Mat Foundation Design Page 1 of 26

DESIGN OF MAT FOUNDATION

Mat Foundation Design(ACI 318-11) - Metric

Job Details

Job Name : MAT FOUNDATION

Included
X (m) Y (m) Z (m)
Support
1 0.00 0.00 0.00
3 5.40 0.00 0.00
5 11.20 0.00 0.00
7 0.00 0.00 8.60
9 5.40 0.00 8.60
11 11.20 0.00 8.60
13 0.00 0.00 15.45
15 5.40 0.00 15.45
17 11.20 0.00 15.45
19 0.00 0.00 22.30
21 5.40 0.00 22.30
23 11.20 0.00 22.30
25 0.00 0.00 29.90
27 8.67 0.00 29.90
255 8.67 0.00 15.45
257 8.67 0.00 22.30

Load Details

Included Loads

Load Case No 301: 1.0(DL1 + DL2) + 1.0(LL1 + LL2 + LLR)

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -11.65 -2458.40 -34.46 -18.61 7.19

3 -1.80 -3512.37 -18.88 -10.05 1.12
5 14.59 -2491.67 -47.75 -25.30 -8.97
7 -5.88 -3165.10 10.31 5.39 3.76
9 -1.15 -4934.95 5.67 3.11 0.85

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 2 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

11 4.27 -3580.26 15.32 8.50 -2.49

13 -3.50 -2948.68 -0.09 -0.18 2.40
15 5.40 -3494.56 1.27 0.75 -3.08
17 250.57 -3175.54 -434.09 18.38 9.35
19 -3.86 -3078.19 -7.50 -4.15 2.72
21 3.87 -3674.44 3.75 2.08 -2.04
23 313.09 -3782.48 475.75 0.35 10.35
25 -31.39 -2897.37 33.98 18.08 19.78
27 32.57 -2701.43 38.30 20.72 -19.60
255 -253.94 -2623.45 -2.35 -0.94 -10.59
257 -311.19 -3220.74 -39.23 -18.31 -10.03

Load Case No 302: 1.0(DL1 + DL2) + 0.75(LL1 + LL2 + LLR) + 0.535EX

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 54.61 -1995.53 -27.56 -19.23 -90.70

3 97.71 -3420.92 -16.52 -11.57 -117.23
5 80.02 -2756.67 -49.18 -27.21 -106.34
7 62.61 -2709.22 15.10 3.64 -94.54
9 99.23 -4697.27 9.11 2.17 -117.08
11 69.99 -3827.87 8.92 3.93 -99.08
13 65.71 -2477.33 4.18 -2.21 -95.59
15 124.86 -2595.89 3.93 -0.61 -132.00
17 356.23 -6951.64 -959.58 26.79 -57.98
19 66.71 -2612.57 -3.56 -6.37 -95.34
21 122.18 -2761.73 6.90 0.98 -129.49
23 440.90 -7410.54 978.15 -14.80 -54.93
25 33.55 -2612.81 41.08 17.56 -73.97
27 100.90 -2774.42 32.96 16.01 -115.43
255 20.83 303.37 -0.25 -2.78 -148.92
257 -31.33 -526.71 -43.68 -23.02 -149.21

Load Case No 303: 1.0(DL1 + DL2) + 0.75(LL1 + LL2 + LLR) - 0.535EX

Load Type : Service

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 3 of 26

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -77.93 -2769.07 -42.68 -18.43 104.89

3 -101.23 -3313.73 -22.83 -9.27 119.23
5 -50.04 -2070.48 -46.50 -23.55 87.72
7 -73.68 -3457.79 6.34 7.85 101.35
9 -101.35 -4684.23 3.27 4.72 118.38
11 -60.27 -3062.58 21.93 13.13 93.10
13 -72.63 -3227.15 -3.97 2.32 99.97
15 -113.55 -4054.87 -1.56 2.13 125.16
17 128.05 730.80 112.13 9.47 76.22
19 -74.45 -3339.66 -11.17 -1.54 100.35
21 -113.59 -4220.72 2.18 4.13 124.45
23 160.93 67.73 -50.13 15.08 74.56
25 -98.30 -3001.35 27.60 19.25 114.22
27 -32.68 -2430.10 43.85 25.57 73.82
255 -515.51 -5354.49 -3.98 1.14 128.14
257 -568.48 -5640.09 -34.49 -13.45 129.12

Load Case No 304: 1.0(DL1 + DL2) + 0.75(LL1 + LL2 + LLR) + 0.535EZ

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -35.89 -2520.36 15.46 113.29 52.97

3 -47.62 -3218.08 24.88 91.73 60.19
5 -8.59 -2095.22 -9.69 44.62 36.16
7 -15.22 -3150.70 97.12 157.06 23.69
9 -21.34 -4614.82 76.64 119.47 27.46
11 -4.27 -3261.86 71.99 88.40 16.95

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 4 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

13 -2.38 -2868.29 89.96 153.22 2.60

15 7.61 -3228.62 73.29 117.68 -3.56
17 158.41 -1147.06 -198.56 87.04 -1.48
19 7.73 -2915.47 80.90 148.37 -16.81
21 26.81 -3538.33 55.03 107.89 -28.56
23 399.77 -6616.53 808.23 56.03 9.37
25 -11.25 -2883.90 88.42 152.40 -19.76
27 55.18 -2755.89 84.99 107.84 -60.65
255 -87.08 -1637.84 28.93 103.93 -11.62
257 -421.88 -3374.78 13.55 96.88 -36.31

Load Case No 305: 1.0(DL1 + DL2) + 0.75(LL1 + LL2 + LLR) - 0.535EZ

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 12.57 -2244.25 -85.69 -150.94 -38.78

3 44.10 -3516.57 -64.23 -112.57 -58.19
5 38.56 -2731.93 -85.99 -95.38 -54.78
7 4.15 -3016.31 -75.68 -145.58 -16.88
9 19.22 -4766.68 -64.26 -112.59 -26.16
11 13.99 -3628.59 -41.14 -71.34 -22.94
13 -4.54 -2836.19 -89.75 -153.12 1.78
15 3.69 -3422.13 -70.91 -116.16 -3.29
17 325.87 -5073.78 -648.89 -50.78 19.71
19 -15.47 -3036.75 -95.64 -156.28 21.82
21 -18.22 -3444.13 -45.95 -102.77 23.52
23 202.06 -726.28 119.80 -55.75 10.27
25 -53.49 -2730.26 -19.73 -115.59 60.00
27 13.04 -2448.62 -8.18 -66.26 19.04
255 -407.60 -3413.27 -33.16 -105.57 -9.16
257 -177.93 -2792.01 -91.71 -133.36 16.22

Load Case No 306: 0.6(DL1 + DL2) + 0.7EX

Load Type : Service

Serviceability Factor : 1.00

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 5 of 26

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 79.70 -786.35 -12.36 -12.22 -123.86

3 129.16 -1829.43 -9.10 -8.42 -154.31
5 94.79 -1756.49 -30.61 -17.76 -133.15
7 86.47 -1213.51 12.90 1.32 -126.75
9 130.75 -2383.43 8.46 0.99 -154.01
11 89.18 -2324.74 0.93 -0.85 -128.43
13 88.51 -1047.22 5.74 -2.52 -127.00
15 159.83 -736.23 4.15 -1.32 -170.90
17 279.38 -6774.94 -936.70 21.75 -82.75
19 90.02 -1126.25 0.79 -5.17 -126.91
21 157.58 -810.47 7.23 0.33 -168.51
23 341.80 -6895.24 929.98 -19.84 -79.79
25 65.07 -1267.54 30.07 10.52 -110.43
27 110.62 -1608.12 16.12 6.33 -138.47
255 214.35 2362.28 1.59 -2.85 -187.13
257 191.78 1742.37 -29.20 -17.07 -188.15

Load Case No 307: 0.6(DL1 + DL2) - 0.7EX

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -93.71 -1798.46 -32.14 -11.17 132.04

3 -131.14 -1689.18 -17.35 -5.41 155.08
5 -75.38 -858.66 -27.11 -12.97 120.76
7 -91.86 -2192.94 1.44 6.83 129.55
9 -131.69 -2366.36 0.83 4.33 154.07
11 -81.25 -1323.42 17.96 11.18 123.02
13 -92.51 -2028.30 -4.93 3.42 128.87
15 -152.12 -2645.18 -3.02 2.27 165.57

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 6 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

17 -19.17 3276.85 465.54 -0.91 92.84

19 -94.68 -2077.58 -9.16 1.15 129.14
21 -150.91 -2719.43 1.06 4.45 163.75
23 -24.52 2889.40 -415.43 19.25 89.64
25 -107.44 -1775.91 12.43 12.73 135.80
27 -64.16 -1157.60 30.37 18.85 109.16
255 -487.40 -5040.52 -3.30 2.29 175.38
257 -511.04 -4948.03 -17.18 -4.55 176.02

Load Case No 308: 0.6(DL1 + DL2) + 0.7EZ

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -38.70 -1473.04 43.92 161.17 64.11

3 -60.99 -1564.03 45.07 126.74 77.83
5 -21.14 -891.03 21.06 76.22 53.30
7 -15.37 -1791.15 120.22 202.07 27.94
9 -27.00 -2275.55 96.82 154.47 35.10
11 -7.98 -1584.17 83.46 109.67 23.39
13 -0.58 -1558.76 117.97 200.86 1.47
15 6.42 -1564.11 94.90 153.45 -2.84
17 20.55 819.84 59.03 100.59 -8.82
19 12.84 -1522.58 111.31 197.29 -24.16
21 32.80 -1826.58 70.20 140.21 -36.45
23 287.98 -5856.35 707.65 72.83 4.34
25 6.44 -1622.24 92.00 186.94 -39.49
27 50.79 -1583.87 84.20 126.48 -66.80
255 73.16 -177.62 39.77 136.77 -7.49
257 -319.22 -1984.08 45.67 139.82 -40.43

Load Case No 309: 0.6(DL1 + DL2) - 0.7EZ

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 7 of 26

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 24.69 -1111.78 -88.42 -184.56 -55.93

3 59.01 -1954.57 -71.52 -140.57 -77.06
5 40.55 -1724.11 -78.78 -106.95 -65.69
7 9.98 -1615.30 -105.88 -193.91 -25.14
9 26.06 -2474.25 -87.52 -149.15 -35.05
11 15.91 -2064.00 -64.57 -99.34 -28.80
13 -3.41 -1516.76 -117.16 -199.96 0.41
15 1.29 -1817.30 -93.77 -152.50 -2.49
17 239.66 -4317.93 -530.18 -79.74 18.91
19 -17.51 -1681.26 -119.68 -201.31 26.39
21 -26.13 -1703.32 -61.92 -135.42 31.69
23 29.30 1850.52 -193.10 -73.42 5.51
25 -48.81 -1421.21 -49.50 -163.69 64.86
27 -4.34 -1181.84 -37.71 -101.30 37.48
255 -346.22 -2500.62 -41.48 -137.34 -4.26
257 -0.04 -1221.58 -92.05 -161.43 28.30

Load Case No 310: 1.0(DL1 + DL2) + 1.0(LL1 + LL2 + LLR) + 0.71EX

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 76.29 -1945.12 -24.43 -19.14 -122.59

3 130.21 -3583.50 -14.70 -11.58 -155.79
5 100.89 -2947.00 -49.53 -27.73 -137.74
7 84.56 -2668.39 16.12 2.60 -126.22
9 131.94 -4943.60 9.54 1.42 -155.39
11 90.71 -4088.07 6.69 2.40 -130.01
13 88.30 -2451.13 5.32 -3.19 -127.37
15 163.60 -2526.45 4.91 -1.07 -173.72
17 401.98 -8273.23 -1145.23 29.87 -79.69

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 8 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

19 89.81 -2595.74 -2.45 -7.36 -127.13

21 160.32 -2706.33 6.88 -0.01 -170.54
23 498.86 -8744.69 1158.07 -19.47 -75.57
25 56.10 -2639.55 42.92 16.96 -105.09
27 121.21 -2929.90 31.07 14.38 -145.18
255 101.95 1130.83 0.13 -3.54 -194.44
257 45.24 172.25 -45.33 -24.66 -194.71

Load Case No 311: 1.0(DL1 + DL2) + 1.0(LL1 + LL2 + LLR) - 0.71EX

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -99.60 -2971.68 -44.50 -18.08 136.97

3 -133.80 -3441.25 -23.07 -8.52 158.02
5 -71.70 -2036.34 -45.97 -22.88 119.79
7 -96.31 -3661.81 4.49 8.18 133.74
9 -134.25 -4926.29 1.80 4.81 157.09
11 -82.16 -3072.44 23.96 14.61 125.03
13 -95.30 -3446.22 -5.50 2.83 132.16
15 -152.80 -4462.67 -2.37 2.57 167.56
17 99.17 1922.16 277.04 6.89 98.40
19 -97.53 -3560.65 -12.55 -0.95 132.57
21 -152.57 -4642.56 0.62 4.17 166.46
23 127.31 1179.74 -206.57 20.18 96.28
25 -118.88 -3155.18 25.04 19.20 144.66
27 -56.07 -2472.95 45.52 27.07 105.99
255 -609.82 -6377.74 -4.82 1.67 173.26
257 -667.62 -6613.73 -33.13 -11.96 174.66

Load Case No 312: 1.0(DL1 + DL2) + 1.0(LL1 + LL2 + LLR) + 0.71EX

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 9 of 26

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 76.29 -1945.12 -24.43 -19.14 -122.59

3 130.21 -3583.50 -14.70 -11.58 -155.79
5 100.89 -2947.00 -49.53 -27.73 -137.74
7 84.56 -2668.39 16.12 2.60 -126.22
9 131.94 -4943.60 9.54 1.42 -155.39
11 90.71 -4088.07 6.69 2.40 -130.01
13 88.30 -2451.13 5.32 -3.19 -127.37
15 163.60 -2526.45 4.91 -1.07 -173.72
17 401.98 -8273.23 -1145.23 29.87 -79.69
19 89.81 -2595.74 -2.45 -7.36 -127.13
21 160.32 -2706.33 6.88 -0.01 -170.54
23 498.86 -8744.69 1158.07 -19.47 -75.57
25 56.10 -2639.55 42.92 16.96 -105.09
27 121.21 -2929.90 31.07 14.38 -145.18
255 101.95 1130.83 0.13 -3.54 -194.44
257 45.24 172.25 -45.33 -24.66 -194.71

Load Case No 313: 1.0(DL1 + DL2) + 1.0(LL1 + LL2 + LLR) - 0.71EX

Load Type : Service

Serviceability Factor : 1.00

Design Factor : 0.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -99.60 -2971.68 -44.50 -18.08 136.97

3 -133.80 -3441.25 -23.07 -8.52 158.02
5 -71.70 -2036.34 -45.97 -22.88 119.79
7 -96.31 -3661.81 4.49 8.18 133.74
9 -134.25 -4926.29 1.80 4.81 157.09
11 -82.16 -3072.44 23.96 14.61 125.03
13 -95.30 -3446.22 -5.50 2.83 132.16
15 -152.80 -4462.67 -2.37 2.57 167.56
17 99.17 1922.16 277.04 6.89 98.40
19 -97.53 -3560.65 -12.55 -0.95 132.57
21 -152.57 -4642.56 0.62 4.17 166.46

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 10 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

23 127.31 1179.74 -206.57 20.18 96.28

25 -118.88 -3155.18 25.04 19.20 144.66
27 -56.07 -2472.95 45.52 27.07 105.99
255 -609.82 -6377.74 -4.82 1.67 173.26
257 -667.62 -6613.73 -33.13 -11.96 174.66

Load Case No 401: 1.4(DL1 + DL2)

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -16.35 -3015.62 -51.91 -27.28 9.55

3 -2.31 -4105.04 -30.86 -16.14 0.90
5 22.64 -3051.00 -67.34 -35.86 -14.46
7 -6.29 -3974.20 16.73 9.51 3.26
9 -1.10 -5541.43 10.84 6.21 0.07
11 9.26 -4256.19 22.03 12.05 -6.31
13 -4.66 -3588.10 0.95 1.05 2.19
15 8.99 -3944.98 1.31 1.10 -6.22
17 303.58 -4081.10 -549.68 24.32 11.77
19 -5.44 -3737.81 -9.76 -4.69 2.59
21 7.78 -4118.21 9.67 5.58 -5.55
23 370.16 -4673.48 600.31 -0.69 11.49
25 -49.43 -3550.69 49.58 27.12 29.59
27 54.20 -3226.66 54.24 29.38 -34.20
255 -318.57 -3124.61 -1.99 -0.66 -13.71
257 -372.47 -3739.93 -54.11 -25.22 -14.15

Load Case No 402: 1.2(DL1 + DL2) + 1.6(LL1 + LL2) + 0.5LLR

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 11 of 26

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -13.88 -3044.57 -40.26 -21.90 8.70

3 -2.18 -4398.11 -21.33 -11.41 1.49
5 16.82 -3088.62 -57.13 -30.23 -10.21
7 -7.45 -3881.61 11.75 5.98 4.95
9 -1.47 -6228.65 5.97 3.23 1.27
11 4.10 -4466.81 18.17 10.14 -2.16
13 -4.16 -3650.40 -0.39 -0.53 3.10
15 6.03 -4408.16 1.60 0.88 -3.18
17 311.21 -3885.36 -534.00 22.30 11.49
19 -4.50 -3813.11 -9.19 -5.25 3.48
21 3.96 -4645.02 3.25 1.76 -1.73
23 392.15 -4688.87 586.07 0.86 13.18
25 -36.05 -3585.48 40.20 21.22 23.09
27 36.68 -3367.25 45.79 24.77 -21.68
255 -312.51 -3271.73 -3.20 -1.31 -12.96
257 -388.74 -4050.38 -47.30 -22.08 -11.95

Load Case No 403: 1.2(DL1 + DL2) + 1.6LLR + 0.5LL1 + 1.0LL2

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -14.24 -2866.53 -42.31 -22.67 8.69

3 -2.03 -4039.16 -23.85 -12.61 1.17
5 18.08 -2869.31 -58.00 -30.74 -11.21
7 -7.28 -3651.11 12.96 6.96 4.50
9 -1.02 -5597.05 7.54 4.22 0.65
11 5.92 -4087.36 18.59 10.31 -3.63
13 -4.94 -3328.82 0.26 0.15 3.14
15 6.87 -3944.63 1.39 0.92 -4.13
17 289.39 -3696.58 -506.71 21.47 10.71
19 -5.46 -3472.46 -8.97 -4.80 3.54
21 5.15 -4146.71 5.49 3.12 -2.99
23 363.98 -4415.40 555.67 0.52 11.72
25 -39.78 -3301.70 41.55 22.28 24.75

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 12 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

27 41.39 -3130.47 46.05 24.95 -25.22

255 -294.36 -3016.58 -2.72 -1.03 -12.28
257 -361.68 -3725.82 -46.94 -21.87 -11.76

Load Case No 404: 1.2(DL1 + DL2) + 0.5LL1 + 0.5LLR + 1.0LL2 + 1.0EX

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 109.71 -2116.39 -28.13 -23.35 -174.17

3 183.92 -4090.55 -17.89 -14.71 -219.86
5 139.56 -3484.29 -60.47 -34.15 -192.55
7 120.25 -2904.48 21.18 3.08 -178.71
9 186.49 -5525.26 12.99 1.84 -219.48
11 127.57 -4757.06 6.39 1.68 -183.21
13 124.47 -2585.74 7.90 -4.04 -179.74
15 229.65 -2525.13 6.47 -1.66 -244.49
17 499.68 -10846.70 -1504.61 37.50 -114.82
19 126.59 -2748.86 -1.85 -9.26 -179.48
21 225.49 -2725.33 9.91 0.19 -240.37
23 622.39 -11373.68 1512.85 -27.29 -109.41
25 83.51 -2902.70 54.13 20.75 -151.23
27 166.28 -3418.69 35.88 16.02 -202.19
255 209.66 2304.04 0.75 -4.70 -271.15
257 143.30 1089.31 -55.52 -30.80 -271.82

Load Case No 405: 1.2(DL1 + DL2) + 0.5LL1 + 0.5LLR + 1.0LL2 - 1.0EX

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 13 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -138.01 -3562.26 -56.39 -21.85 191.40

3 -187.93 -3890.20 -29.68 -10.41 222.13
5 -103.53 -2201.68 -55.46 -27.31 170.17
7 -134.49 -4303.67 4.81 10.96 187.44
9 -188.42 -5500.88 2.09 6.62 220.65
11 -115.91 -3326.59 30.71 18.87 176.00
13 -134.12 -3987.28 -7.34 4.44 185.79
15 -215.98 -5252.20 -3.78 3.47 236.19
17 73.19 3513.01 498.59 5.12 136.02
19 -137.27 -4107.90 -16.06 -0.23 186.30
21 -215.21 -5452.42 1.09 6.09 234.29
23 99.07 2604.38 -409.18 28.55 132.63
25 -162.95 -3628.94 28.95 23.89 200.53
27 -83.41 -2775.09 56.23 33.90 151.56
255 -792.84 -8271.40 -6.22 2.64 246.72
257 -860.72 -8468.40 -38.35 -12.91 248.42

Load Case No 406: 1.2(DL1 + DL2) + 0.5LL1 + 0.5LLR + 1.0LL2 + 1.0EZ

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -59.43 -3097.24 52.27 224.36 94.35

3 -87.71 -3711.35 59.50 178.39 111.76
5 -26.05 -2247.89 13.34 100.11 73.80
7 -25.22 -3729.61 174.50 289.88 42.28
9 -38.87 -5371.11 139.21 221.12 50.68
11 -11.23 -3699.07 124.28 159.57 33.67
13 -2.80 -3316.50 168.23 286.52 3.78
15 10.50 -3707.75 136.11 219.45 -4.41
17 129.91 2.46 -82.56 150.11 -9.20
19 16.35 -3315.07 156.04 279.98 -32.71
21 47.23 -4177.69 99.87 200.03 -51.72
23 545.95 -9895.43 1195.68 105.06 10.78
25 -0.24 -3409.52 142.61 272.78 -49.90
27 80.82 -3384.97 133.13 187.67 -99.80
255 7.96 -1324.08 55.28 194.77 -14.52

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 14 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

257 -587.16 -4238.23 51.43 193.33 -60.80

Load Case No 407: 1.2(DL1 + DL2) + 0.5LL1 + 0.5LLR + 1.0LL2 - 1.0EZ

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 31.13 -2581.15 -136.80 -269.54 -77.13

3 83.71 -4269.26 -107.07 -203.49 -109.50
5 62.08 -3438.01 -129.29 -161.57 -96.18
7 10.99 -3478.40 -148.50 -275.81 -33.55
9 36.94 -5654.96 -124.13 -212.63 -49.53
11 22.90 -4384.54 -87.19 -139.00 -40.89
13 -6.84 -3256.50 -167.66 -286.09 2.26
15 3.18 -4069.46 -133.43 -217.62 -3.91
17 442.92 -7337.22 -924.29 -107.50 30.40
19 -27.01 -3541.77 -173.94 -289.45 39.51
21 -36.96 -4001.60 -88.87 -193.73 45.63
23 176.40 1114.38 -91.11 -103.86 12.46
25 -79.18 -3122.34 -59.54 -228.13 99.18
27 2.07 -2810.63 -41.02 -137.73 49.16
255 -591.14 -4642.65 -60.78 -196.82 -9.92
257 -131.18 -3148.95 -145.31 -237.03 37.38

Load Case No 408: 0.9(DL1 + DL2) + 1.0EX

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 15 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 113.35 -1215.68 -19.24 -18.29 -176.65

3 184.44 -2739.13 -13.94 -12.53 -220.41
5 136.10 -2602.66 -45.79 -26.47 -190.65
7 123.33 -1855.25 18.94 2.18 -180.98
9 186.75 -3574.54 12.42 1.60 -220.02
11 127.69 -3451.36 2.00 -0.85 -183.66
13 126.30 -1605.87 8.23 -3.56 -181.36
15 228.60 -1172.52 5.97 -1.86 -244.34
17 408.41 -9803.42 -1354.96 31.82 -117.85
19 128.43 -1723.36 0.83 -7.53 -181.23
21 225.35 -1283.88 10.62 0.64 -240.89
23 499.62 -9993.41 1346.93 -28.37 -113.63
25 91.45 -1919.47 44.47 15.86 -156.86
27 159.69 -2396.08 24.69 9.95 -198.87
255 296.46 3279.04 2.21 -4.09 -267.75
257 262.57 2374.62 -43.37 -25.16 -269.22

Load Case No 409: 0.9(DL1 + DL2) - 1.0EX

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -134.37 -2661.54 -47.50 -16.79 188.93

3 -187.41 -2538.78 -25.73 -8.22 221.58
5 -106.99 -1320.05 -40.79 -19.63 172.07
7 -131.42 -3254.44 2.57 10.05 185.17
9 -188.16 -3550.16 1.52 6.38 220.11
11 -115.79 -2020.89 26.33 16.34 175.55
13 -132.29 -3007.41 -7.01 4.92 184.17
15 -217.04 -3899.59 -4.28 3.27 236.34
17 -18.09 4556.29 648.23 -0.55 132.99
19 -135.42 -3082.40 -13.39 1.50 184.56
21 -215.34 -4010.96 1.80 6.54 233.76
23 -23.70 3984.65 -575.10 27.47 128.41
25 -155.00 -2645.71 19.28 19.01 194.91
27 -90.00 -1752.48 45.04 27.83 154.89
255 -706.04 -7296.40 -4.77 3.25 250.13

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 16 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

257 -741.46 -7183.10 -26.20 -7.27 251.03

Load Case No 410: 0.9(DL1 + DL2) + 1.0EZ

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 -55.79 -2196.65 61.16 229.41 91.88

3 -87.20 -2360.00 63.45 180.56 111.21
5 -29.51 -1366.30 28.02 107.79 75.70
7 -22.15 -2680.45 172.25 288.96 40.01
9 -38.61 -3420.42 138.64 220.87 50.15
11 -11.12 -2393.39 119.90 157.03 33.22
13 -0.97 -2336.64 168.55 286.98 2.17
15 9.44 -2355.20 135.61 219.24 -4.25
17 38.65 1046.27 67.50 144.44 -12.23
19 18.18 -2289.53 158.71 281.70 -34.44
21 47.09 -2735.46 100.58 200.47 -52.24
23 422.73 -8509.28 1029.30 104.01 6.55
25 7.69 -2426.18 132.95 267.89 -55.51
27 74.22 -2361.45 121.94 181.59 -96.47
255 94.76 -349.40 56.75 195.37 -11.11
257 -467.43 -2948.88 63.59 198.97 -58.18

Load Case No 411: 0.9(DL1 + DL2) - 1.0EZ

Load Type : Ultimate

Serviceability Factor : 0.00

Design Factor : 1.00

Self Weight Factor : 1.00

Column Reactions Applied as Loads on the Mat

For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical
axis.

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 17 of 26

Fy
(kN)
Fx Fz Mx Mz
NODE NO. Downwards is
(kN) (kN) (kNm) (kNm)
negative Upwards is
positive

1 34.77 -1680.57 -127.91 -264.49 -79.60

3 84.23 -2917.91 -103.12 -201.31 -110.05
5 58.62 -2556.42 -114.60 -153.89 -94.29
7 14.06 -2429.24 -150.74 -276.73 -35.82
9 37.20 -3704.27 -124.70 -212.88 -50.06
11 23.02 -3078.86 -91.57 -141.54 -41.33
13 -5.02 -2276.63 -167.34 -285.62 0.65
15 2.12 -2716.91 -133.92 -217.82 -3.75
17 351.67 -6293.40 -774.23 -113.17 27.37
19 -25.18 -2516.22 -171.27 -287.73 37.78
21 -37.09 -2559.38 -88.15 -193.29 45.11
23 53.19 2500.53 -257.48 -104.91 8.23
25 -71.25 -2139.00 -69.20 -233.02 93.56
27 -4.54 -1787.11 -52.21 -143.81 52.50
255 -504.35 -3667.96 -59.31 -196.21 -6.51
257 -11.45 -1859.60 -133.16 -231.39 39.99

Properties Details

Region Thickness(m) Material

mat 1.10 Concrete

Soil Details

Boundary Subgrade Modulus Soil Height Above Mat Soil Density Applied Load due to Soil
mat 18000.00kN/m2/m 1.20m 18.00kN/m3 21.60kN/m^2

Mat Dimension

Boundary Name : mat

Node No X Coor(m) Y Coor(m) Z Coor(m)
1 -1.50 0.00 -1.50
2 12.72 0.00 -1.50
3 12.72 0.00 31.40
4 -1.50 0.00 31.40

Analysis Results

Node Displacement Summary Table

Rx Ry Rz
- Node Number Load Case Dx(mm) Dy(mm) Dz(mm)
(Rad) (Rad) (Rad)

Max Dx 1 301 0.00 -11.12 0.00 -0.00 0.00 0.00

Max Dy 65 409 0.00 0.11 0.00 -0.00 0.00 0.00
Max Dz 1 301 0.00 -11.12 0.00 -0.00 0.00 0.00
Max Rx 60 406 0.00 -15.45 0.00 0.00 0.00 -0.00

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 18 of 26

Rx Ry Rz
- Node Number Load Case Dx(mm) Dy(mm) Dz(mm)
(Rad) (Rad) (Rad)

Max Ry 1 301 0.00 -11.12 0.00 -0.00 0.00 0.00

Max Rz 752 409 0.00 -4.89 0.00 0.00 0.00 0.00
Min Dx 1 301 0.00 -11.12 0.00 -0.00 0.00 0.00
Min Dy 55 404 0.00 -23.68 0.00 0.00 0.00 -0.00
Min Dz 1 301 0.00 -11.12 0.00 -0.00 0.00 0.00
Min Rx 69 404 0.00 -19.15 0.00 -0.00 0.00 -0.00
Min Ry 1 301 0.00 -11.12 0.00 -0.00 0.00 0.00
Min Rz 751 404 0.00 -19.03 0.00 0.00 0.00 -0.00

Plate Stress Summary Table

SQx SQy Sx Sy Sxy Mx My Mxy
- Plate Load Case
(kN/m2 ) (kN/m2) (kN/m2) (kN/m2) (kN/m2) (kN-m/m) (kN-m/m) (kN-m/m)

Max SQX 877 404 2730.91 -298.73 0.00 0.00 0.00 1663.81 1010.02 -11.65
Max SQY 899 404 -1949.57 2349.39 0.00 0.00 0.00 2534.62 940.73 -440.30
Max SX 1 301 24.79 37.74 0.00 0.00 0.00 26.08 29.64 -18.85
Max SY 1 301 24.79 37.74 0.00 0.00 0.00 26.08 29.64 -18.85
Max SXY 1 301 24.79 37.74 0.00 0.00 0.00 26.08 29.64 -18.85
Max MX 900 406 -2862.44 -168.92 0.00 0.00 0.00 3220.14 1190.91 -31.74
Max MY 882 405 1516.29 -1754.16 0.00 0.00 0.00 1436.10 1742.19 20.59
Max MXY 580 404 411.09 -650.08 0.00 0.00 0.00 301.35 -380.59 667.62
Min SQX 900 404 -3248.17 -356.08 0.00 0.00 0.00 2745.29 1215.21 -417.40
Min SQY 901 404 -1433.35 -2499.89 0.00 0.00 0.00 2002.95 389.98 -333.99
Min SX 1 301 24.79 37.74 0.00 0.00 0.00 26.08 29.64 -18.85
Min SY 1 301 24.79 37.74 0.00 0.00 0.00 26.08 29.64 -18.85
Min SXY 1 301 24.79 37.74 0.00 0.00 0.00 26.08 29.64 -18.85
Min MX 900 411 712.42 188.29 0.00 0.00 0.00 -1040.63 -373.19 -157.26
Min MY 629 408 -425.43 631.51 0.00 0.00 0.00 -285.62 -1433.68 189.10
Min MXY 948 404 -508.10 -588.77 0.00 0.00 0.00 469.06 -254.19 -728.13

Base Pressure Summary for Service Load conditions

Base Pressure
- Node X-Coor(m) Y-Coor(m) Z-Coor(m) Load Case
(kN/m2)
Maximum Base
55 12.72 0.00 16.17 310 347.71
Pressure
Minimum Base
65 12.72 0.00 22.26 307 8.65
Pressure

Contact Area
Load Case Area in Contact(m2) % of Total Area Area out of Contact(m2) % of Total Area
301 467.84 100.00 0.00 0.00
302 467.84 100.00 0.00 0.00
303 467.84 100.00 0.00 0.00
304 467.84 100.00 0.00 0.00
305 467.84 100.00 0.00 0.00
306 467.84 100.00 0.00 0.00
307 467.84 100.00 0.00 0.00

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 19 of 26

308 467.84 100.00 0.00 0.00

309 467.84 100.00 0.00 0.00
310 467.84 100.00 0.00 0.00
311 467.84 100.00 0.00 0.00
312 467.84 100.00 0.00 0.00
313 467.84 100.00 0.00 0.00
401 467.84 100.00 0.00 0.00
402 467.84 100.00 0.00 0.00
403 467.84 100.00 0.00 0.00
404 467.84 100.00 0.00 0.00
405 467.84 100.00 0.00 0.00
406 467.84 100.00 0.00 0.00
407 467.84 100.00 0.00 0.00
408 467.84 100.00 0.00 0.00
409 467.08 99.84 0.75 0.16
410 467.84 100.00 0.00 0.00
411 467.84 100.00 0.00 0.00

Sliding Check
Sliding Force, Fx Sliding Force, Fz Resisting Force FOS(x) FOS(z)
Load Case No
(kN) (kN) (kN) (Along X Direction) (Along Z Direction)
301 0.00 0.00 29678.03 N/A 51524041.15
302 1764.71 -0.00 28913.28 16.38 N/A
303 -1764.71 -0.00 28913.28 16.38 N/A
304 0.00 1401.12 28913.28 N/A 20.64
305 -0.00 -1401.12 28913.28 N/A 20.64
306 2308.97 0.00 19564.30 8.47 15836417.90
307 -2308.97 -0.00 19564.30 8.47 40836812.58
308 0.00 1833.24 19564.30 N/A 10.67
309 -0.00 -1833.24 19564.30 N/A 10.67
310 2341.95 0.00 29678.03 12.67 18840297.67
311 -2341.95 -0.00 29678.03 12.67 N/A
312 2341.95 0.00 29678.03 12.67 18840297.67
313 -2341.95 -0.00 29678.03 12.67 N/A

Overturning Check
Distance to Distance to
Critical Critical Overturning Overturning Resisting Resisting FOS(x) FOS(z)
Load Case
Location Location Moment, Mx Moment, Mz Moment, Rx Moment, Rz (About X (About Z
No
Along X Along Z (kNm) (kNm) (kNm) (kNm) Direction) Direction)
(m) (m)
301 -1.50 -1.50 -0.17 0.73 1177151.00 -527097.48 6977818.49 723174.74
302 12.72 -1.50 -36.74 -3442.54 1146169.63 445581.36 31199.97 129.43
303 -1.50 31.40 38.56 3435.36 -1164818.11 -472692.46 30211.56 137.60
304 -1.50 31.40 3146.94 50.63 -1132966.28 -513019.73 360.02 10133.49
305 12.72 -1.50 -3145.12 -57.81 1114317.78 485908.63 354.30 8405.72
306 12.72 -1.50 -46.77 -4509.49 766216.03 273377.85 16382.75 60.62
307 -1.50 31.40 51.74 4489.63 -775855.41 -287704.51 14994.52 64.08
308 -1.50 31.40 4118.78 61.01 -734180.14 -340469.17 178.25 5580.69
309 12.72 -1.50 -4113.81 -80.87 724540.76 326142.50 176.12 4033.10
310 12.72 -1.50 -50.13 -4563.11 1177200.97 445462.12 23483.64 97.62
311 -1.50 31.40 49.79 4564.57 -1196710.40 -473651.00 24034.60 103.77
312 12.72 -1.50 -50.13 -4563.11 1177200.97 445462.12 23483.64 97.62
313 -1.50 31.40 49.79 4564.57 -1196710.40 -473651.00 24034.60 103.77

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 20 of 26

Mat Self Weight = 11227.72 kN

Centre of Gravity of Mat (From Origin) = {5.61, 0.00, 14.95} m

Punching Shear Check

Column No. Load Case Service Stress (kN/m) Corner 1 (kN/m) Corner 2 (kN/m) Corner 3 (kN/m) Corner 4 (kN/m) Design Status
1 405 1473.72 -592.05 -639.11 -633.88 -586.82 Pass
3 407 1473.72 -772.45 -745.52 -696.80 -723.72 Pass
5 404 1473.72 -627.31 -579.97 -571.79 -619.13 Pass
7 405 1473.72 -716.18 -762.28 -764.90 -718.81 Pass
9 402 1473.72 -1071.24 -1071.55 -1072.32 -1072.01 Pass
11 404 1473.72 -840.88 -795.83 -796.23 -841.28 Pass
13 405 1473.72 -662.73 -708.41 -709.47 -663.79 Pass
15 405 1473.72 -874.30 -932.38 -933.21 -875.14 Pass
17 404 1473.72 -1876.04 -1847.81 -1856.79 -1885.02 Fail
19 405 1473.72 -683.98 -729.79 -729.73 -683.92 Pass
21 405 1473.72 -908.68 -966.29 -967.74 -910.13 Pass
23 404 1473.72 -1973.82 -1946.91 -1940.38 -1967.28 Fail
25 405 1473.72 -596.93 -646.23 -651.96 -602.65 Pass
27 406 1473.72 -572.26 -547.72 -592.66 -617.20 Pass
255 405 1473.72 -1392.63 -1453.30 -1453.93 -1393.26 Pass
257 405 1473.72 -1428.18 -1489.27 -1486.17 -1425.09 Fail

Design Parameters

Min Max
Top Bottom Pedestal Pedestal Min Max Wood and
Panel f 'c Pedestal Bar Bar
fy (kN/m2) Cover Cover Min Bar Max Bar Spacing Spacing Armer
Name (kN/m2) Cover(m) Size Size
(m) (m) Size (mm) Size (mm) (mm) (mm) Moment
(mm) (mm)
mat 415000.07 35000.01 0.07 0.07 0.04 20 32 12 60 50.00 200.00 Used

Design Output

Top of Mat Longitudinal Direction

Zone = 2

Governing Moment (MGOV) = 972.20 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.92 (m)

Steel Percentage Required

= 0.0018

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 21 of 26

= 13.95
Where

= 393.27 (kN/m^2)

Provided Area of Steel = 2.78 (in2)

As , Hence is acceptable

Reinforcement Details

Bar No = 25

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 150 (mm)

Smin<= S <= Smax

---------------------------------------

Zone = 3

Governing Moment (MGOV) = 1900.37 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.92 (m)

Steel Percentage Required

= 0.0018

Where = 13.95

= 768.72 (kN/m^2)

Provided Area of Steel = 2.78 (in2)

As , Hence is acceptable

Reinforcement Details

Bar No = 25

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 22 of 26

Actual Spacing (S) = 70 (mm)

Smin<= S <= Smax

---------------------------------------

Top of Mat Transverse Direction

Zone = 2

Governing Moment (MGOV) = 769.55 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.90 (m)

Steel Percentage Required

= 0.0018

Where = 13.95

= 325.36 (kN/m^2)

As , Hence is acceptable

Reinforcement Details

Bar No = 20

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 120 (mm)

Smin<= S <= Smax

---------------------------------------

Zone = 3

Governing Moment (MGOV) = 1510.69 (kN-m/m)

Otherwise, = 0.80

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 23 of 26

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.90 (m)

Steel Percentage Required

= 0.0018

Where = 13.95

= 638.71 (kN/m^2)

As , Hence is acceptable

Reinforcement Details

Bar No = 32

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 160 (mm)

Smin<= S <= Smax

---------------------------------------

Bottom of Mat Longitudinal Direction

Zone = 2

Governing Moment (MGOV) = -1280.19 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.92 (m)

Steel Percentage Required

= 0.0018

Where = 13.95

= 517.85 (kN/m^2)

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 24 of 26

As , Hence is acceptable

Reinforcement Details

Bar No = 20

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 70 (mm)

Smin<= S <= Smax

---------------------------------------

Zone = 3

Governing Moment (MGOV) = -2485.02 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.92 (m)

Steel Percentage Required

= 0.0023

Where = 13.95

= 1005.22 (kN/m^2)

As , Hence is acceptable

Reinforcement Details

Bar No = 32

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 90 (mm)

Smin<= S <= Smax

---------------------------------------

Bottom of Mat Transverse Direction

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 25 of 26

Zone = 2

Governing Moment (MGOV) = -2157.45 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.90 (m)

Steel Percentage Required

= 0.0020

Where = 13.95

= 912.15 (kN/m^2)

As , Hence is acceptable

Reinforcement Details

Bar No = 25

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 60 (mm)

Smin<= S <= Smax

---------------------------------------

Zone = 3

Governing Moment (MGOV) = -4101.19 (kN-m/m)

Otherwise, = 0.80

Minimum % of Steel Required

= 0.0018

= 0.03

Effective Depth (d) = 0.90 (m)

= 0.0039

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019
Mat Foundation Design Page 26 of 26

Steel Percentage Required

Where = 13.95

= 1733.95 (kN/m^2)

As , Hence is acceptable

Reinforcement Details

Bar No = 32

Maximum Spacing(Smax)(User Specified) = 200.00 (mm)

Minimum Spacing(Smin)(User Specified) = 50.00 (mm)

Actual Spacing (S) = 40 (mm)

Smin<= S <= Smax

---------------------------------------

Print Calculation Sheet

file:///C:/Users/Jake/Desktop/mat1/MAT%20FOUNDATION/Reports/CalculationSheet.xml 7/31/2019