Dec

21,2015

BS110401050 [email protected] [email protected] AKMP01

Final-Term Papers Solved MCQs CS501- Advance Computer Architecture

1. What is the instruction length of the FALCON-A processor?

 8 bits
 16 bits PG # 91
 32 bits
 64 bits

2. What is the working of Processor Status Word (PSW)?

 To hold the current status of the processor. PG # 25

 To hold the address of the current process
 To hold the instruction that the computer is currently processing
 To hold the address of the next instruction in memory that is to be executed

3. What functionality is performed by the instruction “str R8, 34” of SRC?

 it will load the register R8 with the contents of the memory location M [PC+34]
 It will load the register R8 with the relative address itself (PC+34).
 It will store the register R8 contents to the memory location M [PC+34] PG # 48
 No operation
4. FALCON-A processor bus has 16 lines or is 16-bits wide while that of SRC is __________ wide.

 8-bits
 24-bits
 32-bits PG # 157
 64-bits

5. op<4..0>:= IR<15..11>:
The above RTL instruction presents the __________ of the FALCON-A Instructions.

 operation code field PG # 105

 target register field
 operand or address index
 second operand

6. Which one of the following register holds the address of the next instruction to be executed?

 Accumulator
 Address Mask
 Instruction Register
 Program Counter PG # 151

7. Which one of the following register holds the instruction that is being executed?

 Accumulator
 Address Mask
 Instruction Register PG # 152
 Program Counter

8. ________ operation is required to change the processor‟s state to a known, defined value.

 Change
 Reset PG # 194
 Update
 Halt
9. Type B format of SRC uses -----------instructions

 Two
 Three PG # 47
 Four
 Five

10. ________ control signal enable the CON circuitry to operate, and instruct it to check for the appropriate
condition (whether it is branch if zero, or branch if not equal to zero, etc.)

 ECON
 BCON
 LCON PG # 184
 VCON

11. In which one of the following addressing modes, data is the part of the instruction itself, and so there is no need
of address calculation?

 Direct Addressing Mode

 Immediate addressing mode PG # 40
 Indirect Addressing Mode
 Register (Direct) Addressing Mode

12. ___________ is a technique in which some of the CPU‟s address lines forming an input to the address decoder
are ignored.

 Partial decoding PG # 255

 Full encoding
 Partial multiplexing
 Half encoding
 13. Every time you press a key, an interrupt is generated; this is an example of ___________.

 Hardware interrupt
 Compile time error
 Run time error
 Internal interrupt

14. ___________ refers to the situation in which all I/O operations are performed under the direct control of a
program running on the CPU.

 Direct memory access

 Virtual memory
 Partial decoding
 Programmed I/O PG # 268

15. CPU can exchange data with a peripheral device using _________ technique.

 Memory Contention
 Direct Memory Access PG # 269
 Pre-fetching
 Pipelining

There are three main techniques using which a CPU can exchange data with a peripheral device, namely
• Programmed I/O
• Interrupt driven I/O
• Direct Memory Access (DMA).

16. -------------- is the time needed by the CPU to recognize (not service) an interrupt request

 Interrupt Latency PG # 279

 Response Deadline
 Timer delay
 Throughput
17. In which one of the following methods, does the CPU poll to identify the interrupting module and branch to an
interrupt service routine on detecting an interrupt?

 Multiple interrupt lines

 Software Poll PG # 283
 Daisy Chain
 Parallel Priority

18. Which one of the following is a fixed size structure that stores the address of the first instruction of ISR?

 Interrupt vector PG # 277

 Interrupt request
 Interrupt handler
 Boot Sector

19. In Multiple Interrupt Lines approach, a number of interrupt lines are provided between the
____________________ modules.

 External and Internal

 CPU and I/O PG # 283
 CPU and Memory
 Memory and I/O

20. In FALCON-A assembler and simulator (FALSIM), variables are defined by using the _______ directive.

 .bin
 .equ
 .iret
 .end PG #9
21. _____________ allows a peripheral device to read from and/or write to memory without intervention by the
CPU.

 Programmed I/O
 Interrupt driven I/O
 Direct memory access PG # 316
 Polling

22. Taking control of the system bus for a few bus cycles is known as _____________.

 Bus Scheduling
 Cycle Stealing PG # 317
 Cycle Transferring
 CPU Scheduling

23. A Hard Disk sector has the _______________ parts.

 Header only
 Data section and a trailer
 Data section only
 Header, data section and a trailer PG # 323

24. Raid Level ____ is not a true member of the RAID family.

 0 PG # 330
 2
 3
 4

25. The conversion of numbers from a representation in one base to another is known as_______

 Radix Conversion PG # 333

 Number Representation
 Decimal Representation
 Hexadecimal Representation
26. A _______signal decides whether the input word should be shifted or bypassed.

 Control Read
 Shift/bypass PG # 346
 Control Write
 Control Transfer

27. In Single-Precision Binary Floating Point Representation the size of exponent is _______.

 8-bits PG # 348
 11-bits
 1-bits
 23-bits

28. In Double-Precision Binary Floating Point Representation the size of fraction is _______.

 23-bits
 52-bits PG # 348
 11-bits
 1-bits

29. For a request of data if the requested data is not present in the cache, it is called a _________

 Cache Miss PG # 358

 Spatial Locality
 Temporal Locality
 Cache Hit

30. For a request for data, if the data is available in the cache it results in a ____.

 Cache Miss
 Spatial Locality
 Temporal Locality
 Cache Hit PG # 358
31. For write to complete in Write through, the CPU has to wait. This wait state is called _______.

 Write Through
 Write Back
 Write Allocate
 Write Stall PG # 363

32. _____ contains permanent pattern of data that cannot be changed.

 RAM
 Hard Disk
 Cache
 ROM PG # 356

33. In Control Field of page table, _______ indicate the availability of page in main memory.

 Access Control Bits

 Used Bits
 Presence Bits PG # 367
 Redundant Bits

34. ______ are formed by concatenating the page number with the word number.

 Memory chips
 Protocols
 Hazards
 Virtual addresses PG # 366
35. In __________technique memory is divided into segments of variable sizes depending upon the requirements.

 Multiplexing
 Segmentation PG # 365
 Hamming code
 Partial decoding

36. _______ depends upon the average number of calls and the service time taken by a particular server.

 Through put PG # 380

 Latency
 Poisson Distribution
 Response Time

37. ________ is the maximum rate at which data can be transmitted through networks.

 Transmission Time
 Latency
 Transport Latency
 Bandwidth PG # 388

38. The time for the message to pass through the network, except the time of flight is called __________.

 Transmission Time PG # 388

 Latency
 Transport Latency
 Bandwidth

39. In physical media of networks, for increased and better performance we use _____ which are usually made of
glass.

 Coaxial Cables
 Twisted Pair Cables
 Fiber Optic Cable PG # 390
 Shielded Twisted Pair Cables
40. What does the instruction “ldr R3, 58” of SRC do?

 it will load the register R3 with the contents of the memory location M [PC+58]
 It will load the register R3 with the relative address itself (PC+58).
 It will store the register R3 contents to the memory location M [PC+58]
 No operation

41. What functionality is performed by the instruction “lar R3, 36” of SRC?

 It will load the register R3 with the contents of the memory location M [PC+36]

 It will load the register R3 with the relative address itself (PC+36). PG # 48

 It will store the register R3 contents to the memory location M [PC+36]

 No operation

42. What is the instruction length of the FALCON-E processor?

 8 bits
 16 bits
 32 bits PG # 124
 64 bits

43. Type A format of SRC uses -----------instructions

 two PG # 47
 three
 four
 five

44. Which instruction is used to store register to memory using relative address?

 ld instruction
 ldr instruction
 lar instruction
 str instruction PG # 48
 45. There are _________ types of reset operations in SRC

 Two PG # 195
 Three
 Four
 Five

46. Which one of the following is a bi-stable device, capable of storing one bit of Information?

 Decoder
 Flip-flop PG # 76
 Multiplexer
 Diplexer

47. Execution time of a program with respect to the processor is calculated as:

 Execution Time = IC x CPI x MIPS

 Execution Time = IC x CPI x T PG # 44
 Execution Time = CPI x T x MFLOPS
 Execution Time = IC x T

48. Which one of the following register stores a previously calculated value or a value loaded from the main
memory?

 Accumulator
 Address Mask
 Instruction Register
 Program Counter

Accumulator
Accumulator is located in CPU. Accumulator stores a previously calculated value or a value loaded from the main
memory. Without an accumulator it would be necessary to write the result of each calculation to main memory and
read them back. Access to main memory is slower than access to the accumulator which usually has direct paths to and
from the ALU.
49. Which one of the following is called 0-address machine?

 General purpose register machines

 RISC machines
 Accumulator based machines
 Stack based machines PG # 31

50. Which one of the following type of error occurs when a character is not available at the beginning of an
interval?

 Framing error
 Parity error
 Over-run error
 Under-run error PG # 240

51. Which one of the following type of error occurs when a 0 is received instead of a stop bit (which is always a 1)?

 Framing error PG # 240

 Parity error

 Over-run error

 Under-run error

52. An interface that is used to connect the computer bus with I/O devices is called _________.

 Buffer
 I/O port PG # 245
 Memory mapping
 Processor
 53. Consider Falcon A, with 16 address lines, the total address space is ________ Kbytes.

 2 ^ 16 PG # 256
 2 ^ 10
 2^6
 2^8

216 = 64 Kbytes.

54. ____________ is the process of periodically checking the status of a device to see if it is ready for the next I/O
operation.

 Polling PG # 270
 Snooping
 Data Bus Multiplexing
 Pipelining

55. Which one of the following is NOT a technique used when the CPU wants to exchange data with peripheral
device?

 Direct Memory Access

 Interrupt driven I/O
 Programmed I/O
 Virtual Memory PG # 268

There are three main techniques using which a CPU can exchange data with a peripheral
device, namely
• Programmed I/O
• Interrupt driven I/O
• Direct Memory Access (DMA).

56. Which one is the last instruction of the ISR that is to be executed when the ISR terminates?

 IRET PG # 278
 IRQ
 INT
 NMI
57. Which one of the following is a fixed size structure that stores the address of the first instruction of ISR?

 Interrupt request
 Interrupt handler
 Boot Sector
 Interrupt vector PG #277

58. Falcon-A Simulator loads a FALCON-A binary file with a ________ extension and presents its contents into
different areas of the simulator.

 .bin
 .binfa PG # 2
 .fa
 .asmfa

59. In Direct memory access (DMA), a ________ is needed to control the total activity and to synchronize the
transfer of data.

 DMA memory unit

 DMA controller PG 313
 Control software
 Programmed I/O

60. _____________ allows a peripheral device to read from and/or write to memory without intervention by the
CPU.

 Direct memory access PG # 316

 Polling
 Programmed I/O
 Interrupt driven I/O
61. A component connected to the system bus and having control of it during a particular bus cycle is called
_________.

 Address decoder
 BIOS
 Master component PG # 317
 Slave component

62. When it is required to read data from a particular location of the disk, the head moves towards the selected track
and this process is called_______.

 Seek PG # 322
 Encoding
 Fragmentation
 Defragmentation

63. CRC has __________overhead as compared to Hamming code.

 Equal
 Greater
 Lesser PG # 329
 Absolutely no

64. ______ is the simplest form for representing a signed number.

 Sign Magnitude Form PG # 330

 Radix Complement Form
 Biased Representation
 Diminished Radix Compliment Form

65. In _______ adder circuit we feed carry out from the previous stage to the next stage and so on.

 Ripple Carry Adder PG # 335

 Carry Look Ahead Adder
 Complement Adder
 2‟s Complement Adder
66. _______ are computed by the ALU and stored in processor status register.

 Condition Codes PG # 344

 Control Signals
 Flip Flops
 Multiplexers

67. In computers, floating-point representation uses ______to encode significant, exponent and their sign in a
single word.

 Decimal Numbers
 Binary Numbers PG # 341
 Octal Numbers
 Hexadecimal Numbers

68. In floating point representations ______ is also called mantissa.

 Sign
 Base
 Significant PG # 341
 Exponent

69. A _______signal decides whether the input word should be shifted or bypassed.

 Control Read
 Shift/bypass PG # 340
 Control Write
 Control Transfer

70. For a request of data if the requested data is not present in the cache, it is called a _________.

 Cache Miss PG # 349

 Spatial Locality
 Temporal Locality
 Cache Hit
71. Randomly replacing any older page to bring in the desired page is known as ______.

 Always Replacement
 LFU (Least Frequently Used)
 Random Replacement PG # 356
 Fragmentation

72. In Control Field of page table, _______ indicate the availability of page in main memory.

 Access Control Bits

 Used Bits
 Presence Bits PG # 356
 Redundant Bits

73. A set of rules followed by different components in a network is called ______.

 Host
 Connectivity
 Resource Sharing
 Protocol PG # 373

74. In ________ topology, all the computers are connected in the form of a circle.

 Bus
 Ring PG # 381
 Mesh
 Star

75. SPARC (Scalable Processor Architecture) is an example of _________architecture.

 CISC
 RISC PG # 148
 SRC
 FALCON
 76. Which one of the following is the memory organization of EAGLE processor?

 2^8 * 8 bits
 2^16 * 8 bits PG # 120
 2^32 * 8 bits
 2^64 * 8 bits

Memory organization is 2^16 x 8 bits. This means that there are 216 memory cells, each one byte
long

77. Which one of the following is the memory organization of SRC processor?

 2^8 * 8 bits
 2^16 * 8 bits
 2^32 * 8 bits PG # 46
 2^64 * 8 bits

78. _________ is a collection of binary digits or bits that the computer reads and interprets.

 Assembly language
 Higher level language
 English language
 Machine language Click Here For Reference Detail

79. In which one of the following addressing modes, the value to be stored in memory is obtained by directly
retrieving it from another memory location?

 Direct Addressing Mode Click Here For Reference Detail

 Immediate addressing mode
 Indirect Addressing Mode
 Register (Direct) Addressing Mode
80. The external interface of FALCON-A consists of a ______address bus and ______a data bus.

 8-bit, 8-bit
 16-bit, 16-bit Click Here For Reference Detail
 16-bit, 24-bit
 16-bit, 32-bit

81. In which of the following instructions the data move between a register in the processor and a memory location
(or another register) and are also called data movement?

 Arithmetic/logic

 Load/store PG # 141

 Test/branch

 None of the given

82. The __________ instruction is completed once memory access has been made and the memory location has
been written to.

 Store PG # 208
 Branch
 Load
 Control

83. Which type of instructions enables mathematical computations?

 Arithmetic PG # 92
 Control
 Data transfer
 Miscellaneous
84. ____________ Control signal allows the bus to read from the selected register.

 RBE
 RCE
 LCON
 R2BUS PG # 182

85. For any of the instructions that are a part of the instruction set of the SRC, there are certain _________
required; which may be used to select the appropriate function for the ALU to be performed, to select the
appropriate registers, or the appropriate memory location.

 Registers
 Control signals Page # 171
 Memory
 DMA controllers

86. Every I/O port has a unique identifier associated with it, which is called its _______.

 Address PG # 244
 Access point
 Interval Identifier
 Device Driver

87. Partial decoding is an attractive choice in ____________.

 Small system PG # 255

 Large system
 Medium system
 All of the above
88. Maskable Interrupts are applied to the ____________ pin of the processor.

 INTR PG # 275

 NMI

 IRET

 INT

89. Non-maskable Interrupts are detected using the ___________ pin of the processor.

 INTR

 NMI PG # 275

 IRET

 INT

90. In Multiple Interrupt Line, a number of interrupt lines are provided between the ____ modules.

 External and Internal

 CPU and the I/O Page # 283

 CPU and Memory

 Memory and I/O

91. In ____ recording, bits are encoded in pairs so there are only ' n/2' additions instead of 'n'.

 Booth Recording
 Bit-Pair Recording Page # 343
 Fraction Division
 Integer Division
92. ______ is nonvolatile i.e. it retains the information in it when power is removed from it.

 RAM

 DRAM

 ROM PG # 356

 SRAM

93. Based on the statistical results, the block which has been least used in the recent past, is replaced with a new
block. This technique is called _____.

 Always Replacement

 Random Replacement

 LFU (Least Frequently Used) Page # 362

 Write Allocate

94. ________ acts as a cache between main memory and secondary memory.

 Read Only Memory

 Flash Memory

 Virtual Memory PG # 364

 Magnetic Tape

95. ___________is also called traffic intensity and its value must be between 0 and 1.

 Little‟s Law

 Poisson Distribution

 Server Utilization PG # 381

 SPEC
96. What is the instruction length of SRC processor?

 8 bits

 16 bits

 32 bits PG # 134

 64 bits

97. What does the word „D‟ in the „D-flip-Flop‟ stands for?

 Data PG # 76

 Digital

 Dynamic

 Double

98. Almost every commercial computer has its own particular ---------- language

 assembly language PG # 25

 English language

 Higher level language

 3GL
99. Which field of the machine language instruction is the “type of operation” that is to be performed?

 Op-code (or the operation code) PG # 33

 CPU registers

 Memory cells

 I/O locations

100. ________ is/are defined as the time required to process a single instruction.

 Latency & throughput PG # 203

 Latency

 Throughput

 Hazards

101. In pipelining ____________ is increased by overlapping the instruction execution

 Latency

 Throughput PG # 220

 Execution time

 Clock speed

102. Which of the following register(s) takes input from the ALSU as the address of the memory location to

be accessed and transfers the memory contents on that location onto memory sub-system?

 Instruction Register

 Memory address register PG # 151

 Memory Buffer register

 Registers A and C
103. ____________ occurs when the exponent is too large and can not be represented in the exponent field.

 Underflow

 Overflow PG # 348

 Rounding off

 Normalize

104. The ________ is w-bit wide and contains a data word, directly connected to the data bus which is b-bit

wide memory address register (MAR).

 Instruction Register(IR)

 memory address register (MAR)

 memory Buffer Register(MBR) PG # 350

 Program counter (PC)

105. The______is m-bits wide and contains memory address generated by the CPU directly connected to the

m-bit wide address bus.

 memory address register (MAR) PG # 350

 Accumulator register

 Program counter register

 Instruction register

106. _____________ is a place for safe storage and provides the fastest possible storage after the registers.

 Hard Disk

 Cache PG # 356

 Compact Disk

 Floppy Disk
107. __________ refers to the interconnection of machines in a building or a campus.

 SAN

 LAN PG # 387

 WAN

 MAN

108. What is the size of the memory space that is available to SRC processor?

 2^8 bytes

 2^16 bytes

 2^32 bytes PG # 46

 2^64 bytes

109. Which operator is used to name registers, or part of registers, in the Register Transfer Language?

 := PG # 66

 &

 %

 ©

110. Which one of the following is the highest level of abstraction in digital design in which the computer
architect views the system for the description of system components and their interconnections?

 Processor-Memory-Switch level (PMS level) PG # 22

 Instruction Set Level

 Register Transfer Level

 None of the given

111. Which one of the following design levels is called the gate level?

 Logic Design Level PG # 22

 Circuit Level

 Mask Level

 None of the given

112. __________ Instructions usually involve calculating the target address and evaluating a condition.

 Add

 Branch PG # 209

 Load

 Store

113. Which of the instruction is used to load register from memory using a relative address?

 la

 nop

 ldr PG # 47

 str

114. We represent e^ instead of e to show _________.

 Sign Magnitude Form

 Radix Complement Form

 Diminished Radix Complement Form

 Biased Representation PG # 347

115. ______ is a combination of arithmetic, logic and shifter unit along with some multiplexers and control

unit.

 Computer Bus

 CPU Register

 Flip Flop

 ALU PG # 347

116. Connection Oriented Communication reserves the ________until the transfer is complete.

 Bandwidth PG # 394

 Error

 Checksum

 Protocol

117. In Connection-less Communication message is divided into _________.

 Tracks

 Sectors

 Platters

 Packets PG # 394
Note: If you found any mistake in mcqz please mail at above mentioned email address.
And tell me your answer with references.