Scribd Logo
Upload

Welcome to Scribd!

  • 20 views

    Series 1000: Oscillator/Demodulator

    Uploaded by

    ghrd
    The Series 1000 Oscillator/Demodulators provide electrical support for AC LVDT transducers. It generates a stable excitation voltage for the transducer and converts the LVDT's secondary voltages into a DC output voltage or 4-20mA current. The demodulator has automatic phase synchronization, eliminating the need for phase adjustments. Models are available for voltage or current output, with different frequency response capabilities depending on the LVDT's phase angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Series 1000: Oscillator/Demodulator

    Uploaded by

    ghrd
    20 views2 pages
    The Series 1000 Oscillator/Demodulators provide electrical support for AC LVDT transducers. It generates a stable excitation voltage for the transducer and converts the LVDT's secondary voltages into a DC output voltage or 4-20mA current. The demodulator has automatic phase synchronization, eliminating the need for phase adjustments. Models are available for voltage or current output, with different frequency response capabilities depending on the LVDT's phase angle.

    Original Description:

    hkhgu

    Original Title

    TRANS-2016-1000

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The Series 1000 Oscillator/Demodulators provide electrical support for AC LVDT transducers. It generates a stable excitation voltage for the transducer and converts the LVDT's secondary voltages into a DC output voltage or 4-20mA current. The demodulator has automatic phase synchronization, eliminating the need for phase adjustments. Models are available for voltage or current output, with different frequency response capabilities depending on the LVDT's phase angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    20 views2 pages

    Series 1000: Oscillator/Demodulator

    Uploaded by

    ghrd
    The Series 1000 Oscillator/Demodulators provide electrical support for AC LVDT transducers. It generates a stable excitation voltage for the transducer and converts the LVDT's secondary voltages into a DC output voltage or 4-20mA current. The demodulator has automatic phase synchronization, eliminating the need for phase adjustments. Models are available for voltage or current output, with different frequency response capabilities depending on the LVDT's phase angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Series 1000

    Oscillator/Demodulator
    The Series 1000 Oscillator/Demodulators provide complete electrical support
    for AC LVDTs. Working from an unregulated DC input, the modules generate a
    stable sinusoidal excitation voltage for the transducer. The LVDT’s secondary
    voltages are converted into DC voltage by the module’s phase sensitive
    demodulator. The demodulator has automatic phase synchronization which
    simplifies installation and setup by eliminating the need to make phase angle
    adjustments for each transducer. An active, three-pole filter in the final stage
    reduces output ripple while maximizing frequency response. Other features
    include zero and span controls, full encapsulation, threaded inserts for
    mounting, and self-locking terminal strips.

    KEY FEATURES
    Works with 5 and 6 wire LVDTs Internally Regulated
    DC Voltage or 4-20mA Output High Frequency Response

    ELECTRICAL SPECIFICATIONS
    Voltage ±14.5 to ±28VDC, Input polarity protected. NOTE: DUAL DC OUTPUT POWER SUPPLY REQUIRED.
    INPUT POWER
    Current ±150mA MAX. plus LVDT current
    Voltage 4.25 to 5.75VRMS adjustable via 15 turn span control
    OSCILLATOR OUTPUT TO LVDT
    Current Will drive LVDTs with primary impedance of 100Ω or greater. Short circuit and thermally protected
    SIGNAL OUTPUT – VOLTAGE Voltage DC output is 2 times the RMS output of the LVDT. Output voltage is limited to ±12VDC.
    Current ±3mA without distortion
    MODELS 1000-0011, 1000-0012,
    Impedance Less than 5Ω
    1000-0014
    Ripple 0.015VRMS MAX.
    SIGNAL OUTPUT – CURRENT Current 4-20mA output with LVDT whose sensitivity is 0.5V/V (±10%). Min. Full Scale Output current: 2-22mA
    MODELS 1000-0021, 1000-0022,
    Load Impedance >1x1010Ω; Operation into loop impedance between 5 and 400Ω
    1000-0024
    Non-Linearity ±0.05% MAX. over ±10VDC output
    ACCURACY
    Temp. Coefficient < ±0.00025V/°F Zero, < ±0.01% output/°F Span
    Operating Temp. +32°F to +158°F (0°C to +70°C)
    TEMPERATURE RANGE
    Storage Temp. -67°F to +257°F (-55°C to +125°C)
    ZERO ADJUSTMENT ±0.40 MIN. VDC via 15 turn zero control
    TERMINAL CONNECTIONS Friction terminals with self-locking screws, accepts up to #16 AWG wire

    BLOCK
    DIAGRAM

    Tel: 800-828-3964 | Fax: 860-872-4211 | Web: www.transtekinc.com


    S012-0070 Revision 1
    INTERCONNECTION DIAGRAM DIMENSIONAL DIAGRAM

    NOTE:
    1. 4 wire LVDT connection requires access to the center connection of both
    secondaries. One wire from each of the secondaries and the primary will be
    tied together and attached to COMMON. The remaining three leads will be
    connected as shown in the connection.

    VOLTAGE AND 4-20mA OUTPUT VERSIONS


    The equivalent models for voltage and 4-20mA output are shown in the table below, along with frequency, phase angle and frequency response
    for each. All of these modules are physically identical and require the same dual bipolar voltage supply. The output pins 5 and 1 are used for the
    current output.

    VDC MODEL 4-20mA MODEL FREQUENCY, KHz ±10% LVDT PHASE ANGLE FREQUENCY RESPONSE, Hz
    1000-0011 1000-0021 3 All > 500
    1000-0012 1000-0022 7 > 10 Degrees > 1000
    1000-0014 1000-0024 7 < 10 Degrees > 1000

    NOTE:
    Current Loop impedance must be between 5 and 400Ω for linear operation.

    SALES OPTION
    OPTION # DESCRIPTION
    X0003 Provide special zero offset and/or sensitivity
    X0005 Provide special cutoff frequency

    Tel: 800-828-3964 | Fax: 860-872-4211 | Web: www.transtekinc.com


    S012-0070 Revision 1

    You might also like