Description

G152
ACS800 single drive, startup and basic
maintenance hands-on
Course type and description Course Goal
The ACS800 single drive learning event comprises of The goal of this course is to teach students to install,
two parts: e-learning courses and classroom course. start-up, operate, maintain and troubleshoot ACS800
This is the second part of the learning event: Course single drives.
G152 is a classroom course with hands-on exercises The training covers the following types and
and fault tracing with ACS800 demo units supported constructs:
by an instructor. n ACS800-01
The first part of the learning event includes the n ACS800-02 R7 or ACS800-04 R8
theory based e-learning courses mentioned below.
Please note that the e-learning course material is not n ACS800-11 on request
covered during the classroom course. You are
required to complete the e-learning part before the Course Objectives
classroom part, which is essential in order to be able Upon completion of this course, students will be able
to succeed in the hands-on lab activities during to:
classroom days. The status of e-learning course
completion is monitored. n Commission and tune ACS800 single drives
Please see the accompanying figure of possible n Operate and maintain ACS800 single drives
learning paths. n Do basic trouble shooting on ACS880 single
drives
Prerequisites
n Basic knowledge of electronics Main Topics
n Experience in using a Windows PC n ACS800 standard application program
n Course G152e. n Control panel functions
Please refer to the accompanying figure for course n Control panel assistants
names and durations. n Locating and identifying terminals
n Installation principles
Course Duration n Converter commissioning
The course duration is 2 days. n Fine tuning of the converter
n Adaptive programming
Student Profile
n DriveAP adaptive programming tool operations
This course is intended for electricians, technicians,
and engineers who install, operate and do basic n DriveWindow commissioning and maintenance
maintenance ACS800 single drives. tool operations
n Introduction to trouble shooting

Low voltage drives training

ABB University Finland, Helsinki Training Center
[email protected]
www.abb.com/abbuniversity
 Agenda

G152
ACS800 single drive, startup and basic
maintenance hands-on
Day 1 Day 2

09:00 Course Information 09:00 Exercises continues

09:15 Drive AP demo 10:00 Break (15min)

10:00 Break (15min) 10:15 Exercises continues

10:15 Exercises begin 12:00 Lunch (45min)

12:00 Lunch (45min) 12:45 Exercises continues

12:45 Exercises continues 14:00 Break (15min)

14:00 Break (15min) 14:15 Trouble shooting exercises

14:15 Exercises continues 15:45 Questions & Feedback

16:00 End of the day 16:00 End of the course

Low voltage drives training

ABB University Finland, Helsinki Training Center
[email protected]
www.abb.com/abbuniversity
 Learning Paths

ACS800 drives
Learning paths

Course code Duration

Course name
Would you
like to take G152e 1-2 days*
a course Yes
via the ? ACS800 Single Drive G158 2 days
Internet? Fundamentals
No Internet course
ACS800 Drives
DriveAP Programming
Do you
have G152A 1 days G152 2 days
knowledge
Yes ACS800-01,-02,-04,-11
of ACS600 G170 2 days
single ? Single Drive
drives? ACS800 Single Drive Start-Up & Service
No Fundamentals Hands-On Training
ACS800 Drives
Motion Control

G152B 2 days G156 1.5 days

ACS800-07,-17,-37 Single
G171 2 days
Drive
ACS800 Single Drive Start-Up & Service
Fundamentals Hands-On Training
ACS800 Drives
Intelligent Pump Control

G172 2.5 days

Would you ACS800 Drives

like to take Winder/Inline Control
a course G163e 1-2 days G163 1 day
via the
Internet? Yes
? ACS800 liquid-cooled ACS800 liquid-cooled G173 2 days
drives drives
No
Internet course Hands-On Training
ACS800 Drives
Template Control
G163A 1 day

G174 2 days
ACS800 liquid-cooled
drives ACS800 Drives
PCP/ESP & Rod Pump
Control

G175 2 days

ACS800 Drives
Crane Control Program
(+N697)
G160e 1-2 days* G160 1.5 days
Would you
like to take Yes G176 2 days
? ACS800 Multidrive ACS800 Multidrive
a course
via the Fundamentals Start-Up & Service Hands-
No ACS800 Drives
Internet? Internet Course On Training
Winch Control Program
(+N698)

G161 2.5 days

G162 2.5 days
ACS800 multidrive
ACS800 Multidrive
Control Section AC800M
Operation and
Maintenance Operation and
Maintenance

* The duration of the Internet courses depends on personal professional background and study pace