IDLC-45: 45W Constant Current Mode LED Driver

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

45W Constant Current Mode LED Driver IDLC-45 series

F M M SELV
■ Features ■ Applications
Constant Current mode output LED panel lighting
Flicker free design LED flood lighting
Plastic housing with class II design Indoor LED lighting
Built-in active PFC function
No load power consumption<0.5W(Blank-Type)
Function options: 2 in 1 dimming (dim-to-off);
Auxiliary DC output
3 years warranty

■ Description
IDLC-45 series is a 45W LED AC/DC driver featuring the constant current mode output with flicker
free design.IDLC-45 operates from 90~295VAC and offers models with different rated current
ranging between 350mA and 1400mA. Thanks to the efficiency up to 86%, with the fanless design,
the entire series is able to operate for -20℃~+85℃ case temperature under free air convection.
IDLC-45 is equipped with various function options, such as dimming methodologies, so as to
provide the optimal design flexibility for lighting system.

■ Model Encoding
IDLC - 45 A - 500

Rated output current(350/500/700/1050/1400mA)

Function options

Rated wattage
Series name

Type Function Note


Blank 2 in 1 dimming (0~10VDC and 10V PWM) In Stock
A 2 in 1 dimming and Auxiliary DC output In Stock

File Name:IDLC-45-SPEC 2016-06-16


45W Constant Current Mode LED Driver IDLC-45 series
SPECIFICATION
MODEL IDLC-45 -350 IDLC-45 -500 IDLC-45 -700 IDLC-45 -1050 IDLC-45 -1400

RATED CURRENT 350mA 500mA 700mA 1050mA 1400mA


RATED POWER 33.25W 45W 44.8W 45.15W 44.8W
CONSTANT CURRENT REGION Note.2 57 ~ 95V 54 ~ 90V 38 ~ 64V 26 ~ 43V 19 ~ 32V

OUTPUT OPEN CIRCUIT VOLTAGE(max.) 118V 115V 84V 63V 50V

CURRENT RIPPLE 5% max. @rated current

CURRENT TOLERANCE ±7.0%


SETUP TIME Note.4 500ms / 230VAC 1200ms/115VAC
AUXILIARY DC OUTPUT Note.5 Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only
90 ~ 295VAC 127 ~ 417VDC
VOLTAGE RANGE Note.3
(Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE 47 ~ 63Hz

PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load


POWER FACTOR (Typ.) (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)

THD< 20%(@load≧60%/115VAC,230VAC; @load≧75%/277VAC)


INPUT TOTAL HARMONIC DISTORTION
(Please refer to “TOTAL HARMONIC DISTORTION” section)

EFFICIENCY (Typ.) 86% 85% 85% 84% 83%


AC CURRENT 0.6A/115VAC 0.4A/230VAC 0.3A/277VAC

INRUSH CURRENT (Typ.) COLD START 30A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410

MAX. No. of PSUs on 16A


CIRCUIT BREAKER 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC

LEAKAGE CURRENT <0.75mA / 277VAC

NO LOAD POWER CONSUMPTION <0.5W for Blank-Type, <1.2W for A-Type

PROTECTION SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed
WORKING TEMP. Tcase=-20 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)

MAX. CASE TEMP. Tcase=+85℃


WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH

TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 40℃)

VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes


SAFETY STANDARDS UL8750,CSA C22.2 NO.250.13-12;ENEC EN61347-1 & EN61347-2-13 independent, EN62384,GB19510.1,GB19510.14 approved

WITHSTAND VOLTAGE I/P-O/P:3.75KVAC


SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC
EMC EMISSION Compliance to EN55015, EN61000-3-2 Class C (@load≧60%) ; EN61000-3-3,GB17743,GB17625.1

EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( surge immunity:Line-Line:1KV )
MTBF 408.8Khrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 120*75*25mm(L*W*H)
PACKING 0.22Kg; 54pcs/ 13Kg/ 0.93CUFT

NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.
5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-)
are short circuit or when it is no load or short circuit at output(Vo+,Vo-).
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

File Name:IDLC-45-SPEC 2016-06-16


45W Constant Current Mode LED Driver IDLC-45 series

Block Diagram
fosc : 70KHz

AUX+(for A-Type)
RECTIFIERS
AUX-(for A-Type)

EMI FILTER POWER RECTIFIERS Vo+


I/P & SWITCHING &
RECTIFIERS Vo-
FILTER
CURRENT DIM+
LIMIT DIM-

O.L.P. DETECTION
PWM&PFC CIRCUIT
CONTROL

DRIVING METHODS OF LED MODULE

※ This series works in constant current mode to directly drive the LEDs.

In the constant current region, the highest voltage at the output of the driver
100 depends on the configuration of the end systems.

Constant Should there be any compatibility issues, please contact MEAN WELL.
Vo(%)

Current area

60
(min.)
Hiccup
Protection

50 100 Io(%)

Typical output current normalized by rated current (%)

File Name:IDLC-45-SPEC 2016-06-16


45W Constant Current Mode LED Driver IDLC-45 series

DIMMING OPERATION
※ 2 in 1 dimming function

ACL
ACL TB1
ACN
ACN

DIM+
DIM-
Vo+ TB2
Vo-

Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.

◎ Applying additive 0 ~ 10VDC 100%


90%
80%
+
Vo+ + 70%
Output current (%)

60%
-
Vo- - 50%
DIM+ 40%
+
30%
Additive Voltage
- 20%
DIM-
10%

“DO NOT connect "DIM- to Vo- ” 0%


0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage

◎ Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz): 100%
90%
80%
+
Vo+ + 70%
Output current (%)

60%
-
Vo- - 50%
DIM+ 40%

Additive PWM signal 30%


20%
DIM-
10%

“DO NOT connect "DIM- to Vo- ” 0%


0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Duty cycle of additive 10V PWM signal dimming input

Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< I out<8%.
2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.

File Name:IDLC-45-SPEC 2016-06-16


45W Constant Current Mode LED Driver IDLC-45 series

OUTPUT LOAD vs TEMPERATURE

90~295VAC for 350mA Model,200~295VAC for others 90~295VAC for 350mA Model,200~295VAC for others
100 100

80 80

90~200VAC for models other 90~200VAC for models other


60 than 350mA Model 60 than 350mA Model
LOAD (%)

LOAD (%)
40 40

20 20

-20 -10 0 10 20 30 40 (HORIZONTAL) -20 -10 0 15 30 45 60 85 (HORIZONTAL)

AMBIENT TEMPERATURE,Ta (℃) Tcase (℃)

STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC

※ Tcase at 75℃
100

90 for 350mA Model 1

80 0.95

70 for others 0.9


LOAD (%)

115V
PF

60
0.85
230V
50
0.8 277V
40
0.75
90 135 180 200 295
0.7

INPUT VOLTAGE (V) 50% 60% 70% 80% 90% 100%


(45W)

LOAD
※ De-rating is needed under low input voltage.

TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD


IDLC-45 series possess superior working efficiency that up to 86% can
be reached in field applications.
※ 350mA Model,Tcase at 75℃ ※ 350mA Model,Tcase at 75℃
16 90

14 88
12
86
EFFICIENCY(%)

10
THD(%)

277V 84 277V
8
230V 230V
6 82
115V 115V
4 80

2 78
0
76
50% 60% 70% 80% 90% 100%
50% 60% 70% 80% 90% 100%
LOAD
LOAD

File Name:IDLC-45-SPEC 2016-06-16


45W Constant Current Mode LED Driver IDLC-45 series

MECHANICAL SPECIFICATION
※ Blank-Type Case No.IDLC-45A Unit:mm

120
6.5
tc : Max. Case Temperature

1
2 TB1

6.5
3
4

1
75

2
3 TB2 30
4 tc
6.5

30
6.5
25
3

Terminal Pin No. Assignment(TB1)


Pin No. Assignment
1 ACL Terminal Pin No. Assignment(TB2)
2 ACL Pin No. Assignment
3 ACN 1 DIM+
4 ACN 2 DIM-
3 Vo+
4 Vo-

※ A-Type

120
6.5
tc : Max. Case Temperature

1
2
3 TB1
6.5

1
75

2
3 TB2 30
4 tc
5
6.5

6
30

6.5
25
3

Terminal Pin No. Assignment(TB1)


Pin No. Assignment
1 ACL
Terminal Pin No. Assignment(TB2)
2 ACL Pin No. Assignment Pin No. Assignment
3 ACN 1 DIM+ 4 Vo-
4 ACN 2 DIM- 5 AUX+
3 Vo+ 6 AUX-

Installation Manual
Please refer to : http://www.meanwell.com/webnet/search/InstallationSearch.html

File Name:IDLC-45-SPEC 2016-06-16

You might also like