SEA CHEST AND SEA CONN.

BLANKS
For Under Water Survey

SEA CHEST & SEA CONN. BLANKS

For Under Water Survey

SEA CHEST HULL APERTURE BLANKS

2009 October. GS HIGH TECHER CO., LTD. All Reserved. Printed in KOREA MAGNETIC TYPE

GS HIGH TECHER CO., LTD.

1480-10, Songjeong-Dong, Kangseo-Ku, Busan, 618-270, Korea
Tel. +82-51-832-0456 Fax. +82-51-832-0457 E-mail. [email protected]
http://gshightecher.koreasme.com http://www.ec21.com
GS HIGH TECHER
 gshightecher.coreasme.com
GS HIGH TECHER

SEA CHEST & SEA CONN. BLANK 1. INSTRUCTION MANUAL

FOR UNDER WATER SURVEY. GENERAL
A ship consists of many machine including main engine, ancillary equipment and generator in the engine
room. These machine usually generate a lot of heats while operating. The sea water can generally be used (1)TYPE-A, TYPE-B & TYPE-C (FIG 1-1)
to cool down such heat. For the cooling system, you have to weld the pipes to the seawater inlet / outlet The Necessary operation work to attach all types (from type A to type C) plug is performed manually by drivers without
special tools. All types consist of soft rubber, which is enlarged in the diameter of ship enlarged in the diameter of ship
to mount a flange where you can install the shutoff valves. If these valves would be required to be fixed or
side hole by turning the operating part. Direct shell connections and sea connection pipe now can be sealed with the
replaced, you can conveniently use the SEA CONNECTION PlUG to prevent the seawater from flowing into shell plate by divers without docking. Therefore, ship side hole be seal tightly. Each pipe plug must be marked with the
the ship while removing them. pipe identification numbers mentioned in the general plan.

Development Efficience (2)TYPE-E(FIG 1-2)

TYPE-D consists of soft rubber, which is enlarged in the dimeter of air vent hole and drain small hole by pushing
You do not need to bring the ship into the dry dock for repairing the valves. You may simply insert the plug into the operation part. Therefore, air vent hole and drain hole shall be sealed tightly.
opening of the pipes, and then secure with lock handle while reparing or replacing the valves.
(3)TYPE-E&F(FIG 3)
Sea chest convering system are possible to seal the sea chest on outside vessel. Repairs, cleaning, cleaning and working
▶ Reusable.
on suction lines can be performed. G.S sea chest covering system is easy to install by diver. Before installation, all parts
▶ Easy to use with its simple structure. are to be secured for damages. It is fitted through hull apeature side evenly. A loop is fitted on the one area to prevent
▶ Easy to move for the underwater survey. from missing sea chest covering system. The loop must be connected with the rope which supplied from the deck. It is
fitted on the hull apearture part with over 3500 gauss magnetic solidity, then the water tightness must be perfected.
After using the covering system, take off each end of the angle part. Drain opening the sea chest covering system must
SEA CONNECTION PLUG SEA CONN. BLANKING COVER be installed. Finally a large Q’TY of water should be drained to the bilge, then the covers is pressed on the cover which
take up full pressing power. Sea chest covering system hull aperture blanks are possible to seal the sea chest on outside
<SMALL SIZE> <LARGE SIZE> vessel. Repairs, cleaning, and working on suction lines can be performed.

<FIG-1>
<FIG1-1> <FIG1-2>
SHIP'S HULL HOOK SUPPORT
SHIP'S HULL
SHELL PLATE SHELL PLATE

OPER. HANDLE

PUSH Type operating handle type cover type SHIP SIDE VALVE SEA CONNECTION
SHIP SIDE VALVE
BRACKET PIPE PLUG

SEA CHEST HULLAPERTURE BLANKS BRACKET

<MAGNETIC BLANKET TYPE> <GENERAL BLANKET TYPE>

AIR VENT HOLE <FIG-2> <FIG3>
SE
E
DE
<FIG2-1>
TA
SEA CHEST IL

DRAIN & AIR <FIG2-2>

VENT HOLE PLUG

OPER. HANDLE

DRAIN HOLE PU
SH
SHIP'S HULL SHELL PLATE EYE BOLT & NUT

PUSH

02 03
 gshightecher.coreasme.com
GS HIGH TECHER

SEA CHEST & SEA CONN. BLANK 1. INSTRUCTION MANUAL

FOR UNDER WATER SURVEY. GENERAL
A ship consists of many machine including main engine, ancillary equipment and generator in the engine
room. These machine usually generate a lot of heats while operating. The sea water can generally be used (1)TYPE-A, TYPE-B & TYPE-C (FIG 1-1)
to cool down such heat. For the cooling system, you have to weld the pipes to the seawater inlet / outlet The Necessary operation work to attach all types (from type A to type C) plug is performed manually by drivers without
special tools. All types consist of soft rubber, which is enlarged in the diameter of ship enlarged in the diameter of ship
to mount a flange where you can install the shutoff valves. If these valves would be required to be fixed or
side hole by turning the operating part. Direct shell connections and sea connection pipe now can be sealed with the
replaced, you can conveniently use the SEA CONNECTION PlUG to prevent the seawater from flowing into shell plate by divers without docking. Therefore, ship side hole be seal tightly. Each pipe plug must be marked with the
the ship while removing them. pipe identification numbers mentioned in the general plan.

Development Efficience (2)TYPE-E(FIG 1-2)

TYPE-D consists of soft rubber, which is enlarged in the dimeter of air vent hole and drain small hole by pushing
You do not need to bring the ship into the dry dock for repairing the valves. You may simply insert the plug into the operation part. Therefore, air vent hole and drain hole shall be sealed tightly.
opening of the pipes, and then secure with lock handle while reparing or replacing the valves.
(3)TYPE-E&F(FIG 3)
Sea chest convering system are possible to seal the sea chest on outside vessel. Repairs, cleaning, cleaning and working
▶ Reusable.
on suction lines can be performed. G.S sea chest covering system is easy to install by diver. Before installation, all parts
▶ Easy to use with its simple structure. are to be secured for damages. It is fitted through hull apeature side evenly. A loop is fitted on the one area to prevent
▶ Easy to move for the underwater survey. from missing sea chest covering system. The loop must be connected with the rope which supplied from the deck. It is
fitted on the hull apearture part with over 3500 gauss magnetic solidity, then the water tightness must be perfected.
After using the covering system, take off each end of the angle part. Drain opening the sea chest covering system must
SEA CONNECTION PLUG SEA CONN. BLANKING COVER be installed. Finally a large Q’TY of water should be drained to the bilge, then the covers is pressed on the cover which
take up full pressing power. Sea chest covering system hull aperture blanks are possible to seal the sea chest on outside
<SMALL SIZE> <LARGE SIZE> vessel. Repairs, cleaning, and working on suction lines can be performed.

<FIG-1>
<FIG1-1> <FIG1-2>
SHIP'S HULL HOOK SUPPORT
SHIP'S HULL
SHELL PLATE SHELL PLATE

OPER. HANDLE

PUSH Type operating handle type cover type SHIP SIDE VALVE SEA CONNECTION
SHIP SIDE VALVE
BRACKET PIPE PLUG

SEA CHEST HULLAPERTURE BLANKS BRACKET

<MAGNETIC BLANKET TYPE> <GENERAL BLANKET TYPE>

AIR VENT HOLE <FIG-2> <FIG3>
SE
E
DE
<FIG2-1>
TA
SEA CHEST IL

DRAIN & AIR <FIG2-2>

VENT HOLE PLUG

OPER. HANDLE

DRAIN HOLE PU
SH
SHIP'S HULL SHELL PLATE EYE BOLT & NUT

PUSH

02 03
 gshightecher.coreasme.com
GS HIGH TECHER

2. INSTALLATION SEA CONNECTION PIPE PLUG <FIG1-1>

OPERATING HANDLE A-TYPE
B

7
HANDLING MAGNET FOR SETTING POSITION

8
LIFTING LUG(LOOP)
6

V
SEA CHEST

L
4

J
* The Handling Magnet for setting position is not included purchasing Sea Chest Cover. 9
If you want to purchase the Handling Magnet for setting position, please notice that before an order.
ØH
1
G.S sea chest covering system is easy to install by a diver. Before installation, all parts to be secured for damages. To sink
the blanks, it required to sink the blanks over come its floatage first, the power for sinking the blanks, you can attach
properate weight to the designed loop from the deck through sup-plied rope. In case of without magnet type, it is fitted MATERIAL Unit : mm

through “c” shape hook and ropes from the deck. In case of magnetic type, you can spread a blank and attach to ship’s No. Name of part Q’ty Material
hull shell plate. 1 SHAFT 1 SM45C
Drain opening, the sea chest covering system must be installed & sealed. Finally a large q’ty of water should be drained 2 BASE PLATE 1 SS400
to the bilge, then the blanks is pressed on the the top which take up full pressing power. The sinking power are 3 SPRING WASHER 1 SWO
calculated against its volume of 80%. 4 RUBBER SEAL 1 NEOPRENE
5 TOP PLATE 1 SS400
6 SUPPORT BAR 1 STPG
7 OPERATING HANDLE 1 SS400
Volume calculation 8 COTTER PIN 1 SUS304
In 10 meter depth = 1 bar sea chest(75Ommhq/l000mbar) 9 HEX.NUT(1종) 1 SS400
Opening(cm) = pressing power
Ambient air temp. = 25°C
DIMENSION Unit : mm
Sea water temp. = 18°C
Sinking power(kg) =length x breadth x height x 80% φI.D
N.D φO.D L V B J REMARK
#160 #80 ETC. #160 #80 ETC.
25A 34.0 21.2 - - 18.4 - - 235 180 150 55
* care & storage 32A 42.7 29.9 - 32.0 27.1 - - 235 180 150 55
The coveds are stored for a long time without using. We recommend you clean
40A 48.6 34.4 38.4 - 31.6 - - 235 180 150 55
The rubber and metals with glycerine. It can be using for more than 15 years. 50A 60.5 43.1 49.5 - 40.3 - - 235 180 150 55
All g.s underwater covers must be marked name & size. After using covers. 65A 76.3 57.3 62.3 - 53.7 - - 235 180 150 55
It Can be with compressed air and dried. 80A 89.1 66.9 73.9 80.0 63.0 70.0 76.0 235 180 150 55
100A 114.3 87.3 97.1 94.0 82.9 94.3 90.0 235 180 150 55
125A 139.8 108.0 120.8 - 103.7 116.5 - 235 180 150 55
150A 165.2 128.8 143.2 - 124.1 138.5 - 235 180 150 55

04 05
 gshightecher.coreasme.com
GS HIGH TECHER

2. INSTALLATION SEA CONNECTION PIPE PLUG <FIG1-1>

OPERATING HANDLE A-TYPE
B

7
HANDLING MAGNET FOR SETTING POSITION

8
LIFTING LUG(LOOP)
6

V
SEA CHEST

L
4

J
* The Handling Magnet for setting position is not included purchasing Sea Chest Cover. 9
If you want to purchase the Handling Magnet for setting position, please notice that before an order.
ØH
1
G.S sea chest covering system is easy to install by a diver. Before installation, all parts to be secured for damages. To sink
the blanks, it required to sink the blanks over come its floatage first, the power for sinking the blanks, you can attach
properate weight to the designed loop from the deck through sup-plied rope. In case of without magnet type, it is fitted MATERIAL Unit : mm

through “c” shape hook and ropes from the deck. In case of magnetic type, you can spread a blank and attach to ship’s No. Name of part Q’ty Material
hull shell plate. 1 SHAFT 1 SM45C
Drain opening, the sea chest covering system must be installed & sealed. Finally a large q’ty of water should be drained 2 BASE PLATE 1 SS400
to the bilge, then the blanks is pressed on the the top which take up full pressing power. The sinking power are 3 SPRING WASHER 1 SWO
calculated against its volume of 80%. 4 RUBBER SEAL 1 NEOPRENE
5 TOP PLATE 1 SS400
6 SUPPORT BAR 1 STPG
7 OPERATING HANDLE 1 SS400
Volume calculation 8 COTTER PIN 1 SUS304
In 10 meter depth = 1 bar sea chest(75Ommhq/l000mbar) 9 HEX.NUT(1종) 1 SS400
Opening(cm) = pressing power
Ambient air temp. = 25°C
DIMENSION Unit : mm
Sea water temp. = 18°C
Sinking power(kg) =length x breadth x height x 80% φI.D
N.D φO.D L V B J REMARK
#160 #80 ETC. #160 #80 ETC.
25A 34.0 21.2 - - 18.4 - - 235 180 150 55
* care & storage 32A 42.7 29.9 - 32.0 27.1 - - 235 180 150 55
The coveds are stored for a long time without using. We recommend you clean
40A 48.6 34.4 38.4 - 31.6 - - 235 180 150 55
The rubber and metals with glycerine. It can be using for more than 15 years. 50A 60.5 43.1 49.5 - 40.3 - - 235 180 150 55
All g.s underwater covers must be marked name & size. After using covers. 65A 76.3 57.3 62.3 - 53.7 - - 235 180 150 55
It Can be with compressed air and dried. 80A 89.1 66.9 73.9 80.0 63.0 70.0 76.0 235 180 150 55
100A 114.3 87.3 97.1 94.0 82.9 94.3 90.0 235 180 150 55
125A 139.8 108.0 120.8 - 103.7 116.5 - 235 180 150 55
150A 165.2 128.8 143.2 - 124.1 138.5 - 235 180 150 55

04 05
 gshightecher.coreasme.com
GS HIGH TECHER

SEA CONNECTION PIPE PLUG <FIG1-1> SEA CONNECTION PIPE PLUG <FIG1-1>
OPERATING HANDLE B-TYPE OPERATING HANDLE C-TYPE

B
B

10
11
Ø16

L3
1
1
L3

11 C
10
C 9
12
8
9
L

L
L2
3
3
L2

7
6
6
5
5
4
8

L1
L1

2 4
3 2
13 3
12 14
ØH ØH
13

MATERIAL Unit : mm MATERIAL Unit : mm

No. Name of part Q’ty Material No. Name of part Q’ty Material No. Name of part Q’ty Materia
1 SHAFT 1 SM45C 1 SHAFT 1 SM45C 8 MIDDLE BAR 1 STPG
2 BASE PLATE 1 HDPE 2 BASE PLATE 1 HDPE 9 SUPPORT BAR 1 SPPS
3 WASHER 1 SS400 3 WASHER 1 SS400 10 OPERATING BAR 1 SPPS
4 O-RING 1 NBR 4 O-RING 1 NBR 11 FIXED HANDLE 1 -
5 RUBBER SEAL 1 NEOPRENE 5 RUBBER SEAL 1 NEOPRENE 12 THRUST BEARING 1 SS400
6 TOP PLATE 1 HOPE 6 TOP PLATE 1 HDPE 13 HEX.NUT 1 SWO
7 O-RING 1 NBR 7 O-RING 1 NBR 14 HEX.NUT 1 SWO
8 SUPPORT BAR 1 STPG
9 OPERATING HANDLE 1 SPPS
10 FIXED HANDLE 1 SPPS
DIMENSION Unit : mm

11 THRUST BEARING 1 - φI.D φH

N.D L L1 L2 L3 C B REMARK
12 HEX.NUT 1 SS400 #160 #80 ETC1. ETC2. #160 #80 ETC1. ETC2.
13 SPRING WAHSER 1 SWO 350A 284.2 317.6 323.6 - 278.7 312 315.6 - 454 130 188 136 300 350
400A 325.4 363.6 374.4 - 319.5 357.6 368.6 - 454 130 188 136 300 350
450A - 409.6 425.2 - - - 419.2 - 454 130 188 136 300 350
DIMENSION Unit : mm 500A - 455.6 476 - - - 468 - 454 130 188 136 300 350
φI.D φH 550A - - 526.8 - - - 518.8 - 454 130 188 136 300 350
N.D φO.D L L1 L2 L3 C B REMARK 600A - - 577.6 - - - 569 - 454 130 188 136 300 350
#160 #80 ETC1. ETC2. #160 #80 ETC1. ETC2.
200A 216.3 168.3 190.0 184.3 193 163.3 184.4 179.3 188 387 77 188 136 350 300 650A - - 628.4 - - - 619.4 - 454 130 188 136 300 350
250A 267.4 210.2 237.2 235.4 247 204.8 230.8 230.3 242.9 387 77 188 144 350 300 700A - - 679.2 667 - - 670.2 658 454 130 188 136 300 350
300A 318.5 283.7 283.7 286.5 299 246.4 277.2 278.7 294 387 77 188 144 350 300 750A - - 736.6 - - - 727.1 - 454 130 188 136 300 350

06 07
 gshightecher.coreasme.com
GS HIGH TECHER

SEA CONNECTION PIPE PLUG <FIG1-1> SEA CONNECTION PIPE PLUG <FIG1-1>
OPERATING HANDLE B-TYPE OPERATING HANDLE C-TYPE

B
B

10
11
Ø16

L3
1
1
L3

11 C
10
C 9
12
8
9
L

L
L2
3
3
L2

7
6
6
5
5
4
8

L1
L1

2 4
3 2
13 3
12 14
ØH ØH
13

MATERIAL Unit : mm MATERIAL Unit : mm

No. Name of part Q’ty Material No. Name of part Q’ty Material No. Name of part Q’ty Materia
1 SHAFT 1 SM45C 1 SHAFT 1 SM45C 8 MIDDLE BAR 1 STPG
2 BASE PLATE 1 HDPE 2 BASE PLATE 1 HDPE 9 SUPPORT BAR 1 SPPS
3 WASHER 1 SS400 3 WASHER 1 SS400 10 OPERATING BAR 1 SPPS
4 O-RING 1 NBR 4 O-RING 1 NBR 11 FIXED HANDLE 1 -
5 RUBBER SEAL 1 NEOPRENE 5 RUBBER SEAL 1 NEOPRENE 12 THRUST BEARING 1 SS400
6 TOP PLATE 1 HOPE 6 TOP PLATE 1 HDPE 13 HEX.NUT 1 SWO
7 O-RING 1 NBR 7 O-RING 1 NBR 14 HEX.NUT 1 SWO
8 SUPPORT BAR 1 STPG
9 OPERATING HANDLE 1 SPPS
10 FIXED HANDLE 1 SPPS
DIMENSION Unit : mm

11 THRUST BEARING 1 - φI.D φH

N.D L L1 L2 L3 C B REMARK
12 HEX.NUT 1 SS400 #160 #80 ETC1. ETC2. #160 #80 ETC1. ETC2.
13 SPRING WAHSER 1 SWO 350A 284.2 317.6 323.6 - 278.7 312 315.6 - 454 130 188 136 300 350
400A 325.4 363.6 374.4 - 319.5 357.6 368.6 - 454 130 188 136 300 350
450A - 409.6 425.2 - - - 419.2 - 454 130 188 136 300 350
DIMENSION Unit : mm 500A - 455.6 476 - - - 468 - 454 130 188 136 300 350
φI.D φH 550A - - 526.8 - - - 518.8 - 454 130 188 136 300 350
N.D φO.D L L1 L2 L3 C B REMARK 600A - - 577.6 - - - 569 - 454 130 188 136 300 350
#160 #80 ETC1. ETC2. #160 #80 ETC1. ETC2.
200A 216.3 168.3 190.0 184.3 193 163.3 184.4 179.3 188 387 77 188 136 350 300 650A - - 628.4 - - - 619.4 - 454 130 188 136 300 350
250A 267.4 210.2 237.2 235.4 247 204.8 230.8 230.3 242.9 387 77 188 144 350 300 700A - - 679.2 667 - - 670.2 658 454 130 188 136 300 350
300A 318.5 283.7 283.7 286.5 299 246.4 277.2 278.7 294 387 77 188 144 350 300 750A - - 736.6 - - - 727.1 - 454 130 188 136 300 350

06 07
 gshightecher.coreasme.com
GS HIGH TECHER

SEA CONNECTION PIPE PLUG <FIG2-1> SEA CONNECTION PIPE PLUG <FIG1-2>
OPERATING HANDLE D-TYPE COVER E-TYPE
5
A

DIMENSION Unit : mm 1 2 3

N.D φG φE REMARK
8 9 Ø 40 31 45

N.D
4
Ø 50 41 55
6
Ø 100 91 105 C C

B
1
9 HEA NUT, M3 SUS304 1
5 8 ROUND HEAD BOLT, M3 x 13L SUS304 1
7 LOOK NUT, M10 SS400 1
3 6 OPERATING HANDLE SS400 1
4 5 SUPPORT BAR, 10A x SOH #40 STPG370 1
2
4 RUBBER SEAL EPDM 1
3 TOP PLATE SS400 1
7
2 BASE PLATE SS400 1 MATERIAL Unit : mm
ØG
ØE 1 SHAFT, Ø12 x 205L S45C 1 No. Name of part Q’ty Material
1 ALUMINUM 1 AL5083
2 WOOD 1 POLYWOOD
3 GASKET 1 NEOPRENE
4 EYENUT 4 SUS304
SEA CONNECTION PIPE PLUG <FIG2-2> 5 BOLT 16~24 SUS304
INSENT F-TYPE Notes : 1. The cover are laminated neoplene sheet and rubber sheet.
2. Loop are attached for secure safty and sink the blanks to sea chest area.
3. For secure safty. 40M ropes are provided.
4. APLICATION FOR 200A and above size

DIMENSION Unit : mm

N.D PIPE O.D A B C

ØD ØD
200 216.3 475 500 150
250 267.4 530 560 180
A

300 318.5 580 610 210

B°
Ø5.5 THRU Ø5.5 THRU 350 355.6 615 650 240
400 406.4 665 700 280
L

B°
DIMENSION Unit : mm
L

450 457.2 720 755 310

500 508.0 770 810 350
TYPE φD A B° L PIPE SIZE
600 609.6 930 980 450
15 6 20 30
A 700 711.2 1030 1090 500
30 8 20 40 Ø5L : 200
800 812.8 1130 1200 550
B 40 8 35.5 50
900 914.4 1235 1315 600
1000 1016.0 1335 1425 700
1400 1412.0 1735 1845 1100
Notes : ‘B’Type is as for hole size

08 09
 gshightecher.coreasme.com
GS HIGH TECHER

SEA CONNECTION PIPE PLUG <FIG2-1> SEA CONNECTION PIPE PLUG <FIG1-2>
OPERATING HANDLE D-TYPE COVER E-TYPE
5
A

DIMENSION Unit : mm 1 2 3

N.D φG φE REMARK
8 9 Ø 40 31 45

N.D
4
Ø 50 41 55
6
Ø 100 91 105 C C

B
1
9 HEA NUT, M3 SUS304 1
5 8 ROUND HEAD BOLT, M3 x 13L SUS304 1
7 LOOK NUT, M10 SS400 1
3 6 OPERATING HANDLE SS400 1
4 5 SUPPORT BAR, 10A x SOH #40 STPG370 1
2
4 RUBBER SEAL EPDM 1
3 TOP PLATE SS400 1
7
2 BASE PLATE SS400 1 MATERIAL Unit : mm
ØG
ØE 1 SHAFT, Ø12 x 205L S45C 1 No. Name of part Q’ty Material
1 ALUMINUM 1 AL5083
2 WOOD 1 POLYWOOD
3 GASKET 1 NEOPRENE
4 EYENUT 4 SUS304
SEA CONNECTION PIPE PLUG <FIG2-2> 5 BOLT 16~24 SUS304
INSENT F-TYPE Notes : 1. The cover are laminated neoplene sheet and rubber sheet.
2. Loop are attached for secure safty and sink the blanks to sea chest area.
3. For secure safty. 40M ropes are provided.
4. APLICATION FOR 200A and above size

DIMENSION Unit : mm

N.D PIPE O.D A B C

ØD ØD
200 216.3 475 500 150
250 267.4 530 560 180
A

300 318.5 580 610 210

B°
Ø5.5 THRU Ø5.5 THRU 350 355.6 615 650 240
400 406.4 665 700 280
L

B°
DIMENSION Unit : mm
L

450 457.2 720 755 310

500 508.0 770 810 350
TYPE φD A B° L PIPE SIZE
600 609.6 930 980 450
15 6 20 30
A 700 711.2 1030 1090 500
30 8 20 40 Ø5L : 200
800 812.8 1130 1200 550
B 40 8 35.5 50
900 914.4 1235 1315 600
1000 1016.0 1335 1425 700
1400 1412.0 1735 1845 1100
Notes : ‘B’Type is as for hole size

08 09
 gshightecher.coreasme.com
GS HIGH TECHER

HOOK FOR BLANKING COVER FOR BLANK SUPPORT FOR HOOK

15
L

1
C
A

4
B

15
3
A

4 2
2 3 1

MATERIAL Unit : mm MATERIAL Unit : mm

ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK
1 STUDDING BOLT SUS304 1 M16 1 TUBE Ø27 x 3T SUS304 1
2 M16 WING NUT SUS304 1 2 M20 THIN NUT SUS304 1
3 PARKING RETAINER SUS304 1 Ø20.5 3 M5 x 15 WRENCH BOLT SUS304 1 M16
4 NBR WASHER NBR 1 Ø16.5 4 END PLATE SUS304 1 80 x 80 x 3T

DIMENSION Unit : mm DIMENSION Unit : mm

NAME N.D A B C Q’TY NAME N.D L A Q’TY REMARK

200 300 58 R30 2 200 200 200 2
250 300 58 R30 2 250 250 200 2
300 300 58 R30 2 300 300 200 2
350 300 58 R30 2 350 350 200 2
400 300 58 R30 2 400 400 200 2
450 300 58 R30 2 FIXING 450 450 200 2
J-BOLT 500 300 58 R30 2 JACK 500 500 200 2
600 400 58 R30 2 600 600 200 2
700 400 58 R30 4 700 700 200 4
800 400 58 R30 4 800 800 200 4
900 400 58 R30 2 900 900 200 4
1000 500 58 R30 4 1000 1000 200 4
1400 500 58 R30 4 1400 1400 200 4

10 11
 gshightecher.coreasme.com
GS HIGH TECHER

HOOK FOR BLANKING COVER FOR BLANK SUPPORT FOR HOOK

15
L

1
C
A

4
B

15
3
A

4 2
2 3 1

MATERIAL Unit : mm MATERIAL Unit : mm

ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK
1 STUDDING BOLT SUS304 1 M16 1 TUBE Ø27 x 3T SUS304 1
2 M16 WING NUT SUS304 1 2 M20 THIN NUT SUS304 1
3 PARKING RETAINER SUS304 1 Ø20.5 3 M5 x 15 WRENCH BOLT SUS304 1 M16
4 NBR WASHER NBR 1 Ø16.5 4 END PLATE SUS304 1 80 x 80 x 3T

DIMENSION Unit : mm DIMENSION Unit : mm

NAME N.D A B C Q’TY NAME N.D L A Q’TY REMARK

200 300 58 R30 2 200 200 200 2
250 300 58 R30 2 250 250 200 2
300 300 58 R30 2 300 300 200 2
350 300 58 R30 2 350 350 200 2
400 300 58 R30 2 400 400 200 2
450 300 58 R30 2 FIXING 450 450 200 2
J-BOLT 500 300 58 R30 2 JACK 500 500 200 2
600 400 58 R30 2 600 600 200 2
700 400 58 R30 4 700 700 200 4
800 400 58 R30 4 800 800 200 4
900 400 58 R30 2 900 900 200 4
1000 500 58 R30 4 1000 1000 200 4
1400 500 58 R30 4 1400 1400 200 4

10 11
 gshightecher.coreasme.com
GS HIGH TECHER

Sea Chest Hull Aperture Blanks Sea Chest Hull Aperture Blanks
Magnectic Blanket G1 – TYPE General Blanket TYPE G2 – TYPE

"sheet"NEOPLENE RUBBER
"sheet"NEOPLENE RUBBER

2 3
2 3
Breath

Breath
4 4

Length 1 Length 1
Peak Peak

MATERIAL Unit : mm MATERIAL Unit : mm

No. Name of part Q’ty Material No. Name of part Q’ty Material
1 LOOP 4 SUS304 1 LOOP 4 SUS304
2 COVER 1 NEOPLENE (6mm±0.5) 2 COVER 1 NEOPLENE (6mm±0.5)
3 BASE 1 RUBBER (1.6mm±0.5) 3 BASE 1 RUBBER (1.6mm±0.5)
4 SUPPORT 1 4 SUPPORT 1
5 MAGNETIC 12 3500 GAUSS 50 x 20 x 5mm

DIMENSION Unit : mm
DIMENSION Unit : mm
NO PEAK BREATH LENGTH Q’TY
NO PEAK BREATH LENGTH Q’TY 1 2950 1860 1470
1 4600 2700 4200 2 2500 1900 2000
2 4400 2700 4000 3 2400 2900 1800
3 2150 2000 1850 4 2150 2000 1850
4 2150 1800 1850 5 1500 1000 1100
5 1900 1200 1500 Notes : 1. The cover are laminated neoplene sheet and rubber sheet.
6 1700 3000 1400 2. Loop are attached for secure safty and sink the blanks to sea chest area.
7 1200 1100 800 3. For secure safty, 40M ropes are provided.

Notes : 1. The cover are laminated neoplene sheet and rubber sheet.
2. Loop are attached for weight control.
3. For secure safty, 40M ropes are provided.

12 13
 gshightecher.coreasme.com
GS HIGH TECHER

Sea Chest Hull Aperture Blanks Sea Chest Hull Aperture Blanks
Magnectic Blanket G1 – TYPE General Blanket TYPE G2 – TYPE

"sheet"NEOPLENE RUBBER
"sheet"NEOPLENE RUBBER

2 3
2 3
Breath

Breath
4 4

Length 1 Length 1
Peak Peak

MATERIAL Unit : mm MATERIAL Unit : mm

No. Name of part Q’ty Material No. Name of part Q’ty Material
1 LOOP 4 SUS304 1 LOOP 4 SUS304
2 COVER 1 NEOPLENE (6mm±0.5) 2 COVER 1 NEOPLENE (6mm±0.5)
3 BASE 1 RUBBER (1.6mm±0.5) 3 BASE 1 RUBBER (1.6mm±0.5)
4 SUPPORT 1 4 SUPPORT 1
5 MAGNETIC 12 3500 GAUSS 50 x 20 x 5mm

DIMENSION Unit : mm
DIMENSION Unit : mm
NO PEAK BREATH LENGTH Q’TY
NO PEAK BREATH LENGTH Q’TY 1 2950 1860 1470
1 4600 2700 4200 2 2500 1900 2000
2 4400 2700 4000 3 2400 2900 1800
3 2150 2000 1850 4 2150 2000 1850
4 2150 1800 1850 5 1500 1000 1100
5 1900 1200 1500 Notes : 1. The cover are laminated neoplene sheet and rubber sheet.
6 1700 3000 1400 2. Loop are attached for secure safty and sink the blanks to sea chest area.
7 1200 1100 800 3. For secure safty, 40M ropes are provided.

Notes : 1. The cover are laminated neoplene sheet and rubber sheet.
2. Loop are attached for weight control.
3. For secure safty, 40M ropes are provided.

12 13
 gshightecher.coreasme.com
GS HIGH TECHER

PRESSURE TANK FOR SEA CHEST COVER PRESSURE TEST EQUIPMENT FOR APERTURE BLANK

2 5

6 7 8

EST EST
4
LE LE
A CH RE HO A CH RE HO
SE R TU SE R TU
3
5

APE APE
9

SEA CHEST

VIEW "A"-"A"

G-TYPE BLANK FOR HULL APERTURE OF SEA CHEST

MATERIAL Unit : mm

ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK

MATERIAL Unit : mm
1 PRESSURE TANK SS400 1
ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK 2 CIRCULAR GLASS W / FRAME SS400 2 10t x Ø350(CLEAR)
- - - - -
4 GRATING SS400 2 600 x 800 (OUTSIDE)
4 GRATING SS400 2 600 x 800 (OUTSIDE)
5 STEP SS400 6 200 x 400
6 FLANGE W / PIPE (50A) SS400 1 JIS 5K
7 FLANGE W / PIPE (150A) SS400 1 JIS 5K
8 FLANGE W / PIPE (200A) SS400 1 JIS 5K
9 FLANGE W / PIPE (400A) SS400 1 JIS 5K

14 15
 gshightecher.coreasme.com
GS HIGH TECHER

PRESSURE TANK FOR SEA CHEST COVER PRESSURE TEST EQUIPMENT FOR APERTURE BLANK

2 5

6 7 8

EST EST
4
LE LE
A CH RE HO A CH RE HO
SE R TU SE R TU
3
5

APE APE
9

SEA CHEST

VIEW "A"-"A"

G-TYPE BLANK FOR HULL APERTURE OF SEA CHEST

MATERIAL Unit : mm

ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK

MATERIAL Unit : mm
1 PRESSURE TANK SS400 1
ITEM NO. DESCRIPTION MATERIAL Q’TY REMARK 2 CIRCULAR GLASS W / FRAME SS400 2 10t x Ø350(CLEAR)
- - - - -
4 GRATING SS400 2 600 x 800 (OUTSIDE)
4 GRATING SS400 2 600 x 800 (OUTSIDE)
5 STEP SS400 6 200 x 400
6 FLANGE W / PIPE (50A) SS400 1 JIS 5K
7 FLANGE W / PIPE (150A) SS400 1 JIS 5K
8 FLANGE W / PIPE (200A) SS400 1 JIS 5K
9 FLANGE W / PIPE (400A) SS400 1 JIS 5K

14 15