Cellular Communications

Definition
A cellular mobile communications system uses a large number of low-power wireless transmitters to
create cells—the basic geographic service area of a wireless communications system. Variable power
levels allow cells to be sized according to the subscriber density and demand within a particular region.
As mobile users travel from cell to cell, their conversations are "handed off" between cells in order to
maintain seamless service. Channels (frequencies) used in one cell can be reused in another cell some
distance away. Cells can be added to accommodate growth, creating new cells in unserved areas or
overlaying cells in existing areas.

Overview
This tutorial discusses the basics of radio telephony systems, including both analog and digital systems.
Upon completion of this tutorial, you should be able to accomplish the following:
1. describe the basic components of a cellular system
2. identify and describe digital wireless technologies

Topics
1. Mobile Communications Principles
2. Mobile Telephone System Using the Cellular Concept
3. Cellular System Architecture
4. North American Analog Cellular Systems
5. Cellular System Components
6. Digital Systems Self- Test
Correct Answers

Evolution of Mobile Radio Communications

Introduction:
In 1897, Guglielmo Marconi first demonstrated radio’s ability to provide continuous contact with
ships sailing the English channel.
During the past 10 years, fueled by
Digital and RF circuit fabrication improvements
New VLSI technologies
Other miniaturization technologies (e.g., passive components)
The mobile communications industry has grown by orders of magnitude.
The trends will continue at an even greater pace during the next decade.
 Fig. Illustrating the growth of Mobile Communication

In 1934, AM mobile communication systems for municipal police radio systems.

Vehicle ignition noise was a major problem.
In 1946, FM mobile communications for the first public mobile telephone service
Each system used a single, high-powered transmitter and large tower to cover
distances of over 50 km.
Used 120 kHz of RF bandwidth in a half-duplex mode. (push-to-talk release-tolisten
systems.)
Large RF bandwidth was largely due to the technology difficulty (in massproducing
tight RF filter and low-noise, front-end receiver amplifiers.)
In 1950, the channel bandwidth was cut in half to 60kHZ due to improved
technology.
By the mid 1960s, the channel bandwidth again was cut to 30 kHZ.
Thus, from WWII to the mid 1960s, the spectrum efficiency was improved only a
factor of 4 due to the technology advancements.
Also in 1950s and 1960s, automatic channel truncking was introduced
in IMTS(Improved Mobile Telephone Service.)
offering full duplex, auto-dial, auto-trunking
became saturated quickly
By 1976, has only twelve channels and could only serve 543
customers in New York City of 10 millions populations.
Cellular radiotelephone
Developed in 1960s by Bell Lab and others
 The basic idea is to reuse the channel frequency at a sufficient distance to
increase the spectrum efficiency.
But the technology was not available to implement until the late 1970s.
(mainly the microprocessor and DSP technologies.)
In 1983, AMPS (Advanced Mobile Phone System, IS-41) deployed by
Ameritech in Chicago.
40 MHz spectrum in 800 MHz band
666 channels (+ 166 channels), per Fig 1.2.
Each duplex channel occupies > 60 kHz (30+30) FDMA to maximize
capacity.
Two cellular providers in each market.

In late 1991, U.S. Digital Cellular (USDC, IS-54) was introduced.

to replace AMPS analog channels
3 times of capacity due to the use of digital modulation ( DQPSK),
speech coding, and TDMA technologies.
could further increase up to 6 times of capacity given the advancements of
DSP and speech coding technologies.
In mid 1990s, Code Division Multiple Access (CDMA, IS-95) was introduced
by Qualcomm.
based on spread spectrum technology.
supports 6-20 times of users in 1.25 MHz shared by all the channels.
 each associated with a unique code sequence.
operate at much smaller SNR (FdB)
1. Mobile Communications Principles
Each mobile uses a separate, temporary radio channel to talk to the cell site. The cell
site talks to many mobiles at once, using one channel per mobile. Channels use a pair of
frequencies for communication—one frequency, the forward link, for transmitting from the
cell site, and one frequency, the reverse link, for the cell site to receive calls from the users.
Radio energy dissipates over distance, so mobiles must stay near the base station to maintain
communications. The basic structure of mobile networks includes telephone systems and
radio services.
Where mobile radio service operates in a closed network and has no access to the
telephone system, mobile telephone service allows interconnection to the telephone network
(see Figure 1).

Figure 1: Basic Mobile Telephone Service Network

Early Mobile Telephone System Architecture

Traditional mobile service was structured similar to television broadcasting: One very
powerful transmitter located at the highest spot in an area would broadcast in a radius of up
to fifty kilometers. The cellular concept" structured the mobile telephone network in a
different way. Instead of using one powerful transmitter, many low-power transmitters were
placed throughout a coverage area. For example, by dividing a metropolitan region into one
hundred different areas (cells) with low-power transmitters using twelve conversations
(channels) each,

2/23
the system capacity theoretically could be increased from twelve conversations— or voice
channels using one powerful transmitter—to twelve hundred conversations (channels) using
one hundred low-power transmitters. Figure 2 shows a metropolitan area configured as a
traditional mobile telephone network with one high-power transmitter.

Figure 2: Early Mobile Telephone System Architecture

2. Mobile Telephone System Using the Cellular Concept

Interference problems caused by mobile units using the same channel in adjacent areas
proved that all channels could not be reused in every cell. Areas had to be skipped before the
same channel could be reused. Even though this affected the efficiency of the original
concept, frequency reuse was still a viable solution to the problems of mobile telephony
systems.

Engineers discovered that the interference effects were not due to the distance between areas,
but to the ratio of the distance between areas to the transmitter power (radius) of the areas.
By reducing the radius of an area by fifty percent, service providers could increase the
number of potential customers in an area fourfold. Systems based on areas with a one-
kilometer radius would have one hundred times more channels than systems with areas ten
kilometers in radius. Speculation led to the conclusion that by reducing the radius of areas to
a few hundred meters, millions of calls could be served.

The cellular concept employs variable low-power levels, which allows cells to be sized
according to the subscriber density and demand of a given area. As the population grows,
cells can be added to accommodate that growth. Frequencies used in one cell cluster can be
reused in other cells. Conversations can be handed off from cell to cell to maintain constant
phone service as the user moves between cells (see Figure 3).

3/23
 Figure 3: Mobile Telephone System Using a Cellular Architecture

The cellular radio equipment (base station) can communicate with mobiles as long as they
are within range. Radio energy dissipates over distance, so the mobiles must be within the
operating range of the base station. Like the early mobile radio system, the base station
communicates with mobiles via a channel. The channel is made of two frequencies, one for
transmitting to the base station and one to receive information from the base station.

3. Cellular System Architecture

Increases in demand and the poor quality of existing service led mobile service providers to
research ways to improve the quality of service and to support more users in their systems.
Because the amount of frequency spectrum available for mobile cellular use was limited,
efficient use of the required frequencies was needed for mobile cellular coverage. In modern
cellular telephony, rural and urban regions are divided into areas according to specific
provisioning guidelines. Deployment parameters, such as amount of cell-splitting and cell
sizes, are determined by engineers experienced in cellular system architecture.

Provisioning for each region is planned according to an engineering plan that includes cells,
clusters, frequency reuse, and handovers.

Cells
A cell is the basic geographic unit of a cellular system.

4/23
The term cellular comes from the honeycomb shape of the areas into which a coverage
region is divided. Cells are base stations transmitting over small geographic areas that are
represented as hexagons. Each cell size varies depending on the landscape. Because of
constraints imposed by natural terrain and man-made structures, the true shape of cells is not
a perfect hexagon.

Clusters
A cluster is a group of cells. No channels are reused within a cluster. Figure 4 illustrates a
seven-cell cluster.

Figure 4: A Seven-Cell Cluster

Frequency Reuse
Because only a small number of radio channel frequencies were available for mobile
systems, engineers had to find a way to reuse radio channels in order to carry more than one
conversation at a time. The solution the industry adopted was called frequency planning or
frequency reuse. Frequency reuse was implemented by restructuring the mobile telephone
system architecture into the cellular concept.

5/23
The concept of frequency reuse is based on assigning to each cell a group of radio channels
used within a small geographic area. Cells are assigned a group of channels that is
completely different from neighboring cells. The coverage area of cells are called the
footprint. This footprint is limited by a boundary so that the same group of channels can be
used in different cells that are far enough away from each other so that their frequencies do
not interfere (see Figure 5).

Figure 5: Frequency Reuse

Cells with the same number have the same set of frequencies. Here, because the number of
available frequencies is 7, the frequency reuse factor is 1/7. That is, each cell is using 1/7 of
available cellular channels.

Cell Splitting
Unfortunately, economic considerations made the concept of creating full systems with many
small areas impractical. To overcome this difficulty, system operators developed the idea of
cell splitting. As a service area becomes full of users, this approach is used to split a single
area into smaller ones. In this way, urban centers can be split into as many areas as necessary
in order to provide acceptable service levels in heavy-traffic regions, while larger, less
expensive cells can be used to cover remote rural regions (see Figure 6).

6/23
Figure 6: Cell Splitting

Handoff
The final obstacle in the development of the cellular network involved the problem created
when a mobile subscriber traveled from one cell to another during a call. As adjacent areas
do not use the same radio channels, a call must either be dropped or transferred from one
radio channel to another when a user crosses the line between adjacent cells. Because
dropping the call is unacceptable, the process of handoff was created. Handoff occurs when
the mobile telephone network automatically transfers a call from radio channel to radio
channel as a mobile crosses adjacent cells (see Figure 7).

7/23
 Figure 7: Handoff between Adjacent Cells

During a call, two parties are on one voice channel. When the mobile unit moves out of the
coverage area of a given cell site, the reception becomes weak. At this point, the cell site in
use requests a handoff. The system switches the call to a stronger-frequency channel in a new
site without interrupting the call or alerting the user. The call continues as long as the user is
talking, and the user does not notice the handoff at all.

4. North American Analog Cellular Systems

Originally devised in the late 1970S to early 1980S, analog systems have been revised
somewhat since that time and operate in the 800-MHz range. A group of government, telco,
and equipment manufacturers worked together as a committee to develop a set of rules
(protocols) that govern how cellular subscriber units (mobiles) communicate with the "cellular
system." System development takes into consideration many different, and often opposing,
requirements for the system, and often a compromise between conflicting requirements results.
Cellular development involves some basic topics:

1. frequency and channel assignments

8/23
2. type of radio modulation

3. maximum power levels

4. modulation parameters

5. messaging protocols

6. call-processing sequences

The Advanced Mobile Phone Service (AMPS)

AMPS was released in 1983 using the 800-MHz to 900-MHz frequency band and the 30 kHz
bandwidth for each channel as a fully automated mobile telephone service. It was the first
standardized cellular service in the world and is currently the most widely used standard for
cellular communications. Designed for use in cities, AMPS later expanded to rural areas. It
maximized the cellular concept of frequency reuse by reducing radio power output. The
AMPS telephones (or handsets) have the familiar telephone-style user interface and are
compatible with any AMPS base station. This makes mobility between service providers
(roaming) simpler for subscribers. Limitations associated with AMPS include:

1. low calling capacity

2. limited spectrum

3. no room for spectrum growth

4. poor data communications

5. minimal privacy

6. inadequate fraud protection

AMPS is used throughout the world and is particularly popular in the United States, South
America, China, and Australia. AMPS uses frequency modulation (FM) for radio
transmission. In the United States, transmissions from mobile to cell site use separate
frequencies from the base station to the mobile subscriber.

Narrowband Analog Mobile Phone Service (NAMPS)

Since analog cellular was developed, systems have been implemented extensively throughout
the world as first-generation cellular technology. In the second generation of analog cellular
systems, NAMPS was designed to solve the problem

9/23
 of low calling capacity. NAMPS is now operational in 35 U.S. and overseas markets and
NAMPS was introduced as an interim solution to capacity problems. NAMPS is a U.S.
cellular radio system that combines existing voice processing with digital signaling, tripling
the capacity of today's AMPS systems. The NAMPS concept uses frequency division to get
three channels in the AMPS 30-kHz single channel bandwidth. NAMPS provides three users
in an AMPS channel by dividing the 30-kHz AMPS bandwidth into three 10-KHZ channels.
This increases the possibility of interference because channel bandwidth is reduced.

5. Cellular System Components

The cellular system offers mobile and portable telephone stations the same service provided
fixed stations over conventional wired loops. It has the capacity to serve tens of thousands of
subscribers in a major metropolitan area. The cellular communications system consists of the
following four major components that work together to provide mobile service to subscribers
(see Figure 8):

1. public switched telephone network (PSTN)

2. mobile telephone switching office (MTSO)

3. cell site with antenna system

4. mobile subscriber unit (MSU)

10/23
Figure 8: Cellular System Components

PSTN
The PSTN is made up of local networks, the exchange area networks, and the long-haul
network that interconnect telephones and other communication devices on a worldwide basis.

Mobile Telephone Switching Office (MTSO)

The MTSO is the central office for mobile switching. It houses the mobile switching center
(MSC), field monitoring and relay stations for switching calls from cell sites to wireline
central offices (PSTN). In analog cellular networks, the MSC controls the system operation.
The MSC controls calls, tracks billing information, and locates cellular subscribers.

The Cell Site

The term cell site is used to refer to the physical location of radio equipment that provides
coverage within a cell. A list of hardware located at a cell site includes power sources,
interface equipment, radio frequency transmitters and receivers, and antenna systems.

11/23
 Mobile Subscriber Units (MSUs)
The mobile subscriber unit consists of a control unit and a transceiver that transmits and
receives radio transmissions to and from a cell site. Three types of MSUs are available:

1. the mobile telephone (typical transmit power is 4.0 watts)

2. the portable (typical transmit power is 0.6 watts)

3. the transportable (typical transmit power is 1.6 watts)

The mobile telephone is installed in the trunk of a car, and the handset is installed in a
convenient location to the driver. Portable and transportable telephones are hand-held and
can be used anywhere. The use of portable and transportable telephones is limited to the
charge life of the internal battery.

6. Digital Systems
As demand for mobile telephone service has increased, service providers found that basic
engineering assumptions borrowed from wireline (landline) networks did not hold true in
mobile systems. While the average landline phone call lasts at least ten minutes, mobile calls
usually run ninety seconds. Engineers who expected to assign fifty or more mobile phones to
the same radio channel found that by doing so they increased the probability that a user
would not get dial tone—this is known as call-blocking probability. As a consequence, the
early systems quickly became saturated, and the quality of service decreased rapidly.
The critical problem was capacity. The general characteristics of TDMA, GSM, PCS1900, and
CDMA promise to significantly increase the efficiency of cellular telephone systems to allow a
greater number of simultaneous conversations.
Figure 9 shows the components of a typical digital cellular system.

12/23
Figure 9: Digital Cellular System

The advantages of digital cellular technologies over analog cellular networks include
increased capacity and security. Technology options such as TDMA and CDMA offer more
channels in the same analog cellular bandwidth and encrypted voice and data. Because of the
enormous amount of money that service providers have invested in AMPS hardware and
software, providers look for a migration from AMPS to DAMPS by overlaying their existing
networks with TDMA architectures.

13/23
Table: AMPS/DAMPS Comparison
Analog Digital

Standard EIA–553 (AMPS) IS–54 (TDMA + AMPS

Spectrum 824 MHz to 891 MHz 824 MHz to 891 MHz

Channel Bandwidth 30 kHz 30 kHz

Channels 21 CC / 395 VC 21 CC / 395 VC

Conversations per 1 3 or 6
Channel

Subscriber Capacity 40 to 50 125 to 300

Conversations per cell Conversations per cell

TX / RCV Type Continuous Time shared bursts

Carrier Type Constant phase Constant frequency

Variable frequency Variable phase

Mobile/Base Relationship Mobile slaved to base Authority shared cooperatively

Privacy Poor Better—easily scrambled

Noise Immunity Poor High

Fraud Detection ESN plus optional password (PIN) ESN plus optional password (PIN)

14/23
 Time Division Multiple Access (TDMA)
North American digital cellular (NADC) is called DAMPS and TDMA. Because AMPS
preceded digital cellular systems, DAMPS uses the same setup protocols as analog AMPS.
TDMA has the following characteristics:

1. IS–54 standard specifies traffic on digital voice channels

2. Initial implementation triples the calling capacity of AMPS systems

3. Capacity improvements of 6 to 15 times that of AMPS are possible

4. Uses many blocks of spectrum in 800 MHz and 1900 MHz

5. All transmissions are digital

6. TDMA/FDMA application 7. 3 callers per radio carrier (6 callers on half rate later), providing
three times the AMPS capacity

TDMA is one of several technologies used in wireless communications. TDMA provides

each call with time slots so that several calls can occupy one bandwidth. Each caller is
assigned a specific time slot. In some cellular systems, digital packets of information are sent
during each time slot and reassembled by the receiving equipment into the original voice
components. TDMA uses the same frequency band and channel allocations as AMPS. Like
NAMPS, TDMA provides three to six time channels in the same bandwidth as a single
AMPS channel.
Unlike NAMPS, digital systems have the means to compress the spectrum used to transmit
voice information by compressing idle time and redundancy of normal speech. TDMA is the
digital standard and has 30-kHz bandwidth. Using digital voice encoders, TDMA is able to
use up to six channels in the same bandwidth where AMPS uses one channel.

Extended Time Division Multiple Access (E– TDMA)

The extended TDMA (E–TDMA) standard claims a capacity of fifteen times that of analog
cellular systems. This capacity is achieved by compressing quiet time during conversations.
E–TDMA divides the finite number of cellular frequencies into more time slots than TDMA.
This allows the system to support more simultaneous cellular calls.

Fixed Wireless Access (FWA)

Fixed wireless access (FWA) is a radio-based local exchange service in which telephone
service is provided by common carriers (see Figure 10). It is primarily a

15/23
rural application—that is, it reduces the cost of conventional wireline. FWA extends
telephone service to rural areas by replacing a wireline local loop with radio
communications. Other labels for wireless access include fixed loop, fixed radio access,
wireless telephony, radio loop, fixed wireless, radio access, and Ionica. FWA systems
employ TDMA or CDMA access technologies.

Figure 10: Fixed Wireless Access

Personal Communications Services (PCS)

The future of telecommunications includes personal communications services. PCS at 1900
MHz (PCS1900) is the North American implementation of DCS1800 (Global System for
Mobile communications, or GSM). Trial networks were operational in the United States by
1993, and in 1994 the Federal Communications Commission (FCC) began spectrum auctions.
As of 1995, the FCC auctioned commercial licenses. In the PCS frequency spectrum the
operator's authorized frequency block contains a definite number of channels.
The frequency plan assigns specific channels to specific cells, following a reuse pattern which
restarts with each nth cell. The uplink and downlink bands are paired mirror images. As with
AMPS, a channel number implies one uplink and one downlink frequency: e.g., Channel 512 =
1850.2 MHz uplink paired with 1930.2 MHz downlink.

16/23
 Code Division Multiple Access (CDMA)
Code division multiple access (CDMA) is a digital air interface standard, claiming eight to
fifteen times the capacity of analog. It employs a commercial adaptation of military spread-
spectrum single-sideband technology. Based on spread spectrum theory, it is essentially the
same as wireline service—the primary difference is that access to the local exchange carrier
(LEC) is provided via wireless phone. Because users are isolated by code, they can share the
same carrier frequency, eliminating the frequency reuse problem encountered in AMPS and
DAMPS. Every CDMA cell site can use the same 1.25 MHz band, so with respect to clusters,
n = 1. This greatly simplifies frequency planning in a fully CDMA environment.

CDMA is an interference limited system. Unlike AMPS/TDMA, CDMA has a soft capacity
limit; however, each user is a noise source on the shared channel and the noise contributed by
users accumulates. This creates a practical limit to how many users a system will sustain.
Mobiles that transmit excessive power increase interference to other mobiles. For CDMA,
precise power control of mobiles is critical in maximizing the system's capacity and
increasing battery life of the mobiles. The goal is to keep each mobile at the absolute
minimum power level that is necessary to ensure acceptable service quality. Ideally, the
power received at the base station from each mobile should be the same (minimum signal to
interference).

Self-Test
1. Interference effects in cellular systems are a result of .

a. the distance between areas

b. the power of the transmitters

c. the ratio of the distance between areas to the transmitter power of the areas

d. the height of the antennas

2. Larger cells are more useful in .

a. densely populated urban areas

b. rural areas

c. lightly populated urban areas

d. mountainous areas

17/23
3. The most widely used standard for cellular communications is .

a. the advanced mobile phone service (AMPS)

b. the mobile subscriber unit (MSU)

c. the mobile telephone switching office

d. code division multiple access (CDMA)

4. How many conversations per channel can TDMA digital cellular carry at once?

a. 1

b. 2

c. 3

d. 10

5. Which of the following is not a limitation of AMPS?

a. low calling capacity

b. poor privacy protection

c. Limited spectrum

d. wide coverage area

6. Digital cellular technologies offer increased capacity and security .

a. true

b. false

7. TDMA, a digital air interface standard, has twice the capacity of analog.

a. true

b. false

8. Cells are always hexagonal in shape.

a. true

b. false

18/23
9. Frequency reuse was maximized by increasing the size of cells.

a. true

b. false

10. Fixed wireless access is primarily a rural application.

a. true

b. false

Correct Answers
1. Interference effects in cellular systems are a result of .

a. the distance between areas

b. the power of the transmitters

c. the ratio of the distance between areas to the transmitter power of the areas

d. the height of the antennas See Topic 2

2. Larger cells are more useful in .

a. densely populated urban areas

b. rural areas

c. lightly populated urban areas

d. mountainous areas See Topic 3

3. The most widely used standard for cellular communications is .

a. the advanced mobile phone service (AMPS)

b. the mobile subscriber unit (MSU)

c. the mobile telephone switching office

d. code division multiple access (CDMA)

19/23
 See Topic 4

4. How many conversations per channel can TDMA digital cellular carry at once?

a. 1

b. 2

c. 3

d. 10

See Topic 6

5. Which of the following is not a limitation of AMPS?

a. low calling capacity

b. poor privacy protection

c. limited spectrum

d. wide coverage area

See Topic 4

6. Digital cellular technologies offer increased capacity and security.

a. true

b. false

See Topic 6

7. TDMA, a digital air interface standard, has twice the capacity of analog.

a. true

b. false

See Topic 6

8. Cells are always hexagonal in shape.

a. true

b. false

20/23
 See Topic 3

9. Frequency reuse was maximized by increasing the size of cells.

a. true

b. false

See Topic 3

10. Fixed wireless access is primarily a rural application.

a. true

b. false

See Topic 6

Acronym Guide
AMPS
advanced mobile phone service; another acronym for analog cellular radio

BTS
base transceiver station; used to transmit radio frequency over the air interface

CDMA
code division multiple access; a form of digital cellular phone service that is a spread
spectrum technology that assigns a code to all speech bits, sends scrambled transmission of
the encoded speech over the air, and reassembles the speech to its original format

DAMPS
digital advanced mobile phone service; a term for digital cellular radio in North America

DCS
digital cellular system

ESN
electronic serial number; an identity signal that is sent from the mobile to the MSC during a
brief registration transmission

ETDMA
extended TDMA; developed to provide fifteen times the capacity over analog systems by
compressing quiet time during conversations

21/23
FCC
Federal Communications Commission; the government agency responsible for regulating
telecommunications in the United Sates

FCCH
frequency control channel

FDMA
frequency division multiple access; used to separate multiple transmissions over a finite
frequency allocation; refers to the method of allocating a discrete amount of frequency
bandwidth to each user to permit many simultaneous conversations

FM
frequency modulation; a modulation technique in which the carrier frequency is shifted by an
amount proportional to the value of the modulating signal

FRA
fixed radio access

GSM
global system for mobile communications; standard digital cellular phone service in Europe
and Japan; to ensure interpretability between countries, standards address much of the
network wireless infrastructure, including radio interfaces, switching, signaling, and
intelligent networks

Hz
hertz; a measurement of electromagnetic energy, equivalent to one wave or cycle per second

kHz
kilohertz; thousands of hertz.

MHz
megahertz; millions of hertz.

MS or MSU
mobile station unit; handset carried by the subscriber

MSC
mobile services switching center; a switch that provides services and coordination between
mobile users in a network and external networks

MTSO
mobile telephone switching office; the central office for the mobile switch, which houses the
field monitoring and relay stations for switching calls from cell sites to wireline central
offices (PSTN)

22/23
MTX
mobile telephone exchange

NADC
North American digital cellular (also called United States digital cellular, or USDC); a time
division multiple access (TDMA) system that provides three to six times the capacity of
AMPS

NAMPS
narrowband advanced mobile phone service; NAMPS was introduced as an interim solution
to capacity problems; NAMPS provides three times the AMPS capacity to extend the
usefulness of analog systems

PCS
personal communications service; a lower-powered, higher-frequency competitive
technology that incorporates wireline and wireless networks and provides personalized
features

PSTN
public switched telephone network; a PSTN is made of local networks, the exchange area
networks, and the long-haul network that interconnect telephones and other communication
devices on a worldwide basis

RF
radio frequency; electromagnetic waves operating between 10 kHz and 3 MHz propagated
without guide (wire or cable) in free space

SIM
subscriber identity module; a smartcard, which is inserted into a mobile phone to get it going

SNSE
supernode size enhanced

TDMA

time division multiple access; used to separate multiple conversation transmissions over a
finite frequency allocation of through-the-air bandwidth; used to allocate a discrete amount
of frequency bandwidth to each user; to permit many simultaneous conversations, each caller
is assigned a specific timeslot for transmission

23/23