MODEL 3022 ACCELEROMETER

SPECIFICATIONS


Piezoresistive MEMS


DC Response


Circuit Board Mountable
Low Cost

The Model 3022 is a silicon MEMS accelerometer

in a Wheatstone bridge configuration. The accelerometer is
packaged on a ceramic substrate with an epoxy sealed
ceramic cover and is designed for adhesive mounting. The
accelerometer is offered in ranges from ±2g to ±200g range
and provides a flat frequency response to minimum 2000Hz.
The silicon MEMS sensor is gas damped and incorporates
DIMENSIONS over-range stops for high-g shock protection.
For a similar accelerometer designed for bolt
mounting, see the model 3028..

FEATURES
 Adhesive Mounted
 ±0.5% Non-linearity
 Open Wheatstone Bridge
 DC Response
 Gas Damping
 Built-in Overrange Stops
 Low Power Consumption

APPLICATIONS
 Vibration & Shock Monitoring
 Motion Control
 Impact & Shock Testing
 Modal Analysis
 Embedded Applications
 Machinery

SENSOR SOLUTIONS /// Model 3022 Rev B 07/2017 Page 1

 MODEL 3022 ACCELEROMETER

PERFORMANCE SPECIFICATIONS
All values are typical at +24°C, 80Hz and 5Vdc excitation unless otherwise stated. Measurement Specialties reserves the right to update and
change these specifications without notice.

Parameters
DYNAMIC Notes
Range (g) ±2 ±5 ±10 ±20 ±50 ±100 ±200
Sensitivity (mV/g)1 8.0-20.0 6.0-15.0 3.0-6.0 1.5-3.0 0.6-1.5 0.3-0.6 0.15-0.3 @5Vdc Exc.
Frequency Response (Hz) 0-150 0-250 0-400 0-600 0-1000 0-1500 0-2000 ±5%
Natural Frequency (Hz) 700 800 1000 1500 4000 6000 8000
Non-Linearity (%FSO) ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5
Transverse Sensitivity (%) 3 3 3 3 3 3 3
Damping Ratio 0.7 0.7 0.7 0.7 0.7 0.7 0.6
Shock Limit (g) 2000 2000 5000 5000 5000 5000 5000

ELECTRICAL
Zero Acceleration Output (mV) ±25 ±25 ±25 ±25 ±25 ±25 ±25 Differential
Excitation Voltage (Vdc) 2 to 10 2 to 10 2 to 10 2 to 10 2 to 10 2 to 10 2 to 10
Input Resistance (Ω) 2500-6500 2500-6500 2500-6500 2500-6500 2500-6500 2500-6500 2500-6500
Output Resistance (Ω) 2500-6500 2500-6500 2500-6500 2500-6500 2500-6500 2500-6500 2500-6500
Insulation Resistance (MΩ) >100 >100 >100 >100 >100 >100 >100 @50Vdc
Residual Noise (µV RMS) 10 10 10 10 10 10 10 Maximum
Ground Isolation Isolated from Mounting Surface

ENVIRONMENTAL
Thermal Zero Shift (%FSO/°C) -0.09 -0.09 -0.09 -0.09 -0.09 -0.09 -0.09 Typical
Thermal Sensitivity Shift (%/°C) -0.15 -0.15 -0.15 -0.15 -0.15 -0.15 -0.15 Typical
Operating Temperature (°C) -40 to +125
Compensated Temperature (°C) Not Compensated See Note 2
Storage Temperature (°C) -40 to +125

PHYSICAL
Case Material Ceramic
Weight (grams) 3.1
Mounting Adhesive or solder
1
Output is ratiometric to excitation voltage
2
Order model 3022-XXX-10254 for temperature compensation resistor values included in the calibration certificate.

Optional accessories: 121 Three Channel DC Differential Amplifier

140 Auto-Zero Inline Amplifier

The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this
information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the
right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the
suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or
circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different
applications. All operating parameters must be validated for each customer application by customer’s technical experts. Measurement Specialties, Inc. does not
convey any license under its patent rights nor the rights of others.

SENSOR SOLUTIONS /// Model 3022 Rev B 07/2017 Page 2

MODEL 3022 ACCELEROMETER

ORDERING INFORMATION
PART NUMBERING Model Number+Range+Electrical Connection

3022-GGG-P
l l
l l_____Electrical Connection (P=pins, N=solder pads)
l___________Range (010 is 10g)

Example: 3022-010-P
Model 3022, 10g, Pins

ASIA
NORTH AMERICA EUROPE Measurement Specialties (China), Ltd.,
Measurement Specialties, Inc., MEAS France SAS a TE Connectivity Company
a TE Connectivity Company a TE Connectivity Company Sales and Customer Service
Tel: 800-522-6752 Tel: 800-440-5100 Tel: 0400-820-6015
Email: [email protected] Email : [email protected] Email: [email protected]

TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
© 2015 TE Connectivity Ltd. family of companies All Rights Reserved.

SENSOR SOLUTIONS /// Model 3022 Rev B 07/2017 Page 3