

Preface


Open Source Software


SIPROTEC Table of contents


Basics 1
Multifuction Protection 
Mapping 2
7SJ66 
IEC61850 Literature

Mapping 
Index

C53000-L2640-C554-2
Disclaimer of Liability Copyright
We have checked the text of this manual against the hardware and Copyright Siemens AG 2017
software described. However, deviations from the description can- Dissemination or reproduction of this document, or evaluation and
not be completely ruled out, so that no liability can be accepted for communication of its contents, is not authorized except where ex-
any errors or omissions contained in the information given. pressly permitted. Violations are liable for damages. All rights re-
The information given in this document is reviewed regularly and served, particularly for the purposes of patent application or
any necessary corrections will be included in subsequent editions. trademark registration.
We appreciate any suggestions for improvement.
We reserve the right to make technical improvements without no- Registered Trademarks
tice. SIPROTEC, SINAUT, SICAM and DIGSI are registered trademarks
of Siemens AG. Other designations in this manual might be trade-
Document Release V04.10.02 marks whose use by third parties for their own purposes would in-
Edition 12.2017 fringe the rights of the owner.

Siemens Aktiengesellschaft Order No.: C53000-L2640-C554-2

Preface

Purpose of this manual

In this Manual, you will find the
 General information about the effects of configuration of your device to the different Logical
Nodes and DOIs
 Mapping of device relevant information to Logical Nodes as part of protocol IEC61850

Target audience
This manual is intended mainly for all persons who configure, parameterize and operate 
SIPROTEC Devices 7SJ66

Scope of validity of this Manual

SIPROTEC 7SJ66, Versions from 4.30 and higher

Standards
This document has been created according to the ISO 9001 quality standards.

Further Support
If you have questions about SIPROTEC IEC 61850 interface, please contact your Siemens sales
representative.

SIPROTEC, 7SJ66, IEC61850 MAPPING 3

C53000-L2640-C554-2, Edition 12.2017
4 SIPROTEC, 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-2, Edition 12.2017
Open Source Software

The product contains, among other things, Open Source Software developed by third parties. The Open
Source Software used in the product and the license agreements concerning this software can be found in the
Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those
license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the
event of conflicts between Siemens license conditions and the Open Source Software license conditions, the
Open Source Software conditions shall prevail with respect to the Open Source Software portions of the sot-
ware. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software
License Conditions provide for it you can order the source code of the Open Source Software from your Sie-
mens sales contact - against payment of the shipping and handling charges - for a period of at least 3 years
since purchase of the Product. We are liable for the Product including the Open Source Software contained in
it pursuant to the license conditions applicable to the Product. Any liability for the Open Source Software
beyond the program flow intended for the Product is explicitly excluded. Furthermore any liability for defects
resulting from modifications to the Open Source Software by you or third parties is excluded. We do not provide
any technical support for the Product if it has been modified.

SIPROTEC, 7SJ66, IEC61850 MAPPING 5

C53000-L2640-C554-2, Edition 12.2017
6 SIPROTEC, 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-2, Edition 12.2017
Table of contents

1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 Effects of Configuration on the Logical Nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2.1 Function parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2.2 Function parameters SIPROTEC 7SJ66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.3 Allocation of Logical Nodes to Logical Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.4 Logical Node LLN0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.4.1 Logical Device PROT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.4.2 Logical Devices MEAS, DR and EXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.4.3 Logical Device CTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.5 DOI Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.5.1 Logical Device PROT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.5.2 Logical Devices MEAS, CTRL, DR and EXT. . . . . . . . . . . . . . . . . . . . . . . . . . . 28

2 Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2.1 Device (LPHD1, CALH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2.1.1 Error with a summary alarm and Alarm summary event . . . . . . . . . . . . . . . . . . 31
2.2 Oscillographic Fault Records (RDRE1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2) . . . . . . . . . . . . . . . . . . 36
2.3.1 Overcurrent Protection 50, 51 PH (PTOC6, PTOC7, PTOC18, PTOC1) . . . . . 36
2.3.2 Overcurrent Protection 50N, 51N (PTOC8, PTOC9, PTOC2) . . . . . . . . . . . . . . 41
2.3.3 Overcurrent Protection 50N, 51N (PTRC2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3) . . . . . . . . . . . . . . . . 48
2.4.1 Directional Overcurrent Protection 67 (PTOC10, PTOC11, PTOC19, PTOC3) 48
2.4.2 Directional Overcurrent Protection 67N (PTOC12, PTOC13, PTOC20, PTOC4) 54
2.4.3 Directional Overcurrent Protection 67N (PTRC3) . . . . . . . . . . . . . . . . . . . . . . . 59
2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17) . . . . . . . . . . . . . . . . . . 63
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.6.1 Undervoltage Protection 27 (PTUV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.6.2 Undervoltage Protection 27 (PTUV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2.6.3 Overvoltage Protection 59 (PTOV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
2.6.4 Overvoltage Protection 59 (PTOV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5) . . . . . . . . . . . . . . 72
2.8 Motor Protection (PMSS1, PMRI1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
2.8.1 Motor Starting Protection 48 (PMSS1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
2.8.2 Motor Restart Inhibit 66 (PMRI1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

SIPROTEC, 7SJ66, IEC61850 MAPPING 7

C53000-L2640-C554-2, Edition 12.2017
 2.9 Load Jam Protection (PMLJ1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
2.10 Frequency protection 81 O/U (PTUFx, PTOFx). . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2.10.1 Frequency protection 81-1 U (PTUF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2.10.2 Frequency protection 81-2 U (PTUF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
2.10.3 Frequency protection 81-3 U (PTUF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
2.10.4 Frequency protection 81-4 U (PTUF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
2.10.5 Frequency protection 81-1 O (PTOF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
2.10.6 Frequency protection 81-2 O (PTOF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
2.10.7 Frequency protection 81-3 O (PTOF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
2.10.8 Frequency protection 81-4 O (PTOF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.11 QV Protection 27/Q (PTUV9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
2.12 Thermal overload protection (PTTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx) . . . . . . . . . . . . . . . . . 100
2.13.1 Ground Fault Protection 64 (PHIZ1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
2.13.2 Ground Fault Protection 50N(s) (PSDE1, PSDE2) . . . . . . . . . . . . . . . . . . . . . . . 105
2.13.3 51 N(s) (PSDE3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7) . . . . . . . . . . 110
2.15 Automatic Reclosing System 79 (RREC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
2.16 Fault Locator (RFLO1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
2.17 Circuit breaker failure protection 50BF(RBRF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
2.18 Synchronism and Voltage Check 25 (RSYNx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
2.19 Three-pole tripping 52 Breaker (XCBR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
2.20 Tripping Logic of the Entire Device (PTRC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
2.21 Measurement (MMXU1, MSQI1, MMTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
2.21.1 Measures (MMXU1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
2.21.2 Measured values, symmetrical components (MSQI1) . . . . . . . . . . . . . . . . . . . . 135
2.21.3 Power Metering (MMTR1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Literature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

8 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Basics

Basics 1

Contents
This chapter contains general information about the effects of device configuration on Logical
Nodes and DOIs.

1.1 General 10

1.2 Effects of Configuration on the Logical Nodes 12

1.3 Allocation of Logical Nodes to Logical Devices 18

1.4 Logical Node LLN0 22

1.5 DOI Behavior 27

SIPROTEC, 7SJ66, IEC61850 MAPPING 9

C53000-G2640-C554-2, Edition 12.2017
Basics
1.1 General

1.1 General

The protocol IEC 61850 was developed to define a standard that can be internationally
employed for the transmission of power automation system data.
This cross national standard enables an interoperability between automation systems and
devices made by different manufacturers.
7SJ66x can be equipped with an Ethernet module via which the protocol IEC 61850 is
interpreted.
The configuration of the protocol and the integration of the device with redundant IEC 61850
interfaces in your network are performed via the configuration system DIGSI.

Note
The following definitions are taken mainly from standard IEC 61850, Technical Specification
IEC TS 61850-2.

Logical Devices
LD Logical Devices represent a functional structuring of the LN Logical Nodes of a SIPROTEC
device.
The following Logical Devices are present:
 Logical Device Protection PROT

 Logical Device Measurement MEAS

 Logical Device Disturbance Recorder DR

 Logical Device Control CTRL

 Logical Device Extended EXT

Each LD contains LN LLN0 and LN LPHD1.

The allocation of the Logical Nodes to the Logical Devices is listed in Chapter 1.3.

10 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.1 General

Logical Node LN
Smallest part of a function that exchanges data. A logical node is an object defined by its data
and methods.

Data object instance DOI

A Data object is part of a logical node object representing specific information for example status
of measurement. From an object-oriented point of view, a data object is an instance of a data
class. Specific data classes carry the semantic within a logical node.

Data attribute instance DAI

A Data attribute defines the name (semantic), format, range of possible values, and
representation of values while being communicated.

Annunciation types via GOOSE

Generic Object Oriented Substation Event
A GOOSE report enables high speed trip signals to be issued with a high probability of delivery.
The following types of information can be configured via GOOSE.
 External single point indication O/O

 External single point indication I/O

 External double point indication

 External double point indication, fast

 External operational measured values

 External metered values

SIPROTEC, 7SJ66, IEC61850 MAPPING 11

C53000-G2640-C554-2, Edition 12.2017
Basics
1.2 Effects of Configuration on the Logical Nodes

1.2 Effects of Configuration on the Logical Nodes

1.2.1 Function parameters

Depending on the configuration of the function parameters the functions of the SIPROTEC are
enabled or disabled. If a function is disabled, the corresponding Logical Node is not available.

The following Logical Nodes are always available:

Logical Device Protection: LLN0, LPHD1, XCBR1,

PTRC1
Logical Device Measurement: LLN0, LPHD1, MMXU1,
MMTR1, MSQI1
Logical Device Control: LLN0, LPHD1, CALH1

12 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.2 Effects of Configuration on the Logical Nodes

1.2.2 Function parameters SIPROTEC 7SJ66

The following table shows which Logical Nodes are available when setting the corresponding
function parameter.
The setting (-) implies that no corresponding LN is available.

Table 1-1 SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes

No. Function Setting Logical Nodes

103 Setting Group Change Option No effect

104 Oscillographic Fault Records Disabled -

Enabled RDRE1

112 50/51 (Charac. Phase) Disabled -

Overcurrent Protection
Definite Time PTOC6, PTOC7, PTOC1
PTOC18, PTRC2

TOC IEC PTOC6, PTOC7, PTOC1

PTOC18, PTRC2

TOC ANSI PTOC6, PTOC7, PTOC1

PTOC18, PTRC2

User Defined PU PTOC6, PTOC7, PTOC1

PTOC18, PTRC2

Userdef. Reset PTOC6, PTOC7,

PTOC1, PTOC18,
PTRC2

113 50N/51N (Charac. Ground) Disabled -

Overcurrent Protection
Definite Time PTOC8, PTOC9,
PTOC2, PTRC2

TOC IEC PTOC8, PTOC9,

PTOC2, PTRC2

TOC ANSI PTOC8, PTOC9,

PTOC2, PTRC2

User Defined PU PTOC8, PTOC9,

PTOC2, PTRC2

Userdef. Reset PTOC8, PTOC9,

PTOC2, PTRC2

SIPROTEC, 7SJ66, IEC61850 MAPPING 13

C53000-G2640-C554-2, Edition 12.2017
Basics
1.2 Effects of Configuration on the Logical Nodes

Table 1-1 SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No. Function Setting Logical Nodes

115 67, 67-TOC Disabled -

Directional Overcurrent Protection
Definite Time PTOC10, PTOC11,
PTOC19, PTOC3,
PTRC3

TOC IEC PTOC10, PTOC11,

PTOC19, PTOC3,
PTRC3

TOC ANSI PTOC10, PTOC11,

PTOC19, PTOC3,
PTRC3

User Defined PU PTOC10, PTOC11,

PTOC19, PTOC3,
PTRC3

Userdef. Reset PTOC10, PTOC11,

PTOC19, PTOC3,
PTRC3

116 67N, 67N-TOC Disabled -

Directional Overcurrent Protection
Definite Time PTOC12, PTOC13,
PTOC20, PTOC4,
PTRC3

TOC IEC PTOC12, PTOC13,

PTOC20, PTOC4,
PTRC3

TOC ANSI PTOC12, PTOC13,

PTOC20, PTOC4,
PTRC3

User Defined PU PTOC12, PTOC13,

PTOC20, PTOC4,
PTRC3

Userdef. Reset PTOC12, PTOC13,

PTOC20, PTOC4,
PTRC3

117 Cold Load Pickup No effect

122 2nd Harmonic Inrush Restraint No effect

14 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.2 Effects of Configuration on the Logical Nodes

Table 1-1 SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No. Function Setting Logical Nodes

127 50 1Ph Disabled -

Single Phase Overcurrent Protection
Enabled PTOC16, PTOC17

130 (sens.) Ground fault dir. characteristic cos  / sin  see Parameter 131

V0/I0  mea. see Parameter 131

131 (sensitive) Ground fault Disabled -

and
(sens.) Ground fault dir. characteristic = Definite Time PHIZ1, PSDE1, PSDE2
cos  / sin 
TOC IEC PHIZ1, PSDE2, PSDE3

TOC IANSI PHIZ1, PSDE2, PSDE3

User Defined PU PHIZ1, PSDE2, PSDE3

Log. inverse 1 PHIZ1, PSDE2, PSDE3

Log. inverse 2 PHIZ1, PSDE2, PSDE3

131 (sensitive) Ground fault Disabled -

and
(sens.) Ground fault dir. characteristic = Definite Time PHIZ1, PSDE1, PSDE2
V0/I0  mea.
User Defined PU PHIZ1, PSDE1, PSDE2

133 Intermittent earth fault protection No effect

134 Dir. Intermittent earth fault protection No effect

135 Admittance Earth Fault Protection Disable -

Enable PSDE4, PSDE5, PSDE6,

PSDE7

140 46 Negative Sequence Protection Disabled -

TOC ANSI PTOC14, PTOC15,

PTOC5

TOC IEC PTOC14, PTOC15,

PTOC5

Definite Time PTOC14, PTOC15

SIPROTEC, 7SJ66, IEC61850 MAPPING 15

C53000-G2640-C554-2, Edition 12.2017
Basics
1.2 Effects of Configuration on the Logical Nodes

Table 1-1 SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No. Function Setting Logical Nodes

141 48 Startup Supervision of Motors Disabled -

Enabled PMSS1

142 49 Thermal Overload Protection Disabled -

No ambient temp PTTR1

With amb. temp. PTTR1

143 66 Startup Counter for Motors Disabled -

Enabled PMRI1

144 Load Jam Protection Disabled -

Enabled PMLJ1

150 27, 59 Under/Overvoltage Protection Disabled -

Enabled PTUV1, PTUV2,

PTOV1, PTOV2

154 81 Over/Underfrequency Protection Disabled -

Enabled PTOF1 – PTOF4,

PTUF1 – PTUF4

155 27/Q-Protection Disabled -

Enabled PTUV7

161 25 Function group 1 Disabled -

Synchronism and Voltage Check
SYNCHROCHECK RSYN1

170 50BF Breaker Failure Protection Disabled -

Enabled RBRF1

enabled w/ 3I0> RBRF1

171 79 Auto-Reclose Function Disabled -

Enabled RREC1

172 52 Breaker Wear Monitoring No effect

16 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.2 Effects of Configuration on the Logical Nodes

Table 1-1 SIPROTEC 7SJ66 - Effects of Function parameters to the Logical Nodes (Cont.)

No. Function Setting Logical Nodes

180 Fault Locator Disabled -

Enabled RFLO1

181 Line sections for fault locator No effect

182 74TC Trip Circuit Supervision Disabled -

2 Binary Inputs DOI CirSpv, LN XCBR

LD PROT

1 Binary Input DOI CirSpv, LN XCBR

LD PROT

190 External Temperature Input No effect

191 Ext. Temperature Input Connection Type No effect

SIPROTEC, 7SJ66, IEC61850 MAPPING 17

C53000-G2640-C554-2, Edition 12.2017
Basics
1.3 Allocation of Logical Nodes to Logical Devices

1.3 Allocation of Logical Nodes to Logical Devices

All Logical Nodes (LN) are allocated to Logical Devices (LD). The following tables show this
allocation and the DOIs available for each LN.

LD PROT
The Logical Device PROT (Protection) contains the following LNs:

Table 1-2 LD PROT - Logical Nodes

LN Function DOI

LLN0 General Mod, Beh, Health, NamPlt, OpTmh

PTRC1 General device pickup Mod, Beh, Health, NamPlt, Str,Tr,FinTr

General OFF

XCBR1 52 Breaker  Mod, Beh, Health, NamPlt, Loc, OpCnt, Pos

Three-pole tripping BlkOpn, BlkCls, CBOpCap
SumSwARs1, SumSwARs2, SumSwARs3

PTOC6 50/51 (Charac. Phase) Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC7
PTOC18
PTOC1
PTRC2

PTOC8 50N/51N (Charac. Ground) Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC9
PTOC2
PRTC2

PTOC10 67, 67-TOC Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC11
PTOC19
PTOC3
PTRC3

PTOC12 67N, 67N-TOC Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC13
PTOC20
PTOC4
PRTC3

PTOC16 50 1Ph Mod, Beh, Health, NamPlt, Str, Op

PTOC17

PTUV1 27 Undervoltage Protection Mod, Beh, Health, NamPlt, Str, Op

PTUV2

PTOV1 59 Overvoltage Protection Mod, Beh, Health, NamPlt, Str, Op

PTOV2

18 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.3 Allocation of Logical Nodes to Logical Devices

Table 1-2 LD PROT - Logical Nodes (Cont.)

LN Function DOI

PTUV7 27/Q-Protection Mod, Beh, Health, NamPlt, Str, Op

PTOC14 46 Negative Sequence Protection Mod, Beh, Health, NamPlt, Str, Op

PTOC15
PTOC5

PMSS1 48 Startup Supervision of Motors Mod, Beh, Health, NamPlt, Str, Op

PMRI1 66 Startup Counter for Motors Mod, Beh, Health, NamPlt, Op, StrInhTmm

PMLJ1 Load Jam Protection Mod, Beh, Health, NamPlt, Str, Op, LDJamAlm,
ChgSet

PTUF1 81 Underfrequency Protection Mod, Beh, Health, NamPlt, Str, Op, BlkV
PTUF2
PTUF3
PTUF4

PTOF1 81 Overfrequency Protection Mod, Beh, Health, NamPlt, Str, Op, BlkV
PTOF2
PTOF3
PTOF4

PTTR1 49 Thermal Overload Protection Mod, Beh, Health, NamPlt, Str, Op, AlmThm

PSDE1 (sensitive) Ground fault Mod, Beh, Health, NamPlt, Str, Op

PSDE2
PSDE3

PSDE4 Admittance Earth Fault Protection Mod, Beh, Health, NamPlt, Str, Op
PSDE5
PSDE6
PSDE7

PHIZ1 (sensitive) Ground fault Mod, Beh, Health, NamPlt, Str, Op

RREC1 79 Auto-Reclose Function Mod, Beh, Health, NamPlt, Op, AutoRecSt

RFLO1 Fault Locator Mod, Beh, Health, NamPlt, FltZ, FltDiskm, FltDisPrc

RBRF1 50BF Breaker Failure Protection Mod, Beh, Health, NamPlt, Str, OpEx, OpIn

LPHD1 Device PhyNam, PhyHealth, Proxy

SIPROTEC, 7SJ66, IEC61850 MAPPING 19

C53000-G2640-C554-2, Edition 12.2017
Basics
1.3 Allocation of Logical Nodes to Logical Devices

LD MEAS
The Logical Device MEAS (Measurement) contains the following LNs:

Table 1-3 LD MEAS - Logical Nodes

LN Function DOIs

LLN0 General Mod, Beh, Health, NamPlt

MMXU1 Operational measured values Mod, Beh, Health, NamPlt,

TotW, TotVAr, TotVA, TotPF, Hz, PPV, PhV, A

MMTR1 Power Metering Mod, Beh, Health, NamPlt,

SupWh, SupVArh, DmdWh, DmdVArh

MSQI1 Measured values, symmetrical Mod, Beh, Health, NamPlt, SeqA, SeqV
components

LPHD1 Device PhyNam, PhyHealth, Proxy

LD DR
The Logical Device DR (Disturbance Recorder) contains the following LNs:

Table 1-4 LD DR - Logical Nodes

LN Function DOIs

LLN0 General Mod, Beh, Health, NamPlt

RDRE1 Oscillographic Fault Records Mod, Beh, Health, NamPlt, RcdMade, RcdStr
FltNum, GriFltNum

LPHD1 Device PhyNam, PhyHealth, Proxy

20 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.3 Allocation of Logical Nodes to Logical Devices

LD CTRL
The Logical Device CTRL (Control) contains the following LNs:

Table 1-5 LD CTRL - Logical Nodes

LN Function DOIs

LLN0 General Mod, Beh, Health, NamPlt, LEDRs, Loc

RSYN1 25 Function group 1 Mod, Beh, Health, NamPlt, 

Rel, VInd, AngInd, HzInd, SynPrg, 
DifVClc, DifHzClc, DifAngClc

CALH1 Error with a summary alarm and Mod, Beh, Health, NamPlt, GrAlm, GrWrn, 
Alarm summary event ErrBoard1, ErrBoard2, ErrBoard3, ErrBoard4,
ErrBoard5, ErrBoard6, ErrBoard7

LPHD1 Device PhyNam, PhyHealth, Proxy, CtlNum, DevStr

LD EXT
The Logical Device EXT (Extended) contains the following LNs:

Table 1-6 LD EXT - Logical Nodes

LN Function DOIs

LLN0 General Mod, Beh, Health, NamPlt, LEDRs, Loc

LPHD1 Device PhyNam, PhyHealth, Proxy, CtlNum

The Logical Nodes of the switching (and userdefined) objects will be created by DIGSI during
the parameterization of your SIPROTEC device.
MICS, Model Implementation Conformance Statement, shows the assignment of the DOIs;
you can use DIGSI to print the MICS.

SIPROTEC, 7SJ66, IEC61850 MAPPING 21

C53000-G2640-C554-2, Edition 12.2017
Basics
1.4 Logical Node LLN0

1.4 Logical Node LLN0

1.4.1 Logical Device PROT

LLN0.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 0 1 1 1 1

Test mode (Test mode) x 0 0 1 1

Stop data transmission (DataStop) x 0 1 0 1

LLN0.Mod.stVal 5 1 2 3 4

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Beh

No. Information

51 Device is Operational and Protecting (Device OK) 0 1 1 1 1

Test mode (Test mode) x 0 0 1 1

Stop data transmission (DataStop) x 0 1 0 1

LLN0.Beh.stVal 5 1 2 3 4

device annunciation / setting: 1 - ON / TRUE IEC Status Beh.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

LLN0.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

22 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.4 Logical Node LLN0

LLN0.OpTmh

No. Information Value

1020 Counter of operating hours (Op.Hours=) LLN0.OpTmh.stVal Operating hours (Absolute value)

SIPROTEC, 7SJ66, IEC61850 MAPPING 23

C53000-G2640-C554-2, Edition 12.2017
Basics
1.4 Logical Node LLN0

1.4.2 Logical Devices MEAS, DR and EXT

LLN0.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 0 1 1 1 1

Test mode (Test mode) x 1 1 0 0

Stop data transmission (DataStop) x 1 0 1 0

LLN0.Mod.stVal 5 4 3 2 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Beh

No. Information

51 Device is Operational and Protecting (Device OK) 0 1 1 1 1

Test mode (Test mode) x 0 0 1 1

Stop data transmission (DataStop) x 0 1 0 1

LLN0.Beh.stVal 5 1 2 3 4

device annunciation / setting: 1 - ON / TRUE IEC Status Beh.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

LLN0.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

24 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.4 Logical Node LLN0

1.4.3 Logical Device CTRL

LLN0.Mod

No. Information

55 Reset Device (Reset Device) 1 1 1 1 1

51 Device is Operational and Protecting (Device OK) 1 1 1 1 0

Test mode (Test mode) 1 1 0 0 0

Stop data transmission (DataStop) 1 0 1 0 0

LLN0.Mod.stVal 4 3 2 1 5

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Beh

No. Information

55 Reset Device (Reset Device) 1 1 1 1 1

51 Device is Operational and Protecting (Device OK) 1 1 1 1 0

Test mode (Test mode) 1 1 0 0 0

Stop data transmission (DataStop) 1 0 1 0 0

LLN0.Beh.stVal 4 3 2 1 5

device annunciation / setting: 1 - ON / TRUE IEC Status Beh.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

LLN0.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

LLN0.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 25

C53000-G2640-C554-2, Edition 12.2017
Basics
1.4 Logical Node LLN0

LLN0.OpTmh

No. Information Value

1020 Counter of operating hours (Op.Hours=) LLN0.OpTmh.stVal Operating hours (Absolute value)

26 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Basics

1.5 DOI Behavior

1.5 DOI Behavior

1.5.1 Logical Device PROT

For the Logical Nodes of the PROT Logical Device, LNx.Beh.stVal is formed from
LNx.Mod.stVal of the Logical Node and the status of the following device messages:
 Test mode (Test mode),

 Stop data transmission and

 At Least 1 Protection Funct. is Active.

No. Information

Test mode (Test mode) x 0 1 0 1 x

Stop data transmission (DataStop) x 0 0 1 1 x

51 Device is Operational and Protecting (Device OK) x 1 1 1 1 0

LNx .Mod.stVal 5 1 1 1 1 x

LNx.Beh.stVal 5 1 3 2 4 5

device annunciation / setting: 1 - ON / TRUE IEC Status stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING 27

C53000-G2640-C554-2, Edition 12.2017
Basics
1.5 DOI Behavior

1.5.2 Logical Devices MEAS, CTRL, DR and EXT

For the Logical Nodes of the MEAS, CTRL, DR and EXT Logical Devices, LNx.Beh.stVal is
formed from LNx.Mod.stVal of the Logical Node and the status of the following device
messages:
 Test mode (Test mode),

 Stop data transmission.

No. Information

Test mode (Test mode) x 0 1 0 1 0 1

Stop data transmission (DataStop) x 0 0 1 1 x x

LNx .Mod.stVal 5 1 1 1 1 2 2

LNx.Beh.stVal 5 1 3 2 4 2 4

device annunciation / setting: 1 - ON / TRUE IEC Status stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

28 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-G2640-C554-2, Edition 12.2017
 Mapping

Mapping 2

Contents
This chapter shows the mapping of the information relevant to the device on the Logical Node of
protocol IEC61850. It is structured according to function. In Chapter 1 you can find what
consequences non-configured functions have on the Logical Nodes as well as general
information about IEC 61850 mapping of information.

2.1 Device (LPHD1, CALH1) 30

2.2 Oscillographic Fault Records (RDRE1) 34

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2) 36

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3) 48

2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17) 63

2.6 Voltage Protection 27, 59 (PTUVx, PTOVx) 66

2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5) 72

2.8 Motor Protection (PMSS1, PMRI1) 76

2.9 Load Jam Protection (PMLJ1) 79

2.10 Frequency protection 81 O/U (PTUFx, PTOFx) 81

2.11 QV Protection 27/Q (PTUV9) 97

2.12 Thermal overload protection (PTTR1) 98

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx) 100

2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7) 110

2.15 Automatic Reclosing System 79 (RREC1) 116

2.16 Fault Locator (RFLO1) 117

2.17 Circuit breaker failure protection 50BF(RBRF1) 119

2.18 Synchronism and Voltage Check 25 (RSYNx) 121

2.19 Three-pole tripping 52 Breaker (XCBR1) 124

2.20 Tripping Logic of the Entire Device (PTRC1) 128

2.21 Measurement (MMXU1, MSQI1, MMTR1) 130

SIPROTEC, 7SJ66, IEC61850 MAPPING 29

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.1 Device (LPHD1, CALH1)

2.1 Device (LPHD1, CALH1)

LPHD1.DevStr

No. Information

56 Initial Start of Device (Initial Start) 0 0 1 1

67 Resume (Resume) 0 1 0 1

LPHD1.DevStr.stVal T 2 1 T

device annunciation: 1 - ON IEC Status DevStr.stVal: 1 - Initial Start

0 - OFF 2 - Resume
T - toggel between 1 and 2

LPHD1.Proxy

No. Information

55 Reset Device (Reset Device) 0 1

LPHD1.Proxy.stVal 1 0

device annunciation: 1 - ON IEC Status Proxy.stVal: 0 - DEVICE is not a PROXY

0 - OFF 1 - DEVICE is a PROXY

LPHD1.PhyHealth

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

LPHD1.PhyHealth.stVal 3 1

device annunciation: 1 - ON IEC Status PhyHealth.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

30 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.1 Device (LPHD1, CALH1)

2.1.1 Error with a summary alarm and Alarm summary event

CALH1.Mod

No. Information

56 Initial Start of Device (Initial Start) 1 0

CALH1.Mod.stVal 1 5

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

CALH1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

CALH1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

CALH1.GrAlm

No. Information

140 Error with a summary alarm (Error Sum Alarm) 1 0

CALH1.GrAlm.stVal 1 0

device annunciation: 1 - ON IEC Status GrAlm.stVal: 0 - FALSE

0 - OFF 1 - TRUE

CALH1.GrWrn

No. Information

160 Alarm Summary Event (Alarm Sum Event) 1 0

CALH1.GrWrn.stVal 1 0

device annunciation: 1 - ON IEC Status GrWrn.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 31

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.1 Device (LPHD1, CALH1)

The LN CALH1.ErrBoard1 to CALH1.ErrBoard7 are available with Firmware

CALH1.ErrBoard1

No. Information

183 Error Board 1 (Error Board 1) 1 0

CALH1.ErrBoard1.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard1.stVal: 0 - FALSE

0 - OFF 1 - TRUE

CALH1.ErrBoard2

No. Information

184 Error Board 2 (Error Board 2) 1 0

CALH1.ErrBoard2.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard2.stVal: 0 - FALSE

0 - OFF 1 - TRUE

CALH1.ErrBoard3

No. Information

185 Error Board 3 (Error Board 3) 1 0

CALH1.ErrBoard3.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard3.stVal: 0 - FALSE

0 - OFF 1 - TRUE

CALH1.ErrBoard4

No. Information

186 Error Board 4 (Error Board 4) 1 0

CALH1.ErrBoard4.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard4.stVal: 0 - FALSE

0 - OFF 1 - TRUE

32 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.1 Device (LPHD1, CALH1)

CALH1.ErrBoard5

No. Information

187 Error Board 5 (Error Board 5) 1 0

CALH1.ErrBoard5.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard5.stVal: 0 - FALSE

0 - OFF 1 - TRUE

CALH1.ErrBoard6

No. Information

188 Error Board 6 (Error Board 6) 1 0

CALH1.ErrBoard6.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard6.stVal: 0 - FALSE

0 - OFF 1 - TRUE

CALH1.ErrBoard7

No. Information

189 Error Board 7 (Error Board 7) 1 0

CALH1.ErrBoard7.stVal 1 0

device annunciation: 1 - ON IEC Status ErrBoard7.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 33

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.2 Oscillographic Fault Records (RDRE1)

2.2 Oscillographic Fault Records (RDRE1)

RDRE1.Mod

No. Information

55 Reset Device (Reset Device) x

RDRE1.Mod.stVal 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

RDRE1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

RDRE1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

RDRE1.RcdMade

No. Information

30053 Fault recording is running (Fault rec. run.) 0 1

RDRE1.RcdMade.stVal 1 0

device annunciation: 1 - ON IEC Status RcdMade.stVal: 0 - FALSE

0 - OFF 1 - TRUE
(Recording complete)

RDRE1.FltNum

No. Information Value

302 Fault Event (Fault Event) RDRE1.FltNum.stVal Present fault number

RDRE1.GriFltNum

No. Information Value

301 Power System fault (Pow.Sys.Flt.) RDRE1.GriFltNum.stVal Network fault number

34 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.2 Oscillographic Fault Records (RDRE1)

RDRE1.RcdStr

No. Information

30053 Fault recording is running (Fault rec. run.) 0 1

RDRE1.RcdStr.stVal 0 1

device annunciation: 1 - ON IEC Status RcdStr.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 35

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3.1 Overcurrent Protection 50, 51 PH (PTOC6, PTOC7, PTOC18, PTOC1)

PTOC6.Mod

No. Information

1751 50/51 O/C switched OFF (50/51 PH OFF) 1 x 0

50-1 PICKUP (P1204) =  x 1 0

PTOC6.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC6.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC6.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC6.Str

No. Information

1810 50-1 picked up (50-1 picked up) 0 1

PTOC6.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC6.Op

No. Information

1815 50-1 TRIP (50-1 TRIP) 0 1

PTOC6.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

36 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC6.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC6.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC7.Mod

No. Information

1751 50/51 O/C switched OFF (50/51 PH OFF) 1 x 0

50-2 PICKUP (P1202) =  x 1 0

PTOC7.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC7.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC7.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC7.Str

No. Information

1800 50-2 picked up (50-2 picked up) 0 1

PTOC7.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 37

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC7.Op

No. Information

1805 50-2 TRIP (50-2 TRIP) 0 1

PTOC7.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC7.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC7.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC18.Mod

No. Information

1751 50/51 O/C switched OFF (50/51 PH OFF) 1 x 0

50-3 PICKUP(P1217) =  x 1 0

PTOC18.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC18.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC18.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

38 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC18.Str

No. Information

1767 50-3 picked up (50-3 picked up) 0 1

PTOC18.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC18.Op

No. Information

1769 50-3 TRIP (50-3 TRIP) 0 1

PTOC18.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC18.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC18.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC1.Mod

No. Information

1751 50/51 O/C switched OFF (50/51 PH OFF) 1 0

PTOC1.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING 39

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC1.Str

No. Information

1820 51 picked up (51 picked up) 0 1

PTOC1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC1.Op

No. Information

1825 51 TRIP (51 TRIP) 0 1

PTOC1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC1.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC1.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

40 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3.2 Overcurrent Protection 50N, 51N (PTOC8, PTOC9, PTOC2)

PTOC8.Mod

No. Information

7156 50N/51N is OFF (50N/51N OFF) 1 x 0

50N-1 PICKUP (P1304) =  x 1 0

PTOC8.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC8.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC8.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC8.Str

No. Information

1834 50N-1 picked up (50N-1 picked up) 0 1

PTOC8.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC8.Op

No. Information

1836 50N-1 TRIP (50N-1 TRIP) 0 1

PTOC8.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 41

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC8.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC8.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC9.Mod

No. Information

7156 50N/51N is OFF (50N/51N OFF) 1 x 0

50N-2 PICKUP (P1302) =  x 1 0

PTOC9.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC9.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC9.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC9.Str

No. Information

1831 50N-2 picked up (50N-2 picked up) 0 1

PTOC9.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

42 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC9.Op

No. Information

1833 50N-2 TRIP (50N-2 TRIP) 0 1

PTOC9.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC9.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC9.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC2.Mod

No. Information

1756 50N/51N is OFF (50N/51N OFF) 1 0

PTOC2.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 43

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTOC2.Str

No. Information

1837 51N picked up (51N picked up) 0 1

PTOC2.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC2.Op

No. Information

1839 51N TRIP (51N TRIP) 0 1

PTOC2.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC2.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC2.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

44 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

2.3.3 Overcurrent Protection 50N, 51N (PTRC2)

PTRC2.Mod

No. Information

1751 50/51 O/C switched OFF (50/51 PH OFF) and 1 0

1756 50N/51N is OFF (50N/51N OFF)

PTRC2.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTRC2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTRC2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTRC2.Str

No. Information

1761 50(N)/51(N) O/C PICKUP (50(N)/51(N) PU) 0 1

PTRC2.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTRC2.Str.dirGeneral

No. Information

PTRC2.Str.dirGeneral 0

device annunciation: IEC Status Str.dirGeneral: 0 - UNKNOWN

SIPROTEC, 7SJ66, IEC61850 MAPPING 45

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTRC2.Str.phsA

No. Information

1762 50/51 Phase A picked up (50/51 Ph A PU) 0 1

PTRC2.Str.phsA 0 1

device annunciation: 1 - ON IEC Status Str.phsA: 0 - FALSE

0 - OFF 1 - TRUE

PTRC2.Str.dirPhsA

No. Information

PTRC2.Str.dirPhsA 0

device annunciation: IEC Status Str.dirPhsA: 0 - UNKNOWN

PTRC2.Str.phsB

No. Information

1763 50/51 Phase B picked up (50/51 Ph B PU) 0 1

PTRC2.Str.phsB 0 1

device annunciation: 1 - ON IEC Status Str.phsB: 0 - FALSE

0 - OFF 1 - TRUE

PTRC2.Str.dirPhsB

No. Information

PTRC2.Str.dirPhsB 0

device annunciation: IEC Status Str.dirPhsB: 0 - UNKNOWN

PTRC2.Str.phsC

No. Information

1764 50/51 Phase C picked up (50/51 Ph C PU) 0 1

PTRC2.Str.phsC 0 1

device annunciation: 1 - ON IEC Status Str.phsC: 0 - FALSE

0 - OFF 1 - TRUE

46 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)

PTRC2.Str.dirPhsC

No. Information

PTRC2.Str.dirPhsC 0

device annunciation: IEC Status Str.dirPhsC: 0 - UNKNOWN

PTRC2.Str.neut

No. Information

1765 50N/51N picked up (50N/51NPickedup) 0 1

PTRC2.Str.neut 0 1

device annunciation: 1 - ON IEC Status Str.neut: 0 - FALSE

0 - OFF 1 - TRUE

PTRC2.Str.dirNeut

No. Information

PTRC2.Str.dirNeut 0

device annunciation: IEC Status Str.dirPhsC: 0 - UNKNOWN

PTRC2.Op

No. Information

1791 50(N)/51(N) TRIP (50(N)/51(N)TRIP) 0 1

PTRC2.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 47

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4.1 Directional Overcurrent Protection 67 (PTOC10, PTOC11, PTOC19,

PTOC3)

PTOC10.Mod

No. Information

2651 67/67-TOC switched OFF (67/67-TOC OFF) 1 x 0

67-1 PICKUP (P1504) =  x 1 0

PTOC10.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC10.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC10.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC10.Str

No. Information

2660 67-1 picked up (67-1 picked up) 0 1

PTOC10.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

48 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC10.Op

No. Information

2665 67-1 TRIP (67-1 TRIP) 0 1

PTOC10.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC10.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC10.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC11.Mod

No. Information

2651 67/67-TOC switched OFF (67/67-TOC OFF) 1 x 0

67-2 PICKUP (P1502) =  x 1 0

PTOC11.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC11.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC11.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 49

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC11.Str

No. Information

2642 67-2 picked up (67-2 picked up) 0 1

PTOC11.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC11.Op

No. Information

2649 67-2 TRIP (67-2 TRIP) 0 1

PTOC11.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC11.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC11.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC19.Mod

No. Information

2651 67/67-TOC switched OFF (67/67-TOC OFF) 1 x 0

67-3 PICKUP (P1528) =  x 1 0

PTOC19.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

50 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC19.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC19.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC19.Str

No. Information

2697 67-3 picked up (67-3 picked up) 0 1

PTOC19.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC19.Op

No. Information

2678 67-3 TRIP (67-3 TRIP) 0 1

PTOC19.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC19.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC19.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 51

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC3.Mod

No. Information

2651 67/67-TOC switched OFF (67/67-TOC OFF) 1 0

PTOC3.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC3.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC3.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC3.Str

No. Information

2670 67-TOC picked up (67-TOC picked up) 0 1

PTOC3.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC3.Op

No. Information

2675 67-TOC TRIP (67-TOC TRIP) 0 1

PTOC3.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

52 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC3.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC3.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 53

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4.2 Directional Overcurrent Protection 67N (PTOC12, PTOC13,

PTOC20, PTOC4)

PTOC12.Mod

No. Information

2656 67N/67N-TOC switched OFF (67N OFF) 1 x 0

67N-1 PICKUP (P1604) =  x 1 0

PTOC12.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC12.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC12.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC12.Str

No. Information

2681 67N-1 picked up (67N-1 picked up) 0 1

PTOC12.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC12.Op

No. Information

2683 67N-1 TRIP (67N-1 TRIP) 0 1

PTOC12.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

54 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC12.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC12.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC13.Mod

No. Information

2656 67N/67N-TOC switched OFF (67N OFF) 1 x 0

67N-2 PICKUP (P1602) =  x 1 0

PTOC13.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC13.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC13.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC13.Str

No. Information

2646 67N-2 picked up (67N-2 picked up) 0 1

PTOC13.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 55

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC13.Op

No. Information

2679 67N-2 TRIP (67N-2 TRIP) 0 1

PTOC13.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC13.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC13.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC20.Mod

No. Information

2656 67N/67N-TOC switched OFF (67N OFF) 1 x 0

67N-3 PICKUP (P1628) =  x 1 0

PTOC20.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC20.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC20.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

56 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC20.Str

No. Information

2698 67N-3 picked up (67N-3 picked up) 0 1

PTOC20.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC20.Op

No. Information

2603 67N-3 TRIP (67N-3 TRIP) 0 1

PTOC20.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC20.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC20.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

PTOC4.Mod

No. Information

2656 67N/67N-TOC switched OFF (67N OFF) 1 x 0

M.of PU TD (P1630) =  x 1 0

PTOC4.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING 57

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTOC4.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC4.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC4.Str

No. Information

2684 67N-TOC picked up (67N-TOCPickedup) 0 1

PTOC4.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC4.Op

No. Information

2686 67N-TOC TRIP (67N-TOC TRIP) 0 1

PTOC4.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC4.ChgSet

No. Information

1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1

PTOC4.ChgSet.stVal 0 1

device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE

58 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

2.4.3 Directional Overcurrent Protection 67N (PTRC3)

PTRC3.Mod

No. Information

67/67-TOC switched OFF (67/67-TOC OFF) (I 2651) and 1 0

67N/67N-TOC switched OFF (67N OFF) (I 2656)

PTRC3.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTRC3.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTRC3.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTRC3.Str

No. Information

2691 67/67N picked up (67/67N pickedup) 0 1

PTRC3.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 59

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTRC3.Str.dirGeneral

No. Information

2691 67/67N picked up (67/67N picked up) 0 1 1 1 1

Phase A forward (Phase A forward) (I 2628) or x 0 1 0 1

Phase B forward (Phase B forward) (I 2629) or
Phase C forward (Phase C forward) (I 2630) or
Ground forward (Ground forward) (I 2635)

Phase A reverse (Phase A reverse) (I 2632) or x 0 0 1 1

Phase B reverse (Phase B reverse) (I 2633) or
Phase C reverse (Phase C reverse) (I 2634) or
Ground reverse (Ground reverse) (I 2636)

PTRC3.Str.dirGeneral 0 0 1 2 3

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
2 - BACKWARD
3 - BOTH

PTRC3.Str.phsA

No. Information

2692 67/67-TOC Phase A picked up (67 A picked up) 0 1

PTRC3.Str.phsA 0 1

device annunciation: 1 - ON IEC Status Str.phsA: 0 - FALSE

0 - OFF 1 - TRUE

PTRC3.Str.dirPhsA

No. Information

2692 67/67-TOC Phase A picked up (67 A picked up) 0 1 1 1 1

2628 Phase A forward (Phase A forward) x 0 1 0 1

2632 Phase A reverse (Phase A reverse) x 0 0 1 1

PTRC3.Str.dirPhsA 0 0 1 2 3

device annunciation: 1 - ON IEC Status Str.dirPhsA: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

60 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTRC3.Str.phsB

No. Information

2693 67/67-TOC Phase B picked up (67 B picked up) 0 1

PTRC3.Str.phsB 0 1

device annunciation: 1 - ON IEC Status Str.phsB: 0 - FALSE

0 - OFF 1 - TRUE

PTRC3.Str.dirPhsB

No. Information

2693 67/67-TOC Phase B picked up (67 B picked up) 0 1 1 1 1

2629 Phase B forward (Phase B forward) x 0 1 0 1

2633 Phase B reverse (Phase B reverse) x 0 0 1 1

PTRC3.Str.dirPhsB 0 0 1 2 3

device annunciation: 1 - ON IEC Status Str.dirPhsB: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

PTRC3.Str.phsC

No. Information

2694 67/67-TOC Phase C picked up (67 C picked up) 0 1

PTRC3.Str.phsC 0 1

device annunciation: 1 - ON IEC Status Str.phsC: 0 - FALSE

0 - OFF 1 - TRUE

PTRC3.Str.dirPhsC

No. Information

2694 67/67-TOC Phase C picked up (67 C picked up) 0 1 1 1 1

2630 Phase C forward (Phase C forward) x 0 1 0 1

2634 Phase C reverse (Phase C reverse) x 0 0 1 1

PTRC3.Str.dirPhsC 0 0 1 2 3

device annunciation: 1 - ON IEC Status Str.dirPhsC: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

SIPROTEC, 7SJ66, IEC61850 MAPPING 61

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)

PTRC3.Str.neut

No. Information

2695 67N/67N-TOC picked up (67N picked up) 0 1

PTRC3.Str.neut 0 1

device annunciation: 1 - ON IEC Status Str.neut: 0 - FALSE

0 - OFF 1 - TRUE

PTRC3.Str.dirNeut

No. Information

2695 67N/67N-TOC picked up (67N picked up) 0 1 1 1 1

2635 Ground forward (Ground forward) x 0 1 0 1

2636 Ground reverse (Ground reverse) x 0 0 1 1

PTRC3.Str.dirNeut 0 0 1 2 3

device annunciation: 1 - ON IEC Status Str.dirPhsC: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

PTRC3.Op

No. Information

2696 67/67N TRIP (67/67N TRIP) 0 1

PTRC3.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

62 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

PTOC16.Mod

No. Information

5961 50 1Ph is OFF (50 1Ph OFF) 1 x 0

50 1Ph-1 PICKUP (P2705) =  x 1 0

PTOC16.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC16.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC16.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC16.Str

No. Information

5974 50 1Ph-1 picked up (50 1Ph-1 PU) 0 1

PTOC16.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC16.Op

No. Information

5975 50 1Ph-1 TRIP (50 1Ph-1 TRIP) 0 1

PTOC16.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 63

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

PTOC17.Mod

No. Information

5961 50 1Ph is OFF (50 1Ph OFF) 1 x 0

50 1Ph-2 PICKUP (P2703) =  x 1 0

PTOC17.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC17.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC17.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

64 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)

PTOC17.Str

No. Information

5977 50 1Ph-2 picked up (50 1Ph-2 PU) 0 1

PTOC17.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC17.Op

No. Information

5979 50 1Ph-2 TRIP (50 1Ph-2 TRIP) 0 1

PTOC17.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 65

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.1 Undervoltage Protection 27 (PTUV1)

PTUV1.Mod

No. Information

6530 27 Undervoltage protection switched OFF (27 OFF) 1 0

PTUV1.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUV1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUV1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

66 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

PTUV1.Str

No. Information

6533 27-1 Undervoltage picked up (27-1 picked up) 0 x 1

6534 27-1 Undervoltage PICKUP w/curr. superv (27-1 PU CS) 0 1 x

PTUV1.Str.general 0 1 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE
x - irrelevant

PTUV1.Op

No. Information

6539 27-1 Undervoltage TRIP (27-1 TRIP) 0 1

PTUV1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 67

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.2 Undervoltage Protection 27 (PTUV2)

PTUV2.Mod

No. Information

6530 27 Undervoltage protection switched OFF (27 OFF) 1 0

PTUV2.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUV2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUV2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

68 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

PTUV2.Str

No. Information

6537 27-2 Undervoltage picked up (27-2 picked up) 0 x 1

6538 27-2 Undervoltage PICKUP w/curr. superv (27-2 PU CS) 0 1 x

PTUV2.Str.general 0 1 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE
X - irrelevant

PTUV2.Op

No. Information

6540 27-2 Undervoltage TRIP (27-2 TRIP) 0 1

PTUV2.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 69

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.3 Overvoltage Protection 59 (PTOV1)

PTOV1.Mod

No. Information

6565 59-Overvoltage protection switched OFF (59 OFF) 1 0

PTOV1.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOV1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOV1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOV1.Str

No. Information

6568 59 picked up (59-1 picked up) 0 1

PTOV1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOV1.Op

No. Information

6570 59 TRIP (59-1 TRIP) 0 1

PTOV1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

70 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.6 Voltage Protection 27, 59 (PTUVx, PTOVx)

2.6.4 Overvoltage Protection 59 (PTOV2)

PTOV2.Mod

No. Information

6565 59-Overvoltage protection switched OFF (59 OFF) 1 0

PTOV2.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOV2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOV2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOV2.Str

No. Information

6571 59-2 Overvoltage V>> picked up (59-2 picked up) 0 1

PTOV2.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOV2.Op

No. Information

6573 59-2 Overvoltage V>> TRIP (59-2 TRIP) 0 1

PTOV2.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 71

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC14.Mod

No. Information

5151 46 switched OFF (46 OFF) 1 0

PTOC14.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC14.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC14.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC14.Str

No. Information

5165 46-1 picked up (46-1 picked up) 0 1

PTOC14.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC14.Op

No. Information

46-1 TRIP (46-1 TRIP) 0 1

PTOC14.Op.general 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

72 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC15.Mod

No. Information

5151 46 switched OFF (46 OFF) 1 0

PTOC15.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC15.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC15.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTOC15.Str

No. Information

5159 46-2 picked up (46-2 picked up) 0 1

PTOC15.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC15.Op

No. Information

46-2 TRIP (46-2 TRIP) 0 1

PTOC15.Op.general 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 73

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC5.Mod

No. Information

5151 46 switched OFF (46 OFF) 1 0

PTOC5.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOC5.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOC5.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

74 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)

PTOC5.Str

No. Information

5166 46-TOC picked up (46-TOC pickedup) 0 1

PTOC5.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PTOC5.Op

No. Information

46-TOC TRIP (46-TOC TRIP) 0 1

PTOC5.Op.general 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 75

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.8 Motor Protection (PMSS1, PMRI1)

2.8 Motor Protection (PMSS1, PMRI1)

2.8.1 Motor Starting Protection 48 (PMSS1)

PMSS1.Mod

No. Information

6811 Startup supervision OFF (START-SUP OFF) 1 0

PMSS1.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PMSS1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PMSS1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

76 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.8 Motor Protection (PMSS1, PMRI1)

PMSS1.Str

No. Information

6823 Startup supervision Pickup (START-SUP pu) 0 1

PMSS1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PMSS1.Op

No. Information

6821 Startup supervision TRIP (START-SUP TRIP) 0 1

PMSS1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 77

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.8 Motor Protection (PMSS1, PMRI1)

2.8.2 Motor Restart Inhibit 66 (PMRI1)

PMRI1.Mod

No. Information

4824 66 Motor start protection OFF (66 OFF)) 1 0

PMRI1.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PMRI1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PMRI1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PMRI1.Op

No. Information

4827 66 Motor start protection TRIP (66 TRIP) 0 1

PMRI1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PMRI1.StrInhTmm

No. Information Value

809 Time untill release of reclose-blocking (T reclose=) PMRI1.StrInhTmm.stVal Absolute value

78 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.9 Load Jam Protection (PMLJ1)

2.9 Load Jam Protection (PMLJ1)

Function available with Firmware

PMLJ1.Mod

No. Information

10022 Load Jam Protection is OFF (JAM PROT.OFF) 1 0

PMLJ1.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PMLJ1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PMLJ1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 79

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.9 Load Jam Protection (PMLJ1)

PMLJ1.Str

No. Information

10025 Load Jam Protection picked up (Load Jam pickup) 0 1

PMLJ1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PMLJ1.Op

No. Information

10026 Load Jam Protection TRIP (Load Jam TRIP) 0 1

PMLJ1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PMLJ1.LodJamAlm

No. Information

10024 Load Jam Protection alarm (Load Jam alarm) 0 1

PMLJ1.LodJamAlm.stVal 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

80 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.1 Frequency protection 81-1 U (PTUF1)

PTUF1.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 1

PTUF1.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUF1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 81

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF1.Str

No. Information

5232 81-1 picked up (81-1 picked up) 0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1

PTUF1.Str.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF1.Op

No. Information

5236 81-1 TRIP (81-1 TRIP) 0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1

PTUF1.Op.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF1.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1

PTUF1.BlkV.stVal 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

82 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.2 Frequency protection 81-2 U (PTUF2)

PTUF2.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 1

PTUF2.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUF2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 83

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF2.Str

No. Information

5233 81-2 picked up (81-2 picked up) 0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 0 1

PTUF2.Str.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF2.Op

No. Information

5237 81-2 TRIP (81-2 TRIP) 0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 0 1

PTUF2.Op.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF2.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 0 1

PTUF2.BlkV.stVal 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

84 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.3 Frequency protection 81-3 U (PTUF3)

PTUF3.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 1

PTUF3.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF3.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUF3.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 85

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF3.Str

No. Information

5234 81-3 picked up (81-3 picked up) 0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 0 1

PTUF3.Str.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF3.Op

No. Information

5238 81-3 TRIP (81-3 TRIP) 0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 0 1

PTUF3.Op.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF3.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 0 1

PTUF3.BlkV.stVal 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

86 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.4 Frequency protection 81-4 U (PTUF4)

PTUF4.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 1

PTUF4.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUF4.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUF4.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 87

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTUF4.Str

No. Information

5235 81-4 picked up (81-4 picked up) 0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 0 1

PTUF4.Str.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF4.Op

No. Information

5239 81-4 TRIP (81-4 TRIP) 0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 0 1

PTUF4.Op.general 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTUF4.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 0 1

PTUF4.BlkV.stVal 0 0 0 1

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

88 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.5 Frequency protection 81-1 O (PTOF1)

PTOF1.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-1 PICKUP (P5403/5404)  Rated Frequency (P214) 1 x 0

PTOF1.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOF1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 89

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF1.Str

No. Information

5232 81-1 picked up (81-1 picked up) 0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1

PTOF1.Str.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF1.Op

No. Information

5236 81-1 TRIP (81-1 TRIP) 0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1

PTOF1.Op.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF1.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1

PTOF1.BlkV.stVal 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

90 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.6 Frequency protection 81-2 O (PTOF2)

PTOF2.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-2 PICKUP (P5406/5407)  Rated Frequency (P214) 1 x 0

PTOF2.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOF2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 91

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF2.Str

No. Information

5233 81-2 picked up (81-2 picked up) 0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 0 1

PTOF2.Str.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF2.Op

No. Information

5237 81-2 TRIP (81-2 TRIP) 0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 0 1

PTOF2.Op.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF2.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-2 PICKUP (P5406/5407) < Rated Frequency (P214) 0 1 0 1

PTOF2.BlkV.stVal 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

92 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.7 Frequency protection 81-3 O (PTOF3)

PTOF3.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-3 PICKUP (P5409/5410)  Rated Frequency (P214) 1 x 0

PTOF1.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF3.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOF3.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 93

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF3.Str

No. Information

5234 81-3 picked up (81-3 picked up) 0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 0 1

PTOF3.Str.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF3.Op

No. Information

5238 81-3 TRIP (81-3 TRIP) 0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 0 1

PTOF3.Op.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF3.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-3 PICKUP (P5409/5410) < Rated Frequency (P214) 0 1 0 1

PTOF3.BlkV.stVal 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

94 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

2.10.8 Frequency protection 81-4 O (PTOF4)

PTOF4.Mod

No. Information

5211 81 OFF (81 OFF) x 1 0

81-4 PICKUP (P5412/5413)  Rated Frequency (P214) 1 x 0

PTOF4.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTOF4.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTOF4.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 95

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.10 Frequency protection 81 O/U (PTUFx, PTOFx)

PTOF4.Str

No. Information

5235 81-4 picked up (81-4 picked up) 0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 0 1

PTOF4.Str.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF4.Op

No. Information

5239 81-4 TRIP (81-4 TRIP) 0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 0 1

PTOF4.Op.general 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

PTOF4.BlkV

No. Information

5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1

81-4 PICKUP (P5412/5413) < Rated Frequency (P214) 0 1 0 1

PTOF4.BlkV.stVal 0 0 1 0

device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE

0 - OFF / FALSE 1 - TRUE

96 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.11 QV Protection 27/Q (PTUV9)

2.11 QV Protection 27/Q (PTUV9)

PTUV9.Mod

No. Information

6411 27/Q -Protection off (27/Q OFF) 0 1

PTUV9.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTUV9.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTUV9.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTUV9.Str

No. Information

6423 27/Q-Protection PICKUP (27/Q PICKUP) 0 1

PTUV9.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE
x - irrelevant

PTUV9.Op

No. Information

6421 27/Q -Protection Gen TRIP (27/Q Gen TRIP) 0 1 0 1

6422 27/Q -Protection Gen TRIP (27/Q Gen TRIP) 0 0 1 1

PTUV9.Op.general 0 1 1 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 97

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.12 Thermal overload protection (PTTR1)

2.12 Thermal overload protection (PTTR1)

PTTR1.Mod

No. Information

1511 49 Overload Protection is OFF (49 O / L OFF) 1 0

PTTR1.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTTR1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTTR1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTTR1.Str

No. Information

1517 49 Winding Overload (49 Winding O/L) 0 1

PTTR1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

98 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.12 Thermal overload protection (PTTR1)

PTTR1.Op

No. Information

1521 49 Thermal Overload TRIP (49 Th O/L TRIP) 0 1

PTTR1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PTTR1.AlmThm

No. Information

1516 49 Overload Alarm! Near Thermal Trip (49 O/L  Alarm) 0 1

PTTR1.AlmThm.general 0 1

device annunciation: 1 - ON IEC Status AlmThm.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 99

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13.1 Ground Fault Protection 64 (PHIZ1)

PHIZ1.Mod

No. Information

1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 0

PHIZ1.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PHIZ1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PHIZ1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PHIZ1.Str

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 1

PHIZ1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

100 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirGeneral

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x 0 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x 0 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x 0 0 0 0 1

PHIZ1.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PHIZ1.Str.phsA

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1

1272 Sensitive Ground fault picked up in Ph A (Sens. Gnd Ph A) x 0 1 1 1 1

PHIZ1.Str.phsA 0 0 1 1 1 1

device annunciation: 1 - ON IEC Status Str.phsA: 0 -FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 101

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirPhsA

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1

1272 Sensitive Ground fault picked up in Ph A (Sens. Gnd Ph A) x 0 1 1 1 1

PHIZ1.Str.dirPhsA 0 0 1 2 0 0

device annunciation: 1 - ON IEC Status Str.dirPhsA: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

PHIZ1.Str.phsB

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1

1273 Sensitive Ground fault picked up in Ph B (Sens. Gnd Ph B) x 0 1 1 1 1

PHIZ1.Str.phsB 0 0 1 1 1 1

device annunciation: 1 - ON IEC Status Str.phsB: 0 -FALSE

0 - OFF 1 - TRUE

102 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirPhsB

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1

1273 Sensitive Ground fault picked up in Ph B (Sens. Gnd Ph B) x 0 1 1 1 1

PHIZ1.Str.dirPhsB 0 0 1 2 0 0

device annunciation: 1 - ON IEC Status Str.dirPhsB: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

PHIZ1.Str.phsC

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1

1274 Sensitive Ground fault picked up in Ph C (Sens. Gnd Ph C) x 0 1 1 1 1

PHIZ1.Str.phsC 0 0 1 1 1 1

device annunciation: 1 - ON IEC Status Str.phsC: 0 -FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 103

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PHIZ1.Str.dirPhsC

No. Information

1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1

1274 Sensitive Ground fault picked up in Ph C (Sens. Gnd Ph C) x 0 1 1 1 1

PHIZ1.Str.dirPhsC 0 0 1 2 0 0

device annunciation: 1 - ON IEC Status Str.dirPhsC: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

PHIZ1.Op

No. Information

1217 64 displacement voltage element TRIP (64 TRIP) 0 1

PHIZ1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

104 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13.2 Ground Fault Protection 50N(s) (PSDE1, PSDE2)

PSDE1.Mod

No. Information

1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 0

PSDE1.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PSDE1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PSDE1.Str

No. Information

1224 50Ns-1 Pickup (50Ns-1 Pickup) 0 1

PSDE1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 105

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PSDE1.Str.dirGeneral

No. Information

1224 50Ns-1 Pickup (50Ns-1 Pickup) 0 1 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x 0 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x 0 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x 0 0 0 0 1

PSDE1.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PSDE1.Op

No. Information

1226 50Ns-1 TRIP (50Ns-1 TRIP) 0 1

PSDE1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PSDE2.Mod

No. Information

1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 0

PSDE2.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE2.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PSDE2.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

106 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PSDE2.Str

No. Information

1221 50Ns-2 Pickup (50Ns-2 Pickup) 0 1

PSDE2.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PSDE2.Str.dirGeneral

No. Information

1221 50Ns-2 Pickup (50Ns-2 Pickup) 0 1 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x 0 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x 0 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x 0 0 0 0 1

PSDE2.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PSDE2.Op

No. Information

1223 50Ns-2 TRIP (50Ns-2 TRIP) 0 1

PSDE2.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 107

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

2.13.3 51 N(s) (PSDE3)

PSDE3.Mod

No. Information

1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 x 0

M.of PU TD (P3131) =  x 1 0

PSDE3.Mod.stVal 5 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE3.Health

No. Information

51 Device is Operational and Protecting (Device OK) x 0 1

16029 sens.grd.flt. 51Ns BLOCKED Setting Error (51Ns BLK PaErr) 1 x 0

PSDE3.Health.stVal 3 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
x - irrelevant 3 - ALARM

PSDE3.Str

No. Information

1227 51Ns picked up (51Ns Pickup) 0 1

PSDE3.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

108 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.13 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)

PSDE3.Str.dirGeneral

No. Information

1227 51Ns picked up (51Ns Pickup) 0 1 1 1 1 1

1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x 0 1 0 1 x

1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x 0 0 1 1 x

1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x 0 0 0 0 1

PSDE3.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PSDE3.Op

No. Information

1229 51Ns TRIP (51Ns TRIP) 0 1

PSDE3.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 109

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

PSDE4.Mod

No. Information

18516 Y0(G0/B0) is OFF (Y0 OFF) 1 0

PSDE4.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE4.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PSDE4.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Str.general: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PSDE4.Str

No. Information

18501 Y0(G0/B0)-1 Pickup (Y0-1 Pickup) 0 1

PSDE4.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

110 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

PSDE4.Str.dirGeneral

No. Information

18501 Y0(G0/B0)-1 Pickup (Y0-1 Pickup) 0 1 1 1 1 1

18485 Y0(G0/B0)-1 in forward direction (Y0-1 Forward) x 0 1 0 1 x

18486 Y0(G0/B0)-1 in reverse direction (Y0-1 Reverse) x 0 0 1 1 x

PSDE4.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PSDE4.Op

No. Information

18505 Y0(G0/B0)-1 TRIP (Y0-1 TRIP) 0 1

PSDE4.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PSDE5.Mod

No. Information

18516 Y0(G0/B0) is OFF (Y0 OFF) 1 0

PSDE5.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

SIPROTEC, 7SJ66, IEC61850 MAPPING 111

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

PSDE5.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PSDE5.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Str.general: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PSDE5.Str

No. Information

18502 Y0(G0/B0)-2 Pickup (Y0-2 Pickup) 0 1

PSDE5.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PSDE5.Str.dirGeneral

No. Information

18502 Y0(G0/B0)-2 Pickup (Y0-2 Pickup) 0 1 1 1 1 1

18488 Y0(G0/B0)-2 in forward direction (Y0-2 Forward) x 0 1 0 1 x

18489 Y0(G0/B0)-2 in reverse direction (Y0-2 Reverse) x 0 0 1 1 x

PSDE5.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PSDE5.Op

No. Information

18506 Y0(G0/B0)-2 TRIP (Y0-2 TRIP) 0 1

PSDE5.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

112 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

PSDE6.Mod

No. Information

18516 Y0(G0/B0) is OFF (Y0 OFF) 1 0

PSDE6.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE6.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PSDE6.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Str.general: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PSDE6.Str

No. Information

18503 Y0(G0/B0)-3 Pickup (Y0-3 Pickup) 0 1

PSDE6.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

PSDE6.Str.dirGeneral

No. Information

18503 Y0(G0/B0)-3 Pickup (Y0-3 Pickup) 0 1 1 1 1 1

18491 Y0(G0/B0)-3 in forward direction (Y0-3 Forward) x 0 1 0 1 x

18492 Y0(G0/B0)-3 in reverse direction (Y0-3 Reverse) x 0 0 1 1 x

PSDE6.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

SIPROTEC, 7SJ66, IEC61850 MAPPING 113

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

PSDE6.Op

No. Information

18507 Y0(G0/B0)-3 TRIP (Y0-3 TRIP) 0 1

PSDE6.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

PSDE7.Mod

No. Information

18516 Y0(G0/B0) is OFF (Y0 OFF) 1 0

PSDE7.Mod.stVal 5 1

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

PSDE7.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PSDE7.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Str.general: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PSDE7.Str

No. Information

18504 Y0(G0/B0)-4 Pickup (Y0-4 Pickup) 0 1

PSDE7.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

114 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.14 Admittance Earth Fault Protection (PSDE4, PSDE5, PSDE6, PSDE7)

PSDE7.Str.dirGeneral

No. Information

18504 Y0(G0/B0)-4 Pickup (Y0-4 Pickup) 0 1 1 1 1 1

18494 Y0(G0/B0)-4 in forward direction (Y0-4 Forward) x 0 1 0 1 x

18495 Y0(G0/B0)-4 in reverse direction (Y0-4 Reverse) x 0 0 1 1 x

PSDE7.Str.dirGeneral 0 0 1 2 3 0

device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD
3 - BOTH

PSDE7.Op

No. Information

18508 Y0(G0/B0)-4 TRIP (Y0-4 TRIP) 0 1

PSDE7.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 115

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.15 Automatic Reclosing System 79 (RREC1)

2.15 Automatic Reclosing System 79 (RREC1)

RREC1.Mod

No. Information

2781 79 Auto recloser is switched OFF (79 OFF) 1 0

RREC1.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

RREC1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

RREC1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

RREC1.Op

No. Information

2851 79 - Close command (79 Close) 0 1

RREC1.Op.general 0 1

device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE

RREC1.AutoRecSt

No. Information

2801 79 - in progress (79 in progress) 1 1 0 0

2862 79 - cycle successful (79 Successful) 1 0 1 0

RREC1.AutoRecSt.stVal 3 2 3 1

device annunciation: 1 - ON IEC Status AutoRecST.stVal: 1 - ready

0 - OFF 2 - in progress
3 - successful

116 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.16 Fault Locator (RFLO1)

2.16 Fault Locator (RFLO1)

RFLO1.Mod

No. Information

Fault Locator (P180) = Enabled 1 0

RFLO1.Mod.stVal 1 5

device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RFLO1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

RFLO1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

RFLO1.FltZ

No. Information Value

Absolute value of the fault RFLO1.FltZ.cVal.mag.f Measured value Absolute value

impedance
RFLO1.FltZ.units.SIUnit 30  (Ohm)

RFLO1.FltZ.units.multiplier 0 1

Angle of the fault RFLO1.FltZ.cVal.ang.f Measured value Angle in °

impedance

SIPROTEC, 7SJ66, IEC61850 MAPPING 117

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.16 Fault Locator (RFLO1)

RFLO1.FltDiskm

No. Information Value

1119 Flt Locator: Distance to fault RFLO1.FltDiskm.mag.f Measured value Absolute value
or (dist =)
1122 RFLO1.FltDiskm.units.SIUnit 2 Meter

RFLO1.FltDiskm.units.multiplie 3 Kilo
r

RFLO1.FltDisPrc

No. Information Value

1120 Flt Locator: Distance [%] to RFLO1.FltDisPrc.mag.f Measured value Absolute value
fault (d[%] =)
RFLO1.FltDisPrc.units.SIUnit 1 NONE

RFLO1.FltDisPrc.multiplier 0 1

118 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.17 Circuit breaker failure protection 50BF(RBRF1)

2.17 Circuit breaker failure protection 50BF(RBRF1)

RBRF1.Mod

No. Information

1451 Breaker failure is switched OFF (BkrFail OFF) 1 0

RBRF1.Mod.stVal 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

RBRF1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

RBRF1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

RBRF1.Str

No. Information

1456 50BF (internal) PICKUP (50BF int Pickup) 0 0 1 1

1457 50BF (external) PICKUP (50BF ext Pickup) 0 1 0 1

RBRF1.Str.general 0 1 1 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

RBRF1.OpEx

No. Information

1481 50BF (external) TRIP (50BF ext TRIP) 0 1

RBRF1.OpEx.general 0 1

device annunciation: 1 - ON IEC Status OpEx.general: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 119

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.17 Circuit breaker failure protection 50BF(RBRF1)

RBRF1.OpIn

No. Information

1480 50BF (internal) TRIP (50BF int TRIP) 0 1

RBRF1.OpIn.general 0 1

device annunciation: 1 - ON IEC Status OpIn.general: 0 - FALSE

0 - OFF 1 - TRUE
x - irrelevant

120 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.18 Synchronism and Voltage Check 25 (RSYNx)

2.18 Synchronism and Voltage Check 25 (RSYNx)

RSYN1.Mod

No. Information

170.2101 Sync-group 1 is switched OFF (25-1 OFF) 0 1

RSYN1.Mod.stVal 1 5

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

RSYN1.Health

No. Information

170.0050 25 Synchronization Error (25 Sync. Error) x x 1 0

51 Device is Operational and Protecting (Device OK) x x 1 1

170.2096 25 Multiple selection of func-groups (25 FG-Error) 1 x 0 0

170.2097 25 Setting error (25 Set-Error) x 1 0 0

RSYN1.Health.stVal 3 3 2 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
x - irrelevant 3 - ALARM

RSYN1.Rel

No. Information

170.0049 25 Sync. Release of CLOSE Command (25 CloseRelease) 0 1

RSYN1.Rel.stVal 0 1

device annunciation: 1 - ON IEC Status Rel.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 121

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.18 Synchronism and Voltage Check 25 (RSYNx)

RSYN1.VInd

No. Information

170.2030 25 Voltage difference (Vdiff) okay (25 Vdiff ok) 0 1

RSYN1.VInd.stVal 1 0

device annunciation: 1 - ON IEC Status VInd.stVal: 0 - FALSE

0 - OFF 1 - TRUE

RSYN1.AngInd

No. Information

170.2032 25 Angle difference (alphadiff) okay (25 diff ok) 0 1

RSYN1.AngInd.stVal 1 0

device annunciation: 1 - ON IEC Status AngInd.stVal: 0 - FALSE

0 - OFF 1 - TRUE

RSYN1.HzInd

No. Information

170.2031 25 Frequency difference (fdiff) okay (25 fdiff ok) 0 1

RSYN1.HzInd.stVal 1 0

device annunciation: 1 - ON IEC Status HzInd.stVal: 0 - FALSE

0 - OFF 1 - TRUE

RSYN1.SynPrg

No. Information

170.2022 25-group 1: measurement in progress (25-1 meas.) 0 1

RSYN1.SynPrg.stVal 0 1

device annunciation: 1 - ON IEC Status SynPrg.stVal: 0 - FALSE

0 - OFF 1 - TRUE

122 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.18 Synchronism and Voltage Check 25 (RSYNx)

RSYN1.DifVCIc

No. Information Value

170.2054 dV = (dV =) RSYN1.DifVClc.mag.f Measured value Absolute value

RSYN1.DifVClc.units.SIUnit 29 V (Volt)

RSYN1.DifVClc.units.multiplier 3 Kilo

RSYN1.DifHzCIc

No. Information Value

170.2055 df = (df =) RSYN1. DifHzClc.mag.f Measured value Absolute value

RSYN1. DifHzClc.units.SIUnit 33 Hz

RSYN1. DifHzClc.units.multiplier 0 1

RSYN1.DifAngCIc

No. Information Value

170.2056 dalpha = (d =) RSYN1. DifAngClc.mag.f Measured value Absolute value

RSYN1. DifAngClc.units.SIUnit 9 ° (Degree)

RSYN1. DifAngClc.units.multiplier 0 1

SIPROTEC, 7SJ66, IEC61850 MAPPING 123

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.19 Three-pole tripping 52 Breaker (XCBR1)

2.19 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 1 0

XCBR1.Mod.stVal 1 5

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

XCBR1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

XCBR1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
x - irrelevant 3 - ALARM

XCBR1.Loc

No. Information

55 Reset Device (Reset Device) 1 0

XCBR1.Loc.stVal 1 0

device annunciation: 1 - ON IEC Status Loc.stVal: 0 - FALSE

0 - OFF 1 - TRUE

XCBR1.OpCnt

No. Information Value

Number of TRIPs= (#of XCBR1.OpCnt.stVal Metered value Absolute value

TRIPs=)

124 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.19 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.Pos

No. Information

4601 >52-a contact (OPEN, if bkr is open) (>52-a) 0 1 0 1

4602 >52-b contact (OPEN, if bkr is closed) (>52-b) 0 0 1 1

XCBR1.Pos.stVal - if spontan information 11 01 10 11

XCBR1.Pos.stVal - if command is running 00 01 10 00

device annunciation: 1 - ON IEC Status Pos.stVal: 00 - INTERMEDIATE STATE

0 - OFF 01 - OFF
10 - ON
11 - BAD STATE

XCBR1.BlkOpn

No. Information

55 Reset Device (Reset Device) 1 0

XCBR1.BlkOpn.stVal 0 1

device annunciation: 1 - ON IEC Status BlkOpn.stVal: 0 - FALSE

0 - OFF 1 - TRUE

XCBR1.BlkCls

No. Information

55 Reset Device (Reset Device) 1 0

XCBR1.BlkCls.stVal 0 1

device annunciation: 1 - ON IEC Status BlkCls.stVal: 0 - FALSE

0 - OFF 1 - TRUE

XCBR1.CBOpCap

No. Information

XCBR1.CBOpCap.stVal 1

device annunciation: IEC Status CBOpCap.stVal: 1 - NONE

SIPROTEC, 7SJ66, IEC61850 MAPPING 125

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.19 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.CirSpv

No. Information

6865 74TC Failure Trip Circuit (74TC Trip cir.) 0 1

XCBR1.CirSpv.stVal 0 1

device annunciation: 1 - ON IEC Status CirSpv.stVal: 0 - FALSE

0 - OFF 1 - TRUE

126 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.19 Three-pole tripping 52 Breaker (XCBR1)

XCBR1.SumSwARs1

No. Information Value

1021 Accumulation of XCBR1.SumSwARs1.actVal Metered value Current value of

interrupted current Ph A acummulated interrupted
( Ia =) current = actVal  pulsQty

XCBR1.SumSwARs1.units.SIUnit 5 A (Ampere)

XCBR1.SumSwARs1.units.multiplier 3 Kilo

XCBR1.SumSwARs1.pulsQty 1.000000e-002 A / Metered value

XCBR1.SumSwARs2

No. Information Value

1022 Accumulation of XCBR1.SumSwARs2.actVal Metered value Current value of

interrupted current Ph B acummulated interrupted
( Ib =) current = actVal  pulsQty

XCBR1.SumSwARs2.units.SIUnit 5 A (Ampere)

XCBR1.SumSwARs2.units.multiplier 3 Kilo

XCBR1.SumSwARs2.pulsQty 1.000000e-002 A / Metered value

XCBR1.SumSwARs3

No. Information Value

1023 Accumulation of XCBR1.SumSwARs3.actVal Metered value Current value of

interrupted current Ph C acummulated interrupted
( Ic =) current = actVal  pulsQty

XCBR1.SumSwARs3.units.SIUnit 5 A (Ampere)

XCBR1.SumSwARs3.units.multiplier 3 Kilo

XCBR1.SumSwARs3.pulsQty 1.000000e-002 A / Metered value

SIPROTEC, 7SJ66, IEC61850 MAPPING 127

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.20 Tripping Logic of the Entire Device (PTRC1)

2.20 Tripping Logic of the Entire Device (PTRC1)

PTRC1.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 0 1 1

52 At Least 1 Protection Funct. is Active (ProtActive) x 0 1

PTRC1.Mod.stVal 5 5 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF

PTRC1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

PTRC1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

PTRC1.Str

No. Information

501 Relay PICKUP (Relay PICKUP) 0 1

PTRC1.Str.general 0 1

device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

128 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.20 Tripping Logic of the Entire Device (PTRC1)

PTRC1.Tr

No. Information

511 Relay GENERAL TRIP command (Relay TRIP) 0 1

PTRC1.Tr.general 0 1

device annunciation: 1 - ON IEC Status Tr.general: 0 - FALSE

0 - OFF 1 - TRUE

PTRC1.FinTr

No. Information

2863 79 - Lockout (79 Lockout) 0 1

PTRC1.FinTr.stVal 0 1

device annunciation: 1 - ON IEC Status FinTr.stVal: 0 - FALSE

0 - OFF 1 - TRUE

SIPROTEC, 7SJ66, IEC61850 MAPPING 129

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.21 Measurement (MMXU1, MSQI1, MMTR1)

2.21 Measurement (MMXU1, MSQI1, MMTR1)

2.21.1 Measures (MMXU1)

MMXU1.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

MMXU1.Mod.stVal 0 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

MMXU1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

MMXU1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

130 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.21 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.TotW

No. Information Value

641 P (active power) (P =) MMXU1.TotW.mag.f Measured value Absolute value

MMXU1.TotW.units.SIUnit 62 W (Watt)

MMXU1.TotW.units.multiplier 6 Mega

MMXU1.TotVAr

No. Information Value

642 Q (reactive power) (Q =) MMXU1.TotVAr.mag.f Measured value Absolute value

MMXU1.TotVAr.units.SIUnit 63 VAr

MMXU1.TotVAr.units.multiplier 6 Mega

MMXU1.TotVA

No. Information Value

645 S (apparent power) (S =) MMXU1.TotVA.mag.f Measured value Absolute value

MMXU1.TotVA.units.SIUnit 61 VA

MMXU1.TotVA.units.multiplier 6 Mega

MMXU1.TotPF

No. Information Value

901 Power Factor (PF =) MMXU1.TotPF.mag.f Measured value Absolute value

MMXU1.TotPF.units.SIUnit 1 NONE

MMXU1.TotPF.units.multiplier 0 1

SIPROTEC, 7SJ66, IEC61850 MAPPING 131

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.21 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.Hz

No. Information Value

644 Frequency (Freq=) MMXU1.Hz.mag.f Measured value Absolute value

MMXU1.Hz.units.SIUnit 33 Hz

MMXU1.Hz.units.multiplier 0 1

MMXU1.A

No. Information Value

601 Ia (Ia =) MMXU1.A.phsA.cVal.mag.f Measured value Absolute value

MMXU1.A.phsA.units.SIUnit 5 A (Ampere)

MMXU1.A.phsA.units.multiplier 0 1

No. Information Value

602 Ib (Ib =) MMXU1.A.phsB.cVal.mag.f Measured value Absolute value

MMXU1.A.phsB.units.SIUnit 5 A (Ampere)

MMXU1.A.phsB.units.multiplier 0 1

No. Information Value

603 Ic (Ic =) MMXU1.A.phsC.cVal.mag.f Measured value Absolute value

MMXU1.A.phsC.units.SIUnit 5 A (Ampere)

MMXU1.A.phsC.units.multiplier 0 1

No. Information Value

604 In (In =) MMXU1.A.neut.cVal.mag.f Measured value Absolute value

MMXU1.A.neut.units.SIUnit 5 A (Ampere)

MMXU1.A.neut.units.multiplier 0 1

132 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.21 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.PPV

No. Information Value

624 Va-b (Va-b=) MMXU1.PPV.phsAB.cVal.mag.f Measured value Absolute value

MMXU1.PPV.phsAB.units.SIUnit 29 V (Volt)

MMXU1.PPV.phsAB.units.multiplier 3 Kilo

No. Information Value

625 Vb-c (Vb-c=) MMXU1.PPV.phsBC.cVal.mag.f Measured value Absolute value

MMXU1.PPV.phsBC.units.SIUnit 29 V (Volt)

MMXU1.PPV.phsBC.units.multiplier 3 Kilo

No. Information Value

626 Vc-a (Vc-a=) MMXU1.PPV.phsCA.cVal.mag.f Measured value Absolute value

MMXU1.PPV.phsCA.units.SIUnit 29 V (Volt)

MMXU1.PPV.phsCA.units.multiplier 3 Kilo

SIPROTEC, 7SJ66, IEC61850 MAPPING 133

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.21 Measurement (MMXU1, MSQI1, MMTR1)

MMXU1.PhV

No. Information Value

621 Va (Va =) MMXU1.PhV.phsA.cVal.mag.f Measured value Absolute value

MMXU1.PhV.phsA.units.SIUnit 29 V (Volt)

MMXU1.PhV.phsA.units.multiplier 3 Kilo

No. Information Value

622 Vb (Vb =) MMXU1.PhV.phsB.cVal.mag.f Measured value Absolute value

MMXU1.PhV.phsB.units.SIUnit 29 V (Volt)

MMXU1.PhV.phsB.units.multiplier 3 Kilo

No. Information Value

623 Vc (Vc =) MMXU1.PhV.phsC.cVal.mag.f Measured value Absolute value

MMXU1.PhV.phsC.units.SIUnit 29 V (Volt)

MMXU1.PhV.phsC.units.multiplier 3 Kilo

No. Information Value

627 VN (VN =) MMXU1.PhV.neut.cVal.mag.f Measured value Absolute value

MMXU1.PhV.neut.units.SIUnit 29 V (Volt)

MMXU1.PhV.neut.units.multiplier 3 Kilo

134 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.21 Measurement (MMXU1, MSQI1, MMTR1)

2.21.2 Measured values, symmetrical components (MSQI1)

MSQI1.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

MSQI1.Mod.stVal 0 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

MSQI1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

MSQI1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

SIPROTEC, 7SJ66, IEC61850 MAPPING 135

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.21 Measurement (MMXU1, MSQI1, MMTR1)

MSQI1.SeqA

No. Information Value

605 I1 (positive sequence) (I1 =) MSQI1.SeqA.c1.cVal.mag.f Measured value Absolute value

MSQI1.SeqA.c1.units.SIUnit 5 A (Ampere)

MSQI1.SeqA.c1.units.multiplier 0 1

No. Information Value

606 I2 (negative sequence) (I2 =) MSQI1.SeqA.c2.cVal.mag.f Measured value Absolute value

MSQI1.SeqA.c2.units.SIUnit 5 A (Ampere)

MSQI1.SeqA.c2.units.multiplier 0 1

No. Information Value

831 3Io (zero sequence) (3Io =) MSQI1.SeqA.c3.cVal.mag.f Measured value Absolute value

MSQI1.SeqA.c3.units.SIUnit 5 A (Ampere)

MSQI1.SeqA.c3.units.multiplier 0 1

MSQI1.SeqV

No. Information Value

629 V1 (positive sequence) (V1 =) MSQI1.SeqV.c1.cVal.mag.f Measured value Absolute value

MSQI1.SeqV.c1.units.SIUnit 29 V (Volt)

MSQI1.SeqV.c1.units.multiplier 3 Kilo

No. Information Value

630 V2 (negative sequence) (V2 =) MSQI1.SeqV.c2.cVal.mag.f Measured value Absolute value

MSQI1.SeqV.c2.units.SIUnit 29 V (Volt)

MSQI1.SeqV.c2.units.multiplier 3 Kilo

No. Information Value

832 Vo (zero sequence) (Vo =) MSQI1.SeqV.c3.cVal.mag.f Measured value Absolute value

MSQI1.SeqV.c3.units.SIUnit 29 V (Volt)

MSQI1.SeqV.c3.units.multiplier 3 Kilo

136 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
 Mapping

2.21 Measurement (MMXU1, MSQI1, MMTR1)

2.21.3 Power Metering (MMTR1)

MMTR1.Mod

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

MMTR1.Mod.stVal 0 1

device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF

MMTR1.Health

No. Information

51 Device is Operational and Protecting (Device OK) 0 1

MMTR1.Health.stVal 3 1

device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

MMTR1.SupWh

No. Information Value

924 Wp Forward (Wp+=) MMTR1.SupWh.actVal Metered value Current value of acummulated

interrupted current =
actVal  pulsQty

MMTR1.SupWh.units.SIUnit 72 Wh

MMTR1.SupWh.units.multiplier 6 Mega

MMTR1.SupWh.pulsQty 3.464200e-005 Wh / Metered value

SIPROTEC, 7SJ66, IEC61850 MAPPING 137

C53000-L2640-C554-2, Edition 12.2017
Mapping
2.21 Measurement (MMXU1, MSQI1, MMTR1)

MMTR1.SupVArh

No. Information Value

925 Wq Forward (Wq+=) MMTR1.SupVArh.actVal Metered value Current value of acummulated

interrupted current =
actVal  pulsQty

MMTR1.SupVArh.units.SIUnit 73 VArh

MMTR1.SupVArh.units.multiplier 6 Mega

MMTR1.SupVArh.pulsQty 3.464200e-005 VArh / Metered value

MMTR1.DmdWh

No. Information Value

928 Wp Reverse (Wp-=) MMTR1.DmdWh.actVal Metered value Current value of acummulated

interrupted current =
actVal  pulsQty

MMTR1.DmdWh.units.SIUnit 72 Wh

MMTR1.DmdWh.units.multiplier 6 Mega

MMTR1.DmdWh.pulsQty 3.464200e-005 Wh / Metered value

MMTR1.DmdVArh

No. Information Value

929 Wq Reverse (Wq-=) MMTR1.DmdVArh.actVal Metered value Current value of acummulated

interrupted current =
actVal  pulsQty

MMTR1.DmdVArh.units.SIUnit 73 VArh

MMTR1.DmdVArh.units.multiplier 6 Mega

MMTR1.DmdVArh.pulsQty 3.464200e-005 VArh / Metered value

138 SIPROTEC, 7SJ66, IEC61850 MAPPING

C53000-L2640-C554-2, Edition 12.2017
Literature

/1/ SIPROTEC 4 System Description

E50417-H1176-C151
/2/ SIPROTEC DIGSI, StartUP
E50417-G1176-C152
/3/ DIGSI CFC, Manual
E50417-H1176-C098
/4/ SIPROTEC SIGRA 4, Manual
E50417-H1176-C1100-C070

SIPROTEC, 7SJ66, IEC61850 MAPPING 139

C53000-L2640-C554-2, Edition 12.2017
140 SIPROTEC, 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-2, Edition 12.2017
Index

C PhV 134
CALH1 12, 21, 31 PPV 133
ErrBoard1 32 TotPF 131
ErrBoard2 32 TotVA 131
ErrBoard3 32 TotVAr 131
ErrBoard4 32 TotW 131
ErrBoard5 33 MSQI1 12, 20, 135
ErrBoard6 33 Health 135
ErrBoard7 33 Mod 135
GrAlm 31 SeqA 136
GrWrn 31 SeqV 136
Health 31
Mod 31
P
PHIZ1 15, 19, 100
D Health 100
DOI 11 Mod 100
Op 104
F Str.dirGeneral 101
Function parameters 12 Str.dirPhsA 102
Functional Scope Str.dirPhsB 103
7SJ66 13 Str.dirPhsC 104
Str.general 100
L Str.phsA 101
LD Str.phsB 102
CTRL (Control) 12, 21 Str.phsC 103
DR (Disturbance Recorder) 20 PMLJ1 16, 19, 79
EXT (Extended) 21 Health 79
Logical Device 10 LodJamAlm 80
MEAS (Measurement) 12, 20 Mod 79
PROT (Protection) 12, 18 Op 80
LLN0 10, 12, 18, 20, 21 Str 80
Beh 22, 24, 25 PMRI1 16, 19, 78
Health 22, 24, 25 Health 78
Mod 24, 25 Mod 78
OpTmh 23, 26 Op 78
Logical Node 11, 13, 18 StrInhTmm 78
LPHD1 10, 12, 19, 20, 21, 30 PMSS1 16, 19, 76
DevStr 30 Health 76
PhyHealth 30 Mod 76
Proxy 30 Op 77
Str 77
M PSD 110
MMTR1 12, 20, 137 PSDE1 15, 19, 105
DmdVArh 138 Health 105
DmdWh 138 Mod 105
Health 137 Op 106
Mod 137 Str.dirGeneral 106
SupVArh 138 Str.general 105
SupWh 137 PSDE2 15, 19, 106
MMXU1 12, 20, 130 Health 106
A 132, 135 Mod 106
Health 130 Op 107
Hz 132 Str.dirGeneral 107
Mod 130 Str.general 107

141
SIPROTEC, 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-2, Edition 12.2017
PSDE3 15, 19, 108 Op 56
Health 108 Str 55
Mod 108 PTOC14 15, 19, 72
Op 109 Health 72
Str.dirGeneral 109, 116 Mod 72
Str.general 108, 116 Op 72
PSDE4 15, 19, 110 Str 72
Health 110 PTOC15 15, 19, 73
Mod 110 Health 73
Op 111 Mod 73
Str. 110 Op 73
Str.dirGeneral 111 Str 73
PSDE5 15, 19 PTOC16 15, 18, 63
Health 112 Health 63
Mod 111 Mod 63
Op 112 Op 63
Str 112 Str 63
Str.dirGeneral 112 PTOC17 15, 18, 64
PSDE6 15, 19, 110 Health 64
Health 113 Mod 64
Mod 113 Op 65
Op 114 Str 65
Str 113 PTOC18 13, 18
Str.dirGeneral 113 Health 38
PSDE7 15, 19, 110 Mod 38
Health 114 Op 39
Mod 114 Str 39
Op 115 PTOC19 14, 18
Str 114 ChgSet 51
Str.dirGeneral 115 Health 51
PTOC1 13, 18, 39 Mod 50
ChgSet 40 Op 51
Health 40 Str 51
Mod 39 PTOC2 13, 18, 43
Op 40 ChgSet 44
Str 40 Health 43
PTOC10 14, 18, 48 Mod 43
ChgSet 49 Op 44
Health 48 Str 44
Mod 48 PTOC20 14, 18
Op 49 ChgSet 57
Str 48 Health 56
PTOC11 14, 18, 49, 50 Mod 56
ChgSet 50 Op 57
Health 49 Str 57
Mod 49 PTOC3 14, 18, 52
Op 50 ChgSet 53
Str 50 Health 52
PTOC12 14, 18, 54 Mod 52
ChgSet 55 Op 52
Health 54 Str 52
Mod 54 PTOC4 14, 18, 57
Op 54 ChgSet 58
Str 54 Health 58
PTOC13 14, 18, 55, 56 Mod 57
ChgSet 56 Op 58
Health 55 Str 58
Mod 55 PTOC5 15, 19, 74

SIPROTEC, 7SJ66, IEC61850 MAPPING 142

C53000-L2640-C554-2, Edition 12.2017
 Health 74 Mod 71
Mod 74 Op 71
Op 75 Str 71
Str 75 PTRC1 12, 18, 128
PTOC6 13, 18, 36 FinTr 129
ChgSet 37 Health 128
Health 36 Mod 128
Mod 36 Str 128
Op 36 Tr 129
Str 36 PTRC2 13, 18, 45
PTOC7 13, 18, 37 Health 45
ChgSet 38 Mod 41, 45
Health 37 Op 41, 47
Mod 37 Str 45
Op 38 Str.dirGeneral 45
Str 37 Str.dirNeut 47
PTOC8 13, 18 Str.dirPhsA 46
ChgSet 42 Str.dirPhsB 46
Health 41 Str.dirPhsC 47
Mod 41 Str.neut 47, 62
Op 41 Str.phsA 46
Str 41 Str.phsB 46, 47, 61, 62
PTOC9 13, 18, 42 Str.phsC 46, 47, 61, 62
ChgSet 43 PTRC3 14, 18, 59
Health 42 Health 59
Mod 42 Mod 59
Op 43 Op 62
Str 42 Str 59
PTOF1 16, 19, 89 Str.dirGeneral 60
BlkV 90 Str.dirNeut 62
Health 89 Str.dirPhsA 60
Mod 89, 91 Str.dirPhsB 61
Op 90 Str.dirPhsC 61
Str 90 Str.neut 62
PTOF2 91 Str.phsA 60
BlkV 92 Str.phsB 61
Health 91 Str.phsC 61
Mod 91 PTTR1 16, 19, 98
Op 92 AlmThm 99
Str 92 Health 98
PTOF3 93 Mod 98
BlkV 94 Str 98
Health 93 Tr 99
Mod 93 PTUF1 16, 19, 81
Op 94 BlkV 82
Str 94 Health 81
PTOF4 95 Mod 81
BlkV 96 Op 82
Health 95 Str 82
Mod 95 PTUF2 83
Op 96 BlkV 84
Str 96 Health 83
PTOV1 16, 18, 70 Mod 83
Health 70 Op 84
Mod 70 Str 84
Op 70 PTUF3 85
Str 70 BlkV 86
PTOV2 16, 71 Health 85
Health 71 Mod 85

143
SIPROTEC, 7SJ66, IEC61850 MAPPING
C53000-L2640-C554-2, Edition 12.2017
 Op 86 Mod 121
Str 86 Rel 121
PTUF4 87 SynPrg 122
BlkV 88 VInd 122
Health 87 RSYN2
Mod 87 DifAngCIc 123
Op 88 DifVCIc 123
Str 88 Health 123
PTUV1 16, 18, 66, 97 RSYN3
Health 66 DifVCIc 123
Mod 66 RSYN4
Op 67 HzInd 124
Str 67
PTUV2 16, 68 X
Health 68 XCBR1 12, 18, 124
Mod 68 BlkCls 125
Op 69 BlkOpn 125
Str 69 CBOpCap 125
PTUV7 19 CirSpv 126
Health 97 Health 124
Mod 97 Loc 124
Op 97 Mod 124
Str 97 OpCnt 124
PVOC1 Pos 125
Mod 41, 47 SumSwARs1 127
SumSwARs2 127
R SumSwARs3 127
RBRF1 16, 19, 119
Health 119
Mod 119
OpEx 119
OpIn 120
Str 119
RDRE1 13, 20, 34
FltNum 34
GriFltNum 34
Health 34
Mod 34
RcdMade 34, 35
RcdStr 35
RFLO1 17, 19, 117
FltDiskm 118
FltDisPrc 118
FltZ 117
Health 117
Mod 117
RREC1 16, 19, 116
AutoRecSt 116
Health 116
Mod 116
Op 116
RSYN1 16, 21, 121
AngInd 122
DifAngCIc 123
DifHzCIc 123
DifVCIc 123
Health 121
HzInd 122

SIPROTEC, 7SJ66, IEC61850 MAPPING 144

C53000-L2640-C554-2, Edition 12.2017