Technical Data Sheet

Approved 462;463;9880;464;1500;7021 1,2 462 epoxy ^(ValidationDate) 1

Jota Armour

Product description
This is a three component abrasion resistant polyamine cured epoxy coating. Specially designed as an anti-skid
coating. Suitable on metallic substrates coated with approved primers and on concrete coated with suitable
sealer.

Typical use
Can be used on helidecks, walkways, ramps, weigh bridge decks, decks in general where abrasion resistance
and non-slip properties are required.
Other

Approvals and certificates

Approved to UK Defence Standard 80-134/1 for the Royal Navy, flight decks, hangar decks and weather decks
Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 4, suitable for decks and walkways.
Additional certificates and approvals may be available on request.

Colours
grey 038, green 137, BS 640

Product data
Property Test/Standard Description
STANDARD GRADE
Solids by volume ISO 3233 90 ± 2 %
Gloss level (GU 60 °) ISO 2813 semi gloss (35-70)
Flash point ISO 3679 Method 1 35 °C
Density calculated 1,43 kg/l
VOC-EU IED (2010/75/EU) (calculated) 123 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 158 g/l

WINTER GRADE
Solids by volume ISO 3233 84 ± 2 %
Flash point ISO 3679 Method 1 31 °C
VOC-EU IED (2010/75/EU) (calculated) 144 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 143 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
Gloss description: According to Jotun Performance Coatings' definition.

Date of issue: 28 April 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jota Armour

Film thickness per coat

Typical recommended specification range
STANDARD GRADE

Dry film thickness 750 - 3000 μm

Wet film thickness 830 - 3330 μm
Theoretical spreading rate 1,2 - 0,3 m²/l

WINTER GRADE
Dry film thickness 750 - 3000 μm
Wet film thickness 890 - 3570 μm
Theoretical spreading rate 1,1 - 0,3 m²/l

Anti-slip roughness profile of coating limits accuracy on film thickness measurements. Approximate spreading
rate for 1000 μm dry film is 8 m²/kit from practical testing.

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Spray: Gravity Feed Hopper Gun or other suitable equipment. Consult Jotun for additional
information, as required.

Product mixing ratio (by weight)

Mix Comp A and Comp B, then add Comp C (graded aggregate), 10 minutes prior to use.

Date of issue: 28 April 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jota Armour

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Drying and Curing time

Substrate temperature 0 °C 5 °C 10 °C 23 °C 40 °C

STANDARD GRADE
Surface (touch) dry 8h 5h 3 h
Walk-on-dry 24 h 14 h 6 h
Dry to over coat, minimum 28 h 14 h 6 h
Dried/cured for service 14 d 7d 2 d

WINTER GRADE
Surface (touch) dry 22 h 14 h 8h 3h
Walk-on-dry 32 h 24 h 24 h 8h
Dry to over coat, minimum 32 h 24 h 24 h 8h
Dried/cured for service 28 d 14 d 14 d 4d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

STANDARD GRADE
Induction time 10 min
Pot life 2h

WINTER GRADE
Pot life 1h

Date of issue: 28 April 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jota Armour

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 120 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy, epoxy mastic, zinc epoxy

Subsequent coat: epoxy, epoxy mastic, polyurethane

Packaging (typical)
Jota Armour Comp A 4l
Jota Armour Std Comp B 0.7 l
Jota Armour Wintergrade Comp B 1l
Jota Armour Comp C 4.3 l / 14 kg

The components may be packed as a kit in a 20 l mixing pail.

9 l kit: 4 l Comp A, 0.7 l Jota Armour Std Comp B and 4.3 l / 14 kg Comp C.
9.3 l kit: 4 l Comp A, 1 l Jota Armour Wintergrade Comp B and 4.3 l / 14 kg Comp C.

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Jota Armour Comp A 48 month(s)
Jota Armour Std Comp B 48 month(s)
Jota Armour Wintergrade Comp B 48 month(s)
Jota Armour Comp C 120 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Date of issue: 28 April 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jota Armour

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 28 April 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com