points are to be replaced with corresponding option pictured below
C6 Optional head trace is applied only to control and moisture drain lines, and used only with stainless steel tubing
C7 Water inlet ¾"-14 npt
C8 Water outlet ¾"-14 npt

D1 Customer furnished line
D2 Water line
D3 Control line
D4 Fluid line
D5 Air/fluid line
D6 Temperature control probe
D7 Air line
® SULLAIR ®
SECTION 3
3.11 WIRING DIAGRAM, MFV AIR-COOLED
02250156_577R04-1

® SULLAIR ®
SPECIFICATIONS
02250156_577R04-2
Figure 3-8: Wiring Diagram, MFV Air-Cooled
® SULLAIR ®
SECTION 3
3.12 WIRING DIAGRAM, MFV WATER-COOLED
02250161-763R03-1

® SULLAIR ®
SPECIFICATIONS
02250161-763R03-2
Figure 3-9: Wiring Diagram, MFV Water-Cooled
® SULLAIR ®
SECTION 3
3.13 WIRING DIAGRAM, WYE-DELTA AIR-COOLED
02250156_118R03-1

® SULLAIR ®
SPECIFICATIONS
02250156_118R03-2
Figure 3-10: Wiring Diagram, Wye-Delta Air-Cooled
® SULLAIR ®
SECTION 3
3.14 WIRING DIAGRAM, WYE-DELTA WATER-COOLED
02250161_761R02-1

® SULLAIR ®
SPECIFICATIONS
02250161_761R02-2
Figure 3-11: Wiring Diagram, Wye-Delta Water-Cooled
® SULLAIR ®
SECTION 3
3.15 WIRING DIAGRAM, VSD AIR-COOLED
02250156_119r04-2

® SULLAIR ®
SPECIFICATIONS
02250156_119r04-2
Figure 3-12: Wiring Diagram, VSD Air-Cooled
® SULLAIR ®
SECTION 3
3.16 WIRING DIAGRAM, VSD WATER-COOLED
02250161-762R02-1

® SULLAIR ®
SPECIFICATIONS
02250161-762R02-2
Figure 3-13: Wiring Diagram, VSD Water-Cooled
® SULLAIR ®
SECTION 3
3.17 WIRING DIAGRAM, VSD AIR-COOLED, 575V SERIES DELTA
02250164_731r01-1

® SULLAIR ®
SPECIFICATIONS
02250164_731r01-2
Figure 3-14: Wiring Diagram, VSD Air-Cooled, 575V Series Delta
® SULLAIR ®
SECTION 3
3.18 WIRING DIAGRAM, VSD WATER-COOLED, SERIES DELTA 575V
02250164_732r01-1

® SULLAIR ®
SPECIFICATIONS
02250164_732r01-2
Figure 3-15: Wiring Diagram, VSD Water-Cooled, Series Delta 575V
® SULLAIR ®
SECTION 3

® SULLAIR ®
® SULLAIR ®
Section 4
INSTALLATION
4.1 MOUNTING OF COMPRESSOR 4.2 VENTILATION AND COOLING
A suitable foundation or fabricated support must be Air-Cooled Compressors
established to support the compressor. It should be rigid
enough to keep the compressor frame level and maintain • An area with adequate space must be provided for the
alignment of the compressor and motor. Tie-down bolts of compressor and its components. Air-cooled
sufficient size must be used to provide uniform contact compressors require a minimum of 3 feet (1 meter)
between the foundation and the compressor frame. around the perimeter of the compressor.
Materials such as rubber or cork can be used to provide • The location should be free from standing water and
uniform contact between the foundation and compressor allow access to clean air that is free from exhaust and
frame. paint fumes, dust, metal filings or caustic chemicals.
• Piping loads must be eliminated through the use of flex • Cooling air should be removed from the area in order
connectors or other systems which prevent piping to prevent the re-introduction of heated exhaust air
loads from being transmitted to the compressor. back into the compressor’s cooling system.
• Special consideration should be made to meet • Reduced headroom above the compressor will
national and local electrical codes for the required require that cooling air be either ducted or in some way
space around and in front of the electrical panel. deflected away from the compressor. Inadequate
Lighting should be provided for future service ventilation will result in higher ambient operating
requirements. temperatures.
• Accessibility for fork lift trucks, overhead cranes and
maintenance vehicles should be given careful NOTE
consideration in order to provide any maintenance
that may be required. Adequate space around the unit Systems that employ both a
should be provided for access to all components of the conventional reciprocating
compressor. compressor and a screw-type axial
• Softer surfaces in walls or ceilings will absorb sound compressor must be isolated from
and minimize ambient noise levels. Harder, reflective each other by use of a common
surfaces will increase ambient noise levels. receiver tank. Individual airlines from
• Water-cooled compressors must have provisions for each compressor should be piped to
cooling water supply and drainage available. the common receiver tank.
NOTE NOTE
Ambient temperatures above 104˚F
Shipping straps are painted red in
(40˚C) require that the high ambient
order to help identify them for
option is specified for the
removal. Be sure to remove them prior
compressor.
to operation of the drive assembly.
® SULLAIR ®
SECTION 4
Water-Cooled Compressors Table 4-2 Ventilation Requirements on page 53

indicates the minimum ventilation requirements
Adequate cooling water flow must be supplied to water- necessary to keep the compressor running at its normal
cooled compressors. Water delivery must be verified to operating temperature. The fan air requirement is the
assure constant delivery of the volumes outlined in Table amount of air, which must flow through the compressor for
4-1 Water Flow Requirements on page 52. The figures proper ventilation. The heat rejection requirement is the
shown are for full-load operation utilizing an aftercooler. amount of heat that is radiated by the compressor. This
Cooler water will reduce water-flow requirements and heat must be removed to assure a normal operating
warmer water will increase water-flow requirements. temperature. With air-cooled compressors it is possible to
Water piping to and from the compressor unit must be a use this heat for space heating, providing additional
minimum of 1 inch diameter. Isolation valves with side pressure drop across the fan does not exceed 0.2 in H2O.
drains should be installed on both input and return lines. Consult a Sullair office for assistance in utilizing this heat.
Input water should have a 2 mm strainer installed in-line. If ductwork is added, the high static fan option is required.
A normally closed solenoid valve should be connected to DO NOT install a water-cooled or an air-cooled/after-
the water outlet of the compressor. The compressor cooled compressor where it will be exposed to
control circuit switches this circuit. Consult the Sullair temperatures less than 32˚F (0˚C). Consult factory for
Service Department for assistance in these setups. machine operation in ambient temperature less than 32˚F
Water quality is critical to proper cooling of the (0˚C).
compressor. Excessive build-up of lime, scale or other If machine is equipped with water regulating valve, use the
deposits can restrict the flow of water to the compressor. water regulating valve to adjust compressor temperature
These deposits act as a thermal insulator and reduce the to maintain a minimum of 180°F (82.2°C); 190°F (87.8°C)
efficiency of the water cooler. for 24KT.
The cleaning of piping and water coolers is the customer’s Temperature and pressure gauges should be installed in
responsibility. Inspect all piping for deposits and clean as the water piping for use in troubleshooting of the water
necessary. Refer to system. Water pressure should ideally be between 25 and
Water Quality Recommendations on page 53. 75 psig (1.7 and 5.2 bar) but must not be above 145 psi
TABLE 4-1 WATER FLOW REQUIREMENTS (10 bar).
Water Flow
Water Temp Gallons Per Minute /Liters Per Minute (l)
˚F/˚C
40HP/30kW 50HP/37kW 60HP/45kW
70/21 5.6 7.0 (26.5) 9.0 (31.6)
80/27 8.4 10.5 (35.7) 11.5 (41.6)
(I) Water pressure should be maintained between 25 and 75
psig (1.7 and 5.2 bar), but not to exceed 145 psig (10 bar)

® SULLAIR ®
INSTALLATION
TABLE 4-2 VENTILATION REQUIREMENTS

Cooling Type Air-Cooled with Aftercooler Water-Cooled
Motor HP/kW 40 / 30 50 / 37 60 / 45 40 / 30 50 / 37 60 / 45
Fan Air cfm/m3/hr 5,000 / 8,500 5,000 / 8,500 6,000 / 10,200 700 / 1,200 700 / 1,200 700 / 1,200
Ventilating Air/Heat

Rejection
BTU/Hour 114,500 142,000 171,100 10,600 13,300 15,800
KCal/Hour 28,800 35,700 46,216 2,670 3,350 4,000
Cooling Water/Heat

Rejection

BTU/Hour 114,500 142,000 171,100
KCal/Hour 28,800 35,700 43,040
Water System Venting surface of lakes. A higher pH value will also assist in the
formation of lime scale. In all cases calcium will form scale
Vent the system upon installation or after draining the when water that has dissolved calcium is heated. It then
system on start-up: forms lime-scale on surfaces such as the inside of pipes
1. Open the water valve(s) allowing water to flow to the and the tubing that comprises water coolers. Scale
system. formation on the inside of pipes and inside of heat
2. Open the vent cocks (located on top of the aftercooler exchangers acts as a thermal insulator. This causes
and the lubricant cooler) and allow all air to escape coolers to be less effective, and piping to have reduced
from the system. When water is observed at the vent water flow, making them less effective. Over time lime
cocks, close them. scale build-up can reduce water flow by 80% or greater.
This renders the cooling system ineffective and will
The system is now vented. damage the system. Scale can be controlled with water
treatment.
Draining The Water System
Corrosion
If the system needs to drained completely, follow the steps
outlined below: As contrasted to lime scale build-up, corrosion eventually
causes a reduction in the wall thickness of pipes. High
1. At the rear of the unit. Disconnect both the inlets and levels of dissolved oxygen and low pH levels assist in the
discharge water lines. creation of corrosive scale. A thin coating of lime scale is
2. Remove the drain plugs located at the bottom of the often beneficial in helping to prevent corrosion from
aftercooler and lubricant cooler. forming.
3. Allow the system to drain completely.
Biological And Organic Fouling (Slime)
Water Quality Recommendations The heightened temperatures of compressor cooling
operations help to reduce the likelihood that organic
Water quality considerations are crucial to the effective
fouling will become a major concern. In the event of an
operation of a water-cooled compressor and yet are the
infestation, commercial chemical shock treatments are
most often ignored. Premature failure of components can
available to control any outbreaks.
often be traced to a reduction in heat-transfer rate that has
resulted from a reduced flow rate due to scale build-up in To ensure maximum life expectancy and best
water-cooling lines or the coolers themselves. performance of the compressor cooling system, refer to
Scale Table 4-3 Water Tests on page 54.
Scale is formed from calcium carbonate, which
precipitates out of water. Calcium content tends to be
higher in water taken from wells than water taken from the
® SULLAIR ®
SECTION 4
TABLE 4-3 WATER TESTS

Substances Test Interval Acceptable Concentration
Corrosivity Hardness, pH, Total Dissolved Monthly - if stable for 3 to 4 months, analyze Langelier Index 0 to 1
Solids, Temperature at inlet, Alkalinity quarterly.
Iron Monthly < 2 ppm
Sulphate Monthly < 50 ppm
Chloride Monthly < 50 ppm
Nitrate Monthly < 2 ppm
Silica Monthly < 100 ppm
Desolated Oxygen Daily - if stable, analyze weekly 0 ppm (as low as possible)
Oil & Grease Monthly < 5 ppm
Ammonia Monthly < 1 ppm
Seawater-Cooled Units No oil cooler manufacturer can guarantee that its products
will have an indefinite life and for this reason, we suggest
NOTE that the cooling system be designed to minimize any
damage caused by oil cooler leaking. This can be
If seawater is to be used for cooling, achieved as follows:
optional copper-nickel coolers must 1. The oil pressure should be maintained at a pressure
be selected. higher than the seawater pressure. In the event of a
leak occurring, the oil will be prevented from becoming
Water cleanliness is critical for operation of the contaminated.
compressor. A strainer must be installed in the inlet piping 2. When the hydraulic system is not in use, the coolers
of the water system. It is also recommended that a should be isolated from incoming seawater under
solenoid valve (normally closed) be installed into the water pressure.
outlet side of the compressor system. Consult the Sullair 3. The seawater outlet pipe from the cooler should have
Service Department for assistance in setting up these an open run to waste piping.
recommended precautionary functions. In addition, be
aware that cleaning of coolers as a result of fouling is a Outdoor Installation (Sheltered)
customer responsibility.
Many times a compressor must be installed outside due
Isolation valves with side drains should be installed on to available space or other jobsite conditions. When this is
both the inlet and outlet lines. necessary, there are certain items that should be
incorporated into the system to help ensure trouble-free
The recommended flow rate cannot be exceeded. An operation. The unit must be purchased with a TEFC motor.
orifice plate must be installed in the pipe-work at least The standard machine has NEMA4 rated controls, which
3.3 ft (1 m) before the cooler. The orifice size must be are watertight.
calculated to ensure that the maximum seawater flow rate
cannot be exceeded. Without these precautions, the
seawater flow rate through the cooler may be several times NOTE
the recommended maximum, which will lead to rapid
Variable speed drive compressors are
system failure.
NEMA 12 rated and must not be
Orifice diameter in inch installed outside or exposed to the
Seawater pressure (mm) to give a maximum elements.
psi (Bar) seawater flow or 40 US gal/
min (152 l/min ) The compressor should be on a concrete pad, which is
25 (1.7) 0.675 (17) designed to drain water away from it. If the concrete pad
is sloped, then the compressor must be mounted so that
35 (2.4) 0.62 (16) it is level. The base or skid must be fully supported where
45 (3.1) 0.58 (15) it contacts the concrete pad.
55 (3.8) 0.55 (14) A weatherhood option should be selected to prevent direct
65 (4.5) 0.53 (13.5) rain and snow from falling on the unit. If local weather
conditions can be extreme such that direct rain or snow
75 (5.2) 0.51 (13) may fall on the unit, it should be in a fully enclosed room
or building.

® SULLAIR ®
INSTALLATION
If installed under a shelter, air-cooled machines must be A built-in aftercooler reduces the discharge air
positioned in a way that prevents air recirculation (i.e., hot temperature below the dew point. For most ambient
exhaust being allowed back to the system air inlet). conditions, considerable water vapor is condensed. To
remove the condensation, each compressor with built-in
In installations that include more than one compressor, hot aftercooler is supplied with a combination condensate
air exhaust should not be directed toward the fresh air separator/trap. A drain line should be installed on the
intake of the second unit or an air dryer. condensate drain.
A standard machine installed outside must not be started
or run if the ambient temperature in and around the NOTE
compressor drops or may drop below 35˚F (1.7˚C).
For low-volume systems that do not
For installation in a below freezing climate, a low ambient require an auxiliary receiver,
option with heat tracing and a receiver tank heater must compressor response time may need
be installed.
to be adjusted. Consult the Sullair
Service Department for assistance.
4.3 SERVICE AIR PIPING
Review carefully the total air system before installing a new Fluid Containment
compressor. Items to consider for the total air system
include liquid carryover, pipe sizing, and the use of an Compressors are equipped with a fluid containment pan
auxiliary receiver. The installation of a drip leg or multiple to catch any fluid in the event of a leak or spill. The drain
drip legs, installation of a line filter(s) and the installation for the pan is located on the air intake end of the machine.
of isolation valve or valves. These considerations are For indoor installations, the drain should be plugged to
important to ensure a safe and effective system. contain fluids. For outdoor applications, the drain must be
connected to a separate, customer supplied system to
allow rainwater or any accumulated compressor fluid to
NOTE drain out.
Discharged air contains a very small
amount of compressor lubricating oil, CAUTION
and care should be taken to ensure
The use of plastic bowls on line filters
that this oil would not interfere with
and other plastic airline components
downstream equipment. Downstream
without metal guards can be
filters and an air dryer can remove any
hazardous. Synthetic coolants or the
carryover.
additives used in mineral oils can alter
their structural integrity and create
Pipe Sizing hazardous conditions. Metal bowls
Pipe should be sized at least as large as the discharge should be used on any pressurized
connection of the compressor. Piping and fittings should system for safety concerns.
all be suitably rated for the discharge pressure. "The Plastic Pipe Institute
recommends against the use of
Use of Auxiliary Receiver Tank
thermoplastic pipe to transport
An auxiliary receiver tank should be used in cases where compressed air or other compressed
large demand swings are expected. gases in exposed above ground
locations, e.g. in exposed plant
Isolation Valve(s) piping." (I)
If isolation of the compressor from the service lines is Sullube should not be used with PVC
required, isolation valves should be installed close to the
piping systems. It may affect the bond
discharge of the compressor. They should be installed
with drip legs that drain sloping downward from the base at cemented joints. Certain other
in order to drain properly. Install a vent to the piping plastic materials may also be affected.
downstream of the compressor outlet connection. (I) Plastic Pipe Institute,
Recommendation B, Adopted
When two compressors are operated in parallel, provide January 19, 1972.
an isolation valve and a drain trap for each compressor
before the common receiver.
® SULLAIR ®
SECTION 4
4.4 COUPLING ALIGNMENT CHECK DANGER

No coupling alignment is required. Lethal shock hazard inside.
Disconnect all power at source before
4.5 FLUID LEVEL CHECK opening or servicing.
The air compressor is shipped with the proper amount of
fluid installed. However, it is necessary to check the fluid 1. Check incoming voltage. Be sure that the incoming
level at the time of installation and during continued voltage is the same voltage that the compressor was
operation of the compressor. The fluid level is to be wired for.
checked when the compressor is in the SHUT DOWN 2. Check motor starter and overload heater sizes.
MODE (fluid level may not be visible when operating), and
by looking at the sight glass on the receiver tank. To be 3. Check all electrical connections for tightness.
able to see the fluid level it may be necessary to start the 4. "DRY RUN" the electrical controls by disconnecting
machine and build the receiver tank pressure up to 10/20 the three (3) motor leads from the starter. Energize the
psi and then shut down. If no fluid level is seen in the sight control circuits by pushing the " " (START) pad and
glass add fluid to the center of the glass. Do not overfill in check all protective devices to be sure that they will
any case. When a complete fluid change is performed, fill de-energize the starter coil when tripped.
the receiver tank to the maximum allowable fluid level, 5. Reconnect the three (3) motor leads and jog the motor
which is center of the sight glass. for a direction of rotation check, as explained in Motor
Rotation Direction Check on page 56.
4.6 ELECTRICAL PREPARATION
Interior electrical wiring is performed at the factory. 4.7 MOTOR ROTATION DIRECTION
Required customer wiring should be done by a qualified CHECK
electrician in compliance with OSHA, National Electric
Code and/or any applicable local electrical code Motor rotation check must be made at compressor start-
concerning isolation switches, fused disconnects, etc. up. The compressor can be damaged if it runs in the wrong
Sullair provides a wiring diagram for use by the installer. direction for more than a few seconds. Motor rotation can
An electrical check should be made to help assure that the be viewed through the opening in the drive adapter
first start-up will be trouble-free. The compressor and drive housing. After the electrical wiring has been done, it is
should be properly grounded/earthed in accordance with necessary to check the direction of the motor rotation. Pull
Local and National Code requirements. out the EMERGENCY STOP button and press once,
quickly and in succession, the " " (START) and
Installation of this compressor must be in accordance with " " (STOP) pads. This action will bump start the motor
recognized electrical codes and any local Health and for a very short time. When looking at the motor from the
Safety Codes. end opposite the compressor unit, the shaft should be
Feeder cables should be sized by the customer/electrical turning clockwise. If the reversed rotation is noted,
contractor to ensure that the circuit is balanced and not disconnect the power to the starter and exchange any two
overloaded by other electrical equipment. The length of of the three power input leads, then re-check rotation. A
wiring from a suitable electrical feed point is critical as "Direction of Rotation" decal is located on the motor drive
voltage drops may impair the performance of the housing to show proper motor/compressor rotation. An
compressor. Cable sizes may vary considerably so the alternative to this procedure is to set the WS Controller to
mains terminals will accept up to 50 mm2 (1 awg) (37/4 Sk display P1 receiver tank pressure. Pull out the
& 50/60 H) and up to 90 mm2 (3/0 awg) (55/75 k & 75/100 EMERGENCY STOP button and press once, quickly and
H) cable. in succession, the " " (START) and " " (STOP) pads.
This action will bump start the motor for a very short time.
Feeder cable connections to incoming terminals L1‐L2‐L3 If motor rotation is correct there will be immediate pressure
should be tight and clean. shown. If no pressure is present, reverse rotation is
occurring. Disconnect the power to the starter and
The applied voltage must be compatible with the motor exchange any two of the three power input leads. Recheck
and compressor data plate ratings. rotation as outlined above.
A starter hole is provided for incoming power connection. Fan motor rotation should also be checked. It should rotate
If it is necessary to make a hole in the control box in a counter-clockwise when viewing the fan motor from the
different location, care should be taken to not allow metal backside of the motor.
shavings to enter the starter and other electrical
components within the box. If another hole is used, the
original hole must be blocked off:

® SULLAIR ®
® SULLAIR ®
Section 5
WS CONTROLLER
5.1 CONTROLLER LAYOUT
3
2
10
7 9
6 4
SU_0000021
1. ON 6. Maintenance Indicator
2. OFF 7. Fault Indicator
3. LCD Display 8. Up Key
4. Power Indicator 9. Down Key
5. Run Mode Indicator 10. Enter Key
Figure 5-1: WS Controller
5.2 CONTROLLER KEYPAD • To stop compressor operation, press the red Stop pad
" ".
The WS Controller keypad has two main pads for • The Run mode indicator " " lights up whenever the
compressor control. control is in an operating mode.
• To start the compressor operation, press the green
Start pad " ".
® SULLAIR ®
SECTION 5
5.3 LCD DISPLAY Refer to Figure 5-6. Press the Down arrow " " to display
additional information about the compressor. The upper
The display's normal view shows the compressor line will indicate "Compressor Status" and the name of the
package's discharge pressure, internal temperature, and temperature, pressure, or other measurement. The lower
the operating mode. The modes are MANUAL, OFF, line indicates the present reading.
AUTOMATIC, or FAULTED.
SA_0000003R01
SA_0000005R01
Figure 5-6:
Figure 5-2:
Refer to Figure 5-7. When you continue beyond the status
Refer to Figure 5-2 and Figure 5-3. The lower line is information, the display will show a list of control settings.
occasionally interrupted to describe the compressor The upper line will indicate "Show Setting" and the name
package's operating state. of the setting. The lower line shows the present value.
SA_0000004R01 SA_0000006R01
Figure 5-3: Figure 5-7:

Refer to Figure 5-4. If a machine fault occurs, the red fault Refer to Figure 5-8. To change the setting, press the Enter
" " indicator will light up, and the display will indicate that pad " ". The display indicates that you are in a change
a fault has occurred. mode with reverse characters. Use the Up " " or Down
" " arrow keys to change the setting, and press Enter
again to save the new setting.
SA_0000001R01
Figure 5-4: SA_0000007R01
Refer to Figure 5-5. The lower line periodically will display Figure 5-8:
the cause of the fault. Refer to service instructions to
correct the cause. Press the Stop pad " " to reset the Refer to Figure 5-8. If there is no keypad activity, the
controller. display will return to normal view in about one minute. If
the Start or Stop buttons are pressed, the display also
returns to normal view. If either of these occur, the setting
will not be altered.
If there are any warnings or recommended service
instructions, these will be periodically displayed on the
normal view.
The list of displays may be navigated from either direction
SA_0000002R01
Figure 5-5: by using the Up " " or Down " " arrow keys. For
example, to change language from normal view, press the
Up arrow pad once, press the Enter key " ", select your
language, and press Enter again. The number of displays
varies with compressor model, but will follow this pattern.

® SULLAIR ®
WS CONTROLLER
The large Emergency Stop button located near the

controller overrides all electronic functions to turn off the
control devices. The controller senses this, and will display
E-stop. To reset, twist and pull out the Emergency Stop
button, then press the Stop pad to reset the WS Controller.
5.4 LED LIGHTS

The four LED lights indicate the general condition of the
machine.
The green Power indicator " " simply indicates that

power is applied to the controller. It will blink very slowly if
the WS Controller is set up to automatically restart after
power failure.
The green Run mode indicator " " indicates compressor
operation is enabled. It lights steadily if the motor is
running. If the motor stops while in Automatic mode, this
LED will blink to indicate that the motor may restart.
The yellow Maintenance indicator " " comes on

whenever there is recommended maintenance or a
warning. The text display will periodically indicate the
recommended actions or the cause of the warning.
The red Fault indicator " " indicates that a compressor

fault has occurred and needs to be repaired before further
operation. The text display will indicate the cause of the
fault.
The PC support program for the WS controller provides
additional information about compressor operation and
advanced setup adjustments to optimize operation.
Software part numbers are shown in the display following
a power interruption or other interruption of
communication with the controller. The P/N remains on the
display until satisfactory communications are established
with the Input/Output module.
® SULLAIR ®
SECTION 5

® SULLAIR ®
® SULLAIR ®
Section 6
MAINTENANCE
6.1 GENERAL After a routine start has been made, observe the controller
display and be sure it monitors the correct readings for
As you proceed in reading this section, it will be easy to their particular phase of operation. After the compressor
see that the Maintenance Program for the air compressor has warmed up, it is recommended that a general check
is quite simple. The use of the service indicators provided on the overall compressor be made to assure that the
for the fluid filter, air filter and fluid separator will alert you compressor is running properly.
when service maintenance is required. When the WS
Controller display indicates service, maintenance for that 6.3 MAINTENANCE AFTER INITIAL
specific item is required. See instructions for each item in
Filter Maintenance, on page 62. 50 HOURS OF OPERATION
After the initial 50 hours of operation, a few maintenance
6.2 DAILY OPERATION requirements are needed to clean the system of any
foreign materials. Perform the following maintenance
Prior to starting the compressor, it is necessary to check operations to prevent unnecessary problems:
the fluid level in the receiver tank . Should the level be low,
simply add the necessary amount. If the addition of fluid 1. Clean the return line strainer. Refer to Maintenance
becomes too frequent, a simple problem has developed Every 2000 Hours on page 62 for location.
which is causing this excessive loss. See the 2. Clean the return line orifice.
Troubleshooting Guide Section under EXCESSIVE
COMPRESSOR FLUID CONSUMPTION for a probable
cause and remedy.
WARNING
HIGH-PRESSURE HAZARD!
• DO NOT remove caps, plugs, and/or
other components when
compressor is running or
pressurized. Stop compressor and
relieve all internal pressure before
doing so.
• Failure to comply could result in
death or serious injury.
® SULLAIR ®
SECTION 6
6.4 MAINTENANCE EVERY 2000 1. Using a wrench, remove the filter canister.
2. Remove and dispose of filter element. Observe all
HOURS laws and regulations for filter disposal.
After 2000 hours of operation, it will be necessary to 3. Clean gasket seating surface.
perform the following:
4. Apply a light film of fluid to the element seal.
1. Clean the return line strainer. Refer to Discharge,
5. Install the element into the filter canister.
Receiver and Piping System, 3000P, 3700 and 4500
on page 96. 6. Screw the canister to the filter head. Tighten to 10 to
12 ft•lb (13.5 to 16.0 N·m).
2. Replace the fluid filter element.
7. Restart compressor and check for leaks.
6.7 AIR FILTER MAINTENANCE
3
2
2
1
SA_0000018
3 1. Housing
2. Element*
3. Cover
SA_0000017
Air Filter Assembly: P/N 02250127-683
1. Filter Head * Replacement Air P/N 02250127-684
2. Element* Filter Element Kit:
3. Body
Figure 6-2: Air Filter Assembly
Fluid Filter Assembly: P/N 02250155-708
Refer to Figure 6-2. Air filter maintenance should be
*Fluid Filter P/N 02250155-709
performed when the maintenance gauge shows red with
Replacement Kit:
the compressor running full load, or once a year,
Figure 6-1: Fluid Filter Assembly whichever comes first. If the filter needs to be replaced,
order a replacement element. Below you will find
procedures on how to replace the air filter element.
6.5 FLUID MAINTENANCE
Drain the receiver tank and change the compressor fluid
using instructions shown in
Lubrication Guide on page 20.
6.6 FILTER MAINTENANCE

Refer to Figure 6-1. Replace your fluid filter element under
any of the following conditions, whichever occurs first:
1. As indicated by the WS Controller.
2. Every fluid change.
Fluid Filter Element Replacement

Refer to Figure 6-1.

® SULLAIR ®
MAINTENANCE
Air Filter Element Replacement 6.8 SEPARATOR MAINTENANCE

1. Clean exterior of air filter housing. Replace the separator element when indicated by the WS
2. Rotate end cover counterclockwise and remove Controller or after one (1) year, whichever comes first. The
3. Remove air filter element by pulling it out of the separator element must be replaced. DO NOT attempt to
housing. clean the separator element.
4. Clean interior of housing using a damp cloth. DO Separator Element Replacement
NOT blow dirt out with compressed air.
Refer to Figure 6-3. The separator element must be
5. At this time replace the element. changed when indicated by the WS Controller, or once a
6. Reassemble in the reverse order of the disassembly. year, whichever occurs first. Follow the procedure
explained below for separator element replacement:
NOTE
Relieve all pressure from the receiver
tank and all compressor lines.
1. Loosen and remove the eight (8) hex head capscrews

(M12 x 40mm) from the cover plate.
2. Lift the cover plate from the receiver tank.
3. Remove the separator element.
4. Inspect the receiver tank for rust, dirt, etc.
5. Reinsert the separator element into the receiver tank
taking care not to dent the element against the tank
opening.
6. Install a new lubricated O-ring in the O-ring groove on
the underside of the receiver tank cover.
7. Replace the cover plate, washers and capscrews.
Torque to 89 ft·lbs. (121 N·m).
8. Clean the return line strainer before restarting the
compressor.
® SULLAIR ®
SECTION 6
Oil Return/Sight Glass Maintenance

1
Refer to Figure 6-4. The oil return/sight glass subassembly
2 is attached to the side of the separator tank. Oil return/sight
3 glass maintenance should be performed on a routine basis
4 parallel to that of the fluid filter, or as indicated in the
troubleshooting section of this manual. The maintenance
on an oil return/sight glass is mainly concerned with the
condition of the filter assembly. Order filter assembly No.
02250117-782, and use the following instructions as a
guide:
5
2
3
4
6
5
SA_0000019
6
1. Cover
2. Ground Spring*
3. Spring Fastener* 7
4. Cover Gasket*
5. Element*
6. Receiver Tank
Separator Element: P/N 02250160-774 8
*Separator Element P/N 02250160-776
Replacement Kit: SU_0000032
Figure 6-3: Separator Element Assembly 1. To Receiver Tank

2. Male Tube Connector
3. 90˚ Pipe Elbow
4. Filter Assembly*
5. Sight Glass/Orifice Block
6. Brass Plug Orifice
7. Female Tube Connector
8. To Unit
* Oil Return Filter P/N 02250117-782
Replacment Kit:
Figure 6-4: Oil Return/Sight Glass
1. Disconnect the tube at bottom of sight glass.
2. Unscrew the sight glass assembly where the elbow
fitting joins the strainer/filter.
3. Remove used filter assembly, and replace with new
assembly.

® SULLAIR ®
MAINTENANCE
4. Inspect and clean the orifice inside the sight glass from the strainer and remove the strainer screen. Clean
blocks. The orifice must be removed with an allen the screen and reinstall. If the screen is damaged, the
wrench. strainer assembly must be replaced (P/N 241772).
5. Coat/lubricate the O-rings with silicone grease.
Shaft Coupling Maintenance
6. Reattach the connectors to the sight glass/orifice
blocks. The compressor unit and motor are rigidly connected via
a mounting adapter housing. This arrangement makes
Pressure Regulator Adjustment coupling alignment unnecessary. The coupling is a jaw
type in shear. If the elastomeric element requires
Refer to Figure 6-5. Start the compressor and adjust the replacement due to wear or breakage, order replacement
service valve to maintain service air pressure element no. 02250152-670, and follow the following steps:
approximately at 1 psi over rated pressure. Turn the inlet
valve regulator adjusting screw until air just begins to 1. Remove the protective grill from the adapter housing.
escape from the control air orifice, located at the bottom 2. Loosen the retaining screw located on the outer
of the regulator. Lock the adjusting screw in place with the sleeve. Slide the sleeve to one side, exposing the
locknut. The regulator is now properly set. coupling element.
3. Unwrap the coupling element from the coupling jaws.
4. Install the new element by wrapping it around the jaws,
engaging the cogs on the element into the jaws.
5. Reinstall the outer sleeve and the protective grill.
Secure the outer sleeve by tightening the two screws
to 45 in·lbs (5 N·m).
6.9 TROUBLESHOOTING -
INTRODUCTION
The information contained in the Troubleshooting Guide
has been compiled from field report data and factory
experience. It contains symptoms and usual causes for the
described problems. However, DO NOT assume that
these are the only problems that may occur. All available
2 data concerning a problem should be systematically
1 analyzed before undertaking any repairs or component
replacement procedures.
SU_0000033 A detailed visual inspection is worth performing for almost

all problems and may avoid unnecessary additional
damage to the compressor. Always remember to:
1. Locking Nut
2. Adjustment Screw 1. Check for loose wiring.
Figure 6-5: Regulator Adjustment 2. Check for damaged piping.
3. Check for parts damaged by heat or an electrical short
Water Condensate Drain Maintenance circuit, usually apparent by discoloration or a burnt
odor.
If your compressor is fitted with the standard solenoid
condensate drain valve, it is necessary to periodically Should your problem persist after making the
clean the strainer. Remove the hex cap from the strainer recommended check, consult your nearest Sullair
and remove the strainer screen. Clean the screen and representative.
reinstall. If the screen is damaged, the strainer assembly
must be replaced (P/N 241772).
Control Line Strainer

The regulator and solenoid valve(s), which control the
compressor, are protected by a strainer. Every 12 months
it is necessary to clean the strainer. Remove the hex cap
® SULLAIR ®
SECTION 6
6.10 TROUBLESHOOTING GUIDE

SYMPTOM PROBABLE CAUSE REMEDY
Compressor Will Not Start Main Disconnect Switch Open Close switch.
Line Fuse Blown Replace fuse.
Motor Starter Overload Tripped Reset. Should trouble persist, check
whether motor starter contacts are
functioning properly.
Low Incoming Line Voltage Check voltage. Should voltage check low,
consult power company.
Compressor Shuts Down With Air Demand Loss of Control Voltage Check power supply for 24V DC output.
Present Replace power supply if necessary.
Low Incoming Voltage Consult power company.
Excessive Operating Pressure Reset. If trouble persists, check that line
pressure does not exceed maximum
operating pressure of the compressor
(specified on nameplate).
Separator Requires Maintenance Indicated Replace separator.
by WS Controller
Machine Programmed for Wrong Pressure Reprogram with WSPC equipped laptop.
Setting
Defective Regulator Valve Regulator valve should cause inlet valve to
close when the pressure switch contacts
open. Repair if defective.
Defective Blowdown Valve Blowdown valve should exhaust receiver
tank pressure to 18 psig (1.2 bar) when
maximum operating pressure is reached.
Repair if defective.
Cooling Water Temperature Too High Reduce water temperature to 85°F
(29.4°C) or less. Water-cooled only.
Cooling Water Flow Insufficient Check water lines and valves
(water-cooled only).
Cooler Plugged Clean tubes. If plugging persists, install
water conditioner (water-cooled only).
Cooling Air Flow Restricted Clean cooler and check for proper
ventilation.
Ambient Temperature Is Too High Provide sufficient ventilation.
Low Fluid Level Add fluid.
Clogged Filter Change the fluid filter element.
Thermal Valve Not Functioning Properly Replace element.
Water Flow Regulating Valve Not Change (water-cooled only).
Functioning Properly

® SULLAIR ®
MAINTENANCE
6.10 TROUBLESHOOTING GUIDE (CONTINUED)

Compressor Will Not Build Full Discharge Air Demand is Too Great Check service lines for leaks or open valves.
Pressure
Dirty Air Filter Check the filter indicator and inspect and/or
change element if required.
Inlet Valve Bleed Orifice Plugged Ensure control line bleed orifice located
inside inlet valve is not plugged.
Pressure Regulator Out of Adjustment Adjust regulator according to control
adjustment instructions in the Maintenance
section.
Defective Pressure Regulator Replace regulator.
Defective Unload Solenoid Valve Check that the valve closes when
energized. Replace the coil or the complete
valve if defective.
Line Pressure Rises Above Unload Leak in Control System Causing Loss of Check for leaks.
Pressure Set-Point Pressure Signals
Inlet Valve Stuck Open Remove the intake hose and check for inlet
valve operation.
Defective Unload Solenoid Valve Check that the valve is open when de-
energized. Replace if necessary.
Plugged Control Line Strainer Clean strainer (screen and O-ring
replacement kit available).
Defective Blowdown Valve Check that receiver tank pressure is
exhausted to the atmosphere when the
solenoid valve opens. Repair or replace if
necessary (kit available).
Excessive Compressor Fluid Consumption Clogged Return Line or Orifice Clean strainer (screen and O-ring
replacement kit available).
Clean orifice.
Separator Element Damaged or Not Change separator.
Functioning Properly
Leak in the Lubrication System Check all pipes, connections and
components.
Excess Fluid Foaming Drain and change.
Fluid Level Too High Drain and change. Check that the
compressor temperature has not dropped
below 170°F (76.7°C).
Pressure Relief Valve Opens Repeatedly Defective Pressure Relief Valve Replace.
Plugged Separator Check separator differential.
® SULLAIR ®
SECTION 6
6.10 TROUBLESHOOTING GUIDE (CONTINUED)

Liquid Water In Compressed Air Lines Plugged Strainer in Moisture Drain Line Clean and service strainer located in the line
off the bottom of the water separator.
Water Vapor Condensation from Cooling Remove the water vapor from compressed
and Compression Occurs Naturally air prior to distribution through the air
system. Check operation of aftercooler and
moisture separator. Install a compressed air
dryer sized for the flow and dryness level
required. (Note: Filters may also be required
to remove particulates, liquid oil aerosols or
for oil vapor removal. Change cartridges as
recommended by the filter manufacturer).
Check all drain traps routinely to insure their
proper operation. Maintain them regularly.
Defective Drain Solenoid Valve Ensure valve opens and closes as signaled
by the WS Controller.
Inadequate Drain Timer Settings Check WS Controller control drain interval
and drain time, and adjust accordingly. High
humidity conditions require longer drain
times or more frequent openings.

® SULLAIR ®
® SULLAIR ®
Section 7
VSD CONTROL
OPERATION
7.1 DESCRIPTION OF COMPONENTS Full Load Mode- 50 to 100
The variable speed drive unit is located in the machine
PSIG (3.4 to 6.9 Bar)
electrical enclosure. The heat sink for the drive extends When the compressed air pressure rises over 50 psig
through the back of the enclosure, and is cooled by airflow (3.4 bar) the minimum pressure valve opens allowing
through the compressor enclosure. compressed air to flow into the service line. From this point
on the line pressure is continually monitored by the WS
7.2 CONTROL SYSTEM, Controller, which controls the variable speed drive. The
pressure regulator and solenoid valve remain closed with
FUNCTIONAL DESCRIPTION the inlet valve fully open running at 100 psig (6.9 bar) or
below.
Refer to Figure 2-5. The purpose of the compressor control
system is to regulate the amount of the air being Variable Speed Drive Part Load Control
compressed to match the amount of compressed air being
used. The Capacity Control System consist of variable If less than rated capacity of compressed air is being used,
speed drive, solenoid valve, regulating valve, and the inlet the service line pressure will rise above 100 psig
valve. The functional description of the control system is (6.9 bar). Consequently, the Variable Speed Drive will
described below in six distinct phases of operation. The begin to decelerate the motor, thereby reducing the output
following description text applies to 3000V, 3000PV, capacity to match demand. The drive will continuously
3700V and 4500V series variable speed drive adjust the motor speed (accelerate or decelerate) to
compressors with WS Controller. Depending on the maintain a line pressure of 100 psig (6.9 bar). In this mode
model, the compressor can be operated at a setpoint the VSD will operate within the appropriate frequency
pressure from 60 to 175 psig (4.1 to 12.1 bar). Refer to the range determined by the WS Controller.
nameplate for operating pressure range. The WS
Controller will automatically set the frequency range based Modulating Mode- 100 to 106
on the selected pressure. For explanatory purposes, this PSIG (7.3 to 6.9 Bar)
description will apply to a compressor with an operating
pressure of 100 psig (6.9 bar), and load delta setting of 6 During low demand periods and with the Variable Speed
psi (0.4 bar). The load delta has a default setting of 10 psi Drive at minimum speed, the line pressure can continue to
(0.7 bar), but is recommended to set at 6 psi (0.4 bar) for rise. When the line pressure reaches 101-102 psig
most efficient operation. A compressor with any other (approximately 7 bar), the regulator valve (Figure 7-7)
pressure range would operate in the same manner except gradually opens, directing air pressure to the inlet control
stated pressures. valve piston. This action causes the inlet valve to partially
close, thereby reducing the air entering the compressor
Start Mode- 0 to 50 PSIG (0 to 3.5 Bar) until it matches the amount of air being used. The control
system functions continually in this manner between the
When the WS Controller " " (START) button is limits of > 101 psig (7.0 bar) to 106 psig (7.3 bar), in
depressed, the VSD ramps the motor to full speed and the response to varying flow demand. The pressure regulator
receiver tank pressure will quickly rise from 0 to 50 psig has an orifice which vents a small amount of air to the
( 0-3.4 bar). During this period, both the regulator and atmosphere when the pressure regulator controls the inlet
solenoid valves are closed, the inlet valve is fully open and valve. The orifice also bleeds any accumulated moisture
the air-end delivers full capacity to the receiver tank. The from the control line. When the discharge pressure rises
rising compressor air pressure is isolated from the service above 106 psig (7.3 bar), or alternatively set unload
line in this phase by the minimum pressure valve set at pressure the compressor unloads.
approximately 50 psig (3.4 bar).
® SULLAIR ®
SECTION 7
NOTE
With a Sullair compressor, there is no
maintenance or inspection of the
internal parts of the compressor unit
permitted in accordance with the
terms of the warranty.
Unload Mode- In Excess of 106

PSIG (7.3 Bar)
When a relatively small amount or no air is being used, the
service line pressure continues to rise. When it exceeds
106 psig (7.3 bar), or alternatively set unload pressure, the
WS control system de-energizes the solenoid valve
allowing receiver tank air pressure to be supplied directly
to close the inlet valve. Simultaneously, the solenoid valve
sends a pneumatic signal to the blow down valve. The
blowdown valve opens to the atmosphere, reducing the
receiver tank pressure. The check valve in the air service
line prevents line pressure from returning to the receiver
tank . The compressor will shut down after the unload time
setting expires if programmed (the default setting is zero
[0] seconds for an immediate shutdown upon unload).
When the line pressure drops to the low setting pressure
of 100 psig (6.9 bar) The WS Controller starts the motor
and energizes the solenoid valve which closes the blow
down valve. The re-energized solenoid valve prevents line
pressure from reaching the inlet control valve, thereby
allowing it to fully open, and the compressor again delivers
compressed air to the system.

® SULLAIR ®
® SULLAIR ®
Section 8
PARTS LISTS
8.1 PROCEDURE FOR ORDERING PARTS
When ordering parts always indicate the Serial Number of the compressor. This can be obtained from the Bill of Lading
for the compressor or from the Serial Number Plate located on the compressor. Refer to Figure 8-1.
SU_0000446
Figure 8-1: Serial Plate, Serial Number Location
® SULLAIR ®
SECTION 8
Parts should be ordered from the nearest Sullair Representative or the Representative from whom the compressor was
purchased. If for any reason parts cannot be obtained in this manner, contact the factory directly at the addresses, phone
and fax numbers listed below.

® SULLAIR ®
PARTS LISTS
8.2 RECOMMENDED SPARE PARTS LIST

ELEMENTS
1 element, compressor fluid filter 02250155-708 02250155-709 1
2 element, heavy duty air filter (3000P, 3700, 4500) 02250127-683 02250127-684 1
3 element, heavy duty air filter (3000) 02250125-369 02250125-372 1
4 element, replacement for separator 02250160-774 02250160-776 1
KITS
5 kit, repair for minimum pressure / check valve 02250097-598 02250110-727 1
6 kit, cap for minimum pressure check valve 02250097-598 02250046-396 1
7 kit, O-ring for minimum pressure check valve 02250097-598 02250048-363 1
8 kit, piston for minimum pressure check valve 02250097-598 02250051-337 1
9 kit, repair for thermal valve (Sullube) 02250092-081 02250144–327 1
10 kit, repair for thermal valve (24KT or 175 psig) 02250148-796 02250148–827 1
11 kit, repair for pressure regulator 250017-280 250019-453 1
12 kit, repair for blowdown valve 02250100-042 02250100-042 1
13 kit, repair for control solenoid valve 02250155-714 02250157-500 1
14 kit, coil replacement for control solenoid valve coil 02250155-714 02250157-502 1
15 kit, repair for condensate drain solenoid valve coil 02250155-715 02250157-501 1
16 kit, coil replacement for condensate drain solenoid valve coil 02250157-502 1
02250155-715
17 kit, repair inlet valve (integrated with compressor unit) 02250155-971 1
18 kit, rebuild inlet valve 02250155-970 1
19 kit, repair for v-type strainer 241771 241772 1
20 kit, repair for shaft seal (12 series) 02250050-363 1
21 kit, repair for shaft seal (10 series) 02250155-594 1
22 kit, tool for shaft seal installation (12 series) 602542-001 1
23 kit, repair for shaft seal installation (10 series) 001932–005 1
24 filter, scavenge line 02250117-782 02250117-782 2
25 kit, seal replacement for separator trap 02250144-635 02250144-735 1
LUBRICATION
26 fluid, SRF 1/4000 (5 gal/19 liter) 250019-662 (I)
27 lubricant, Sullube (Std.) (5 gal/19 liter) 250022-669 (I)
28 lubricant, 24 KT (5 gal/19 liter) 02250051-153 (I)
29 lubricant, Food Grade (5 gal/19 liter) 250029-008 (I)

(I) For proper amount of fluid fill, please consult Lubrication Guide in Section 3, Specifications.
CAUTION
warranties.
® SULLAIR ®
SECTION 8
8.3 COMPRESSOR, FRAME AND DRIVE, 3000P AND 3700 MODELS
02250152_458r01

® SULLAIR ®
PARTS LISTS
8.3 COMPRESSOR, FRAME AND DRIVE, 3000P AND 3700 MODELS

(CONTINUED)
1 frame, 37kw 02250151-176 1
2 isolator, vibration air end 50hp 02250151-500 2
3 adapter, compr/motor 50hp ma 02250151-630 1
4 grille, coupling guard 50hp 02250152-346 2
5 hub, coupling 1.75 bore falk 20r 02250152-624 1
hub, coupling 1.50 bore (3000) 02250152-662
7 element, cplg falk 20r 02250152-670 1
8 cover, cplg element falk 20r 02250152-678 1
9 isolator, vibration motor 37kw 02250155-285 2
10 plate, motor seal 3000/3700/4500 02250156-393 2
11 nut, hex metric m12 x 1.75 825912-175 2
12 capscrew, hex 8.8 m12 x 40mm 828012-040 8
14 capscrew, hex gr5 5/8-11 x 1 3/4 829110-175 4
15 washer, spr lock reg pltd 5/8 837810-156 4
16 washer, spr lock-metric pltd m12 838812-250 8
17 washer, iso 7093-8-140hv 865708-240 8
18 elbow, pipe 90 deg plt 1/2" 866215-020 1
19 nipple, pipe-xs plt 1/2 x cl 866408-000 1
20 screw, hex serr washer m8 x 25 882608-025 8
21 washer, nord-lock pl m12 sp 883212-254 4
22 compressor – (I) (II) 1
23 motor – (I) 1

A1 From Air Inlet Filter
A2 Oil Return From Sightglass on Receiver Tank
A3 To Receiver Tank
A4 From Blowdown Valve
A5 Main Oil Connection

(I) This part may vary per machine design. Consult factory with machine serial number to determine the proper part number.
(II) Sullair offers an exchange program whereby a remanufactured compressor unit can be obtained from Sullair distributors
or the factory at a lower cost than it would cost for the owner to repair the unit. For information regarding the unit exchange
program, contact your nearest Sullair representative or the Sullair Corporation. The shaft seal is not considered part of the
compressor unit in regard to the two year warranty, but the normal Sullair parts warranty does apply. For shaft seal repairs,
order repair kit no. 02250050-363, and installation kit no. 602542-001.
® SULLAIR ®
SECTION 8
8.4 COMPRESSOR, FRAME AND DRIVE, 3000 MODEL WITH 10 SERIES UNIT
A1
A4
A5 A3
A2
02250160-068R01

® SULLAIR ®
PARTS LISTS
8.4 COMPRESSOR, FRAME AND DRIVE, 3000 MODEL WITH 10 SERIES UNIT
(CONTINUED)
1 frame, 37kw 02250151-176 1
2 spacer,air end shaft height 60hp 02250151-499 2
5 element,cplg falk 20r 02250152-670 1
6 cover,cplg element falk 20r 02250152-678 1
8 plate, motor seal 3000/3700/4500 02250156-393 2
9 adapter, compressor 3700x w/10series 02250160-067 1
10 plate, motor/compr adapt cover 03 225980 1
11 adapter, motor compr 10/40 - 231977 1
12 adapter, sae 5 dxx10 gi ma - 250009-542 1
13 nut,hex pltd 3/8-16 825206-337 8
14 nut,hex metric m12 x 1.75 825912-175 2
15 capscrew,hex 8.8 m12 x 30mm 828012-030 2
18 capscrew,hex gr5 3/8-16 x 1 1/4 829106-125 7
19 capscrew,hex gr5 3/8-16 x 1 3/4 829106-175 8
20 capscrew,hex gr5 5/8-11 x 1 1/2 829110-150 4
24 nipple,pipe-xs plt 1/2 x cl 866408-000 1
27 motor 40hp – (I) 1

A3 To Receiver Tank

program, contact your nearest Sullair representative or the Sullair Corporation.
The shaft seal is not considered part of the compressor unit in regard to the two year warranty, but the normal Sullair parts
warranty does apply. For shaft seal repairs, order repair kit no. 02250155-594, and installation kit no. 001932-005.
® SULLAIR ®
SECTION 8
8.5 COMPRESSOR, FRAME AND DRIVE, 4500 MODEL
02250153_265r01

® SULLAIR ®
PARTS LISTS
8.5 COMPRESSOR, FRAME AND DRIVE, 4500 MODEL (CONTINUED)

1 frame, 37kw 02250151-176 1
2 isolator, vibration air end 50hp 02250151-499 2
3 adapter, compr/motor 50hp ma 02250151-630 1
4 isolator, vibration motor/airend 50/60hp 02250151-941 2
5 grille, coupling guard 50hp 02250152-346 2
8 element, cplg falk 20r 02250152-670 1
9 cover, cplg element falk 20r 02250152-678 1
11 plate, motor seal 3000/3700/4500 02250156-393 2
12 nut, hex metric m12 x 1.75 825912-175 2
15 capscrew, hex gr5 5/8-11 x 1 3/4 829110-175 8
18 washer, iso 7093-8-140hv 865708-240 8
20 nipple, pipe-xs plt 1/2 x cl 866408-000 1
24 motor – (I) 1

A3 To Receiver Tank

program, contact your nearest Sullair representative or the Sullair Corporation.
The shaft seal is not considered part of the compressor unit in regard to the two year warranty, but the normal Sullair parts
warranty does apply. For shaft seal repairs, order repair kit no. 02250050-363, and installation kit no. 602542-001.
® SULLAIR ®
SECTION 8
8.6 AIR INLET SYSTEM, STANDARD 3000P, 3700 AND 4500 SERIES
02250152-457r01
A1

® SULLAIR ®
PARTS LISTS
8.6 AIR INLET SYSTEM, STANDARD 3000P, 3700 AND 4500 SERIES
(CONTINUED)
1 filter, air 9" 02250127-683 (I) 1
2 hose, rubber el 120deg 4"inl ws37 02250156-927 1
3 clamp, hose 4.25" — 5.12" i.d. 02250164–153 2
4 indicator, restriction 20" h20 250003-869 1
5 nut, serr flng m8x1.25 882508-125 2

A1 To Air Inlet on Compressor Unit

(I) For maintenance on air filter No. 02250127-683, order replacement element No. 02250127-684.
® SULLAIR ®
SECTION 8
8.7 AIR INLET SYSTEM, 10 SERIES 3000
A1
02250160-069R02

® SULLAIR ®
PARTS LISTS
8.7 AIR INLET SYSTEM, 10 SERIES 3000 (CONTINUED)

1 filter, air 8"(plastic) w/mtg & + 02250125-369 (I) 1
2 hose, rubber el 3-1/2"-3" 3000 w/+ 02250160-073 1
3 support, air filter 3000 w/10series 02250160-721 1
4 indicator, restriction 20" h20 250003-869 1
5 clamp, hose 2-13/16 to 3-3/4" 250018-550 1
6 clamp, hose 4.25/3.31 250031-415 1
7 nut,serr flng m8 x 1.25 882508-125 4

A1 To Air Inlet on Compressor Unit

(I) For maintenance on air filter No. 02250125-369, order replacement element No. 02250125-372.
® SULLAIR ®
SECTION 8
8.8 AIR PIPING, AIR-COOLED
A1
A3
A2
02250152_474r02

® SULLAIR ®
PARTS LISTS
8.8 AIR PIPING, AIR-COOLED (CONTINUED)

1 tube, mpv/clr/moist sep ls12 02250121-707 1
2 separator, water 1-1/2" fnpt 1/4" drn 02250144-635 (I) 1
3 support, outlet conn 1-1/2npt 02250152-215 1
4 tube, mpv to a/c 1.5" orfs 3700 02250157-836 1
5 tube, a/c to trap 1.5" orfs 3700 02250157-837 1
6 connector, tube-m 1 1/2 x 1 1/2 810224-150 2
7 elbow, tube 90 deg m 1 1/2 x 1 1/2 810524-150 1
8 elbow, tube str thrd 1 1/2 x 1 7/8 811624-188 1
9 nut, serr flng m8 x 1.25 882508–125 2
11 elbow, met st thd/orfs m48 x 1 1/2 883648-024 2

A1 To Aftercooler
A2 From Aftercooler
A3 From Minimum Pressure Valve

(I) For maintenance on water separator No. 02250144-635, order seal replacement element No. 02250144-735.
® SULLAIR ®
SECTION 8
8.9 AIR PIPING, WATER-COOLED

A1
A2
A3
02250 155-292r05

® SULLAIR ®
PARTS LISTS
8.9 AIR PIPING, WATER-COOLED (CONTINUED)

1 separator, water d-h 1-1/2" fnpt 1/4" drn 02250144-635 (I) 1
2 support, outlet conn 1-1/2npt 02250152-215 1
3 tube, mpv to aftrclr 3700 wc 02250155-282 1
4 tube, aftrclr to outlet 3700 wc 02250155-283 1
5 connector, tube-m 1 1/2 x 1 1/2 810224-150 2
6 elbow, tube 90 deg m 1 1/2 x 1 1/2 810524-150 1
7 connector, tube str thd 1 1/2 x 1 7/8 811624-188 1
8 elbow, pipe 90 deg plt 1 1/2" 866215-060 1
9 nipple, pipe-xs plt 1 1/2 x cl 866424-000 1
10 nipple, pipe-xs plt 1 1/2 x 2 866424-020 1
11 nut, serr flng m8 x 1.25 882508–125 2
12 screw, tf-hex m8 x 16 blk zinc 883008-016 2

A1 To Aftercooler
A2 From Aftercooler
A3 From Minimum Pressure Valve

(I) For maintenance on water separator no. 02250144-635, order replacement seal kit no. 02250144-735.
® SULLAIR ®
SECTION 8
8.10 FLUID PIPING, AIR-COOLED

13
8 3 10
12
6
11
2
4 5
02250152-488r00

® SULLAIR ®
PARTS LISTS
8.10 FLUID PIPING, AIR-COOLED (CONTINUED)

1 hose, medium pressure orfs f-swvl 1" x 53" 02250141-104 1
2 hose, medium pressure orfs f-swvl 1" x 48" 02250143-476 1
3 block, thermal valve 50HP 02250151-498 1
4 connector, orfs x metr oring 3/4" 50HP 02250152-223 1
5 elbow, 90 1" sae x 3/4" orfs 02250152-544 1
6 filter, coreless m27 6" 02250155-708 (I) 1
7 o-ring, viton 13/16 x 1/8 826502-211 2
8 o-ring, viton 1 5/16 x 1/8 826502-219 1
9 screw, socket iso m10 x 85mm pc 12.9 874510-085 2
10 connector, metr str thd/orfs m27 x 3/4 883527-012 1
11 elbow, met st thd/orfs m27 x 3/4 883627-012 1
12 union, str thd iso 6149 m27 x 2 883727-012 1
13 element, thermal valve (Sullube) 02250092–081 (II) 1
element, thermal valve (24KT or 175 psig) 02250148–796 (III) 1

A1 To Cooler
A2 To Compressor Unit
A3 From Receiver Tank

(I) For maintenance on coreless filter No. 02250155-708, order replacement element No. 02250155-709.
(II) For maintenance on thermal valves on machines using Sullube, order repair kit no. 02250144-327.
(III) For maintenance on thermal valves on machines using 24KT fluid, or rated 175 psig, order repair kit no. 02250148-827.
® SULLAIR ®
SECTION 8
8.11 FLUID PIPING, WATER-COOLED
A1
A2
A5
A3
A4
02250 155-507r02

® SULLAIR ®
PARTS LISTS
8.11 FLUID PIPING, WATER-COOLED (CONTINUED)

1 adapter, sae 1 5/16 x 1 5/16-12 02250086-022 1
2 connector, sae x orfs .75" 02250135-568 1
3 hose, medium pressure orfs f-swvl 3/4"x 53" 02250141-104 1
4 elbow, 90 1"sae x 3/4"orfs 02250152-544 2
5 housing, thermal valve 50hp w/c 02250155-141 1
6 filter, coreless m27 6"l 02250155-708 1
7 hose, medium pressure orfs f-swvl 3/4" x 54" 02250156-913 1
8 tee, iso-6149/npt oil ret 3700 02250160-059 1
11 o-ring, viton 1 5/16 x 1/8" 826502-219 1
12 plug, pipe 1/4" 3000# stl plt 866900-010 1
13 connector, metr str thd/orfs m27 x 3/4 883527-012 2
14 elbow, met st thd/orfs m27 x 3/4 883627-012 2
15 union, str thd iso 6149 m27 x 2 883727-012 2
16 valve, thermal 195f 1 1/2-18 (Sullube) 02250092-081 (I) 1
element, thermal 210f (24kt, 175 psig) 02250148-796 (I) 1

A1 From Fluid Cooler Outlet
A2 To Fluid Cooler Inlet
A3 Fluid Return From Receiver Tank
A4 Fluid Injection To Compressor Unit
A5 To Water Regulator Valve

(I) For maintenance on thermal valve no. 02250092-081, order repair kit No. 02250144-327.
For maintenance on thermal valve no. 02250148-796, order repair kit No. 02250148-827.
® SULLAIR ®
SECTION 8
8.12 COOLING AND LUBRICATION SYSTEM, AIR-COOLED 18"/60HZ FAN,

STANDARD COOLER
A4
A3
A1
A2
02250158-442r02

® SULLAIR ®
PARTS LISTS
8.12 COOLING AND LUBRICATION SYSTEM, AIR-COOLED 18"/60HZ FAN,

STANDARD COOLER (CONTINUED)
1 cooler, air/oil 50hp 02250151-493 1
2 duct, centrifugal fan 3700 02250151-496 1
3 support, fan motor 3700 02250151-501 1
4 panel, venturi 3700 18" fan 02250155-681 1
panel, venturi 4500 20" fan 02250155–680 1
5 adapter, venturi 3700 18" fan 02250155-682 1
adapter, venturi 4500 20" fan 02250155–683 1
6 fan, centrifugal hs 60hz 18"dia 02250155-684 1
fan, centrifugal 20" 50HP std 02250151-494 1
fan, centrifugal 18" 60HP hi static/60HP std 02250155-684 1
fan, centrifugal 20" 60HP hi static/50HZ 02250155-685 1
fan, centrifugal 18" 50HP 50HZ 02250151-495 1
7 guard, fan discharge 3700 02250158-544 1
8 weatherstrip, 3/16 x 3/8 ft 250022-436 6
9 nut, hex metric m8 x 1.25 825908-125 4
12 washer, iso 7093-8-140hv 865708-240 12
13 nut,serr flng m8 x 1.25 882508-125 8
16 motor - (I) 1

A1 In From MPV
A2 Out To Water Separator
A3 Thermal Bypass Valve
A4 Cooler Pack Assembly Rest on Top Rails of Canopy. Thread Forming
Screws Attach Cooler Pack To Rails.

(I) This part will vary by model.
® SULLAIR ®
SECTION 8
8.13 FLUID COOLING SYSTEM, WATER-COOLED
A5
A5
A1
A2
A6
A7
A8
A4
A3 02250155_291r05

® SULLAIR ®
PARTS LISTS
8.13 FLUID COOLING SYSTEM, WATER-COOLED (CONTINUED)

1 cooler, ls12v oil/wtr 5 x 36 02250094-744 1
2 valve, solenoid 2wnc 3/4 250# n4 + 02250125-668 (I) (III) 1
3 support, heat exchanger w/c 50hp 02250155-140 1
4 support, water conn 3/4" 3700 w/c 02250155-142 1
5 u-bolt, w/saddle 5.50" 02250155-250 2
6 elbow, tube 3/4"-plstc x 3/4"-npt 02250155-257 (II) (III) 4
7 spacer, stl tube .50 o.d. x .49 02250164-034 4
8 drainlock, 1/4" 40061 2
9 valve, water reg 3/4"160-230f 47398 (II) 1
10 clr, aftrclr 1-1/2" npt air/1" npt wtr port 250017-527 (IV) 1
clr, aftrclr 1-1/2" npt air/1" npt wtr port 250040-680 (V) 1
11 elbow, 90 1/4t pls x 1/4 npt m 250018-430 1
12 clamp, tubing 1-1/8" dia 250025-636 1
13 tubing, thermoplastic 3/4"(ft) 250039-353 7
14 connector, male plastic tubing 3/4x3/4 250039-357 4
16 nipple, pipe pltd 3/4 x 2 1/2 866312-025 1
17 nipple, pipe-xs plt 3/4 x 3 866412-030 2
18 nipple, pipe-xs plt 3/4 x 4 866412-040 (II) 1
19 bushing, red hex pltd 3/8 x 1/4 868901-010 1
20 bushing, red hex pltd 1 x 3/4 868904-030 4
21 elbow, pipe 90f 1/4 x 1/4 brass 881104-025 2
22 nipple, pipe-hx brass 3/8 x 1/4 881306-025 2
23 nut,serr flng m8 x 1.25 882508-125 9

A1 To Water Separator
A2 To Minimum Pressure Valve
A3 Water In
A4 Water Out
A5 Air Bleed Valve
A6 To PSW2 low Water Pressure Switch in Electrical Control Box
A7 To Fluid Cooler
A8 From Fluid Cooler

(I) For maintenance on solenoid valve No. 02250125-668, order repair kit No. 02250160-751, and replacement coil No.
02250125-855.
(II) Used on machines requiring water regulating valve option.
(III) Used on machines requiring water solenoid valve option.
(IV) 3000, 3700 models only.
(V) 4500 model only.
® SULLAIR ®
SECTION 8
8.14 DISCHARGE, RECEIVER AND PIPING SYSTEM, 3000P, 3700 AND 4500
A2
A1
A3
A7
A4
A6 A5
02250152_600r03

® SULLAIR ®
PARTS LISTS
(CONTINUED)
1 adapter, sae 1 7/8-12 x 1 7/8-12 02250055-014 1
2 vlv. min press chk 1-7/8 sae 0-ring 02250097-598 (I) 2
3 plug, sight glass 1 5/16" sae 02250097-610 1
4 elb, 90 deg 3/4 sae x 3/8 nptf 02250100-093 1
5 adapter, sae 7/16 x 7/16-20 02250101-783 1
6 filter, assembly screen filter 02250117-782 (II) 1
7 orifice, plug brass 1/8"npt x 1/32" 02250125-774 1
8 sightglass, orf block sae 02250126-129 1
9 valve, ball mini m x f 3/8"viton 02250146-870 1
10 tank, separator 3700 02250149-624 1
11 joint, expansion air end-separator 02250151-492 1
12 elbow, sae 1/4" (7/16-20) m x f 02250152-798 1
13 flange, kit sae split 2" m12 bolt 02250152-810 2
14 spring, conical oil sep ground 02250155-720 1
15 isolator, vibration 3700 02250156-379 4
16 wire,10 gage ground bond 12" m8 02250157-450 1
17 element, sep round 5.5d x 14.3lng 02250160-774 (III) 1
18 support, receiver 3700 shipping 02250162-937 1
19 plug, o-ring boss sae 1 1/4 40029 1
20 clamp, speed tube 1/4" 43357 1
21 valve, pressure relief 200 psig 250006-938 1
22 nut, hex metric m8 x 1.25 825908-125 4
23 o-ring, viton 7 3/4 x 3/16" 826502-368 1
26 tubing, stnls stl 1/4 20ga ft 841215-004 4
28 connector, tube-m 1/4 x 1/4 ss 876804-025 1
29 elbow, tube 90 deg m 1/4 x 1/4 ss 877004-025 1
30 nut,serr flng m8 x 1.25 882508-125 1
® SULLAIR ®
SECTION 8
(CONTINUED)
A2
A1
A3
A7
A4
A6 A5
02250152_600r03

® SULLAIR ®
PARTS LISTS
(CONTINUED)
A1 To Strainer on Solenoid Valve Assembly
A2 To Aftercooler In
A3 To Unit Oil Return Port
A4 From Unit Discharge
A5 To Grounding Location on Frame
A6 To Frame
A7 Sump Pressure

(I) For maintenance on minimum pressure valve no. 02250097-598, order:
kit, repair, No. 02250110-727
kit, cap, No. 02250046-396
kit, O-ring, No. 02250048-363
kit, piston , No. 02250051-337
(II) For maintenance on return line strainer, order replacement strainer No. 02250117-782.
(III) For maintenance on separator element No. 02250160-774, order replacement element No. 02250160-776.
® SULLAIR ®
SECTION 8
8.15 DISCHARGE, RECEIVER AND PIPING, 3000 WITH 10 SERIES UNIT
A2
A1
A7
A3
A4
A5
A6 02250160_070r03

® SULLAIR ®
PARTS LISTS

(CONTINUED)
1 adapter, sae 1 7/8-12 x 1 7/8-12 02250055-014 1
2 vlv. min press chk 1-7/8 sae 0-ring por 02250097-598 (I) 1
3 plug, sight glass 1 5/16" sae 02250097-610 1
4 elb, 90 deg 3/4 sae x 3/8 np 02250100-093 1
5 adapter, sae 7/16 x 7/16-20 02250101-783 1
6 filter, assembly screen filter 02250117-782 (II) 1
7 orifice, plug brass 1/8"npt x 1/32" 02250125-774 1
8 sightglass, orf block sae 02250126-129 1
9 valve, ball mini m x f 3/8"viton 02250146-870 1
10 tank, separator ws37 02250149-624 1
11 elbow, sae 1/4" (7/16-20) m x f 02250152-798 1
12 flange, kit sae split 2" m12 bolt 02250152-810 1
13 spring, conical oil sep ground ws 02250155-720 1
14 isolator, vibration ws 30/37/45 rec tnk 02250156-379 4
15 wire, 10 gage ground bond 12" m8 02250157-450 1
16 joint, expansion 3700 w/10series unit 02250159-974 1
17 element, sep round 5.5d x 14.3lng+ 02250160-774 (III) 1
18 support, receiver 3700 shipping 02250162-937 1
19 plug, o-ring boss sae 1 1/4 40029 1
20 clamp, speed tube 1/4" 43357 1
21 valve, pressure relief 200 psig 250006-938 1
22 nut, hex metric m8 x 1.25 825908-125 4
23 o-ring, viton 7 3/4 x 3/16" 826502-368 1
26 tubing, stnls stl 1/4 20ga ft 841215-004 4
28 connector, tube-m 1/4 x 1/4 ss 876804-025 1
29 elbow, tube 90 deg m 1/4 x 1/4 ss 877004-025 1
30 nut,serr flng m8 x 1.25 882508-125 1
34 connector, straight thd/orfs 1 7/8 x 1 1/2 884424-188 1
® SULLAIR ®
SECTION 8

(CONTINUED)
A2
A1
A7
A3
A4
A5
A6 02250160_070r03

® SULLAIR ®
PARTS LISTS

(CONTINUED)
A1 To Strainer on Solenoid Valve Assembly
A2 To Aftercooler In
A3 To Unit Oil Return Port
A4 From Unit Discharge
A5 To Grounding Location on Frame
A6 To Frame
A7 Sump Pressure

(I) For maintenance on minimum pressure valve no. 02250097-598, order:
kit, repair, No. 02250110-727
kit, cap, No. 02250046-396
kit, O-ring, No. 02250048-363
kit, piston , No. 02250051-337
(II) For maintenance on return line strainer, order: strainer No. 02250117-782, (qty of 2 needed).
(III) For maintenance on separator element No. 02250160-774, order: element No. 02250160-776.
® SULLAIR ®
SECTION 8
8.16 MOISTURE DRAIN
02250152_494r01

® SULLAIR ®
PARTS LISTS
8.16 MOISTURE DRAIN (CONTINUED)

1 locknut, n4 conduit sealing 02250071-362 4
2 valve, solenoid 2wnc 1/4 200# 24vdc 02250155-715 (I) 1
3 valve, ball 1/4" npt 047115 1
4 strainer, v-type 300psix1/4 241771 (II) 1
5 nipple, conduit 1/2 x 1.125" 250007-168 1
6 elbow, 90deg m swvl 1/4t x 1/4 npt 250025-850 1
7 connector, male1/4tube x 1/4 250025-859 1
8 hose,nylon 1/4(ft) 842215-004 5
9 conduit 846315-050 4
10 elbow, 45deg lq-tite 1/2 846500-050 1
11 elbow, 90deg lq-tite 1/2 846600-050 1
12 elbow, entrance 1/2 847715-050 1
13 elbow, pipe-90m 1/4 x 1/4 brass 881004-025 1

A1 To Air Bracket Out
A2 To Water Seperator
A3 To Bottom of Starter Box
A4 Port 1
A5 Port 2

(I) For maintenance on solenoid valve no. 02250155-715, order repair kit no. 02250157-501, and replacement coil no.
02250157-502.
(II) For maintenance on return line strainer no. 241771, order repair kit no. 241772.
® SULLAIR ®
SECTION 8
8.17 PNEUMATIC CONTROL SYSTEM, WITH STANDARD SEQUENCING
A3
A4
A1 A3
A2 A4
A7
A1 A2
A8
A7
A5
A9
A6
02250163_528r03

® SULLAIR ®
PARTS LISTS
8.17 PNEUMATIC CONTROL SYSTEM, WITH STANDARD SEQUENCING

(CONTINUED)
1 locknut, n4 conduit sealing 02250071-362 2
2 valve, 1/2 bldwn 1.8:1 250 psig 02250100-042 (I) 1
3 valve, check 1/4" poppet style 02250115-272 1
4 valve, solenoid 3wno 1/4 250# 24vdc 02250155-714 (II) 2
5 tbg, nylon 1/4"-od red 02250155-961 3
6 tbg, nylon 1/4"-od blue 02250155-962 2
7 tbg, nylon 1/4"-od yellow 02250155-963 5
8 orifice,.140".25 fnpt x .25 02250161-433 1
9 strainer, v-type 300psix1/4 241771 (III) 1
10 hose, med press 0.50 x 015" 249608-019 1
11 valve, pressure regulator 250017-280 (IV) 1
12 elbow, 1/4" tube x 1/4" npt 250018-430 2
13 tee, male branch swiv 1/4 tube x 1/4 npt 250025-835 1
14 elbow, 90deg m swvl 1/4t x 1/8npt 250025-849 (V) 1
15 elbow, 90deg m swvl 1/4t x 1/4 npt 250025-850 8
16 connector, male1/4tube x 1/4 250025-859 1
17 connector, fem tube 1/4 x 1/4 nptf 250025-923 1
18 valve, shuttle 1/4" npt (dbl chk) 408893 1
19 adapter, fem pipe 1/4 x 7/16-20 811502-025 (V) 1
20 nipple, chase cond 1/2 847815-050 2
21 elbow, 37fl 90m 1/2 x 1/2 860208-050 1
22 elbow, pipe-90m 1/2 x 1/2 860508-050 1
23 tee, male pipe brass 1/4 869825-025 2
24 connector,37 fl 1/2 x 1/4" npt 873704-075 1

A1 Port 1
A2 Port 2
A3 Port 3
A4 To Starter Box
A5 To Inlet Valve
A6 To Inlet Adapter
A7 To Reciever Tank
A8 To Starter Below Inlet
A9 Flow Direction
(I) For maintenance on blowdown valve no. 02250100-042, order: repair kit no. 02250100-042.
(II) For maintenance on solenoid valve no. 02250155-714, order: repair kit no. 02250155-500, and replacement coil no.
02250157-502.
(III) For maintenance on strainer no. 241771, order: repair kit no. 241772.
(IV) For maintenance on pressure regulator valve no. 250017-280, order: repair kit no. 250019-453.
(V) Use with 3000 machine only.
® SULLAIR ®
SECTION 8
8.18 CONTROL SYSTEM AND ELECTRIC PARTS, MFV

A7
A6
A3
A4
A5
A2
A1
A8 02250156_145r02

® SULLAIR ®
PARTS LISTS
8.18 CONTROL SYSTEM AND ELECTRIC PARTS, MFV (CONTINUED)

1 tube, nyl .25 x 040w blk (ft) 02250054-861 (I) 2
2 locknut, n4 conduit sealing 02250071-362 (I) 1
3 grip, cord n4 .125-.187 x 1/2" 02250071-379 1
4 grip, cord n4 .250-.375 x 1/2" 02250071-381 2
5 nameplate, e-stop 45mm yellow 02250081-473 1
6 transformer, control 150va univ w.pri fh 02250083-186 1
7 switch, push-button operator e22 40mm 02250085-504 1
8 bar, ground 5 post cutler hammer 02250101-721 2
9 control, display s4 02250154-051 1
10 control, i/o mod ws 24vdc supply 02250154-052 1
11 decal, microprocessor overlay 02250154-359 1
12 block, contact aux 1nc ch-it a-e 02250154-608 1
13 transducer, pressure 0-250# ratiometric 02250155-174 2
14 probe, rtd 100 ohm plat 3.5"x 6ft 02250155-175 1
15 specification, encl 3700 22"x36"x10" 02250155-936 1
17 receptacle,s4 program port nema 6p 02250159-547 1
18 cap, s4 program port nema 6p 02250159-549 1
19 spacer, p8/p12 ws mtg to encl 02250161-759 4
20 breaker, cir100a hmcp 250014-827 1
21 switch, pressure n.o. 10 psi 250017-992 (I) 1
22 elbow, 90 1/4"tube x 1/8"npt 250018-429 (I) 1
23 fuse, limitron ktk-r 2.00 250019-756 (I) 1
24 relay, overload 32a 250021-692 (II) 1
25 adapter, o.l.r. base mnt ch1 250021-694 (II) 1
27 block, contact 1nc 250027-125 1
28 fitting, compress adj 250028-635 1
29 plug, hole n4 1/2" cond 409918-002 2
30 nut, hex metric m8 x 1.25 825908-125 6
31 lug, scrulug kpa-25 4-1/0 849215-025 2
32 terminal, ring tng 3/8 x 8ga 849306-008 1
34 starter, ac fan - (II) (III) 1
35 fuse - (I) (III) 2
36 block, power - (III) 1
37 supply, power - (III) 1

® SULLAIR ®
SECTION 8

A7
A6
A3
A4
A5
A2
A1
A8 02250156_145r02

® SULLAIR ®
PARTS LISTS

A1 P1 - Wet Receiver Pressure
A2 P2 - Line Pressure
A3 Solenoid 1
A4 Solenoid 4
A5 T1 - Wet Discharge Temp
A6 PSW2 - Low Water Pressure Switch
A7 Drill Hole for WC Machine
A8 To Frame

(I) Denotes water-cooled machines only.
(II) Denotes air-cooled machines only.
(III) This part may vary per machine specification. Consult the Sullair factory for details.
® SULLAIR ®
SECTION 8
8.19 CONTROL SYSTEM AND ELECTRIC PARTS, WYE-DELTA

A7
A6
A3
A4
A5
A2
A1
02250152_491r03
A8

® SULLAIR ®
PARTS LISTS
8.19 CONTROL SYSTEM AND ELECTRIC PARTS, WYE-DELTA (CONTINUED)

3 grip, cord n4 .125-.187 x 1/2" 02250071-379 1
4 grip, cord n4 .250-.375 x 1/2" 02250071-381 2
6 transformer, control 150va univ w.pri fh 02250083-186 (I) 1
12 block, contact aux 1no ch-it a-e 02250154-607 1
13 block, contact aux 1nc ch-it a-e 02250154-608 2
16 link, mech intrlk ch it frm b-e 02250155-676 1
17 specification, encl 3700 22"x36"x10" 02250155-936 1
19 receptacle,s4 program port nema 6p 02250159-547 1
23 elbow, 90 1/4"tube x 1/8"npt 250018-429 (I) 1
24 relay, overload 32a 250021-692 (II) 1
25 adapter, o.l.r. base mnt ch1 250021-694 (II) 1
27 fuse, kldr 1.50 600v td 250026-643 (I) 2
30 plug, hole n4 1/2" cond 409918-002 2
31 nut, hex metric m8 x 1.25 825908-125 6
32 lug, scrulug kpa-25 4-1/0 849215-025 2
36 contactor - (III) 2
37 fuse - (I) (III) 1
® SULLAIR ®
SECTION 8

A7
A6
A3
A4
A5
A2
A1
02250152_491r03
A8

® SULLAIR ®
PARTS LISTS

A1 P1 - Wet Receiver Pressure
A2 P2 - Line Pressure
A3 Solenoid 1
A4 Solenoid 4
A5 T1 - Wet Discharge Temp
A6 PSW2 - Low Water Pressure Switch
A7 Drill Hole for WC Machine
A8 To Frame

® SULLAIR ®
SECTION 8
8.20 CONTROL SYSTEM AND ELECTRIC PARTS, VSD

A7
A6
A3
A4
A5
A2
A1
A8 02250156_144r02

® SULLAIR ®
PARTS LISTS
8.20 CONTROL SYSTEM AND ELECTRIC PARTS, VSD (CONTINUED)

2 rail, din 35mm (meters) 02250060-705 (I) 1
4 grip, cord n4 .125-.187 x 1/2" 02250071-379 1
5 grip, cord n4 .250-.375 x 1/2" 02250071-381 2
7 transformer, control 150va univ w.pri fh 02250083-186 (I) 1
10 relay, sptd din 6a 24vdc coil 02250140-490 (I) 1
16 specification, encl 3700v 22" x 36" x 10 02250155-937 1
18 receptacle, s4 program port nema 6p 02250159-547 1
22 elbow, 90 1/4"tube x 1/8"npt 250018-429 (I) 1
23 fuse, limitron ktk-r 2.00 250019-756 (I) 1
24 holder, fuse ktk-r 3 pole 250019-773 (II) 1
28 fu, cc td 10a 600vac 250041-618 3
29 plug, hole n4 1/2" cond 409918-002 (II) 2
30 nut, hex metric m8 x 1.25 825908-125 6
31 lug, scrulug kpa-25 4-1/0 849215-025 1
35 fuse - (I) (III) 2
38 vsd - (III) 1

® SULLAIR ®
SECTION 8

A7
A6
A3
A4
A5
A2
A1
A8 02250156_144r02

® SULLAIR ®
PARTS LISTS

A1 P1- Wet Receiver Pressure
A2 P2- Line Pressure
A3 Solenoid 1
A4 Solenoid 4
A5 T1-Wet Discharge Temperature
A6 PSW2- Low Water Pressure
A7 Drill Hole for WC machines
A8 To Frame

® SULLAIR ®
SECTION 8
8.21 ENCLOSURE, AIR-COOLED
02250155_297r03

® SULLAIR ®
PARTS LISTS
8.21 ENCLOSURE, AIR-COOLED (CONTINUED)

1 cap, molded canopy corner 02250150-893 4
2 rail, vertical 3000,3700,4500 02250150-910 3
3 rail, roof air out end 37kw 02250150-912 1
4 gusset, str crnr square 37kw 02250151-177 1
5 panel, canopy door flanged w/cutout 02250151-178 1
6 panel, canopy door flanged 37kw 02250151-179 1
7 panel, starter end bottom 3700 02250151-180 1
8 panel, canopy door locking 37kw 02250151-181 2
9 panel, canopy assy intake end 37kw 02250151-182 1
10 panel, roof canopy 37kw 02250151-183 1
11 bearing, flanged 5mm 50hp 02250151-635 4
12 panel, starter end l/h 37kw 02250152-031 1
13 rail, roof starter end 37kw 02250152-040 1
14 insulation, foam 2" corner piece 50h 02250152-323 4
15 gusset, corner square 37kw 02250154-298 3
16 rail, vertical starter side 3700 02250154-393 1
17 cover, forkpocket 37kw 02250154-405 8
18 rail, side assy rh/lh 37kw 02250154-992 2
19 support, shipping mtr/unit 37kw 02250155-191 1
20 plug, hole 2 1/2" nylon black 02250155-284 1
21 pocket, drawing holder 3700 02250158-039 1
23 trim, canopy edge 7.5/10hp 250034-157 2

A1 Clean Air Inlet Filter 3700 02250161-137 1
® SULLAIR ®
SECTION 8
8.22 ENCLOSURE, WATER-COOLED
02250155_298r03

® SULLAIR ®
PARTS LISTS
8.22 ENCLOSURE, WATER-COOLED (CONTINUED)

1 cap, molded canopy corner 02250150-893 4
2 rail, vertical 3000,3700,4500 02250150-910 3
3 rail, roof air out end 37kw 02250150-912 1
4 gusset, str crnr square 37kw 02250151-177 1
5 panel, canopy door flanged w/cutout 02250151-178 1
6 panel, canopy door flanged 37kw 02250151-179 1
7 panel, starter end bottom 3700 02250151-180 1
8 panel, canopy door locking 37kw 02250151-181 2
9 bearing, flanged 5mm 50hp 02250151-635 4
10 panel, starter end l/h 37kw 02250152-031 1
11 rail, roof starter end 37kw 02250152-040 1
12 insulation, foam 2" corner piece 50h 02250152-323 4
13 gusset, corner square 37kw 02250154-298 3
14 rail, vertical starter side 3700 02250154-393 1
15 cover, forkpocket 37kw 02250154-405 8
16 rail, side assy rh/lh 37kw 02250154-992 2
17 support, shipping mtr/unit 37kw 02250155-191 1
18 panel, roof canopy w/c 02250155-204 1
19 panel, baffle canopy w/c 02250155-205 1
20 panel, canopy assy intake 37kw w/c 02250155-260 1
21 plug, hole 2 1/2" nylon black 02250155-284 1
22 pocket, drawing holder 3700 02250158-039 1
23 guard, fan 13"dia 241579 1
24 fan, enclosure 10s wc 241580 1
26 trim, canopy edge 7.5/10hp 250034-157 2
27 nut, serr flng m8 x 1.25 882508-125 8

A1 Cooling Fan Baffle
A2 Aftercooler Mounting Feet
A3 Oil Cooler Mounting Feet
A4 Clean Air Inlet Filter 3700 02250164-592 1
® SULLAIR ®
SECTION 8
8.23 DECAL LOCATIONS, AIR-COOLED

A1 A6 20 A1 A6
A4
20
A7
A5 A8
A3
A2
A2
A1
A4
A1
A8
A4
A1 A1
A7
02250152_489r05
A7

® SULLAIR ®
PARTS LISTS
8.23 DECAL LOCATIONS, AIR-COOLED (CONTINUED)

1 decal, iso 9001 blk 3.44x5.75 02250057-624 1
2 decal, protective earth ground 02250075-045 (III) 2
3 decal, pe designation 02250075-540 (III) 1
4 decal, electrocution hazard international/global 02250077-472 1
5 decal, en-warning mixing fluids 02250110-891 1
6 decal, parallel wye motor conn. 02250146-385 2
8 decal, sullair side graphic 50hp 02250154-360 1
9 decal, sullair side graph 50hp 02250154-361 2
10 decal, black www.sullair.com 02250155-495 2
11 decal, maint kit eng 3700 02250156-300 1
12 decal, remove before start-up 02250158-358 (IV) 2
13 decal, vsd black p8/p10/p12 02250162-215 2
14 decal, warning n12 elec encl protc 02250164-823 1
15 decal, warning auto start 41065 1
16 decal, danger hi voltage 42218 (I) 1
17 sign, warning-comp oil fil cap 49685 1
18 decal, danger electrocution 49850 1
19 decal, warning elect. shock-ground fault 49852 (II) 1
20 sign, warning-sever-fan-indus 49855 3
21 decal, fork lifting 241814 4
22 decal, warn "food grade" lube 250003-144 1
23 decal, warning-autostart 250017-903 1
24 decal, water in 250019-107 1
25 decal, water out 250019-108 1
26 decal, rotation 3.5" lg 250021-564 2
27 decal, water drain 3 3/4 x 1" 250022-810 1
28 decal, danger inhaling comp air 250027-935 1
29 sign, warning-hot surfaces 407408 1
30 decal, fluid – (V) 1
31 nameplate – (V) 1
32 rivet – (V) 4
33 decal, series – (V) 2
34 decal, voltage – (I) (V) 1
® SULLAIR ®
SECTION 8

A1 A6 20 A1 A6
A4
20
A7
A5 A8
A3
A2
A2
A1
A4
A1
A8
A4
A1 A1
A7
02250152_489r05
A7

® SULLAIR ®
PARTS LISTS

A1 Both Sides of Machine
A2 Center Stripes Vertically Based on Location of WS Controller Decal
A3 Locate Decals on both Sides of Machine by Using Location of End Stripe and WS Controller Location
A4 Used Only On VSD Machines
A5 Used On Parallel Wye Machines Only
A6 Air-cooled Only
A7 Water-cooled Only
A8 Not used on 575V VSD machines

(I) Attach to the bottom on inside of starter box.
(II) Attach to inside of starter door.
(III) Attach to sub-panel inside starter box.
(IV) Attach to top of shipping strap.
(V) This part will vary by model. Consult factory with serial number.
® SULLAIR ®
SECTION 8
8.24 DECAL LOCATIONS, WATER-COOLED
A5
A1 A3 A1 A2
A1
A4
A1 A1
02250163_167r01

® SULLAIR ®
PARTS LISTS
8.24 DECAL LOCATIONS, WATER-COOLED (CONTINUED)

1 decal, iso 9001 blk 3.44x5 75 02250057-624 1
2 npl, sullair serial number 02250059-318 1
3 decal, protective earth ground 02250075-045 (III) 2
4 decal, pe designation 02250075-540 (III) 1
5 decal, electrocution hazard international/glbl 02250077-472 1
7 decal, parallel wye motor conn. 02250146-385 2
9 decal, sullair side graphic 50 hp 02250154-360 1
10 decal, sullair side graph 50hp 02250154-361 2
13 decal, remove before start-up 02250158-358 (IV) 2
14 decal, vsd black p8/p10/p12 02250162-215 2
15 decal, warning auto start 41065 1
16 decal, danger hi voltage 42218 (I) 1
18 decal, danger electrocution 49850 1
19 decal, warning elect. shock-ground fault 49852 (II) 1
24 decal, water in 250019-107 1
25 decal, water out 250019-108 1
30 rivet, pop 1/8 x 1/2 843102-050 4
31 decal, fluid FLUID DECAL 1
32 decal, series SERIES DECAL 2
33 decal, voltage VOLTAGE DECAL (I) 1
® SULLAIR ®
SECTION 8
A5
A1 A3 A1 A2
A1
A4
A1 A1
02250163_167r01

® SULLAIR ®
PARTS LISTS

A1 Both Sides Of Machine
A2 Center Stripes Vertically Based On Location Of WS Controller Decal
A3 Locate Decals On Both Sides Of Machine By Using Location Of End Stripe And WS Controller Location
A4 Used On VSD Machines Only
A5 Used On Parallel Wye Machines Only

(I) Attached to the bottom on inside of starter box.
(II) Attached to inside of starter door.
(III) Attached to sub-panel inside starter box.
(IV) Attached to top of shipping strap.
(VIII) This part may vary per machine specification. Consult the Sullair factory for details.
® SULLAIR ®
SECTION 8
8.25 DECAL GROUP

1 2 3 4
7
6
5 8
02250155_601_Decal_1

® SULLAIR ®
PARTS LISTS
8.25 DECAL GROUP (CONTINUED)

3 sign, warning ground fault 049852 1
6 sign, danger electrocution 049850 1
® SULLAIR ®
SECTION 8

9 10
11
12
13
14
16
17
15
18
02250155_601_Decal_2

® SULLAIR ®
PARTS LISTS

9 decal, caution auto start 041065 1
10 decal, danger hi voltage 042218 1
12 decal, electrocution hazard international/globa 02250077-472 1
13 decal, protective earth ground 02250075-045 2
14 decal, fluid Sullube 02250069-389 (I) 1
18 decal, ISO 9001 blk 3.44x5.75 02250057-624 1

(I) Although Sullube fluid decal is shown, initial fluid fill may vary by machine. For correct corresponding fluid decal part number,
consult factory with serial numbers of your machine.
CAUTION
warranties.
® SULLAIR ®
SECTION 8

29
19
20 30
21
31
22
23 32
24
33
25
34
26
37
27
28
02250155_601_Decal_3

® SULLAIR ®
PARTS LISTS

20 decal, black graphic 02250157-732 1
21 decal, side graphics 02250157-703 1
24 decal, VSD (variable speed drive) 02250162-215 1
25 decal, 3000 with stripe 02250157-029 1
26 decal, 3000P with stripe 02250166-030 1
29 decal, remove before start up 02250158-358 1
30 decal, voltage 460/3/60 international 02250569-399 (I) 1
31 decal, voltage 380-415/3/50 international 02250069-403 (I) 1
35 nameplate, Sullair serial number 02250059-318 (II) 1
36 rivet, pop 1/8 x 1/2 843102-050 (III) 4
37 decal, warning n12 elec encl protection 02250164–823 1

(I) This decal may vary per machine specification. Consult the Sullair factory for details.
(II) See Figure 8-1 for features and location.
(III) This part not shown.
® SULLAIR ®
SECTION 8

® SULLAIR ®
®
WORLDWIDE SALES AND SERVICE

SULLAIR ASIA, LTD. SULLAIR CORPORATION SULLAIR EUROPE, S.A.
Sullair Road, No. 1 3700 East Michigan Boulevard Zone Des Granges BP 82
Chiwan, Shekou Michigan City, Indiana 46360 U.S.A. 42602 Montbrison Cedex, France
Shenzhen, Guangdong PRV. Telephone: 33-477968470
PRC POST CODE 518068
www.sullair.com
Fax: 33-477968499
Telephone: 1-800-SULLAIR (U.S.A. Only)
Telephone: 755-6851686 www.sullaireurope.com
or 1-219-879-5451
Fax: 755-6853473
Fax: (219) 874-1273
www.sullair-asia.com
CUSTOMER CARE
for PARTS and SERVICE
1-888-SULLAIR (7855247)
219-874-1835
CHAMPION COMPRESSORS, LTD.

Princess Highway
Hallam, Victoria 3803
Austrailia
Telephone: 61-3-9796-4000
Fax: 61-3-9703-8053
www.championcompressors.com.au
Printed in the U.S.A

Specifications subject to change
without prior notice
E07KCC

ManualsOperator 3007

Uploaded by

Copyright:

Available Formats

ManualsOperator 3007

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ManualsOperator 3007

Uploaded by

Copyright:

Available Formats

O PERATO R’S M ANU AL AND PARTS LIST

INDUSTRIAL AIR COMPRESSOR

AIR CARE SEMINAR TRAINING

For detailed course outlines, schedule and cost information contact:

Sullair Customer Care Training Department

Wiring Diagram, MFV Water-Cooled.........................................................36

iv 3000-4500 Operator’s Manual and Parts List

Recommended Spare Parts List...............................................................73

THIS PAGE INTENTIONALLY LEFT BLANK

vi 3000-4500 Operator’s Manual and Parts List

1.2 PERSONAL PROTECTIVE

2 3000-4500 Operator’s Manual and Parts List

SUBSTANCES 1.8 ELECTRICAL SHOCK

4 3000-4500 Operator’s Manual and Parts List

1. Fluid Filter 8. E-Stop Button

6 3000-4500 Operator’s Manual and Parts List

1. Moisture Separator 8. E-Stop Button

With a Sullair compressor, there is no

8 3000-4500 Operator’s Manual and Parts List

Figure 2-3: Air-Cooled, Cooling / Lubrication and Discharge System

Figure 2-4: Water-Cooled, Cooling / Lubrication and Discharge System

10 3000-4500 Operator’s Manual and Parts List

2.6 CONTROL SYSTEM, Start Mode - 0 to 50 PSIG (0 to 3.5 Bar)

1. Air Outlet 6. Minimum Pressure/Check Valve

12 3000-4500 Operator’s Manual and Parts List

2.7 AIR INLET SYSTEM, WARNING

14 3000-4500 Operator’s Manual and Parts List

1. Air Inlet Filter 4. Receiver Tank

THIS PAGE INTENTIONALLY LEFT BLANK

16 3000-4500 Operator’s Manual and Parts List

3.2 TABLE OF SPECIFICATIONS - VARIABLE SPEED DRIVE MODELS

18 3000-4500 Operator’s Manual and Parts List

3.3 COMPRESSOR SPECIFICATIONS

MOTOR (III): STANDARD MODELS:

3.4 LUBRICATION GUIDE NOTE

If fluid change is required, follow Section 3.6,

at cemented joints. Certain other 1. Fluid Fill Port

20 3000-4500 Operator’s Manual and Parts List

3.6 LUBRICATION CHANGE RECOMMENDATIONS AND MAINTENANCE, FLUID

3.7 IDENTIFICATION, AIR-COOLED, STANDARD AND VSD

22 3000-4500 Operator’s Manual and Parts List

1. Alternate Incoming Power Supply Location 6. Air Inlet

3.8 IDENTIFICATION, WATER-COOLED

24 3000-4500 Operator’s Manual and Parts List

3.9 PIPING AND INSTRUMENTATION, AIR-COOLED

Figure 3-4: Piping and Instrumentation, Air-Cooled

26 3000-4500 Operator’s Manual and Parts List

Key Description Part Number Note Quantity

3.9 PIPING AND INSTRUMENTATION, AIR-COOLED (CONTINUED)

Figure 3-5: Piping and Instrumentation, Air-Cooled

28 3000-4500 Operator’s Manual and Parts List

Key Description Part Number Note Quantity

3.10 PIPING AND INSTRUMENTATION, WATER-COOLED

Figure 3-6: Piping and Instrumentation, Water-Cooled

30 3000-4500 Operator’s Manual and Parts List

Key Description Part Number Note Quantity

3.10 PIPING AND INSTRUMENTATION, WATER-COOLED (CONTINUED)

Figure 3-7: Piping and Instrumentation, Water-Cooled

32 3000-4500 Operator’s Manual and Parts List