UNIT-III-Dielectric and Magnetic properties of materials

Syllabus:

Dielectric constant and polarization of dielectric materials - Types of polarization – Equation

for internal field in liquids and solids ( one dimensional) – Clausius Mosotti equation – Ferro
and Piezo electricity (qualitative) – Frequency dependence of dielectric constant- Important
applications of dielectric materials.

Classification of dia, para and ferromagnetic materials. Curie Temperature Hysterisis in

ferromagnetic materials. Soft and Hard magnetic materials. Applications.

Introduction
Dielectrics are insulating or non-conducting ceramic materials and are used in many
applications such as capacitors, memories, sensors and actuators. Dielectrics are insulating
materials that exhibit the property of electrical polarization, thereby they modify the dielectric
function of the vacuum. A dielectric material is any material that supports charge without
conducting it to a significant degree. In principle all insulators are dielectric, although the
capacity to support charge varies greatly between different insulators. Although these materials
do not conduct electrical current when an electric field is applied, they are not inert to the electric
field. The field may cause a slight shift in the balance of charge within the material to form an
electric dipole.

Thus the materials is called dielectric material.

Dielectric materials are used in many applications, from simple electrical insulation to sensors
and circuit components.

Faraday was carried out the first numerical measurements on the properties of insulating
materials when placed between the two parallel plates (capacitor), those materials, he called as
dielectrics. He has found that the capacity of a condenser was dependent on the nature of the
material separating the conducting surface. This discovery encouraged further empirical studies
of insulating materials aiming at maximizing the amount of charge that can be stored by a
capacitor. In search of suitable dielectric materials for specific applications, these materials have
become increasingly concerned with the detailed physical mechanism governing the behavior of
these materials.

The difference between dielectric material and insulator depends on its application.
Insulating materials are used to resist flow of current through it, on the other hand dielectric
materials are used to store electrical energy. In contrast to the insulation aspect, the dielectric
phenomena have become more general and fundamental, as it has the origin with the dielectric
polarization.
Electric dipoles:
Upon application of a dc or static electric field, there is a long range migration of charges.
However, there is a limited movement of charges leading to the formation of charge dipoles and
the material, in this state, is considered as polarized. These dipoles are aligned in the direction of
the applied field. The net effect is called Polarization of the material.

A dielectric supports charge by acquiring a polarisation in an electric field, whereby one surface
develops a net positive charge while the opposite surface develops a net negative charge. This is
made possible by the presence of electric dipoles – two opposite charges separated by a certain
distance – on a microscopic scale.

1. If two discrete charged particles of opposite charges are separated by a certain distance, a
dipole moment μ arises.

2. If the centre of positive charge within a given region and the centre of negative charge within
the same region are not in the same position, a dipole moment μ arises. For example, in the
diagram below the centre of positive charge from the 8 cations shown is at X, while the centre of
negative charge is located some distance away on the anion.

The second view of dipole moment is more useful, since it can be applied over a large area
containing many charges in order to find the net dipole moment of the material.

The dipoles can be aligned as well as be induced by the applied field.

Note that in the equation for dipole moment, r is a vector (the sign convention is that r points
from negative to positive charge) therefore the dipole moment μ is also a vector

Electric field intensity or electric field strength ( E )

The force experienced by a unit test charge is known as electric field strength E
Q
E …..(1)
4r 2
where  is the permittivity or dielectric constant of the medium in which electric charge is
placed. For vacuum  = o = 8.854 X10-12Fm-1

Electric flux density or electric displacement vector ( D)

The electric flux density or electric displacement vector is the number of flux lines
crossing normal to a unit surface area. The electric flux density at a distance from the point
charge Q is
Q
D  …..(2)
4r 2
then from (1) and (2) D = E ….. (3)

Dielectric constant (r)

The dielectric constant of a material is defined as the ratio of the permittivity of the
medium () to the permittivity of free space (o). It can also defined as the ratio of the
capacitance with dielectric (Cd) and with air ( CA) between the plates.
 Cd
r   …..(4)
 o CA
Capacitance: The property of a conductor or system of conductor that describes its ability
to store electric charge.

C=q/V=Aε/d where

C is capacitance of capacitor
q is charge on the capacitor plate
V is potential difference between plates
A is area of capacitor plate
ε is permittivity of medium
d is distance between capacitor plates

Units: Farad .
Polarization
When an electric field is applied to a material with dielectrics, the positive charges are
displaced opposite to the direction of the field and negative charges displaced in the direction of
the field. The displacement of these two charges create a local dipole, creation of dipole by
applying electric field is called as polarization.
 Polarization is defined as induced dipole moment per unit volume.

P …(5)
Volume
Polarisability
The polarization P is directly proportional to the electric field strength E
PE
…(6)
P  E
Where  proportionality is constant called as polarisability. The polarisability is defined as
polarization per unit applied electric field. If the material contains N number of dipoles per unit
volume then
P  NE ….(7)

Relation between polarization and dielectric constant

Let us apply Gauss theorem for parallel plate condenser.

q
 E0 dA  0
q
E0 A 
0
q 
E0   . …(1)
A 0  0
Where σ is the charge per unit area.

Let a dielectric slab placed between two plates. Due to polarization, charges appear on the two
faces of the slab, and establish yet another field within the dielectric media. Let this field be Eʹ.
The direction of Eʹ will be opposite to that of E0.

The resultant field E in the material can be written as,

E = E0- Eʹ ……………….(2)
If σp is the charge/unit area on the inserted dielectric slab surfaces, then by following equation
(1), we write,
q' p
E'   . …………………(3)
A 0  0
From (1), (2) and (3),
 p
` E  .
0 0
or
 0 E     p ……………………(4)

Since the magnitude of polarization P = dipole moment/ Unit Volume

But dipole moment = induced charge X distance
Therefore
P = induced charge/ Area=  p

We know that electric displacement fieldor electric flux density D is given by charge /unit area

D = q/A= 

Therefore Equation 4 becomes

0E  D  P

P  D  E 0 .….(5)
in free space where there is no dielectric P=0
D  E 0
But in dielectric media the D changes. From electrostatics
D   0 r E
From (3)

P  E o  r  E 0

P  E 0 ( r  1) ……………….(6)

 r  1  P

E 0
Where  is electric susceptibility of the dielectric medium. It doesn’t have any units.

Since P and E are vectors eqn (6) can be written as

  
P  E 0 ( r  1) …(7)
This equation represents polarization vector.

Types of polarization
Dielectric polarization is the displacement of charge particles with the applied electric
field. The displacement of electric charges results in formation of electric dipole moment in
atoms, ions or molecules of the material. There are four different types of polarization, they are
listed below.
1. Electric polarization,
2. Ionic polarization,
3. Orientation polarization
4. Space charge polarization

Electric polarization
The displacement of the positively charged nucleus and the negatively charged electrons
of an atom in opposite directions, on application of an electric field, result in electronic
polarization.

On applying a field, the electron cloud around the nucleus shifts towards the positive end of the
field. As the nucleus and electron cloud are separated by a distance, dipole moment is created
within each atom. The extent of this shift is proportional to the field strength.

Induced dipole moment

e  E

e   e E
Where  e is called electronic polarizability. The dipole moment per unit volume is called
electronic polarization.

 It increases with increase of volume of the atom.

 This kind of polarization is mostly exhibited in monoatomic gases.(e.g. He, Ne, Ar, Kr,
Xe etc..)
  It is independent of temperature.

 It occurs only at optical frequencies (1015Hz)

 Vast fast process: 10-15~10-16s.

Calculation of electronic polarizability:

Electronic polarization can be explained by classical model of an atom in gasses. In gases the
atoms are assumed that the interaction among the atoms is negligible. Here the nucleus of charge
Ze is surrounded by an electron cloud of charge –Ze distributed in the sphere of radius R.

Ze
Charge density,    …(1)
(4 / 3)R 3
When an electric field E is applied, the nucleus and electrons experience Lorentz force of
magnitude ZeE in opposite direction. Therefore the nucleus and electrons are pulled apart. As
they are pulled apart a Coulomb force develops between them. At equilibrium these two forces
are equal and nucleus and electron cloud are separated by a small distance x.

Lorentz force = ZeE …(2)

Ch arg eenclosed int hesphereofradiusx

Coulomb Force = Ze X
4 0 x 2

4 3
The charge enclosed = x 
3

4 3  3  Ze 
From equation (1) = x   3 
3  4  R 

Zex 3
= 
R3
 Ze Zex 3 Z 2e2 x
Hence Coulomb force is = X    …(3)
4 0 x 2 R3 4 0 R 3

At equilibrium Lorentz force = Coulomb force (equation (2) equal to (3))

Z 2e2 x
 ZeE  
4 0 R 3

4 0 R 3 E
x …(4)
Ze

The displacement of the electron cloud is proportional to applied electric field.

Ze4 0 R 3 E
The electric dipole moment  e  Zex 
Ze

 e  4 0 R 3 E
e  E

e   e E …(5)

Where  e  4 0 R 3 is called electronic polarizability.

Pe  N e  N e E

Where N is the number of atoms/m3

But polarization P  E 0 ( r  1)  N e E

N e ( r  1) 0
( r  1)  or  e 
0 N

Ionic Polarization
Ionic polarization occurs in ionic solids such as NaCl, KBr, and LiBr. When an
electric field is applied to an ionic solid the positive and negative ions displace to their respective
polarities creating an electric dipole this is called as ionic polarization.

In the absence of an electric

field there is no displacement of ions.
When an electric field is applied an induced
dipole moment i is produced.

Let x1 and x2 be the displacement of

positive and negative ion respectively.
Then the induced dipole moment.
  i  e( x1  x2 ) …(6)
Let F be restoring force F
 x1
 x2
  1 x1
  2 x2

From mechanics the spring constant of mass attached to a spring is given by  =m2

At equilibrium the Lorentz force = restoring force

eE  m02 x

eE eE eE
Therefore x Then x1  x2 
m 02 m 02 M 02

e2  1 1 
  2   E  i E …(7)
0  m M 

e2  1 1 
Where  i  2    is called as ionic polarisability …(8)
0  m M 

Orientation Polarization
Orientation polarization occurs only in polar molecules (the molecules which have
permanent dipole moment eg H2O, Phenol, etc.). When an electric field is applied to a polar
molecule, the dipoles experience a torque and try to align parallel to the applied field.

Consider a polar molecule subjected to an

electric field E. The alignment of electric dipole
with the electric field is similar to the alignment
of magnetic dipole with the applied magnetic
field in paramagnetic material.

The expression for polarization can be obtained

from the theory of paramagnetism.

The orientation polarization is given as

N o2 E
P0   o E …(9)
3KT
 o2
Where  0  is called as orientation polarisability …(10)
3KT

Space charge polarization

Space charge polarization occurs due to the
accumulation of charges at the electrodes or at
interfaces in a multiphase materials.

In the presence of an applied field, the mobile

positive ions and negative ions migrate toward the
negative electrode and positive electrode
respectively to an appreciable distance giving rise to
redistribution of charges , but they remain remains
in the dielectric material (electrode is blocking). The space charge polarization can be defined as
the redistribution of charges due to the applied electric field and the charges accumulate on the
surface of the electrodes. It occurs when the rate of charge accumulation is different from rate of
charge removal. Space charge polarization is not significant in most of the dielectric materials.

Internal field in liquids and solids (one dimensional)

In gases state the atoms are separated by large distances and the interaction between
the atoms can be neglected. When an external electric field E is applied, the intensity of the
electric field experienced by an atom in gases state will be equal to the applied electric field E.
In solids and liquids, the atoms are close to each other leading to strong interaction
between them. In solids and liquids the intensity of the electric field at a given point of the
material is not equal to the applied electric field but equal to internal field which is the sum of
applied electric field and field due to other dipoles present in the material.

Internal field Ei =E+E` …(1)

The internal field can be calculated by Epstein model in the case of one dimensional
atomic array.

Electric field along the axis of an electric dipole

Consider an electric dipole of length 2d and charge Q, the field along the axis of the
dipole at point A is the sum of the electric field due to +Q and –Q.

Q
The electric field due to +Q at point A is E  
4 o ( x  d ) 2

Q
The electric field due to +Q at point A is E  
4 o ( x  d ) 2

Q  1 1 
Electric field of dipole at A is E A  E   E     
4 o  ( x  d ) 2
(x  d )2 

2Q  2dx 
  2 
4 o  ( x  d ) ( x  d ) 
2
 since x >> d (x-d)2  (x+d)2  x2 then
2Q  2dx  4dQ
  4 

4 o  x  4 o x 3
2 i
since 2dQ =i E A …(2)
4 o x 3

Consider an array of one dimensional atoms along x- axis. The all the atoms are similar, equally
spaced and have induced electric dipole moment i in an applied electric field E. The electric
field experienced at the A is the sum of electric fields of other dipoles and applied electric field
E.

The electric
field at A due to
the induced dipole B and L which are at a distance x is
2 i
E B  EL 
4 o x 3
The electric field at A due to the induced dipole C and M which are at a distance 2x is
2 i
E C  EM 
4 o (2 x) 3
Therefore the field due to other dipoles is

E’ =EB + EL+EC+EM+ED+EN+…. …(3)

2 i 2 i 2 i 2 i 2 i 2 i
E        ...
4 o x 4 o x 4 o (2 x) 4 o (2 x) 4 o (3x) 4 o (3x)3
3 3 3 3 3

4 i 4 i 4 i
E     ...
4 o x 4 o (2 x) 4 o (3x)3
3 3

i  1 1 1 1  1 1 1 1
E  3 
1  3  3  3  3  ... where 1      ...  1.2
 o x  2 3 4 5  23 33 43 53

1.2i
E 
 o x 3

1.2i
Therefore the internal field Ei  E  …(4)
 o x 3
 The local field in a three dimensional solid is similar the above equation the number
density N of atoms replaces 1/a3. Since Nμi=P and 1.2/π is replaced by γ. Then the internal field
is

1.2 Ni 1.2 P P

Ei  E   E  E
 o  o o

γ depends on the internal structure For a cubic symmetry crystal γ value is1/3

P
Ei  E  …(5)
3 o

The field given by the above equation is called Lorentz field.

Clausius - Mosotti equation

Let us consider elemental solid dielectric which exhibits only electronic polarization. If
e is the electronic polarisability per atom, it is related to the bulk polarization P through the
relation

P  N e Ei …(6)

P
e  …(7)
NEi

Where N is the number of atoms per unit volume and Ei is the local field using the relation (5)
P
e  …(8)
 P 
N E  
 3 o 

By using the relation between the polarization and permittivity we have

P  E 0 ( r  1) …(9)

P
E …(10)
 0 ( r  1)

Substitute the value of E from (10) in (8)

P
e 
 P P 
N  
  0 ( r  1) 3 o 

N e 1 1
 
0  1 1  r  2 
    
 ( r  1) 3   3( r  1) 
  r  1 N e

 r  2 3 0 …(11)

The above equation is known as Clausius Mosotti equation which is valid for nonpolar solids

Dielectric loss:

Dielectric loss is the dissipation of energy through the movement of charges in an alternating
electromagnetic field as polarisation switches direction.

An efficient dielectric supports a varying charge with minimal dissipation of energy in the form
of heat is called dielectric loss. There are two main forms of loss that may dissipate energy
within a dielectric. In conduction loss, a flow of charge through the material causes energy
dissipation.

Dielectric loss is especially high around the relaxation or resonance frequencies of the
polarisation mechanisms as the polarisation lags behind the applied field, causing an interaction
between the field and the dielectric’s polarisation that results in heating. This is illustrated by the
diagram below (recall that the dielectric constant drops as each polarisation mechanism becomes
unable to keep up with the switching electric field.)

Dielectric loss quantifies a dielectric material's inherent dissipation of electromagnetic

energy into, e.g., heat.

It can be represented in terms loss tangent tan δ and is defined:

Dielectric Breakdown : The dielectric breakdown is the sudden change in state of a

dielectric material subjected to a very high electric field , under the influence of which , the
electrons are lifted into the conduction band causing a surge of current , and the ability of
the material to resist the current flow suffers a breakdown .

Or

When a dielectric material loses its resistivity and permits very large current to flow through it,
then the phenomenon is called dielectric breakdown

Or

At high electric fields, a material that is normally an electrical insulator may begin to conduct
electricity – i.e. it ceases to act as a dielectric. This phenomenon is known as dielectric
breakdown.
Frequency dependence of polarizability:
On application of an electric field, polarization process occurs as a function of time. The
polarization P(t) as a function of time. The polarization P(t) as a function of time t is given by

P(t) = P[ 1- exp ( - t / t r )]

Where P – max. Polarization attained on prolonged application of static

field. t r - relaxation time for particular polarization process

The relaxation time t r is a measure of the time scale of polarization process. It is the time
taken for a polarization process to reach 0.63 of the max. value.

Electronic polarization is extremely rapid. Even when the frequency of the applied
voltage is very high in the optical range (≈1015 Hz), electronic polarization occurs during
every cycle of the applied voltage.
Ionic polarization is due to displacement of ions over a small distance due to
the applied field. Since ions are heavier than electron cloud, the time taken for
displacement is larger. The frequency with which ions are displaced is of the same
order as the lattice vibration frequency (≈1013Hz). Hence, at optical frequencies,
there is no ionic polarization. If the frequency of the applied voltage is less than
1013 Hz, the ions respond.

Orientation polarization is even slower than ionic polarization. The relaxation time for
orientation polarization in a liquid is less than that in a solid. Orientation polarization
occurs, when the frequency of applied voltage is in audio range (1010 Hz).

Space charge polarization is the slowest process, as it involves the diffusion of ions
over several interatomic distances. The relaxation time for this process is related to
frequency of ions under the influence of applied field. Space charge polarization
occurs at power frequencies (50-60 Hz).
Frequency Dependence of dielectric constant
When a dielectric material is subjected to an alternating field, the polarization component
required to follow the field in order to contribute to the total polarization of the dielectrics. The
relative permittivity which is a measure of the polarization also depends on the frequency. The
dependence of ron frequency of the electric field is shown in the figure.

At very low frequency, the dipoles will get sufficient time to orient themselves
completely with the field and all types of polarization exist. Since the dielectric is characterized
by polarisability  ( = e + i + o ) at low frequency i.e at radiofrequency region the dielectric
constant will be due to all polarisability.

The orientation polarization, which is effective at low frequencies, is damped out for
higher frequencies. In the microwave region the dipoles fail to follow the field and the
polarisability reduces to ( = e + i), as a result r decreases to some amount.

In the IR region the ionic polarization fails to follow the field so the contribution of ionic
polarization dies away. In this region only electronic polarization contributes to the total
polarization. Therefore ( = e) the r still decreases and only electronic polarization exist.

We know that P  N e E   o ( r  1) E

N e
Then the relative permittivity is r  1 …(1)
o

In the ultraviolet region even the electron cloud could not follow the field and electronic
polarizability becomes almost zero and the permittivity becomes one.

 r X ray  1
For example at low frequency the dielecric constant of water at room temperature is
about 80, but it fall to about 1.8 in the optical region.
Frequency Dependence of dielectric loss:
Dielectric loss tends to be higher in materials with higher dielectric constants. This is the
downside of using these materials in practical applications. Dielectric loss is utilised to heat food
in a microwave oven: the frequency of the microwaves used is close to the relaxation frequency
of the orientational polarisation mechanism in water, meaning that any water present absorbs a
lot of energy that is then dissipated as heat. The exact frequency used is slightly away from the
frequency at which maximum dielectric loss occurs in water to ensure that the microwaves are
not all absorbed by the first layer of water they encounter, therefore allowing more even heating
of the food.

Ferroelectrics
Below certain temperature it is found that some materials spontaneously acquire an
electric dipolemoment. These materials are called as ferroelectric materials or ferroelectrics.The
temperature at which ferroelectric property of the material disappears is called as ferroelectric
Curie temperature.

Ferroelectric materials are anisotropic crystals which exhibit a hysteresis curve P versus
E which can be explained by domain hypothesis.

Ferro electricity: Ferro electric materials are an important group not only because of
intrinsic Ferro electric property, but because many possess useful piezo electric,
birefringent and electro optical properties.

The intrinsic Ferro electric property is the possibility of

 reversal or change of orientation of the polarization direction by an electric field. This
leads to hysteresis in the polarization P, electric field E relation , similar to magnetic
hysteresis. Above a critical
temperature, the Curie point T c , the spontaneous polarization is destroyed by thermal disorder.
The permittivity shows a characteristic peak at T c.

Piezo – Electric Materials and Their Applications: Single crystal of quartz is used for
filter, resonator and delay line applications. Natural quartz is now being replaced by synthetic
material.
Rochelle salt is used as transducer in gramophone pickups, ear phones,
hearing aids, microphones etc. the commercial ceramic materials are based on barium titanate,
lead zirconate and lead titanate. They are used for high voltage generation (gas lighters),
accelerometers, transducers etc. Piezo electric semiconductors such as GaS, ZnO & CdS are
used as amplifiers of ultrasonic waves.

Applications of Dielectric Materials:

Almost any type of electrical equipment employs dielectric materials in some form or another.
Wires and cables that carry electrical current, for example, are always coated or wrapped with
some type of insulating (dielectric) material. Sophisticated electronic equipment such as
rectifiers, semiconductors, transducers, and amplifiers contain or are fabricated from dielectric
materials. The insulating material sandwiched between two conducting plates in a capacitor is
also made of some dielectric substance.

Liquid dielectrics are also employed as electrical insulators. For example, transformer oil is a
natural or synthetic substance (mineral oil, silicone oil, or organic esters, for example) that has
the ability to insulate the coils of a transformer both electrically and thermally.
 1. Capacitors

Charge separation in a parallel-plate capacitor causes an internal electric field. A dielectric

(orange) reduces the field and increases the capacitance.

Commercially manufactured capacitors typically use a solid dielectric material with high
permittivity as the intervening medium between the stored positive and negative charges. This
material is often referred to in technical contexts as the capacitor dielectric.
The most obvious advantage to using such a dielectric material is that it prevents the conducting
plates, on which the charges are stored, from coming into direct electrical contact. More
significantly, however, a high permittivity allows a greater stored charge at a given voltage. This
can be seen by treating the case of a linear dielectric with permittivity ε and thickness between
two conducting plates with uniform charge density σε. In this case the charge density is given by

and the capacitance per unit area by

From this, it can easily be seen that a larger ε leads to greater charge stored and thus
greater capacitance.
Dielectric materials used for capacitors are also chosen such that they are resistant
to ionization. This allows the capacitor to operate at higher voltages before the insulating
dielectric ionizes and begins to allow undesirable current.
2. Dielectric resonator
A dielectric resonator oscillator (DRO) is an electronic component that exhibits resonance of the
polarization response for a narrow range of frequencies, generally in the microwave band. It
consists of a "puck" of ceramic that has a large dielectric constant and a low dissipation factor.
Such resonators are often used to provide a frequency reference in an oscillator circuit. An
unshielded dielectric resonator can be used as a Dielectric Resonator Antenna (DRA).
 3. Insulators-
Required Qualities of Good Insulating Materials: The required qualities can be
classified as under electrical, mechanical, thermal and chemical applications.
i) Electrical: 1. electrically the insulating material should have high electrical
resistivity and high dielectric strength to withstand high voltage.
2 .The dielectric losses must be minimum.
3. Liquid and gaseous insulators are used as coolants. For example transformer oil,
hydrogen and helium are
ii) Mechanical: 1. insulating materials should have certain mechanical properties
depending on the use to which they are put.
2. When used for electric machine insulation, the insulator should have sufficient
mechanical strength to withstand vibration.
iii) Thermal: Good heat conducting property is also desirable in such cases. The
insulators should have small thermal expansion and it should be non-ignitable.
iv) Chemical: 1. chemically, the insulators should be resistant to oils, liquids, gas
fumes, acids and alkali’s.
2. The insulators should be water proof since water lowers the insulation
resistance and the dielectric strength.
Other Applications:
Solid dielectrics are perhaps the most commonly used dielectrics in electrical engineering, as
very good insulators. Some examples include porcelain, glass, and most plastics.
Air, nitrogen and sulfur hexafluoride are the three most commonly used gaseous dielectrics.

Industrial coatings such as parylene provide a dielectric barrier between the substrate and its
environment.

Mineral oil is used extensively inside electrical transformers as a fluid dielectric and to assist in
cooling. Dielectric fluids with higher dielectric constants, such as electrical grade castor oil, are
often used in high voltage capacitors to help prevent corona discharge and increase capacitance.

Because dielectrics resist the flow of electricity, the surface of a dielectric may
retain stranded excess electrical charges. This may occur accidentally when the dielectric is
rubbed (the triboelectric effect). This can be useful, as in a Van de Graaff
generator or electrophorus, or it can be potentially destructive as in the case of electrostatic
discharge.

Piezoelectric materials are another class of very useful dielectrics which are used for transducers
and sensors.

Ferroelectric materials often have very high dielectric constants, making them quite useful for
capacitors.
Magnetic Materials
Classification of dia, para and ferromagnetic materials. Curie Temperature Hysterisis in
ferromagnetic materials. Soft and Hard magnetic materials. Applications.

Introduction
The materials that can be magnetised are called as magnetic materials
Magnetic dipoles and magnetic dipole moment
Any two opposite poles separated by distance constitute an magnetic dipole. A magnet is
a dipole which has north pole and south pole and the length of the magnet is the distance of
separation.
Magnetic dipole moment is the product of magnetic pole strength (m) and length of the magnet(l)
m  m.l
Magnetic field intensity (H)
The force experienced by a unit north pole ( of strength 1 Wb) placed at a point in
a magnetic field is a measure of the` field intensity’ or `field strength’

Magnetisation or Intensity of magnetisation (M)

Magnetization may be defined as the process of converting a non magnetic bar into a
magnetic bar

Magnetic Induction Or Flux Density(B)

Magnetic induction or magnetic flux density in an any material is the number of
lines of magnetic force passing through unit area perpendicular . Wb/m2

B   0 (M  H )
A
Magnetic Susceptibility (χ)
The ratio of the magnetization to the field strength
M

H
Permeability ()
The ration of the amount of magnetic density B to the applied magnetic field . It is used
to measure magnetic lines of forces passing through the material
B

H
Origin of Magnetic moment – Bohr Magneton
When ever a charged particle has an angular momentum , it contributes to permanent
dipole moment. Consider an hydrogen atom, electron revolving around the nucleus is equal to a
current loop. Orbital angular momentum arises due this current loop. The electron spin angular
momentum and nuclear spin angular momentum arises due to spin of the electron and nucleus
respectively.
There are three angular momentum of an atom
1. Orbital angular momentum of the electron
2. Electron spin angular momentum
3. Nuclear spin angular momentum
Total angular magnetic momentum
Bohr Magneton
The orbital angular momentum of an electron in an atom can be expressed in terms of
atomic unit of magnetic moment called Bohr Magneton.

eh
B 
4m
Classification of the magnetic materials
The magnetic materials are broadly classified in to two types. They are 1. Those atoms or
molecules do not have permanent dipole moments and 2. Those atoms or molecules have
permanent dipole moments even in the absence of external magnetic field.
Based on the magnetic moments the materials are classified as
Diamagnetic materials
Paramagnetic materials
Ferromagnetic materials
Anti ferromagnetic materials
Ferri magnetic materials

Diamagnetic materials
Dia magnetic materials has completely filled sub shell electronic structure resultant
magnetic moment is zero. There are no permanent dipoles and hence the magnetic effect are
small. When a diamagnetic material is placed in a magnetic field, there will be a small induced
magnetic moment which always oppose the applied field(accordance with Lenz`s Law). Due to
this effect the magnetic lines of forces expelled from the materials.
Mostly the covalent and ionic crystals exhibits the diamagnetic
properties. The magnetic susceptibility is small and negative and is
independent of temperature.
The examples of diamagnetic materials are 1. Covalent materials
such as Si,Ge, diamond, ii) some metals such as copper, silver, gold.
Para magnetic materials.

Atoms or molecules of paramagnetic materials have permanent magnetic moment

oriented in random direction. The magnetic interaction between the dipoles try to align themselves but
the thermal agitation disturb the alignment. In paramagnetic materials vector sum of magnetic
moments is zero in the absence of field.

When an external magnetic field is applied the partial alignment of permanent atomic
magnetic moments occur

When a magnetic field is applied , the individual magnetic moment takes the alignment
along the applied field as shown in figure . The magnetization of a paramagnetic material
increases with the increase in the applied field. Increase in temperature it reduces the
magnetization and destroys the alignment of dipoles with applied field.

Consider a paramagnetic material placed in non-uniform magnetic field. The paramagnetic

materials experience a net magnetic force towards the greater field. The magnetic susceptibility is
small and positive and is dependent on temperature. The susceptibility of the magnetic field is
given by
C

T
Where C is the curie temperature and T is the temperature in Kelvin scale.

The magnetization in ferromagnetic material is linear and gets saturated when a large magnetic
field is applied at low temperature.

The examples of paramagnetic materials are Mg, gaseous and liquid oxygen ,
ferromagnetic material ( Fe), and anti-ferromagnetic materials at high temperature and

ferromagnetic material (Fe3O4) at high temperature.

Ferromagnetic materials

Atoms or molecules of ferromagnetic materials have permanent

magnetic moment. In ferromagnetic materials all the dipoles are aligned
parallel as shown in the figure if a small value of magnetic field is applied,
a large value of magnetization is produced. As the ferromagnetic material
have permanent magnetic dipole moment and the susceptibility is positive.
The magnetization in ferromagnetic material is non linear and gets
saturated when a large magnetic field is applied.

A ferromagnetic materials exhibits two different properties. It behaves as a ferromagnetic

material below a certain temperature known as ferromagnetic curie temperature. Above the
temperature it behaves as a paramagnetic material. In the ferromagnetic region, it exhibits well
known curve known as hysteresis curve as shown in the figure.

The susceptibility of a ferromagnetic material above the ferromagnetic curie temperature

C
is given by  
T  f

Where C is the Curie constant and θf is the ferromagnetic Curie temperature.The

transition and rare earth metals such as Fe ,Co, Ni ,Gd are the examples of ferromagnetic
materials.

Hysteresis in ferromagnetic materials (B-H curve)

Below the ferromagnetic Curie temperature (T < θf ) Ferromagnetic material exhibits a
well known curve called hysteresis curve. The variation of B( magnetic induction) with
H(applied field) can be represented by a closed curve called hysteresis loop or curve. This refers
lagging of magnetization behind the magnetising field.
 If a magnetic field is increased gradually, the flux density increases and it becomes
maximum. The maximum value of flux density is called saturated magnetization.If the field is
reversed, the ferromagnetic materials is found to have magnetization in the absence opf external
field. This is called as retentivity or remanent magnetization (BR) and this property is called as
spontaneous magnetization. If the field is further reduced the flux density reduces to zero. The
field requird in the opposite direction to bring magnetization to zero is called as coercive field or
coercivity (-Hc). If the field is increased in oposite direction it attains saturation magnetization. If
an alternating field is applied a closed loop as shown in the figure is obtained.

According to Weiss, a virgin specimen of ferromagnetic material consist of number of

regions or domains(≈10-6 m or above) which are spontaneously magnetized. When magnetic
field is not applied the direction of spontaneous magnetization varies from domain to domain.
The resultant magnetization may hence be zero or nearly zero.
These domains are separated from other by a wall known as domain wall or Bloch wall The
domain concept is used to explain the hysteresis property. When an external field is applied two
possible ways of alignment domain growth are possible one by domain wall motion and other by
rotation of domain wall and domain growth is also reversible. Hysteresis curve is explained by
domain concept.

Antiferromagnetic matériels : These are the ferromagnetic materials in which equal no of

opposite spins with same magnitude such that the orientation of neighbouring spins is in
antiparallel manner are present.
Susceptibility is small and positive and it is inversely proportional to the temperature.

χ=C /(T+θ)
the temperature at which anti ferromagnetic material converts into paramagnetic material is
known as Neel’s temperature.

Examples: FeO, Cr 2 O 3 .
Ferrimagnetic materials: These are the ferromagnetic materials in which equal no of opposite
spins with different magnitudes such that the orientation of neighbouring spins is in antiparallel
manner are present.
Susceptibility positive and large, it is inversely proportional to temperature

χ=C /(T ± θ) T> T N ( Neel’s

temperature) Examples : ZnFe 2 O 4 , CuFe 2 O 4

Soft and Hard magnetic materials

Soft magnetic materials

The magnetic materials that are easy to magnetize and demagnetize are called as soft magnetic
materials.

Properties:

1. Low remanent magnetization

2. Low coercivity
3. Low hysteresis energy loss
4. Low eddy current loss
5. High permeability
6. High susceptibility

Examples of soft magnetic materials are

i) Permalloys ( alloys of Fe and Ni)
ii) Si – Fe alloy
iii) Amorphous ferrous alloys ( alloys of Fe, Si, and B)
iv) Pure Iron (BCC structure)

Applications of soft magnetic materials: Mainly used in electro- magnetic machinery and
transformer cores. They are also used in switching circuits, microwave isolators and matrix
storage of computers.
Hard magnetic materials
The magnetic materials that are difficult to magnetize and demagnetize are called as hard
magnetic materials.
Properties:

1. High remanent magnetization

2. High coercivity
3. High saturation flux density
4. Low initial permeability
5. High hysteresis energy loss
6. High permeability

7. The eddy current loss is low for ceramic type and large for metallic type.

Examples of hard magnetic materials are, i) Iron- nickel- aluminum alloys with certain
amount of cobalt called Alnico alloy. ii) Copper nickel iron alloys. iii) Platinum cobalt alloy.

Applications of hard magnetic materials: For production of permanent magnets, used in

magnetic detectors, microphones, flux meters, voltage regulators, damping devices and
magnetic separators.

Hard magnetic materials Soft magnetic materials

Difficult to magnetize and demagnetize Easy to magnetize and demagnetize
large hysteresis loop area small hysteresis loop area
Have large hysteresis loss Have very low hysteresis loss
The domain wall movement is difficult and it is Domain wall movement is relatively easier.
irreversible in nature Even for small change in the magnetizing
field ,magnetization changes by large
amount

The coercivity and retentivity are large The coercivity and retentivity are small
Magnetostatic energy is large Magnetostatic energy is small.

Small values of permeability and susceptibility Large values of permeability and

susceptibility
Used to make permanent magnets Used to make electromagnet
Examples- Examples-
Iron-nickel-aluminium alloys (alnicol) Fe-Si , Ferrous nickel alloys
Copper nickel iron (cunife)
,Ferrites,Garnets
Sample Questions:

Dielectric Materials:
1. Explain the phenomenon of electric polarization in dielectric materials?.
2. Describe in brief
(a)electronic polarization
(b) ionic polarization
(c) Orientation polarization
(d) Space charge polarisation with diagrams. Also find the total polarizability.
3. Differentiate between polar and nonpolar dielectrics.
4. Drive an expression for internal field in solids and liquids. Or Derive an experession for
for internal field by Lorentz method?
5. Derive Clausius-Mossoti equation.
6. What are ferroelectric materials? Describe in detail the Ferroelectric hysteresis.
7. Applications of Dielectric materials.
8. Derive the relation between dielectric polarization and dielectric constant?
9. What is its dielectric constant? Explain its importance in dielectric materials?
10. Which of the following properties are typical for dielectrics?
11. Write a note on
(a) Ferroelectricity (b) Dielectric constant (c) internal field in solids
12. Discuss the frequency dependence of various polarization processes in dielectric
materials.
13. What is dielectric loss? And also explain Dielectric Breakdown.
14. Describe the frequency dependence of dielectric constant.
15. Explain the applications of dielectric materials as insulators.
Magnetic Materials:
1. Define magnetization and show that B=  0 ( H  M )
2. Explain the classification of magnetic materials in detail?
3. Give important features of ferromagnetic materials. Explain the hysteresis curve on the basis
of domains.
4. What is hysteresis loss? Explain.
5. Distinguish between soft and hard magnets.
6. What is ferromagnetic Curie temperature? Discuss the behaviour of a ferromagnetic material
below the Curie temperature.
7. What are ferrites? Explain the magnetic properties of ferrites and mention their industrial
applications.
8. Write the importance of hard magnetic materials in engineering applications?
9. What are the applications of soft and hard magnetic materials?
Important formulae:
Problems
2.
 3. The dielectric constant of Sulphur is 3.4. Assuming a cubic lattice for its structure,
calculate the electronic polarizability for Sulphur.
Given: Sulphur density= 2.07 gm/cc, and atomic weight =32.07

Given data:
4. Find the polarization produced in a dielectric medium of relative permittivity 15 in
presence of an electric field of 500 V/m.

Given data:

1. In a magnetic material, the field strength is 106 Am-1. The magnetic susceptibility of the
material is 0.5X10-5. Calculate the intensity of magnetization and the flux density of the
material.


M B   0 (M  H )
 A
H
 4  10 7 (5  10 6 )
M  H  0.5  10 5  10 6  5
 1.257Wbm  2

2. If a magnetic field of 1800Am-1 produces a magnetic field 3 x 10-5 Wb in an iron bar of

cross sectional area 0.2cm2, Calculate permeability.

 B  0 r H
B  1.5Wbm 2
A B 1.5
r    663.14
H 0 4  10 7  1800

3. Calculate the saturation magnetization for Ni ferrite. The lattice parameter of a cubic unit
cell of Ni ferrite is 0.835nm and the magnetic moment per unit cell is 18.4B .
( B= 9.27 1024 )

Magneticmo ment 18.4  9.27 10 24

M  9 3
 2.929 10 5
volume (0.8353 10 )