Oil-Free Range Operators Handbook

VT, VTS & VTH models

Covering Models:-

VT75 / VT150 / VT200 / VT250 / VT300 / VT400

VT75D / VT150D / VT200D / VT250D / VT300D / VT400D

VTS75 / VTS150 / VTS200 / VTS250

VTS75D / VTS150D / VTS200D / VTS250D

VTH75 / VTH150 / VTH200

VTH75D / VTH150D / VTH200D

BAMBI AIR COMPRESSORS LTD

152 Thimble Mill Lane

Heartlands
Birmingham
B7 5HT
Tel: 0121 322 2299
Fax: 0121 322 2297

Email: [email protected]
www.bambi-air.co.uk
Operating Manual

Your Bambi Air Compressor is a precision engineered product.

By following these simple steps you will ensure years of trouble free use.

Parts & Service are available from your Bambi dealer.

It is important to quote Model, Type & Serial Number in all communications.

The substitution of parts not manufactured nor approved by Bambi can impair
performance, service life and create potential mechanical or personnel hazards and
will invalidate your warranty.

Bambi reserves the right to modify the contents of this operating booklet without
notice and the information is in no way binding on the company.

Warranty
Provided the operating instructions have been followed, and the compressor has
been properly maintained, Bambi VT and VTS compressors are guaranteed against
faulty workmanship for a period of 2 years.
The air receiver is guaranteed for 5 years.
The guarantee does not cover damage by misuse, incorrect parts or service.
Contact Bambi Air Compressors or your retailer for further information.
 1

1) Safety Precautions 2) Siting The Compressor

What you must do: What you must do:
• Read these instructions before using • Provide adequate protection from the
your air compressor. weather.
• Ensure the compressor has been • Site the compressor level in both
installed, electrically connected planes.
and piped in by a properly qualified • Larger models are heavy. Ensure the
person. surface has sufficient load bearing
• Ensure the compressor is kept upright capacity.
at all times. • Allow access for maintenance all
around the compressor.
What you must not do: • Site in a dry area, avoiding damp or
• Do not attempt any maintenance on humid conditions. The site must be
the compressor until it has been dust free, well ventilated and have
isolated from the power supply. a cool ambient temperature. 40°C
• Do not attempt any work on the should be regarded as the maximum
compressor until the air receiver allowable ambient.
and pipe work systems are
depressurised. What you must not do:
• Compressed air is dangerous if • Enclose the compressor or allow
misused and can prove fatal. Avoid hot air generated by the motor to
any bodily contact with compressed air. re-circulate around the compressor.
• During operation the motor will Ensure there is 30cm clearance
become quite hot to the touch. around the compressor
Avoid contact to prevent burns. • Restrict air flow around the after
• Never tamper with the pressure relief cooler, after cooler fan unit or end
valve. cover ventilation [S models].
• Never lubricate the oil free motor or
pump assembly; this will cause Important ! For Silenced VTS Models:
severe damage. These compressors generate heat.
• Never obstruct cooling fans or outlet Never restrict any of the ventilation grilles
vents. otherwise serious damage may occur.

Electrical Connections
Where applicable, compressors are supplied with a moulded plug in accordance with
national standards.
Never remove the moulded plug.
The use of extension cables is not recommended as this may cause voltage drops which
can result in damage to the motor.

Note !
Duplex models VT300/300D, VT400/400D must be connected to a dedicated fused 20 amp supply.
Wired in accordance with European Standard –
Single phase: Blue = neutral, Brown = live, Yellow & Green Stripe = earth
Three phase: Brown/Black/Grey = Phase conductors
Blue = Neutral
Yellow and Green Stripe = earth
Three phase compressors should be connected by a competent person

All three phase units require neutral supply

2

3) Unpacking Instructions for:

VTS75 / VTS150 / VTS200/ VTS250
3.1) Fitting Mounting Castors
Before using the compressor you must remove the external packaging and fit the
castors supplied as they also provide essential clearance for the lower cooling fan
exhaust.

Note !
Failure to do so will cause damage and invalidate your warranty

Remove the four bolts securing the compressor to its wooden packing, carefully lift
the compressor to enable you to screw in the four castors using the same mounting
holes.

Take care lifting the compressor, some models are heavy.

3.2) Removing Internal Transit Packing

Before using the compressor you must remove the internal packing, failure to do so
will cause damage to the compressor. The procedure is as follows -
VTS75/150/200 VTS250D
Using the hex key provided, Using the hex key
remove the 3 bolts fixing the provided, remove the 4
left hand end cover in place bolts fixing the top cover
(when viewed from the front) in place and remove the
– see fig 1. top cover
- see fig 1a.
There are three packing
pieces, two either side of the There is one packing
pump unit, one on top of the piece on the top of the
cooling fan assembly. pump unit. Fig 1a.
Fig 1.
Ensure that these are Ensure that this is
removed. removed.
Reassembly is a reverse of the above but do not over-tighten the cover fixing bolts.

3.3) Fitting Condensate Bottle – VTS Dryer models only

Compressors fitted with an air dryer are supplied with a
condensate tank which you will need to fit before use.

Attach the condensate bottle mounting bracket to the front panel

of the compressor using the 2 plastic clips provided. These are
a simple push fit.

Slide the condensate bottle into the mounting bracket.

Fig.2 - VTS Condensate bottle position

Push the black plastic condensate tube which emerges from the front panel into the
hole in the lid of the bottle. As on Fig. 2

Fit the exhaust silencer to the condensate tube by pushing firmly on to the end of the tube.

Re-fit the bottle lid.

 3

4) Operation
Refer to exploded parts diagrams and illustrations when reading this section.

Note ! For VTS Models

Ensure the transit packing has been removed as described in the previous section.
Failure to do so will cause damage and invalidate your warranty
4.1) Starting & Stopping
Plug the compressor into an outlet socket of nominal voltage and fitted with the
correct fuse as shown in section Electrical Connections.

Switch the compressor on (I) using the on/off switch located on the front panel or
pressure switch - see fig 3 pictures:

Fig. 3 On off switch versions

The compressor will start running and automatically

switch off at the preset pressure.

Note!
Duplex Models VT300/300D, VT400/400D are fitted with a sequential start system to
reduce electrical loading. You will notice one motor starting a few seconds after the
other [single phase only]. This is normal.

As air is used the pressure drops and the motor will restart at the preset pressure.
Approx 2 Bar differential.

Note !
Each time the compressor switches off or the power supply is interrupted, you will
hear a short hiss of air. You are hearing the unloader valve discharging the residual
delivery pipe pressure. This is normal.

4.2) Adjusting Outlet Pressure

Use the pressure regulator to adjust the outlet pressure.

To increase line pressure, rotate the black knob next to the

pressure gauge in a clockwise manner, to decrease turn anti
clockwise. It is possible to lock the setting by pushing the knob
down until it “clicks” home – see fig 4.

Fig 4: Gauge layouts

On cabinet [VTS] models, gauges are labelled.

On others:
The smaller gauge is SELECTED pressure
The larger is RECEIVER pressure
4

5) Routine Maintenance
Refer to preventative maintenance section for frequency.

5.1) Draining the Air Receiver

Drain condensate from air receiver at a pressure of no more than 2 Bar.
Slowly open the red coloured drain tap
provided to allow water to flow out – see fig 5.

Fig. 5 Drain tap types

Close drain tap when all water has drained off.

Draining is not required on dryer equipped
models.
Automatic drains where fitted do not require draining, however the condensate tank
will require emptying – see following section “Operation Dryer Models”.

Note !
Waste condensate must be handled in accordance with national environmental rules.

5.2) Check Pressure Relief Valve

Ensure the air receiver is not pressurised.
On “S” models, refer to section 8: Removing
Housing Cover

Unscrew the knurled end of the pressure

relief valve until an audible “click” is heard.
Retighten without using excessive force.
Fig. 6 Pressure relief valve positions
6) Operation – Dryer Models
When equipped with an air dryer unit, the compressor will automatically dry the compressed
air before it is stored in the air receiver. This happens automatically and requires no additional
maintenance.This eliminates the need to manually drain the air receiver.

Operation is similar to standard versions with

the following change :-

Each time the compressor switches off or the

power supply is interrupted, the dryer purge
valve opens and automatically activates
the drain valve on the after cooler filter
allowing the dryer tower to regenerate. All
accumulated moisture will discharge into the
condensate tank.
This should be emptied when it reaches ¾ full.
Fig. 7 Condensate tank locations

Do not exceed the recommended 50% duty cycle, otherwise the dryer will not activate
and the humidity of the air will increase.
Ensure the after cooler fins are kept clear of accumulated dust.
 5

7) Technical
We recommend the compressor has a maximum 50% duty cycle to prolong pump life.

Note !
The motor must never be allowed to run continuously otherwise it will overheat and
may become damaged.

Do not ignore air leaks. All air connections must be leak free to prevent the
compressor from over heating.

The compressor is fitted with 2 thermal overloads. In the event of excessive

temperature the compressor will switch off and the external thermal protector will
activate. To re-set follow the procedure below-

Models: VT[H]75/75D, VT[H]150/150D, VT[H]200/200D, VT250/250D

Switch off at the pressure switch [see Fig. 2]. Allow 50 minutes for the motor to cool
down then switch back on at the pressure switch. The compressor will now restart.

Models: VTS75/75D, VTS150/150D, VTS200/200D, VTS250/250D

Do not switch the compressor off after overheating as this will prevent the internal
cooling fans which reduce the temperature inside the housing from running.

Allow 50 minutes for the motor to cool down.

Press the thermal re-set button, you will hear an audible click –
see fig 7.

The compressor will now restart.

Models: VT300/300D, VT400/400D

The re-set is integral with the pressure switch.
The pressure switch will automatically turn off (0) in the event of motor overload.
Turn the pressure switch to the on position [see Fig. 3].
The compressor will now restart.

If the compressor still does not run, switch off immediately and disconnect from the
mains supply.

You must find the cause of the overload and rectify this before continuing to use the
compressor.

Check for -
• Drain tap not closed properly
• Air leaks on the pneumatic fittings
• Compressor not the correct size for the work load
• Cooling fan outlets restricted

Contact your service engineer to investigate the cause.

6

8) Removing Housing Cover (VTS Models Only)

For routine maintenance it may be necessary to remove the top cover. Adhere to the
following procedure:
Models: VTS 75/75D, 150/150D, 200/200D
Disconnect from the mains power supply and release all the air from the compressor
and the air system.
Using the hex key provided, remove the 3 bolts fixing each end cover in place and
remove the end covers.
Remove the bolts holding the top cover in place.
Gently lift up the top housing.
Note !
Do not use excessive force as this will strain the electrical and air connections.
Carefully pull apart the electrical multi connector by squeezing the side clips and
gently pulling the connector apart. Do not use excessive force.
To release the air connections, push the connector collar in and simultaneously pull
the air tube out.
Reassembly is a reverse of the above but check that -
• The air tubes are pushed fully home into the connector and seal
• The electrical connector is secure
• No wires or air tubes are trapped in the housing join

Models: VTS250/250D
Disconnect from the mains power supply and release all the air from the compressor
and the air system
Using the hex key provided, remove the 4 bolts fixing the top cover in place and
remove the top cover.

Preventative Maintenance

Operation Daily Weekly Annually 2 Years

Drain Air Receiver •

Replace Air Intake Filter •

Check Pressure Relief Activation •

Clean After Cooler Fins •

Clean Ventilation Grilles •

Check Piston Ring •

Replace Air Dryer Filter •

Desiccant Change •

Coalescing Filter Element •

Above are to be considered minimum frequency

 7

Technical Specification

VT 0.75Hp Pump Specification

Motor kW / Hp 0.55 / 0.75

Voltage 220/240

Frequency Hz 50

Amps 3.9

Displacement l/min 120

VT 1.5Hp Pump Specification
Motor kW / Hp 1.1 / 1.5

Voltage [Single phase - 3 phase] 220/240 - 380/415

Frequency Hz 50

Amps [Single phase - 3 phase] 6.8 - 2.9

Displacement l/min 175

VT 2.0Hp Pump Specification
Motor kW / Hp 1.5 / 2.0

Voltage [Single phase - 3 phase] 220/240 - 380/415

Frequency Hz 50

Amps [Single phase - 3 phase] 9.9 - 3.6

Displacement l/min 220

VT 2.5Hp Pump Specification

Motor kW / Hp 1.84 / 2.5

Voltage [Single phase - 3 phase] 220/240 - 380/415

Frequency Hz 50

Amps [Single phase - 3 phase] 12.9 - 4.6

Displacement l/min 300

8
VT75
Ref No. Description Part no. 14 Red nylon drain tube BPB0284
1 Rubber foot BPB0601 15 50mm tank pressure gauge BPB0658
2 Inspection plug BPB0243 16 Pressure switch BPB0550
3 Inspection plug seal BPB0502 17 40mm line pressure gauge BPB0657
4 24 litre tank BPB0260 18 Pressure regulator BPB0510
5 40mm rubber mounting BPB0272 19 1/4 x 1/4 adaptor BPB1078
6 Motor mounting bracket BPB0321 20 1/4 on-off tap BPB1079
7 Solenoid c/w cable BPB0545 21 Safety valve BPB1084
8 1/8 x 6mm push fitting BPB0154 22 1/4 M/F elbow BPB1139
9 6mm black nylon tube BPB0203 23 3/8 adaptor BPB0283
10 Crankcase mounting bracket BPB0347 24 Delivery pipe BPB0508
11 20mm rubber mounting BPB0273 25 1/8 x 6mm elbow push fitting BPB0044
12 Drain valve tap BPB0281 26 3/8 Elbow BPB0282
13 3/8 x 10mm tube elbow BPB0277 27 Non-return valve BPB0656

7
8
17
9 13 14
12
15
10 16
6
11
5
19 18
20

21

23 22
5

24
4

3 26

2 9
1 25

27
 9
VTH75
Ref No. Description Part no.
1 Rubber foot BPB0601 13 3/8 x 10mm tube elbow BPB0276
2 Inspection plug BPB0243 14 Red nylon drain tube BPB0284
3 Inspection plug seal BPB0502 15 50mm tank pressure gauge BPB1081
4 24 litre tank BPB0473 16 Pressure switch BPB0550
5 Non-return valve BPB1086 17 40mm line pressure gauge BPB1077
6 1/4 Tee piece BPB0917 18 Pressure regulator BPB0510
7 Solenoid c/w cable BPB0545 19 1/4 x 1/4 adaptor BPB1078
8 1/8 6mm Tube elbow BPB0278 20 1/4 on-off tap BPB1079
9 1/4 x 1/8 Reducing bush BPB0041 21 Safety valve BPB1084
10 3/8 x 1/4 Reducing bush BPB0356 22 1/4 M/F elbow BPB1139
11 20mm rubber mounting BPB1200 23 1/4 Extension piece BPB0152
12 Drain valve tap BPB0895 24 Delivery pipe BPB0798

7
9
24
10
6
5

18
20
19
16
22
21

17
13
10 15
11 14
23

12
4

3
1
2
 10
VT75D
Ref No. Description Part no. 22 Red nylon drain tube BPB0284
1 Condensate diffuser BPB0588 23 3/8 x 10mm tube swivel elbow BPB0277
2 1/8 x 6mm push tube fitting BPB0154 24 3/8 adaptor BPB0283
3 Condensate bottle - complete BPB0088 25 50mm tank pressure gauge BPB0658
4 6mm nylon tube BPB0203 26 Pressure switch BPB0550
5 6mm tube divider BPB0279 27 1/4 On-off tap Closing ring BPB1079
6 1/8 x 6mm elbow tube fitting BPB0278 28 40mm line pressure gauge BPB0657
7 Solenoid valve c/w cable BPB0545 29 Pressure regulator BPB0510
8 Dryer assembly BPB0548 30 1/4 adaptor BPB1078
9 1/4 x 10mm push tube fitting BPB0591 31 Safety valve BPB1084
10 270mm Delivery pipe BPB0858 32 1/4 elbow BPB1139
11 3/8 elbow BPB0282 33 Non-return valve BPB0656
12 Coalescing filter BPB0258 34 3/8 x 10mm straight tube conn. BPB0275
12a Coalescing filter Auto-drain BPB0258B 35 Rubber foot BPB0601
13 Coalescing filter element BPB0655 36 Inspection plug BPB0243
14 3/8 elbow BPB0282 37 Inspection plug seal BPB0502
15 Aftercooler - complete BPB0560 38 24 litre tank BPB0260
16 Aftercooler mounting bracket BPB0557 39 1/4 x 10mm Tube swivel elbow BPB0276
17 40mm mounting rubber BPB0272 40 Dryer mounting clamp BPB0503
18 Motor mounting bracket BPB0321 41 Purge tank bleed pipe BPB0775
19 Crankcase mounting bracket BPB0347 42 Delivery pipe BPB0508
20 20mm mounting rubber BPB0273 43 Purge tank BPB0484
21 Drain valve tap BPB0281

28 29
15 27
25 26
14 16 30
24

11 20 31
19 23 32
18
17
21
10 42
22
32
41 40
8
33
43 34
39 38
10
37
40
10 36
35
10
9
12
13
6
7 4 5 4
4
12a 2
6 1
4 4
3
10 11
VTH75D
Ref No. Description Part no. 20 20mm mounting rubber BPB0273
1 Condensate diffuser BPB0588 21 1/4 Drain valve tap BPB0895
2 1/8 x 6mm push tube fitting BPB0154 22 Red nylon drain tube BPB0284
3 Condensate bottle - complete BPB0088 23 1/4 x 10mm Tube swivel elbow BPB0276
4 6mm nylon tube BPB0203 25 50mm tank pressure gauge BPB0658
5 6mm tube divider BPB0279 26 Pressure switch BPB1081
6 1/8 x 6mm Tube elbow BPB0278 27 1/4 On-off tap BPB1079
7 Solenoid valve c/w cable BPB0545 28 40mm line pressure gauge BPB1077
8 Dryer assembly BPB0548 29 Pressure regulator BPB0510
9 1/4 x 10mm push tube fitting BPB0591 30 1/4 adaptor BPB1078
10 10mm black nylon tube BPB0551 31 Safety valve BPB1084
12 Coalescing filter BPB0258 32 1/4 elbow BPB1139
12a Coalescing filter - auto drain BPB0258B 35 Rubber foot BPB0601
13 Coalescing filter element BPB0655 36 Inspection plug BPB0243
14 3/8 elbow BPB0282 37 Inspection plug seal BPB0502
15 Aftercooler - complete BPB1231 38 24 litre tank BPB0473
16 1/4 x 10mm Elbow BPB0820 40 Dryer mounting clamp BPB0503
17 Non Return Valve BPB1086 42 Delivery pipe BPB0508
18 1/4 Extension piece BPB0152 43 Purge tank BPB0484
18a 1/4 x 3/8 Reducing bush BPB0356 44 Delivery pipe BPB0858
19 Purge tank bleed valve BPB0775 45 Elbow BPB0044

16 10
23 29
10
17 26 30
14 32
15 31

27 28

23 22 18a 25
20 21 18

42
8
35
36 37 38 19
32
4
14
5
2
40 1 3
14
7 44
13
9
43 6
12 44
12a
45 4
12

VT150 / VT200
Ref No. Description Part no. 13a 3/8 x 10mm tube elbow [VT200] BPB0280
1 Rubber foot BPB0601 13b 3/8 x 10mm tube elbow [VT150] BPB0277
2 Inspection plug BPB0243 14 Drain tube BPB0284
3 Inspection plug seal BPB0502 15 50mm tank pressure gauge BPB0658
4 50 litre tank BPB0261 16 Pressure switch BPB0550
5 Rubber mounting [VT150] BPB1200 17 40mm line pressure gauge BPB0657
5a Rubber mounting [VT200] BPB0272 18 Pressure regulator BPB0510
6 Motor mounting bracket [VT150] BPB0321 19 1/4 adaptor BPB1078
6a Motor mounting bracket [VT200] BPB0516 20 On-off tap BPB1079
7 Solenoid valve c/w cable BPB0545 21 Safety valve BPB1084
8 1/8 x 6mm push fitting BPB0154 22 1/4 elbow BPB1139
9 6mm nylon tubing BPB0203 23 3/8 adaptor BPB0283
10 20mm mounting rubber [VT200] BPB0273 24 Delivery pipe BPB0508
11 Crankcase mounting bracket [VT200] BPB0517 25 1/8 x 6mm elbow tube fitting BPB0044
12 3/8 drain tap BPB0281 26 3/8 elbow BPB0282
27 Non-return valve BPB0656

7
8 17
9
18
13 14
10
15
6 / 6a 16
5 / 5a 11 12
19
20

23 21
22
5

24

26

9
25
3

2 27
1
 13
VTH150 / VTH200
Ref No. Description Part no.
1 Rubber foot BPB0601 13 1/4 x 10mm tube elbow BPB0276
2 Inspection plug BPB0243 14 Drain tube BPB0284
3 Inspection plug seal BPB0502 15 50mm tank pressure gauge BPB1081
4 50 litre tank BPB0474 16 Pressure switch BPB0550
5 Non return valve BPB1086 17 40mm line pressure gauge BPB1077
6 1/4 Tee BPB0917 18 Pressure regulator BPB0510
7 Solenoid valve c/w cable BPB0545 19 1/4 Adaptor BPB1078
8 1/8 x 6mm Tube elbow BPB0278 20 On-off tap BPB1079
9 1/4 x 1/8 Reducing bush BPB0041 21 Safety valve BPB1084
10 Rubber mounting BPB1200 22 1/4 Elbow BPB1139
11 3/8 x 1/4 Reducing bush BPB0356 23 1/4 Extension piece BPB0152
12 1/4 drain tap BPB0895 24 Delivery pipe BPB0798

7
9
24
11
6

18
20
19
16
22
21
17

10 15
14 11
13 23
4
12

3
2
 14

VT150D / VT200D
Ref No. Description Part no. 22 3/8 x 10mm Elbow [VT200D] BPB0280
1 Condensate diffuser BPB0588 22a 3/8 x 10mm Elbow [VT150D] BPB0277
2 1/8 x 6mm Push fitting BPB0154 23 3/8 M adaptor BPB0283
3 Condensate bottle complete BPB0088 24 50mm Tank pressure gauge BPB0658
4 6mm Nylon tube BPB0203 25 Pressure switch BPB0550
5 6mm Divider BPB0279 26 40mm Line pressure gauge BPB0657
6 1/8 x 6mm Elbow tube fitting BPB0278 27 Pressure regulator BPB0510
7 Solenoid valve c/w cable BPB0545 28 1/4 Adaptor BPB1078
8 Coalescing filter BPB0258 29 On/off tap BPB1079
8a Coalescing filter - automatic drain BPB0258B 30 Safety valve BPB1084
9 Coalescing filter element BPB0655 31 1/4 Elbow BPB1139
10 1/4 x 3/8 adaptor BPB0591 32 Non-return valve BPB0656
11 270mm Delivery pipe BPB0858 33 50 Litre tank BPB0261
12 3/8 x 10mm Swivel elbow BPB0282 34 3/8 x 10mm Connector BPB0275
14 Aftercooler BPB0561 35 Rubber foot BPB0601
15 Aftercooler bracket BPB0557 36 Inspection plug BPB0243
16 20mm Rubber mounting [VT150D] BPB1200 37 Inspection plug seal BPB0502
16a 40mm Rubber mounting [VT200D] BPB0272 38 1/4 x 10mm Swivel elbow BPB0276
17 Motor mounting bracket [VT150D] BPB0321 39 Dryer mounting bracket BPB0503
17a Motor mounting bracket [VT200D] BPB0516 40 Dryer assembly BPB0548
18 Crankcase mounting bracket [VT200D] BPB0517 41 Delivery pipe BPB0508
19 20mm Rubber mounting [VT200D] BPB0273 42 Purge tank bleed valve BPB0775
20 3/8 Drain tap BPB0281 43 Purge tank BPB0484
21 10mm Drain tube BPB0284
26
14 24 25 29
15
12 28 27
23

18 30
22
12 31
17 19
16
20
11 21
41
31 39
42
40
43
38

33
39
11 32

11 37 34
10 11
36
8 9 35
6
7 4 5 4
4
8a 2
6 1
4 4 3
 15
VTH150D / VTH200D
Ref No. Description Part no. 20 1/4 Drain tap BPB0895
1 Condensate diffuser BPB0588 21 Drain tube BPB0284
2 1/8 x 6mm Push fitting BPB0154 22 1/4 x 10mm Elbow BPB0276
3 Condensate bottle complete BPB0088 23 Elbow BPB0044
4 6mm Nylon tube BPB0203 24 50mm Tank pressure gauge BPB1081
5 6mm Divider BPB0279 25 Pressure switch BPB0550
6 1/8 x 6mm Elbow tube fitting BPB0278 26 40mm Line pressure gauge BPB1077
7 Solenoid valve c/w cable BPB0545 27 Pressure regulator BPB0510
8 Coalescing filter BPB0258 28 1/4 Adaptor BPB1078
8a Coalescing filter - auto drain BPB0258B 29 On/off tap BPB1079
9 Coalescing filter element BPB0655 30 Safety valve BPB1084
10 1/4 x 3/8 adaptor BPB0591 31 1/4 Elbow BPB1139
11 1/4 x 10mm Elbow BPB0820 32 50 Litre tank BPB0474
12 Black nylon tube BPB0551 33 Rubber foot BPB0601
13 3/8 Elbow BPB0282 34 Inspection plug BPB0243
14 Aftercooler BPB0869 35 Inspection plug seal BPB0502
15 Delivery pipe BPB0858 36 1/4 x 10mm Swivel elbow BPB0276
16 Non return valve BPB1086 37 Dryer mounting bracket BPB0503
17 Adaptor BPB0356 38 Dryer assembly BPB0548
18 Extension BPB0152 39 Delivery pipe BPB0508
19 20mm Rubber mounting BPB1200 40 Purge tank bleed valve BPB0775

31 41 Purge tank BPB0484

40
12
36 27
41
12 11
28
13 39 25
16 31
14 30
26
29
24
22 21 17
18
20

32

38 36

19

35 33
34 4
13
13 5 3
2 15
37 1
7 9
10
8
15
6
4

8a
4
23
16
VTS75 / 150 / 200
Ref No. Description Part no. 27 1/4 x 10mm Elbow BPB0276
1 On/Off switch APT626 28 Reducing bush BPB0255
2 Cabinet lid BPB0763 29 1/4 x 6mm Tube swivel elbow BPB0042
3 On/Off valve BPB1079 30 6mm tube Y connector BPB0279
4 1/4 10mm Stud elbow BPB0820 31 3/8 x 6mm Tube fitting BPB0756
5 1/4 10mm Tube elbow BPB0276 32 Drain tap BPB0281
6 1/4 Regulator BPB0510 33 1/4 x 6mm Elbow BPB0042
7 1/4 x 6mm Tube elbow BPB0758 34 Pressure switch BPB0550
8 1/4 Panel mounted gauge BPB0748 35 Safety valve BPB1084
9 Cooling fan housing inc. cover BPB0767 36 Cabinet tray BPB0764
10 1/4 x 6mm Elbow BPB0044 37 0.75 & 1.5HP crankcase bracket BPB0347
11 1/4 x 10mm Tube elbow BPB0276 37 2.0HP crankcase bracket BPB0517
12 Flanged inspection plug BPB0243 38 20mm rubber mount BPB0273
13 Inspection plug seal BPB0502 39 40mm rubber mount BPB0272
14 23ltr vessel BPB0795 40 M8 nyloc nut BPB0266
15 3/8 Plated elbow BPB0282 41 Motor mounting bracket 75 & 150 BPB0321
16 3/8 Non-return valve BPB0822 41a Motor mounting bracket 200 BPB0516
17 3/8 Tee BPB0802 42 Cutout / reset switch BPB0722
18 Delivery pipe BPB0798 43 Cooling fan BPB0727
19 3/8 x 1/8 Bush BPB0803 44 End panel BPB0538
20 Solenoid valve / cable assembly BPB0545 45 Cabinet base BPB0762
21 1/6 x 6mm Elbow BPB0278 46 Swivel castor BPB0811
22 Inspection plug seal BPB0502 47 1/8 x 6mm Tube fitting BPB0154
23 Hex screw BPB0265 48 Swivel castor with brake BPB0812
24 1/4 Tee BPB1109 49 1/8 Silencer BPB0588
25 M6 x 25 washer BPB0121 50 Thermal switch BPB0732
26 M8 nut BPB0161
 17

5
3 12
6
13
14
11 15
16
10 17
8 15
7
18 19
9
20 24
23
22 25
21 27
26
28
29
35
36 34 30
33

50
31
32
37
38 43
40
29 41/41a
42

39

29

47 44

46
45

46
49
48
18
VTS75D / 150D / 200D
Ref No. Description Part no. 29 3/8 Non-return valve BPB0822
1 On/off switch APT626 30 3/8 Plated elbow BPB0282
2 Cabinet lid BPB0763 31 Safety valve BPB1084
3 Delivery pipe BPB0728 32 Pressure switch BPB0550
4 3/8 Bulkhead connector BPB0749 33 Delivery pipe BPB0508
5 Coalescing filter BPB0258 34 1/4 Tee piece BPB1109
6 3/8 x 10mm Tube elbow BPB0277 35 1/4 x 6mm Tube fitting BPB0043
7 Coalescing filter element BPB0655 36 1/2 x 1/4 Flanged bush BPB1237
8 Coalescing filter - auto drain BPB0258B 37 M8 Hex full nut BPB0161
9 1/8 x 6mm Elbow BPB0044 38 M8 x 25 washer BPB0121
10 Dryer mounting clamp [two halves] BPB0503 39 M8 x 16mm set screw CP2737
11 1/4 x 10mm Tube elbow BPB0276 40 6mm Y connector BPB0279
12 Purge tank bleed pipe BPB0775 41 1/4 x 6mm Tube elbow BPB0042
13 1/4 Elbow BPB1139 42 Motor mounting bracket: 75/150 BPB0321
14 Dryer purge tank BPB0484 42a Motor mounting bracket: 200 BPB0516
15 1/4 x 10mm Elbow BPB0820 43 0.75/1.5HP Crankcase mtg bracket BPB0347
16 On/off valve BPB1079 43a 2HP Crankcase mounting bracket BPB0517
17 End panel BPB0538 44 20mm Rubber mount BPB0273
18 1/4 x 63mm 0-160 gauge BPB0748 45 40mm Rubber mount BPB0272
19 6mm tube elbow BPB0758 46 Cabinet base BPB0762
20 Regulator BPB0510 47 Cutout / Reset switch BPB0722
21 Solenoid valve / cable assembly BPB0545 48 Cooling fan BPB0727
22 1/8 x 6mm Tube fitting BPB0154 49 Swivel castor BPB0811
23 Aftercooler / fan assembly BPB0862 50 Water bottle c/w cap and cage BPB0088
24 Dryer assembly BPB0584 51 Drain valve BPB0281
25 Flanged inspection plug BPB0243 52 3/8 x 6mm Tube fitting BPB0756
26 Inspection plug seal BPB0502 53 Swivel castor with brake BPB0812
27 23ltr vessel BPB0795 54 Thermal switch BPB0732
28 3/8 x 10mm Tube connector BPB0275
 19

3 4
2 5

11 7
6
12 5
1 13
5
14
16 15 8
17 11 11 9
20 21
18 19 10

22
24
11
10 25
26
3 27 28
29

23 30
30
31
33
32
34
39
54 40 38
37 11
41
36 35
10
43/43a
44 37
42/42a
37
46 48

45 47
17
dP
i se
le rev
in
Tab o go
l ot
w xp 37
Ne

49
40
52
51

50 53
20
VT250
Ref No. Description Part no. 17 1/4 x 1/4 Adaptor BPB1078
1 M8 Hex full nut BPB0161 18 3/8 x 3/8 Adaptor BPB0283
2 Crankcase mounting bracket BPB0517 19 On/Off valve BPB1079
3 20mm Rubber mount BPB0273 20 Regulator BPB0510
4 M8 Flanged nut BPB0130 21 Pressure gauge BPB0657
5 2.0hp Motor mounting bracket BPB0516 22 Base plate BPB0319
6 40mm rubber mount BPB0272 23 Drain valve BPB0895
7 1/8 x 6mm push tube fitting BPB0154 24 Hose tail BPB1076
8 Delivery pipe BPB0798 25 1/4 Elbow BPB1139
9 3/8 Elbow BPB0282 26 Swivel castor with brake BPB0812
10 1/8 x 6mm elbow tube fitting BPB0044 27 Swivel castor BPB0811
11 3/8 X 3/8 N/R valve BPB0656 28 Flanged Inspection plug BPB0243
12 Pressure gauge BPB1081 29 Inspection plug seal BPB0502
13 3/8 Tee BPB0802 30 59 litre vessel BPB0230
14 Safety valve BPB1084 31 Motor Mtg bracket BPB0343
15 1/4 Elbow BPB1139 32 Solenoid valve / cable assembly BPB0545
16 Pressure switch BPB0550

5 1
2
3
4

1
7
6 8
32 9
31

10
30 11
13
12
29
28 15
14
1 17
16
21
27 18
22
19
25 20
26

24 23
 21
VT250D
Ref Description Part no.
No.
1 Delivery pipe BPB0858 1
2
2 3/8 Elbow BPB0614 3
3 Coalescing filter BPB0983 7 4
4 3/8 x 3/8 Adaptor CP0713 43 5
3
5 3/8 Elbow BPB0282 44 45
6
41 42
6 Delivery pipe BPB0357 3
7 Coalescing filter element BPB0655 17 7a
7a Coalescing filter auto drain BPB0983B 8
8 Solenoid valve / cable assembly BPB0545
9
9 1/8 x 6mm Tube elbow fitting BPB0278
10 Water bottle / black cap & cage BPB0088
10
11 Motor mounting bracket BPB0516
5 40
12 M8 Hex full nut BPB0161
13 Crankcase mounting bracket BPB0517
14 20mm rubber mount BPB0273 39
38
15 M8 Flanged nut BPB0130
12
16 40mm rubber mount BPB0272 11 13
17 Delivery pipe BPB0798 14
18 3/8 x 3/8 Non-return valve BPB0656
15
19 3/8 Tee BPB0802
15
20 Pressure gauge BPB1081 17
37 16
21 Safety valve BPB1084 18
22 1/4 Elbow BPB1139
36
23 Pressure gauge BPB0657
19
12 20
22
24 Pressure switch BPB0550
21
25 3/8 x 3/8 Adaptor BPB0283
23 46
26 On/Off valve BPB1079 24
35 34 33 28
27 Regulator BPB0510 25
28 Base plate BPB0315 27 26
29 Elbow BPB1139 29
30 Hose tail BPB1076 32
31 Drain valve BPB0895 30
31
32 Swivel castor with brake BPB0812
33 Inspection plug seal BPB0502
34 Inspection plug BPB0243
35 Swivel castor BPB0811
36 59ltr vessel BPB0230
37 Motor mounting bracket BPB0343
38 1/4 Elbow BPB1139
39 1/4 Extension piece BPB0150
40 Delivery pipe BPB0508
41 After-cooler c/w fittings and guard BPB0860
42 Safety valve BPB1084
43 After-cooler / dryer mounting brkt. BPB0330/0331
44 Twin tower dryer BPB0836
45 3/8 Outlet elbow BPB0629
46 1/4 x 1/4 Adaptor BPB1078
22
VTS250
Ref No. Description Part no. 25 1/8 x 6mm Elbow BPB0278
1 Top panel BPB0354 26 Delivery pipe BPB0508
2 3/8 x 10mm Tube elbow BPB0593 27 3/8 x 10mm Tube elbow BPB0277
3 3/8 Bulkhead connector BPB0749 28 3/8 Elbow BPB0282
4 Safety valve BPB1084 29 Non-return valve BPB0656
5 1/4 x 6mm Tube elbow BPB0042 30 Solenoid valve / cable assembly BPB0545
6 1/4 x 6mm Tube elbow BPB0758 31 After-cooler mounting bracket BPB0336
7 1/4 x 63mm 0-160 Gauge BPB0748 32 Cooling fan / housing: Large BPB0767
8 Pressure switch BPB0550 33 Cutout / Reset switch BPB0722
9 Cabinet: RH panel BPB0352 34 On/Off switch APT626
10 1/4 x10mm Tube elbow BPB0276 35 Drain valve BPB0895
11 Regulator BPB0510 36 Silencer BPB0588
12 Cabinet centre panel BPB0353 37 Cabinet base BPB0348
13 Cabinet back panel BPB0350 38 Retaining washer BPB0559
14 Cooling fan BPB0727 39 Spacer BPB0082
15 Fan guard BPB0355 40 M6 x 35mm caphead screw BPB0131
16 2.0HP Motor mounting bracket BPB0516 41 Swivel castor BPB0973
17 1/8 x 6mm Push fitting BPB0154 42 Motor mounting plate BPB0343
18 On/Off valve BPB1079 43 Swivel castor c/w brake BPB0974
19 M8 Hex full nut BPB0161 44 59ltr vessel BPB0230
20 2.0HP Crankcase mounting brkt. BPB0517 45 Inspection plug seal BPB0502
21 20mm Rubber mount BPB0273 46 Inspection plug BPB0243
22 M8 Flanged nut BPB0130 47 Cabinet front panel BPB0349
23 40mm Rubber mount BPB0272 48 Thermal switch BPB0732
24 Cabinet LH panel BPB0351
 23

4
23 5 6 7

13 8
5
9 11
12 10
14 10

53
16 15 17
18
19
20
21 25
22 11
23 34
25 24 31 32 33 35
26 30 36

27 28 29

19
41
44 39 38 37
40
45 42 47
46 43

5
24
VTS250D
Ref No. Description Part no. 29 3/8 Bulkhead connector BPB0749
1 Top panel BPB0354 30 3/8 Elbow BPB0629
2 Cooling fan BPB0727 31 Twin tower dryer BPB0836
3 Back panel BPB0350 32 Relief valve: 10bar BPB1084
4 Cabinet RH panel BPB0352 33 Extension piece BPB0150
5 Cabinet centre panel BPB0353 34 59ltr vessel BPB0230
6 1/4 x 6mm Tube elbow BPB0758 35 1/4 x 6mm Tube elbow BPB0042
7 1/4 x 63mm 0-160 gauge BPB0748 36 Inspection plug seal BPB0502
8 1/4 x 10mm Tube elbow BPB0276 37 Flanged inspection plug BPB0243
9 Regulator BPB0510 38 Non-return valve BPB0656
10 1/4 x10mm Elbow BPB0820 39 3/8 x 10mm Tube elbow BPB0593
11 On/Off valve BPB1079 40 Motor mounting plate BPB0343
12 Drain valve BPB0895 41 Cabinet LH panel BPB0351
13 On/Off switch APT626 42 Swivel castor BPB0973
14 Cutout/Reset switch BPB0722 43 Swivel castor c/w brake BPB0974
15 Water bottle c/w cap and cage BPB0088 44 M6 x 35mm cap head bolt BPB0131
16 Safety valve BPB1084 45 Spacer BPB0082
17 3/8 Bulkhead connector BPB0749 46 Retaining washer BPB0559
18 3/8 x 10mm Tube elbow BPB0593 47 Cabinet base BPB0348
19 Pressure switch BPB0550 48 M8 Hex nut BPB0161
20 Aftercooler c/w fittings / guard BPB0869 49 Cabinet front panel BPB0349
21 3/8 x Plated elbow BPB0282 50 After-cooler mounting bracket BPB0336
22 Delivery pipe BPB0728 51 M8 Flanged nut BPB0130
23 Delivery pipe BPB0798 52 20mm Rubber mount BPB0273
24 1/8 x 6mm Elbow BPB0278 53 2.0HP Crankcase mounting bracket BPB0517
25 Solenoid valve / cable assembly BPB0545 54 40mm Rubber mount BPB0272
26 Coalescing filter BPB0983 55 2.0HP motor mounting bracket BPB0516
26a Coalescing filter auto drain BPB0983 56 Fan guard BPB0355
27 Coalescing filter element BPB0655 57 Thermal switch BPB0732
28 Delivery pipe BPB0508
 25

6 7
1

4
2 3
5
9
8 8

57
10
56
11
55

48 9
53 12
52
51 48 41 13
54 14
50
39 40
38

48
21 42 47
46
49 15
44 45
43 17 16 8
18
29
34 25
22 20
26
37 36 29 21
28
25 8 19
30
35 31 27
26
32 23 23
21
26
26a
22
25

24
33

21
26

VT300 / VT400
Ref No. Description Part no. 15 Drain valve BPB0281
1 Inspection plug seal BPB0502 16 Solenoid c/w cable BPB0545
2 Inspection plug BPB0243 17 1/8 x 6mm Push fitting BPB0154
3 100 Litre tank BPB0262 18 Crankcase mounting bracket [VT300] BPB0347
4 Rubber foot BPB0601 18a Crankcase mounting bracket [VT400] BPB0517
5 3/8 Adaptor BPB0283 19 20mm Rubber mounting BPB0273
6 Safety valve BPB1084 20 40mm Rubber mounting BPB0272
7 Tank pressure gauge BPB0658 21 Motor mounting bracket [VT300] BPB0321
8 Pressure switch BPB0549 21a Motor mounting bracket [VT400] BPB0516
9 3/8 On/off tap BPB0535 22 Electrics enclosure BPB0513
10 Regulator BPB0511 23 Sequential timer BPB0512
11 Line pressure gauge BPB0657 24 6mm Nylon tube BPB0203
12 3/8 Elbow BPB0282 25 1/8 x 6mm Elbow push fitting BPB0044
13 Drain tube BPB0199 26 Delivery hose BPB0508
14 3/8 x 1/4 Hose tail BPB0652 27 Non return valve BPB0656

26

25 24
16
24 21/21a 18 17
18a
27
25
23
20

21/21a 19 2
26 27 1
20 22
18 20 15
18a
14
19
17 13

16 13

12

11
1
7
6

3 10
2 9
8
5
5
4
 27
VT300D / VT400D 25 Coalescing filter BPB0258
Ref No. Description Part no. 25a Coalescing filter - auto drain BPB0258B
1 Aftercooler mounting bracket LH BPB0863 26 Coalescing filter element BPB0655
1a Aftercooler mounting bracket RH BPB0557 27 1/4 x 3/8 Adaptor BPB0591
2 Inspection plug BPB0243 28 Dryer mounting clamp BPB0503
3 Inspection plug seal BPB0502 29 Purge tank BPB0484
4 Rubber foot BPB0601 30 Purge tank bleed pipe BPB0775
5 3/8 Adaptor BPB0283 31 Dryer assembly BPB0548
6 1/4 Elbow BPB1139 32 1/4 x 10mm Swivel elbow BPB0276
7 Safety valve BPB1084 33 Solenoid valve c/w cable BPB0545
8 50mm Tank pressure gauge BPB0658 34 3/8 x 10mm Connector BPB0275
9 Pressure switch BPB0549 35 Non return valve BPB0656
10 3/8 on/off tap BPB0535 36 1/8 x 6mm Push fitting BPB0154
11 Pressure regulator BPB0551 37 Condensate diffuser BPB0588
12 40mm Line pressure gauge BPB0657 38 Condensate bottle BPB0587
13 3/8 Elbow BPB0282 39 Motor mounting bracket [VT300D] BPB0321
14 3/8 x 1/4 Hose tail BPB0652 39 Motor mounting bracket [VT400D] BPB0516
15 Drain tube BPB0199 40 40mm Rubber mounting BPB0272
16 Drain tube clamp BPB0200 41 Crankcase mounting bracket [VT300D] BPB0347
17 Drain valve BPB0281 41 Crankcase mounting bracket [VT400D] BPB0517
18 10mm tube BPB0551 42 20mm Rubber mounting BPB0273
19 Aftercooler R/H BPB0561 43 Electrics enclosure BPB0513
20 3/8 x 10mm Swivel elbow BPB0593 44 Sequential timer BPB0512
21 Delivery tube BPB0508 45 100 Litre tank BPB0262
22 6mm Nylon tube BPB0203 46 Aftercooler L/H BPB0860
23 6mm Tube divider BPB0279 47 270mm Delivery pipe BPB0858
24 1/8 x 6mm Elbow BPB0278
32 31 6
21 31 30
6
30 18 29
32 28
13 29
28 18 27
13 46
33 24 47
47 25
33 26
22 25
27 24
47 25 22
26 25
25 25a
25 24
25a 23 22
22 13
24 19
22 22 23 22
13
23 36
37 21
18 47
34 38 39
40
35 41
18 34 35
44
1a
39 2
3
40 43 42 17
1 16
41 42
16 14
45
15
14
8 13
3 12
2 7 11
6
9 10
4 5
5
28
Motor / Pump Parts:
VT[H]75 / VT[H]75D / VT[H]150 / VT[H]150D / VT300/VT300D
Ref No. Description Part no. 21 Cylinder head BPB0681
1a Motor VT75 BPB0663 22 Intake filter BPB0682
1b Motor VT150 BPB0664 23 Cylinder head gasket BPB0620
2a 3/8 Elbow BPB0614 24 Valve plate nut BPB0683
2b 3/8 Elbow BPB0654 25 Valve plate washer BPB0684
3 Block fixing BPB0665 26 Outlet valve strip BPB0685
4 Block motor side BPB0666 27 Valve plate BPB0686
5 Block screw BPB0667 28 Inlet valve strip BPB0685
6 Block bearing BPB0668 29 Valve strip bolt BPB0687
7 Short spacer BPB0669 30 Valve plate gasket BPB0621
8 Con rod BPB0670 31 Cylinder bolt BPB0688
9 Con rod bearing BPB0671 32a Cylinder VT75 BPB0689
10 Eccentric BPB0672 32b Cylinder VT150 BPB0690
11 Large spacer BPB0673 33 Cylinder “O” ring BPB0691
12 Block “O” ring BPB0674 34 Top washer bolt BPB0692
13 Block fan side BPB0675 35 Top washer BPB0693
14 Stud bolt BPB0676 36 Piston seal BPB0623
15 16mm washer BPB0677 37a Capacitor VT75 BPB0695
16 M16 Nut BPB0678 37b Capacitor VT150 BPB0696
17 Fan BPB0625 38 Motor fan cover BPB0618
18 M16 Fan nut BPB0679
19 Fan cowling BPB0626
20 Cylinder head bolt BPB0680

20

21
26
37a / 37b 23 22
25
38
29 24
27
31
28
30
2
33
32a/32b
34
67 35
36
1a / 1b
3
12 13
5
4 8
9
10
11 7 19
16
17

18
14 6 15
 29
Motor / Pump Parts:
VT[H]200 / VT[H]200D / VT400 / VT400D
Ref No. Description Part no. 21 Fan ring BPB0705
1 Motor VT200 BPB0697 22 Fan cover fixing BPB0706
2a Elbow BPB0614 23 Cylinder head bolt BPB0680
2b 3/8BSP M/M Equal adaptor BPB0654 24 Cylinder head BPB0681
3 Block fixing BPB0665 25 Intake filter BPB0682
4 VT200 Block motor side BPB0699 26 Cylinder head gasket BPB0620
5 Block screw BPB0667 27 Valve plate nut BPB0683
6 Block bearing BPB0668 28 Valve plate washer BPB0684
7 Short spacer BPB0669 29 Outlet valve strip BPB0685
8 VT200 Con rod BPB0700 30 Valve plate BPB0686
9 Con rod bearing BPB0671 31 Inlet valve strip BPB0685
10 Eccentric BPB0672 32 Valve strip bolt BPB0687
11 Large spacer BPB0673 33 Valve plate gasket BPB0707
12 VT200 Capacitor BPB0701 34 Cylinder bolt BPB0688
13 Block “O” ring BPB0674 35 Cylinder VT200 BPB0708
14 VT200 Block fan side BPB0702 36 Cylinder “O” ring BPB0691
15 Stud bolt BPB0676 37 Top washer bolt BPB0692
16 16mm washer BPB0677 38 Top washer BPB0709
17 M16 Nut BPB0678 39 Piston seal BPB0710
18 Inner fan cover BPB0703 40 Outer fan cover BPB0716
19 Fan BPB0704 41 Motor fan cover BPB0619
20 M16 Fan nut BPB0679

23

24
41 12 25
26
28
29 27
30
34 32
31
33
2a 4
2b 36
35

37
1 67 38
39

3
13
5
8
9
10 11
22 7

20

14 15 6 17
18 16
19
21
40
30
Motor / Pump Parts:
VT250 / VT250D / VTS250 / VTS250D
Ref No. Description Part no. 23 VT250 Inner fan cover BPB0987
1 Motor VT250 BPB0995 24 Piston seal BPB0623
2a Outlet connector BPB0614 25 Top washer BPB0693
2b Outlet connector BPB0654 26 Top washer screw BPB0692
3 Block fixing BPB0665 27 Cylinder BPB0690
4 Block motor side BPB0666 28 Valve plate gasket BPB0621
5 Block screw BPB0667 29 Inlet valve strip BPB0685
6 Block bearing BPB0668 30 Outlet valve strip BPB0685
7 Short spacer BPB0669 31 Valve plate nut BPB0683
8 Con rod BPB0670 32 Cylinder head gasket BPB0620
9 Con rod bearing BPB0671 33 Inlet filter BPB0682
10 Eccentric BPB0672 34 Cylinder head BPB0681
11 Large spacer BPB0673 35 Cylinder head bolt BPB0680
12 Capacitor BPB0701 36 Valve plate washer BPB0684
13 Block O ring BPB0674 37 Valve plate BPB0686
14 Eccentric nut BPB0984 38 Valve plate bolt BPB0687
15 Block fan side BPB0675 39 Cyinder bolt BPB0688
16 Stud bolt BPB0676 40 Cylinder O ring BPB0691
17 Washer BPB0677 41 VT250 Left hand fan BPB0989
18 M16 nut BPB0678 42 90° connecting pipe BPB0993
19 VT250 Outer fan cover BPB0991 43 Straight pipe BPB0994
20 VT250 fan ring BPB0990 44 Tee piece BPB0992
21 Fan cover fixing BPB0706 45 Connecting pipe nut BPB0986
22 VT250 Right hand fan BPB0988 46 Connecting pipe olive BPB0985

12
35

34
2a 4 40 33
2b
27 32
36

26 29 31
1 37
6 25 38
7 24 30
28
41
39
3
13 15
5
8
9
10
11
7 14
17

42 43 16 6
21 17 18
45
19
44 23
22
20
46
 31
Wiring Diagrams - SINGLE PHASE

VT[H]75 / VT[H]150 / VT[H]200 / VT[H]75D / VT[H]150D / VT[H] 200D /

VT250 VT250D
DO NOT ALTER!!
1 KKEY: K
- Live
- Neutral
- Earth
VT300/400 5
1 - Supply
VT300D/400D 2 - Solenoid
3 - Earth
4 - Motor
5 - Pressure Switch
6 - Cooling fan
To electrics 7 - Timer box [VT250D only]
enclosure

VT300/400/300D/400D
[Electrics enclosure] Supply

A1 15

18 A2

DO NOT ALTER!!
Motor 1 Fan 1 Solenoid 1 Fan 2 Solenoid 2 Motor 2
 32
Wiring Diagrams - SINGLE PHASE - VTS
VTS75 150 200

2 3

Earth
to
11 case

8 7 6 5

9
10 4
12

1 - Thermal fan switch 4 - Thermal trip 10 - Compressor

2 - Pressure switch 5,6,7 & 8 Connection blocks 11 - Cooling fan KKEY: K
- Live
3 - Exhaust fan 9 - Solenoid 12 - Power in
- Neutral
- Earth

VTS75D 150D 200D

2 3 9

Earth
to
11 case

8 7 6 5

10 4
12

1 - Thermal fan switch 4 - Thermal trip 10 - Compressor

2 - Pressure switch 5,6,7 & 8 Connection blocks 11 - Cooling fan
3 - Exhaust fan 9 - Solenoid 12 - Power in
 33
Wiring Diagrams - SINGLE PHASE - VTS cont’d

VTS250 / 250D

Earth to case
1
Connector

4
2 8 7 6 5

12

13
3

10 11 9
3

1 - Power in 5,6,7 & 8 Connection blocks 12 - Thermal fan switch NOTE!

2 - Pressure switch 9 - Solenoid 13 - Timer box The cooling fans
3 - Cooling fans 10 - Motor Note! Timer box only used remain live even with
4 - Thermal trip 11 - Aftercooler fan on Dryer models the power switch in
the “OFF” position

KKEY: K
- Live
- Neutral
- Earth
 34
Wiring Diagrams - THREE PHASE
VT[H]150 / VT[H]200 / VT[H]150D / VT[H]200D
VT 250& VT250D

MOTOR

PRESSURE SWITCH
L1
SUPPLY
L2

L3

Connector
block

SOLENOID

KKEY: K AFTER COOLER FAN

- Live (Dryer models only)
- Neutral
- Earth

VT300/400/300D/400D

Overload set to 10 amps

DO NOT ALTER! Solenoid
1
PRESSURE SWITCH
Solenoid
L1
2
SUPPLY
L2 GREY BLUE EARTH BROWN BLACK
Fan 1

L3

Fan 2

NOTE:
Fans only used
on dryer models
N

MOTOR MOTOR
1 2
 35
SERVICE RECORD

Date installed____________________________

Date Maintenance work Signature / Company

SERVICE KITS
BPVT 1 Service Kit covers models:
VT75 / VT150 / VT250 (2 kits) VT300 (2 kits) – including H/D/S variants

BPVT2 Service Kit covers models:

VT200 and VT400 (2 kits) - including H/D/S variants

BPB0655 required to change the Coalescing Filter Element

 36

AIR DRYER PERFORMANCE

Where fitted, the air dryer unit was tested using a Michell
Instruments C2TX Hygrometer
The test procedure was carried out in accordance with ISO8573-1 Class
9.2.9:2010 Class 9.2.9

Molecular Sieve Type BS4A 2.5/5.00mm

Test Result: -40 Degree Dew Point

Duty Cycle Time: Full Flow @50%

Performance: [100% pass]

NOTE: To ensure the optimum performance of your Bambi dryer please

note that the desiccant and filter need to be changed every two years
or if the Dew Point level is no longer achieved due to degradation of the
desiccant in extreme working conditions.
 37

NOTES
 EC Declaration of Conformity - Declaration de Conformite CE –
EG Konformitatserklarung
Declaracion de Conformidad CE - EG Verklaring van Overeenstemming
Bambi Air Compressors declares that this product conforms to the European
Directives listed below.

Bambi Air Compressors declare que ce produit est conforme aux directives
europeennes enumerees ci-dessous.

Bambi Air Compressors declara que este producto cumple con la DirectivaEuropea
listada abajo.

Bambi Air Compressors verklaart dat dit product voldoet aan de

onderstaande Europese Richtlijnen

Bambi Air Compressors erklart hiermit, dass dieses Produkt mit den Bestimmungen
der Nachstehenden EU-Richtlinien ubereinstimmt.

Machinery Safety Standard 89/392 EC, Low Voltage Directive 2006/95 EC Machinery Directive
2006/42 EC, Electromagnetic Compatibility 2004/108 EC
Simple Pressure Vessels 2009/105/EC
EN60034, EN60204-1:2007, EN ISO12100-1-2:2005, EN ISO13857:2010
CE Marking applied for the first time in 1997

IF NO SERIAL NUMBER HERE

THEN HANDBOOK ISSUED AS
REPLACEMENT OR WITH SERVICE KIT

L. Clutterbuck
Director

Issue 5: 01/16