Datasheet: uni L-SNB Rib 36%

EN

Plastic Modular Belt

Serie uni L-SNB Type Rib 36%
P Straight running belt
Nominal pitch: 50.0 mm (1.97 in)
R Surface type: Rib Top
Surface opening: 36%

STANDARD
Backflex radius: 140.0 mm (5.50 in)
T
ctio
n Pin diameter: 8.0 mm (0.31 in)
dire
ing
nn
Ru L
Photo will
be updated

Belt material mm in mm in
& color PP G PP-HW LB
P 50.0 1.97 T 16.0 0.63
(Nominal)
Pin and lock
material & color PP W PP G PP-HW LB PP-HW LB
R 6.0 0.23 L 8.0 0.31

STRAIGHT RUNNING
Non standard material and color: See uni Material and Color Overview.

Alternative pin and lock materials: Pin: PE W SS304

Permissible tensile force Belt weight Number of wear strips

(Belt/pin material) (Belt/pin material) *Min. No. (Min. No.)
Belt width drive
PP-HW/PP PP-HW/PP sprocket **Carry **Return
per shaft (pcs) (pcs)
mm in N lbf kg/m lb/ft

153 6.0 4559 1025 1.5 1.01 2 2 2

229 9.0 6826 1535 2.2 1.51 2 2 2

305 12.0 9093 2044 3.0 2.01 3 3 2

PITCH 50.0 MM/1.97 IN

381 15.0 11360 2554 3.7 2.51 3 3 2

457 18.0 13627 3063 4.5 3.01 4 4 2

533 21.0 15894 3573 5.2 3.51 4 4 2

609 24.0 18161 4083 6.0 4.01 5 5 3

686 27.0 20428 4592 6.7 4.51 5 5 3

762 30.0 22695 5102 7.5 5.02 6 6 3

838 33.0 24962 5611 8.2 5.52 6 6 3

914 36.0 27229 6121 9.0 6.02 7 7 4

990 39.0 29496 6631 9.7 6.52 7 7 4

Additional standard belt widths are available in steps of 76.1 mm (3.00 in)

1980 78.0 59004 13264 19.4 13.04 14 14 7

Additional standard belt widths are available in steps of 76.1 mm (3.00 in)

2969 116.9 88476 19889 29.1 19.55 20 20 10

General belt tolerance is +0/-0.4% at 23°C/73°F and 50% RH. For exact belt width contact Customer Service. Non standard belt width on request.
*Max. Load per Drive Sprocket. Belt material: PP-HW with snub roller 2000 N (450 lbf), PP-HW without snub roller 1250 N (281 lbf)
**Max. Spacing between wear strips, Carry: 152 mm (6 in.) ; Return: 304 mm (12 in.)
***Load capacity per row of reinforcement links in the belt: 2500 N (562 lbf)
***Example: Belt with 8 rows of reinforcement links, permissible load is 8 x 2500 N (562 lbf) = 20000 N (4496 lbf)
= Single Link
Accessories
Reinforcement Link

The use of uni-chains belts with the SS reinforcement /pitch control links in blanchers, cookers
and other high temperature applications will reduce belt elongation due to temperature by
more than 90%. This will simplify the belt take-up system and reduce maintenance.
uni-chains recommends three reinforcement links per K1200 module.
Note: Reinforcement links require the use of SS pins.

Type Material & color N/row Lbf/row

Steel Link SS316 2500 562

Non Standard material and color: See uni Material and Color Overview.

Accessories
Finger Plates
A A

Snap-On Snap-On
Cover Caps G F E Cover Caps
G F E

N
N Slider I Slider
O J
M K

H H
Type A Type B

Material A E F G
Type
& color mm in mm in mm in mm in

Single Sided 150x149

POM-LF BR POM-DI G 2.5 0.10 152.1 5.99 100.3 3.95 12.0 0.47
Single Sided 120x149

H I J K M N O

mm in mm in mm in mm in mm in mm in mm in

10.0 0.39 80.0 3.15 114.0 4.49 192.0 7.56 135.0 5.31 23.0 0.91 57.0 6.18

All uni-chains belt systems are available in a raised rib version that can be supplied with matc­­h­ing finger plates, alsocalled combs.
The finger plates are supplied with cover caps which can be attached when the finger plate has been installed. The cover caps can be removed by using a screwdriver that
can be in­serted between the cover and finger plate. In order to adjust to belt width variations caused by temperature fluctuations, a slider facilitates the sideways move-
ment of the finger plates.
Non Standard material and color: See uni Material and Color Overview.
Sprocket

Double row/Two way

Single row/One way

PA6 LG
A-dimen-
Bore size

diameter

diameter

diameter

B-dimen-

Machined PA6 N
Overall

Pitch-

Hub-

sion

sion
No of teeth

0.75

1.00

1.25
1.50

2.50
0.78
0.98

1.18

1.57
2.36

3.54
in
Pilot bore

Molded
20.0
25.0

30.0

40.0
60.0

90.0
19.1

25.4

31.8
38.1

63.5
mm

mm in mm in mm in mm in mm in

Z06 x 92.5 3.64 100.0 3.94 70.0 2.76 35.3 1.39 58.0 2.28 x x

Z08 x 128.7 5.07 130.7 5.15 70.0 2.76 52.4 2.06 73.3 2.89 x x

Z10 x 159.8 6.29 161.8 6.37 70.0 2.76 68.9 2.71 88.9 3.50 x x

Z10 159.8 6.29 161.8 6.37 120.0 4.72 68.9 2.71 88.9 3.50 x x

Z12 x 192.5 7.58 193.2 7.61 70.0 2.76 85.3 3.36 104.6 4.12 x x

Z12 192.5 7.58 193.2 7.61 120.0 4.72 85.3 3.36 104.6 4.12 x x

Z16 x 257.3 10.13 256.3 10.09 120.0 4.72 117.7 4.63 126.1 4.96 x x

Non standard material

Molded sprocket Molded sprocket Machined sprocket Machined sprocket and color: See uni
Material and Color
Overview.

Other sprocket sizes are available upon request.

Two-part sprocket are available upon request.
Round bores are always delivered with keyway.
Other bore sizes are available upon request.
uni Retainer Rings: See uni Retainer Ring data sheet
Width of tooth = 7.0 mm (0.28 in)
Width of sprocket = 42.3 mm (1.67 in)

Max load per sprocket shown does not take bore size into account.
Please also ensure that sufficient size shaft is chosen for corresponding load.

For correct sprocket position: See uni Assembly Instructions for uni L-SNB.
For more detailed sprocket information, contact Customer Service.
 uni L-SNB Rib 36%/161220

Expert advice, quality solutions Ammeraal Beltech Modular A/S

Transmission Belts
Conveyor Belts

Seamless Belts

and local service Hjulmagervej 21

Modular Belts

Timing Belts

Fabrication

for all your belting needs DK-7100 Vejle

& service

www.ammeraalbeltech.com
T +45 7572 3100
This information is subject to alteration due to continuous development. Ammeraal Beltech will not be held liable for the incorrect F +45 7572 3348
use of the above stated information. This information replaces previous information. All activities performed and services rendered by [email protected]
Ammeraal Beltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. www.unichains.com