Scribd Logo
Upload

Welcome to Scribd!

  • 171 views

    A Full Wave Rectifier Is A Circuit Arrangement Which Makes Use of Both Half Cycles of Input Alternating Current

    Uploaded by

    Karan Soni
    A full wave rectifier converts both halves of the input AC cycle to DC, doubling the efficiency of a half wave rectifier. It can be constructed using a center-tapped transformer and two diodes or a bridge rectifier configuration with a normal transformer and four diodes. A bridge rectifier allows both diodes on each side of the bridge to conduct on alternate half-cycles, efficiently converting the entire AC input to DC output with low ripple.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    A Full Wave Rectifier Is A Circuit Arrangement Which Makes Use of Both Half Cycles of Input Alternating Current

    Uploaded by

    Karan Soni
    171 views9 pages
    A full wave rectifier converts both halves of the input AC cycle to DC, doubling the efficiency of a half wave rectifier. It can be constructed using a center-tapped transformer and two diodes or a bridge rectifier configuration with a normal transformer and four diodes. A bridge rectifier allows both diodes on each side of the bridge to conduct on alternate half-cycles, efficiently converting the entire AC input to DC output with low ripple.

    Original Description:

    Description of half cycles of full wave rectifier.

    Original Title

    A Full Wave Rectifier is a Circuit Arrangement Which Makes Use of Both Half Cycles of Input Alternating Current

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    A full wave rectifier converts both halves of the input AC cycle to DC, doubling the efficiency of a half wave rectifier. It can be constructed using a center-tapped transformer and two diodes or a bridge rectifier configuration with a normal transformer and four diodes. A bridge rectifier allows both diodes on each side of the bridge to conduct on alternate half-cycles, efficiently converting the entire AC input to DC output with low ripple.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    171 views9 pages

    A Full Wave Rectifier Is A Circuit Arrangement Which Makes Use of Both Half Cycles of Input Alternating Current

    Uploaded by

    Karan Soni
    A full wave rectifier converts both halves of the input AC cycle to DC, doubling the efficiency of a half wave rectifier. It can be constructed using a center-tapped transformer and two diodes or a bridge rectifier configuration with a normal transformer and four diodes. A bridge rectifier allows both diodes on each side of the bridge to conduct on alternate half-cycles, efficiently converting the entire AC input to DC output with low ripple.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 9

    A Full wave rectifier is a circuit arrangement which makes use of both half cycles of

    input alternating current (AC) and converts them to direct current (DC). In our tutorial
    on Half wave rectifiers, we have seen that a half wave rectifier makes use of only
    one-half cycle of the input alternating current. Thus a full wave rectifier is much more
    efficient (double+) than a half wave rectifier. This process of converting both half
    cycles of the input supply (alternating current) to direct current (DC) is termed full
    wave rectification.

    Full wave rectifier can be constructed in 2 ways. The first method makes use of a
    centre tapped transformer and 2 diodes. This arrangement is known as Center
    Tapped Full Wave Rectifier.

    The second method uses a normal transformer with 4 diodes arranged as a bridge.
    This arrangement is known as a Bridge Rectifier.

    Full Wave Rectifier Theory


    To understand full wave bridge rectifier theory perfectly, you need to learn half
    wave rectifier first. In the tutorial of half wave rectifier, we have clearly explained the
    basic working of a rectifier. In addition, we have also explained the theory behind a
    pn junction and the characteristics of a pn junction diode.

    Full Wave Rectifier – Working & Operation


    The working & operation of a full wave bridge rectifier is pretty simple. The circuit
    diagrams and waveforms we have given below will help you understand the
    operation of a bridge rectifier perfectly. In the circuit diagram, 4 diodes are arranged
    in the form of a bridge. The transformer secondary is connected to two diametrically
    opposite points of the bridge at points A & C. The load resistance RL is connected
    to bridge through points B and D.
    Full Wave Bridge Rectifier – Circuit Diagram with Input and Output Wave Forms

    During the first half cycle


    During the first half cycle of the input voltage, the upper end of the transformer
    secondary winding is positive with respect to the lower end. Thus during the first half
    cycle diodes D1 and D3 are forward biased and current flows through arm AB, enters
    the load resistance RL, and returns back flowing through arm DC. During this half of
    each input cycle, the diodes D2 and D4 are reverse biased and current is not allowed
    to flow in arms AD and BC. The flow of current is indicated by solid arrows in the
    figure above. We have developed another diagram below to help you understand the
    current flow quickly. See the diagram below – the green arrows indicate the
    beginning of current flow from the source (transformer secondary) to the load
    resistance. The red arrows indicate the return path of current from load resistance to
    the source, thus completing the circuit.

    Flow of current in Bridge Rectifier

    During the second half cycle


    During the second half cycle of the input voltage, the lower end of the transformer
    secondary winding is positive with respect to the upper end. Thus diodes D2 and
    D4 become forward biased and current flows through arm CB, enters the load
    resistance RL, and returns back to the source flowing through arm DA. The flow of
    current has been shown by dotted arrows in the figure. Thus the direction of flow of
    current through the load resistance RL remains the same during both half cycles of
    the input supply voltage. See the diagram below – the green arrows indicate the
    beginning of current flow from the source (transformer secondary) to the load
    resistance. The red arrows indicate the return path of current from load resistance to
    the source, thus completing the circuit.
    Path of current in 2nd Half Cycle

    Peak Inverse Voltage of a Full wave bridge


    rectifier:

    Let’s analyse peak inverse voltage (PIV) of a full wave bridge rectifier using the
    circuit diagram. At any instant when the transformer secondary voltage attains
    positive peak value Vmax, diodes D1 and D3 will be forward biased (conducting) and
    the diodes D2 and D4 will be reverse biased (non conducting). If we consider ideal
    diodes in bridge, the forward biased diodes D1 and D3 will have zero resistance.
    This means voltage drop across the conducting diodes will be zero. This will result in
    the entire transformer secondary voltage being developed across load resistance
    RL.

    Thus PIV of a bridge rectifier = Vmax (max of secondary voltage)

    Bridge Rectifier Circuit Analysis


    The only difference in the analysis between full wave and centre tap rectifier is that

    1. In a bridge rectifier circuit, two diodes conduct during each half cycle and the forward
    resistance becomes double (2RF).
    2. In a bridge rectifier circuit, Vsmax is the maximum voltage across the transformer
    secondary winding whereas in a centre tap rectifier Vsmax represents that maximum
    voltage across each half of the secondary winding.

    The different parameters are explained with equations below:

    1. Peak Current
    The instantaneous value of the voltage applied to the rectifier is given as
    vs = Vsmax Sin wt

    If the diode is assumed to have a forward resistance of RF ohms and a reverse


    resistance equal to infinity, the current flowing through the load resistance is given as

    i1 = Imax Sin wt and i2 = 0 for the first half cycle

    and i1 = 0 and i2 = Imax Sin wt for second half cycle

    The total current flowing through the load resistance RL, being the sum of currents i1
    and i2 is given as

    i = i1 + i2 = Imax Sin wt for the whole cycle.

    Where the peak value of the current flowing through the load resistance R L is given
    as

    Imax = Vsmax/(2RF + RL)

    2. Output Current

    Since the current is the same through the load resistance RL in the two halves of the
    ac cycle, magnitude od dc current Idc, which is equal to the average value of ac
    current, can be obtained by integrating the current i1 between 0 and pi or current i2
    between pi and 2pi.

    Output Current of Full Wave Rectifier

    3. DC Output Voltage

    Average or dc value of voltage across the load is given as

    DC Output Voltage of Full Wave Rectifier

    4. Root Mean Square (RMS) Value of Current

    RMS or effective value of current flowing through the load resistance RL is given as

    RMS Value of Current of Full Wave Rectifier


    5. Root Mean Square (RMS) Value of Output Voltage

    RMS value of voltage across the load is given as

    RMS Value of Output Voltage of Full Wave Rectifier

    6. Rectification Efficiency

    Power delivered to load,

    Rectification Efficiency of Full Wave Rectifier

    7. Ripple Factor

    Form factor of the rectified output voltage of a full wave rectifier is given as

    Ripple Factor of Full Wave Rectifier

    So, ripple factor, γ = 1.112 – 1) = 0.482

    8. Regulation

    The dc output voltage is given as


    Regulation of Full Wave Rectifier

    Merits and Demerits of Full-wave


    Rectifier Over Half-Wave Rectifier
    Merits – let us talk about the advantages of full wave bridge rectifier over half wave
    version first. I can think about 4 specific merits at this point.

     Efficiency is double for a full wave bridge rectifier. The reason is that, a half wave
    rectifier makes use of only one half of the input signal. A bridge rectifier makes use of
    both halves and hence double efficiency
     The residual ac ripples (before filtering) is very low in the output of a bridge rectifier.
    The same ripple percentage is very high in half wave rectifier. A simple filter is enough
    to get a constant dc voltage from the bridge rectifier.
     We know the efficiency of FW bridge is double than HW rectifier. This means higher
    output voltage, Higher transformer utilization factor (TUF) and higher output power.

    Demerits – Full-wave rectifier needs more circuit elements and is costlier.

    Merits and Demerits of Bridge Rectifier Over


    Center-Tap Rectifier.
    A centre tap rectifier is always a difficult one to implement because of the special
    transformer involved. A centre tapped transformer is costly as well. One key
    difference between center tap & bridge rectifier is in the number of diodes involved in
    construction. A center tap full wave rectifier needs only 2 diodes whereas a bridge
    rectifier needs 4 diodes. But silicon diodes being cheaper than a center tap
    transformer, a bridge rectifier is much-preferred solution in a DC power
    supply. Following are the advantages of bridge rectifier over a center tap rectifier.

     A bridge rectifier can be constructed with or without a transformer. If a transformer is


    involved, any ordinary step down/step up transformer will do the job. This luxury is not
    available in a center tap rectifier. Here the design of rectifier is dependent on the center
    tap transformer, which can not be replaced.
     Bridge rectifier is suited for high voltage applications. The reason is the high peak
    inverse voltage (PIV) of bridge rectifier when compared to the PIV of a center tap
    rectifier.
     Transformer utilization factor (TUF) is higher for bridge rectifier.

    Demerits of Bridge rectifier over center tap rectifier


    The significant disadvantage of a bridge rectifier over center tap is the involvement of
    4 diodes in the construction of bridge rectifier. In a bridge rectifier, 2 diodes conduct
    simultaneously on a half cycle of input. A center tap rectifier has only 1 diode
    conducting on one-half cycle. This increases the net voltage drop across diodes in a
    bridge rectifier (it is double to the value of center tap).

    Applications of Full wave Bridge rectifier


    Full wave rectifier finds uses in the construction of constant dc voltage power
    supplies, especially in general power supplies. A bridge rectifier with an efficient
    filter is ideal for any type of general power supply applications like charging a battery,
    powering a dc device (like a motor, led etc) etc. However, for an audio application, a
    general power supply may not be enough. This is because of the residual ripple
    factor in a bridge rectifier. There are limitations to filtering ripples. For audio
    applications, specially built power supplies (using IC regulators) may be ideal.

    Full Wave Bridge Rectifier with Capacitor Filter


    The output voltage of the full wave rectifier is not constant, it is always pulsating. But
    this cannot be used in real life applications. In other words, we desire a DC power
    supply with a constant output voltage. In order to achieve a smooth and constant
    voltage a filter with a capacitor or an inductor is used. The circuit diagram below
    shows a half wave rectifier with capacitor filter.
    Full Wave Rectifier – with Capacitor Filter

    Ripple factor in a bridge rectifier


    Ripple factor is a ratio of the residual ac component to dc component in the output
    voltage. Ripple factor in a bridge rectifier is half than that of a half wave rectifier.
    References
    1. To explain the concepts better, we have referred several textbooks,
    especially Principles of Electronics.
    2. To create the

    You might also like