0% found this document useful (0 votes)
69 views15 pages

Configuracion Sw1: Practica 1 Ccna3

The document contains configuration steps for a Cisco switch named S1 including: - Configuring interfaces F0/1 and F0/3 as trunk ports to carry multiple VLANs - Configuring VLAN 10 and assigning port F0/6 to it - Creating VLAN 99 and assigning it an IP address of 192.168.99.1 to provide management access

Uploaded by

Ssebass Pozzo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
69 views15 pages

Configuracion Sw1: Practica 1 Ccna3

The document contains configuration steps for a Cisco switch named S1 including: - Configuring interfaces F0/1 and F0/3 as trunk ports to carry multiple VLANs - Configuring VLAN 10 and assigning port F0/6 to it - Creating VLAN 99 and assigning it an IP address of 192.168.99.1 to provide management access

Uploaded by

Ssebass Pozzo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 15

Practica 1

CCNA3

NOMBRE: ERICK POZO

CONFIGURACION SW1

--- System Configuration Dialog ---

Enable secret warning

----------------------------------

In order to access the device manager, an enable secret is required

If you enter the initial configuration dialog, you will be prompted for the enable secret

If you choose not to enter the intial configuration dialog, or if you exit setup without setting
the enable secret,

please set an enable secret using the following CLI in configuration mode-

enable secret 0 <cleartext password>

----------------------------------

Would you like to enter the initial configuration dialog? [yes/no]: no

Switch>en

*Mar 1 00:03:16.578: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively


down

Switch#

*Mar 1 00:07:15.117: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

*Mar 1 00:07:16.123: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,


changed state to up

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#
*Mar 1 00:07:53.151: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up

*Mar 1 00:07:54.157: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,


changed state to up

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#

Switch#conf ter

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#

*Mar 1 00:08:20.598: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,


changed state to down

*Mar 1 00:08:21.605: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down

Switch(config)#

Switch(config)#

Switch(config)#

Switch(config)#vtp domain CCNA

Changing VTP domain name from NULL to CCNA

Switch(config)#

*Mar 1 00:09:53.863: %SW_VLAN-6-VTP_DOMAIN_NAME_CHG: VTP domain name changed


to CCNA.

Switch(config)#vtp mode client

Setting device to VTP Client mode for VLANS.

Switch(config)#vtp pass

Switch(config)#vtp password cisco

Setting device VTP password to cisco

Switch(config)#

Switch(config)#
Switch(config)#

Switch(config)#

*Mar 1 00:10:34.346: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

*Mar 1 00:10:35.353: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,


changed state to up

Switch(config)#

Switch(config)#

Switch(config)#exit

Switch#vt

*Mar 1 00:11:15.685: %SYS-5-CONFIG_I: Configured from console by consolep

% Incomplete command.

Switch#

Switch#vtp st

Switch#show vtp st

Switch#show vtp status

VTP Version capable : 1 to 3

VTP version running :1

VTP Domain Name : CCNA

VTP Pruning Mode : Disabled

VTP Traps Generation : Disabled

Device ID : 6886.a789.5480

Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00

Feature VLAN:

--------------

VTP Operating Mode : Client

Maximum VLANs supported locally : 255

Number of existing VLANs :5

Configuration Revision :0

MD5 digest : 0x8B 0x58 0x3D 0x9D 0x64 0xBE 0xD5 0xF6
0x62 0xCB 0x4B 0x50 0xE5 0x9C 0x6F 0xF6

Switch#conf ter

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#hostn

Switch(config)#hostname S1_

S1_(config)#int f0/1

S1_(config-if)#sw

S1_(config-if)#switchport mode

S1_(config-if)#switchport mode tr

S1_(config-if)#switchport mode trunk

S1_(config-if)#

*Mar 1 00:15:43.902: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,


changed state to down

S1_(config-if)#

S1_(config-if)#

*Mar 1 00:15:46.914: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,


changed state to up

S1_(config-if)#

S1_(config-if)#no shu

S1_(config-if)#no shutdown

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#inter f0/3

S1_(config-if)#sw

S1_(config-if)#switchport mode tr

S1_(config-if)#switchport mode trunk

S1_(config-if)#

*Mar 1 00:16:17.583: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,


changed state to down

S1_(config-if)#

S1_(config-if)#
*Mar 1 00:16:20.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,
changed state to up

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#no shu

S1_(config-if)#no shutdown

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#exit

S1_#

S1_#

*Mar 1 00:16:35.476: %SYS-5-CONFIG_I: Configured from console by console

S1_#show inter

S1_#show interfaces f0/1 sw

S1_#show interfaces f0/1 switchport

Name: Fa0/1

Switchport: Enabled

Administrative Mode: trunk

Operational Mode: trunk

Administrative Trunking Encapsulation: dot1q

Operational Trunking Encapsulation: dot1q

Negotiation of Trunking: On

Access Mode VLAN: 1 (default)

Trunking Native Mode VLAN: 1 (default)

Administrative Native VLAN tagging: enabled

Voice VLAN: none

Administrative private-vlan host-association: none

Administrative private-vlan mapping: none


Administrative private-vlan trunk native VLAN: none

Administrative private-vlan trunk Native VLAN tagging: enabled

Administrative private-vlan trunk encapsulation: dot1q

Administrative private-vlan trunk normal VLANs: none

Administrative private-vlan trunk associations: none

Administrative private-vlan trunk mappings: none

Operational private-vlan: none

Trunking VLANs Enabled: ALL

Pruning VLANs Enabled: 2-1001

Capture Mode Disabled

Capture VLANs Allowed: ALL

Protected: false

Unknown unicast blocked: disabled

Unknown multicast blocked: disabled

Appliance trust: none

S1_#show interfaces f0/3 switchport

Name: Fa0/3

Switchport: Enabled

Administrative Mode: trunk

Operational Mode: trunk

Administrative Trunking Encapsulation: dot1q

Operational Trunking Encapsulation: dot1q

Negotiation of Trunking: On

Access Mode VLAN: 1 (default)

Trunking Native Mode VLAN: 1 (default)

Administrative Native VLAN tagging: enabled

Voice VLAN: none

Administrative private-vlan host-association: none

Administrative private-vlan mapping: none

Administrative private-vlan trunk native VLAN: none


Administrative private-vlan trunk Native VLAN tagging: enabled

Administrative private-vlan trunk encapsulation: dot1q

Administrative private-vlan trunk normal VLANs: none

Administrative private-vlan trunk associations: none

Administrative private-vlan trunk mappings: none

Operational private-vlan: none

Trunking VLANs Enabled: ALL

Pruning VLANs Enabled: 2-1001

Capture Mode Disabled

Capture VLANs Allowed: ALL

Protected: false

Unknown unicast blocked: disabled

Unknown multicast blocked: disabled

Appliance trust: none

S1_#conf ter

Enter configuration commands, one per line. End with CNTL/Z.

S1_(config)#inter f0/1

S1_(config-if)#sw

S1_(config-if)#switchport mode dy

S1_(config-if)#switchport mode dynamic de

S1_(config-if)#switchport mode dynamic desirable

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#show inter

S1_(config)#show interface trunk

% Invalid input detected at '^' marker.


S1_(config)#show interfaces trunk

% Invalid input detected at '^' marker.

S1_(config)#exit

S1_#show

*Mar 1 00:20:24.392: %SYS-5-CONFIG_I: Configured from console by co

S1_#

S1_#

S1_#

S1_#show inter trunk

Port Mode Encapsulation Status Native vlan

Fa0/1 desirable 802.1q trunking 1

Fa0/3 on 802.1q trunking 1

Port Vlans allowed on trunk

Fa0/1 1-4094

Fa0/3 1-4094

Port Vlans allowed and active in management domain

Fa0/1 1

Fa0/3 1

Port Vlans in spanning tree forwarding state and not pruned

Fa0/1 1

Fa0/3 1

S1_#conf ter

Enter configuration commands, one per line. End with CNTL/Z.

S1_(config)#vlan 10
VTP VLAN configuration not allowed when device is in CLIENT mode.

S1_(config)#exit

S1_#sho

*Mar 1 00:25:28.949: %SYS-5-CONFIG_I: Configured from console by consolew vlan brie

S1_#show vlan brief

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6

Fa0/7, Fa0/8, Fa0/9, Fa0/10

Fa0/11, Fa0/12, Fa0/13, Fa0/14

Fa0/15, Fa0/16, Fa0/17, Fa0/18

Fa0/19, Fa0/20, Fa0/21, Fa0/22

Fa0/23, Fa0/24, Gi0/1, Gi0/2

10 Rojo active

20 Azul active

30 Amarillo active

99 Administracion active

1002 fddi-default act/unsup

1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

S1_#conf ter

Enter configuration commands, one per line. End with CNTL/Z.

S1_(config)#int f0/6

S1_(config-if)#sw

S1_(config-if)#switchport mode acc

S1_(config-if)#switchport mode access

S1_(config-if)#sw

S1_(config-if)#switchport acc

S1_(config-if)#switchport access vlan 10


S1_(config-if)#exit

S1_(config)#inter

S1_(config)#interface vlan 99

S1_(config-if)#

*Mar 1 00:31:28.846: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan99, changed


state to up

S1_(config-if)#ip add

S1_(config-if)#ip address 192.168.99.1 255.255.255.0

S1_(config-if)#no shu

S1_(config-if)#no shutdown

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

*Mar 1 00:34:08.900: %LINK-3-UPDOWN: Interface FastEthernet0/6, changed state to up

*Mar 1 00:34:09.907: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6,


changed state to up

*Mar 1 00:42:06.053: %SYS-5-CONFIG_I: Configured from console by console

S1_>

S1_>

S1_>

S1_>

S1_>

S1_>

S1_>

S1_>en

S1_#conf ter

Enter configuration commands, one per line. End with CNTL/Z.


S1_(config)#int vlan 10

S1_(config-if)#

*Mar 1 00:43:33.613: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed


state to up

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#inter vlan 10

S1_(config-if)#sw

S1_(config-if)#ip add

S1_(config-if)#ip address 192.168.10.3 255.255.255.0

S1_(config-if)#no shu

S1_(config-if)#no shutdown

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#exti

% Invalid input detected at '^' marker.

S1_(config)#

S1_(config)#exit

S1_#p

*Mar 1 00:50:43.613: %SYS-5-CONFIG_I: Configured from console by consoleing

Protocol [ip]:

Target IP address:

% Bad IP address

S1_#ping 192.168.20.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.20.3, timeout is 2 seconds:


.....

Success rate is 0 percent (0/5)

S1_#

MODO TRANSPARENTE

S1_>en

S1_#conf ter

Enter configuration commands, one per line. End with CNTL/Z.

S1_(config)#int vlan 10

S1_(config-if)#

*Mar 1 00:43:33.613: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed


state to up

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#inter vlan 10

S1_(config-if)#sw

S1_(config-if)#ip add

S1_(config-if)#ip address 192.168.10.3 255.255.255.0

S1_(config-if)#no shu

S1_(config-if)#no shutdown

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#

S1_(config-if)#exit

S1_(config)#exti

% Invalid input detected at '^' marker.


S1_(config)#

S1_(config)#exit

S1_#p

*Mar 1 00:50:43.613: %SYS-5-CONFIG_I: Configured from console by consoleing

Protocol [ip]:

Target IP address:

% Bad IP address

S1_#ping 192.168.20.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.20.3, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

S1_#

CONFIGURACION SW3

Switch(config)#hostname S3

S3(config)#vtp mode client

Setting device to VTP Client mode for VLANS.

S3(config)#vtp domain CCNA

Changing VTP domain name from NULL to CCNA

S3(config)#

S3(config)#vtp password cisco

Setting device VTP password to cisco

S3(config)#end

S3#

S3(config-if)#switchport mode trunk

S3(config-if)#exit

S3(config)#int
S3(config)#interface fastEthernet 0/18

S3(config-if)#switchport mode access

S3(config-if)#switchport access vlan 10

S3(config)#interface vlan 99

S3(config-if)#ip address 192.168.99.3 255.255.255.0

S3(config-if)#exit

S3(config)#exit

S3#

S3#show

*Mar 1 00:28:14.440: %SYS-5-CONFIG_I: Configured from console by consolevla

S3#show vlan br

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6

Fa0/7, Fa0/8, Fa0/9, Fa0/10

Fa0/11, Fa0/12, Fa0/13, Fa0/14

Fa0/15, Fa0/16, Fa0/17, Fa0/19

Fa0/20, Fa0/21, Fa0/22, Fa0/23

Fa0/24, Gi0/1, Gi0/2

10 Rojo active Fa0/18

20 Azul active

30 Amarillo active

99 Administracion active

1002 fddi-default act/unsup

1003 token-ring-default act/unsup

1004 fddinet-default act/unsup

1005 trnet-default act/unsup

S3(config)#int vlan 99

S3(config-if)#no ip address
S3(config-if)#exi

S3(config)#ip default-gateway 192.168.10.254

S3(config)#int vlan 10

S3(config-if)#ip address 192.168.10.4 255.255.255.0

S3(config-if)#exit

You might also like