MANUAL-1

[ FOR USER’S ]

DONGMUN HIGH FREQUENCY GENERATOR

DIG SERIES (FOR 1-TUBE)

DONGMUN CO., LTD

USER’S MANUAL DONGMUN

NOTICE 1

1. Thank you for purchasing DIG SERIES(For 1-Tube), Dongmun High Frequency
Generator for X-ray radiographic systems.

2. This manual is designed to ensure correct use and operation of DIG-Series HFG.
Please read all the lines thoroughly before you use the generator.

3. The responsibility about the use of medical apparatus and management of

maintenance is in a user’s side. No responsibility is taken by Dongmun for any
infringement of patients or other rights of the third parties which many results
from the use of this manual.

4. Incorrect use and operation exceeding described conditions in this manual may
occur damage of the device and shorten its life. Particular attention must be paid to
all the warnings, cautions and notes incorporated herein.

5. Always keep the manual at hand for your reference.

NOTICE 2

1. This equipment should be used only by the legally qualified persons and practi-
tioners

2. For the safe installation

a. Please avoid wet and humid locations.
b. Install the product where there is no adverse effect from pressure, temperature,
humidity, ventilation, dust, sulfur and other air pollutants.
c. Protect the product from slope, vibration, and shock.
d. Do not install the product where chemicals are stored or gases are generated.

-1-
USER’S MANUAL DONGMUN

e. Check the frequency, voltage, and current of power supply.

f. Check the earth ground power about the electric discharge and polarity.

3. Before the operation of the machine

a. Examine contact of switch, polarity, dial setting, and display, and check if the
product properly operates.
b. Check the safety of the ground power connections.
c. Check the correctness and safety of the cable and plug connections.
d. Be careful that mixed use of the machine may give wrong diagnostic results
and damages to the device.
e. Check the exterior circuits, which occur direct physical contact to the patient.
f. Check the earth ground power about the electric discharge and polarity.

4. During the operation of the machine

a. Do not exceed the designated time for diagnosis and cures.
b. Monitor the conditions of device and influence on the patient.
c. When you find any troubles about generators or patients, stop the operation
of the machine and take appropriate measures for the safety of the patient.
d. Be careful that the patient should not touch the device.

5. After the operation of the machine

a. Turn off the power of the machine after returning the operation switches and
scales to the original position in accordance with the prescribed regulation.
b. Do not pull out the plugs and lines with compelling forces and it can hurt the
connections.
c. For the safe storage and installation
d. Please avoid wet and humid locations.
e. Install the product where there is no adverse effect from pressure,
temperature, humidity, ventilation, dust, sulfur and other air pollutants.
f. Protect the product from slope, vibration, and shock.
g. Do not install the product where chemicals are stored or gases are generated.

6. If the device is broken, mark proper description and ask repairs to the engineer.

7. Do not modify the machine.

8. Inspections and maintenance

a. All device and parts should be checked on the regular basis.

-2-
USER’S MANUAL DONGMUN

b. If you operate the device after long period of non-use, check the safety and
conditions of the machine.
9. Operate the machine in correct ways according to the manuals.
10. Be careful about following cautions
a. Wear the lead apron in order to prevent the x-ray irradiation.
b. Regular inspection should be executed about leakage dose and irradiation
meter.
c. Be careful about the x-ray exposures.
d. Do not exceed the maximum weight for the x-ray tables.

NOTICE FOR THE OPERATION 1

1. If you find any troubles about the conditions of patients or machine, stop the
operation and take appropriate measures.

2. For the need of emergency power cut-off, use the power switch on the operation
panel. Do not randomly cut off the power during operation.

3. Be careful about using the exposure and hand switches on the operation panel.
You can make exposures anytime under normal conditions.

NOTICE FOR THE OPERATION 2

1. As this device is not protective against exposure, do not use combustible or

blasting gases such as narcotic drugs, oxygen and hydrogen near the working
locations.

2. Do not use the machine during the warning signs of the earthquake. As well, the
security of the machine must be checked after the occurrence of the earthquake.

3. In case any troubles happen to the machine, turn off the power and mark
appropriate sign such as “Do not use this machine” and ask repairs to the
engineers.

4. Regular inspection is required to the device and ask any questions to the sales
division of the Dongmun.

-3-
USER’S MANUAL DONGMUN

-4-
USER’S MANUAL DONGMUN

OTHER NOTICE AND ADVISES

1. Power on and off

Do not turn off the machine for 30 seconds after turning on the power. Please
wait at least 30 seconds for the resupply of the power.

2. Regarding the operation environment

a. X-ray room
Practitioners should take enough cares for the release of the x-rays out of the
x-ray room. This device is designed to be protective against humidity and
dust. However, if you use the machine at the place with high humidity and dust,
it can shorten the life of electronic insult and grow rust on the metal parts.
b. Do not leave the machine exposed to the strong direct sunlight.

3. Exposure of the x-rays

a. Be careful about using the exposure and hand switches on the operation
panel. You can make exposures anytime under normal conditions.
b. Take enough cares in order not to make excessive radiation on the same
body locations.

4. Each cable has enough length and flexibility but do not bend the cable forcibly.
.
・
DANGEROUS

Do not use the machine with following equipment.

*The equipment, which release electronic waves such as mobile phone, radios,
wireless toys, and etc. The officials in hospital ought to give enough advises and
education for the operator of the machine, doctors, patient and other the third
parties.

-5-
USER’S MANUAL DONGMUN

SYMBOLS AND TERMS

The following symbols will be used in this manual: their meanings and applications
are described further below.

It warns of the conditions and situations, if not taken

DANGER over or avoided, that cause heavy damages to people and
even the death.

It warns of the conditions and situations, if not taken

WARNING over or avoided, that could cause heavy damages to
people or cause unrepeatable damages to the equipment.

It warns of the conditions and situations, if not taken

over or avoided, that could cause damages to people, or
CAUTION
to the equipment.

-6-
USER’S MANUAL DONGMUN

WAIVER CLAUSE

Poskom do not take responsibility for the following causes for damage and repairs.

1. Any installation, movement, modification and repairs by other engineering services,

which was not designated by Dongmun.

2. Troubles and causes to our machine incurred by other equipment.

3. Any troubles and defects by the use of other parts, which is not designated and
recommended by Dongmun.

4. Damages or accident caused by the disobedience to the cautions and regulations

in user’s manual.

5. Troubles and damages created by inappropriate environment prescribed in this

manual regarding use of the powers, installation and working places.

6. Any defects and causes occurred by natural calamity such as fire, earthquake,
windfall and thunders.

7. Accident and damage happened by the use beyond the original purpose of the
machine.

8. Diagnosis for the patient should be under the doctor’s responsibility. Dongmun do
not take responsible for the conditions and results of the medical prescriptions.

-7-
USER’S MANUAL DONGMUN

SCOPE AND PERIOD OF WARRENTY

1. All Dongmun products are guaranteed warranty of 1(one) year for any disorder or
discrepancy occurred from normal use and operation of product.

2. Service fee is charged for the following cases.

- Malfunctioning after the period of warranty
- Disorder caused by fire, earthquake, or lightening
- Inappropriate movement or negligence of product
- Disorder from repair or reconstruction by other than Poskom service agent or
other designated ones.

3. Note that defects not related to the main functions of the product are not eligible
for this warranty.

4. Requirements for Service

a. Stop using the product when a problem is found, and check the manual for a
solution.
b. Turn off the product before service request, and check the model number,
serial number, the date of purchase before calling the service center.

5. Defects or depreciation in appearance is not eligible for refund or change.

6. Dongmun is not responsible for indirect damage related to the use of products.

7. Dongmun is not responsible for injury or damage after the end of warranty
period.

8. All detailed adaptability warranties and other warranties are subjected to this
statement.

-8-
USER’S MANUAL DONGMUN

SECTION 1.

COMPOSITION/SPECIFICATION

-9-
USER’S MANUAL DONGMUN

1.1. COMPOSITION

The electric composition block diagram of DIG-Series is shown in Fig 2-1.

EM swich HF
Power AD/DC HV TANK
Supply Delay Convertor DC/AC Inverter
EM swich X-ray
TUBE

IGBT
Driver

Stater

OP
PANEL
HT CONT
Collimator
PWR

FILAMENT

IF

AEC ION
Chamber

Fig 1-1 COMPOSITION OF THE HFG

AC input voltage is converted into DC voltage by a single-phase all wave rectifier

circuit. This DC voltage is inverted in high-frequency voltage of about 20kHz by
IGBT inverter.
The high-frequency voltage is converted into the 40 (+20kV/-20kV) to 125kV
(+62.5kV/-62.5kV) DC high voltage by a high-voltage transformer and the multi-
voltage rectifier circuit. This DC high voltage is supplied to an X-ray tube through a
high-voltage cable, and PWM INV controls this X-ray tube voltage. Modulating the
Filament voltage controls the tube current.
.
The operation panel can operate selection in each mode of operation and control,
selection and setting of conditions. These operation conditions are transmitted by
the communication system from OP-CONT to HT-CONT.
HT-CONT controls the output of a high-voltage generator according to the

- 10 -
USER’S MANUAL DONGMUN

instructions from OP-CONT.

The flow of the control signal of X-ray exposure is shown in the following Fig 1-2.

Operation Panel

High Voltage Generator

Main CPU

A/D CONV D/A CONV

PWM kV FB PWM

kV, mA FB Amp

Filament
mA FB
Drive
circuit rms/DC CONV

IGBT AEC
FIL. INV.

HV Trans kV
FIL. Trans. mA

A C
FIL.
X-ray TUBE

ION Chamber

Fig 1-2 CONTROL SIGNAL OF X-RAY EXPOSURE

- 11 -
USER’S MANUAL DONGMUN

1-2. SPECIFICATION

DIG-325 32kW
DIG-525 40KW
1 Rating Output
DIG-650 50kW
DIG-1150 80KW

Radiography 40-150kV (1kV STEP)

2 Tube Voltage kV
Fluoroscopy 40-125kV (1kV STEP)
10, 12.5, 16, 20, 25, 32, 40, 50, 63, 80,
100, 125, 160 mA (small focus)
Tube Current Radiography
3 200, 250, 320, 400, 500, 630, 800 mA
mA (large focus)
Fluoroscopy 0.1~4.0 mA (0.1mA Step)
4 kV Accuracy ±10%
5 mA Accuracy ±15%
0.001 sec – 10 sec (38 step)
6 Timer Range
0.003 sec ~ 6 sec (PXR-161 Only)

DIG-325 0.1 mAs ~ 630 mAs

DIG-525 0.1 mAs ~ 630 mAs
7 mAs Range
DIG-650 0.1 mAs ~ 800 mAs
DIG-1150 0.1 mAs ~ 999 mAs

20mAs or more: Less than 15%

8 mAs Accuracy
Less than 20mAs: Less than 20%
9 Display Method LED digital indication
10 Setting Method Sheet Push Switch
Self-diagnostic
11 Error Code Indication
Function
12 Technique Selection Manual, APR, AEC
13 APR 216 exam techniques
14 AEC (Option) Ionization Chamber 5 (Option)
15 Display (OP Panel)
kV 3 Digit LED
mA 3 Digit LED
mAs 4 Digit LED (change into sec)
Time 4 Digit LED (change into mAs)
Selection/setting LED (36)
Alarm LED (2)
16 Weight 62 kg
Operation Panel 2 kg

- 12 -
USER’S MANUAL DONGMUN

1-3. ELECTRICAL REQUIREMENT

Model 1-Tube DIG Series

Line Nominal Voltage 1 phase 200V/220V/240V
Automatic Line Compensation Range ± 10%
Frequency 50 Hz / 60 Hz
Line Impedance Less than 0.12Ω
Grounding conditions Based on the local regulation

- 13 -
USER’S MANUAL DONGMUN

1-4. PROPER ENVIRONMENT

A. Avoid following places for the normal operation and safe storage.
a. Where the equipment is exposed to water vapor.
b. Where the equipment is exposed to direct sunlight.
c. Where the equipment is exposed to dust.
d. Where the equipment is exposed to high humidity.
e. Where there is a ventilation problem.
f. Where the equipment is exposed to salty atmosphere.
g. Where the equipment is exposed to chemicals or gas.

B. Keep away from the place with strong vibration and maintain proper environment
and conditions.

*Operation Environment
Temperature range 10°C ~ 40°C,
Relative Humidity Range 30% ~ 75% RH
Others No Direct Sunlight
No combustible and corrosive gases

C. For safe storage and transportation, you must keep following range of
temperature, humidity and atmosphere.

*Environment for Storage and Transportation

Temperature range -25°C ~ +60°C
Relative Humidity Range 10% ~ 95% RH
Air Pressure 700hPa ~ 1060hPa
Others No corrosive gases

- 14 -
USER’S MANUAL DONGMUN

SECTION 2

DISPLAY/FUNTION

- 15 -
USER’S MANUAL DONGMUN

2-1. STRUCTURES AND SIZE

- 16 -
USER’S MANUAL DONGMUN

fig. 2-1 STRUCTURE AND FIGURES (16kW ~ 50kW)

fig. 2-2 STRUCTURE AND FIGURES (50kW & 80kW 3Phase)

- 17 -
USER’S MANUAL DONGMUN

400. 0 mm

200. 0 mm
36. 0 mm

42. 0 mm

fig.2-3 CONFIGULATION OF OPERATION PANEL

- 18 -
USER’S MANUAL DONGMUN

2-2. OPERATION PANEL

22
10 12
16
9 3 4 11 5 1 2 6

23 24

13 14 15 18 19 20 17 21 25 7 8

Fig 2-4 Operation Panel

1 Power on switch 14 APR exposure region selection/display

2 Power on switch 15 APR exposure direction selection
3 kV Display Segment 16 Patient size selection and memory
4 kV Setting Switch 17 AEC Reset/ mode display
5 mAs/sec Setting Switch 18 Backup release switch
6 mAs/sec Setting Switch 19 Density setting/display switch
7 X-ray Exposure Ready Switch 20 Bucky selection/display
8 X-ray Exposure Switch 21 AEC mode and field selection switch
9 “OVER” Display (Red) 22 X-ray exposure hand switch
10 “ERROR” Display (Red) 23 Small focus display
11 X-ray Exposure ready sign 24 Large focus display
12 X-ray Exposure Display (Yellow) 25 AEC film/screen combination selection
13 APR Menu Selection Switch

- 19 -
USER’S MANUAL DONGMUN

(1) Power On Switch

Turn on the power of generator.

(2) Power Off Switch

Turn off the power of generator.

(3) kV Setting/Display Segment

kV

Button increases the kV value of tube voltage whereas decreases kV.

If you keep buttons pressed, the value of KV will be increased or decreased

continuously.

(4) mA Setting/Display Segment

mA

Button increases the mA value of tube voltage whereas decreases mA.

If you keep buttons pressed, the value of mA will be increased or decreased

continuously.

(5) mAs/Sec Setting/Display Segment

mA s
sec

Button increases the mAs/sec value of tube voltage whereas

decreases mAs/sec. If you keep the button pressed, the value of mAs/sec will
be increased or decreased continuously.

- 20 -
USER’S MANUAL DONGMUN

(6) mAs/Sec Selection Switch

mA s
sec

mA s

sec

The mAs or sec radiography mode is selected.

The selected radiography mode is displayed with LED.

(7) X-ray Exposure Ready Switch

It circulates the rotor and controls the heat of the filament that makes ready
actions for the x-ray exposure.

(8) X-ray Exposure switch

Press the exposure switch after the ready sign is lighted on.

(9) “Over” LED (Red)

The over LED is lighted on when the exposure conditions exceeds the normal
standards. You cannot make exposure while the over LED is lighted on.

(10) “Error” Indication (Red)

The LED is lighted in case of errors.

(11) X-ray Exposure Ready LED (Green)

The exposure ready sign is lighted on when it is at the ready condition.

(12) X-ray Exposure LED (Yellow)

The X-ray exposure sign is lighted on during the X-ray exposure.

(13) APR Mode Setting Switch

It operates the on/off of the APR mode.

- 21 -
USER’S MANUAL DONGMUN

(14) APR Exposure Region Selection/Display switch

It operates the selection of exposure regions and the selected location will be
displayed on the LED.

(15) APR Exposure Direction Setting Switch

1 2 3 4

It operates the selection of exposure directions the selected direction will be

displayed on the LED.

(16) Patient Size Selection and Memory Switch

S IZE LL L M S SS BABY

It operates the selections of patient size. The selected size will be displayed on
the segment. Save the changed APR conditions by pressing the size switches.

*You can set the exposure conditions (kV, mA and mAs/sec) by selecting the
exposure regions, direction and patient size. Each condition can be changed
and stored by the exposure size switch.

(17) AEC Reset/Mode Display Switch

If the x-ray exposure is closed early by the AEC backup timer, the AEC mode
LED will blink off and the buzzer sounds. The next exposure is forbidden until
the reset switch is pushed.

(18) Backup Release Switch

Release the back-up conditions.

(19) Density Setting/Display Switch (AEC/APR mode)

-3 0 +3

It selects the density level of the exposure and increases or decreases the
mAs/sec under the APR mode.

- 22 -
USER’S MANUAL DONGMUN

(20) Bucky Selection/Display

Select and display BUCKY1 (table) and BUCKY 2(stand).

(21) AEC Mode and Field Selection Switch

It selects the field on the AEC mode. Each LED represents the physical location
of irradiation detector and the combination of designated field is available.

(22) X-ray Exposure Hand Switch

It circulates the rotor and controls the heat of the filament that makes ready
actions for the x-ray exposure. Press the exposure switch after the ready sign
is lighted on. Please touch off from the button after the LED is lighted on.

(23) Small Focus Display (Green LED)

It is displayed when the small focus is selected.

(24) Large Focus Display (Green LED)

It is displayed when the large focus is selected.

(25) Film/Screen Combination Selection

It operates the adjustment of kVp and divided by low speed, medium speed
and high speed (200, 400, 800)

- 23 -
USER’S MANUAL DONGMUN

SECTION 3

OPERATION/EXPOSURE

- 24 -
USER’S MANUAL DONGMUN

3-1. POWER ON & OFF

1. Power-on Switch

a. Press the Power on switch.

b. If the power is turned on, initial condition of equipment will be checked.

c. During the checking actions, "-" mark will be displayed on kV, mA, and
mAs/sec display segment.
d. After the check, it displays radiographic conditions.
e. Radiographic conditions display the final status of the previous operation.

2. Power-off Switch

a. Press the Power off switch.

b. Please turn off the power supply except the time of use.

Do not turn on and off the power of the equipment

continuously except emergent cases.
CAUTION
Have the interval of 30 seconds or more between ON-OFF
operations of a power supply.

- 25 -
USER’S MANUAL DONGMUN

3-2. SELECTION OF THE RADIOGRAPHY METHOD

There are radiography modes shown below in this equipment.

a. Manual radiography mode

Radiography conditions are performed by manual setup.

b. APR radiography mode

You can select the radiography region; direction and patient size on the control
panel and make x-ray exposure with automatically set radiography conditions.
Each radiography conditions can be changed and saved.

c. AEC radiography mode

It helps to produce the optimal images by AEC (Automatic Exposure Control
Option) Menu selection.

- 26 -
USER’S MANUAL DONGMUN

3-3 SETTING MANUAL RADIOGRAPHY

1. Select the manual radiography mode

Check if the APR mode or AEC mode are chosen. If they are selected in APR or
AEC mode, please press APR or AEC setting switch, and release the setup
conditions.

2. Setting tube voltage "kV"

Set up the tube voltage with “kV” setting switch.
Setting range: 40kV – 125 or 150kV (1kv step)

3. Setting tube current “mA”

Set up the tube current with “mA” setting switch.
Setting range:
10、12.5、16、 20、 25、32、40、50、
63、 80、 100、125、160 ｍＡ ….（Small Focus）
200、250、320、400, 500, 630, 800, 999 ｍＡ ….（Large Focus）

Model mA Range Remark

DIG-325 10~400mA
DIG-525 10~500mA
DIG-650 10~630(800)mA
DIG-1150 10~999mA

4. Setting the radiography mode (mAs/sec radiography)

Select the radiography mode with mAs/sec selection switch (display).

"sec" radiography makes x-ray exposure by set-up time

"mAs" radiography makes x-ray exposure by the setup time of current.

-A setup of mAs value in “mAs" mode

-mAs value is chosen with the mAs/sec setting switch.
Setting range：0.1 mAs～800 mAs
Step： 0.1、0.2、0.3、0.4、0.5、0.6、0.8、
1.0、1.3、1.6、2.0、2.5、3.2、4.0、5.0、6.3、8.0、10、12.5、

- 27 -
USER’S MANUAL DONGMUN

16、20、25、 32、40、 50、 63、80、100、125、160、200、

250、320、400、500、630, 800, 999 mAs

Model mAs Range Remark

DIG-325 0.1~630mAs
DIG-525 0.1~630mAs
DIG-650 0.1~800mAs
DIG-1150 0.1~999mAs

-A setup of sec value in “sec” mode

-Sec Value is chosen with the mAs/sec [5] setting switch.
Setting range：0.001 sec～10 sec
Step： 0.001、0.002、0.003、0.004、0.005、0.006、0.008、0.010、
0.013、0.016、0.020、0.025、0.032、0.040、0.050、0.063、
0.080、0.100、0.125、0.160、0.200、0.250、0.320、0.400、
0.500、0.630、0.800、1.00、 1.25、 1.60、2.00、 2.50、 3.20、
4 .00、 5.00、6.30、8.00, 10.00 sec

About "OVER" display of radiography conditions

When set-up radiography condition "kV", "mA", and "mAs
NOTICE or sec" exceeds the permissible value of equipment, OVER
sign lights up.
X-ray exposure is prohibited when the over sign is turned
on. Please reset the appropriate radiography conditions.

Model sec Range Remark

DIG-325 0.001~10 sec
DIG-525 0.001~10 sec
DIG-650 0.001~10 sec
DIG-1150 0.001~10 sec

3-4. SETTING APR

1. Selection of APR mode

- 28 -
USER’S MANUAL DONGMUN

Choose APR mode with the (13) APR selection switch and the LED displaying APR
mode will be lighted on the upper left of the OP panel.

2. Selection of Radiography Regions

Choose the radiography regions with (14) radiography region selection switch
and you can move the LED display with up/down button. The available option is 9.

3. Selection of Radiography Directions

Choose the radiography directions with (15) radiography direction switch out of 4
options.

4. Selection of the Radiograph Size

Choose the radiography size with (16) patient size selection switch out of 6
options, [LL] [L] [M] [S] [SS] [BABY].

*The radiography condition will be selected after the selection of the

radiography symbol, radiography region, and radiography method.
As well the order for the selection will not be changed.

5. Selection of the Density

Adjust the mAs/sec settings with the density switch.
Increase the conditions of mAs/sec if the Density is +1 ~ +3.
Increase the conditions of mAs/sec if the Density is -1 ~ -3.

6. Change of the Radiography Conditions

You can change the selected radiography conditions with the same method of
the 3-3 manual radiography condition setting. The over LED can be lighted
from time to time when the radiography conditions are changed. Please be
careful about the setting of the radiography conditions since the x-ray
exposure is prohibited under the case.

7. Memory of the Changed Radiography Conditions

You can save the conditions changed above. The method for store is pressing
the selected switch for 2 seconds until the buzzer sounds.

- 29 -
USER’S MANUAL DONGMUN

Memory of the changed Radiography condition

Be careful that other radiography conditions can be
CAUTION selected if you choose the selected radiography size
switch. You cannot save the memory while the over LED
is lighted and when the density setting is not 0.

3-5. AEC RADIOGRAPHY

1) Selection of AEC radiography mode

In order to use AEC mode, the DIP S/W 5 of operation panel should be turned on.
When DIP S/W 5 is turned off: AEC mode is not available.

2) Switch [17] is the AEC mode selection switch.

Ion-chamber is chosen with switch [18] after you select the AEC mode with switch
[17].

3) The selection of density in the AEC mode can adjust the level of x-ray exposure
levels.

4) “Ready” action is not operated if the bucky and field are not chosen after the AEC
mode selection.

3-6. RADIOGRAPHY

1. Photography Preparation
After setting up radiography conditions, assemble the cassette equipped with the
film on the x-ray table.
If the X-ray irradiation field lamp switch attached to the variable X-ray beam-
limiting device is pushed, the lamp will be lighted up. X-ray irradiation field is
adjusted with a radiography position, and radiography preparation is ended.

- 30 -
USER’S MANUAL DONGMUN

2. X-ray Radiography Using Operation Panel

1) Press the X-ray exposure preparation switch. Ready LED will be lighted on when
all preparation work is completed.
2) If you press the x-ray preparation switch and exposure switch at the same time,
the x-ray shooting will be started.
3) X-rays exposure LED will be lighted on and the buzzer sounds during the
exposure.

3. X-ray Radiography Using Hand-Switch

1) Press the hand switch one time and make it at ready condition. The x-ray ready
LED will
be lighted on when it is prepared to make exposure.
2) When the equipment is ready to make exposure, press the hand switch again
and the x-ray shooting is started.
3) During exposure, the exposure LED will be lighted on and the buzzer sounds.

4) If the X-ray exposure LED is turned off or buzzer does not sound, it means
the radiography work is completed. Then, you can stop pressing the hand
switch.
5) If you touched out and stopped x-ray shooting during exposure, the check
code will be displayed.

If you touch out from the hand switch during exposure,

CAUTION the x-ray shooting is stopped and you cannot get clear
pictures. Please touch off your hand after the x-ray
exposure signs and the buzzer sound are turned off
except the case you want to stop the x-ray exposure
urgently

- 31 -
USER’S MANUAL DONGMUN

You cannot make radiography while the over LED is lighted

on. Change the conditions for the radiography in those
CAUTION
cases.

SECTION 4

TROUBLES

- 32 -
USER’S MANUAL DONGMUN

- 33 -
USER’S MANUAL DONGMUN

4-1. ERROR CODE AND CHECK CODE

In case any problems happen during the operation of the device, they will be
indicated on the kV/mA segment.

A. Error Code
The error code is displayed when problems, such as abnormalities, occur to the
equipment. While the error code is displayed, radiography operation is forbidden
for safety. A power supply should be switched off and on again and an error code
will be cleared. If the problem of equipment is not solved at the time of the power-
supply re-switched on, the error code will be displayed again.
Since it is the failure of equipment when an unusual state is not recovered, please
inform the service section of our company or our agent.

B. Check Code
Unlike an error code, a check code is the warning sign when wrong operations are
applied by the user. X-ray radiography operation is forbidden for the safety during
the check code. The way to release a check code is pressing the WR switch for 2
seconds. CH01 will be released if thermal switch is off during the re-supply of the
power.

- 34 -
USER’S MANUAL DONGMUN

ERROR CODE LIST

Error
Code DESCRIPTION ACTION
Err 01 CHARGE MONITOR ERROR (HT-CONT)
Err 02 OVER TIME ERROR (OP PANEL) AT STAND BY RESUPPLY OF
Err 03 READY-OUT SIGNAL ERROR AT SAND BY THE POWER
Err 04 X-RAY OUT SIGNAL ERROR AT STAND BY
Err 05 READY SWITCH INPUT ERROR AT STAND BY
Err 06 X-RAY SWITCH INPUT ERROR AT STAND BY
Err 07 HAND SWITCH INPUT ERROR AT STAND BY
Err 08 HAND SWITCH X-RAY INPUT ERROR AT STAND BY
Err 09 ROTOR DETECTER SIGNAL AT STANDBY
Err 10 FILLAMENT CURRENT DETECTER ERROR AT STANDBY
Err 11 ‘kV FEEDBACK ERROR AT STANDBY
Err 12 ‘mA FEEDBACK ERROR AT STANDBY
Err 13 ROTOR DETECTER ERROR AT EXPOSURE
Err 14 FILLAMENT CUREENT DETECTER ERROR AT EXPOSURE
Err 15 ‘kV FEEDBACK ERROR DETECTER ERROR AT EXPOSURE
Err 16 ‘mA FEEDBACK DETECTIVE ERROR EXPOSURE
Err 17 NOT DEFINED
Err 18 X-RAY TIME OVER IN SEC MODE
Err 19 X-RAY TIME OVER IN mAs MODE
Err 20 X-RAY TIME OVER IN AEC MODE
Err 21 HV INTERLOCK ERROR
Err 22 IGBT FEEDBACK ERROR
Err 23 ‘kV FEEDBACK OVER DETECTER ERROR AT EXPOSURE
Err 24 ‘mA FEEDBACK OVER DETECTER ERROR AT EXPOSURE
Err 25 NO ZERO-CROSS OR NO INPUT
Err 26 ZERO-CROSS OVER OR WRONG INPUT FREQUENCY
Err 27 BUCKY 1 OK SIGNAL ERROR (HT-CONT)
Err 28 BUCKY 2 OK SIGNAL ERROR (HT-CONT)
Err 29 AEC A/D DATA-IN ERROR (HT-CONT)
Err 30 AEC A/D DATA-IN ERROR (HT-CONT) AT NON-EXPOSURE
Err 31 I/F BOARD CONDITION ERROR
Err 32 AEC BOARD CONDITION ERROR
Err 33 SMALL-FOCUS SELECTION ERROR (HT-CONT)
Err 34 LARGE-FOCUS SELECTION ERROR (HT-CONT)

- 35 -
USER’S MANUAL DONGMUN

CHECK CODE LIST

CHECK CODE DESCRIPTION Measure

Ch 01 TUBE THERMOSTAT OPERATION Reset
Ch 02 When another switch is pushed during exposure Release by
Ch 03 When ready switch on OP PANEL is detached during “WR” switch
exposure
Ch 04 When X-RAY switch on OP PANEL is detached during
exposure
Ch 05 When a hand switch (ready) is detached during
exposure
Ch 06 When a hand switch (X-RAY) is detached during
exposure
Ch 07 Shortage of power-supply capacity for exposure Power-supply
re-switch
Ch 08 Simultaneous exposure prohibition Reset
Ch 09 Warning to X-rays room door opening
Ch 10 AEC Level Error

* CH01 is will be released if the TUBE terminal switch is off, in case resupply of the
power.

- 36 -
USER’S MANUAL DONGMUN

SECTION 5

MAINTANENCE

- 37 -
USER’S MANUAL DONGMUN

5-1. MAINTANANCE AND PERIODIC OPERATOR

Maintenance has check menus carried out daily by the user and periodic
inspection by technical service engineers who completed special training
programs on the repair of the generator.

User checks items based on " Daily Checking Items by the operator " and should
keep data records.

The following checks and maintenance procedures, together with the suggested
intervals, are the manufacturer’s recommendation for most effective Periodical
Maintenance schedule for this generator.

Exclusively service personnel specifically trained on medical X-ray generator

must perform service tasks here described.

The first periodic maintenance service should be performed six (6) months after
installation, and the subsequent service every twelve (12) months.

When a trouble and a poor part are discovered, please stop use of equipments,
turn off a power supply, and contact a near service station.

- 38 -
USER’S MANUAL DONGMUN

5-2. DAILY CHECKING ITEMS BY THE OPERATOR

Check following items according to the regular inspection plans.

Please refer to the daily inspection method regarding the way of checking.

In order to avoid the danger of an electroshock, please do not

CAUTION remove the cover of equipment by any means.
Only the expertise person who received training performs the
check and repair accompanied by removal of a cover.

Check item INTERVAL

Daily Weekly Monthly
Air Conditioner ○
Temperature and Humidity ○
Operation Panel ○
Radiographic Condition ○

Radiation field lamp ○

Warning light in use ○

- 39 -
USER’S MANUAL DONGMUN

5-3. WAYS OF DAILY CHECKING (CHEKING MENUS)

Please check clear environment inside the operation room and x-ray room.
The system is designed to operate with normal conditions under following
environment. Please keep following temperature and humidity.

• The recommended operating environment is follow.

Temperature : +10 - +35 ℃
Relative humidity: 45 – 85 %, 45~65 % (X-ray room)

In the environment with a rapid change of temperature and

CAUTION humidity, it is easy to generate dew condensation.
Installation of an air conditioner is recommended.

The ingredient that makes silver etc. sulfurate may be

CAUTION contained in the exhaust gas of an automatic development
machine. Please install the independent air conditioner.

• Operation Panel
Please check whether each switch of an operation panel lights up.
When you clean the surface of an operation panel, it should be wiped with the
soft and fine cloth. When using a cleaner, it is made to contain in cloth and is
used.

Don't blow a liquid upon the operation panel directly.

It goes into the inside of equipment from a crevice, and
CAUTION
becomes the cause of failure.

- 40 -
USER’S MANUAL DONGMUN

• The check of radiographic condition

Before the commencement of work, trial radiography is performed and film density,
unevenness, and etc. are checked.

• Radiation field lamp

It confirms whether a radiation field lamp lights up before the commencement of
work.

• Warning light in use

It confirms whether warning light in use switch on before the commencement of
work.

- 41 -
USER’S MANUAL DONGMUN

In this record paper, results of check are filled and kept.

DAILY CHECK RECORD

Type/Name ：
X-ray Room No.：
Date ：
Performed by ：

Interval Result
Check item Daily Weekly Good/No Good

Air Conditioner ○
Temperature and Humidity ○
Operation Panel ○
Radiographic Condition ○

Radiation field lamp ○

Warning light in use ○

Memo：

- 42 -
USER’S MANUAL DONGMUN

5-4. PERIODIC INSPECTION

It is a check report by the expertise person. The periodic inspection is performed

according to this item.

DIG-550 HF Check Report Approval by a user

S/N： Date：
S/S： Performed by：

Client name: Address:

Installation date: Check classification

Last-time checked date:

Check Table (1/2)

No Check item Result No Check item Result
1 Appearance of equipment 15 Condition of tube busing
2 Warning light in use 16 Tube cable check
3 Installation situation 17 Isolation resistance
4 Operation of each switch 18 Input voltage of power supply

5 Wiring connection 19 Sequential operation at Power

ON/OFF
6 Lighting state of each lamp 20 Check inside AC power-supply
voltage
7 Digital display
* Collimator : 12V
8 Check of fuses
* Warning light : 100V
9 High-voltage cable and 21 Check inside DC power-supply
Bushing check for High- voltage
voltage tank and X-ray tube * Main Capacitor bank
10 Quantity of insulated oil * Filament board voltage
* PWR board voltage
11 Bolting of bushing
TP1 = +24 V
12 Focal roughness TP3 = +12 V
13 Rotation sound of Rotor TP5 = +5 V

- 43 -
USER’S MANUAL DONGMUN

14 Exchange grease for High- TP6 = -12V

voltage cable / Bushing

Check Table (2/2)

No Check item Result No Check item Result
22 Check of calibration data at the 26 Pre-heat adjustment of
time of installation Filament
23 Voltage at the time of constant 27 Opening-and-closing
rotation of Rotor condition of Collimator
V 28 I luminance of Collimator
lamp
24 Tube voltage check and 29 Light field and Radiation
adjustment field
25 Tube current check and 30 AEC adjustment (option)
adjustment

＊Sign and Result of maintenance

Sign Result Sign Result Sign Result
V Normal. T Tighten M Measurement
A Adjusting E Replacement S Data Store
R Repair C Cleaning
F Supplement O Oiling

Memo:

Used Measuring Instrument

Measuring Instrument Maker/Model/S.N. Term of validity
DVM
‘mAs meter
Non-invasive kV meter
‘mA meter

- 44 -
USER’S MANUAL DONGMUN

Scope

- 45 -