Scribd
Upload
29 views

Lab Report: Submitted By: Registration Number: Group Number: Section: Submitted To

In this document different PCB boards are descrobed and their working and especially Arduino NANO is instructed for its making

Uploaded by

Rana Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
29 views

Lab Report: Submitted By: Registration Number: Group Number: Section: Submitted To

In this document different PCB boards are descrobed and their working and especially Arduino NANO is instructed for its making

Uploaded by

Rana Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

Lab Report

Submitted by: ​Student Name: ​ Malik Zain

Registration Number: ​2018-EE-130

Group Number: ​C8

Section: ​C

Submitted to:

Mr. M. Anique Aslam

Mr. Bilal Ahmed


Department of Electrical Engineering

University of Engineering and Technology, Lahore,


Pakistan
EE-101L: Electrical and Electronics
Workshop
Vero Board Projects:

1. Seven-Segment Display:

Component Side:

Figure 1: ​Component side of Seven Segment

Soldering Side:
Figure 2: ​Soldered side of Seven Segment
Display.

Page 2 of 12
2. Four Seven Segment Display:

Component Side:
Figure 4:​Soldered side of 4 digit seven segment display
Page 3 of 12
Figure 3: ​Component side of 4 digit seven

segment

Soldering Side:
3. Yellow Dot-Matrix:

Component Side:

Figure 5: ​Component Side of Yellow-Dot-Matrix

Soldering Side:
Figure 6: ​Soldered side of Yellow-Dot-Matrix.

Page 4 of 12
4. RGB Dot-Matrix:
Component Side:
Figure 7: ​Component side of RGB-Dot Matrix

Soldering Side:

Figure 8: ​Soldered side of RGB-Dot Matrix


Page 5 of 12
Print Circuit Board Projects

1. Four Seven Segment Display

Software:

Altium Design:
Figure 9:​PCB design of ​four seven segment
display

Bottom Layer Only:


Figure 10:​Bottom Layer of ​four seven segment display

Page 6 of 12
2. Yellow Dot Matrix
Software:
Altium Design:
Figure 13: ​Altium Design of Yellow Dot Matrix

Bottom Layer Only:


Figure 14: ​Bottom Layer of Yellow Dot Matrix

Page 7 of 12
3. RGB Dot Matrix
Software:
Altium Design:
Figure 15: ​Altium Design of RGB Dot Matrix

Bottom Layer Only:


Figure 16: ​Bottom Layer of RGB Dot Matrix.

Page 8 of 12
4. Yellow Dot-Matrix Surface Mount Device:
Software:
Altium Design:
Figure 17: ​PCB Design of Surface Mount Yellow Dot Matrix

Bottom Layer Only:

Figure 18:​Bottom Layer of Surface Mount Yellow Dot Matrix


Page 9 of 12
Figure 19: ​Soldering Side of SMD

Figure 20: ​Component Side of SMD

Make Your Own Arduino Nano(DIY-Arduino NANO)

1- Problem Statement
To make a microcontroller that is built up by the use of surface mount technology.

2- Theoretical Background

Basically the components used in this project are:

1. ATMEGA-32-08 is a 32 pin configuration IC which is used for the control for input and output
of appliances through it. 2. Capacitors of different capacitances. 3. Header
connectors for input and output. 4. Serial Programming header for the control of
application through the software. 5. Resistors for the serial programming header input
. 6. Push button switch and Crystal.

Page 10 of 12
Bottom Soldering Side: Top Component Side:
3- Procedure

In this project , following series of actions were taken for microcontroller:

● ​Different SMD components were placed .


● ​Then the netlist was defined according to the circuit diagram and the nets were set according to it for
each component
● ​Holes size were also adjusted for their practical use and headers
● ​Dimensions of project was also set equivalent to the international standards of arduino as it
is a nano arduino.

4- Results and Discussions


Discussion:

Dimension of this display is 45mm X 25mm .

It is just a microchip connected to specific instructions and guiding the appliance to follow its
instructions.

Arduino Nano ​Pinout contains 14 digital pins, 8 analog Pins, 2 Reset Pins & 6 Power Pins.
Each of these Digital & Analog Pins are assigned with multiple ​functions ​but their main
function ​is to be configured as input or output.

Page 11 of 12
In its practical use the original Arduino Nano look like this:
5-Conclusions

So the Arduino Nano is just a simple microcontroller which is used for the control of different

applications according to the user. ​Arduino ​boards are able to read inputs - light on a sensor, a

finger on a button, and turn it into an output - activating a motor, turning

on an LED, publishing something online.

Moreover , these microcontrollers vary over the science according to their size and usage type

.Like most of arduinos can control any intensity of light through their software input
Page 12 of 12

You might also like