V1/50 ®

®
PAGEL-GROUT

PROPERTIES FIELDS OF APPLICATION

 V1/50 (0– 5 mm) grout  universal-grout for precision machines of any kind
V1/10 (0– 1 mm) grout
 turbines, generators, compressors, diesel engines
V1/160 (0–16 mm) grout
and other power equipment operating under heavy
 V1/50 combines the characteristics of V1 and vibration
V12
 anchor screws, levelling units and sole plates
for grouting height from 20-120 mm
 steel and concrete columns
 high flowability, also after 2 hours
 prefabricated concrete units and structural
 cement-based and chloride-free
steelworks
 controlled and even expansion with a rigid bond
 bridge bearings and construction joints
between concrete foundation and machine base
plate  crane rails and radio telescopes
 high early and final strength  steel and blast-furnace plants as well as mines
 low modulus of elasticity in connection with high  paper plants, chemical plants and refineries
bending strength

 resistant to cracks even when having a low

w/c-value (0,35)

 resistant to freeze/thaw cycles, waterproof,

resistant to oil and petrol

 pumpable and easy to pour – even during low

temperatures

 externally tested and factory quality control

according to the “Merkblatt für Vergussmörtel”
(“Leaflet for Grouts”) (DBV)

 permission for use in drinking water areas

Z-3. 21-1461
PA VII-1/419

 “Allgemeine bauaufsichtliche Zulassung”

(General Constructional Permission)
Mo. PA VII-1/419 (DIBt) for the Additive-Concentrate

Technichal Reference Sheet 0201-0203

Status: 02.04
V1/160
®
V1/10
®
V1/50
®
 ®
PAGEL-GROUT

TECHNICAL DATA

TYPE V1/10 V1/50 V1/160

Size mm 0–1 0–5 0–16
Grouting height mm 5–30 20–120 >100
Amount of water % 12–13 10–12 10–12
Material needed kg/dm3 2,00 2,00 2,10
Density of freshly mixed mortar kg/dm3 2,18 2,18 2,21
w/c-value 0,35 0,35 0,35
Workability having 20 °C Min. >120 >120 >120
Flowability (channel) immediately cm 70 70 –
60 Min. cm 68 60 –
measure of extension immediately cm – – 70
(DIN 1048) 60 Min. cm – – 65
Extension 24 h Vol. % 0,5 1,0 1,0
28 d Vol. % 0,5 1,0 1,0
Compressive strength 24 h N/mm2 43 49 51
V1/10, V1/50:4416 cm 7d N/mm2 60 70 70
V1/160:101010 cm
28 d N/mm2 87 90 91
90 d N/mm2 100 110 98
Bending strength 24 h N/mm2 6 7 7
4416 cm 7d N/mm2 8 8 8
28 d N/mm2 10 10 10
90 d N/mm2 10 10 10
E-Modul (cylinder) 7d N/mm2 33.800 33.000 34.500
90 d N/mm2 39.800 39.300 40.100
All test data are values derived under normal climate conditions. 23/50-2

Testing temperature: 20 °C
Additive : General Construction Permission Nr. Z-3.21-1461
Corresponding Certificate Nr. 219000
Storage: 12 months in sealed container, dry
Packaging: 25-kg-bag
Hazard class: no dangerous substance, observe safety data sheet
GISCODE: ZP1

Development of compressive strength (V1/50): Development of expansion:

N/mm 2 Vol.
%
110

100 1,0

90 0,9

80 0,8

70 0,7

60 0,6

50 0,5

40 0,4

30 0,3

20 0,2

10 0,1

1 3 7 28 90 3 6 9 12 18 24
days hours

V1/50 ®
V1/10 ®
V1/160®
 ®
PAGEL-GROUT

APPLICATION

SURFACE: Clean thoroughly, free of loose and unsound material, remove any cement slurry by means of hydraulic water-
blasting or similar till carrying capacity of grain structure is reached. Sufficient adhesion must be granted (i. m.
 1.5 N/mm2). Prior to grouting, the surface must be wetted continuously for approx. 6 hours till saturation.
FORMWORK: Must be of rigid construction, with sand or dry mortar being placed around the concrete base carefully to
prevent leakage.
MIXING: The grout is ready for use, only water is to be added (10–12 % or 2.5–3 l per bag). Measure out the correct
quantity of water and fill two thirds of this into a concrete mixer, add the dry mortar and mix for about
3 minutes. Then fill in the remaining water and mix for another 2 minutes. Grouting then should take place
immediately.
GROUTING: Place the mixed grout from one side or corner only in one continuous pour. When grouting large areas we
suggest to pour starting from the middle – using a pipe or funnel. On machine installations fill the anchor bolt
pockets first (up to approximately top of anchor bolt pockets) and then the underside of the machine. Potlife:
approx. 120 min.
CAUTION: Open areas must be protected against wind, draught and premature evaporation by using for example plastic
foil or O1 PAGEL-CURING AGENT.
Grouting shoulders:
Heights and shoulders around base plates must not exceed 50 mm.
Temperature:
Application between 5°C und 35 °C, low temperature working conditions retard the strength development and
reduce the flowability while high temperatures accelerate the same.
Non-Iron-Metals:
Cement as well as all cement-bound building materials may under certain circumstances cause a coming-off
of non-iron-metals in the application area (for exemple aluminium, copper, zinc) please ask for our technical
service.

DIN 1045 AND PAGEL-GROUT

Having prefabricated units grout is being used according to DIN 1045 (6.7.1) for joints, between
components and overlyings.
PAGEL-GROUT belongs according to DIN 1045 to the subject heading cement mortar (2.1.3.1)
and is in need of a General Construction Permission with a Corresponding Certificate for the additives.
PAGEL-CONCRETE-GROUT belongs to the subject heading concrete (BI and BII) and meets
most of the demands of a concrete with special characteristics (6.5.7) (resistant to water, highly
resistant to frost, highly resistant to chemical attacks).
Soucre material for PAGEL-GROUT:
Cement according to DIN 1164
Surcharge: according to DIN 4226 (eFT)
Additional material: General Construction Permission.
Additives: General Construction Permission.

FIELDS OF APPLICATION

 universal-grout for precision machines of any kind

 turbines, generators, compressors, diesel engines and other power equipment operating under heavy vibration

 anchor screws, leveling units and sole plates

 steel and concrete columns

 prefabricated concrete units and structural steelworks

 bridge bearings and construction joints

 crane rails and radio telescopes

 steel and blast-furnace plants as well as mines

 paper plants, chemical plants and refineries

V1/160®
V1/10®
V1/50®
 ®
PAGEL-GROUT

FIELDS OF APPLICATION

funnel

for pump
Air vent Air vent

The information provided in this leaflet, is supplied by our consulting service and is the
end result of exhaustive research work and extensive experience. They are,
however, without liability on our part, in particular with regard to third parties
proprietary rights, and do not relieve the user of the responsibility for verifying that the
products and processes are suitable for the intended application. The data
presented was derived from tests under normal climate conditions according to DIN
50014 and mean average values and analysis. Deviations are possible when delivery SPEZIAL-BETON GMBH & CO. KG
takes place. Given that recommendations may differ from those shown in this leaflet
written confirmation should be sought. It is the responsibility of the purchaser to WOLFSBANKRING 9 · D-45355 ESSEN
ensure they have the latest leaflet issue and that its contents are current. Our
TEL. +49 (0)2 01–6 85 04-0 · FAX +49 (0)02 01–6 85 04-31
customer service staff will be glad to provide assistance at any time. We appreciate the
EN ISO 9001
interest you have shown in our products. This technical data sheet supercedes
INTERNET: WWW.PAGEL.COM · E-MAIL: [email protected]
previously issued information. Please find the latest leaflet issues at www.pagel.com.

V1/50 ®
V1/10 ®
V1/160
®

QS-Formblatt 02/04 Rev. 07