CCNA Routing and Switching: © 2008 Cisco Systems, Inc. All Rights Reserved. Cisco Confidential Presentation - ID

STP
CCNA Routing and Switching
Presentation_ID © 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential 1
Redundancy
 Achieving such a goal requires extremely reliable networks.

 Reliability in networks is achieved by reliable equipment and by
designing networks that are tolerant to failures and faults.
 The network is designed to reconverge rapidly so that the fault is
bypassed.
 Fault tolerance is achieved by redundancy.
 Redundancy means to be in excess or exceeding what is usual and
natural.
Redundant topologies
One Bridge Redundant Bridges
 A network of roads is a global example of a redundant

topology.
 If one road is closed for repair there is likely an alternate
route to the destination
Types of Traffic
Unknown Unicast
Types of traffic (Layer 2 perspective)
 Known Unicast: Destination addresses are in Switch Tables
 Unknown Unicast: Destination addresses are not in Switch Tables
 Multicast: Traffic sent to a group of addresses
 Broadcast: Traffic forwarded out all interfaces except incoming
interface.
Redundant switched topologies
 Switches learn the MAC addresses of devices on their ports so that data
can be properly forwarded to the destination.
 Remember: switches use the Source MAC address to learn where the
devices are, and enters this information into their MAC address tables.
 Switches will flood frames for unknown destinations until they learn the MAC
addresses of the devices.
 Broadcasts and multicasts are also flooded. (Unless switch is doing Multicast
Snooping or IGMP)
 A redundant switched topology may (STP disabled) cause broadcast storms,
multiple frame copies, and MAC address table instability problems.
Broadcast Storm
Broadcast storm: “A state in which a
message that has been broadcast across
a network results in even more
responses, and each response results in
still more responses in a snowball effect.”
www.webopedia.com
A broadcast storm because Spanning Tree Protocol is not enabled:

 Broadcasts and multicasts can cause problems in a switched network.
 If Host X sends a broadcast, like an ARP request for the Layer 2 address of the router,
then Switch A will forward the broadcast out all ports.
 Switch B, being on the same segment, also forwards all broadcasts.
 Switch B sees all the broadcasts that Switch A forwarded and Switch A sees all the
broadcasts that Switch B forwarded.
 Switch A sees the broadcasts and forwards them.
 Switch B sees the broadcasts and forwards them.
 The switches continue to propagate broadcast traffic over and over.
 This is called a broadcast storm.
Multiple frame transmissions
 In a redundant switched network it is possible for an end device to

receive multiple frames.
 Assumptions:
• Spanning Tree Protocol is not enabled
• MAC address of Router Y has been timed out by both switches.
• Host X still has the MAC address of Router Y in its ARP cache
 Host X sends a unicast frame to Router Y.
Let’s try it
 We will connect two switches with two paths

• S1 Fa0/21 <-> Fa0/21 S2
• S1 Fa0/22 <-> Fa0/22 S2
 Connect multiple computers

 Disable Spanning Tree
• S1,S2(config)# no spanning-tree vlan 1
Redundant topology and spanning tree
 Unlike IP, in the Layer 2 header there is no Time

To Live (TTL).
 The solution is to allow physical loops
(redundant physical connections) but create
a loop free logical topology.
 The loop free logical topology created is
called a tree.
 This topology is a star or extended star logical
topology, the spanning tree of the network.
Redundant topology and spanning tree
 It is a spanning tree because all devices in the network are reachable or

spanned.
 The algorithm used to create this loop free logical topology is the
spanning-tree algorithm.
 This algorithm can take a “relatively” long time to converge.
 A new algorithm called the rapid spanning-tree algorithm is being
introduced to reduce the time for a network to compute a loop free
logical topology. (later)
Spanning-Tree Protocol (STP)
We will see how this

works in a moment.
 Shortest path is based on cumulative link costs.
 Link costs are based on the speed of the link.
 The Spanning-Tree Protocol establishes a root node, called the root bridge.
 The Spanning-Tree Protocol constructs a topology that has one path for reaching
every network node.
 The resulting tree originates from the root bridge.
 Redundant links that are not part of the shortest path tree are blocked.
Spanning-Tree Protocol (STP)
BPDU
 It is because certain paths are blocked that a loop free topology is

possible.
 Data frames received on blocked links are dropped.
 The Spanning-Tree Protocol requires network devices to exchange
messages to prevent bridging loops, called Bridge Protocol Data Unit
(BPDU). .
 Links that will cause a loop are put into a blocking state.
 BPDUs continue to be received on blocked ports.
 This ensures that if an active path or device fails, a new spanning tree can be
calculated.
Spanning-Tree
Protocol (STP)
BPDUs contain enough information so that all switches can do the

following:
 Select a single switch that will act as the root of the spanning tree
 Calculate the shortest path from itself to the root switch
 Designate one of the switches as the closest one to the root, for
each LAN segment. This bridge is called the “designated switch”.
• The designated switch handles all communication from that LAN
towards the root bridge.
 Choose one of its ports as its root port, for each non-root switch.
• This is the interface that gives the best path to the root switch.
 Select ports that are part of the spanning tree, the designated ports.
Non-designated ports are blocked.
Two Key Concepts: BID and Path Cost
 STP executes an algorithm called Spanning Tree Algorithm (STA).

 STA chooses a reference point, called a root bridge, and then
determines the available paths to that reference point.
• If more than two paths exists, STA picks the best path and blocks the
rest
 STP calculations make extensive use of two key concepts in creating a
loop-free topology:
• Bridge ID
• Path Cost
Bridge ID (BID)
 Bridge ID (BID) is used to identify each bridge/switch.

 The BID is used in determining the center of the network, in respect
to STP, known as the root bridge.
 Consists of two components:
• A 2-byte Bridge Priority: Cisco switch defaults to 32,768 or 0x8000.
• A 6-byte MAC address
Bridge ID (BID)
 Bridge Priority is usually expressed in decimal format and the MAC

address in the BID is usually expressed in hexadecimal format.
 BID is used to elect a root bridge (coming)
 Lowest Bridge ID is the root.
 If all devices have the same priority, the bridge with the lowest MAC
address becomes the root bridge. (Yikes!)
Bridge ID (BID)
ALSwitch#show spanning-tree
VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 32768
Address 0003.e334.6640
Cost 19
Port 23 (FastEthernet0/23)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Address 000b.fc28.d400
Aging Time 300
Interface Port ID Designated Port ID

Name Prio.Nbr Cost Sts Cost Bridge ID Prio.Nbr
---------------- -------- --------- --- --------- -------------------- --------
Fa0/23 128.23 19 FWD 0 32768 0003.e334.6640 128.25
Path Cost
 Bridges use the concept of cost to evaluate how close they are to other
bridges.
 This will be used in the STP development of a loop-free topology .
 Originally, 802.1d defined cost as 1000/bandwidth of the link in Mbps.
• Cost of 10Mbps link = 100 or 1000/10
• Cost of 100Mbps link = 10 or 1000/100
• Cost of 1Gbps link = 1 or 1000/1000
 Running out of room for faster switches including 10 Gbps Ethernet.
Path Cost
 IEEE modified the most to use a non-linear scale with the new values of:
• 4 Mbps 250 (cost)
• 1 Gbps 4 (cost)
• 10 Gbps 2 (cost)
Path Cost
 You can modify the path cost by modifying the cost of a port.
• Switch(config-if)# spanning-tree cost value
• Exercise caution when you do this!
 BID and Path Cost are used to develop a loop-free topology .
 Coming very soon!
 But first the Four-Step STP Decision Sequence
Four-Step STP Decision Sequence
 When creating a loop-free topology, STP always uses
the same four-step decision sequence:
Four-Step decision Sequence
Step 1 - Lowest BID
Step 2 - Lowest Path Cost to Root Bridge
Step 3 - Lowest Sender BID
Step 4 - Lowest Port ID
 Bridges use Configuration BPDUs during this four-
step process.
• There is another type of BPDU known as Topology Change
Notification (TCN) BPDU (later)
Three Steps of Initial STP Convergence
 The STP algorithm uses three simple steps to converge on a loop-free
topology.
 Switches go through three steps for their initial convergence:
STP Convergence
Step 1 Elect one Root Bridge
Step 2 Elect Root Ports
Step 3 Elect Designated Ports
 All STP decisions are based on a the following predetermined
sequence:
Four-Step decision Sequence
Step 1 - Lowest BID
Step 2 - Lowest Path Cost to Root Bridge
Step 3 - Lowest Sender BID
Step 4 - Lowest Port ID
STP Convergence
Root
Bridge
Cost=19 1/1 1/2 Cost=19
Cat-A
1/1 1/1
Cat-B Cat-C
1/2 1/2
Cost=19
Step 1 Elect one
Root Bridge
 When the network first starts, all bridges are announcing a chaotic mix
of BPDUs.
 All bridges immediately begin applying the four-step sequence
decision process.
 Switches need to elect a single Root Bridge.
 Switch with the lowest BID wins!
 Note: Many texts refer to the term “highest priority” which is the
“lowest” BID value.
 This is known as the “Root War.”
Cat-A has the lowest Bridge MAC Address, so it wins the Root War!
All 3 switches have the same default Bridge Priority value of 32,768
BPDU
802.3 Header Its all done with BPDUs!
Destination: 01:80:C2:00:00:00 Mcast 802.1d Bridge group
Source: 00:D0:C0:F5:18:D1
LLC Length: 38
802.2 Logical Link Control (LLC) Header
Dest. SAP: 0x42 802.1 Bridge Spanning Tree
Source SAP: 0x42 802.1 Bridge Spanning Tree
Command: 0x03 Unnumbered Information
802.1 - Bridge Spanning Tree
Protocol Identifier: 0
Protocol Version ID: 0
Message Type: 0 Configuration Message
Flags: %00000000
Root Priority/ID: 0x8000/ 00:D0:C0:F5:18:C0
Cost Of Path To Root: 0x00000000 (0)
Bridge Priority/ID: 0x8000/ 00:D0:C0:F5:18:C0
Port Priority/ID: 0x80/ 0x1D
Message Age: 0/256 seconds (exactly 0 seconds)
Configuration
Maximum Age: BPDUs are (exactly
5120/256 seconds sent every 2 seconds by default.
20 seconds)
Hello Time: 512/256 seconds (exactly 2 seconds)
Forward Delay:
Presentation_ID
3840/256 seconds (exactly 15 seconds)
© 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential 27
 In a real network, you do not want the placement of the root bridge to rely
on the random placement of the switch with the lowest MAC address.
 A misplaced root bridge can have significant effects on your network
including less than optimum paths within the network.
 It is better to configure a switch to be the root bridge:
Switch(config)# spanning-tree [vlan vlan-list] priority priority *
 Priority
• Default = 32,768
• Range 0-65,535
• Lowest wins
Switch(config)# spanning-tree vlan 1 priority 0
2950#show spanning-tree
VLAN0001
Address 0003.e334.6640
Cost 19

Aging Time 300

---------------- -------- --------- --- --------- -------------------- --------
Fa0/23 128.23 19 FWD 0 32768 0003.e334.6640 128.25
ALSwitch#
Spanning tree 1 is executing the IEEE compatible Spanning Tree protocol

Bridge Identifier has priority 32768, address 0003.e334.6640
Configured hello time 2, max age 20, forward delay 15
We are the root of the spanning tree
Topology change flag not set, detected flag not set, changes 1
Times: hold 1, topology change 35, notification 2
hello 2, max age 20, forward delay 15
Timers: hello 0, topology change 0, notification 0
Interface Fa0/1 (port 13) in Spanning tree 1 is down

Port path cost 19, Port priority 128
Designated root has priority 32768, address 0003.e334.6640
Designated bridge has priority 32768, address 0003.e334.6640
Designated port is 13, path cost 0
Timers: message age 0, forward delay 0, hold 0
BPDU: sent 1, received 0
STP Convergence
Root
Bridge
Cost=19 1/1 1/2 Cost=19
Cat-A
1/1 1/1
Cat-B Cat-C
1/2 1/2
Cost=19
 Now that the Root War has been won, switches move on to selecting
Root Ports.
 A bridge’s Root Port is the port closest to the Root Bridge.
 Bridges use the cost to determine closeness.
 Every non-Root Bridge will select one Root Port!
 Specifically, bridges track the Root Path Cost, the cumulative cost of
all links to the Root Bridge.
Root
Bridge
Cost=19 1/1 1/2 Cost=19
Cat-A
Our Sample Topology
1/1 1/1
Cat-B Cat-C
1/2 1/2
Cost=19
Root
Bridge
Cost=19 Cost=19
Step 2 1/1 1/2
Elect Root Cat-A

BPDU BPDU
Ports Cost=0 Cost=0
BPDU BPDU
Cost=0+19=19 Cost=0+19=19
1/1 1/1
Cat-B Cat-C
1/2 1/2
Step 1 Cost=19
 Cat-A sends out BPDUs, containing a Root Path Cost of 0.

 Cat-B receives these BPDUs and adds the Path Cost of Port 1/1 to the
Root Path Cost contained in the BPDU.
Step 2
 Cat-B adds Root Path Cost 0 PLUS its Port 1/1 cost of 19 = 19
Root
Bridge
Cost=19 Cost=19
Step 2 1/1 1/2
Elect Root Cat-A

BPDU BPDU
Ports Cost=0 Cost=0
BPDU BPDU
Cost=19 Cost=19
1/1 1/1
Cat-B Cat-C
1/2 BPDU BPDU 1/2
BPDU Cost=19 Cost=19 BPDU
Cost=38 (19=19) Cost=38 (19=19)
Cost=19
Step 3
 Cat-B uses this value of 19 internally and sends BPDUs with a Root
Path Cost of 19 out Port 1/2.
Step 4
 Cat-C receives the BPDU from Cat-B, and increased the Root Path Cost
to 38 (19+19). (Same with Cat-C sending to Cat-B.)
Presentation_ID 35
© 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential
Root
Bridge
Cost=19 Cost=19
Step 2 1/1 1/2
Elect Root Cat-A

BPDU BPDU
Ports Cost=0 Cost=0
BPDU BPDU
Cost=19 Cost=19
1/1 1/1 Root
Root Port
Port
Cat-B Cat-C
1/2 1/2
BPDU BPDU
Cost=38 (19=19) Cost=38 (19=19)
Step 5 Cost=19
 Cat-B calculates that it can reach the Root Bridge at a cost of 19 via Port
1/1 as opposed to a cost of 38 via Port 1/2.
 Port 1/1 becomes the Root Port for Cat-B, the port closest to the Root
Bridge.
 Cat-C goes through a similar calculation. Note: Both Cat-B:1/2 and Cat-
C:1/2 save the best BPDU of 19 (its own).
VLAN0001
Address 0003.e334.6640
Cost 19

Aging Time 300

---------------- -------- --------- --- --------- -------------------- --------
Fa0/23 128.23 19 FWD 0 32768 0003.e334.6640 128.25
STP Convergence
Step 3 Elect
Designated
Ports
 The loop prevention part of STP becomes evident during this step, electing
designated ports.
 A Designated Port functions as the single bridge port that both sends and
receives traffic to and from that segment and the Root Bridge.
 Each segment in a bridged network has one Designated Port, chosen
based on cumulative Root Path Cost to the Root Bridge.
 The switch containing the Designated Port is referred to as the Designated
Bridge for that segment.
 To locate Designated Ports, lets take a look at each segment.
 Root Path Cost, the cumulative cost of all links to the Root Bridge.
Root
Root Path Cost = 0 Bridge Root Path Cost = 0
Cost=19 1/1 1/2 Cost=19
Segment 1 Segment 2
Cat-A
Step 3 Elect
Designated Ports
Root Path Cost = 19 Root Path Cost = 19

1/1 Root Port Root Port 1/1
Cat-B Cat-C
1/2 1/2
Segment 3
Cost=19
 Segment 1: Cat-A:1/1 has a Root Path Cost = 0 (after all it has the Root Bridge)
and Cat-B:1/1 has a Root Path Cost = 19.
 Segment 2: Cat-A:1/2 has a Root Path Cost = 0 (after all it has the Root Bridge)
and Cat-C:1/1 has a Root Path Cost = 19.
 Segment 3: Cat-B:1/2 has a Root Path Cost = 19 and Cat-C:1/2 has a Root
Path Cost = 19. It’s a tie!
Root
Cost=19 1/1 1/2 Cost=19
Segment 1 Segment 2
Cat-A
Designated Port Designated Port
Step 3 Elect
Designated Ports

Cat-B Cat-C
1/2 1/2
Segment 3
Cost=19
Segment 1
 Because Cat-A:1/1 has the lower Root Path Cost it becomes the
Designate Port for Segment 1.
Segment 2
 Because Cat-A:1/2 has the lower Root Path Cost it becomes the
Designate Port for Segment 2.
Root
Cost=19 1/1 1/2 Cost=19
Segment 1 Segment 2
Cat-A

Cat-B Cat-C
1/2 1/2
Segment 3
Cost=19
Segment 3
 Both Cat-B and Cat-C have a Root Path Cost of 19, a tie!
 When faced with a tie (or any other determination) STP always uses the four-
step decision process:
Root
Cost=19 1/1 1/2 Cost=19
Segment 1 Segment 2
Cat-A

Cat-B 32,768.CC-CC-CC-CC-CC-CC Cat-C

1/2 32,768.BB-BB-BB-BB-BB-BB 1/2
Designated Port Segment 3 Non-Designated Port
Cost=19
Segment 3 (continued)
 1) All three switches agree that Cat-A is the Root Bridge, so this is a tie.
 2) Root Path Cost for both is 19, also a tie.
 3) The sender’s BID is lower on Cat-B, than Cat-C, so Cat-B:1/2 becomes the
Designated Port for Segment 3.
 Cat-C:1/2 therefore becomes the non-Designated Port for Segment 3.
We will first only look at switch ports
that have connections to other switches.
Stages of spanning-tree port states
Stages of spanning-tree port states
 Time is required for (BPDU) protocol information to propagate throughout a

switched network.
 Topology changes in one part of a network are not instantly known in other parts
of the network.
 There is propagation delay.
 A switch should not change a port state from inactive (Blocking) to active
(Forwarding) immediately, as this may cause data loops.
 Each port on a switch that is using the Spanning-Tree Protocol has one of five
states,
STP Port States
 In the blocking state, ports can only receive BPDUs.

• Data frames are discarded and no addresses can be learned.
• It may take up to 20 seconds to change from this state.
 Ports go from the blocked state to the listening state.
• Switch determines if there are any other paths to the root bridge.
• The path that is not the least cost path to the root bridge goes back to
the blocked state.
• The listening period is called the forward delay and lasts for 15 seconds.
• In the listening state, user data is not being forwarded and MAC addresses
are not being learned.
• BPDUs are still processed.
Presentation_ID 47
© 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential
STP Port States
 Ports transition from the listening to the learning state.

• In this state user data is not forwarded, but MAC addresses are
learned from any traffic that is seen.
• The learning state lasts for 15 seconds and is also called the
forward delay.
STP Port States
 A port goes from the learning state to the forwarding state.

• In this state user data is forwarded and MAC addresses continue to be
learned.
 Remember – A switch port is allowed to transition to the Forwarding
state only if no redundant links (loops) are detected and if the port has
the best path to the Root Bridge as the Root Port or Designated Port.
Access ports
 When a device is connected to a port, the port normally moves from Blocking
State to Listening state, for 15 seconds.
 When the Forward Delay timer expires, the port enters the Learning state, for 15
seconds.
 When the Forward Delay timer expires a second time, the port is transitioned to
the Forwarding or Blocking state.
 This 30 seconds delay can cause a problem with computers asking for an IP
address (DHCP) before the switch port has transitioned to Forwarding State.
 This causes the DHCP to fail, and the host to configure a default IP address.
Access ports
 When PortFast is enabled on a switch or trunk port, the port is

immediately transitioned to the Forwarding state.
 As soon as the switch detects the link, the port is transitioned to the
Forwarding state (less than 2 seconds after the cable is plugged in).
 This should only be enabled on switch ports where there are only hosts
and not any switches.
Switch(config-if)# spanning-tree portfast
ALSwitch#show spanning-tree (Connecting a host without Portfast on)
VLAN0001
Address 0003.e334.6640
Cost 19

Aging Time 15

---------------- -------- --------- --- --------- -------------------- -------
Fa0/8 128.8 19 LIS 19 32769 000b.fc28.d400 128.8
Fa0/23 128.23 19 FWD 0 32768 0003.e334.6640 128.25
---------------- -------- --------- --- --------- -------------------- -------
Fa0/8 128.8 19 LRN 19 32769 000b.fc28.d400 128.8
Fa0/23 128.23 19 FWD 0 32768 0003.e334.6640 128.25
---------------- -------- --------- --- --------- -------------------- -------
Fa0/8 128.8 19 FWD 19 32769 000b.fc28.d400 128.8
Fa0/23 128.23 19 FWD 0 32768 0003.e334.6640 128.25
Example of redundant links
Not seeing
BPDU from
Ages out
Cat-B
X Fails BPDU and
goes into
Hub Listening
mode
 Cat-B:1/2 fails.
 Cat-C has no immediate notification because it’s still receiving a link
from the hub.
 Cat-C notices it is not receiving BPDUs from Cat-B.
 20 seconds (max age) after the failure, Cat-C ages out the BPDU that
lists Cat-B as having the DP for Hub
segment 3.
 This causes Cat-C:1/2 to transition into the Listing state (15
seconds) in an effort to become the DP.
X Fails
Forwarding
ListeningMode
Mode
Hub
 Because Cat-C:1/2 now offers the most attractive access from the Root
Bridge to this link, it eventually transitions to Learning State (15
seconds), then all the way into Forwarding mode.
 In practice this will take 50 seconds (20 max age + 15 Listening + 15
Learning) for Cat-C:1/2 to take over after the failure of Cat-B:1/2.
Hub
Port Cost/Port ID
0/2
Blocking
X
0/1
Forwarding
Assume path cost and port priorities are
default (32). Port ID used in this case.
Port 0/1 would forward because it’s the
lower than Port 0/2.
 If the path cost and bridge IDs are equal (as in the case of parallel links),
the switch goes to the port priority as a tiebreaker.
 Lowest port priority wins (all ports set to 32).
 You can set the priority from 0 – 63.
 If all ports have the same priority, the port with the lowest port number
forwards frames.
Rapid Spanning Tree Protocol (RSTP)
Rapid Spanning Tree Protocol (RSTP)
 The Rapid Spanning-Tree Protocol is defined in the IEEE 802.1w LAN standard.
 The standard and protocol introduce the following:
• Clarification of port states and roles
• Definition of a set of link types that can go to forwarding state rapidly
• Concept of allowing switches, in a converged network, to generate their own
BPDUs rather than relaying root bridge BPDUs
 The “blocked” state of a port has been renamed as the “discarding” state.
RSTP Link Types
 Link types have been defined as point-to-point, edge-type, and shared.

 These changes allow failure of links in switched network to be learned rapidly.
 Point-to-point links and edge-type links can go to the forwarding state
immediately.
 Network convergence does not need to be any longer than 15 seconds with
these changes.
 The Rapid Spanning-Tree Protocol, IEEE 802.1w, will eventually replace the
Spanning-Tree Protocol, IEEE 802.1D
RSTP Port States

CCNA Routing and Switching: © 2008 Cisco Systems, Inc. All Rights Reserved. Cisco Confidential Presentation - ID

Uploaded by

Copyright:

Available Formats

CCNA Routing and Switching: © 2008 Cisco Systems, Inc. All Rights Reserved. Cisco Confidential Presentation - ID

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CCNA Routing and Switching: © 2008 Cisco Systems, Inc. All Rights Reserved. Cisco Confidential Presentation - ID

Uploaded by

Copyright:

Available Formats

STP

CCNA Routing and Switching

 Achieving such a goal requires extremely reliable networks.

One Bridge Redundant Bridges

 A network of roads is a global example of a redundant

A broadcast storm because Spanning Tree Protocol is not enabled:

 In a redundant switched network it is possible for an end device to

 We will connect two switches with two paths

 Connect multiple computers

 Unlike IP, in the Layer 2 header there is no Time

 It is a spanning tree because all devices in the network are reachable or

We will see how this

 It is because certain paths are blocked that a loop free topology is

BPDUs contain enough information so that all switches can do the

 STP executes an algorithm called Spanning Tree Algorithm (STA).

 Bridge ID (BID) is used to identify each bridge/switch.

 Bridge Priority is usually expressed in decimal format and the MAC

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Interface Port ID Designated Port ID

Switch(config)# spanning-tree [vlan vlan-list] priority priority *

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Interface Port ID Designated Port ID

Spanning tree 1 is executing the IEEE compatible Spanning Tree protocol

Interface Fa0/1 (port 13) in Spanning tree 1 is down

Elect Root Cat-A

 Cat-A sends out BPDUs, containing a Root Path Cost of 0.

Elect Root Cat-A

Elect Root Cat-A

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Interface Port ID Designated Port ID

Root Path Cost = 19 Root Path Cost = 19

Root Path Cost = 19 Root Path Cost = 19

Root Path Cost = 19 Root Path Cost = 19

Root Path Cost = 19 Root Path Cost = 19

Cat-B 32,768.CC-CC-CC-CC-CC-CC Cat-C

 Time is required for (BPDU) protocol information to propagate throughout a

 In the blocking state, ports can only receive BPDUs.

 Ports transition from the listening to the learning state.

 A port goes from the learning state to the forwarding state.

 When PortFast is enabled on a switch or trunk port, the port is

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Interface Port ID Designated Port ID

 Link types have been defined as point-to-point, edge-type, and shared.

You might also like