A.

SYSTEM FEATURES

1. INTER-FLAT COMMUNICATION:
Flat owner can communicate with any other flat owner by just dialing the
respective flat number (extension number)

2. TONE & PULSE DAILING:

You can connect any standard telephone instrument with Tone or/and Pulse
(10 pps) dialing mode. The System is capable of handling both type of dialing.

3. WAKE UP ALARM:
Each extension can ave their own morning larm/Reminder call. Time should
be entered in 24 Hrs basis (RAILWAY TIME) Example to set alarm at 4.30
PM i.e. 16.30 Hrs.

Step 1 : Dial “#766” wait for beep

Step 2 : Dial 16 wait for beep
Step 3 : Dial 30 wait for beep & hang up Programming error is
indicated by 8 beeps and if so happens above steps are to be repeated.

4. CALL HUNTING / SINGLE DIGIT SECURITY ACCESS:

Security man can be called by dialing single digit number with hunting for 2
or 3 or 4 extensions as per programmed extension numbers. In hunting mode
first system will look for the 1st extension if busy then only it jumps to the 2nd
Programmed extension , if that is also busy it jumps to the 4th programmed
extension.

5. ALL PARTY CONFERENCE:

Unlimited extensions can be on conference at a time. Procedure for
Conferencing :

Step 1 : press “flash”, during conversation

Step 2 : Dial required extension number & talk Repeat the above
Procedure to make conference with more people.

6. AUTO REDIAL OF MISSED CALL:

Any extension giving more than eight rings to other extension becomes a
registered incoming caller.
Procedure to call to the registered incoming caller / Missed call

Step 1 : Lift the handset.

Step 2 : Dial “#40”
Immediately last registered incoming caller’s extension start ringing.
7. CALLED NUMBER IDENTIFICATION:
Each extension can obtain the last 10 caled numbers through the display unit
installed at the security.
Procedure to get caller identification

Step 1 : Dial your security extension number and ask the security to
watch the display board
Step 2 : press “Flash”

Step 3 : press “#50” for last caller’s number

OR
: press “#51” for last but one caller’s number
OR
: press “#52” for last but 2nd caller’s number
: press “#59” for last but 9th caller’s number
Step 4 : Ask the security to read out the number appearing on his
display board.

8. CALL BARRING (NO MAN’S EXTENSION):

This feature helps to restrict the strangers/blank calls to the flat Any
extensions like LIFT,Terrace can be defined as NO MAN’s extension so that
from such extension you will only be able to contact security not to the flats.

Procedure for Defining NO MAN’S extensions.

From Master :

Step 1 : Dial “#713” – wait for beep.

Step 2 : Dial the required extension no.wait for beep

Procedure for Defining Normal extension

From Master :

Step 1 : Dial “#703” – wait for beep

Step 2 : Dial the required extension no. wait for beep

9. WATCH MAN’S WATCH DOG:

This Feature keeps watch on watchman whether he is sleeping during right
time. Watchman’s extension will ring at the predefined hours. (you can set 6
different alarm hours ) System stores wheather the watchman has lifted the
telephone or not. The details of each watchman’s result can be obtained
through display by punching the code. Maximum of 4 extensions you can
define as Watchman.

a) Procedure for defining the watchdog Manager. Only from this

extension you can activate and do necessary changes in alarm time and
watchman number.
From Master :

Step 1 : Dial “#736” – wait for beep

Step 2 : Dial the Watchdog Manager extension number
Note : Only one extension can be made as watchdog Manager.

b) Procedure for defining the watchman extension number :

From Watchdog Manager extension:

Step 1 : Dial “#731” – wait for beep

Step 2 : Dial - extension no. – wait for beep
Step 3 : Dial – extension no. – wait for beep
Step 4 : Dial – extension no. – wait for beep
Step 5 : Dial – extension no. – wait for beep hangup
Note : Maximum four extension can be defined as a watchman
extensions.

c) Procedure for defining the alarm time :

You can set 6 different time alarms , Time should be entered in 24 hrs.basis
(Railway Time)

From Watchdog Manager Extension :

Dial “#733”- 1 - HH – MM (For first alarm time)
----//----
“#733”- 2 - HH – MM (For second alarm time)
---//----
“#733”- 6 – HH – MM (For 6th alarm time)

Note : All above a, b & c procedures are stored permanently in the

Systems & need not be programmed every time.

d) Procedure to Activate :
From Watchdog Manager Extension :
Dial “#730”

This will activate watchman’s watch dog and will store the number of times
the extension has answered the ring.

e)Procedure to Decactivate :
From Watchdog Manager Extension :
Dial “#734”
This Will deactivate watchman’s watch dog.

f) Procedure to get display of watchdog’s details :

Dial ‘#735” – Extension number (Watchman extension)
 (if the dialed extension does not belong to watchman extension system give 8
beeps & there won’t be any change in the display unit.)

Display indicates as follows :

Display unit at the security

Number of times the extension has

answeredthe call

Total number of times the extension has

received ring.

10. SUPER CROSS CHECK :

In case of doubt on visitor, security can activate the features of super cross check.
This provides an auto ring after few minutes (as per programmed time) from
visitor’s entry for checking that visitor has entered the said flat or not. Four
extension will have super cross check facility. (usually the security extension)

Procedure to activate this feature

Step 1 : Dial the required Flat number as requested by visitor. Take

the Permission of the flat owner to send the visitor
Step 2 : After disconnecting Dial “#42”
System will give ring after pre-programmed time.And you
Can confirm visitor’s credentials.

Procedure to set the time period to reach the flat

From Master

Step 1 : Dial “#743” - wait for beep

Step 2 : Dial “ 2 “ - wait for beep
Step 3 : Dial “ XX” - wait for beep & Hang up.
( XX - 01 = 35 seconds
- 02 = 70 seconds )
Note : 1. No need to set time period every time.
(set only once during installation)
2. DIP switch Setting : Refer DIP switch setting page 23-24
11. PANIC ALERT CODE “#0” :
In case of emergency lift the handset & Dial “#0”. Immediately display will show
your flat number with siron.

Note : Press the panic cod in extreme emergency only.

12. SIMULTANEOUS EMERGENCY DIALING :

In case of emergency you can dial “#777” from your extension so that it will give
Ring simultaneously at four pre-programmed extensions.Whenever anyone or
More responds to your call can have the conversation with you.

Procedure for programming the four required extension for emergency ringing.

From your extension :

Step 1 : Dial “#723” - wait for beep

Step 2 : Dial - extension no. - wait for beep
Step 3 : Dial - extension no. - wait for beep
Step 4 : Dial - extension no. - wait for beep
Step 5 : Dial - extension no. - wait for beep hang-up

Note : Max. four extensions can be programmed.

13. UNIQUE PANIC ALERT TO EVER FLAT BY SECURITY INCASE OF AN

EMERGENCY :
In case of emergency at the security he can dial “#777” from his instrument.
At that time all extensions will start ringing. Whoever lifts the handset can have
conversation with the security. This will continue till the security keeps his
receiver down.

14. BARGE IN FROM SECURITY & KEY PERSONNEL :

If the dialed extension is busy ( in conversation with other extension ) you can
barge in between the conversation of that extension ( This feature is useful in case
of any important message to be passed to that extension ).

How to barge in

Step 1 : Dial the extension number and get busy tone.

Step 2 : Dial ‘#44” You can now talk to that extension.

Note : This is a restricted facility. For this facility to be allowed to any

extension you have to program the system from the master
extension.
Procedure for programming barge in facility
From Master
 Step 1 : Dial # 710 - wait for beep
Step 2 : Dial the required extension numbers wait for beep

Procedure for removing barge in facility

From Master

Step 1 : Dial #700 - wait for beep

Step 2 : Dial the required extension no. –wait for beep

Note : You will hear signal beep tone when any extension barges in
between your conversation.

15. AUTO CALL BACK :

If the dialedextension is busy. Dial #48 and replace the handset. You will get ring
after the busy extension no. gets free.

16. FOLLOW ME FOR CALLS TO BE RE –DIRECTED :

When you are not at home, incoming calls can be forwarded to any other
extension as per your requirement.

Procedure for Call forwarding :

Step 1 : press #41.

Step 2 : press required extension no.

After this any extension calling your extension will automatically land at the
Forwarded Extension.
Forwarded line will be indicated at the security on his display as soon ashe dials
your extension number.

Cancellation of call Forward

Step 1 : press #41 and hang up

Note : DIP switch Setting :Refer DIP switch setting page 23-24

17. DO NOT DISTURB :

When you are in some important work and not to be disturbed by any telephone
Calls you can activate this feature. This feature will be activate till you deactivate
It or any power failure.

Procedure for activating this feature :

Step 1 : Dial “#47”, hang up

Your dial tone will get changed.
 Procedure for deactivating this feature :

Step 1 : Dial “#47” hang-up

Your dial tone will get changed to normal dial tone
Note : DIP switch Setting : Refer DIP switch setting page 23-24

18. HOT LINE :

System allows you to select one extension number ( Hot line number ) Which is a
Automatically dialed after a delay of three seconds from lifting the handset.
Procedure to set up a hot line number.

Step 1 : press #722 wait for beep

Step 2 : press desired extension number & hang up

Procedure to cancel hotline number

Press #722 wait for three beeps & hang up

19. REAL TIME CLOCK SETTING :

The timing on display can be changed from the Master extension by following
Program.

Step 1 : Dial #760 - wait for beep

Step 2 : Dial “HH” - wait for beep
Step 3 : Dial “MM”- wait for beep & hangup
“HH” –Hour in 24 hours mode from 00 to 23
“MM”-Minutes from 00 to 59
Immediately display will change to present feed time

20. PANIC ALERT CHECK (available in WALL MOUNT Model only) :

To Check panic alerts registered at the Security. Dial # 45 from display.
extension. The display will indicate the last 10 flat no. Who has given the panic
alerts.
 B) OPTIONAL FEATURES

1. PRESIDENT BROADCAST :
Any message can be stored in the system. Which will be announce to every
Extension goes off hook.

Procedure for programming :

Step 1 : Dial #3 Beep

Step 2 : Dial XXX (Password)
Step 3 : Dial Code
Code -1- For Recording the message
-2- To play the message
-3- To Activate
-4- To Deactivate
-5- For change password
-6- To Activate with Ring in multiple of 4 extension at a time
And cover all extensions (3 Ring each)
(Note : Factory set password is 119)

2. TALKING CALLED IDENTIFICATION :

System will store last 10 or 3 calls as talking called numbers for each extension.

Procedure to get callers identification through voice

Step 1 : lift the handset and get dial tone.

Step 2 : Dial #50 – for last callers number.
Or
#51 - for last but one caller’s Number
Or
#52 - for last but 2nd callr’s Number
Or
#59 - for last but 9th caller’s Number
Immediately system will announce the extension number who has called.

3. VENDOR ALARM :
This facility informs you the arrival /availability of the vendor

Vendor activation code :

“#21” - PAVWALA
“#22” - BHAJIWALA
“#23” - DOODHWALA
“#24” - PLUMBER
“#25” - ELECTRICIAN
How to activate vendor alarm

Step 1 : lift the hand set

Step 2 : dial the required vendor activation code & hangup
Above procedure stores your request for the vendor.

How it helps :
Your telephone instrument starts ringing. When your programmed vendor arrives.
As soon as you lift the handset system will also announce (voice prompt) the
Name of the vendor available to remind you to avail his service and it
Automatically deactivates your request for the vendor.

Manual deactivation of vendor request

vendor Deactivation code :
“#11”- PAVWALA
“#12” - BHAJIWAL
“#13” - DOODHWALA
“#14” - PLUMBER
“#15” - ELECTRICIAN

How to deactivate manually the vendor request

Step 1 : lift the hand set
Step 2 : dial the required vendor deactivation code & hangup
Above procedure clears your request for the vendor.

How it helps :
While activating the vendor alarm by mistake if you have dialed wrong vendor,
You can clear it by above steps.

INSTRUCTION FOR VENDORS :

After arrival of vendor in the gate the respective code should be pressed by
Respective vendor from the security extension.

Activation Code :
“#21” - PAVWALA
“#22” - BHAJIWALA
“#23” - DOODHWALA
“#24” - PLUMBER
“#25” - ELECTRICIAN

How to activate :

Step 1 : lift the hand set

Step 2 : dial the required activation code & hangup
This stores the arrival of the vendor. System voice prompts to the extension who
Have activate the request for the particular vendor.
 While vendor is going back after finishing the work, he has to deactivate the
alarm by dialing his deactivation code from any of the lobby/security extension.

Deactivation code :
“#11”- PAVWALA
“#12” - BHAJIWALA
“#13” - DOODHWALA
“#14” - PLUMBER
“#15” - ELECTRICIAN

How to deactivate

Step 1 : lift the hand set

Step 2 : dial the required deactivation code & hangup

4. ELECTRONIC DOOR SENSOR INTERFACE :

 If your flat is fitted with a door sensor, it will give alarm when any
unauthorized entry takes place.
 Door sensor consists of lock and key fitted next to your door.
 Lock & key is used to activate and deactivate the door sensor.

Operation of the Door Sensor :

 To activate the door sensor, keep the lock in arm mode.
 To deactivate the door sensor, keep the lock in disarm mode
(yellow / blue dot)
 When the sensor is on active mode, a 3 digit password to be dialed from
any extension prior opening of the door else alarm will sound.

Dialing of password
Go to any extension
Press #6 followed by our extension / flat number
Dial your password

To change your password

From your extension
Dial #752 followed by your old password
Dial your new password and hang up

Note :
 You can have only one valid entry or exit after dialing your password
 Deactive the sensor as soon as you enter your house to prevent unintended
alarm
 Initially for flats, password have been set to 119
5. CALLER ID INTERFACING FACILITY :
Any standard telephone instrument having CLIP (DTMF type) or separate Caller
ID (DTMF type) equipment can be connected to the extension. This will display
the extension number from where you are receive the call.
This is a restricted facility, for this facility to be allowed to any extension you
have to programme the system from the master extension.

Procedure for programming Caller ID facility :

From Master

Step 1 : Dial # 711 - wait for beep

Step 2 : Dial the required extension numbers – wait for beep

Procedure for removing Caller ID facility :

From Master

Step 1 : Dial #701 - wait for beep

Step 2 : Dial the required extension numbers – wait for beep

6. PANIC ALERT BUTTON :

There is a separate Panic Alert Button fitted next to your instrument, In case of
emergency, press the Panic Alert button. Alarm Bell/Siron will ring at the
Security with your Flat No. flashing on the display board.
Note : Press the panic in extreme emergency only.

Dip :1) Dip Switch no.4 in CPU card (WALL MOUNT Model) should be in ‘ON’
position
for thisfeature to be active
2) DIP switch no.8 (TABLE TOP MODEL) should be in ‘ON’ position
for this feature to be active

7. CABLE TAMPER ALERT:

To activate this feature, the extension telephone should be terminated with resistor
as directed.

Procedure to enable cable tamper alert :

From Master :
Step 1 : Dial “#712”
Step 2 : Dial the required extension numbers, wait for beep

Procedure to deactivate cable tamper alert :

Step 1 : Dial “#702”
Step 2 : Dial require Exp. No.
This Procedure is required only during installation.
 Note : 1. DIP switch no.4 (WALL MOUNT Mode) should be in ‘ON’
position for this
feature to be active
2. DIP switch no.8 (TABLE TOP MODEL) should be in ‘ON’
Position for this feature to be active

8. PAGING FACILITY :
From any extension Dial “#49” You will directly get into the paging announcing
Port . If the paging port is busy you will get busy tone.

C) FLEXIBLE NUMBER PROGRAMMING

(Applicable for WALL MOUNT model) &
(TABLE TOP Models)

ENTERING PROGRAMMING MODE :

DIAL “#759 – XXX” FROM ANY EXTENSION
XXX = PASSWORD (DEFAULT PASSWORD IS 119)
DIAL TONE WILL GET CHANGED TO PROGRAM MODE TONE
FURTHER REFERRED AS Programme Mode Tone
DIAL # AT ANY STAGE OF PROGRAMMING TO GET BACK TO
Programme Mode Tone.

1. DEFINING EXTENSION NUMBER :

Programme Mode Tone
Dial 200-PP-NN…*
PP = Port no. from 01 to 64 - in WALL MOUNT Model
PP = Port no. from 001 to 256 in TABLE TOP MODELS
NN= Extension Number can be 2/3/4 or 5 Digits
You have to Dial “*” After 2/3/4/5 Digit extension number if single Digit 9/8
Acess is Enable then you cannot start the extension number by 9/8.
Eg : Define port 01 or 001 as extension 101
Dial 200-01-101 * or Dial 200-001-101*
Note : As a confirmation of the programme, System will give a beep over
telephone handset, and CPU buzzer buzzes once. If programmed extension
number already exists or any conflict in extension number like 100 already
exists & you are trying for programming extn. No. 1000, system will give
error tone of 8 beeps & CPU buzzer won’t buzz.

2. ERASING / DELETING PARTICULAR PORT :

If by mistake or wrong programme happens, you can erase that by the following
 Programme.

Programme Mode Tone

Dial 201 - PP (PP = 2 digit Port Number in WALL MOUNT Mode )

( PP = 3 digit Port Number in TABLE TOP MODELS )
This will blank he extension number of particular port.

3. DIFINING DISPLAY PORT :

System can handle 15 different (independent) displays with can be assigned to
Different ports. Normally display will indicate time & whenever that particular
port gets an incoming call. It displays the calling extn. No.
For defining port & its display no :

Program Mode Tone

Dial 202-PP-DD
PP = port No. where display is connected.
DD= Display No. (01 to 15) it’s respective display
00 = will erase the display assigned to the port.

Eg. = For defining port 01 as display 01.

Dial 202-01-01

4. SINGLE DIGIT SECURITY ACCESS BY CODE 9

Program Mode Tone

Dial 901-PP-PP-PP-PP
PP = Port Number From 01 To 64 - in WALL MOUNT Model
001 To 256 - in TABLE TOP MODEL
Note : For Operational Details, Ref System Features Sr.No.4
E.g.. : Defining port No.02,04 as a security access by code 9 with call hunting
Dial 901-02,04

Removing single digit access by 9

Dial 900
Note : call hunting ports : Max 4 ports can be defined as single digit access.

5. SINGLE DIGIT SECURITY ACCESS BY CODE 8

Program Mode Tone

Dial 801-PP-PP-PP-PP
 PP = Port Number
Note : For operational Details, Ref System Features Sr.No.4
E.g : Defining Port No. 24,25 as a security access by code 8
Dial 801-24,25

Removing single digit access by 8

Dial 800

6. DEFINING MASTER EXTENSION :

Program Mode Tone

Dial 203 PP
Note : master is required for different programming like RTC time changing,
Barge in prog,etc

7. DEFINING PORT AS A SECURITY EXT. OR COMMEN UTILITY

EXTENSIONS :

Programme Mode Tone

Dial 204-PP-PP-PP…P.P
From this extensions 1) Call forword can not enabled.
2) DND can not be enabled.
3) Can be defined as no men’s extn.
4) Can be defined as Watchmen security extn.
5) Can be defined as super cross check extn.
( Ref.system features 10.)

8. DISABLE SECURITY EXTENSIONS :

Program Mode Tone

Dial 205-PP-PP-PP-PP = Port No.
This is useful for defining as a normal Extensions.

9. DEFINE DISPLAY NUMBER FOR PANIC INDICATION :

In case of multiple displays to select, each wing display for panic indication
Independently, below programming is useful.

Program Mode Tone

Dial 400-DD-PP-PP-PP
PP = Port No.
DD = Display No.

Display 01 : ‘A’ wing lobby, port 01 to 28

Dial 400-01-01,02,03….28
Display 02 : ‘B’ wing lobby, port 29 to…. 63
Dial 400-02-29,30,31….63
10. ENABLE THE DISPLAY AS GENERAL DISPLAY FOR PANIC

Program Mode Tone

Dial 401-DD-DD …. DD = Display No.

11. DISABLE THE GENERAL DISPLAY AS GENERATED FOR PANIC

Programme Mode Tone

Dial 402-DD-DD
DD = Display No.

12. ENABLE SUPER CROSS CHECK PORTS :

Programme Mode Tone

Dial 902-PP-PP-PP-PP
PP = Port No.
REF : SYSTEM FEATURE 10

13. VOICE ANNOUNCEMENT :

This is available only when Talking caller ID card is installed in the system.
 For getting the port number
lift the handset and dial “#48”
 For getting the extension number
lift the handset and dial “#44”

14. TO DEFINE PORT WISE EXTENSION NUMBERS :

To define the extension nos.in fast mode.
Dial 207 - (System 1st Display ) will show Port No.
- Dial Extension No. * (max 5 Digit Extn.No.)
- After System acceptance, display will show next port no.
- Dial Next Extn No. & So On.

15. TO CHECK EXTENSION NUMBER ALLOWED TO PORT :

Dial 206 - Port No.
- Immediately Display1 will indicate the Ext.No. of that port
- For Next – Dial 6
- For Previous – Dial 4

16. FACTORY SET OF EXTENSION NUMBERINGS :

By this programme system numbers will get changed to factory set Nos.
After factory set program
Extension numbering will be set from 200, 201, 202……
 With port Nos. – 01/001, 02/002, 03/003……
Note : System CPU start buzzing, wait till the end of buzz

Programme Mode Tone

Dial 299-22-22-20

17. SET OF SECURITY AND DISPLAY EXTENSION

Programme Mode Tone
Dial 299-22-22-21
First Extension will Become Display Port
(i.e. Port No. 01 - Ext 200- Display Port)
Note : System CPU : start buzzing, wait till the end of buzz

18. ERASING ALL PORTS

All ports of systems will become blank
Programme Mode Tone
Dial : 299-22-22-23

19. CHANGING PASSWORD

Programme Mode Tone
Dial 300 – ppp (3 digit password)

20. RESETING PASSWORD THROUGH HARDWARE (in WALL MOUNT

model)
If you forgot the password or is erased due to power fluctuationa, Do following to
reset the password.
Step 1 - Switch off the system
Step 2 - Short the 2 pin stub labled at U-32 in the CPU with the help of the screw
driver or any conducting material.
Step 3 - Switch on the system by keeping the 2 pin stub shorted.
Step 4 - Remove the shorting of the 2 pin stub.
Now the programming password will become 119 (Default Password)

D. TECHNICAL DETAILS

A) WALL MOUNT (Wall Mountable System Up To 64 Lines)

 WALL MOUNT security intercom system has the following cards

1. CPU CARD
2. SUBSCRIBER CARD
3. POWER SUPPLY CARD
4. MAINS TRANSFORMER

1. CPU CARD:
Central Processing Unit (CPU) card controls the functioning of the system. It is
based on Intel 89c52 Microcontroller with time division multiplex technology. The
major functions like sensing of on/off hook, dialing,ringing,voice switching,display
signaling of each extension is handled by software programmed in the flash
memory of micro controller. Real time clock (rtc) with battery back up is interfaced
to microcontroller for updating time. The tone (dtmf) Dialing signal decoding
circuit is also placed in the cpu.

2. SUBSCRIBER CARD:
Each subscriber card is capable of handling 16 extensions intercom lines, Functions
Of sub card are as under.
a) Generating line voltage of 24V for each line with the 36 mA line current
b) Generating ring voltage of 75V rms for each line
c) Decording of on/off hook of each line
d) Decording cable tamper / panic of each line
e) Encoding & Decoding of voice switch

3. POWER SUPPLY CARD:

Generates following output voltages
CN 3 & CN 4 - to Subcards

CN 2 To CPU Card
A) 5V dc – 1 Amp
B) 24V dc – 1 Amp
C) 75V rms – 100MA
Protection fuses are provided on power supply card
F1 – 24V, F2 – 5V, F3 – 75VAC with fuse & Mov protects.

4. MAINS TRANSFORMER :
Primary Voltage rating :- 230V AC 50 HZ
Secondary Voltage rating :-
1) 24V AC 1 Amp
2) 9.2V AC 1 Amp
3) 75V AC 0.1 Amp
Or as mentioned on transformer :
B) TABLE TOP MODEL
(Table Top Systems)
TABLE TOP MODEL Systems containts following cards
 1) CPU CARD
2) SUBSCRIBER CARDS
3) MOTHER BOARD
4) PRESIDENT BROADCAST CARD (PRS) :
5) TALKING CALLER ID CARD :
6) POWER SUPPLY CARD :
7) MAINS TRANSFERMER :

1. CPU CARD :
Central Processing Unit (CPU) card controls the functioning of the system. It is
based on Intel 89c52 Microcontroller with time division multiplexing technology.
The major functions like sensing of on/off hook, dialing, ringing, voice switching,
display signaling of each extension is handled by software programmed in the flash
memory of micro controller. Real time clock (rtc) with battery back up is interfaced
to microcontroller for updating time. The tone (dtmf) dialing singnal decoding
singnal decoding circuit is also placed in the cpu.

2. SUBSCRIBER CARD :
Each subscriber card is capable of handling 16 extensions.functions of sub. Card:
A) Generating line voltage of 48v for each line with 35mA line current.
B) Generating ring voltage of 75v rms for each line
C) Decoding of on/off hook of each line
D) Decoding cable tamper of each line
E) Encoding and decoding of voice switch

3. MOTHER BOARD :
Mother board is the main connecting unit of CPU, Sub Cards. MDF and power
Supply. Since the system is a modular CPU and Subscriber Cards are interconnected
Through Motherboard with the help of 96 pin euro connector.

4. PRESIDENT BROADCAST CARD :

This decodes the voice in the digital form with the sampling rate of 8khz and stores
in the flash memory.

5. TALKING CALLER ID CARD :

In the talking caller id card the voice required to announce the extension number
And also for the vendor alarm are stored. This voice is played back whenever any
Extension activates the Vendor Alarm or Caller ID feature.

6. POWER SUPPLY CARD :

Generates following output voltages
A) 5V dc - 3Amp
 B) 24 dc - 1 Amp
C) 48 dc - 3 Amp
D) 75V rms - 300mA
CN-1 & CN-3 omleela connectors of power supply card are connected to the output
Of transformer & called input connector.
CN-2 & CN-4 are out-put voltage omleela connector as shown

CN 2

CN 4
Fuses :
Fs 1 - 5V -3Amp
Fs 2 - 24V - 2Amp
Fs 3 - 75 Rms -Ring - 0.5 Amp

7. MAINS TRANSFORMER :
Secondary Voltage Ratings are as shown below
1) 15V-3 Amp
2) 24V-1 Amp
3) 48V-1 Amp
4) 75 Rms – 0.1 Amp

E) DIP SWITCH SETTING

A. FOR WALL MOUNT MODEL

1. DIP Switch Setting on CPU card :

The facilities like DND, Panic button, Cable tamper Alert super cross check and
Follow me can be enabled or disable through DIP switch in CPU card :

DIP Switch no. ON OFF Description

1 Enable Disable Follow Me
2 Enable Disable Supercross Check
3 Enable Disable Do Not Disturb
4 Enable Disable Panic / Cable
Tamper Alert

2. DIP Switch Setting on sub card :

Following is the DIP Setting for selecting that sub card.
DIP No.1 DIP NO.2 DIP No.3 DIP No.4 Card No. Extensipn/
Ports
On On On On One 1 to 16
Off On On On Two 17 to 32
On Off On On Three 33 to 48
Off Off On On Four 49 to 64

B. FOR TABLE TOP MODEL

Dip Switch Setting in CPU card for selection of sub. Cards are as shown below

DIP DIP DIP DIP SUB CARD

SW.NO.1 SW.NO.2 SW.NO.3 SW.NO.4 NUMBER
ON ON ON ON ONE
ON ON ON OFF TWO
ON ON OFF ON THREE
ON ON OFF OFF FOUR
ON OFF ON ON FIVE
ON OFF ON OFF SIX
ON OFF OFF ON SEVEN
ON OFF OFF OFF EIGHT
OFF ON ON ON NINE
OFF ON ON OFF TEN
OFF ON OFF ON ELEVEN
OFF ON OFF OFF TWELVE
OFF OFF ON ON THIRTEEN
OFF OFF ON OFF FOURTEEN
OFF OFF OFF ON FIFTEEN
OFF OFF OFF OFF SIXTEEN

SW NO. ON OFF DESCRIPTION

5 ENABLE DISABLE FOLLOW ME
6 ENABLE DISABLE SUPERCROSS CHECK
7 ENABLE DISABLE DO NOT DISTURB
8 ENABLE DISABLE PANIC/CABLE ALERT

F) REMOTE DISPLAY UNIT

Display is seven segment LED displays are of size 2.3 inch or 1 inch. It has its own
 Voltage regulation circuits. Display consists of Micro-controller 89c51. The
Communication between system CPU card and display card is serial
Communication of rs.485 with baud rate of 9600 bits/sec.The hooter controlling
Is also the function of the display as per the CPU command. Normally this will
Display the time. When any extension calls the security immediately it indicates
The calling number. Whenever there is any emergency this will indicate the flat
Number with hooter.

DISPLAY CONNECTIONS :
A remote display units installed at security gate/lobby etc.are interfaced to the
Main system through the 9 pin D type male cable provided with display unit. In
Long distance case a quality twisted cable is preferred

D9 Cable Connections are as shown

Descriptions D9 to System D9 to Display

Not Used 1 1
Signal H 2 2
Not Used 3 3
+ 24 V DC 4 4
+ 24 V DC 5 5
Not Used 6 6
Signal L 7 7
Gnd 8 8
Gnd 9 9

DIP / JUMPER SETTING TO DEFINE DISPLAY NO :

In case of multiple RDU’s, to select the particular display, DIP/JUMPER setting is
Required.
SEVEN SEGMENT (SMALL : 1 inch ) Display :
Jumper J-B setting on display card are as shown below : Sr. from bottom JB. 1

Display No. JB.1 JB.2 JB.3 JB.4

01 OPEN OPEN OPEN OPEN
02 SHORT OPEN OPEN OPEN
03 OPEN SHORT OPEN OPEN
04 SHORT SHORT OPEN OPEN
05 OPEN OPEN SHORT OPEN
up to 15 nos.

SEVEN SEGMENT (BIG : 2.3 inch ) Display :

DIP switch setting on display card are as showm below.
Display No. Dip-1 Dip-2 Dip-3 Dip-4

01 ON ON ON ON
02 OFF ON ON ON
03 ON OFF ON ON
04 OFF OFF ON ON
05 ON ON OFF ON
up to 15 nos.

***
CUSTOMER’S DETAILS

CUSTOMER’S NAME : ________________________________________

DATE OF INSTALLATION

MASTER EXTN.NO. :

MDF COLOUR CODES

D1 D2 D3 D4
SR COLOUR PRT EXT NO PRT EXT NO PRT EXT NO PRT EXT NO
NO NO. NO NO

1. Blue-white 001 017 033 049

2. Orange –white 002 018 034 050

3. Green-white 003 019 035 051

4. Brown-white 004 020 036 052

5. Gray-white 005 021 037 053

6. Blue-Red 006 022 038 054

7. Orange – Red 007 023 039 055

8. Green- Red 008 024 040 056

9. Brown- Red 009 025 041 057

10. Gray- Red 010 026 042 058

11. Blue-Yellow 011 027 043 059

12. Orange –Yellow 012 028 044 060

13. Green- Yellow 013 029 045 061

14. Brown- Yellow 014 030 046 062

15. Gray- Yellow 015 031 047 063

16. Blue – Black 016 032 048 064

D5 D6 D7 D8
SR COLOUR PRT EXT NO PRT EXT NO PRT EXT NO PRT EXT NO
NO NO. NO NO

1. Blue-white 065 081 097 113

2. Orange –white 066 082 098 114

3. Green-white 067 083 099 115

4. Brown-white 068 084 100 116

5. Gray-white 069 085 101 117

6. Blue-Red 070 086 102 118

7. Orange – Red 071 087 103 119

8. Green- Red 072 088 104 120

9. Brown- Red 073 089 105 121

10. Gray- Red 074 090 106 122

11. Blue-Yellow 075 091 107 123

12. Orange –Yellow 076 092 108 124

13. Green- Yellow 077 093 109 125

14. Brown- Yellow 078 094 110 126

15. Gray- Yellow 079 095 111 127

16. Blue – Black 080 096 112 128

D9 D10 D11 D12

SR COLOUR PRT EXT NO PRT EXT NO PRT EXT NO PRT EXT NO
NO NO. NO NO

1. Blue-white 129 145 161 177

2. Orange –white 130 146 162 178

3. Green-white 131 147 163 179

4. Brown-white 132 148 164 180

5. Gray-white 133 149 165 181

6. Blue-Red 134 150 166 182

7. Orange – Red 135 151 167 183

8. Green- Red 136 152 168 184

9. Brown- Red 137 153 169 185

10. Gray- Red 138 154 170 186

11. Blue-Yellow 139 155 171 187

12. Orange –Yellow 140 156 172 188

13. Green- Yellow 141 157 173 189

14. Brown- Yellow 142 158 174 190

15. Gray- Yellow 143 159 175 191

16. Blue – Black 144 160 176 192

D13 D14 D15 D16

SR COLOUR PRT EXT NO PRT EXT NO PRT EXT NO PRT EXT NO
NO NO. NO NO

1. Blue-white 193 209 225 241

2. Orange –white 194 210 226 242

3. Green-white 195 211 227 243

4. Brown-white 196 212 228 244

5. Gray-white 197 213 229 245

6. Blue-Red 198 214 230 246

7. Orange – Red 199 215 231 247

8. Green- Red 200 216 232 248

9. Brown- Red 201 217 233 249

10. Gray- Red 202 218 234 250

11. Blue-Yellow 203 219 235 251

12. Orange –Yellow 204 220 236 252

13. Green- Yellow 205 221 237 253

14. Brown- Yellow 206 222 238 254

15. Gray- Yellow 207 223 239 255

16. Blue – Black 208 224 240 256