2 Pon Gepon Olt Maunal
2 Pon Gepon Olt Maunal
2 Pon Gepon Olt Maunal
1. HARDWARE INSTALLATION
This section describes the hardware features and installation of the GEPON OLT on the desktop or rack mount. For easier
management and control of the GEPON OLT, familiarize yourself with its display indicators, and ports. Front panel illustrations in
this chapter display the unit LED indicators. Before connecting any network device to the GEPON OLT, please read this chapter
completely.
The unit front panel provides a simple interface monitoring the OLT. Figure 1-1 shows the front panel of the GEPON OLT.
2 PON OLT Front Panel
■ Reset Button
The reset button is designed for rebooting the GEPON OLT without turning off and on the power. The following is the
summary table of reset button functions:
■ Management Port
10/100BASE-TX Copper, RJ45 Twist-Pair: Up to 100 meters
1000BASE-SX/LX mini-GBIC slot, SFP (Small Form Factor Pluggable) transceiver module: From 550 meters (multi-mode
fiber), up to 10/30/50/70/120 kilometers (single-mode f iber).
GE1 & GE2 Gigabit SFP uplink slots support 1000Mbps Forced Mode only. The remote
10
10
Gigabit switch or Media Converter’s SFP Port must support 1000Mbps Forced Mode as well.
11
11
■ Gigabit SFP PON Slots
1000BASE-PX20 mini-GBIC slot, SFP (Small Form Factor Pluggable) transceiver module: up to 20 kilometers
(single-mode f iber).
The front panel LEDs indicate instant status of port links, data activity and system power and help to monitor and troubleshoot
when needed. Figure 1-2 shows the LED indications of these GEPON OLTs.
■ System
L Color Functi
E on
PW R Green Lights: To indicate that the Switch is powered on.
Color
LED Function
Lights: To indicate the link through that SFP port is successfully established.
LINK Green
OFF: To indicate that the SFP port is link-down.
Green Blink: To indicate that the switch is actively sending or receiving data over that
ACT port.
Color
LED Function
Lights: To indicate the link through that PON port is successfully established.
LINK Green
Off: To indicate that the PON port is link-down.
12
12
1.1.3 OLT Rear Panel
The rear panel of the GEPON OLT indicates an AC inlet power socket, which accepts input power from 100 to 250V AC,
50-60Hz. Figure 1-3 shows the rear panel of this GEPON OLT.
■ AC Power Receptacle
For compatibility with electric service in most areas of the world, the GEPON OLT’s power supply automatically adjusts to
line power in the range of 100-250V AC and 50/60 Hz.
Plug the female end of the power cord firmly into the receptable on the rear panel of the GEPON OLT. Plug the other end of
the power cord into an electric service outlet then the power will be ready.
There is a power switch for AC power input use only, whereas DC power input has no power switch.
The device is a power-required device; if your networks should be active all the time, please
consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from
In some area, installing a surge suppression device may also help to protect your GEPON OLT
from being damaged by unregulated surge or current to the switch or the power adapter.
To install the GEPON OLT in a 19-inch standard rack, please follow the instructions described below:
Step 1: Place the GEPON OLT on a hard flat surface, with the front panel positioned towards the front side.
Step 2: Attach the rack-mount bracket to each side of the GEPON OLT with supplied screws attached to the package.
Figure 1-4 shows how to attach brackets to one side of the GEPON OLT.
13
13
Figure 1-4 Attaching Brackets to the GEPON OLT.
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate the warranty.
14
14
1.2.2 Installing the SFP Transceiver
The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and
hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the GEPON OLT as
■ GLA-TL70 SFP (1000BASE-SX SFP transceiver / Signle mode / 1310nm / 70km; -40~75℃)
GEPON OLT SFP ports of GE1 and GE2 are configured in 1000Mbps Forced
Mode. If want to make the connection successfully, the switch’s SFP ports should also be in
Before connecting the other GEPON OLT, workstation or Media Convert er,
15
15
1. Make sure both sides of the SFP transceiver are with the same media type, for example: 1000BASE-SX to 1000BASE-SX,
1000Bas-LX to 1000BASE-LX.
2. Check whether the fiber-optic cable type matches the SFP transceiver model.
To connect to 1000BASE-SX SFP transceiver, use the multi-mode fiber cable, with one side being male duplex LC
connector type.
To connect to 1000BASE-LX SFP transceiver, use the single-mode fiber cable, with one side being male duplex LC
connector type.
Never pull out the module without pulling the handle or the push bolts on the module. Directly
pulling out the module with force could damage the module and SFP module slot of the
GEPON OLT.
16
16
2. MANAGEMENT SOFTWARE INSTALLATION
This chapter explains the methods that you can use to configure management access to the GEPON OLT. It describes the types
of management applications and the communication and management protocols that deliver data between your management
device (workstation or personal computer) and the system. It also contains information about port connection opt ions.
Requirements
Management Access Overview
MySQL Installat ion
EMS Utility Installation
SNMP Access
2.1 Requirements
The GEPON OLT provides a GUI utility to manage the system; the following equipment is necessary for further management.
17
17
2.2 Management Access Overview
The GEPON OLT 2 PON OLT supports 10/100Mbps Management interface and two 1000BASE-X net interfaces f or
TCP/IP-based GUI Management. The GEPON OLT gives you the flexibility to access and manage it by using any or all of the
following methods:
EMS (Element Management System) Utility
An external SNMP-based network management application
Each of these management methods has their own advantages. Table 3-1 compares the two management methods.
18
18
2.3.1 MySQL Server Installation
3. When the Setup Type window appears, choose the default “Typical” mode. Please click “Next” butt on.
19
19
4. When the Ready to Install the Program window appears, please click “Install” button.
5. When the installation is done, the MySQL Enterprise window appears. Please click “Next” button.
20
20
6. The “W izard Completed” window appears, and it will ask for Configure the MySQL server and Register the MySQL
Server now. Please click “Finish” button.
7. The MySQL Server Instance Configuration Wizard window appears; please click “Next” bu tton.
20
20
8. The MySQL Server Instance Configuration window appears; keep the default setting of “Detailed Configuration”
and click “Next” button.
9. Please select a Server type. Keep the default setting of “Developer Machine” and click “Next” button.
21
21
10. Please select the database usage. Keep the default setting of “Multifunctional Database” and click “Next” butt on.
11. Choose where you want to place the InnoDB Datafile. Here is the remaining default setting. Please click “Next” button.
22
22
12. Please set the approximate number of concurrent connections. Keep the default setting of “Decision Support
(DSS)/OLAP“ and click “Next” bu tton.
13. Please set the Network options and Server SQL mode. Keep the default setting and click “Next” button.
23
23
14. Please select the default character set. Keep the default setting of “Standard Character Set” and click “Next” button.
15. Please set the W indows options. Keep default setting and click “Next” button.
24
24
16. Please set the security options. Type the password “1234” for current root and new root. Click “Next” button.
17. Please click “Execute” button for starting the conf iguration .
25
25
18. Please give a check to “Configuration file created”, “W indows service MySQL installed”, “Service started successfully”
and
“Security applied”, and then click “Finish” butt on .
26
26
3.3.2 EMS Utility Installation
1. Insert the bundled CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome
menu screen will appear. Click the “EMS” hyperlink, the InstallShield W izard dialog box will appear below.
2. Once the Setup program starts running, please click “Next” button for starting installation.
3. During the installation, it will ask for the place to put the EMS f older.
27
27
4. Click “Install” for starting
installation.
28
28
6. When the EMS is done, two icons -- Server and Client – will appear on the desktop.
The following shows how to start-up the EMS Management on the management PC.
1. Double-click the Server icon on the PC desktop. After a couple of seconds, it will appear on the lower-right corner of
the system t ray.
2. Double-click the Client icon on the PC desktop. It will pop-up a window to enter the user name and password. Please
enter the default user name "admin" and password “admin”. The login screen in Figure 2-24 appears.
29
29
3. After entering the user name and password, the EMS main screen will appear as in Figure 2-25.
30
30
3. EMS Management System
GEPON solutions include the OLT 2 PON OLT and ONUs. The following inf ormation introduces the software conf iguration.
This document explains how to use the EMS Utility for the purpose of evaluating the functionality and usability of Host Interf ace
Protocol. This manual assumes that the reader has a technical background and a base level of understanding regarding the
basic operation of PON equipment. The EMS Utility is a demonstration package, intended for evaluation purposes only.
The upper left panel displays the entities that may be managed by the Host Interface, including the OLT, ONUs and
Logical Links. This sash window will be referred to as the Element Status Window.
Left clicking on an entity with the mouse will open a tabbed panel in the upper right sash window that may be used t o
manage the entity. This sash window will be referred to as the Entity Management Window.
The bottom sash window is used for the purpose of logging the host interface message that is sent and received by the
EMS Utility, and will be referred to as the Message Log.
If the OLT is running normally and the ONUs register each of their LLIDs, you should see something similar to the figure. The left
handed pane shows the MAC addresses of the OLT and the ONU’s LLIDs. Depending on the number of ONUs, LLIDs, MAC
addresses, etc., you may see something slightly different. If the GUI fails to connect to the OLT, check the IP addresses of the
Host PC and the management port. Make sure you can ping the IP address assigned to the management port or uplink port. Also
verify that the Host and management IP addresses match in the GUI’s Utilities.
31
31
3.1 EMS Toolbar
The toolbar includes System, Alarm, Config, Performance and Help features which allows users to do advanced setting.
3.1.1 System:
It includes System Config, Mib Browser, Database Mainteance, User Manage and Exit.
Langua ge: Allows user to select the language: English and Simplified Chinese.
Enter the IP address which allows user to remote control from other PC with
IP: same IP subnet address. The default IP is 127.0 .0.1.
Port: Enter the UDP port number. The default port is 8888.
A built-in trap receiver can receive SNMP traps and handle trap st orm.
33
33
3.1.1.3 Database Maintenance
34
34
The popup window includes the following f ields:
Delete Account
:
: Save Account
3.1.1.5 Exit
Exit the Element Management System
3.1.2 Alarm:
It includes Alarm Query, Config Trap Rule, System Log and Trap W indow.
35
35
3.1.2.1 Alarm Query
The OLT alarms manager works in concert with the ONUs to provide enhanced management capabilities and complementary
set of OLT specific alarms.
Page Record Counts: Allows user to edit the number of events for per page.
36
36
3.1.2.2 Config Trap Rule
37
37
3.1.2.3 System Log
The GEPON EMS system log information is provided here. This window allows you to log the messages happened in this
system for later ref erence.
Page Record: Allows user to edit the number of logs for each page.
38
38
3.1.3 Config
This feature allows user to configure the Top Tree, 2 PON OLT, PON Card and ONU propert y.
Modify: Allows user to modify the property of Devices like: 2 PON OLT and PON Card.
39
39
3.1.4 Performance
This performance function helps user to verify the OLT connection. This window allows user to issue ICMP PING packets to
troubleshoot IP connectivity issues.
Once you select the target OLT in the Top Tree and click Performance\Ping from the Toolbar, ICMP packets are transmitted. The
report windows pop up automatically until responses to all packets are received, or until a timeout occurs. The Ping screen in
Figure 3-13 appears.
Be sure the target OLT’s IP Address is within the same network subnet of the EMS workstation, or
you have to set up the correct gateway IP address.
3.1.5 Help
Allows user to change the color of window and language.
40
40
Figure 3-15 Language Screen
Lauange: Allows user to choose two kinds of languages: English and Simplified Chinese.
41
41
3.2 OLT Management
To manage 2 PON OLT, EMS manager needs to add 2 PON OLT device. They can add and manage the 2 PON OLT from the
two types of interf aces:
Right-click Top Tree and then click [AddDevice] in the interface as the windows appear below.
42
42
For example, add M-E8221 through Management Port c onnection
Please enter the M-E8221 default IP address “192.168.1.10”, Read Community “public” and Write Community “private” of
the management port.
Double-click the 2 PON OLT device node unit in the topology tree, and click Chassis Management in the interface as the window
appears below:
43
43
Figure 3-20 2 PON OLT OLT Management
Screen
System Location: Allows user to fill in the words for system locat ion
System Description: Allows user to fill in the words for system description
System C ontact: Allows user to fill in the words for system con tact
44
44
3.2.2 Basic Information
The Basic System Info page provides information for the current device information. Basic System Info page helps an OLT
administrator to identify the firmware / hardware version, System Config and Switch Mode Conf igure.
Card Type: The OLT device type, 2 PON OLT is epon-olt type.
Running Ti me: The period of time the device has been operat ional.
Console Port Speed: The baud rate of Console Port. (Only for Manufacturer)
Read Comm unity: Indicates the community read access string to permit access to SNMP agent.
R/W Community: Indicates the community write access string to permit access to SNMP agent.
45
45
3.2.3 Net Interface Management
The system supports two Management IP ports: One is in-band IP and one is out-band IP ports. This page is allow you to
modify the in-band IP
Inband Manage ena ble: Allows user to manage 2 PON OLT through GE1 and GE2 port.
46
46
3.2.4 User Manage
This Page provides an overview of the current users. Currently the only way to login as another user on the web server is to
close and reopen the browser. Please press “Add” button for adding new login user account, after setup is completed, press
“OK” button to take effect. Please login web interface with new user name and password, the screen in Figure 3-24 appears.
User Passwor d: The password of the user. The allowed string length is 1 to 32.
Premission: The level of the user. There are three levels: guest, user and admin.
The login time for the user, when idle and over the setting time, it will login out
Login Timeout: aut omatically.
Buttons
47
47
Figure 3-25 User Manage Screen
User Passwor d: The password of the user. The allowed string length is 1 to 32.
Premission: The level of the user. There are three levels: guest, user and admin.
The login time for the user, when idle and over the setting time, it will login out
Login Timeout: aut omatically.
3.2.5 IGMPSetting
48
48
The window includes the following f ields:
Robust ness: Allows user to modify the Robusness, the range is 1 to 10.
Queryinterval : Allows user to modify the Query interval, the range is 100 to 200.
Queryres ponselnterval : Allows user to modify the Query respon interval, the range is 10 to 20.
Lastmem berqueryinterval Allows user to modify the last member query interval, the range is 10 to 20 .
:
Lastmem berquerycount: Allows user to modify the last member query count, the range is 1 to 5.
Trunk Management optimizes port usage by linking 2 GE ports together to form a single Link Aggregated Groups (LAGs).
Trunk multiplies the bandwidth between the devices, increases port flexibility, and provides link redundancy.
As GEPON OLT 2 PON OLT SFP Ports of GE1 and GE2 is configured in 1000Mbps Forced Mode,
the switch’s SFP Ports should also change to the same mode if the connection is to be established
successfully. Otherwise, the connection might f ail.
49
49
Figure 3-27 Trunk Management Screen
The window includes the following f ields:
A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical
layout. VLAN can be used to combine any collection of LAN segments into an autonomous user group that appears as a single
LAN. VLAN also logically segments the network into different broadcast domains so that packets are forwarded only bet ween
ports within the VLAN. Typically, a VLAN corresponds to a particular subnet, although not necessarily. VLAN can enhance
performance by conserving bandwidth, and improve security by limiting traffic to specific domains.
IEEE 802.1Q (tagged) VLAN are implemented on the Switch. 802.1Q VLAN requires tagging, which enables them to span the
entire network (assuming all switches on the network are IEEE 802.1Q-compliant).
VLAN allows a network to be segmented in order to reduce the size of broadcast domains. All packets entering a VLAN will only
be forwarded to the stations (over IEEE 802.1Q enabled switches) that are members of that VLAN, and this includes broadcast,
multicast and unicast packets from unknown sources.
VLAN can also provide a level of security to your network. IEEE 802.1Q VLAN will only deliver packets between stations that are
members of the VLAN. Any port can be configured as either tagging or unta gging.:
The untagging feature of IEEE 802.1Q VLAN allows VLAN to work with legacy switches that don't recognize VLAN tags
50
50
in packet headers.
The tagging feature allows VLAN to span multiple 802.1Q-compliant switches through a single physical connection and
allows Spanning Tree to be enabled on all ports and work normally.
The figure below shows the 802.1Q VLAN tag. There are four additional octets inserted after the source MAC address. Their
presence is indicated by a value of 0x8100 in the Ether Type field. When a packet's Ether Type field is equal to 0x8100, the
packet carries the IEEE 802.1Q/802.1p tag. The tag is contained in the following two octets and consists of 3 bits of user priority,
1 bit of Canonical Format Identifier (CFI - used for encapsulating Token Ring packets so they can be carried across Ethernet
backbones), and 12 bits of VLAN ID (VID). The 3 bits of user priority are used by 802.1p. The VID is the VLAN identifier and is
used by the 802.1Q standard. Because the VID is 12 bits long, 4094 unique VLAN can be identif ied.
The tag is inserted into the packet header making the entire packet longer by 4 octets. All of the information originally con tained in
the packet is retained.
802.1Q Tag
User CFI VLAN ID (VID)
Priority
3 1 12 bits
bit bits
s
2 bytes 2 bytes
The Ether Type and VLAN ID are inserted after the MAC source address, but before the original Ether Type/Length or Logical
Link Control. Because the packet is now a bit longer than it was originally, the Cyclic Redundancy Check (CRC) must be
recalculated.
Dest. Src. E. Ta Length/E. type Dat New CRC New Tagged Packet
Addr. Addr. type g a
51
51
■ Port VLAN ID
Packets that are tagged (are carrying the 802.1Q VID information) can be transmitted from one 802.1Q compliant network
device to another with the VLAN information intact. This allows 802.1Q VLAN to span network devices (and indeed, the entire
network – if all network devices are 802.1Q compliant).
Every physical port on a switch has a PVID. 802.1Q ports are also assigned a PVID, for use within the switch. If no VLAN are
defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1. Untagged packets are assigned the
PVID of the port on which they were received. Forwarding decisions are based upon this PVID, in so far as VLAN are concerned.
Tagged packets are forwarded according to the VID contained within the tag. Tagged packets are also assigned a PVID, but the
PVID is not used to make packet forwarding decisions, the VID is.
Tag-aware switches must keep a table to relate PVID within the switch to VID on the network. The switch will compare the VID of a
packet to be transmitted to the VID of the port that is to transmit the packet. If the two VID are different the switch will drop the
packet. Because of the existence of the PVID for untagged packets and the VID for tagged packets, tag-aware and tag-unaware
network devices can coexist on the same network.
A switch port can have only one PVID, but can have as many VID as the switch has memory in its VLAN table to store them.
Because some devices on a network may be tag-unaware, a decision must be made at each port on a tag-aware device bef ore
packets are transmitted – should the packet to be transmitted have a tag or not? If the transmitting port is connected to a
tag-unaware device, the packet should be untagged. If the transmitting port is connected to a tag-aware device, the packet
should be tagged.
■ Default VLANs
The Switch initially configures one VLAN, VID = 1, called "default." The factory default setting assigns all ports on the Switch t o
the "default". As new VLAN are configured in Port-based mode, their respective member ports are removed from the "def ault."
Before enabling VLANs for the switch, you must first assign each port to the VLAN group(s) in which it will participate. By def ault
all ports are assigned to VLAN 1 as untagged ports. Add a port as a tagged port if you want it to carry traffic for one or more
VLANs, and any intermediate network devices or the host at the other end of the connection supports VLANs. Then assign ports
on the other VLAN-aware network devices along the path that will carry this traffic to the same VLAN(s), either manually or
dynamically using GVRP. However, if you want a port on this switch to participate in one or more VLANs, but none of the
intermediate network devices nor the host at the other end of the connection supports VLANs, then you should add this port t o
the VLAN as an untagged port.
52
52
Tagged: Ports with tagging enabled will put the VID number, priority and other VLAN information
into the header of all packets that flow into those ports. If a packet has previously been tagged,
the port will not alter the packet, thus keeping the VLAN information intact. The VLAN
information in the tag can then be used by other 802.1Q compliant devices on the network to
make
packet-forwarding decisions.
Untagged: Ports with untagging enabled will strip the 802.1Q tag from all packets that flow into those
ports. If the packet doesn't have an 802.1Q VLAN tag, the port will not alter the packet. Thus,
all packets received by and forwarded by an untagging port will have no 802.1Q VLAN
information. (Remember that the PVID is only used internally within the Switch). Untagging is
used to send packets from an 802.1Q-compliant network device to a non-compliant network
device.
Frame Income
Income Frame is ta gged Income Frame is untagged
Frame Leave
To completely configure the VLAN functions on the GEOPN OLT, two of the following sub-menus are needed to be well
conf igured.
OLT Management \ VLAN
Manageme nt
OLT Management \ Port \ Port Property
53
53
Figure 3-28 VLAN Management Screen
Select specific port for this check box to transmit outgoing frames without
Untagged Port:
VL AN-Tagged.
54
54
Figure 3-29 Port Property Screen
Port ID: This is the logical port name for this row.
Allows to assign PVID for selected port. The range for the PVID is 1-4094.
The PVID will be inserted into all untagged frames entering the ingress port.
Port VID: The PVID must be the same as the VLAN ID whose port belongs to VLAN
group, or the untagged traffic will be dropped.
Allows user to modify the VLAN mode, there are two modes:
swPortvla nmode: Vlan-access: Only allow Untagged f rames
Vlan-Trunk: Allows Tagged and Untagged frames.
Enable ingress filtering for a port by checking the box. This parameter aff ects
VLAN ingress processing. If ingress filtering is enabled and the ingress port is
not a member of the classified VLAN of the frame, the frame is discarded.
Ingress Filter:
Ena bled
Disabled
By default, ingress filtering is disabled (no checkmark).
Determines whether the port accepts all frames or only VLAN tagged f rames.
This parameter affects VLAN ingress processing. If the port only accepts
tagged frames, untagged frames received on the port are discarded.
Permit Frame Type: Options:
allType
tagge d
By default, the field is set to allType.
55
55
3.2.8 IPTV Profile
Refresh: Refresh the Page. Any changes made locally will be undone.
This page allows for selecting the specific IPTV profile and creates their own IPTV channels.
56
56
Figure 3-31 IPTV Channel Screen
The user can select specific IPTV Profile; the IPTV profile is creating by IPTV
IPTV Profile:
profile page.
User View Time: Configures the time for viewing IPTV channel.
In Port Property you can configure the settings of each port to control the connection parameters, and the status of each port is
listed below:
57
57
Figure 3-32 Port Property Screen
Port ID: This is the logical port name for this row.
Mode Config: That is only one speed 1000Mbps for SFP transceivers.
Whether or not the receiving node sends feedback to the sending node is
determined by this item. W hen enabled, once the device exceeds the input
Flow Control Config: dat a rate of another device, the receiving device will send a PAUSE frame
which halts the transmission of the sender for a specified period of t ime.
When disabled, the receiving device will drop the packet if too much to process.
Allows to assign PVID for selected port. The range for the PVID is 1-4094.
The PVID will be inserted into all untagged frames entering the ingress port.
Port VID: The PVID must be the same as the VLAN ID whose port belongs to VLAN
group, or the untagged traffic will be dropped.
Allows user to modify the VLAN mode, there are two modes:
swPortvla nmode: Vlan-access: Only allow Untagged f rames
Vlan-Trunk: Allows Tagged and Untagged frames.
Enable ingress filtering for a port by checking the box. This parameter aff ects
VLAN ingress processing. If ingress filtering is enabled and the ingress port is
Ingress Filter: not a member of the classified VLAN of the frame, the frame is discarded.
Ena bled
Disabled
58
58
By default, ingress filtering is disabled (no checkmark).
Determines whether the port accepts all frames or only VLAN tagged f rames.
This parameter affects VLAN ingress processing. If the port only accepts
tagged frames, untagged frames received on the port are discarded.
Permit Frame Type: Options:
allType
tagged
By default, the field is set to allType.
There are four kinds of Limit Rates:
1. LimitAll
Ingress Rate Control : 2. LimitB
3. LimitM
4. LimitBMUC
Ingress Rate Control
Rate Set up the Rate of Ingress Rate.
[0~1000000]
As GEPON OLT 2 PON OLT SFP Ports of GE1 and GE2 are configured in 1000Mbps Force d
Mode, the switch’s SFP Ports should also be changed to 1000Mbps Forced
Mode if the connection is to be established successfully,. Otherwise, the connection might f ail.
59
59
3.2.11 Port Status
This page displays current port configurations and operating status – it is a ports’ configurations summary table. Via the summary
table, you can know status of each port clearly at a glance, like Port Link Up/Link Down status, Link Speed and Duplex mode.
60
60
3.3 PON Card Management
Double-click the PON Card device node unit in the topology tree or right-click PON Card Management in the interface as the
window shows below:
This page displays the current PON Card Information – it is a PON Card Configuration page. Via the PON Card Conf iguration
page, you can know like PON Card MAC addresses or configure ONU AUTH and etc.
61
61
The popup window includes the following f ields:
62
62
3.3.2 OLT Global Setting
Link Key ExchangeTime: Arranges the time of Link Key, the range is 1 to 65535.
63
63
3.3.3 ONU Auth
PON Port: Allows for selecting which PON port for modif ying.
Password: The password of the user. The allowed string length is 1 to 24.
If want to configure Onu Auth, the user must enable the ONU Auth from Interface inf omraiton
page.
64
64
3.4 ONU Management
Double-click the 2 PON OLT device node unit in the topology tree or right-click Chassis Management in the interface as the
windows show below:
65
65
3.4.1 Basic Configuration
The Basic System page provides information on the current device status. Basic System page helps an OLT administrator to
identify the ONU device’s firmware / hardware version, ONU MAC Address, ONU Line Status and others.
66
66
Uni Num ber: Displays the ONU Uni unmber.
This page allows user to configure the IGMP Fastleave, IPTV Profile and etc.
Object Description
IPTV Profile: Fill the IPTV Profile name which has created from 2 PON OLT IPTV Profile page.
67
67
3.4.3 ONU Multicast Group
In ONU Port Management, you can configure the settings of ONU ports to control the connection parameters like Port Speed,
Duplex mode, Flow Control and Port Auto-Negotiation.
68
68
Figure 3-43 ONU Port Management Screen
Description: Allows user to fill in the words for ONU port 1 or 2 description
69
69
3.4.5 Port Multicast
This page allows the user to modify per port VLAN mode.
70
70
Figure 3-45 MAC Address Management Screen
VLAN Mode: There are four modes, Transparent,Ta g,Tra nsl ateandTrunkmode.
71
71
3.4.7 Port Policying
This page allows user to modify the Port Policy conf iguration.
Cir[0-1000000]: Allows user to fill the Cir value, the range 0~1000000.
Cbs[0-1000000]: Allows user to fill the Cbs value, the range 0~1000000.
72
72
3.4.8 Port Egress
This page allows user to modify the Port Egress conf iguration.
Egress Cir[0-1000000]: Allows user to fill the Egress Cir value, the range 0~1000000.
Egress Pir[0-1000000]: Allows user to fill the Egress Pir value, the range 0~1000000.
73
73
3.5 How to Upgrade 2 PON OLT firmware
For upgrading the 2 PON OLT firmware, you need to have FTP server software. Here we are using Home FTP Server software
f or an example:
2. Press the “New account” on the left column and the FTP Client Editor window appears below like. Please fill in the user
name and password as “user”.
74
74
3. Excute “Start Server” for making connection establish.
4. Copy the 2 PON OLT firmware to the Home Ftp server directory.
For example: C:\Program Files\Home Series\Home Ftp Server
5. Operate EMS utility click 2 PON OLT once excute “Device Upgrade” on the EMS toolbar of Conf ig.
75
75
6. After executing the Device Upgrade, the following window will appear. Please fill in the user name and password as “user”.
7. Press “Find File” button to get 2 PON OLT firmware. Following Step 3, the file should be at “C:\Program Files\Home
8. Press “Download to Device” button for downloading the firmware. After a couple of seconds, the Progress Stat us
“TransmitOK” will appear like the window below:
76
76
9. Press “Upgrade” button for upgrading the firmware. During the period, the Progress Status will show “Upgrading”. After
finishing the upgrading, the Progress Status will show “Upgrade OK”.
10. After finishingh the firmware upgrade, please reboot the 2 PON OLT.
77
77
4. 2 PON OLT OPERATION
4.2 Learning
When one packet comes in from any port, the OLT Switch will record the source address, port number, and other related
information in the address table. This information will be used to decide either forwarding or filtering for future packets.
4.4 Auto-Negotiation
The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth
when a connection is established with another network device (usually at Power On or Reset). This is done by detecting the
modes and speeds at the second of both devices are connected and capable of. Both 10BASE-T and 100BASE-TX devices can
connect with the port in either Half- or Full-Duplex mode
78
78
79
79