Terluran GP-22

Acrylonitrile Butadiene Styrene (ABS)

Technical Datasheet

DESCRIPTION
Terluran GP-22 is an easy-flow, general purpose injection molding grade with high resistance to impact and heat distortion; intended for a
wide range of applications, particularly in the housings sector.

FEATURES APPLICATIONS
Excellent colorability Injection molding
Medium flow Appliance housings
Good impact resistance Household and sanitary appliances
Good heat distortion resistance Toys
High quality surface finish and gloss Automotive components

Property, Test Condition Standard Unit Values

Rheological Properties

Melt Volume Rate 220 °C/10 kg ISO 1133 cm³/10 min 19

Mechanical Properties

Izod Notched Impact Strength, 23 °C ISO 180/A kJ/m² 26

Izod Notched Impact Strength, -30 °C ISO 180/A kJ/m² 8

Charpy Notched Impact Strength, 23° C ISO 179 kJ/m² 22

Charpy Notched Impact Strength, -30° C ISO 179 kJ/m² 8

Charpy Unnotched, 23° C ISO 179 kJ/m² 180

Charpy Unnotched, -30° C ISO 179 kJ/m² 100

Tensile Stress at Yield, 23° C ISO 527 MPa 45

Tensile Strain at Yield, 23° C ISO 527 % 2.6

Tensile Modulus ISO 527 MPa 2300

Nominal Strain at Break, 23 °C ISO 527 % 10

Flexural Strength ISO 178 MPa 65

Hardness, Ball Indentation ISO 2039-1 MPa 97

Thermal Properties

Vicat Softening Temperature VST/B/50 (50°C/h, 50N) ISO 306 °C 96

Vicat Softening Temperature, VST/A/50 (50°C/h, 10N) ISO 306 °C 105

Contact us:
Page 1 of 3 Phone +49 2133 51 4007
Revision Date: 2013.08.21 [email protected]
www.styrolution.com
Terluran GP-22
Acrylonitrile Butadiene Styrene (ABS)

Property, Test Condition Standard Unit Values

Heat Deflection Temperature A; (annealed, 1.8 MPa) ISO 75 °C 94

Heat Deflection Temperature B; (annealed, 0.45 MPa) ISO 75 °C 99

Coefficient of Linear Thermal Expansion ISO 11359 10^(-6)/°C 80 - 110

Thermal Conductivity DIN 52612-1 W/(m K) 0.17

Electrical Properties

Dissipation Factor (100 Hz) IEC 60250 - 48E-4

Dissipation Factor (1 MHz) IEC 60250 - 79E-4

Relative Permittivity (100 Hz) IEC 60250 - 2.9

Relative Permittivity (1 MHz) IEC 60250 - 2.8

Volume Resistivity IEC 60093 Ohm*m 1E13

Surface Resistivity IEC 60093 Ohm 1E13

Other Properties

Density ISO 1183 kg/m³ 1040

Water Absorption, Saturated at 23°C ISO 62 % 1

Moisture Absorption, Equilibrium 23°C/50% RH ISO 62 % 0.22

Yellowness Index DIN 6167 - 13

Processing

Linear Mold Shrinkage ISO 294-4 % 0.4 - 0.7

Melt Temperature Range ISO 294 °C 220 - 260

Mold Temperature Range ISO 294 °C 30 - 60

Injection Velocity ISO 294 mm/s 200

Drying Temperature °C 80

Drying Time h 2-4

Typical values for uncolored products

SUPPLY FORM
Terluran® is delivered as spherical pellets. The bulk density of the pellets is from 0.55 to 0.65 g/cm³. Standard Packaging unit: 25 kg PE-bag
on palette, shrunk or wrapped with PE film or delivery in silo trucks. PE bags should not be stored outside. In dry areas with normal
temperature control, Terluran pellets can be stored for relatively long periods of time without any change in mechanical properties. Under poor
storage conditions, Terluran absorbs moisture, but this can be removed by drying.

Contact us:
Page 2 of 3 Phone +49 2133 51 4007
Revision Date: 2013.08.21 [email protected]
www.styrolution.com
Terluran GP-22
Acrylonitrile Butadiene Styrene (ABS)

PRODUCT SAFETY
No adverse effects on the health of processing personnel have been observed if the products are correctly processed and the production
areas are suitably ventilated. For styrene, acrylonitrile and 1,3-butadiene the maximum allowable workplace concentrations must be observed
according to the pertaining national regulations. In Germany, the following limit values are valid (Oct. 2002): styrene, MAK-value: 20 ml/m³ =
86 mg/m³; acrylonitrile, TRK-value: 3 ml/m³ = 7 mg/m³ and 1,3-butadiene, TRK-value: 5 ml/m³ = 11 mg/m³. According to EU directive
67/548/EWG, Annex I and TRGS 905 (Oct. 2002), acrylonitrile and 1,3-butadiene are classified as carcinogenic, category 2 (´substances
which should be regarded as if they are carcinogenic to man´) and 1 (substances known to be carcinogenic to man), respectively. Experience
has shown that during appropriate processing of Terluran with suitable ventilation the values obtained are well below the limits mentioned
above. TRGS 402 (Germany) can be used for determining and assessing the concentrations of hazardous substances in the air within
working areas. Inhalation of gaseous degradation products, such as those which may arise on severe overheating of the material or during
pumped evacuation, must be avoided. Further information can be found in our Terluran safety data sheets.

DISCLAIMER
The above information is provided in good faith. Styrolution is not responsible for any processing or compounding which may occur to product
finished articles, packaging materials or their components. Further, Styrolution MAKES NO WARRANTY OR REPRESENTATION OF ANY
KIND, REGARDING THE INFORMATION GIVEN OR THE PRODUCTS DESCRIBED, AND EXPRESSLY DISCLAIMS ALL IMPLIED
WARRANTIES, REPRESENTATIONS AND CONDITIONS, INCLUDING WITHOUT LIMITATION ALL WARRANTIES AND CONDITIONS OF
QUALITY, MERCHANTABILITY AND SUITABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Responsibility for use, storage, handling
and disposal of the products described herein is that of the purchaser or end user.

Contact us:
Page 3 of 3 Phone +49 2133 51 4007
Revision Date: 2013.08.21 [email protected]
www.styrolution.com