Narrow-Aisle, Single & Double Reach, AC Powered Lift Trucks

N35-40ZRS/
N30ZDRS
2
The Hyster® Advantage

PRODUCTIVITY: DEPENDABILITY: ERGONOMICS:

• AC hoist system maximizes lift at lower speeds • CANbus communication system reduces • Drive-Rite Design Intent
• AC traction system maximizes performance wiring and electrical connections and • Configuration flexibility with fore/aft and side
and provides seamless direction transitions provides real time diagnostics stances available
• Electric power steering, standard on all models, • Sealed electrical connectors keep out debris • Large operator compartment and optimal
offers on-demand steering for maximum and help reduce the possibility of loose operator position allow easy entry and exit
efficiency and minimal battery drain connections without awkward twisting
• Automatic drive tire centering at start-up • O-ring face seal fittings help maximize uptime • Low 9.6” step height helps reduce operator
saves time for the operator and reduce leaks fatigue
• Automatic brake operation applies the brake • Completely brushless AC traction and hoist • Brake pedal location and design is optimized
when the truck is stationary, eliminating the motors improve reliability for operator comfort
need for the operator to lift a leg to apply the • Thermal management system for all motors • Optional suspended floorplate cushions the
brake and controllers add protection from overheating operator and helps reduce stress on the
• Optional electrically steered caster • Dedicated auxiliary pump and motor helps operator’s legs
reduce demand on main hydraulic motor • Adjustable steer tiller position
• Adjustable back with armrest
• On-demand electric power steering helps
reduce operator effort

SERVICEABILITY:
COST OF OPERATION: • Daily operator checks can be performed
• AC traction and hoist motors help reduce without removing covers
maintenance through a simpler design and • Full diagnostics are standard, easing VERSATILITY:
the elimination of brush replacement serviceability, helping reduce troubleshooting • Multiple battery compartments are available:
• Sealed load wheels bearings reduce greasing time and vehicle downtime – 12.5”, 14.5” and 16.5” for 3,500 and
requirements • Easy access to all components for regular 4,000 lb. models
• Brushless steering and auxiliary motors maintenance and repair – 14.5” and 16.5” for 3,000 lb. models
reduce maintenance time and cost • Completely brushless traction, hoist and • Four programmable vehicle modes are
• Electric brake provides parking and emergency auxiliary function motors help reduce service available for maximum speed, acceleration,
braking capability with no need to service time deceleration and hydraulic ramping
• Dual articulating caster wheels promote even • Regenerative braking helps reduce brake wear • Multi-function control handle integrated in
tire wear and minimize tire scrub • No need to remove the mast for adjustments armrest (side stance)
 Raising the Standard for Lift Trucks 3

Mast: Adjustable wear

strips help keep channel
rails properly aligned. Mast
removal and disassembly is
not required for adjustments.

On-Demand Electric Steering:

Low effort reduces operator fatigue.

Configuration Flexibility:
Provides optimal operator
positioning. Ability to select
different stances (Fore/Aft
or Side stance) and different
control handle configurations.

Trucks shown with optional equipment.

Low Step Height: The 9.6” step

height provides easy entry/exit to
reduce operator fatigue.
 4.6” 5.6”

DIMENSIONS
(117) (143)
24 5.0” (127) x 2.9” (74) 5.0” (127) x 3.9” (99)
4

Chassis
42.8"
(1087) 3.9”
(100)
30.0” (762)
14.2” (360)

O.H.G.
Width
42.1”
(1070)

5.6” 4.6”
(143) (117)
24
5.0” (127) x 3.9” (99) 5.0” (127) x 2.9” (74)


v

v


v

 






7IDTH!CROSS-AST#HANNELS
v v-AST
&ORE!FT3TANCE-ODEL 
v &IXED(T
3IDE3TANCE-ODEL v
,OWEREDv BATTERY
2AISEDv ROLLERHT

v 8v
v
 v v
v Xv
v
h 

v  v
 

Circled dimensions correspond to the line numbers on the tabulated chart inside the Technical Guide. Dimensions are in inches (millimeters).

N35-40ZRS
 N35-40ZRS SPECIFICATIONS 5

1 Manufacturer Name Hyster Company Hyster Company Hyster Company Hyster Company
2 Model N35ZRS N35ZRS N40ZRS N40ZRS
3 Wheel Base Designation SWB SWB SWB SWB
4 Rated Capacity lb. (kg) 3500 (1588) 3500 (1588) 4000 (1814) 4000 (1814)
GENERAL

5 Load Center, Distance in. (mm) 24 (610) 24 (610) 24 (610) 24 (610)

6 Power Type - Electric, Diesel, LPG Electric - 24 volt Electric - 36 volt Electric - 24 volt Electric - 36 volt
7 Operator Type Stand Stand Stand Stand
8 Tire Type - Load/Caster/Drive Poly / Poly / Rubber Poly / Poly / Rubber Poly / Poly / Rubber Poly / Poly / Rubber
9 Wheels, Number Load/Drive (x=driven) 4 / 2 (1x) 4 / 2 (1x) 4 / 2 (1x) 4 / 2 (1x)
10 Truck Weight, without Battery (approximate) lb. 4950 4950 5000 5000
WT.

11 Front Rear Front Rear Front Rear Front Rear

12 Axle Loading - Front/Rear with Carriage Extended ** lb. 6750 3800 6750 3800 7400 3700 7400 3700
13 Height, Standard Lift (TOF) in. (mm)
14 Height, Standard mast Lowered (OALH) in. (mm)
15 Height, Freelift (TOF) in. (mm)
See Mast Table See Mast Table See Mast Table See Mast Table
16 Height, Standard Mast Extended w/LBR in. (mm)
17 Height, Top of OHG in. (mm)
18 Height, Operator Clearance in. (mm)
19 Mast Tilt Angle, Forward/Back degrees° 3/4 3/4 3/4 3/4
DIMENSIONS

20 Forks, Standard (Length x Width x Thickness) in. 1.6 x 3.9 x 42 1.6 x 3.9 x 42 1.8 x 3.9 x 42 1.8 x 3.9 x 42
21 Headlength to Face of Forks - All Battery Compartments *** in. (mm) See Mast Table See Mast Table See Mast Table See Mast Table
22 Basearm OEC in. 34”- 49” (1” increments) 34”- 49” (1” increments) 34”- 49” (1” increments) 34”- 49” (1” increments)
23 Battery Compartment Size, 12.5” Battery Compartment - (LxWxH) in. 39.0 x 12.5 x 31.5 39.0 x 12.5 x 31.5 39.0 x 12.5 x 31.5 39.0 x 12.5 x 31.5
Battery Compartment Size, 14.5” Battery Compartment - (LxWxH) in. 39.0 x 14.5 x 31.5 39.0 x 14.5 x 31.5 39.0 x 14.5 x 31.5 39.0 x 14.5 x 31.5
Battery Compartment Size, 16.5” Battery Compartment - (LxWxH) in. 39.0 x 16.5 x 31.5 39.0 x 16.5 x 31.5 39.0 x 16.5 x 31.5 39.0 x 16.5 x 31.5
24 Turning Radius - minimum outside, 12.5” Battery Compartment in. 65.74 65.74 65.74 65.74
Turning Radius - minimum outside, 14.5” Battery Compartment in. 65.74 65.74 65.74 65.74
Turning Radius - minimum outside, 16.5” Battery Compartment in. 67.74 67.74 67.74 67.74
25 Aisle Width - Zero Clearance - Right Angle Stack see chart See “RAS” Table See “RAS” Table See “RAS” Table See “RAS” Table
26 Stability - Comply with ANSI Yes Yes Yes Yes
28 Travel Speed, Rearward (chasis first) - Empty/RL mph 6.5/6.5 6.7/6.5 6.5/6.5 6.7/6.5
29 Travel Speed, Forward (forks first) - Empty/RL mph 6.5/6.5 6.7/6.5 6.5/6.0 6.7/6.0
31 Lift Speeds, Empty ft./min 60 75 60 75
PERFORMANCE

32 Lift Speeds, 2,000 lb. ft./min 46 54 46 54

33 Lift Speeds, 3,000 lb. ft./min 43 50 43 50
34 Lift Speeds, 3,500 lb. ft./min 40 47 40 47
35 Lift Speeds, 4,000 lb. ft./min N/A N/A 38 45
36 Lift Speeds, 4,500 lb. ft./min N/A N/A N/A N/A
37 Lowering Speeds, Empty ft./min 85 85 85 85
38 Lowering Speeds, RL ft./min 85 85 85 85
39 Size - Front Load Wheels, Standard 5 x 3.9 5 x 3.9 5 x 3.9 5 x 3.9
40 Drive Caster Drive Caster Drive Caster Drive Caster
WHEELS & TIRES

41 Size, Standard - Drive Tire/Dual Casters 12.0 x 5.5 7.9 x 2.2 12.0 x 5.5 7.9 x 2.2 12.0 x 5.5 7.9 x 2.2 12.0 x 5.5 7.9 x 2.2
42 Wheelbase - 12.5” Battery Compartment in. 55.35 55.35 55.35 55.35
Wheelbase - 14.5” Battery Compartment in. 55.35 55.35 55.35 55.35
Wheelbase - 16.5” Battery Compartment in. 57.36 57.36 57.36 57.36
43 Brakes, Method of Control - Service/Parking Foot Foot Foot Foot
44 Brakes, Method of Operation - Service/Parking Spring Apply / Electric Release Spring Apply / Electric Release Spring Apply / Electric Release Spring Apply / Electric Release
45 Battery Type Lead Acid Lead Acid Lead Acid Lead Acid
46 Traction Motor Rating (60 minute rating) hp (kw) 7.5 (5.6) 7.5 (5.6) 7.5 (5.6) 7.5 (5.6)
ELECTRIC

47 Hoist Motor Rating (5 minute rating) hp (kw) 14.8 (11.0) 14.8 (11.0) 14.8 (11.0) 14.8 (11.0)
48 Traction Motor Control Method Transistor Transistor Transistor Transistor
49 Hoist Motor Control Method Transistor Transistor Transistor Transistor
50 Number of Speeds Infinitely Variable Infinitely Variable Infinitely Variable Infinitely Variable

SWB = Short Wheel Base

** Static with Rated Load and Max. Wt. Battery
*** Add 1” for Sideshift

CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time of
manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
NOTE: Performance specifications / ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and the proposed application should be discussed with your authorized Hyster Dealer.
6
DIMENSIONS

Chassis
42.8"
(1087) 3.9”
(100)
30.0” (762)
14.2” (360)

O.H.G.
Width
42.1”
(1070)

4.6” 5.6”
(117) (143)
24 5.0” (127) x 2.9” (74) 5.0” (127) x 3.9” (99)


v

v


Chassis
42.8"
(1087) 3.9” v
(100)
30.0” (762)
14.2” (360)

O.H.G.
Width  
42.1”
(1070)


5.6” 4.6”
(143) (117) 


24 7IDTH!CROSS-AST#HANNELS
5.0” (127) x 3.9” (99) v v-AST 5.0” (127) x 2.9” (74)

&ORE!FT3TANCE-ODEL
v &IXED(T 
3IDE3TANCE-ODEL v
,OWEREDv BATTERY
2AISEDv ROLLERHT

v Xv
v
 v v

v X v

h 

v  v
 

Circled dimensions correspond to the line numbers on the tabulated chart inside the Technical Guide. Dimensions are in inches (millimeters).

N30ZDRS
 N30ZDRS SPECIFICATIONS 7

1 Manufacturer Name Hyster Company Hyster Company

2 Model N30ZDRS N30ZDRS
3 Wheel Base Designation LWB LWB
4 Rated Capacity lb. (kg) 3000 (1361) 3000 (1361)
GENERAL

5 Load Center, Distance in. (mm) 24 (610) 24 (610)

6 Power Type - Electric, Diesel, LPG Electric - 24 volt Electric - 36 volt
7 Operator Type Stand Stand
8 Tire Type - Load/Caster/Drive Poly / Poly / Rubber Poly / Poly / Rubber
9 Wheels, Number Load/Drive (x=driven) 4 / 2 (1x) 4 / 2 (1x)
10 Truck Weight, without Battery (approximate) lb. 5250 5250
WT.

11 Front Rear Front Rear

12 Axle Loading - Front/Rear with Carriage Extended ** lb. 6300 4050 6300 4050
13 Height, Standard Lift (TOF) in. (mm)
14 Height, Standard mast Lowered (OALH) in. (mm)
15 Height, Freelift (TOF) in. (mm)
See Mast Table See Mast Table
16 Height, Standard Mast Extended w/LBR in. (mm)
17 Height, Top of OHG in. (mm)
18 Height, Operator Clearance in. (mm)
19 Mast Tilt Angle, Forward/Back degrees° 3/4 3/4
DIMENSIONS

20 Forks, Standard (Length x Width x Thickness) in. 1.6 x 3.9 x 42 1.6 x 3.9 x 42
21 Headlength to Face of Forks - All Battery Compartments *** in. (mm) See Mast Table See Mast Table
22 Basearm OEC in. 34”- 49” (1” increments) 34”- 49” (1” increments)
23 Battery Compartment Size, 12.5” Battery Compartment - (LxWxH) in. N/A N/A
Battery Compartment Size, 14.5” Battery Compartment - (LxWxH) in. 39.0 x 14.5 x 31.5 39.0 x 14.5 x 31.5
Battery Compartment Size, 16.5” Battery Compartment - (LxWxH) in. 39.0 x 16.5 x 31.5 39.0 x 16.5 x 31.5
24 Turning Radius - minimum outside, 12.5” Battery Compartment in. N/A N/A
Turning Radius - minimum outside, 14.5” Battery Compartment in. 70.74 70.74
Turning Radius - minimum outside, 16.5” Battery Compartment in. 72.74 72.74
25 Aisle Width - Zero Clearance - Right Angle Stack see chart See “RAS” Table See “RAS” Table
26 Stability - Comply with ANSI Yes Yes
28 Travel Speed, Rearward (chasis first) - Empty/RL mph 6.5/6.5 6.7/6.7
29 Travel Speed, Forward (forks first) - Empty/RL mph 6.5/6.5 6.7/6.7
31 Lift Speeds, Empty ft./min 60 75
PERFORMANCE

32 Lift Speeds, 2,000 lb. ft./min 44 51

33 Lift Speeds, 3,000 lb. ft./min 40 47
34 Lift Speeds, 3,500 lb. ft./min N/A N/A
35 Lift Speeds, 4,000 lb. ft./min N/A N/A
36 Lift Speeds, 4,500 lb. ft./min N/A N/A
37 Lowering Speeds, Empty ft./min 85 85
38 Lowering Speeds, RL ft./min 85 85
39 Size - Front Load Wheels, Standard 5 x 2.9 5 x 2.9
40 Drive Caster Drive Caster
WHEELS & TIRES

41 Size, Standard - Drive Tire/Dual Casters 12.0 x 5.5 7.9 x 2.2 12.0 x 5.5 7.9 x 2.2
42 Wheelbase - 12.5” Battery Compartment in. N/A N/A
Wheelbase - 14.5” Battery Compartment in. 60.35 60.35
Wheelbase - 16.5” Battery Compartment in. 62.36 62.36
43 Brakes, Method of Control - Service/Parking Foot Foot
44 Brakes, Method of Operation - Service/Parking Spring Apply / Electric Release Spring Apply / Electric Release
45 Battery Type Lead Acid Lead Acid
46 Traction Motor Rating (60 minute rating) hp (kw) 7.5 (5.6) 7.5 (5.6)
ELECTRIC

47 Hoist Motor Rating (5 minute rating) hp (kw) 14.8 (11.0) 14.8 (11.0)
48 Traction Motor Control Method Transistor Transistor
49 Hoist Motor Control Method Transistor Transistor
50 Number of Speeds Infinitely Variable Infinitely Variable

LWB = Long Wheel Base

** Static with Rated Load and Max. Wt. Battery

CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time of
manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck.
NOTE: Performance specifications / ratings are for truck equipped as described under Standard Equipment in this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it
is equipped, as well as by the nature and condition of the operating area. Specifications are subject to change and the proposed application should be discussed with your authorized Hyster Dealer.
8
MAST DIMENSIONS AND BATTERY SPECIFICATIONS

MAST DIMENSIONS (5.5” STANDARD DUTY)

Head Length
Overall Height Overhead (Length to Face of Forks)
Maximum Overall (Mast Extended) Guard
12.5”, 14.5” B.C. 16.5” B.C.
Fork Ht. Lowered Highest Point w/ 36” Free-Lift Height Operator
(TOF) Height Load Backrest (TOF) to Top Clearance Single Double Single Double
in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Reach Reach Reach Reach

3-STAGE FULL FREE-LIFT (FFL) VISTA® MAST

191 (4851) 87 (2210) 230 (5842) 48 (1219) 86.5 (2197) 75.3 (1913) 52.12 58.02 54.12 60.02
203 (5156) 91 (2311) 242 (6147) 52 (1321) 90.5 (2299) 79.3 (2014) 52.12 58.02 54.12 60.02
212 (5385) 95 (2413) 251 (6375) 56 (1422) 94.5 (2400) 83.3 (2116) 52.12 58.02 54.12 60.02
227 (5766) 101 (2565) 266 (6756) 62 (1575) 91 (2311) 79.8 (2027) 52.12 58.02 54.12 60.02
242 (6147) 107 (2718) 281 (7137) 68 (1727) 91 (2311) 79.8 (2027) 52.12 58.02 54.12 60.02
251 (6375) 110 (2794) 290 (7366) 71 (1803) 91 (2311) 79.8 (2027) 52.12 58.02 54.12 60.02
272 (6909) 119 (3023) 311 (7899) 80 (2032) 91 (2311) 79.8 (2027) 52.12 58.02 54.12 60.02

Right Angle Aisle Stacking

Note: These are “Zero Clearance” aisles and require an additional 6” or more to be added to provide for easier maneuvering.
LOAD WIDTH
N35/40ZRS
Truck with 12.5” or 14.5” Battery Compartment and 42” ID
3 Stage - 4” Between Loads
Pallet Width (inches)
36 40 44 48
Pallet 36 85 85 85 85 SPACING
LOAD
LENGTH
Length
(inches) 40 87 87 86 86
44 92 91 91 90
48 96 96 95 95
Add 2” for 16.5” Battery Compartment; Add 1” for Sideshift

N30ZDRS
Truck with 14.5” Battery Compartment and 42” ID
ZERO CLEARANCE
3 Stage - 4” Between Loads AISLE WIDTH
RIGHT ANGLE STACKING
Pallet Width (inches) AISLE LAYOUT
36 40 44 48
Pallet 36 90 90 90 90
Length
(inches) 40 91 91 91 91
44 95 94 94 93
48 99 99 98 98
Add 2” for 16.5” Battery Compartment; Sideshift is Standard on Double Reach

Battery and Compartment Specifications

X
Battery Specifications 406 TYP.
(16 in.)

Maximum Battery Dimensions Minimum Maximum

Battery 6 Hr Rate “X” Max. “Y” Max. “Z” Max. Batt. Wt. Batt. Wt.
Compartment Battery
Size Voltage AH KWH in. (mm) in. (mm) in. (mm) lb. (kg) lb. (kg)
Z
12.5” 24 1085 25.4 38.8 (985) 12.25 (311) 31.0 (788) 1400 (635) 1900 (862)
14.5” 24 1240 29.0 38.8 (985) 14.25 (362) 31.0 (788) 1600 (726) 2100 (953)
14.5” 36 775 27.2 38.8 (985) 14.25 (362) 31.0 (788) 1600 (726) 2100 (953)
16.5” 24 1395 32.6 38.8 (985) 16.25 (413) 31.0 (788) 1850 (839) 2350 (1066)
Y
16.5” 36 930 32.6 38.8 (985) 16.25 (413) 31.0 (788) 1850 (839) 2350 (1066)
Battery Compartment is designed to accommodate standard wet cell batteries with fixed lifting eyes and no cover.
Contact Applications Engineering to verify compatibility / fit when using maintenance free, covered or non-standard batteries.
Battery Connector: 24V - Red; 36V - Gray; Position “B”, Lead Length 16”
Manufacturers Standard Cable Size Not to Exceed 4/0 AWG
 Standard Features and Options 9

STANDARD EQUIPMENT optional equipment

• Fore/Aft Stance Operator Controls • Side Stance Operator Controls
• 24 Volt Battery (Includes 350 Amp Red Battery Connector) • Reverse Steering
• 91” / 203” / 52” – 3 Stage Full Free Lift Mast • Steered Caster - Electric
• Single Reach Mast (24” Extend) with 33.5” Wide Class II Hook • Keyless Start
Type Carriage (Standard on N35ZRS and N40ZRS) • Premium Display
• Double Reach Mast (42” Extend) with 33.5” Wide Class II Hook • 36 Volt Battery (Includes 350 Amp Gray Battery Connector)
Type Carriage (Standard on N30ZDRS) • Battery Stand
• Forks: 1.8” x 3.9” (45 mm x 100 mm) 42”(1067 mm) – Class II • Battery Puller
Hook Type (Standard on N40ZRS) • Cooler/Freezer Construction (0° F to 120° F)
• Forks: 1.6” x 3.9” (40 mm x 100 mm) 42” (1067 mm) – Class II • Various-Sized Load Wheels with Sealed Bearings
Hook Type (Standard on N30ZDRS and N35ZRS) • Tapered Basearm
• 5” x 3.9” Poly Articulating Tandem Load Wheels - High Load • Poly Siped Drive Tires
Compound (Standard on N35ZRS and N40ZRS) • Lift Limits
• 5” x 2.9” Poly Articulating Tandem Load Wheels - High Load • Various Fork Lengths
Compound (Standard on N35ZRS) • Fork Height Display
• Integral Sideshift for Standard 33.5” Wide Carriage- 7” Total • 48” High Load Backrest Extension
Sideshift Travel (Standard on N30ZDRS) • Audible Back-up and Motion Alarms
• AC Traction, Lift / Lower and Steering • Rear Operator Compartment Door
• Fully Integrated CANbus Controls • Audible Motion Alarm
• Low Step Height • Visual Amber Strobe Light
• Transistor Controller with Regenerative Braking • Operator Desktop Light
• Fully Proportional Lift/Lower Control • Dual Headlight
• Programmable Traction Speed and Acceleration • Rear Worklight
• Electric Power Steering • Operator Overhead Fan
• Automatic Field Control and Auto Deceleration • Load Weight Display
• Rubber Drive Tire - 12.0” x 5.5” • Reduced Travel Speed with Carriage Extended
• Dual Articulating Polyurethane Caster Wheels • RF Terminal Bracket
• Emergency Power Disconnect • RF Handheld Scanner Holder
• Battery Discharge Indicator with Lift Interrupt • Impact Monitor
• Key Start • Parts Manual
• 36” High Load Backrest Extension
• Sealed Battery Rollers
• Tilting Carriage (3° Fwd, 4° Back)
• Padded Operator Compartment
• Rear Post Operator Protection
• Operator’s Overhead Guard
• Low Profile Anti-Fatigue Floormat
• Operator’s Display with Alpha Numeric Messaging
• Multi-Mode Hour Meter
• Control Handle with Simultaneous Hydraulic Functions
• Electronic Horn
• Static Discharge Strap
• Operator’s Manual
• UL Classification E

N35-40ZRS/N30ZDRS
10
Standard Features and Options

CAPACITY: Rated capacities are for trucks equipped with:

Model N30ZDRS: 3,000 lbs. at 24.0” (1,361 kg at 610 mm) load center. • 3-Stage full free-lift (FFL) VISTA® mast to maximum fork height of 203” (5156 mm)
Model N35ZRS: 3,500 lbs. at 24.0” (1,588 kg at 610 mm) load center. • 33.5” (851 mm) wide hook-type carriage, single reach (24.0” extend) with 42.0” (1067 mm) long forks
Model N40ZRS: 4,000 lbs. at 24.0” (1,814 kg at 610 mm) load center. • 33.5” (851 mm) wide hook-type carriage, double reach (42.0” extend) with 42.0” (1067 mm) long forks
• 36.0” high load backrest extension (LBE)
• 1.8” x 3.9” (45 mm x 100 mm) 42” (1067 mm) long forks [N40ZRS]
• 1.6” x 3.9” (40 mm x 100 mm) 42” (1067 mm) long forks [N35ZRS and N30ZDRS]
• 5” x 3.9” poly articulating tandem load wheels [N35ZRS and N40ZRS]
• 5” x 2.9” poly articulating tandem load wheels [N30ZDRS]

Masts The Fore/Aft stance multi-function handle utilizes a single pivot Four operator selectable drive modes are available: rabbit, battery
Models are equipped with a 5.5” 3-stage FFL mast assembly. axis for traction control, and thumb actuated controls for lift/lower saver, mid, and turtle. Rabbit mode provides maximum acceleration
The mast is constructed with the nested channel VISTA® design with operation. The handle provides simultaneous operation of traction, and travel speeds. The battery saver mode provides high travel
full-face, straight load rollers. Brass side thrust plugs allow easy lift/lower, and reach functions. Additionally, the handle is utilized in speeds at reduced acceleration. Mid mode reduces travel speeds and
mast adjustment during periodic maintenance without removal or rearward travel and provides traction and horn operation. acceleration further. Turtle mode reduces travel speed by 50% and
disassembly of mast. The Side stance multi-function control handle assembly offers also limits acceleration.
palm rest and large function buttons. The handle allows simultaneous
Carriage operation of traction, lift/lower, and one auxiliary function. Brake
The single reach mechanisms provide 24 inches of extension. A spring applied, electrically released brake is standard on all
The double reach mechanisms provide 42 inches of extension. Tilt Steering System models.
function provides 4 degrees back tilt and 3 degrees forward tilt on both Electric on-demand power steering The brake is pre-adjusted and requires no servicing. Regenerative
carriages. Sideshift is optional on single reach mechanisms. Double Auto-centering at start-up braking is standard. When the motor RPM reaches 200, the brake is
reach mechanism is offered with sideshift feature. Integral sideshift Adjustable lock to lock activated.
allows seven total inches of sideshift and is reduced to 3 inches total Adjustable tiller force feedback The brake pedal mounting location is optimized for each stance
with OEC less than 39 inches. Speed sensitive power assist allowing comfortable operation by a wide range of operators. The
The pantograph (reach mechanism) arms are all made from Electronic adjustment of steer modes for automotive or reverse switch mounting locations require the operator to be within the
one-inch thick alloy steel. The inner arm weldments have additional steering operator compartment in normal operator position prior to enabling
gusset plates for added strength and rigidity. The main pantograph operation of vehicle traction and hoist systems.
pivots use tapered roller bearings which provide a stiffer pivot joint. Battery
The reach mechanism hoses and wires are installed in a plastic cable The steel battery compartment provides secure storage and
carrier. The cable carrier secures wires and hose inside and provides Operator Compartment
provides battery access / service from either side of the truck.
positive routing for both. Sealed connectors are used throughout the Two operator compartments are offered, Fore/Aft stance and
Equipped with corrosion resistant, ball bearing battery rollers, Side stance. The operator’s Drive Rite Design Intent compartment is
mechanism.
battery installation or removal is a quick and easy process. ergonomically designed to provide operators with excellent visibility,
efficiency and productivity.
Forks
Hydraulic System Operator controls are positioned for optimum productivity and
All fork assemblies are all hook type forks.
The AC hydraulic system features proportional lifting and lowering. comfort on both Fore/Aft stance and Side stance with standard
N35ZRS and N40ZRS
The lift function is controlled by varying lift motor RPM, which adjustable steer tiller.
1.8”x 3.9” x 36”, 42”, 48”
maximizes system efficiency. By utilizing the lift motor RPM to control Low 9.6 inch step height, combined with a wide entrance opening
(45 mm x 100 mm x 914 mm, 1067 mm, or 1219 mm)
oil flow, pressure drop in the lift hydraulic lines is minimized. The lower into the operator compartment, provides comfortable entry and exit
function is controlled by a proportional control valve which provides from the truck.
N30ZDRS
excellent lowering speed control.
1.6” x 3.9” x 36”, 42”, 48” Compartments have room for the operator to vary their stances
(40 mm x 100 mm x 914 mm, 1067 mm, or 1219 mm) The lift motors are highly reliable AC designs featuring a Class F and include a floating floor plate design with an ergonomically shaped
insulation rating. The motors have speed and temperature sensors floor mat for excellent ride comfort and reduced body fatigue.
mounted internally. The temperature sensor protects the motor from
Electrical System Both the brake and operator sensing switch are mounted below the
overheating. The speed sensor provides feedback to the hoist controller
The state-of-the-art electrical system features a CANbus floor mat, providing unobstructed entry and exit from the truck.
for precise speed control.
communication network linking all vehicle systems. The Vehicle Operator compartments are fully padded for comfort and as a
System Manager is an electronic module with an integral thermal insulator from drive compartment heat.
microprocessor that controls input and output capabilities. The Drive Train
The Side stance compartment provides a large backrest pad with
vehicle application software monitors operator inputs and vehicle The AC traction system offers excellent acceleration, deceleration
integral lumbar and armrest support with optional vertical adjustment
performance. The software adjusts vehicle performance as needed to or regenerative braking and seamless, smooth transitions during
for a wide range of operator heights.
improve the operation of the truck. plugging.
Doors are intended to protect the operator from objects that
Hand controls, which are positioned to optimize each stance The plugging function is variable according to the handle position.
may enter the operator’s compartment but they may also slow the
configuration, include the multi-function handle, steer tiller assembly, All deceleration is performed by regenerative braking through the
operator’s egress in emergency situations. A review of the forklift’s
dash display, key switch and emergency stop switch. vehicle control system. Regenerative braking puts vehicle kinetic
intended environment should be conducted before selecting a door as
energy back into battery, improving efficiency, and reducing wear on
optional equipment.
brake components.
 11

It’s not just about the lift trucks. Hyster Capital

Any company worth its weight knows success We know that financing new additions to your
FLEET SERVICES has just as much to do with the support before fleet can sometimes be challenging. That’s
and after the sale as the sale itself. We pride why your Hyster Dealer has a long list of ways
ourselves on being more than just a lift truck for you to fund your purchase. We are skilled
manufacturer. Through our Dealer Network, in arranging solutions for special financing
we’re also fleet managers, parts suppliers, requirements, taking the difficulties out of buying
capital procurement specialists and trainers. the equipment you need. Whether you purchase
You’ll find that when it comes to service, we or lease a new or used lift truck, Hyster Capital
do it all. offers better service and competitive rates,
ensuring you receive the value you deserve.
Hyster Fleet Services
As much as we’d like for your entire fleet to be Special Products
Hyster, we know that’s not always the case. Engineering Department (SPED)
But just because you also operate other brands In a perfect world, every application could be
HYSTER CAPITAL
A Division of NMHG Financial Services, Inc. doesn’t mean we can’t manage your lift truck handled with a standard lift truck. However,
maintenance and replacement plan. We can in the real world, different materials require
analyze your current fleet or provide summary different handling. That’s why Hyster Company’s
of your fleet history and a cost-effective proposal Special Products Engineering Department works
for replacement and scheduled maintenance with you to customize* your lift trucks. From
of all your vehicles. Once this initial review is strobe lights to specially made forks, SPED can
complete, we’ll continue to monitor your fleet to provide you with the tools you require to get the
ensure it’s performing optimally. job done right.
* May be subject to an additional charge. Contact your local
authorized Hyster Dealer for more information.
UNISOURCE™ Parts Program
In addition to providing fleet management for
a variety of brands, we can also serve as your Automated Warehouse Solutions
source of parts for all your lift trucks. With As society’s technological capabilities advance,
the Hyster UNISOURCE parts and service we strive to find practical applications. One
program, we offer approximately 2 million part of our most recent innovations in that pursuit
number crosses for most brands of materials is our development of automated warehouse
handling and other in-plant mobile equipment. solutions. We can help you determine if your
UNISOURCE also has remanufactured parts that operation would benefit from this type of system,
provide the same quality and guarantee but at which improves inventory accuracy, warehouse
a lower price. And we can deliver parts to you in productivity and safety records, as it reduces
less than 24 hours, any day of the week. How’s maintenance and overtime.
that for convenience?
Operator and Service Training
Rental Products Hyster Company recognizes that proper training
At Hyster Company, we’re always looking for is a key element of a profitable company. That’s
ways to help you keep your productivity up. why your local authorized Hyster Dealer offers
Through the Hyster Dealer Network, you can a training program for your lift truck operators
access rental equipment for the times when as well as those who maintain your vehicles.
leasing or buying isn’t a practical option. Your Proper education in running and servicing lift
local Hyster Dealer has access to over 14,000 trucks cuts down on the number of repairs and
units that are available for short- or long-term risk of injuries due to accidents while increasing
rental. Whether you need one truck to substitute productivity. All of our trainers are professionals
for a vehicle that’s being serviced or several lift with experience in materials handling.
trucks to accommodate seasonal changes in
your business, we’ll help you maintain output in
a cost-effective manner.
Hyster Company
Visit us online at www.hysteramericas.com
P.O. Box 7006 or call us at 1-800-HYSTER-1.
Greenville, North Carolina is a registered trademark of Hyster Company. Hyster and are trademarks of Hyster
27835-7006 Company. Hyster products are subject to change without notice.
Part No. N35-40ZRS/N30ZDRS Truck on cover shown with optional equipment.
BTG 7/2007 Litho in U.S.A. ©2006 Hyster Company. All rights reserved.