HP-5101AC

User Manual
08-2012 / v1.1

0
 COPYRIGHT

Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission from Edimax Technology Co.,
Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability, or fitness for any particular purpose.
Any software described in this manual is sold or licensed as is. Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from
any defect in the software. Edimax Technology Co., Ltd. reserves the right to
revise this publication and to make changes from time to time in the contents
hereof without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more information about this product,
please refer to the user manual on the CD-ROM. The software and specifications
are subject to change without notice. Please visit our website www.edimax.com
for updates. All brand and product names mentioned in this manual are
trademarks and/or registered trademarks of their respective holders.

Edimax Technology Co., Ltd.

Add: No. 3, Wu-Chuan 3rd Rd., Wu-Ku Industrial Park, New Taipei City, Taiwan
Tel: +886-2-77396888
Email: [email protected]
 Contents
Chapter 1: Introduction ..................................................................................................................................... 1
1.1 Product Features .................................................................................................................................. 1
1.2 Application ........................................................................................................................................... 1
1.3 Compatibility ........................................................................................................................................ 2
1.4 System Requirements .......................................................................................................................... 2
Chapter 2: About the Product............................................................................................................................ 3
2.1 LED Definitions ..................................................................................................................................... 3
2.2 Interface ............................................................................................................................................... 4
Chapter 3: Getting Started ................................................................................................................................. 5
3.1 Hardware Installation .......................................................................................................................... 5
3.2 Creating a Powerline Network ............................................................................................................. 6
3.3 Creating an Encrypted Powerline Network with Two Adapters .......................................................... 7
Chapter 4: Utility Software Installation ............................................................................................................. 8
Chapter 5: Using the Utility Software .............................................................................................................. 14
5.1 Main Tab ............................................................................................................................................ 14
5.2 Privacy Tab ......................................................................................................................................... 17
5.3 Diagnostics Tab .................................................................................................................................. 18
5.4 About Tab ........................................................................................................................................... 19
Chapter 6: Powerline Network Management with Group Button .................................................................. 20
6.1 Forming a AV500 Logical Network ..................................................................................................... 20
6.2 Joining a Network .............................................................................................................................. 21
6.3 Leaving a Network & Joining another Network ................................................................................. 22
Chapter 7: Troubleshooting ............................................................................................................................. 23
 Chapter 1: Introduction

1.1 Product Features

 Integrated with power socket just as an additional wall socket

 Easy plug-n-play setup and 128-bit AES security
 Max. powerline speed up to 500Mbps
 Backward compatible with 200Mbps powerline adapters
 Features energy saving mode to reduce power consumption
 Integrated power socket with noise filter
 Powerline transmission range up to 300 meters

1.2 Application

 High-definition (HD) and standard-definition (SD) video distribution

 Broadband Internet sharing
 Internet Protocol Television (IPTV) and Voice over Internet Protocol (VoIP)
applications

1
1.3 Compatibility

200Mbps (Edimax HP-200x series) and 500Mbps (Edimax HP-500x series) powerline
adapters are able to communicate directly with one another. 200Mbps and 500Mbps
powerline adapters can be used on the same household electric wiring as 14Mbps &
85Mbps powerline adapters (Edimax HP-85XX series) without interfering, but are not able
to communicate directly with 14Mbps and 85Mbps powerline adapters.

1.4 System Requirements

 Computer with Ethernet port running Windows XP/Vista/7, Linux, MAC OS X and
any other operating system.
 Any connected devices must feature a network port.
 Utility software supports Windows XP/Vista/7.

2
 Chapter 2: About the Product

2.1 LED Definitions

LED Status Description

Green LAN port connected
Blinking LAN activity (transferring data)
LAN
Off LAN port not connected
The green indicator turns on and the yellow indicator
blinks slowly when the device is detecting a
powerline link.
Green/Yellow
The green indicator turns on and the yellow indicator
PLC
blinks quickly to indicate data is being transferred
over the powerline link.
Off No other PLC device detected
Green Powered on
PWR Off Powered off

Note: The device will enter standby mode, and all LEDs will extinguish, after
5 seconds without any data transfer, including when the Ethernet cable is
disconnected. The Power LED will flash once every 15 seconds.

3
2.2 Interface

Interface Description
Integrated The integrated electrical socket enables additional terminal
Power Socket devices or multiple socket to be connected to the adapter, just
as a normal wall socket would.
Ethernet Port This is a Fast Ethernet port for connecting to a computer or
other devices with a network port.
Group/Reset Creates an encrypted powerline network group automatically
(press the button for less than 3 seconds).
Leaves an encrypted powerline network group
(press the button for 5~8 seconds).
Restores the powerline adapter to factory defaults (press the
button for 10~15 seconds).

4
 Chapter 3: Getting Started

3.1 Hardware Installation

1. Always plug the powerline adapter directly into a power socket. Never plug it into a
multiple socket or uninterruptible power supply (UPS).

2. If you need to use a multiple socket for additional network devices,

then connect the multiple socket to the integrated power socket of the adapter, and
plug the powerline directly into a power socket, as shown below. The power socket of
the adapter features a filter function which is able to improve the data transmission in
the network.

5
3.2 Creating a Powerline Network

1. Connect a powerline adapter to your router via Ethernet cable, and then plug it into a
power socket.

2. Connect another powerline adapter to your computer, and then plug it into a power
socket.

Note: You can also connect the adapter to a printer, set top box, gaming console, TV or
other device with a network port, to add the device into the powerline network.

3. Make sure that the PLC and LAN LEDs light up on both PLC adapters.

4. The computer and the router will be connected to the powerline network automatically.

6
3.3 Creating an Encrypted Powerline Network with Two Adapters

Once both adapters have been successfully connected, press the “Group/Reset” button
of each adapter for less than 3 seconds within 2 minutes. The adapters will
automatically generate a random password to encrypt the powerline network.

Note:
 To add additional adapters into the encrypted powerline network or to remove
an adapter from the powerline network, please refer to the Chapter 6 in the
manual
 If the powerline adapter in your network does not feature a “Group/Reset” or
an “Encrypt” button, you can use the utility software as an alternative. For
more details please refer to Chapter 5 in the manual.

7
 Chapter 4: Utility Software Installation

You can manage all the connected powerline adapters with the utility software. Only install
the utility software when you need to add other powerline adapters without “Group” or
“Encrypt” button.

Step 1 Before installing the utility software, make sure that no other powerline utility is
installed on your computer. If any other utility software is installed, uninstall it and
reboot the computer.

Step 2 Insert the CD into your CD-ROM drive. When the following “Autorun Wizard”
appears, select your model.
Note: If autoplay is installed on your computer, the “Autorun Wizard” will start
automatically. Otherwise, please go to Autorun folder in the CD and execute the
“AutoRun.exe” program.

8
Step 3 Then click “Setup Utility”.

Step 4 If you have not installed WinPcap version 4.1.2 (or higher) on your computer
before, please click “OK” to install the utility. The wizard will guide you through the
setup process.

9
10
Step 5 When the “Edimax PowerLine Utility” setup wizard appears, click “Next” to
continue.

11
Step 6 In the “License Agreement” screen, please select “I Agree” and then click “Next” to
continue.

Step 7 Select where you want to install the utility software, and then click “Next”.

12
Step 8 If you confirm to install the utility, click “Next”.

Step 9 After the installation is complete, click “Close”.

Step 10 An icon will appear on your desktop. Double click the icon to open the utility
software.

Note: You can manage all the connected powerline adapters with the utility
software. However, installing the utility software is optional.

13
 Chapter 5: Using the Utility Software

5.1 Main Tab

The “Main” tab provides a list of local or remote powerline adapters in the network.
You could manage the remote powerline adapters (those on your circuit, but not directly
connected to your computer) here.

Upper Panel - Local Device(s) on your computer

The upper panel displays local powerline adapters connected to the computer’s
network port. In situations where there are more than one local device being connected,
such as a USB or an Ethernet adapter, the user can select the local device by clicking on it
and then click the “Connect” button. The status area above the button indicates that your
PC is connected to which device. Once connected to the local device, the utility will
automatically scan the power line periodically for any other powerline devices. If no local
powerline devices are discovered, the status area above the connect button will indicate
with a message “ADAPTERS NOT DETECTED’.

14
 If you want to upgrade firmware of the adapter directly connected to your computer,
please click “Upgrade firmware” button. The dialog box will be shown as below, please click
“Browser” button to choose the PIB and firmware files you wish to update and then click
“OK” button.

Note: Please be sure you have selected the correct model firmware, or the device may be
damaged.

Lower Panel - Powerline Devices detected

The lower panel displays remote powerline adapters in the network. The following are
descriptions of every setup items:

Item Descriptions
Device Name This column shows the default device name, for example:
“Device 2”, “Device 3”. If you want to change the name,
please click “Rename” button to edit the name.
Password (DEK Password) This column by default is blank. In order to manage the
powerline adapters, you have to enter the password (DEK
password) of the adapter. The DEK password is printed on
the label located in back of the powerline adapter. After
you have entered the correct password, this column will
show the password.

To set the password of the adapter, first select the adapter

by clicking on its name and then click “Enter Password”
button. A dialog box will appear as below. Please type the
password and click “OK” button.

15
Quality The status of the connection quality will be shown here.
Rate (Mbps) Shows the current data rate of the powerline adapter.
MAC Address The adapter’s MAC address will be shown here.
Rename Select an adapter and click “Rename” to rename the
adapter.
Enter Password Select an adapter and click “Enter Password” to set the
password for the adapter.
Add This button is used to add a remote powerline adapter
which is not the existing network. Click this button and the
following dialog box will appear. Please enter both device
name and the password and click “OK” button.

Scan Click “Scan” and the utility software will perform an

immediate scan of other powerline adapters. By default,
the utility automatically scans every few seconds.

16
5.2 Privacy Tab

In the “Privacy” tab, you can create a private network by changing the default network
name.

The following are descriptions of every setup items:

Item Descriptions
Private Network Name Almost all of the powerline adapters shipped with the same
network name . With the same network name, all the
powerline adapters can be connected directly.

If you want to create private network, please enter the new

network name and then click “Set Local Device Only” or
“Set All Devices” button.
Use Default (Public Click this button and the in the “Private Network Name”
Network) column will be shown the default name.
Set Local Device Only This button is used to change the network name of the
local device only. Once you have changed the network
name of the local adapter only, the adapters seen on the
“Main” tab prior to this will be no longer present in the
network.
Set All Devices This button is used to change the network name of all
adapters that appear in the “Main” tab. If the network
17
 name is modified to anything other than the default, the
network type in the “Main” tab will be changed to
“Private”.

5.3 Diagnostics Tab

The “Diagnostics” tab displays the system information and history of all remote
devices.

The upper panel displays technical data concerning the software and hardware on the
host computer and the lower panel displays the history of all remote devices.

18
5.4 About Tab

The “About” tab contains some basic information about the software.
In “Preferences” panel, you can enable or disable the “AutoScan” function. When the
function is enabled, the utility will auto scan the powerline adapters in the network and
show the adapters in the “Main” tab. If you have disabled this function, please click “Scan”
button in the “Main” tab to scan the adapters manually.

19
 Chapter 6: Powerline Network Management with Group Button

This section demonstrates how to add or remove devices from a powerline network
with the “Group/Reset” button.

6.1 Forming a AV500 Logical Network

When two devices with different group keys are connected to the same powerline and
you want them to form a logical network, follow the following procedures:

Step 1 Press and hold the “Group/Reset” button on adapter A for less than 3 seconds. The
Power LED will start to blink.

Step 2 Within 120 seconds after the Power LED starts blinking on adapter A, press the
“Group/Reset” button on adapter B for less than 3 seconds.

Step 3 Wait for the connection to be established.

20
6.2 Joining a Network

If you want to add a new powerline adapter to an existing network, follow the
following procedures:

Step 1 Press the “Group/Reset” button on an adapter in the existing network (adapter A
or B) for less than 3 seconds. The Power LED will start to blink.

Step 2 Within 120 seconds after the Power LED starts blinking on adapter A or B, press
the “Group/Reset” button on the new adapter (adapter C) for at least 3 seconds.

Step 3 Wait for the connection to be established.

21
6.3 Leaving a Network & Joining another Network

If you want to remove a powerline adapter from an existing network and add it to
another network, follow the following procedures:

Step 1 Press the “Group/Reset” button on the adapter to be removed (adapter B) for 5~8
seconds.

Step 2 Wait for adapter B to be disconnected with adapter A & C.

Step 3 Press the “Group/Reset” button on an adapter in another network (adapter D) for
less than 3 seconds. The Power LED will start to blink.

Step 4 Within 120 seconds after the Power LED starts blinking on adapter D, press the
“Group/Reset” button on adapter B for at least 3 seconds.

Step 5 Wait for the connection to be established.

22
 Chapter 7: Troubleshooting

If your powerline adapters have difficulty communicating with each other, try the
following procedures:

 Try power cycling the unit by unplugging it from the electric outlet for 10 seconds and
plugging it in again.
 Hold the “Group/Reset” button down for 10~15 seconds on each unit you are trying to
connect. The units will reset and attempt to establish a connection using factory default
settings.
 Try plugging the powerline adapter into an adjacent electric outlet.
 This powerline adapter should not be used on GFI protected electric outlets, as some
outlets will filter out the powerline signal.
 This powerline adapter should not be used in areas with excessive heat.
 Certain florescent or incandescent lights are noise sources that can degrade
performance.
 If your building has more than one circuit breaker box, your powerline adapters may not
be able to establish a connection across different circuit breaker boxes. In such cases, try
establishing a connection across different circuit breaker boxes by linking two powerline
adapters together with an Ethernet cable.

23
 Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

24
 EU Declaration of Conformity

English: This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2004/108/EC, 2009/125/EC.
Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive
2004/108/EC, 2009/125/EC
Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic
2004/108/EC, 2009/125/EC.
Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi
Dyrektywą UE 2004/108/EC, 2009/125/EC.
Română: Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale
Directivei 2004/108/EC, 2009/125/EC.
Русский: Это оборудование соответствует основным требованиям и положениям Директивы
2004/108/EC, 2009/125/EC.
Magyar: Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek
(2004/108/EC, 2009/125/EC)
Türkçe: Bu cihaz 2004/108/EC, 2009/125/EC direktifleri zorunlu istekler ve diğer hükümlerle ile
uyumludur.
Українська: Обладнання відповідає вимогам і умовам директиви 2004/108/EC, 2009/125/EC.
Slovenčina: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc 2004/108/EC,
2009/125/EC.
Deutsch: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2004/108/EC, 2009/125/EC.
Español: El presente equipo cumple los requisitos esenciales de la Directiva 2004/108/EC, 2009/125/EC.
Italiano: Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili della
Direttiva 2004/108/EC, 2009/125/EC.
Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen van
richtlijn 2004/108/EC, 2009/125/EC.
Português: Este equipamento cumpre os requesitos essênciais da Directiva 2004/108/EC, 2009/125/EC.
Norsk: Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv
2004/108/EC, 2009/125/EC.
Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta
bestämmelser i direktiv 2004/108/EC, 2009/125/EC.
Dansk: Dette udstyr er i overensstemmelse med de væ sentligste krav og andre relevante forordninger i
direktiv 2004/108/EC, 2009/125/EC.
Suomi: Tämä laite täyttää direktiivien 2004/108/EC, 2009/125/EC oleelliset vaatimukset ja muut
asiaankuuluvat määräykset.

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as household or general waste. It
should be handed over to the applicable collection point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.

25
26