0% found this document useful (0 votes)
68 views

Raspberry Pi Library

A small description on RPi library.

Uploaded by

Yashaswi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
68 views

Raspberry Pi Library

A small description on RPi library.

Uploaded by

Yashaswi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

 Menu  Cart

Search for… 

GBP Log in  Cart

Raspberry Pi Store Maker Store micro:bit Tutorials Blog

Handy Links

New Products

Sale Items

Raspberry Pi Store

The Raspberry Pi

Kits & Bundles 


SD Cards & Adapters 
Power Supplies

HATs, pHATs & GPIO 


Cases 
Camera 
Screens & Displays 
Cables 
USB Addons 
Merch

Projects

 Gaming

 Robotics

 Audio

 Programming

Turning on an LED with your Raspberry Pi's GPIO Pins


https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 1/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

One of the biggest selling points of the Raspberry Pi is its GPIO, or General Purpose Input/Output ports.
 They are the little pins sticking out of the circuit board and allow you to plug various devices into your
Raspberry Pi.  With a little programming, you can then control them or detect what they are doing.

In this tutorial I am going to show you how to light an LED.  In addition to your Raspberry Pi running
Raspbian, what you will need is:

A Breadboard 

An LED 

A 330 ohm resistor 

Two Male-Female jumper wires

You can get all these, and more, in the £5 CamJam EduKit  from The Pi Hut, which teaches you more
about LEDs, buzzers and switches, and includes all the hardware and eight well-written worksheets about
using the GPIO pins on your Raspberry Pi.

The Breadboard
The breadboard is a way of connecting electronic components to each other without having to solder them
together. They are often used to test a circuit design before creating a Printed Circuit Board (PCB).

The holes on the breadboard are connected in a pattern.

With the breadboard in the CamJam EduKit, the top row of holes are all connected together – marked with
red dots. And so are the second row of holes – marked with blue dots. The same goes for the two rows of
holes at the bottom of the breadboard.

In the middle, the columns of wires are connected together with a break in the middle. So, for example, all
the green holes marked are connected together, but they are not connected to the yellow holes, nor the
purple ones. Therefore, any wire you poke into the green holes will be connected to other wires poked into
the other green holes.

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 2/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

The LED
When you pick up LED stands for Light Emitting Diode, and glows when electricity is passed through it.
the LED, you will
notice that one leg
is longer than the
other. The longer
leg (known as the ‘anode’), is always connected to the positive supply of the circuit. The shorter leg (known
as the ‘cathode’) is connected to the negative side of the power supply, known as ‘ground’.

LEDs will only work if power is supplied the correct way round (i.e. if the ‘polarity’ is correct). You will not
break the LEDs if you connect them the wrong way round – they will just not light. If you nd that they do
not light in your circuit, it may be because they have been connected the wrong way round.

The Resistor
You must ALWAYS use resistors to connect LEDs up to the GPIO pins of the Raspberry Pi. The Raspberry
Pi can only supply a small current (about 60mA). The LEDs will want to draw more, and if allowed to they
will burn out the Raspberry Pi. Therefore putting the resistors in the circuit will ensure that only this
small current will ow and the Raspberry Pi will not be damaged.

Resistors are a way of limiting the amount of electricity going through a circuit; speci cally, they limit the
amount of ‘current’ that is allowed to ow. The measure of resistance is called the Ohm (Ω), and the larger
the resistance, the more it limits the current. The value of a resistor is marked with coloured bands along
the length of the resistor body.

You will be using a 330Ω resistor. You can identify the 330Ω resistors by the colour bands along the body.
The colour coding will depend on how many bands are on the resistors supplied:

If there are four colour bands, they will be Orange, Orange, Brown, and then Gold.

If there are ve bands, then the colours will be Orange, Orange, Black, Black, Brown.

It does not matter which way round you connect the resistors. Current ows in both ways through them.

Jumper Wires
Jumper wires are used on breadboards to ‘jump’ from one connection to another. The
ones you will be using in this circuit have di erent connectors on each end. The end
with the ‘pin’ will go into the Breadboard. The end with the piece of plastic with a hole
in it will go onto the Raspberry Pi’s GPIO pins.

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 3/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

The Raspberry Pi's GPIO Pins 


GPIO stands for General Purpose Input Output. It is a way the Raspberry Pi can control and monitor the
outside world by being connected to electronic circuits. The Raspberry Pi is able to control LEDs, turning
them on or o , or motors, or many other things. It is also able to detect whether a switch has been
pressed, or temperature, or light. In the CamJam EduKit you will learn to control LEDs and a buzzer, and
detect when a button has been pressed. The diagram below left shows the pin layout for a Raspberry Pi
Models A and B (Rev 2 - the original Rev 1 Pi is slightly di erent), looking at the Raspberry Pi with the pins
in the top right corner. The new 40 pin Raspberry Pi’s shares exactly the same layout of pins for the top 13
rows of GPIO pins.

Building the Circuit


The circuit consists of a power supply (the Raspberry Pi), an LED that lights when the power is applied, and
a resistor to limit the current that can ow through the circuit.

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 4/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

You will be using one of the ‘ground’ (GND) pins to act like the ‘negative’ or 0 volt ends of a battery. The
‘positive’ end of the battery will be provided by a GPIO pin. Here we will be using pin 18.  When they are
‘taken high’, which means it outputs 3.3 volts, the LED will light. Now take a look at the circuit diagram
below.

You should turn your Raspberry Pi o for the next bit, just in case you accidentally short something out.

Use one of the jumper wires to connect a ground pin to the rail, marked with blue, on the
breadboard. The female end goes on the Raspberry Pi's pin, and the male end goes into a hole on the
breadboard.

Then connect the resistor from the same row on the breadboard to a column on the breadboard, as
shown above.

Next, push the LEDs legs into the breadboard, with the long leg (with the kink) on the right.

Lastly, complete the circuit by connecting pin 18 to the right hand leg of the LED. This is shown here
with the orange wire.

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 5/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

The Code
You are now ready to write some code to switch the LED on.  Turn on your Raspberry Pi and open the
terminal window.

Create a new text le “LED.py” by typing the following:

nano LED.py

Type in the following code:

import RPi.GPIO as GPIO


import time
GPIO.setmode(GPIO.BCM)
GPIO.setwarnings(False)
GPIO.setup(18,GPIO.OUT)
print "LED on"
GPIO.output(18,GPIO.HIGH)
time.sleep(1)
print "LED off"
GPIO.output(18,GPIO.LOW)

Once you have typed all the code and checked it, save and exit the text editor with “Ctrl + x” then “y” then
“enter”.

Running the Code


To run this code type:

sudo python LED.py

You will see the LED turn on for a second and then turn o .

If your code does not run and an error is reported, edit the code again using nano LED.py .

Explanation
So, what is happening in the code?  Let’s go through it a line at a time:

import RPi.GPIO as GPIO The rst line tells the Python interpreter (the thing
that runs the Python code) that it will be using a
‘library’ that will tell it how to work with the

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 6/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

Raspberry Pi’s GPIO pins.  A ‘library’ gives a


programming language extra commands that can
be used to do something di erent that it
previously did not know how to do.  This is like
adding a new channel to your TV so you can
watch something di erent.

Imports the Time library so that we can pause the


import time
script later on.

Each pin on the Raspberry Pi has several di erent


GPIO.setmode(GPIO.BCM) names, so you need to tell the program which
naming convention is to be used.

This tells Python not to print GPIO warning


GPIO.setwarnings(False)
messages to the screen.

This line tells the Python interpreter that pin 18 is


going to be used for outputting information,
GPIO.setup(18,GPIO.OUT)
which means you are going to be able to turn the
pin ‘on’ and ‘o ’.

print "LED on" This line prints some information to the terminal.

This turns the GPIO pin ‘on’. What this actually


means is that the pin is made to provide power of
GPIO.output(18,GPIO.HIGH)
3.3volts.  This is enough to turn the LED in our
circuit on.

time.sleep(1) Pauses the Python program for 1 second

print "LED off" This line prints some information to the terminal.

This turns the GPIO pin ‘o ’, meaning that the pin


GPIO.output(18,GPIO.LOW)
is no longer supplying any power.

And that's it! You are now able to turn an LED on and o .

Products used in this tutorial...

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 7/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

ThePiHut's Ultimate 5MM LED Kit

£6.00 GBP

ThePiHut's Ultimate Resistor Kit

£6.00 GBP

CamJam EduKit

£5.00 GBP

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 8/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

Raspberry Pi Breadboard (Half Size)

£3.00 GBP

 Share  Tweet  Pin it 14

← Older Post Newer Post →

Related Posts

How To Stream Digital TV With The Raspberry Pi TV HAT

This guide will steer you through the process of assembling, installing, con guring and operating
the Raspberry Pi T...

READ MORE

How to control your Raspberry Pi robot with a TV remote

If you’ve bought one of our a ordable EduKit Robotics kits, you’ll no doubt come to a point where
you want to advanc...

READ MORE

Control your Raspberry Pi media centre with FLIRC

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 9/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

One of the rst things you’ll need when you set up a Raspberry Pi media centre is a remote control.
Using a keyboard...

READ MORE

 Newsletter Sign up for promotions


[email protected] Subscribe

[email protected]

Subscribe

Got any questions?

Can I Cancel My order?

Has My Order Shipped Yet?

Where Is My Order?

Do You Ship To {insert country name}

How Much Is Shipping?

 Visit our support portal

Quick Links

Search

All Products

Raspberry Pi Store

Maker Store

Micro:Bit Store

FAQ

Terms & Conditions

Delivery

Privacy Statement

Policies

Terms of Service

Company Info

Get Connected

  

Copyright © 2019, The Pi Hut. Ecommerce Software by Shopify

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 10/11
24/01/2019 Turning on an LED with your Raspberry Pi's GPIO Pins | The Pi Hut

      

https://thepihut.com/blogs/raspberry-pi-tutorials/27968772-turning-on-an-led-with-your-raspberry-pis-gpio-pins 11/11

You might also like