Structural Analysis and Design Report

Ground and other Four Floors

Project:, Khartoum- Bahry- Kafouri

Plot No: 561 Block No: 3
Owner: Mr. Omar Aladdin Sheikh Idris
Anas Mohammed Hassan Ahmed.
Omar Mahgoub Khaled
Moath Mohammed Hassan Ahmed
Sayed Ahmed Abbas Sayed Ahmed
Musab Mohammed Hassan Ahmed
Miqdad Abdul Karim Hassan
Analysis and Design by: Dr. Taha Elnoor Ishaag
Eng. Sharief Ajban,
Eng. Rammah Ahmed.

Sep 2019
Preview:

Pursuant to the request from the representative of the above mentioned Project to
form a committee to conduct a structural analysis and design review to their concrete
building and to carry a comprehensive structural check to the design drawings, and to
check whether the building with Ground and other four Floors can withstand the total
loads and transfer them to the foundation safety or not, and to recommend any
corrective or preventive actions if required.
Scope of Work:

The purpose of the study is to investigate the presence of ultimate confidence in

the safety and adequacy of the structural elements capacity of the building and the
maximum ultimate design loads the building can carry, and to check the capability
of the structure to safety transfer the loads to the foundation with safe and
adequate columns.
Submittals:

1. Architectural drawings: Design drawings.

2. Structural drawings: Design drawings.
Methodology:

The building was modeled according to the submitted drawings, all dimensions were
checked for consistency, and reinforcement stated in the design drawings and actually
used was entered in the model. Material property was collected and defined to the
model elements and members according to what has been stated in the drawings.
British Standards Spread sheets and ETABS &SAFE software were used for analysis
and design. British standard and Euro codes were adopted.
Specifications, standards and programs

1. BS 8110-97 used for design and verifications of the results.

2. BS 6399 Part 1 1996 for loading.
3. ETABS 2015 & SAFE 2016 software.
Method of Analysis and Loading

Structural behavior of the system was captured through a complete three dimensional
model of structural analysis by using British Standards Spread sheets. Matrix stiffness
and finite elements methods are the tools that the program uses during the analysis.
The design loads used to analyze the building are adopted in accordance with the
BS6399 considering material properties and building utilization. Load combinations
for design assessment purposes were chosen according to BS 8110-97. Ultimate load
combination was used.
Loads Considered:

The building was checked according to following types of loads:

1. Dead load of 2.0 kN/m2 as finishes (Sand bedding, Ceramic and 4.5 cm mortar).
2. Self weight of the structure.
3. Walls as 4.5 kN/m2 and 13.5 kN/m for line wall of 25cm thickness brick walls with
wall density 18.0 kN/m3.
4. Live load of 1.5 kN/m2 is used for residential building.
5. Live load of 3.0kN/m2 on staircase.
6. Concrete density 24kN/m3 and gravitational acceleration 9.81m/s2.
7. Soil Bearing pressure 170 kN/m2 was used.
Materials and Load Combinations:

Concrete:
Columns + Slabs + Walls & Foundation : C 20/25MPA
Steel for Reinforcement:
The steel used is: St 460 MPA and 250MPA for stirrups.
Ultimate Limit State: For BS 8110-97 Code here:
DL: Dead Load. (Includes self weight, finishes and walls)
LL: Live Load.
Table of Contents

1. Structure Data 4

1.1 Story Data 4

2. Properties 5

2.1 Materials 5
2.2 Frame Sections 5
2.3 Shell Sections 5

3. Loads 6

3.1 Load Patterns 6

3.2 Auto Wind Loading 6
3.3 Applied Loads 15
3.3.1 Line Loads 15
3.3.2 Area Loads 17

4. Analysis Results 18

4.1 Structure Results 18

5. Design Data 19

5.1 Concrete Frame Design 19

List of Tables
Table 1.1 Story Data 4
Table 2.1 Material Properties - Summary 5
Table 2.2 Frame Sections - Summary 5
Table 2.3 Shell Sections - Summary 5
Table 3.1 Load Patterns 6
Table 3.3 Frame Loads - Distributed 15
Table 3.4 Shell Loads - Uniform 17
Table 4.1 Base Reactions 18
Table 5.1 Concrete Frame Preferences - BS 8110-97 19
Table 5.2 Concrete Column Overwrites - BS 8110-97 19
Table 5.3 Concrete Beam Overwrites - BS 8110-97 26
Table 5.4 Concrete Column PMM Envelope 30
Table 5.5 Concrete Column Shear Envelope 38
Table 5.6 Concrete Beam Flexure Envelope 52
Table 5.7 Concrete Beam Shear Envelope 65
Table 5.8 Concrete Joint Envelope 91
1 Structure Data
This chapter provides model geometry information, including items such as story levels, point coordinates, and
element connectivity.

1.1 Story Data

Table 1.1 - Story Data

Height Elevation Master Splice
Name Similar To
mm mm Story Story
Story7 3200 22200 No None No
Story6 3200 19000 Yes None No
Story5 3200 15800 No Story6 No
Story4 3200 12600 No Story6 No
Story3 3200 9400 No Story6 No
Story2 3200 6200 No Story6 No
Story1 3000 3000 No None No
Base 0 0 No None No

2 Properties
This chapter provides property information for materials, frame sections, shell sections, and links.

2.1 Materials

Table 2.1 - Material Properties - Summary

Unit
E
Name Type ν Weight Design Strengths
MPa
kN/m³
Fy=1689.91 MPa,
A416Gr270 Tendon 196500.6 0 76.9729
Fu=1861.58 MPa
conc25 Concrete 24855.58 0.2 24 Fc=25 MPa
Fy=250 MPa, Fu=312
fy250 Rebar 199947.98 0 76.9729
MPa
Fy=460 MPa, Fu=575
fy460 Rebar 199947.98 0.3 76.9729
MPa

2.2 Frame Sections

Table 2.2 - Frame Sections - Summary

Name Material Shape
Concrete
B 0.5*0.25 conc25
Rectangular
Concrete
B 0.7*0.25 conc25
Rectangular
C1 2ND&3RD Concrete
conc25
700*250 12T16 Rectangular
C1 4TH&ROOF Concrete
conc25
600*250 10T16 Rectangular
C1 GR&1ST Concrete
conc25
800*250 16T16 Rectangular
C1 Sh 800*300 Concrete
conc25
16T16 Rectangular
C2 2ND&3rd Concrete
conc25
700*250 12T16 Rectangular
C2 4TH&ROOF Concrete
conc25
600*250 12T16 Rectangular
C2 GR&1st Concrete
conc25
700*250 16T16 Rectangular
C2 Sh 700*300 Concrete
conc25
16T16 Rectangular
C3 2ND&3RD Concrete
conc25
600*250 8T16 Rectangular
 Name Material Shape
C3 4TH&ROOF Concrete
conc25
600*250 8T16 Rectangular
C3 GR&1ST Concrete
conc25
600*250 12T16 Rectangular
C3 Sh 600*300 Concrete
conc25
12T16 Rectangular

2.3 Shell Sections

Table 2.3 - Shell Sections - Summary

Total
Design Element
Name Material Thickness
Type Type
mm
FLAT Slab
Slab Shell-Thin conc25 230
230
Wall 200 Wall Shell-Thin conc25 200

3 Loads
This chapter provides loading information as applied to the model.

3.1 Load Patterns

Table 3.1 - Load Patterns

Self
Name Type Weight Auto Load
Multiplier
Dead Dead 1
Reducible
Live 0
Live
Wind Wind 0 ASCE 7-10

3.2 Auto Wind Loading

ASCE 7-10 Auto Wind Load Calculation
This calculation presents the automatically generated lateral wind loads for load pattern Wind according to ASCE 7-
10, as calculated by ETABS.

Exposure Parameters

Exposure From = Diaphragms

Exposure Category = B
Wind Direction = 0 degrees
Basic Wind Speed, V [ASCE 26.5.1]
Windward Coefficient, Cp,wind [ASCE 27.4.1]
Leeward Coefficient, Cp,lee [ASCE 27.4.1]

Wind Case = All Cases

Top Story = Story7
Bottom Story = Story1
Include Parapet = No

Factors and Coefficients

Gradient Height, zg [ASCE Table 26.9-1]

Emperical Exponent, α [ASCE Table 26.9-1]
Velocity Pressure Exposure Coefficient, Kz; [ASCE Table 27.3-1]

Topographical Factor, Kzt [ASCE 26.8.2]

Directionality Factor, Kd [ASCE 26.6]
Gust Effect Factor, G [ASCE 26.9]

Lateral Loading

Velocity Pressure, qz [ASCE 27.3.2 Eq. 27.3-1]

Design Wind Pressure, p [ASCE 27.4.2 Eq. 27.4-2]

Applied Story Forces

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
Story7 22.2 0 0 Story7 22.2 0 0
Story6 19 82.8724 0 Story6 19 0 72.6506
Story5 15.8 79.7685 0 Story5 15.8 0 69.8771
Story4 12.6 76.0347 0 Story4 12.6 0 66.5406
Story3 9.4 71.3186 0 Story3 9.4 0 62.3265
Story2 6.2 68.0699 0 Story2 6.2 0 59.4236
Story1 3 31.5106 0 Story1 3 0 27.0767
Base 0 0 0 Base 0 0 0
Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
Story7 22.2 0 0 Story7 22.2 0 0
Story6 19 62.1543 0 Story6 19 62.1543 0
Story5 15.8 59.8264 0 Story5 15.8 59.8264 0
Story4 12.6 57.026 0 Story4 12.6 57.026 0
Story3 9.4 53.489 0 Story3 9.4 53.489 0
Story2 6.2 51.0524 0 Story2 6.2 51.0524 0
Story1 3 23.633 0 Story1 3 23.633 0
Base 0 0 0 Base 0 0 0
Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
Story7 22.2 0 0 Story7 22.2 0 0
Story6 19 0 54.4879 Story6 19 0 54.4879
Story5 15.8 0 52.4078 Story5 15.8 0 52.4078
Story4 12.6 0 49.9055 Story4 12.6 0 49.9055
Story3 9.4 0 46.7449 Story3 9.4 0 46.7449
Story2 6.2 0 44.5677 Story2 6.2 0 44.5677
Story1 3 0 20.3075 Story1 3 0 20.3075
Base 0 0 0 Base 0 0 0
Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
Story7 22.2 0 0 Story7 22.2 0 0
Story6 19 62.1543 -55.5389 Story6 19 60.9781 54.4879
Story5 15.8 59.8264 -53.4588 Story5 15.8 58.6502 52.4078
Story4 12.6 57.026 -50.9565 Story4 12.6 55.8498 49.9055
Story3 9.4 53.489 -47.7959 Story3 9.4 52.3128 46.7449
Story2 6.2 51.0524 -45.6187 Story2 6.2 49.8762 44.5677
Story1 3 23.633 -20.7879 Story1 3 23.0869 20.3075
Base 0 0 0 Base 0 0 0
Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
Story7 22.2 0 0 Story7 22.2 0 0
Story6 19 46.6572 -41.6912 Story6 19 46.6572 -41.6912
Story5 15.8 44.9097 -40.1297 Story5 15.8 44.9097 -40.1297
Story4 12.6 42.8075 -38.2513 Story4 12.6 42.8075 -38.2513
Story3 9.4 40.1524 -35.8788 Story3 9.4 40.1524 -35.8788
Story2 6.2 38.3234 -34.2444 Story2 6.2 38.3234 -34.2444
Story1 3 17.7405 -15.6048 Story1 3 17.7405 -15.6048
Base 0 0 0 Base 0 0 0
Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
Story7 22.2 0 0 Story7 22.2 0 0
Story6 19 45.7743 40.9023 Story6 19 45.7743 40.9023
Story5 15.8 44.0268 39.3408 Story5 15.8 44.0268 39.3408
Story4 12.6 41.9246 37.4624 Story4 12.6 41.9246 37.4624
Story3 9.4 39.2695 35.0898 Story3 9.4 39.2695 35.0898
Story2 6.2 37.4404 33.4555 Story2 6.2 37.4404 33.4555
Story1 3 17.3305 15.2442 Story1 3 17.3305 15.2442
Base 0 0 0 Base 0 0 0
3.3 Applied Loads

3.3.1 Line Loads

Table 3.3 - Frame Loads - Distributed

Absolute Absolute
Relative Relative Force at Force at
Unique Design Load LoadTyp Directio Distance Distance
Story Label Distance Distance Start End
Name Type Pattern e n Start End
Start End kN/m kN/m
mm mm
Story7 B15 190 Beam Dead Force Gravity 0 1 0 2650 12.15 12.15
Story7 B16 196 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story7 B17 193 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story6 B1 210 Beam Dead Force Gravity 0 1 0 1625 11.25 11.25
Story6 B2 228 Beam Dead Force Gravity 0 1 0 2899.9 11.25 11.25
Story6 B3 277 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story6 B5 242 Beam Dead Force Gravity 0 1 0 2062.9 11.25 11.25
Story6 B6 9 Beam Dead Force Gravity 0 1 0 2901.6 11.25 11.25
Story6 B7 16 Beam Dead Force Gravity 0 1 0 4168 11.25 11.25
Story6 B16 192 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story6 B17 191 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story6 B20 288 Beam Dead Force Gravity 0 1 0 4300 12.15 12.15
Story6 B21 289 Beam Dead Force Gravity 0 1 0 5450 12.15 12.15
Story6 B22 290 Beam Dead Force Gravity 0 1 0 4249.1 12.15 12.15
Story6 B27 234 Beam Dead Force Gravity 0 1 0 5981.1 12.15 12.15
Story6 B14 235 Beam Dead Force Gravity 0 1 0 2483 11.25 11.25
Story6 B29 270 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story6 B25 263 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story6 B10 256 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story6 B26 249 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story6 B32 287 Beam Dead Force Gravity 0 1 0 4150 12.15 12.15
Story6 B8 220 Beam Dead Force Gravity 0 1 0 1118.7 12.15 12.15
Story5 B1 212 Beam Dead Force Gravity 0 1 0 1625 11.25 11.25
Story5 B2 229 Beam Dead Force Gravity 0 1 0 2899.9 11.25 11.25
Story5 B3 275 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story5 B5 243 Beam Dead Force Gravity 0 1 0 2062.9 11.25 11.25
Story5 B6 11 Beam Dead Force Gravity 0 1 0 2901.6 11.25 11.25
Story5 B7 18 Beam Dead Force Gravity 0 1 0 4168 11.25 11.25
Story5 B16 195 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story5 B17 194 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story5 B20 292 Beam Dead Force Gravity 0 1 0 4300 12.15 12.15
Story5 B21 293 Beam Dead Force Gravity 0 1 0 5450 12.15 12.15
Story5 B22 294 Beam Dead Force Gravity 0 1 0 4249.1 12.15 12.15
Story5 B27 239 Beam Dead Force Gravity 0 1 0 5981.1 12.15 12.15
Story5 B14 236 Beam Dead Force Gravity 0 1 0 2483 11.25 11.25
Story5 B29 268 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story5 B25 261 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story5 B10 254 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story5 B26 247 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story5 B32 291 Beam Dead Force Gravity 0 1 0 4150 12.15 12.15
Story5 B8 221 Beam Dead Force Gravity 0 1 0 1118.7 12.15 12.15
Story4 B1 219 Beam Dead Force Gravity 0 1 0 1625 11.25 11.25
Story4 B2 230 Beam Dead Force Gravity 0 1 0 2899.9 11.25 11.25
Story4 B3 278 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story4 B5 244 Beam Dead Force Gravity 0 1 0 2062.9 11.25 11.25
Story4 B6 12 Beam Dead Force Gravity 0 1 0 2901.6 11.25 11.25
Story4 B7 19 Beam Dead Force Gravity 0 1 0 4168 11.25 11.25
Story4 B16 198 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story4 B17 197 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story4 B20 296 Beam Dead Force Gravity 0 1 0 4300 12.15 12.15
Story4 B21 297 Beam Dead Force Gravity 0 1 0 5450 12.15 12.15
 Absolute Absolute
Relative Relative Force at Force at
Unique Design Load LoadTyp Directio Distance Distance
Story Label Distance Distance Start End
Name Type Pattern e n Start End
Start End kN/m kN/m
mm mm
Story4 B22 298 Beam Dead Force Gravity 0 1 0 4249.1 12.15 12.15
Story4 B27 241 Beam Dead Force Gravity 0 1 0 5981.1 12.15 12.15
Story4 B14 237 Beam Dead Force Gravity 0 1 0 2483 11.25 11.25
Story4 B29 271 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story4 B25 264 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story4 B10 257 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story4 B26 250 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story4 B32 295 Beam Dead Force Gravity 0 1 0 4150 12.15 12.15
Story4 B8 222 Beam Dead Force Gravity 0 1 0 1118.7 12.15 12.15
Story3 B1 224 Beam Dead Force Gravity 0 1 0 1625 11.25 11.25
Story3 B2 231 Beam Dead Force Gravity 0 1 0 2899.9 11.25 11.25
Story3 B3 279 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story3 B5 245 Beam Dead Force Gravity 0 1 0 2062.9 11.25 11.25
Story3 B6 13 Beam Dead Force Gravity 0 1 0 2901.6 11.25 11.25
Story3 B7 20 Beam Dead Force Gravity 0 1 0 4168 11.25 11.25
Story3 B16 201 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story3 B17 200 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story3 B20 300 Beam Dead Force Gravity 0 1 0 4300 12.15 12.15
Story3 B21 301 Beam Dead Force Gravity 0 1 0 5450 12.15 12.15
Story3 B22 302 Beam Dead Force Gravity 0 1 0 4249.1 12.15 12.15
Story3 B27 246 Beam Dead Force Gravity 0 1 0 5981.1 12.15 12.15
Story3 B14 238 Beam Dead Force Gravity 0 1 0 2483 11.25 11.25
Story3 B29 272 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story3 B25 265 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story3 B10 258 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story3 B26 251 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story3 B32 299 Beam Dead Force Gravity 0 1 0 4150 12.15 12.15
Story3 B8 223 Beam Dead Force Gravity 0 1 0 1118.7 12.15 12.15
Story2 B1 15 Beam Dead Force Gravity 0 1 0 1625 11.25 11.25
Story2 B2 226 Beam Dead Force Gravity 0 1 0 2899.9 11.25 11.25
Story2 B3 280 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story2 B5 240 Beam Dead Force Gravity 0 1 0 2062.9 11.25 11.25
Story2 B6 14 Beam Dead Force Gravity 0 1 0 2901.6 11.25 11.25
Story2 B7 24 Beam Dead Force Gravity 0 1 0 4168 11.25 11.25
Story2 B16 204 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story2 B17 203 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story2 B20 304 Beam Dead Force Gravity 0 1 0 4300 12.15 12.15
Story2 B21 305 Beam Dead Force Gravity 0 1 0 5450 12.15 12.15
Story2 B22 306 Beam Dead Force Gravity 0 1 0 4249.1 12.15 12.15
Story2 B27 227 Beam Dead Force Gravity 0 1 0 5981.1 12.15 12.15
Story2 B14 233 Beam Dead Force Gravity 0 1 0 2483 11.25 11.25
Story2 B29 273 Beam Dead Force Gravity 0 1 0 1850 12.15 12.15
Story2 B25 266 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story2 B10 259 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story2 B26 252 Beam Dead Force Gravity 0 1 0 1800 12.15 12.15
Story2 B32 303 Beam Dead Force Gravity 0 1 0 4150 12.15 12.15
Story2 B8 218 Beam Dead Force Gravity 0 1 0 1118.7 12.15 12.15
Story1 B7 25 Beam Dead Force Gravity 0 1 0 4168 12.15 12.15
Story1 B15 184 Beam Dead Force Gravity 0 1 0 2650 12.15 12.15
Story1 B16 186 Beam Dead Force Gravity 0 1 0 3444.8 12.15 12.15
Story1 B17 185 Beam Dead Force Gravity 0 1 0 785.4 12.15 12.15
Story1 B20 284 Beam Dead Force Gravity 0 1 0 4300 12.15 12.15
Story1 B21 285 Beam Dead Force Gravity 0 1 0 5450 12.15 12.15
Story1 B22 286 Beam Dead Force Gravity 0 1 0 4249.1 12.15 12.15
Story1 B31 282 Beam Dead Force Gravity 0 1 0 5859.6 12.15 12.15
 Absolute Absolute
Relative Relative Force at Force at
Unique Design Load LoadTyp Directio Distance Distance
Story Label Distance Distance Start End
Name Type Pattern e n Start End
Start End kN/m kN/m
mm mm
Story1 B32 283 Beam Dead Force Gravity 0 1 0 4150 12.15 12.15

3.3.2 Area Loads

Table 3.4 - Shell Loads - Uniform

Unique Load Load
Story Label Direction
Name Pattern kN/m²
Story7 F2 4 Dead Gravity 6.5
Story6 F1 7 Dead Gravity 6.5
Story5 F1 8 Dead Gravity 6.5
Story4 F1 9 Dead Gravity 6.5
Story3 F1 10 Dead Gravity 6.5
Story2 F1 11 Dead Gravity 6.5
Story1 F5 30 Dead Gravity 6.5
Story7 F2 4 Live Gravity 1.5
Story6 F1 7 Live Gravity 1.5
Story5 F1 8 Live Gravity 1.5
Story4 F1 9 Live Gravity 1.5
Story3 F1 10 Live Gravity 1.5
Story2 F1 11 Live Gravity 1.5
Story1 F5 30 Live Gravity 1.5

4 Analysis Results
This chapter provides analysis results.

4.1 Structure Results

Table 4.1 - Base Reactions

Load
FX FY FZ MX MY MZ X Y Z
Case/Com
kN kN kN kN-m kN-m kN-m m m m
bo
-
392022.361
Dead -2.399E-05 0 37474.1627 313713.729 0.0003 0 0 0
9
1
Live -2.906E-06 0 3670.1584 38007.4373 -28881.0357 3.959E-05 0 0 0
Wind 1 -409.5748 0 -3.725E-06 -1.76E-05 -4979.9167 3927.0219 0 0 0
Wind 2 8.164E-06 -357.8951 0.0001 4358.3565 -0.0021 -2918.0014 0 0 0
Wind 3 -307.1811 0 1.398E-05 -4.062E-06 -3734.9379 1900.4384 0 0 0
Wind 4 -307.1811 0 -1.957E-05 -2.233E-05 -3734.9372 3990.0945 0 0 0
Wind 5 3.034E-06 -268.4213 0.0001 3268.7674 -0.0018 -3003.4947 0 0 0
Wind 6 9.211E-06 -268.4213 0.0001 3268.7674 -0.0014 -1373.5075 0 0 0
Wind 7 -307.1811 274.1567 -0.0001 -3336.4215 -3734.9359 5180.5699 0 0 0
Wind 8 -300.7541 -268.4213 0.0001 3268.7674 -3659.201 695.1005 0 0 0
Wind 9 -230.5906 205.8003 -0.0001 -2504.5404 -2803.6923 2479.7121 0 0 0
Wind 10 -230.5906 205.8003 -0.0001 -2504.5405 -2803.6915 5298.0502 0 0 0
Wind 11 -225.7661 -201.4949 0.0001 2453.7547 -2746.8406 -857.9168 0 0 0
Wind 12 -225.7661 -201.4949 0.0001 2453.7547 -2746.8398 1901.4944 0 0 0
609643.206
Ult -3.824E-05 0 58336.0813 -485408.878 0.0005 0 0 0
4
 05 September 2019

5 Design Data
This chapter provides design data and results.

5.1 Concrete Frame Design

Table 5.1 - Concrete Frame Preferences - BS 8110-97

Item Value
Multi-Response Step-by-
Design Step - All
# Interaction
24
Curves
# Interaction
11
Points
Minimum
Yes
Eccentricity
Gamma (Steel) 1.05
Gamma
1.5
(Concrete)
Gamma
(Concrete 1.25
Shear)
Pattern Live
0.75
Load Factor
D/C Ratio Limit 1

Table 5.4 - Concrete Column PMM Envelope

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
C3 4TH&ROOF
C13 Story7 Top 155.2726 -24.8586 18.337 Ult 0.243
600*250 8T16
C3 4TH&ROOF
C13 Story7 Bottom 168.8807 17.751 -22.2096 Ult 0.257
600*250 8T16
C3 4TH&ROOF
C15 Story7 Top 114.47 17.3988 6.7809 Ult 0.121
600*250 8T16
C3 4TH&ROOF
C15 Story7 Bottom 128.078 -7.1478 -17.4433 Ult 0.181
600*250 8T16
C3 4TH&ROOF
C16 Story7 Top 95.1391 -13.9225 15.5947 Ult 0.188
600*250 8T16
C3 4TH&ROOF
C16 Story7 Bottom 108.7471 15.7928 -21.3872 Ult 0.255
600*250 8T16
C3 4TH&ROOF
C6 Story7 Top 28.4678 27.4039 0.3558 Ult 0.14
600*250 8T16
C3 4TH&ROOF
C6 Story7 Bottom 42.0758 -5.1173 10.7259 Ult 0.128
600*250 8T16
C3 4TH&ROOF
C8 Story7 Top 142.3001 22.0401 -8.5291 Ult 0.152
600*250 8T16
C3 4TH&ROOF
C8 Story7 Bottom 155.9081 -8.6419 6.206 Ult 0.105
600*250 8T16
C2 4TH&ROOF
C1 Story6 Top 420.9642 -8.4193 8.5097 Ult 0.197
600*250 12T16
C2 4TH&ROOF
C1 Story6 Bottom 433.5642 8.6713 -15.0186 Ult 0.234
600*250 12T16
C2 4TH&ROOF
C2 Story6 Top 452.4511 -15.3462 -15.3411 Ult 0.247
600*250 12T16
C2 4TH&ROOF
C2 Story6 Bottom 465.0511 14.5054 24.5978 Ult 0.303
600*250 12T16
C2 4TH&ROOF
C4 Story6 Top 510.9368 -120.4148 -37.3217 Ult 0.62
600*250 12T16
C2 4TH&ROOF
C4 Story6 Bottom 523.5368 132.5948 55.2793 Ult 0.785
600*250 12T16

Page 18 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
C2 4TH&ROOF
C5 Story6 Top 421.8389 -144.9433 31.2836 Ult 0.654
600*250 12T16
C2 4TH&ROOF
C5 Story6 Bottom 434.4389 178.5475 -44.9135 Ult 0.846
600*250 12T16
C3 4TH&ROOF
C13 Story6 Top 124.2002 -4.5786 15.1277 Ult 0.152
600*250 8T16
C3 4TH&ROOF
C13 Story6 Bottom 137.8084 5.7478 -22.2102 Ult 0.224
600*250 8T16
C3 4TH&ROOF
C15 Story6 Top 385.0299 7.7006 22.2158 Ult 0.286
600*250 8T16
C3 4TH&ROOF
C15 Story6 Bottom 398.6379 -14.0301 -31.6006 Ult 0.363
600*250 8T16
C3 4TH&ROOF
C16 Story6 Top 242.5523 -4.851 17.8418 Ult 0.205
600*250 8T16
C3 4TH&ROOF
C16 Story6 Bottom 256.1603 -5.1232 -26.4567 Ult 0.271
600*250 8T16
C3 4TH&ROOF
C20 Story6 Top 375.5128 55.5417 14.4238 Ult 0.342
600*250 8T16
C3 4TH&ROOF
C20 Story6 Bottom 391.6408 -39.9384 -11.9779 Ult 0.285
600*250 8T16
C3 4TH&ROOF
C21 Story6 Top 157.7134 43.3777 17.11 Ult 0.303
600*250 8T16
C3 4TH&ROOF
C21 Story6 Bottom 171.3214 -48.7624 -20.7267 Ult 0.355
600*250 8T16
C3 4TH&ROOF
C22 Story6 Top 312.9049 -118.3578 -32.2158 Ult 0.713
600*250 8T16
C3 4TH&ROOF
C22 Story6 Bottom 329.0329 80.3309 31.3311 Ult 0.556
600*250 8T16
C3 4TH&ROOF
C24 Story6 Top 327.7139 -47.0489 5.279 Ult 0.258
600*250 8T16
C3 4TH&ROOF
C24 Story6 Bottom 343.8419 33.0265 -4.298 Ult 0.221
600*250 8T16
C3 4TH&ROOF
C25 Story6 Top 117.2456 -7.7493 17.0539 Ult 0.181
600*250 8T16
C3 4TH&ROOF
C25 Story6 Bottom 130.8536 6.3825 -21.5687 Ult 0.221
600*250 8T16
C3 4TH&ROOF
C28 Story6 Top 390.6514 -47.771 -7.9005 Ult 0.289
600*250 8T16
C3 4TH&ROOF
C28 Story6 Bottom 403.2514 55.9625 13.9289 Ult 0.348
600*250 8T16
C2 4TH&ROOF
C29 Story6 Top 458.2025 -25.0353 15.9606 Ult 0.263
600*250 12T16
C2 4TH&ROOF
C29 Story6 Bottom 471.8105 19.2637 -20.5198 Ult 0.287
600*250 12T16
C3 4TH&ROOF
C30 Story6 Top 367.4467 39.4734 -13.2926 Ult 0.285
600*250 8T16
C3 4TH&ROOF
C30 Story6 Bottom 381.0547 -43.2699 17.7348 Ult 0.329
600*250 8T16
C3 4TH&ROOF
C3 Story6 Top 309.2088 40.4956 -6.4033 Ult 0.237
600*250 8T16
C3 4TH&ROOF
C3 Story6 Bottom 322.8168 -41.8922 9.9216 Ult 0.263
600*250 8T16
C3 4TH&ROOF
C6 Story6 Top 317.7907 28.3998 -23.3614 Ult 0.31
600*250 8T16
C3 4TH&ROOF
C6 Story6 Bottom 333.9187 -20.4465 21.956 Ult 0.287
600*250 8T16
C3 4TH&ROOF
C8 Story6 Top 411.5008 28.4622 -5.1438 Ult 0.237
600*250 8T16
C3 4TH&ROOF
C8 Story6 Bottom 425.1089 -32.3881 6.2826 Ult 0.254
600*250 8T16
C9 Story6 C3 4TH&ROOF Top 364.9321 28.3022 12.4106 Ult 0.253

Page 19 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
600*250 8T16
C3 4TH&ROOF
C9 Story6 Bottom 378.5401 -33.7478 -18.0035 Ult 0.303
600*250 8T16
C3 4TH&ROOF
C7 Story6 Top 368.4971 45.0986 -5.245 Ult 0.266
600*250 8T16
C3 4TH&ROOF
C7 Story6 Bottom 382.1051 -53.1456 5.5992 Ult 0.294
600*250 8T16
C2 4TH&ROOF
C11 Story6 Top 407.8806 -9.0158 -6.4193 Ult 0.184
600*250 12T16
C2 4TH&ROOF
C11 Story6 Bottom 421.4886 8.4298 5.5182 Ult 0.184
600*250 12T16
C1 4TH&ROOF
C10 Story6 Top 457.9825 -17.3197 34.0321 Ult 0.372
600*250 10T16
C1 4TH&ROOF
C10 Story6 Bottom 471.5905 10.1483 -41.9192 Ult 0.415
600*250 10T16
C1 4TH&ROOF
C12 Story6 Top 431.5825 55.7789 -19.2672 Ult 0.361
600*250 10T16
C1 4TH&ROOF
C12 Story6 Bottom 445.1955 -55.3006 25.1153 Ult 0.398
600*250 10T16
C1 4TH&ROOF
C14 Story6 Top 504.7654 50.538 -23.9984 Ult 0.392
600*250 10T16
C1 4TH&ROOF
C14 Story6 Bottom 518.377 -50.5124 31.5062 Ult 0.44
600*250 10T16
C3 4TH&ROOF
C27 Story6 Top 300.7705 23.6844 -45.8276 Ult 0.496
600*250 8T16
C3 4TH&ROOF
C27 Story6 Bottom 314.3785 -31.993 53.636 Ult 0.599
600*250 8T16
C2 4TH&ROOF
C31 Story6 Top 407.9662 -109.9084 -41.6366 Ult 0.621
600*250 12T16
C2 4TH&ROOF
C31 Story6 Bottom 424.0942 71.8818 39.2316 Ult 0.491
600*250 12T16
C2 2ND&3rd
C1 Story5 Top 856.967 -7.8732 10.7121 Ult 0.332
700*250 12T16
C2 2ND&3rd
C1 Story5 Bottom 871.667 -17.4333 -18.2588 Ult 0.371
700*250 12T16
C2 2ND&3rd
C2 Story5 Top 921.6258 -18.4325 -13.5578 Ult 0.37
700*250 12T16
C2 2ND&3rd
C2 Story5 Bottom 936.3258 18.7265 27.8784 Ult 0.435
700*250 12T16
C2 2ND&3rd
C4 Story5 Top 1005.0101 -71.6191 -29.8759 Ult 0.505
700*250 12T16
C2 2ND&3rd
C4 Story5 Bottom 1019.7101 127.8073 57.4219 Ult 0.73
700*250 12T16
C2 2ND&3rd
C5 Story5 Top 822.641 -108.1556 25.8479 Ult 0.494
700*250 12T16
C2 2ND&3rd
C5 Story5 Bottom 837.341 179.9322 -48.0377 Ult 0.742
700*250 12T16
C3 2ND&3RD
C13 Story5 Top 83.8378 -10.6855 14.7344 Ult 0.171
600*250 8T16
C3 2ND&3RD
C13 Story5 Bottom 97.4459 7.3424 -21.3613 Ult 0.238
600*250 8T16
C3 2ND&3RD
C15 Story5 Top 651.7549 13.0351 21.966 Ult 0.39
600*250 8T16
C3 2ND&3RD
C15 Story5 Bottom 665.3629 -13.3073 -33.0093 Ult 0.46
600*250 8T16
C3 2ND&3RD
C16 Story5 Top 394.2585 -8.6023 18.8149 Ult 0.269
600*250 8T16
C3 2ND&3RD
C16 Story5 Bottom 407.8665 8.1573 -28.1232 Ult 0.332
600*250 8T16
C3 2ND&3RD
C20 Story5 Top 752.5943 32.1702 19.3007 Ult 0.435
600*250 8T16

Page 20 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
C3 2ND&3RD
C20 Story5 Bottom 768.7223 -36.7787 -17.6923 Ult 0.442
600*250 8T16
C3 2ND&3RD
C21 Story5 Top 331.3346 28.9381 14.6879 Ult 0.256
600*250 8T16
C3 2ND&3RD
C21 Story5 Bottom 344.9426 -45.7519 -20.9767 Ult 0.349
600*250 8T16
C3 2ND&3RD
C22 Story5 Top 647.0878 -60.0994 -31.7283 Ult 0.53
600*250 8T16
C3 2ND&3RD
C22 Story5 Bottom 663.2158 66.3469 32.083 Ult 0.554
600*250 8T16
C3 2ND&3RD
C24 Story5 Top 664.3218 -25.5485 12.3855 Ult 0.36
600*250 8T16
C3 2ND&3RD
C24 Story5 Bottom 680.4498 27.3498 -8.7482 Ult 0.356
600*250 8T16
C3 2ND&3RD
C25 Story5 Top 250.0124 -5.0002 15.643 Ult 0.194
600*250 8T16
C3 2ND&3RD
C25 Story5 Bottom 263.6204 5.2724 -22.0283 Ult 0.241
600*250 8T16
C3 2ND&3RD
C28 Story5 Top 789.0845 -23.6777 -9.8636 Ult 0.399
600*250 8T16
C3 2ND&3RD
C28 Story5 Bottom 801.6845 45.5678 15.4841 Ult 0.461
600*250 8T16
C2 2ND&3rd
C29 Story5 Top 927.2354 -20.115 15.3158 Ult 0.38
700*250 12T16
C2 2ND&3rd
C29 Story5 Bottom 943.1114 19.8906 -24.5312 Ult 0.422
700*250 12T16
C3 2ND&3RD
C30 Story5 Top 750.723 21.5402 -11.3347 Ult 0.385
600*250 8T16
C3 2ND&3RD
C30 Story5 Bottom 764.3311 -36.1145 19.3165 Ult 0.446
600*250 8T16
C3 2ND&3RD
C3 Story5 Top 644.0533 20.8218 -8.0507 Ult 0.328
600*250 8T16
C3 2ND&3RD
C3 Story5 Bottom 657.6613 -36.1359 12.0745 Ult 0.374
600*250 8T16
C3 2ND&3RD
C6 Story5 Top 620.1255 17.0471 -23.2405 Ult 0.388
600*250 8T16
C3 2ND&3RD
C6 Story5 Bottom 636.2535 -20.9854 24.7798 Ult 0.407
600*250 8T16
C3 2ND&3RD
C8 Story5 Top 674.3867 18.1209 -8.4298 Ult 0.338
600*250 8T16
C3 2ND&3RD
C8 Story5 Bottom 687.9948 -29.28 8.5999 Ult 0.362
600*250 8T16
C3 2ND&3RD
C9 Story5 Top 738.6455 14.7729 13.396 Ult 0.382
600*250 8T16
C3 2ND&3RD
C9 Story5 Bottom 752.2535 -26.7484 -20.5589 Ult 0.435
600*250 8T16
C3 2ND&3RD
C7 Story5 Top 765.8803 23.3003 -9.5735 Ult 0.388
600*250 8T16
C3 2ND&3RD
C7 Story5 Bottom 779.4883 -42.1384 10.1818 Ult 0.428
600*250 8T16
C2 2ND&3rd
C11 Story5 Top 835.1673 -11.2106 -10.4396 Ult 0.326
700*250 12T16
C2 2ND&3rd
C11 Story5 Bottom 851.0433 17.0209 11.289 Ult 0.337
700*250 12T16
C1 2ND&3RD
C10 Story5 Top 918.0266 -18.3605 29.5272 Ult 0.436
700*250 12T16
C1 2ND&3RD
C10 Story5 Bottom 933.9026 18.6781 -45.3978 Ult 0.518
700*250 12T16
C1 2ND&3RD
C12 Story5 Top 870.085 35.4237 -17.2839 Ult 0.377
700*250 12T16
C12 Story5 C1 2ND&3RD Bottom 885.9669 -55.7296 27.6366 Ult 0.444

Page 21 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
700*250 12T16
C1 2ND&3RD
C14 Story5 Top 1008.4292 34.0241 -22.2878 Ult 0.443
700*250 12T16
C1 2ND&3RD
C14 Story5 Bottom 1024.3094 -52.3407 35.0469 Ult 0.519
700*250 12T16
C3 2ND&3RD
C27 Story5 Top 624.2953 12.4859 -32.614 Ult 0.442
600*250 8T16
C3 2ND&3RD
C27 Story5 Bottom 637.9033 -22.7632 50.0965 Ult 0.579
600*250 8T16
C2 2ND&3rd
C31 Story5 Top 833.1786 -67.9728 -44.5249 Ult 0.532
700*250 12T16
C2 2ND&3rd
C31 Story5 Bottom 851.9946 68.7864 44.8614 Ult 0.539
700*250 12T16
C2 2ND&3rd
C1 Story4 Top 1279.5992 -14.5866 15.995 Ult 0.497
700*250 12T16
C2 2ND&3rd
C1 Story4 Bottom 1294.2992 25.886 -22.0914 Ult 0.532
700*250 12T16
C2 2ND&3rd
C2 Story4 Top 1379.6275 -12.9774 -17.2453 Ult 0.535
700*250 12T16
C2 2ND&3rd
C2 Story4 Bottom 1394.3275 27.8866 28.9273 Ult 0.593
700*250 12T16
C2 2ND&3rd
C4 Story4 Top 1492.0626 -75.0921 -30.1042 Ult 0.66
700*250 12T16
C2 2ND&3rd
C4 Story4 Bottom 1506.7626 121.3875 58.9474 Ult 0.843
700*250 12T16
C2 2ND&3rd
C5 Story4 Top 1226.9951 -101.1875 28.8692 Ult 0.607
700*250 12T16
C2 2ND&3rd
C5 Story4 Bottom 1241.6951 161.9703 -52.9514 Ult 0.813
700*250 12T16
C3 2ND&3RD
C13 Story4 Top 51.5737 -9.6511 13.0463 Ult 0.165
600*250 8T16
C3 2ND&3RD
C13 Story4 Bottom 65.1819 5.5728 -19.3148 Ult 0.228
600*250 8T16
C3 2ND&3RD
C15 Story4 Top 911.0704 18.2214 22.365 Ult 0.5
600*250 8T16
C3 2ND&3RD
C15 Story4 Bottom 924.6784 -18.4936 -33.7544 Ult 0.568
600*250 8T16
C3 2ND&3RD
C16 Story4 Top 544.2027 -10.8841 18.6112 Ult 0.327
600*250 8T16
C3 2ND&3RD
C16 Story4 Bottom 557.8107 11.1562 -28.2434 Ult 0.389
600*250 8T16
C3 2ND&3RD
C20 Story4 Top 1121.7941 36.9697 24.9126 Ult 0.615
600*250 8T16
C3 2ND&3RD
C20 Story4 Bottom 1137.9221 -40.1102 -21.8976 Ult 0.614
600*250 8T16
C3 2ND&3RD
C21 Story4 Top 500.0267 28.4947 15.9821 Ult 0.319
600*250 8T16
C3 2ND&3RD
C21 Story4 Bottom 513.6347 -45.5758 -22.1604 Ult 0.395
600*250 8T16
C3 2ND&3RD
C22 Story4 Top 973.5796 -73.535 -34.2949 Ult 0.677
600*250 8T16
C3 2ND&3RD
C22 Story4 Bottom 989.7076 69.6722 34.4945 Ult 0.675
600*250 8T16
C3 2ND&3RD
C24 Story4 Top 993.3385 -34.0084 17.2113 Ult 0.527
600*250 8T16
C3 2ND&3RD
C24 Story4 Bottom 1009.4665 29.0794 -12.6183 Ult 0.509
600*250 8T16
C3 2ND&3RD
C25 Story4 Top 378.905 -7.5781 16.0988 Ult 0.245
600*250 8T16
C3 2ND&3RD
C25 Story4 Bottom 392.513 7.8503 -22.0559 Ult 0.288
600*250 8T16

Page 22 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
C3 2ND&3RD
C28 Story4 Top 1175.6497 -28.2831 -14.6956 Ult 0.585
600*250 8T16
C3 2ND&3RD
C28 Story4 Bottom 1188.2497 44.5656 16.4201 Ult 0.62
600*250 8T16
C2 2ND&3rd
C29 Story4 Top 1382.0577 -27.6412 18.2712 Ult 0.547
700*250 12T16
C2 2ND&3rd
C29 Story4 Bottom 1397.9337 27.9587 -29.4799 Ult 0.596
700*250 12T16
C3 2ND&3RD
C30 Story4 Top 1122.1913 25.239 -14.0274 Ult 0.556
600*250 8T16
C3 2ND&3RD
C30 Story4 Bottom 1135.7993 -39.2099 21.6992 Ult 0.611
600*250 8T16
C3 2ND&3RD
C3 Story4 Top 961.6157 24.938 -12.0202 Ult 0.481
600*250 8T16
C3 2ND&3RD
C3 Story4 Bottom 975.2237 -39.825 13.845 Ult 0.516
600*250 8T16
C3 2ND&3RD
C6 Story4 Top 913.6157 21.0104 -26.1968 Ult 0.525
600*250 8T16
C3 2ND&3RD
C6 Story4 Bottom 929.7437 -25.5598 27.8184 Ult 0.544
600*250 8T16
C3 2ND&3RD
C8 Story4 Top 934.3075 17.6321 11.6788 Ult 0.459
600*250 8T16
C3 2ND&3RD
C8 Story4 Bottom 947.9156 -28.9748 11.8489 Ult 0.48
600*250 8T16
C3 2ND&3RD
C9 Story4 Top 1101.2623 22.0252 14.6638 Ult 0.546
600*250 8T16
C3 2ND&3RD
C9 Story4 Bottom 1114.8703 -26.1536 -22.9091 Ult 0.592
600*250 8T16
C3 2ND&3RD
C7 Story4 Top 1149.5387 22.8126 -14.3692 Ult 0.566
600*250 8T16
C3 2ND&3RD
C7 Story4 Bottom 1163.1467 -39.6625 14.6181 Ult 0.595
600*250 8T16
C2 2ND&3rd
C11 Story4 Top 1246.0932 -15.8159 -15.5762 Ult 0.485
700*250 12T16
C2 2ND&3rd
C11 Story4 Bottom 1261.9692 25.2394 15.6596 Ult 0.496
700*250 12T16
C1 2ND&3RD
C10 Story4 Top 1366.8371 -27.3367 32.7182 Ult 0.598
700*250 12T16
C1 2ND&3RD
C10 Story4 Bottom 1382.7131 27.6543 -49.5124 Ult 0.681
700*250 12T16
C1 2ND&3RD
C12 Story4 Top 1295.6694 36.7303 -18.4847 Ult 0.523
700*250 12T16
C1 2ND&3RD
C12 Story4 Bottom 1311.5513 -53.7773 29.7077 Ult 0.585
700*250 12T16
C1 2ND&3RD
C14 Story4 Top 1500.6488 32.4685 -23.8124 Ult 0.611
700*250 12T16
C1 2ND&3RD
C14 Story4 Bottom 1516.5289 -49.1106 37.9324 Ult 0.684
700*250 12T16
C3 2ND&3RD
C27 Story4 Top 934.7661 18.6953 -36.1876 Ult 0.585
600*250 8T16
C3 2ND&3RD
C27 Story4 Bottom 948.3741 -24.2092 53.2299 Ult 0.702
600*250 8T16
C2 2ND&3rd
C31 Story4 Top 1248.6584 -74.9099 -47.9804 Ult 0.671
700*250 12T16
C2 2ND&3rd
C31 Story4 Bottom 1267.4744 69.3335 48.5185 Ult 0.674
700*250 12T16
C2 GR&1st
C1 Story3 Top 1689.0855 -18.3325 21.1136 Ult 0.589
700*250 16T16
C2 GR&1st
C1 Story3 Bottom 1703.7855 34.0757 -22.4968 Ult 0.606
700*250 16T16
C2 Story3 C2 GR&1st Top 1830.3439 -17.5686 -22.8793 Ult 0.637

Page 23 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
700*250 16T16
C2 GR&1st
C2 Story3 Bottom 1845.0439 36.9009 30.4669 Ult 0.678
700*250 16T16
C2 GR&1st
C4 Story3 Top 1974.4969 -76.7958 -29.5004 Ult 0.738
700*250 16T16
C2 GR&1st
C4 Story3 Bottom 1989.1969 140.5719 63.4611 Ult 0.919
700*250 16T16
C2 GR&1st
C5 Story3 Top 1639.291 -98.2488 31.3621 Ult 0.67
700*250 16T16
C2 GR&1st
C5 Story3 Bottom 1653.991 169.8811 -63.4393 Ult 0.878
700*250 16T16
C3 GR&1ST
C13 Story3 Top 28.0612 -10.2654 10.7783 Ult 0.119
600*250 12T16
C3 GR&1ST
C13 Story3 Bottom 41.6693 2.5433 -15.7069 Ult 0.147
600*250 12T16
C3 GR&1ST
C15 Story3 Top 1165.0068 23.3001 21.3764 Ult 0.536
600*250 12T16
C3 GR&1ST
C15 Story3 Bottom 1178.6148 -23.5723 -32.9157 Ult 0.595
600*250 12T16
C3 GR&1ST
C16 Story3 Top 690.9759 -13.8195 17.5108 Ult 0.34
600*250 12T16
C3 GR&1ST
C16 Story3 Bottom 704.5839 -14.0917 -27.1776 Ult 0.394
600*250 12T16
C3 GR&1ST
C20 Story3 Top 1488.1601 32.9632 30.3768 Ult 0.7
600*250 12T16
C3 GR&1ST
C20 Story3 Bottom 1504.2881 -42.1848 -24.8725 Ult 0.687
600*250 12T16
C3 GR&1ST
C21 Story3 Top 664.3303 23.561 16.9227 Ult 0.336
600*250 12T16
C3 GR&1ST
C21 Story3 Bottom 677.9383 -42.0466 -22.6627 Ult 0.392
600*250 12T16
C3 GR&1ST
C22 Story3 Top 1295.3964 -74.6053 -35.531 Ult 0.701
600*250 12T16
C3 GR&1ST
C22 Story3 Bottom 1311.5244 66.1093 36.2616 Ult 0.695
600*250 12T16
C3 GR&1ST
C24 Story3 Top 1319.7628 -37.27 22.2231 Ult 0.604
600*250 12T16
C3 GR&1ST
C24 Story3 Bottom 1335.8908 27.3493 -16.6986 Ult 0.582
600*250 12T16
C3 GR&1ST
C25 Story3 Top 505.2851 -10.1057 16.2711 Ult 0.266
600*250 12T16
C3 GR&1ST
C25 Story3 Bottom 518.8931 10.3779 -21.3085 Ult 0.297
600*250 12T16
C3 GR&1ST
C28 Story3 Top 1552.1458 -30.0707 -19.4018 Ult 0.675
600*250 12T16
C3 GR&1ST
C28 Story3 Bottom 1564.7458 54.3816 19.5593 Ult 0.707
600*250 12T16
C2 GR&1st
C29 Story3 Top 1825.4013 -31.1745 22.8175 Ult 0.642
700*250 16T16
C2 GR&1st
C29 Story3 Bottom 1841.2773 39.3783 -34.3018 Ult 0.691
700*250 16T16
C3 GR&1ST
C30 Story3 Top 1487.8086 21.4051 -18.5976 Ult 0.642
600*250 12T16
C3 GR&1ST
C30 Story3 Bottom 1501.4167 -42.0138 23.9531 Ult 0.682
600*250 12T16
C3 GR&1ST
C3 Story3 Top 1266.9466 22.0093 -15.8368 Ult 0.549
600*250 12T16
C3 GR&1ST
C3 Story3 Bottom 1280.5546 -44.4685 16.0069 Ult 0.579
600*250 12T16
C3 GR&1ST
C6 Story3 Top 1198.5531 23.9711 -27.5713 Ult 0.576
600*250 12T16

Page 24 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
C3 GR&1ST
C6 Story3 Bottom 1214.6811 -30.9699 31.7354 Ult 0.608
600*250 12T16
C3 GR&1ST
C8 Story3 Top 1192.8736 12.5014 -14.9109 Ult 0.512
600*250 12T16
C3 GR&1ST 600*250
C8 Story3 Bottom 1206.4817 -28.7452 15.184 Ult 0.529
12T16
C3 GR&1ST 600*250
C9 Story3 Top 1455.8597 29.1172 14.4864 Ult 0.62
12T16
C3 GR&1ST 600*250
C9 Story3 Bottom 1469.4677 -29.3894 -24.1163 Ult 0.664
12T16
C3 GR&1ST 600*250
C7 Story3 Top 1526.9036 17.0555 -19.0863 Ult 0.656
12T16
C3 GR&1ST 600*250
C7 Story3 Bottom 1540.5116 -36.5943 19.6275 Ult 0.676
12T16
C2 GR&1st 700*250
C11 Story3 Top 1642.5427 -21.5476 -20.5318 Ult 0.575
16T16
C2 GR&1st 700*250
C11 Story3 Bottom 1658.4187 33.1684 20.2687 Ult 0.584
16T16
C1 GR&1ST 800*250
C10 Story3 Top 1805.617 -36.1123 36.3231 Ult 0.631
16T16
C1 GR&1ST 800*250
C10 Story3 Bottom 1823.761 36.4752 -57.0518 Ult 0.707
16T16
C1 GR&1ST 800*250
C12 Story3 Top 1708.8439 37.1384 -21.3605 Ult 0.557
16T16
C1 GR&1ST 800*250
C12 Story3 Bottom 1726.9947 -75.0962 33.3961 Ult 0.617
16T16
C1 GR&1ST 800*250
C14 Story3 Top 1985.3446 39.7069 -25.8861 Ult 0.649
16T16
C1 GR&1ST 800*250
C14 Story3 Bottom 2003.4934 -63.5089 43.0014 Ult 0.718
16T16
C3 GR&1ST 600*250
C27 Story3 Top 1236.676 24.7335 -37.9616 Ult 0.642
12T16
C3 GR&1ST 600*250
C27 Story3 Bottom 1250.284 -25.0057 56.2902 Ult 0.741
12T16
C2 GR&1st 700*250
C31 Story3 Top 1655.5929 -78.0229 -50.4161 Ult 0.722
16T16
C2 GR&1st 700*250
C31 Story3 Bottom 1674.4089 63.0363 51.4046 Ult 0.722
16T16
C2 GR&1st 700*250
C1 Story2 Top 2085.6237 -23.5719 26.0703 Ult 0.728
16T16
C2 GR&1st 700*250
C1 Story2 Bottom 2100.3237 -42.0065 -43.6591 Ult 0.803
16T16
C2 GR&1st 700*250
C2 Story2 Top 2272.1068 -32.6448 -28.4013 Ult 0.796
16T16
C2 GR&1st 700*250
C2 Story2 Bottom 2286.8068 -53.3601 28.5851 Ult 0.812
16T16
C2 GR&1st 700*250
C4 Story2 Top 2459.6433 -87.3874 -36.4 Ult 0.911
16T16
C2 GR&1st 700*250
C4 Story2 Bottom 2474.3433 49.4869 32.383 Ult 0.879
16T16
C2 GR&1st 700*250
C5 Story2 Top 2066.373 -93.5534 39.4735 Ult 0.81
16T16
C2 GR&1st 700*250
C5 Story2 Bottom 2081.073 41.6215 -23.5702 Ult 0.727
16T16
C3 GR&1ST 600*250
C13 Story2 Top 26.4066 -12.3719 7.2414 Ult 0.089
12T16
C3 GR&1ST 600*250
C13 Story2 Bottom 40.0147 0.8003 -11.9622 Ult 0.106
12T16
C3 GR&1ST 600*250
C15 Story2 Top 1412.8594 -28.2572 18.6063 Ult 0.619
12T16
C3 GR&1ST 600*250
C15 Story2 Bottom 1426.4674 -28.5293 -28.4714 Ult 0.667
12T16
C3 GR&1ST
C16 Story2 Top 833.4893 -16.6698 14.9328 Ult 0.382
600*250 12T16
C3 GR&1ST
C16 Story2 Bottom 847.0973 -16.9419 -22.9643 Ult 0.424
600*250 12T16
C3 GR&1ST
C20 Story2 Top 1855.021 37.1004 37.8691 Ult 0.87
600*250 12T16
C20 Story2 C3 GR&1ST Bottom 1871.149 -38.424 -31.7107 Ult 0.85

Page 25 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
600*250 12T16
C3 GR&1ST
C21 Story2 Top 824.3382 16.4868 19.046 Ult 0.397
600*250 12T16
C3 GR&1ST
C21 Story2 Bottom 837.9462 -31.8307 -23.1683 Ult 0.434
600*250 12T16
C3 GR&1ST
C22 Story2 Top 1613.9774 -88.0022 -32.9497 Ult 0.821
600*250 12T16
C3 GR&1ST
C22 Story2 Bottom 1630.1054 72.3488 30.5687 Ult 0.795
600*250 12T16
C3 GR&1ST
C24 Story2 Top 1645.1247 -46.6847 29.8166 Ult 0.763
600*250 12T16
C3 GR&1ST
C24 Story2 Bottom 1661.2527 31.8963 -20.7657 Ult 0.722
600*250 12T16
C3 GR&1ST
C25 Story2 Top 631.0402 -15.1323 17.8483 Ult 0.322
600*250 12T16
C3 GR&1ST
C25 Story2 Bottom 644.6482 12.893 -21.4632 Ult 0.343
600*250 12T16
C3 GR&1ST
C28 Story2 Top 1917.7002 -38.9308 23.9713 Ult 0.835
600*250 12T16
C3 GR&1ST
C28 Story2 Bottom 1930.3002 -23.9232 -24.1288 Ult 0.831
600*250 12T16
C2 GR&1st
C29 Story2 Top 2257.0999 -32.2568 28.2137 Ult 0.791
700*250 16T16
C2 GR&1st
C29 Story2 Bottom 2272.9759 -46.2115 -31.9744 Ult 0.816
700*250 16T16
C3 GR&1ST
C30 Story2 Top 1846.1449 9.3892 -23.0768 Ult 0.786
600*250 12T16
C3 GR&1ST
C30 Story2 Bottom 1859.7529 -37.1951 23.7207 Ult 0.811
600*250 12T16
C3 GR&1ST
C3 Story2 Top 1555.0547 31.1011 16.9117 Ult 0.667
600*250 12T16
C3 GR&1ST
C3 Story2 Bottom 1568.6627 -33.9205 19.6083 Ult 0.684
600*250 12T16
C3 GR&1ST
C6 Story2 Top 1470.9832 29.4197 -27.9141 Ult 0.681
600*250 12T16
C3 GR&1ST
C6 Story2 Bottom 1487.1112 -34.5187 18.5889 Ult 0.651
600*250 12T16
C3 GR&1ST
C8 Story2 Top 1450.5616 1.3565 -18.132 Ult 0.614
600*250 12T16
C3 GR&1ST
C8 Story2 Bottom 1464.1697 -29.2834 18.7369 Ult 0.639
600*250 12T16
C3 GR&1ST
C9 Story2 Top 1805.737 -1.049 22.5717 Ult 0.764
600*250 12T16
C3 GR&1ST
C9 Story2 Bottom 1819.345 -36.3869 -22.3849 Ult 0.79
600*250 12T16
C3 GR&1ST
C7 Story2 Top 1897.9172 37.9583 -21.1763 Ult 0.816
600*250 12T16
C3 GR&1ST
C7 Story2 Bottom 1911.5252 -38.2305 26.9213 Ult 0.845
600*250 12T16
C2 GR&1st
C11 Story2 Top 2025.7399 -40.5148 -24.5493 Ult 0.713
700*250 16T16
C2 GR&1st
C11 Story2 Bottom 2041.6159 -50.054 25.5202 Ult 0.726
700*250 16T16
C1 GR&1ST
C10 Story2 Top 2236.2552 -44.7251 33.0441 Ult 0.743
800*250 16T16
C1 GR&1ST
C10 Story2 Bottom 2254.3992 -61.5285 -59.9755 Ult 0.845
800*250 16T16
C1 GR&1ST
C12 Story2 Top 2108.9021 12.8825 -26.3613 Ult 0.673
800*250 16T16
C1 GR&1ST
C12 Story2 Bottom 2127.0528 -69.2455 30.9748 Ult 0.716
800*250 16T16

Page 26 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
C1 GR&1ST
C14 Story2 Top 2462.9814 5.9074 -30.7873 Ult 0.782
800*250 16T16
C1 GR&1ST
C14 Story2 Bottom 2481.1301 -57.955 40.9705 Ult 0.842
800*250 16T16
C3 GR&1ST
C27 Story2 Top 1530.3395 30.6068 -42.6686 Ult 0.772
600*250 12T16
C3 GR&1ST
C27 Story2 Bottom 1543.9475 -50.5242 56.5827 Ult 0.864
600*250 12T16
C2 GR&1st
C31 Story2 Top 2056.4367 -93.4386 -48.6732 Ult 0.839
700*250 16T16
C2 GR&1st
C31 Story2 Bottom 2075.2527 70.7399 49.8686 Ult 0.835
700*250 16T16
C2 Sh 700*300
C1 Story1 Top 2202.0898 44.0418 40.4075 Ult 0.704
16T16
C2 Sh 700*300
C1 Story1 Bottom 2219.7298 -39.2461 -33.2959 Ult 0.69
16T16
C2 Sh 700*300
C2 Story1 Top 2474.907 32.9294 37.1236 Ult 0.765
16T16
C2 Sh 700*300
C2 Story1 Bottom 2492.7555 -35.5156 37.3913 Ult 0.772
16T16
C2 Sh 700*300
C4 Story1 Top 2549.3846 21.0375 38.2408 Ult 0.784
16T16
C2 Sh 700*300
C4 Story1 Bottom 2567.1304 -32.0415 38.507 Ult 0.793
16T16
C2 Sh 700*300
C5 Story1 Top 2112.3455 18.8022 -31.6852 Ult 0.65
16T16
C2 Sh 700*300
C5 Story1 Bottom 2129.986 -27.5112 31.9498 Ult 0.658
16T16
C3 Sh 600*300
C13 Story1 Top 105.102 -10.7602 7.2257 Ult 0.072
12T16
C3 Sh 600*300
C13 Story1 Bottom 120.2221 -6.0605 -7.7594 Ult 0.07
12T16
C3 Sh 600*300
C15 Story1 Top 1668.3237 -14.4953 25.0249 Ult 0.629
12T16
C3 Sh 600*300
C15 Story1 Bottom 1683.4437 -11.7321 -25.2517 Ult 0.633
12T16
C3 Sh 600*300
C16 Story1 Top 1001.1721 -20.0234 14.1787 Ult 0.382
12T16
C3 Sh 600*300
C16 Story1 Bottom 1016.2921 -20.3258 -15.0797 Ult 0.389
12T16
C3 Sh 600*300
C20 Story1 Top 2224.969 44.4994 39.573 Ult 0.867
12T16
C3 Sh 600*300
C20 Story1 Bottom 2243.113 -22.8987 -33.6467 Ult 0.847
12T16
C3 Sh 600*300
C21 Story1 Top 980.9621 19.6192 22.5852 Ult 0.398
12T16
C3 Sh 600*300
C21 Story1 Bottom 996.0821 -16.0332 -14.9412 Ult 0.378
12T16
C3 Sh 600*300
C22 Story1 Top 1949.0635 -89.9008 -29.236 Ult 0.806
12T16
C3 Sh 600*300
C22 Story1 Bottom 1967.2075 33.0808 29.5081 Ult 0.748
12T16
C3 Sh 600*300
C24 Story1 Top 1969.7273 -49.9792 31.5101 Ult 0.77
12T16
C3 Sh 600*300
C24 Story1 Bottom 1987.8713 12.0806 -29.8181 Ult 0.747
12T16
C3 Sh 600*300
C25 Story1 Top 758.768 -20.417 21.9264 Ult 0.325
12T16
C3 Sh 600*300
C25 Story1 Bottom 773.888 15.4778 -11.0924 Ult 0.296
12T16
C28 Story1 C3 Sh 600*300 Top 2068.1017 38.5257 31.0215 Ult 0.79

Page 27 of 50
 05 September 2019

PMM
P M Major M Minor PMM
Label Story Section Location Ratio or
kN kN-m kN-m Combo
Rebar %
12T16
C3 Sh 600*300
C28 Story1 Bottom 2086.2457 -28.6748 31.2937 Ult 0.791
12T16
C2 Sh 700*300
C29 Story1 Top 2513.4634 40.1494 -37.702 Ult 0.78
16T16
C2 Sh 700*300
C29 Story1 Bottom 2531.1034 -48.4038 -37.9666 Ult 0.788
16T16
C3 Sh 600*300
C30 Story1 Top 2235.1196 -8.435 -33.5268 Ult 0.838
12T16
C3 Sh 600*300
C30 Story1 Bottom 2253.2636 -45.0653 27.8107 Ult 0.851
12T16
C3 Sh 600*300
C3 Story1 Top 1889.4305 -37.7886 22.5651 Ult 0.712
12T16
C3 Sh 600*300
C3 Story1 Bottom 1907.5745 -17.7429 28.6136 Ult 0.719
12T16
C3 Sh 600*300
C6 Story1 Top 1716.7621 34.3352 24.6994 Ult 0.656
12T16
C3 Sh 600*300
C6 Story1 Bottom 1734.9061 -20.0976 26.0236 Ult 0.656
12T16
C3 Sh 600*300
C8 Story1 Top 1732.8506 -15.1934 -25.9928 Ult 0.653
12T16
C3 Sh 600*300
C8 Story1 Bottom 1747.9707 -6.4166 26.2196 Ult 0.655
12T16
C3 Sh 600*300
C9 Story1 Top 2152.9944 -13.0137 -32.2949 Ult 0.809
12T16
C3 Sh 600*300
C9 Story1 Bottom 2168.1144 -16.4161 -32.5217 Ult 0.816
12T16
C3 Sh 600*300
C7 Story1 Top 2252.4701 -45.0494 -26.9729 Ult 0.849
12T16
C3 Sh 600*300
C7 Story1 Bottom 2267.5901 -17.9974 34.0139 Ult 0.854
12T16
C2 Sh 700*300
C11 Story1 Top 2223.6658 35.3328 -33.355 Ult 0.69
16T16
C2 Sh 700*300
C11 Story1 Bottom 2241.3058 -43.8866 33.6196 Ult 0.698
16T16
C1 Sh 800*300
C10 Story1 Top 2536.6162 50.7323 43.2857 Ult 0.736
16T16
C1 Sh 800*300
C10 Story1 Bottom 2556.7762 -50.0553 -38.3516 Ult 0.729
16T16
C1 Sh 800*300
C12 Story1 Top 2513.4985 -2.1784 -37.7025 Ult 0.703
16T16
C1 Sh 800*300
C12 Story1 Bottom 2533.6666 -24.6792 38.005 Ult 0.715
16T16
C1 Sh 800*300
C14 Story1 Top 2929.0763 -8.187 -43.9361 Ult 0.821
16T16
C1 Sh 800*300
C14 Story1 Bottom 2949.242 -25.1192 44.2386 Ult 0.832
16T16
C3 Sh 600*300
C27 Story1 Top 1746.4546 34.9291 -52.0254 Ult 0.746
12T16
C3 Sh 600*300
C27 Story1 Bottom 1761.5746 -35.2315 32.467 Ult 0.69
12T16
C2 Sh 700*300
C31 Story1 Top 2449.4626 -99.2598 -41.3357 Ult 0.809
16T16
C2 Sh 700*300
C31 Story1 Bottom 2470.6306 30.248 37.0595 Ult 0.763
16T16

Page 28 of 50
 05 September 2019

Columns layout

Short Columns Design (Capacity Ratio)

Page 29 of 50
 05 September 2019

Shear wall design:

This chapter provides design data and results.

1.1 Shear Wall Design

Table 1.1 - Shear Wall Preferences - BS 8110-97

Item Value
Rebar Material fy460
Rebar Shear
fy460
Material
Gamma (Steel) 1.5
Gamma
1.05
(Concrete)
Gamma
(Concrete 1.25
Shear)
# Interaction
24
Curves
# Interaction
11
Points
Edge Design
0.06
PT-Max
Edge Design
0.04
PC-Max
Section Design
0.04
IP-Max
Section Design
0.004
IP-Min
D/C Ratio Limit 0.95

Table 1.2 - Shear Wall Pier Summary - BS 8110-97 (Part 1 of 2)

Rebar
Pier Design Edge End D/C Leg X1 Leg Y1 Leg X2 Leg Y2
Story Station Spacing Pier Leg
Label Type Rebar Rebar Ratio mm mm mm mm
mm
Story7 P1 Top Uniform 12 12 150 0.1 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story7 P1 Bottom Uniform 12 12 150 0.089 15218.9 9316.2 18174.1 9316.2
Leg 1
Story6 P1 Top Uniform 12 12 150 0.16 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story6 P1 Bottom Uniform 12 12 150 0.142 15218.9 9316.2 18174.1 9316.2
Leg 1
Story5 P1 Top Uniform 12 12 150 0.224 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story5 P1 Bottom Uniform 12 12 150 0.155 15218.9 9316.2 18174.1 9316.2
Leg 1
Story4 P1 Top Uniform 12 12 150 0.232 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story4 P1 Bottom Uniform 12 12 150 0.191 15218.9 9316.2 18174.1 9316.2
Leg 1
Story3 P1 Top Uniform 12 12 150 0.242 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story3 P1 Bottom Uniform 12 12 150 0.29 15218.9 9316.2 18174.1 9316.2
Leg 1
Story2 P1 Top Uniform 12 12 150 0.3 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story2 P1 Bottom Uniform 12 12 150 0.364 15218.9 9316.2 18174.1 9316.2
Leg 1
Story1 P1 Top Uniform 12 12 150 0.327 Top Leg 1 15218.9 9316.2 18174.1 9316.2
Bottom
Story1 P1 Bottom Uniform 12 12 150 0.518 15218.9 9316.2 18174.1 9316.2
Leg 1
Story7 P2 Top Uniform 12 12 150 0.063 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Bottom
Story7 P2 Bottom Uniform 12 12 150 0.153 18174.1 7524.1 18174.1 9316.2
Leg 1
Story6 P2 Top Uniform 12 12 150 0.277 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Story6 P2 Bottom Uniform 12 12 150 0.137 Bottom 18174.1 7524.1 18174.1 9316.2

Page 30 of 50
 05 September 2019

Rebar
Pier Design Edge End D/C Leg X1 Leg Y1 Leg X2 Leg Y2
Story Station Spacing Pier Leg
Label Type Rebar Rebar Ratio mm mm mm mm
mm
Leg 1
Story5 P2 Top Uniform 12 12 150 0.152 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Bottom
Story5 P2 Bottom Uniform 12 12 150 0.168 18174.1 7524.1 18174.1 9316.2
Leg 1
Story4 P2 Top Uniform 12 12 150 0.159 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Bottom
Story4 P2 Bottom Uniform 12 12 150 0.235 18174.1 7524.1 18174.1 9316.2
Leg 1
Story3 P2 Top Uniform 12 12 150 0.202 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Bottom
Story3 P2 Bottom Uniform 12 12 150 0.412 18174.1 7524.1 18174.1 9316.2
Leg 1
Story2 P2 Top Uniform 12 12 150 0.421 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Bottom
Story2 P2 Bottom Uniform 12 12 150 0.545 18174.1 7524.1 18174.1 9316.2
Leg 1
Story1 P2 Top Uniform 12 12 150 0.631 Top Leg 1 18174.1 7524.1 18174.1 9316.2
Bottom
Story1 P2 Bottom Uniform 12 12 150 0.764 18174.1 7524.1 18174.1 9316.2
Leg 1
Story7 P3 Top Uniform 12 12 150 0.123 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story7 P3 Bottom Uniform 12 12 150 0.193 15218.9 7524.1 18174.1 7524.1
Leg 1
Story6 P3 Top Uniform 12 12 150 0.159 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story6 P3 Bottom Uniform 12 12 150 0.129 15218.9 7524.1 18174.1 7524.1
Leg 1
Story5 P3 Top Uniform 12 12 150 0.175 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story5 P3 Bottom Uniform 12 12 150 0.201 15218.9 7524.1 18174.1 7524.1
Leg 1
Story4 P3 Top Uniform 12 12 150 0.248 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story4 P3 Bottom Uniform 12 12 150 0.278 15218.9 7524.1 18174.1 7524.1
Leg 1
Story3 P3 Top Uniform 12 12 150 0.332 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story3 P3 Bottom Uniform 12 12 150 0.391 15218.9 7524.1 18174.1 7524.1
Leg 1
Story2 P3 Top Uniform 12 12 150 0.456 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story2 P3 Bottom Uniform 12 12 150 0.561 15218.9 7524.1 18174.1 7524.1
Leg 1
Story1 P3 Top Uniform 12 12 150 0.491 Top Leg 1 15218.9 7524.1 18174.1 7524.1
Bottom
Story1 P3 Bottom Uniform 12 12 150 0.557 15218.9 7524.1 18174.1 7524.1
Leg 1

Page 31 of 50
 05 September 2019

ETABS 2016 Shear Wall Design

BS 8110-97 Pier Design

Story ID Pier ID Centroid X (mm) Centroid Y (mm) Length (mm) Thickness (mm) LLRF
Story1 P2 18174.1 8420.2 1792.1 200 0.6

Material Properties
Ec (MPa) fcu (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
24855.58 25 1 460 460

Design Code Parameters

ɣC ɣS ɣM IPMAX IPMIN PMAX
1.5 1.05 1.25 0.04 0.004 0.8

Pier Leg Location, Length and Thickness

Station Left X1 Left Y1 Right X2 Right Y2 Length Thickness
ID
Location mm mm mm mm mm mm
Top Leg 1 18174.1 7524.1 18174.1 9316.2 1792.1 200
Bottom Leg 1 18174.1 7524.1 18174.1 9316.2 1792.1 200

Flexural Design for N, M3 and M2

N M2 M3
Station D/C Flexural
kN kN-m kN-m
Top 0.631 UDWal8 -479.1967 1.4378 -268.9196
Bottom 0.764 UDWal8 -453.3903 -0.0411 -422.963

Shear Design
Station Rebar N M V Vc Vtotal
ID Shear Combo
Location mm²/m kN kN-m kN kN kN
Top Leg 1 298.31 UDWal6 -363.0684 22.8797 187.3682 0 187.3682
Bottom Leg 1 298.31 UDWal6 -326.9395 249.159 187.3682 0 187.3682

Page 32 of 50
 05 September 2019

Slab Design

Figure 1: Slab 3-D model

Page 33 of 50
 05 September 2019

1. Model geometry
This section provides model geometry information, including items such as joint coordinates, joint
restraints, and element connectivity.

1.1. Connectivity
2. Model properties
This section provides model properties, including items such as material properties, section properties,
and support properties.

2.1. Material properties

Table 1: Material Properties 03 - Concrete, Part 1 of 2

Table 1: Material Properties 03 - Concrete, Part 1 of 2
Material E U A UnitWt Fc LtWtConc UserModRu
p
N/mm2 1/C kN/m3 N/mm2
CSAC30 26667.31234 0.200000 9.9000E-06 2.3563E+01 30.00000 No No
MAT1 24855.58000 0.200000 9.9000E-06 2.4000E+01 25.00000 No Yes
MAT4 24855.58000 0.200000 9.9000E-06 0.0000E+00 25.00000 No No
MAT5 24855.58000 0.200000 9.9000E-06 2.4000E+01 27.50000 No No

Table 1: Material Properties 03 - Concrete, Part 2 of 2

Table 1: Material Properties 03
- Concrete, Part 2 of 2
Material ModRup
N/mm2
CSAC30
MAT1 2.21000
MAT4
MAT5

Table 2: Material Properties 04 - Rebar

Table 2: Material Properties 04 - Rebar
Material E UnitWt Fy Fu
N/mm2 kN/m3 N/mm2 N/mm2
FY 460 200000 7.6973E+01 460.00000 575.00000
MAT2 200000 7.6973E+01 460.00000 575.00000
MAT3 200000 7.6973E+01 250.00000 312.50000

2.2. Section propertie

Table 4: Slab Properties 02 - Solid Slabs
Table 4: Slab Properties 02 - Solid Slabs
Slab Type MatProp Thickness Ortho
mm
Col_Stiff Stiff MAT5 230.000 No
FLAT Slab 230 Slab MAT1 230.000 No
SLAB1 Slab CSAC30 200.000 No

Page 34 of 50
 05 September 2019

Table 5: Beam Properties 02 - Rectangular Beam

Table 5: Beam Properties 02 - Rectangular Beam
Beam MatProp Depth WidthTop WidthBot
mm mm mm
B 0.5*0.25 MAT1 500.000 250.000 250.000
B 0.6*0.25 MAT1 600.000 250.000 250.000
BEAM1 CSAC30 600.000 300.000 300.000

Table 6: Beam Properties 06 - Design Data

Table 6: Beam Properties 06 - Design Data
Beam MatRebarL MatRebarS FlngWOpt CoverTop CoverBot NoDesign
mm mm
B 0.5*0.25 MAT2 MAT3 Analysis 50.000 50.000 No
Property
B 0.6*0.25 MAT2 MAT3 Analysis 61.000 61.000 No
Property
BEAM1 FY 460 FY 460 Analysis 75.000 75.000 No
Property

4. Model loading
This section provides model loading information, including load patterns, load cases, and load
combinations.

4.1. Load patterns

Table 18: Load Patterns

Table 18: Load Patterns
LoadPat Type SelfWtMult

Dead DEAD 1.000000

Live REDUCIBLE LIVE 0.000000

Table 19: Load Assignments - Surface Loads

Table 19: Load Assignments - Surface Loads
Area LoadPat Dir UnifLoad A B C
kN/m2 kN/m3 kN/m3 kN/m2
F1 Dead Gravity 6.50 0.0000E+00 0.0000E+00 0.00
F1 Live Gravity 1.50 0.0000E+00 0.0000E+00 0.00

Table 20: Load Assignments - Line Objects - Distributed Loads, Part 1 of 2

Table 20: Load Assignments - Line Objects - Distributed Loads, Part 1 of 2
Line LoadPat Type Dir RelDistA RelDistB AbsDistA AbsDistB
m m
B15 Dead Force Gravity 0.0000 1.0000 0.00000 2.64998
B17 Dead Force Gravity 0.0000 1.0000 0.00000 0.78537
B16 Dead Force Gravity 0.0000 1.0000 0.00000 3.44482
B6 Dead Force Gravity 0.0000 1.0000 0.00000 2.90158
B7 Dead Force Gravity 0.0000 1.0000 0.00000 4.16801
B11 Dead Force Gravity 0.0000 1.0000 0.00000 1.07500
B10 Dead Force Gravity 0.0000 1.0000 0.00000 1.07500
B1 Dead Force Gravity 0.0000 1.0000 0.00000 1.62500
B2 Dead Force Gravity 0.0000 1.0000 0.00000 2.89986
B4 Dead Force Gravity 0.0000 1.0000 0.00000 2.56301

Page 35 of 50
 05 September 2019

Table 20: Load Assignments - Line Objects - Distributed Loads, Part 1 of 2

Line LoadPat Type Dir RelDistA RelDistB AbsDistA AbsDistB
m m
B5 Dead Force Gravity 0.0000 1.0000 0.00000 2.06286
B24 Dead Force Gravity 0.0000 1.0000 0.00000 1.85000
B18 Dead Force Gravity 0.0000 1.0000 0.00000 1.85000
B12 Dead Force Gravity 0.0000 1.0000 0.00000 2.09999
B8 Dead Force Gravity 0.0000 1.0000 0.00000 1.85000
B3 Dead Force Gravity 0.0000 1.0000 0.00000 1.85000
B23 Dead Force Gravity 0.0000 1.0000 0.00000 4.10001
B20 Dead Force Gravity 0.0000 1.0000 0.00000 4.30000
B21 Dead Force Gravity 0.0000 1.0000 0.00000 5.45000
B22 Dead Force Gravity 0.0000 1.0000 0.00000 4.24906
53 Dead Force Gravity 0.0000 1.0000 0.00000 5.98107
54 Dead Force Gravity 0.0000 1.0000 0.00000 22.40085
55 Dead Force Gravity 0.0000 1.0000 0.00000 4.31962

Table 20: Load Assignments - Line Objects - Distributed Loads, Part 2 of 2

Table 20: Load Assignments - Line Objects - Distributed Loads, Part
2 of 2
Line LoadPat FOverLA FOverLB
kN/m kN/m
B15 Dead 12.15 12.15
B17 Dead 12.15 12.15
B16 Dead 12.15 12.15
B6 Dead 9.00 9.00
B7 Dead 9.00 9.00
B11 Dead 12.15 12.15
B10 Dead 12.15 12.15
B1 Dead 9.00 9.00
B2 Dead 9.00 9.00
B4 Dead 9.00 9.00
B5 Dead 9.00 9.00
B24 Dead 12.15 12.15
B18 Dead 9.00 9.00
B12 Dead 9.00 9.00
B8 Dead 9.00 9.00
B3 Dead 9.00 9.00
B23 Dead 12.15 12.15
B20 Dead 12.15 12.15
B21 Dead 12.15 12.15
B22 Dead 12.15 12.15
53 Dead 9.00 9.00
54 Dead 9.00 9.00
55 Dead 9.00 9.00

4.2. Load cases

Table 21: Load Cases 02 - Static

Table 21: Load Cases 02 - Static
LoadCase InitialCond AType RelForceTol CreepCoeff ShrinkStrn

Dead Zero Linear

Live Zero Linear
D+L UNCR Zero Linear

Page 36 of 50
 05 September 2019

Table 21: Load Cases 02 - Static

LoadCase InitialCond AType RelForceTol CreepCoeff ShrinkStrn

D+0.25L LONG Zero Long Term 0.000010 3.000000 0.000500

TERM Cracked
D+0.25L CR Zero Cracked 0.000010

Table 22: Load Cases 06 - Loads Applied

Table 22: Load Cases 06 - Loads Applied
LoadCase LoadPat SF

Dead Dead 1.000000

Live Live 1.000000
D+L UNCR Dead 1.000000
D+L UNCR Live 1.000000
D+0.25L LONG Dead 1.000000
TERM
D+0.25L LONG Live 0.250000
TERM
D+0.25L CR Dead 1.000000
D+0.25L CR Live 0.250000

4.3. Load combinations

Table 23: Load Combinations
Table 23: Load Combinations
Combo Load SF Type DSStrength DSServInit DSServNorm DSServLong

LONGTERM D+L UNCR 1.00000 Linear Add No No No No

0
LONGTERM D+0.25L LONG 1.00000
TERM 0
LONGTERM D+0.25L CR -
1.00000
0
service Dead 1.00000 Linear Add Yes No No No
0
service Live 1.00000
0
Ult Dead 1.40000 Linear Add Yes No No No
0
Ult Live 1.60000
0

Page 37 of 50
 05 September 2019

Analysis Results

Figure 2: Deformed shape

Page 38 of 50
 05 September 2019

5. Analysis results
5.1. Support results
This section provides support results, including items such as column, support, and spring reactions, .

Table 24: Integrated Wall Forces

Table 24: Integrated Wall Forces
Area OutputCase CaseType Fx Fy Fz Mx My Mz
kN kN kN kN-m kN-m kN-m
31 Ult Combination 29.359 -3.076 419.975 2.0925 177.9716 7.2619
32 Ult Combination 0.420 91.331 -125.776 -120.9826 1.1450 -0.7181
33 Ult Combination 80.608 5.894 22.587 -8.4457 337.3941 -1.6985

5.2. Structure results

Table 25: Sum Of Reactions, Part 1 of 2
Table 25: Sum Of Reactions, Part 1 of 2
OutputCase GlobalFX GlobalFY GlobalFZ GlobalMX GlobalMY GlobalMZ
kN kN kN kN-m kN-m kN-m
Ult -3.465E-005 -3.539E-006 9484.989 96877.8781 -72808.8378 5.157E-004

Table 25: Sum Of Reactions, Part 2 of 2

Table 25: Sum Of Reactions, Part 2 of 2
OutputCase GlobalX GlobalY GlobalZ
m m m
Ult 0.00000 0.00000 0.00000

Page 39 of 50
 05 September 2019

Design

Figure 3: Finite element model

Page 40 of 50
 05 September 2019

6. Design summary
This section provides design information for beams, strips, and punching checks.

6.1. Preferences
Table 26: Design Preferences 01 - Resistance Factors
Table 26: Design Preferences 01 -
Resistance Factors
GammaStee GammaCon GammaShe
l c ar

0E+000 0E+000 0E+000

Table 27: Design Preferences 02 - Rebar Cover - Slabs

Table 27: Design Preferences 02 - Rebar Cover - Slabs
CoverTop CoverBot BarSize InnerLayer PTCGSTop PTCGSBotE PTCGSBotI SlabType
xt nt
mm mm mm mm mm
25.000 25.000 16 B 25.000 40.000 25.000 Two Way

Table 28: Design Preferences 03 - Rebar Cover - Beams

Table 28: Design Preferences 03 - Rebar Cover - Beams
CoverTop CoverBot BarSizeF BarSizeS PTCGSTop PTCGSBot
mm mm mm mm
25.000 25.000 16 8 50.000 50.000

6.4. Beam design

Table 33: Concrete Beam Design Summary 01 - Flexural And Shear Data, Part 1
of 3
Table 33: Concrete Beam Design Summary 01 - Flexural And Shear Data, Part 1 of 3
Line SpanID Location FTopCombo FTopMomen FTopArea
t
kN-m mm2
53 Span 1 Start Ult -28.4257 149.284
56 Span 1 Start Ult -69.5368 371.225
56 Span 1 Middle Ult -2.8755 17.353
56 Span 1 End Ult -74.0992 406.760
57 Span 1 Start Ult -58.7883 319.057
57 Span 1 Middle Ult -0.6508 7.174
57 Span 1 End Ult -61.9188 328.419
B1 Span 1 Start Ult -2.3578 9.645
B1 Span 1 Middle Ult -10.2826 43.474
B1 Span 1 End Ult -60.5415 268.236
B2 Span 1 Start Ult -0.8418 0.000
B2 Span 1 Middle Ult -62.2253 271.733
B2 Span 1 End Ult -118.7157 542.273
B3 Span 1 Start Ult -2.1006 9.424
B3 Span 1 Middle Ult -36.2632 184.915
B3 Span 1 End Ult -86.9713 476.856
B4 Span 1 Start Ult -1.7987 0.000
B4 Span 1 Middle Ult -102.0271 453.566
B4 Span 1 End Ult -139.2084 642.221
B5 Span 1 Start Ult -9.1374 37.252
B5 Span 1 Middle Ult -111.7941 500.884

Page 41 of 50
 05 September 2019

Table 33: Concrete Beam Design Summary 01 - Flexural And Shear Data, Part 1 of 3
Line SpanID Location FTopCombo FTopMomen FTopArea
t
kN-m mm2
B5 Span 1 End Ult -144.9814 671.693
B6 Span 1 Start Ult -30.8221 131.674
B6 Span 1 Middle Ult -189.6769 920.725
B6 Span 1 End Ult -240.2999 1236.007
B7 Span 1 Start Ult -158.4428 773.563
B7 Span 1 Middle Ult -79.9500 380.392
B8 Span 1 Start Ult -1.0796 0.000
B8 Span 1 Middle Ult -36.5999 186.644
B8 Span 1 End Ult -94.4743 523.061
B9 Span 1 Start Ult -40.3048 208.523
B9 Span 1 Middle Ult -11.4653 64.357
B9 Span 1 End Ult -0.2129 0.000
B10 Span 1 Start Ult -15.7552 78.417
B10 Span 1 Middle Ult -31.8659 164.558
B10 Span 1 End Ult -57.2314 304.888
B11 Span 1 Start Ult -20.1747 100.201
B11 Span 1 Middle Ult -35.0510 181.301
B11 Span 1 End Ult -68.2945 368.119
B12 Span 1 Start Ult -1.6916 7.831
B12 Span 1 Middle Ult -36.1464 185.185
B12 Span 1 End Ult -92.6215 512.425
B15 Span 1 Start Ult -4.5093 12.868
B15 Span 1 End Ult -11.6755 48.297
B16 Span 1 Start Ult -46.9088 255.900
B16 Span 1 Middle Ult -21.5956 120.706
B16 Span 1 End Ult -1.3398 15.795
B17 Span 1 Start Ult -3.2712 16.627
B17 Span 1 Middle Ult -16.7076 87.113
B17 Span 1 End Ult -5.5262 29.628
B18 Span 1 Middle Ult -36.0534 184.521
B18 Span 1 End Ult -106.3852 599.216
B20 Span 1 Start Ult -34.4105 175.547
B20 Span 1 End Ult -60.2811 318.920
B21 Span 1 Start Ult -71.6860 382.833
B21 Span 1 End Ult -66.6325 357.992
B22 Span 1 Start Ult -73.7505 399.673
B23 Span 1 Start Ult -69.7590 380.972
B23 Span 1 Middle Ult -16.0399 84.876
B23 Span 1 End Ult -30.0594 155.642
B24 Span 1 Start Ult -7.6631 39.096
B24 Span 1 Middle Ult -34.9863 181.463
B24 Span 1 End Ult -81.2054 445.025

Page 42 of 50
 05 September 2019

Table 33: Concrete Beam Design Summary 01 - Flexural And Shear Data, Part 2
of 3
Table 33: Concrete Beam Design Summary 01 - Flexural And Shear Data, Part 2 of 3
Line SpanID Location FBotCombo FBotMomen FBotArea
t
kN-m mm2
53 Span 1 Start Ult 8.0983 42.695
53 Span 1 Middle Ult 84.8400 464.653
53 Span 1 End Ult 62.9667 336.822
56 Span 1 Start Ult 19.7055 94.736
56 Span 1 Middle Ult 37.7405 195.337
57 Span 1 Middle Ult 29.1662 149.279
57 Span 1 End Ult 3.2324 11.732
B2 Span 1 Start Ult 4.1495 18.161
B2 Span 1 Middle Ult 6.7408 28.748
B5 Span 1 Start Ult 1.7196 0.000
B5 Span 1 Middle Ult 1.6755 0.000
B7 Span 1 Middle Ult 13.3579 96.590
B7 Span 1 End Ult 16.3300 132.548
B9 Span 1 End Ult 4.5164 29.079
B12 Span 1 Start Ult 0.8055 0.000
B15 Span 1 Start Ult 3.3059 5.690
B15 Span 1 Middle Ult 8.3416 31.359
B16 Span 1 Middle Ult 9.6858 58.762
B18 Span 1 Start Ult 0.4219 0.000
B20 Span 1 Middle Ult 24.3152 126.461
B21 Span 1 Middle Ult 49.3966 260.370
B22 Span 1 Middle Ult 34.8572 183.888
B22 Span 1 End Ult 27.7677 146.170
B23 Span 1 Middle Ult 14.3067 76.351
B23 Span 1 End Ult 0.0282 0.000

Page 43 of 50
 05 September 2019

BS 8110-1997 Concrete Beam Design

Geometric Properties

Combination = Overall Envelope

Beam Label = B6
Section Property = B 0.6*0.25
Length = 2.90158 m
Section Width = 250 mm
Section Depth = 600 mm
Distance to Top Rebar Center = 61 mm
Distance to Bot Rebar Center = 61 mm

Material Properties

Concrete Comp. Strength = 25 N/mm2

Concrete Modulus = 24855.58 N/mm2
Longitudinal Rebar Yield = 460 N/mm2
Shear Rebar Yield = 250 N/mm2

Page 44 of 50
Omer Abd Elaziz 4TH F.C.S BY SAFE.fdb SAFE 2016 v16.0.2 - License #*1J4YHDKN6Z68UAD
05 September 2017

Page 45 of 50
Omer Abd Elaziz 4TH F.C.S BY SAFE.fdb SAFE 2016 v16.0.2 - License #*1J4YHDKN6Z68UAD
05 September 2017

SLABS DESIGN - DEFLECTION CHECK (BS 8110-1:1997)

Materials : fcu = 25 N/sqmm fy = 460 N/sqmm

Span = 6 m Cover = 25 mm
Bar size(Bottom) = 12 mm Abar = 113 sq.mm
Slab thickness = 230 mm dav = 193 mm
Column width : b = 0.25 m

Design for bending moment :

M= 43 kN.m/m
K= 0.046 K=M/bd^2fcu
z/d = 0.95 z/d =0.5+s qrt(0.25-k/0.9)
z= 182.53 mm 0.775 ≤ z/d ≤ 0.95
As = 539.08 sq.mm/m As = M /(0.95*fy*z)
Asmin = 299 sq.mm/m Asmin=0.13*b*h/100 for fy=460N/sqmm
Asreg = 540 sq.mm/m Asmin=0.24*b*h/100 for fy=250N/sqmm
S(max) = 209 mm s max= (Ab/As reg)*1000
Spacing = 200 mm Select spacing ≤ Sm ax
Asprov = 565 sq.mm/m As prov=(Ab/s )*1000

Deflection calculations :

Service stress : fs = 293.10

M/bd^2 = 1.15
mf 1 = 1.30
(L/d)limit L/d = 30.33
(L/d)actual Ln /d = 29.79
OK

Page 46 of 50
Omer Abd Elaziz 4TH F.C.S BY SAFE.fdb SAFE 2016 v16.0.2 - License #*1J4YHDKN6Z68UAD
05 September 2017

6.5. Punching check/design

Table 34: Concrete Slab Design 02 - Punching Shear Data, Part 2 of 3
Table 34: Concrete Slab Design 02 - Punching Shear Data, Part 2 of 3
Point Combo Vu Gamma_v2 Gamma_v3 ShrStrMax Mu2 ShrStrCap
kN N/mm2 kN-m N/mm2
9 Ult 228.464 0.358072 0.443446 0.437124 9.1108 0.405026
11 Ult 281.433 0.358072 0.443446 0.520535 -21.7697 0.405026
13 Ult 257.926 0.358072 0.443446 0.378497 56.3358 0.405026
19 Ult 125.354 0.315677 0.490696 0.483054 -63.4352 0.405026
21 Ult 413.093 0.358072 0.443446 0.654214 17.0507 0.405026
51 Ult 284.537 0.358072 0.443446 0.399808 26.2463 0.405026

BS 8110-1997 Punching Shear Check & Design

Geometric Properties

Combination = Ult
Point Label = 21
Column Shape = Rectangular
Column Location = Interior
Global X-Coordinate = 13.86148 m
Global Y-Coordinate = 16.54123 m

Column Punching Check

Avg. Eff. Slab Thickness = 189 mm

Eff. Punching Perimeter = 3968 mm
Cover = 41 mm
Conc. Comp. Strength = 25 N/mm2
Reinforcement Ratio = 0.0000
Section Width x-22 = 1167 mm
Section Width x-33 = 817 mm
Gamma_v2 = 0.358072 Column Punching Perimeter
Gamma_v3 = 0.443446
Moment Mu2 = 17.0507 kN-m
Moment Mu3= -95.2344 kN-m
Shear Force = 413.093 kN
Unbalanced Moment Mu2 = 6.1054 kN-m
Unbalanced Moment Mu3= -42.2313 kN-m

Page 47 of 50
 Sep 2019

Punching Shear Check (BS8110-1:1997)

Input

fcu = 25 N/mm2
fy = 460 N/mm2
Slab Thickness = 230 mm
Bar Size = 16 mm Spacing = 150 mm
Cover = 25 mm
dav = 189 mm Asprov = 1339.7 mm2

Out put

1- at the column face :

0.8 (fcu)^0.5 = 4.0

0.8 (fcu)^0.5 vs 5 = 4.0

1- at 1.5d from the column face :

(100As/bv*d) = 0.708854 Should not be taken as greater than 3

(400/d)^(0.25) = 1.206145 Should not be taken as less than 0.67
(fcu/25) = 1 Should not be taken as less than 1

Vc = 0.679676 N/mm2

1 Page 48 of 50
 Sep 2019

Foundations Design
TABLE: Design Reactions B.C= 170
Story Joint Load Case FZ Area L req L final Depth Rein. F Type NO.
Label /Combo kN m2 m m m
Base 183 service 2233.51 14.98 3.87 4 0.8 T16@150 mm F1 1
Base 185 service 1973.29 12.94 3.598
Base 182 service 1944.39 12.90 3.59 3.6 0.7 T16@150 mm F2 3
Base 26 service 1875.17 12.24 3.50
Base 23 service 1721.58 11.27 3.36
Base 189 service 1704.43 11.13 3.34
Base 33 service 1654.94 10.81 3.29
3.4 0.7 T16@175 mm F3 6
Base 186 service 1599.83 10.45 3.23
Base 14 service 1586.23 10.36 3.22
Base 119.00 service 1575.48 10.28 3.21
Base 121 service 1562.37 10.20 3.19
Base 27 service 1535.28 10.11 3.18
Base 24 service 1466.30 9.66 3.11
3.2 0.7 T16@200 mm F4 6
Base 34 service 1440.88 9.49 3.08
Base 120 service 1408.51 9.28 3.05
Base 190 service 1403.31 9.25 3.04
Base 188 service 1357.42 8.78 2.96
Base 35 service 1285.71 8.32 2.88
Base 36 service 1266.47 8.19 2.86 3 0.6 T16@200 mm F5 5
Base 197 service 1247.19 8.07 2.84
Base 177 service 1215.31 7.86 2.80
Base 178 service 713.80 4.54 2.13
Base 187 service 649.96 4.13 2.03 2.2 0.5 T16@250 mm F6 3
Base 191 service 549.35 3.49 1.87

Combined footings:
Story Joint Load Case FZ Area L req L final Depth Rein. F Type NO.
Label /Combo kN m2 m m m
Base 26 service 1875.17
20.70 6.47 6.70 0.60 T16@100 B & T16@200T
Base 36 service 1266.47
C.F1 2
Base 186 service 1599.83
18.55 5.80 6.70 0.60 T16@100 B & T16@200T
Base 177 service 1215.31

RAFT:
Depth Rein.
T16@100 B
See Details 0.60
& T16@200 T

1 Page 49 of 50
 Sep 2019

Foundation F1 Design:
MATERIALS fcu 25 N/mm² h agg 20 mm gc 1.5 concrete
fy 460 N/mm² cover 50 mm gs 1.05 steel
Densities - Concrete 24 kN/m³ Soil 0 kN/m³ steel class B
Bearing pressure 170 kN/m² (net allowable increase)

DIMENSIONS mm
BASE COLUMN
L = 4000 h = 800
B = 4000 b = 300
depth H = 800
ex = 0 ey = 0

COLUMN REACTIONS kN, kNm characteristic Plot (to scale) Key

DEAD IMPOSED WIND
Axial (kN) 2087.2 244.0 STATUS VALID DESIGN
Mx (kNm)
Grnd Brg Pressure 97%
My (kNm)
Hx (kN) Bending fsx 97%
Hy (kN)
(As/Asprov) fsy 81%

Overturning FOS = Large Shear v xx 42%

Uplift FOS = infinite
v yy 54%

BEARING PRESSURES kN/m² characteristic punching 93%

CORNER 1 2 3 4
0% 25% 50% 75% 100% 125%
no wind 164.9 164.9 164.9 164.9
with wind 164.9 164.9 164.9 164.9 Efficiency

REINFORCEMENT Detail to 3.11.3.2 .

Mxx = 1060.0 kNm Myy = 1417.1 kNm
b = 4000 mm b = 4000 mm
d = 742 mm d = 726 mm
As = 3432 mm² As = 4690 mm²
PROVIDE 21 X16 @ 175 & 200 B1 PROVIDE 24 X16 @ 175 B2
As prov = 4222 mm² As prov = 4825 mm²
. .
BEAM SHEAR . .
Vxx = 710.5 kN at d from col face Vyy = 930.8 kN at d from col face
v = 0.239 N/mm² v= 0.321 N/mm²
or Vxx = 96.1 kN at 2d from col face or Vyy = 329.6 kN at 2d from col face
v = 0.032 N/mm² v= 0.113 N/mm²
vc = 0.283 N/mm² vc = 0.299 N/mm²

PUNCHING SHEAR . .
d ave = 734 mm u crit = 11008 mm
As prov = 0.154 % v max = 2.287 N/mm² at col face
v = 0.271 N/mm² vc = 0.291 N/mm²

1 Page 50 of 50