Scribd
Upload
323 views1 page

At13 303

This document provides specifications for a Band III circularly polarized antenna panel suitable for mounting on triangular masts. The panel operates from 174-216 MHz with a peak gain of 4.2 dB and 3dB beamwidth of 85 degrees in both planes. It can handle up to 6 kW of peak sync power and has circular or elliptical polarization. Mounting and electrical connection details are provided along with performance data for arrays of 1-8 panels mounted at various heights.

Uploaded by

KAREN ROMAN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
323 views1 page

At13 303

This document provides specifications for a Band III circularly polarized antenna panel suitable for mounting on triangular masts. The panel operates from 174-216 MHz with a peak gain of 4.2 dB and 3dB beamwidth of 85 degrees in both planes. It can handle up to 6 kW of peak sync power and has circular or elliptical polarization. Mounting and electrical connection details are provided along with performance data for arrays of 1-8 panels mounted at various heights.

Uploaded by

KAREN ROMAN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

AT13-303

Band III 2 crossed dipoles circular/elliptical polarization panel ● Especially suitable for triangular masts

Electrical Specifications
Frequency range 174 – 216 MHz
Peak gain 4.2 dB (ref. /2 dipole) (circular polarization)
3 dB beam width E-plane: 85º H-plane: 85º
Polarization Circular/Elliptical
Impedance 50 Ohm
VSWR 1.1:1 (with circular polarization)
Maximum power handling peak sync. 2 kW 3.5 kW 6 kW
Maximum power handling RMS 1.4 kW 2.5 kW 4.2 kW
Connector type (2 per antenna) 2 x DIN 7/16 2 x EIA 7/8” 2 x DIN 13/30
Non Gas barrier on input
Pressurization
pressurized connector

Mechanical & Environmental Specifications


Materials Hot dip galvanized steel
Dimensions (W x D x H) 960 x 602 x 960 mm
Maximum wind speed 200 km/h
Wind load (front) 610 N (@160 km/h)
Wind load (lateral) 473 N (@160 km/h)
Weight 35 kg
Typical mounting Triangular arrangement tower
Clamp type To Ø 80 – 115 mm pipe
Vertical spacing 1300 mm
Grounding DC grounded
Temperature range -40°C to +80°C
Humidity 100%

Antenna System Characteristics


Number Number Peak gain Weight Wind load System
of Bays ant. per bay (dBd) (kg) (@160 km/h) height (mm)
2 1.8 70 1.3 kN
1 960
3 0.1 105 2.0 kN
2 4.8 140 2.6 kN
2 2260
3 3.1 210 4.1 kN
2 7.8 280 5.3 kN
4 4860 NOTES:
3 6.1 420 8.2 kN
2 9.6 420 7.9 kN
6 7460 - Table supplies data up to 8 bays only for
3 7.8 630 12.2 kN simplification purposes; systems with more
2 10.8 560 10.6 kN bays are available.
8 10060 - Null fill, beam tilt, harness & feeder losses
3 9.1 840 16.3 kN
NOT INCLUDED.
- Wind load & weight figures without
The above specified gain must be understood for circular polarization considering cables, splitters & hardware.

E-mail: [email protected]
RYMSA RF will reserve the right to make any changes without notice. Web: www.rymsarf.com

You might also like