STRUCTURE QUESTION (PAPER 2 - SECTION A)

Understanding Waves (Trial MRSM 2009)

1. Diagram 1 shows a photograph taken from a ripple tank experiment to investigate the
pattern of water waves.

Diagram 1

The frequency of the vibrator is 20 Hz.

(a) What is meant by frequency?

……………………………………………………………………………………….
(1mark)
(b) The distance between A and B is 5 cm.

(i) What is the wavelength of the water wave?

……………………………………………………………………………….
(1mark)

(ii) Calculate the speed of the water wave.

(2mark)

( c) Predict the frequency of the water waves if the speed of the water increases.

…………………………………………………………………………………………..
(1mark)

1
Reflection of waves (Trial SPM 2007)
2. Diagram 2.1 shows a submarine transmitting ultrasonic waves directed at a big rock on
the sea bed. After sometime, the submarine detects the wave again.

Diagram 2.1

(a) State the wave phenomenon involved.

……………………………………………………………………........................
[ 1 mark ]

(b) Explain why the submarine used ultrasonic wave but not ordinary sound wave?

...................................................................................................................................
[ 2 marks ]

(c) (i) Calculate the distance of the submarine from the big rock if the submarine
detects the second wave after 1.5 seconds.
[Velocity of ultrasonic wave = 1560 ms-1]

[ 2 marks ]
(ii) Diagram 2.2 shows how the pulses of the transmitted ultrasonic wave is displayed
on the screen of a cathode ray oscilloscope (CRO).

Diagram 2.2

2
 On Diagram 2.2 draw the pulses of the wave received by the submarine after 1.5
seconds later. Given the time base of the CRO is 0.5 s/cm.
[ 2 marks ]

Diffraction Of Waves

3. Diagram 3.1 shows the arrangement of Young’s double slit experiment. A white light
source is passed through a blue filter to produce a monochromatic light.
Diagram 3.2 shows the pattern of the fringes formed on the screen when a blue filter is
used.

Diagram 3.1

Diagram 3.2

3
 (a) What is the meaning of monochromatic light?

......................................................................................................................................................

[1 mark]

(b) Why bright fringes and dark fringes are observed on the screen as shown on Diagram 3.2?

...................................................................................................................................................
[2 marks]

(c) In the experiment, the screen is placed at the distance of 1.5 m from the double-slit.
The separation distance between the double-slit is 0.5 mm while the total separation of
four successive dark fringes is 4.05 mm. Calculate the wavelength of the blue light.

[2 marks]

Sound Waves

4. Table 4 shows five different waves with their wavelengths respectively.

Wave Wavelength (m)

Sound 5 x 10-1
Radio 1 x 103
Micro 1 x 10 -2
Light 5.5 x 10-7
X- ray 5 x 10-9

Table 4

(a) State the type of sound waves.

...................................................................................................................
[1 mark]

(b) (i) Which of the following waves has the highest frequency?
.............................................................................................................
[1 mark]
(ii)State a reason for your answer in 4 (b) (i)

..............................................................................................................
[1 mark]

4
 (c ) Sound waves are used to determine the depth of a lake. The frequency and
Wave length of the sound waves are 2 500 Hz and 0.5 m respectively. The reflected
sound wave is received after 2.0 s transmitted into the lake. Calculate

(i) the velocity of the sound wave

[2 marks]

(ii) the depth of the lake

[2 marks]
Sound Waves
5. Diagram 5 shows sound wave is produced when a man rubbed his moistened finger
around the rim of a glass filled with water.

Diagram 5

(a) What type of wave is a sound wave?

………………………………………………………………………………………………
[ 1 mark]

(b) What happen to the loudness of the sound wave if the man rub the glass harder?
Give reason for your answer.

………………………………………………………………………………………………
[2 marks]

(c ) What happen to the pitch of the sound wave if the man rub the glass filled with less
volume of water? Give reason for your answer.

……………………………………………………………………………………………………
[2 marks]

5
(d) Sound wave can be used to treat kidney stone without surgical .The treatment is called as
Extracorporeal Shock Wave Lithotripsy (ESWL) that uses sound wave from an out
through the urinary tract.

Table 5 contains three types of ESWL treatments to break kidney stone.

Table 5

6
 Based on Table 5, state the suitable treatment to break kidney stone effectively based on
the following aspects:

(i) Frequency of wave transmitted

.............................................................................................................................

Reason

..............................................................................................................................
[ 2 marks]

(ii) Type of reflector

..............................................................................................................................

Reason

...................................................................................................................................
[ 2 marks]

(iii) Type of medium in Column X

...................................................................................................................................

Reason

..................................................................................................................................
[2 marks]

(e) Based on the answer in 8(d) , choose the most suitable type of treatment to break kidney
stone more effective.
.....................................................................................................................................
[ 1 mark]

Electromagnetic Waves
6. Diagram 6 shows a group of waves in the electromagnetic spectrum arranged accordingly
based on their frequencies and wavelength. The energy of the wave decreases from right
to left and it propagates at the same speed.

7
 Diagram 6

(a) In Diagram 6 , X –ray is represented by

……………………………………………………………………………………

[ 1 mark]

(b) Electromagnetic waves is a wave which direction of vibration of particles is

……………………………..
to the direction of propagation of the waves.

Tick (√ ) the correct answer in the box provided.

parallel

perpendicular

[ 1 mark]
(c ) Based on Diagram 6,

i. state the change of wavelength of the wave from right to the left

……………………………………………………………………………

[1 mark]

ii. state the relationship between the wavelength and effect of diffraction of
the wave.

………………………………………………………………………………
[1 mark]

8
 7. Diagram 7 shows the electromagnetic spectrum.

Diagram 7

a. Based on the Diagram 7, state the name of component P.

.........................................................................................................................................................

[ 1 mark]

b. Compare the frequency of Radio wave and Gamma Ray.

................................................................................................................................................................

[ 1mrk]
c. Name one electromagnetic wave which has longer wavelength than X – ray.

..................................................................................................................................................................
[ 1 mark]

d. What is the difference between electromagnetic wave and the sound wave ?

..................................................................................................................................................................
.

[1 mark]
8 -1
e. Given that the speed of an electromagnetic wave is 3 x 10 ms .
Find the radio wavelength which has frequency 0f 3.2 kHz.

[1 mark]

9
 8. (a) Diagram 8.1 shows the wave pattern formed by water waves from two coherent
sources S1 and S2 in a ripple tank.

Diagram 8.1

(i) Name point P.

………………………………………………………………………………………
[1 mark]

(ii) Explain how point P occurs.

…………………………………………………………………………………………

………………………………………………………………………………………….
[2 marks]

(b) Diagram 8.2 shows a Young’s double-slit experiment using blue light as source.

Diagram 8.2

10
 (i) Underline the correct answer in the bracket to complete the sentence below.
Point M is a (bright, dark) fringe.
[ 1 mark]

(ii) What happens to the distance between two consecutive bright fringes if blue light is
replaced with red light?

…………………………………………………………………………………….

……………………………………………………………………………………...

[1 mark]

(c) An engineer student conduct a study on noise level produced by aircraft engine during take-
off. The soundproofing materials lining the cabin floor is to reduce the noise in the cabin.

Table 8.3 shows the four aircrafts with their respective soundproofing characteristics.

Aircraft Wave phenomenon in noise Soundproofing material Thickness of the

simulator soundproofing material
P Constructive Interference Non porous Thin
Q Destructive Interference Non porous Thick
R Destructive Interference Porous Thick
S Constructive Interference Porous Thin
Table 8.3

Based on Table 8.3, state the suitability characteristics of the aircraft to reduce the noise level
produced by the aircraft.
Give reasons for the suitability of the characteristics.

(i) Wave phenomenon in noise simulator.

……………………………………………………………………………..

Reason
……………………………………………………………………………….
[ 2 marks]

(ii) Soundproofing material

…………………………………………………………………………………

Reason
………………………………………………………………………………………
[2 marks]

11
 (iii) Thickness of the soundproofing material
………………………………………………………………………………………

Reason
…………………………………………………………………………………………
[2 marks]

(iv) Using your answer in 8 (c ) determine the most suitable aircraft that can reduce the
noise level.
………………………………………………………………………………………
[1 mark]

UNDERSTANDING & CONCEPT QUESTION (4M)

SBP Trial 2015 (No.12)

1. Diagram 1.1 shows a Barton’s pendulum which consist of six pendulums tied to a
horizontal string. When X is displaced and released, it will oscillate with its natural
frequency.

Diagram 1

(i) What is the meaning of natural frequency? [1 mark ]

(ii) Explain how the phenomenon of resonance occur in Diagram 1. [4 marks]

Trial Sabah 2015

2. Diagram 2 shows a submarine using a sonar system. Explain why ultrasonic wave is
used in sonar system instead of radio wave.

12
 Diagram 2
(3marks)

Trial Perak 2015

3. (a) What is meant by waves?

(b)During high tide, a boat which parks behind retaining wall rocking up and down
more vigorously. Explain the statement.
(4 marks)

MODIFICATION
FULL FORMAT ESSAY QUESTIONS
PAPER 2 SECTION B (20M)

Trial Perak 2009 (No.10)

1. A group of students are walking in front of two loud speakers connected to a signal
generator. They stop when they hear the loudest sound. The positions of the students
when they stop are shown Diagram 10.1.

Diagram 10.1

13
Two dippers connected to a vibrator are vibrating simultaneously on the water surface of a ripple
tank. The water wave pattern produced is shown in Diagram 10.2. Wavelength of the water
waves,  can be determined by the formula as follows :
𝑎𝑥
= 𝐷

Diagram 1.2

(a) (i) What is the definition of waves?

(1 mark)

(ii)What do you observe about the sources of the waves, the positions of the students
and the waves patterns in Diagram l0.l and Diagram 10.2? Use these observations
to deduce a physics concept and state the concept.
(5 marks)

(b) Base on the interference of water waves shown in Diagram l.2, draw the
interference pattern. Your drawing should include the following aspects:

(i) the crest and trough of the waves

(ii) a
(iii) x
(iv) D
(4 marks)

(c ) Diagram 1 0.3 shows the new hall in Sekolah Menengah Kebangsaan Sungai
Perak. A musical concert will be held at the hall in few months’ time.

Diagram 1.3

14
Observe Diagram 1.3 carefully, there are some improvements can be made to enhance the sound
effect. Using appropriate physics concept, explain the use of suitable equipment and furnishing
to improve the sound effect of the concert.
Your answer should include the following aspects:

(i) Distance between of two stereo speakers

(ii) Positioning of speakers and microphones
(iii) Furnishing of the hall and other aspects
(10 marks)

2. Diagram 10.1 shows the wave fronts pattern of the water waves, before and after passing
through small gaps. Diagram 10.2 shows the wave fronts pattern of same water wave,
before and after passing through bigger gap.

Diagram 1.1 Diagram 1.2

(a) (i) Name the wave phenomenon shown in Diagram 2.1 and 2.2.
[1 mark]

(ii) Based on the Diagram 2.1 and Diagram 2.2, compare the wave patterns before
through the gaps, the wave patterns after through the gaps and the wave length
before and after passing through the gaps. Relate the size of the gaps and the wave
patterns. Deduce a relevant physics concept regarding the wavelengths in this
situation.
[5 marks]

(b) Diagram 2.3, shows movement of sea water wave front from the open sea towards
the seashore.

15
 Diagram 2.3

Explain why the water at the cape has high wave and the water at the bay is calm.
(4 marks)

(b) Diagram 2.4 shows a tsunami warning system located at the sea to detect tsunami
in advance and issues warning to the shore region.

Diagram 2.4

Indonesia's system fell out of service in 2012 because the detection buoys were no longer
operational. Suggest modifications that can be made to the system, so that if can work
effectively to detect tsunami due to earthquake or volcano eruptions. State and explain
the modifications based on the characteristics of material which is used for detection
buoys and anchor, the co

[10 marks]\

16
 MAKING DECISION
FULL FORMAT ESSAY QUESTIONS
PAPER 2 SECTION C (20M)
Trial Negeri Sembilan 2017

1. Waves can be used for sea floor mapping.

Diagram 1.1

(a) What is meant by longitudinal waves?

[1 mark]
(b) Based on Diagram 1.1
(i) Find the depth of deep area when the ship transmits a wave pulse to the
seabed and receives an echo 0.2 s later. The speed of the waves in sea water is
1500 m s-1.
[2 marks]

(ii) Find the difference in depth of deep and shallow region if the time for wave to
propagate from the seafloor of shallow region to the ship is 0.07 s.
[3 marks]

(c) Diagram 1.2 shows a girl standing 50 m in front of a building, firing a shot. A boy
who is standing beside the girl, hears two bangs apart with a lower loudness for
second sound.

17
 Diagram 1.2

(i) Explain why the boy heard two explosions.

(iii) Explain why the second sound is lower in loudness

[4 marks]

(d) As a researcher, you want to use waves to determine sea floor mapping in small area
at the ocean. Explain the characteristic of waves that should be used to gain the
information about the ocean.

Table 1.1

Explain the suitability of each aspect and then determine the most suitable waves.
Give reason for your choice.
[10 marks]

18
Trial Negeri Pahang 2017

2. Diagram 12.1 shows the wave pattern when water wave moves from sea to the beach.
The wavelength changed as the wave approach the beach.

Diagram 12.1

(a) What is the meaning of wavelength?

[1 mark]
(b) Explain why the waves at the beach has low amplitude.
[4 marks]
(c) A port is in a process of deepening and broadening to load more cargo ships. Diagram
2.2 shows the original area of the port and the area that will be developed. Table 2
shows four design proposal for the development of the port.

Diagram 2.2

19
 Table 12.1
You are asked to investigate of each design proposal to make sure the safety of cargo
ships. Explain the suitability of each characteristics of the design. Determine the most
suitable design. Give reasons for your choice.
[10 marks]

(d) A plane wave with wavelength of 2 cm and velocity of 8 cms-1 propagate from
region A to region B. When the wave arrived at region B, the wavelength change to
12 cms-1.Calculate
(i) the wavelength in region B.
(ii) the frequency
(5 marks)

20