Chiller Midea PDF

Air-cooled screw chiller technical manual (PLC series) MCAC-CTSM-2013-01
Air cooled screw chiller

Technical service manual
(LSBLGW***/C
All empires fall, you just have to know where to push. 1

Contents
I. Product ......................................................................................................................... 3
1. Nomenclature ...........................................................................................................................3
2. Product Line Up .......................................................................................................................3
3. External Appearance………………………………………………………………………………… 4
4. Features…………………………………………………………………………………………………5
5. Specification .............................................................................................................................8
6. Operating Range ....................................................................................................................10
7. Outline Dimension .................................................................................................................11
8. Water Flow – Water Drop Pressure Curve ...........................................................................13
II. Installation.................................................................................................................. 15
1. Installation Dimensions& Vibration Isolators………………………………………………… 15
2. Installation Foundation ..........................................................................................................20
3. Installation Spaces.................................................................................................................20
4. Installation of Water Pipeline System ..................................................................................21
III. Electrical Data ............................................................................................................ 26
1. Field Wiring.............................................................................................................................26
2. Electric parameter table ........................................................................................................30
3. Control Flow Chart .................................................................................................................31
4. Control Screen Operation .....................................................................................................33
5. Control Screen Menu Structure ............................................................................................48
6. Introduction of Major Electric Components.........................................................................49
IV. Maintenance and Commissioning ............................................................................ 51
1. Commissioning ......................................................................................................................51
2. Maintenance ...........................................................................................................................61
V. Control Logic ............................................................................................................. 77
1. Start (Stop) Logic ...................................................................................................................77
2. Energy Adjustment Logic ......................................................................................................83
3. Fan Control Logic ..................................................................................................................86
4. Oil heater control Logic .........................................................................................................86
5. EXV operation& wiring ..........................................................................................................87
Appendix 1: R134a saturation temperature - pressure corresponding tables………90
Appendix 2: System working principle map………………………………………………91
Appendix 3: Capacity table…………………………………………………………………...95
Appendix 4: Electrical circuit principle reference map…………………………….….. 99
2
I. Product
1. Nomenclature
LS B LG W 380 /C
C: R134a; omit for R22
380: nominal cooling capability (kW)
W: air-cooled condenser
LG: Screw compressor
B: semi-hermetic compressor
LS: water chiller
2. Product Line Up
Model Power Supply Cooling Capacity (kW) Quantity of Compressor Quantity of Fan
LSBLGW380/C 380V/3Ph/50Hz 376 1 6
LSBLGW500/C 380V/3Ph/50Hz 496 1 8
LSBLGW600/C 380V/3Ph/50Hz 594 1 10
LSBLGW720/C 380V/3Ph/50Hz 720 1 10
LSBLGW880/C 380V/3Ph/50Hz 880 2 14
LSBLGW1000/C 380V/3Ph/50Hz 996 2 16
LSBLGW1200/C 380V/3Ph/50Hz 1203 2 16
LSBLGW1420/C 380V/3Ph/50Hz 1419 2 20
3
3. External Appearance
LSBLGW380/C module LSBLGW500/C module
LSBLGW600/C LSBLGW720/C module LSBLGW880/C module
LSBLGW1000/C LSBLGW1200/C module
LSBLGW1420/C module
4
4. Features
Environmental care
 R134a refrigerant
Refrigerant of the HFC group with zero ozone depletion potential.
It is environmentally safe and does not have a phase-out date.
Economical Operation Cost

 Extremely high full load and partial load energy efficiency. New twin-rotor screw compressor
equipped with a high-efficiency motor and a variable capacity valve that can adjust the capacity of
25%, 50%, 75% and 100% in 4 stages (Stepless control as an option) and permits exact matching
of the cooling capacity to the actual load.
 Electronic expansion device permits the operation at a lower condensing pressure and improve the
utilization of the evaporator heat exchange surface (superheat control).
 Economizer system with electronic expansion device for increases the cooling capacity. Automatic
scheduling of the Chiller's compressors allows the chiller to match the fluctuating cooling load and
conserve energy with each unit running at its peak efficiency.
Lower operating noise

 The twin-screw compressor adopts the strong points of gapless-loss, high-efficiency cubage,
low-noise, few easy workout parts. Double-wall structure not only compensates the pressure, but
also significantly reduces the noise. Cast iron structure of the compressor casing and oil separator
can reduce the noise significantly.
5
 Low-noise fans, made of a composite material are now even quieter and do not generate
intrusive low-frequency noise. Rigid fan mounting avoids start-up noise.
Multiple direct drive dynamically balanced propeller fans operate at low tip speeds for maximum
efficiency and minimum noise and vibration. A heavy-gauge vinyl-coated fan guard protects each
fan.
Outstanding reliability
 Full factory testing of all the units ensures a trouble free start-up. Extensive test makes certain that
each safety and operating control is properly adjusted, and operates correctly. The unit has passed
full factory test before being delivered to ensure the reliable working on the site.
 Transport simulation test in the laboratory on a vibrating table.
Simple Structure, Easy Installation
 The unit can be placed in service after being connected with power supply and water supply during
field installation .Standard flange connection and wire mesh to the electrical panel make the
installation easy and simple.
State of Technique, Accuracy Control
 The sensors related to control and other assemblies are equipped by factory and strictly tested.
 Intelligent control：The unit is controlled by micro-controller(PLC) and has the automatic control
functions of fault diagnosis, energy management and anti-freezing monitoring, which ensures the
high-efficiency operation of the unit, and more convenient in use. The unit with RS485 open protocol
communication interface. BMS compatible. The startup and shutdown of each unit is controlled by
the host computer, reducing the running cost to the lowest.
 Complete and safe control system: All electrically control elements are designed and selected with
stable quality and reliable function; The unit designed with multiple security measures ensure the
safe and reliable running witch including high and low pressure protection, oil pressure difference
6
protection, anti-freezing protection, water flow protection, power protection, overload protection
etc.
Modular design, Flexible combination
 The units adopt modular design, which can makes more unit connect together. The unit can
combine 8 modules. Cooling capacity can be within 360kW-7200kW, meanwhile every separate
module can operate as master, also each module can be a slave unit with modules combination,
more convenient for design and installation.
7
5. Specification
Single Compressor:
Unit Model LSBLGCW380/C LSBLGCW500/C LSBLGW600/C LSBLGW720/C

Cooling capacity kW 376 496 594 720
Power supply 380V/3P/50Hz
Rated power
consumption kW 124 159 187 234
Type Semi- hermetic, twin screw compressor
Compressor
Quantity 1 1 1 1
Energy adjustable range% 25%,50%,75%,100% 4-step ( 50%~100% stepless as option)
Refrigerant Type R134a
Type M shape Heat exchanger, High efficient exchanger tube + aluminum fins
Air Side Fans Quantity 6 8 10 10
Heat-exchanger
Air Volume（m3/h） 23000×6 23000×8 23000×10 23000×10
Motor input（kW） 2.8×6 2.8×8 2.8×10 2.8×10
Type Shell-and-tube heat-exchanger
Water Volume
Water Side （m3/h） 65.4 86 103.2 123.8
Heat-exchanger Water pressure
drop（kpa） 39 54 56 58
Inlet/outlet Pipe
diameter（mm） DN125 DN125 DN125 DN150
2.
Water side fouling factor (m ℃/kW) 0.086
Length（mm） 3810 4680 5880 5880
Dimension（mm） width（mm） 2280 2280 2280 2280
height（mm） 2370 2370 2370 2370
Shipping weight（kg） 3320 4330 5000 5500
Running weight（kg） 3520 4530 5200 5700
Note:
1) Nominal cooling capacities are based on the following conditions:
Chilled water inlet/outlet temp: 12℃/7℃; Outdoor temp (DB/WB):35℃/24℃.
2) The applicable ambient temperature range of R134a air-cooled screw units is 15℃ ~ 43℃。
8
Dual Compressors:
Unit Model LSBLGCW880/C LSBLGCW1000/C LSBLGW1200/C LSBLGW1420/C

Cooling
capacity kW 880 996 1203 1419
Power supply 380V/3P/50Hz
Rated power
consumption kW 285 318 381 466
Type Semi- hermetic, twin screw compressor
Compressor
Quantity 2 2 2 2
Energy adjustable range% 12.5%、25%、37.5%、50%、62.5%、75%、87.5%、100%
Refrigerant Type R134a
Type M shape Heat exchanger, High efficient exchanger tube + aluminum fins
Air Side Fans Quantity 14 16 16 20

Heat-exchanger
Air Volume（m3/h） 23000×14 23000×16 23000×16 23000×20
Motor input（kW） 2.8×14 2.8×16 2.8×16 2.8×20
Type Shell-and-tube heat-exchanger
Water Volume（m3/h） 151.4 172 206.4 244.2
Water Side
Water pressure drop
Heat-exchanger
（kpa） 70 75 71 69
Inlet/outlet Pipe
diameter（mm） DN150 DN150 DN200 DN200
2.
Water side fouling factor (m ℃/kW) 0.086
Length（mm） 8800 9640 9640 11700
Dimension
（mm） width（mm） 2280 2280 2280 2280
height（mm） 2430 2430 2430 2430
Shipping weight（kg） 7750 8900 9100 11100
Running weight（kg） 8050 9200 9400 11400
Note:
1) Nominal cooling capacities are based on the following conditions:
Chilled water inlet/outlet temp: 12℃/7℃; Outdoor temp (DB/WB):35℃/24℃.
2) The applicable ambient temperature range of R134a air-cooled screw units is 15℃ ~ 43℃。
9
6. Operating Range
Content Running range

Ambient Temp. 15℃～43℃(T1)
Leaving water Temp. 5℃～15℃

Water flow volume Rating flow volume±20%
Max inlet/outlet water Temp. difference 8℃
2.
Fouling factor (m ℃/kW) 0.086
Voltage tolerance Rating Voltage±10%
Phase tolerance ±2％
Power supply frequency Rating frequency±2%
Evaporator max working pressure on water side 1.0MPa
Compressor max. start count 4 times/h
High corrosive environment and high
Environment quality
humidity should be avoided.
The height of water drainage should not be
Drainage system
higher than the base of the unit on the spot
Storage and transport temperature -25℃～55℃
In + 40℃ does not exceed 50%, + 25℃ no
RH(relative air humidity)
more than 90%
Applicable altitude range： No more than 1000m
10
7. Outline Dimension
(1) LSBLGW380/C unit (mm)
11
12
8. Water Flow – Water Drop Pressure Curve

Balance the chilled water flow through the evaporator. The flow rates must fall between the
minimum and maximum values shown in the below table. Flow rates below the minimum values shown
will result in laminar flow which will reduce efficiency, cause erratic operation of the electronic expansion
valve and could cause low temperature cutouts. On the other hand, flow rates exceeding the maximum
values shown can cause erosion on the evaporator water connections and tubes, even piping breaking.
Variable chilled water flow through the evaporator while the compressor(s) are operating is not
recommended. The chiller control set points are based upon a constant flow and variable temperature.
Unit Model MIN. FLOW RATE MAX. FLOW RATE

3 3
SIZE m /h GPM m /h GPM
LSBLGW380/C 46 201 85 374
LSBLGW500/C 60 265 112 492
LSBLGW600/C 72 318 134 590
LSBLGW720/C 87 381 161 708
LSBLGW880/C 106 466 197 866
LSBLGW1000/C 120 530 224 984
LSBLGW1200/C 144 636 268 1181
LSBLGW1420/C 171 752 317 1397
13
14
II. Installation
1. Installation Dimensions & Vibration Isolators

Vibration isolators are recommended for all roof mounted installations or wherever vibration
transmission is a consideration.
Neoprene Isolation is optional, it is recommended for normal installations and provides good
performance in most applications for the least cost.
Spring isolators are level adjustable, spring and cage type isolators, mounted under the unit base
rails. Deflection may vary slightly by application.
Isolator model Midea code Brand
Spring isolator MHD-850 202502301043 Mei Huan (Yan Cheng City)
Spring isolator MHD-1050 202502301044 Mei Huan (Yan Cheng City)
The housing of MHD series with aluminum-magnesium alloy

material could prevent the vibration isolator from rustiness forever
and enlarge the use life. The structure
also has new improvement with an
anti-side-force function for better
stability and safety of unit. It can be
freely adjusted as per balancing
situation of unit to guarantee its work
under all situations.
Technical Date of MHD
MODEL LOAD LOAD DEFLECTION VERTICAL

(kg) (N) (mm) (kg/mm)
MHD-850 850 8330 25 34.00
MHD-1050 1050 10290 25 42.00
OUTER SIZE (mm)

MODEL
A B C ΦE F H S1 S2 ΦD
MHD-850 165 200 13 12.5 147 165 M12*25 M20*60 104
MHD-1050 165 200 13 12.5 147 165 M12*25 M20*60 104
15
C ontrol box
F ound ation
U nit bo ttom
F o und ation
b olt M 14
Weight to be supported by spring isolator(kg)

Model
A B C D
LSBLGW380/C 864 896 864 896
C ontrol b ox
F oundation
U nit bottom
F oundation
bolt M 14

Model
A B C D E F
LSBLGW500/C 614 837 814 614 837 814
16
C o n tro l b o x
F o u n d a tio n
U n it b o tto m
F o u n d a tio n
b o lt M 1 4

Model
A B C D E F
LSBLGW600/C 742 934 921 742 934 921
C o n tro l b o x
F o u n d a tio n
U n it b o tto m
F o u n d a tio n
b o lt M 1 4

Model
A B C D E F G H
LSBLGW720/C 647 725 760 718 647 725 760 718
17
Control box
Unit bottom
Foundation
Foundation bolt M14
Weight to be supported by spring isolator（kg）

Model
A B C D E F G H I J
LSBLGW880/C 781 912 915 715 701 781 912 915 715 701
Control box
Unit bottom
Foundation
Foundation bolt M14

Model
A B C D E F G H I J K L
LSBLGW1000/C 701 887 892 707 706 707 701 887 892 707 706 707
18
Control box
Unit bottom
Foundation
Foundation bolt M14

Model
A B C D E F G H I J K L
LSBLGW1200/C 731 912 905 721 716 715 731 912 905 721 716 715
Control box
Unit bottom
Foundation
Foundation bolt M14

Model
A B C D E F G H I J K L M N
LSBLGW1420/C 717 925 954 936 724 722 722 717 925 954 936 724 722 722
19
2. Installation Foundation
1) The installation foundation shall be designed by professionals according to the site conditions.
2) The installation foundation of the unit must be of a cement or steel structure, and shall bear the
operating weight of the machine, and this face must be horizontal.
3) Please refer to the Diagram for Installation Foundation of Unit, place the steel plate and
anti-vibration bush on the foundation accurately, and execute secondary grouting after
installing the unit and foundation bolts together. The foundation bolts are generally 60 mm
higher than the installation surface .
Bolt
Unit Base (Channel Steel) Installation
Surface Nut
Drain Groove
Washer
Cement Mortar Link Kit
(Secondary Grouting) Anti-vibration
Bush
Steel Plate
Concrete
4) T If the unit will be installed on the top of the building which vibration level should be restricted.
It is recommended to use spring isolators as absorber, please refer to following diagram:
Unit Bottom
Spring Shock
Absorber
Foundation
3. Installation Spaces
1) Reserve the spaces required for unit installation, operation and maintenance.
2) The installation place of the unit shall be free from the effects of fire, inflammables, corrosive
gas or waste gas as much as possible; the ventilation space shall be reserved there; proper
measures shall be taken to reduce noise and vibration whenever possible.
3) When the units are installed on the horizontal plane without obstacles, the longitudinal distance
between the units shall be kept above 1m, the transverse distance between the units shall be
kept above 1.8 m, and such distances shall be as large as possible; if there are obstacles at
both sides of the unit, the distance between the unit and obstacles shall be kept above 1.8 m; if
there are obstacles above the unit, the distance between the unit and obstacles shall be kept
above 2.5 m.
4) The removable post for compressor service access must not be blocked at either side of the unit.
20
5) There must be no obstruction under the fans.
4. Installation of Water Pipeline System

Due to the variety of piping practices, it is advisable to follow the recommendations of local
authorities. The installation and insulation of the water pipelines of the air conditioning system shall
be designed and guided by design professionals, and confirm to the corresponding provisions of the
HVAC installation specifications.
Basically, the piping should be designed with a minimum number of bends and changes in elevation
to keep system cost down and performance up.
Single unit:
21
Parallel connection of units:
1) The water inlet pipeline and drain pipeline shall be connected according to the requirements of
markings on the unit. Generally, the refrigerant pipe side of the evaporator is the chilled water
outlet side.
2) The chilled water pipeline system must be provided with the soft connection, thermometer,
pressure gauge, water filter, electronic scale remover, check valve, target flow controller,
discharge valve, drain valve, stop valve, expansion tank, etc.
3) The water system must be fitted with the water pump with appropriate displacement and head,
so as to ensure normal water supply to the unit. The soft connection shall be used between the
water pump, unit and water system pipelines, and the bracket shall be provided to avoid stress
on the unit. Welding work for installation shall avoid damage to the unit.
(1) Determination of water pump flow:
Flow (m3/h) = (1.1 ~ 1.2) * Unit Cooling Capacity (kW)/5.8
(2) Determination of water pump head:
Head (m) = (Unit Resistance (see product parameters) + Resistance at Maximum End of
Pressure Drop (see product parameters) + Pipeline Resistance (length of the least favorable
loop pipe * 0.05) + Local Resistance (length of the least favorable loop pipe * 0.05 * 0.5)) * (1.1
~ 1.2)
4) The flow switch must be arranged on the drain pipe of the evaporator. The flow switch shall be
interlocked with the input contact in the control cabinet. Its installation requirements are as
22
follows:
(1) The flow switch shall be installed on the pipe vertically.
(2) The straight pipe section at each side of the flow switch shall have a length that is at least 5
times the pipe diameter; do not install it near the elbow, orifice plate or valve.
The straight pipe section

The installation of the flow for installation of the flow
switch is unsatisfied. switch is satisfied.
(3) The direction of the arrow on the flow switch must be consistent with the direction of water
flow.
(4) In order to prevent vibration of the flow switch, remove all air in the water system.
(5) Adjust the flow switch to keep it in open state when the flow is lower than the minimum flow
(the minimum flow is 70% of the design flow). When the water flow is satisfied, the flow
switch shall keep in closed state.
5) The water filter must be installed before the water inlet pipeline of the unit, which shall be
provided with a 25-mesh screen. This will aid in preventing foreign material from entering and
decreasing the performance of the evaporator.
23
Install the filter at

the evaporator inlet.
6) A strainer should be placed for enough upstream to prevent cavitation at the pump inlet (consult
pump manufacturer for recommendations). The use of a strainer will prolong pump life and help
maintain high system performance levels
7) The flushing and insulation of the water pipelines shall be carried out before it is connected with
the unit, so as to prevent dirt from damaging the unit.
8) The design water pressure of the water chamber is 1.0Mpa. Use of the water chamber shall be
not exceeding this pressure in order to avoid damaging the evaporator.
9) The expansion tank shall be installed 1~1.5m higher than the system, and its capacity accounts
about 1/10 of the water amount in the whole system.
10) The drain connection is arranged on the evaporator cylinder. The drain outlet has been
equipped with a 1/2’’ plug.
11) The auto discharge air valve is arranged between the high point of the pipeline and the
expansion tank.
12) The thermometer and pressure gauge are arranged on the straight pipe sections of the water
inlet pipeline and drain pipeline, and their installation places shall be far away from the elbows.
The pressure gauge installed shall be vertical to the water pipe, and the installation of the
thermometer shall ensure that its temperature probe can be inserted into the water pipe
directly.
13) Each low point shall be fitted with a drain connection so as to drain the remaining water in the
system. Before operating the unit, connect the stop valves to the drain pipeline, respectively
near the water inlet connection and drain connection. The by-pass pipeline shall be provided
between the water inlet pipe and drain pipe of the evaporator, convenient for cleaning and
maintenance. Use of flexible connections can reduce vibration transfer.
14) The chilled water pipeline and expansion tank shall be subjected to insulation treatment, and
the maintenance and operation part shall be reserved on the valve connections.
15) After the air-tightness test is carried out, and the insulation layer is applied on the pipeline, so
as to avoid heat transfer and surface condensation; the insulation layer shall be covered by
moisture-proof seal.
16) Any water piping to the unit must be protected to prevent freezing. There are reserved
terminals for the auxiliary electrical heater. Logic in PLC will transmit ON/OFF signal by
checking the leaving evaporator water temperature.
Note: The unit only supply ON/OFF signal, but not the 220V power. If a separate disconnect is
24
used for the 220V supply to the cooler heating cable, it should be clearly marked so that it is not
accidentally shut off during cold seasons
17) If the unit is used as a replacement chiller on a previously existing piping system, the system
should be thoroughly flushed prior to unit installation and then regular chilled water analysis
and chemical water treatment is recommended immediately at equipment start-up.
18) Power on the chilled water pump, and inspect its rotation direction. The correct rotation
direction shall be clockwise; if not, re-inspect the wiring of the pump.
19) Start the chilled water pump to circulate water flow. Inspect the water pipelines for water
leakage and dripping.
20) Commission the chilled water pump. Observe whether the water pressure is stable. Observe
the pressure gauges at the pump inlet and outlet, and the readings of the pressure gauges and
the pressure difference between the inlet and outlet change slightly when the water pressure is
stable. Observe whether the operating current of the pump is within the range of rated
operating current; inspect whether the resistance of the system is too large if the difference
between the operating current and rated value is too big; eliminate the system failures until the
actual operating current is satisfied.
21) Inspect whether the water replenishing device for the expansion tank is smooth, and the auto
discharge air valve in the water system enables auto discharge. If the discharge air valve is a
manual type, open the discharge valve of the chilled water pipeline to discharge all air in the
pipeline.
22) Adjust the flow and inspect whether the water pressure drop of the evaporator meets the
requirement of the unit’s normal operation. The pressure at the chilled water inlet and outlet of
the unit shall be kept at least 0.2MPa.
23) The total water quantity in the system should be sufficient to prevent frequent “on-off” cycling. A
reasonable minimum quantity would allow for a complete water system turnover in not less
than 15 minutes.
25
III. Electrical Data
1. Field Wiring
WARNING: In order to prevent any accident of injury and death during the site wiring, the power
supply shall be cut off before the line is connected to the unit.
Wiring must comply with all applicable codes and ordinances. Warranty is voided if wiring is not in
accordance with specifications. An open fuse indicates a short, ground, or overload. Before
replacing a fuse or restarting a compressor or fan motor, the trouble must be found and corrected.
(1) Copper wire is required for all supply lines in field connection to avoid corrosion and overheat at
the connection of terminals. The lines and control cables shall be separately paved and
equipped with protective pipes to avoid intervention of supply line in control cable.
(2) Power section: It is required to connect the power supply cable to the control cabinet of the unit,
when it arrives at the jobsite. The power supply cable is connected to the terminals of L1, L2, L3,
N and PE and the terminals need to be fixed again after 24h running (the minimum allowed
time). Please seal the entering wiring hole after users installed the main power wires, in order to
avoid the dust entering into electric control cabinet.
Caution: it is suggested that to use appropriate tools to make sure there is a enough height to
install the main power wires if the basement is higher than 200 mm.
N
communication interface
Cooling run output
PE
Remote Start
Remote Stop
Flow switch
L3 L1
Alarm
Pump
Indication
Multi-units
L2
[Diagram for External Wiring of LSBLGW380/C LSBLGW500/C LSBLGW600/C LSBLGW720/C Unit]
26
water flow switch

Remote start
Remote stop
Water pump
mode indication
communication
2# Alarm
1# Alarm
Multiple
[Diagram for External Wiring of LSBLGW880/C LSBLGW1000/C

LSBLGW1200/C LSBLGW1420/C Unit]
(3) Breaking isolation switches should be added between the power cord of users and the unit. The
capacities of the breaking isolation switches recommended are as follows.
BVR：Copper core PVC insulated soft wire

Nominal
Domestic Conductor Insulator section
UL model Note
model material material area
(MM ²)
BVR70 Cu PVC 70 2/0
BVR95 Cu PVC 95 4/0
BVR120 Cu PVC 120 250
The
BVR150 Cu PVC 150 300
electric
BVR185 Cu PVC 185 400 cable
BVR240 Cu PVC 240 500 must be
BVR300 Cu PVC 300 600 copper
BVR400 Cu PVC 400 800 core.
27
Recommended
Model Recommended Cable Note
breaker
LSBLGW380/C BVR120*4+BVR70*1 330A
LSBLGW500/C BVR240*4+BVR120*1 500A

The electric cable must be
LSBLGW600/C BVR240*4+BVR120*1 500A copper core. If units are
used in high temperature
LSBLGW720/C 2*(BVR185*4+BVR120*1) 630A
conditions, the breaker
(BVR185*4+BVR120*1)+ needs larger capacity.
LSBLGW880/C 830A
(BVR240*4+BVR120*1)
LSBLGW1000/C 2* (BVR240*4+BVR120*1) 1000A

(BVR240*4+BVR120*1)+
LSBLGW1200/C 1000A
(BVR300*4+BVR150*1)
LSBLGW1420/C 2* (BVR400*4+BVR240*1) 1260A
(4) Attention: refrigerant selection: the previous software settings are replaced by the current
hardware settings to avoid the possibility of improper operation of the software leading to
wrongly selected refrigerant and damage to the unit.
(5) Short circuit 1X：35/1X：36 on the wiring terminal 1X in the cabinet and set R22 refrigerant for
the unit, or, R134a is used for the unit.
(6) In order to avoid wrong control in field connection, the liquid control circuit (24 V) shall not be in
the same conduit with the lead wire of the voltage higher than 24 V.
(7) The control circuits of various units are all 220 V, and for the wiring ways of the control circuits,
please refer to the wiring diagrams supplied along with the units.
(8) A unit consists of master compressor and slave compressor communicating via shield wire
protected by sleeve and separated from supply line.
(9) The control output cable to be connected on site shall be AC250V-1mm2, and 0.75mm2 shield
wire (24 V) shall be used for control signal line.
(10) Attentions: Read the electrical wiring principle diagram and connect the wires strictly according
to the wiring terminal diagram. Three-core shield cable (RVVP3×0.75mm2) shall be used for
the connection of the temperature sensor. Common two-core cable (RVV2×0.75mm2) shall be
used for the connection of flow switch to connect to the NO contact of the switch, i.e. the
opening point when waterless. Two buttons can be connected to the external of remote start
and stop.
(11) If the customer desires the linked control of the water pump, connect the water pump as shown
in the diagram, where an intermediate relay is required. If the function of linked control of water
pump is not needed, ensure that the water pump is started before starting the machine.
CAUTION: An independent power supply box needs to be equipped with the power supply of
the water pump.
28
Intermediate Electric control cabinet

relay customer wiring terminal
Pump contactor
Pump motor
[Diagram for Wiring of Water Pump Linked Control]
(12) The wiring ports for remote start/stop, flow switch, cool/warm switch, water pump linked control,
alarm indication, etc. are reserved in the electrical cabinet of the unit, with the numbers shown
in the diagram below.
Only double head

Customer wiring terminal
Inside electric control cabinet
1 2 3 4 5 6 7 8 13 14 15 16 17 18 19 20 21 22 23 24
Inside electric
control cabinet
2
Pump intermediate relay
1
Refrigeration lamp
2# alarm lamp
Remote Start
Remote Stop
1# alarm lamp
Flow switch
[Numbers of Functional Ports Reserved in Electrical Cabinet]

(13) Passive inching button is used for remote start and stop, and the flow switch must be
connected to the NO contact, or the machine cannot be started.
Passive holding switch is used for cool/warm switch, e.g. common selection switch. Controls of
29
large power electrical appliances such as water pump and user electric heating must be
interfaced with a relay, or the PLC might be burned. Other outputs can be directly connected to
indicator lamps or alarms.
2. Electric parameter table

(1) Power Table
Main power Power Range Max. allowed

Model running
V Hz Highest/+% Lowest/-%
current/A
LSBLGW380/C 380 50 +10 -10 261.6
LSBLGW500/C 380 50 +10 -10 375
LSBLGW600/C 380 50 +10 -10 395
LSBLGW720/C 380 50 +10 -10 507
LSBLGW880/C 380 50 +10 -10 636.6
LSBLGW1000/C 380 50 +10 -10 750
LSBLGW1200/C 380 50 +10 -10 790
LSBLGW1420/C 380 50 +10 -10 1014
(2) Compressor & fan
Compressor Fan
Max.
Model Start Rated Rated Rate of Rated
running Fan
Quantity current/ current/ power/ fan current/
current/ quantity
A A KW /RPM A
A
LSBLGW380/C 1 586 228 227.4 124 6 940 5.6
LSBLGW500/C 1 805 340 280.3 159 8 940 5.6
LSBLGW600/C 1 805 340 326.7 187 10 940 5.5
LSBLGW720/C 1 917 507 408.8 234 10 940 5.6
LSBLGW880/C 2 Refer to 380 /C+ 500/C 14 940 5.6
LSBLGW1000/C 2 Refer to 500/C 16 940 5.6
LSBLGW1200/C 2 Refer to 600 /C+ 600/C 16 940 5.6
LSBLGW1420/C 2 Refer to 720 /C 20 940 5.6
30
3. Control Flow Chart
2 Compressors 6 to 10 Fans
380VAC Double-Head 14 to 20 Double-Head
3P+N+PE Compressors
Moulded Case M
M
Circuit Breaker ~ M
Moulded Case ~ M
Circuit Breaker ~
~
Phase Sequence
Compressor
Miniature Thermorelay
Compressor
Circuit Fan
Thermorelay Thermorelay
Fan
Breaker
Thermorelay
Compressor
Contactor
Compressor Fan Contactor
Star-Delta Start
Contactor Fan Contactor
星三角启动
Star-Delta Start
Input Output
Module Module
Commu PLC CUP Module
nication
Terminal for Terminal for

HMI External Signal Output Action
e.g. Temp. e.g. Solenoid
Pressure Valve
 Guidance of common electric problems treatment:

1) Phase sequence protector:
a) Protective condition: anti-phase, phase lack, overvoltage, undervoltage or imbalance
of three-phase voltage of power input terminal of phase sequence protector;
b) Results of action execution: power module failure lamp is ON, touch screen displays power
failure and fails to be started;
c) Processing mode: see the power module, exchange any two unit incoming lines if it is
anti-phase;
Please do not start until power gets right with failure removed in case of other failures.
Notes: this module has the important action of compressor protection. The imbalance rate of voltage of
current is usually specified by compressor manufacturers, and burn-down due to overheating will be
resulted from long-time operation under abnormal working voltage.
2) Miniature Circuit Breaker:

a) Protective condition: current passing the miniature circuit breaker exceeds its numerical
31
protection value;
b) Results of action execution: power-fail of corresponding circuit, failure of start, circuit breaker
switch positioned in the OFF terminal
c) Processing mode: inspect there is burn-down of component(s) or short-circuit between circuits.
If any, please replace the component(s) or modify wiring;
You may attempt to set the circuit breaker to ON terminal, if it immediately trips once again, it indicates
that there is always a condition of short circuit, in this case, inspect the line and components until normal
pull-in is available.
Notes: Before inspection, please switch on the breaker once without electricity. The existence of heavy
current shock may result the damage of the miniature circuit breaker. At this moment, switch-on without
electricity is also impossible. When switch-on is successful, please test with a multimeter whether the
circuit is conducted. If not, you can sure that mechanical mechanism is normal but electric mechanism is
damaged. In such case, please replace the miniature circuit breaker, and inspect the above steps.
3) Fan Thermorelay
a) Protective condition: fans current overload or phase lack;
b) Results of action execution: units stop, display of fans overload on touch screen, thermal
overload relay trip, failure of start.
c) Processing mode: inspect whether there are fans wiring loose. Inspect whether the value of
fans protection is in a proper position. Inspect whether fins are fouled. Please reset the
thermorelay manually, if needed.
Notes: Because the motor and the thermal overload relay have different thermal inertias, the
temperature of motor is still very high while the thermorelay can be reset. Please inspect whether the
temperature of motor is too high when you can’t sure the failure clearly. Immediate resetting is
impossible in the case of overload trip. You have to wait until the thermal effect of the thermorelay is
over.
4) Moulded Case Circuit Breaker

a) Protective condition: there exists too heavy current or short circuit in the units
b) Results of action execution: the unit shuts down and power down.
c) Processing mode: inspect whether the electric control part of units and insulation of loads are
normal, if yes, power on and start the units again, and measure whether the working current of
compressors and system pressure are normal
5) Compressor thermorelay
a) Protective condition: too heavy compressor current or existence of short circuit failure
b) Results of action execution: units stop, display of compressor overload on touch screen,
32
thermal overload relay trip, failure of start.
c) Processing mode: inspect whether the compressor part and insulation of loads are normal,
inspect the pressure value when an alarm is given, and balance the pressure if it exceeds the
running range. Please monitor the current of compressors in real time to ensure whether it is
within normal running after the compressor thermorelay is reset.
6) Sensor Failures
Sensor failures include short circuit and open circuit of the temperature sensor and the pressure
sensor (transformer). The current transformer is also included according to the stepless type unit.
a) Protective condition: any sensor failure
b) Results of action execution: stop of units, display of corresponding sensor failure on touch
screen, failure of start.
c) Processing mode: inspect whether the wiring of faulty sensor is proper and firm, and whether
the sensor itself is normal.
4. Control Screen Operation

Initial Startup
 Before power up for the first time，make sure that the wiring is firm between the control box
and the main switch ， the insulation resistances reach the requirements ,and the earth wire
has been properly installed.
 The wiring might be loose due to the factors such as long-distance transport. Carry out
complete inspection for the bolts of all wiring terminals for looseness 。
 Be sure that the distribution capacity is compliant with the power of the unit and the diameter
of the selected cable can bear the maximum working current of the unit.
 Inspect whether the red emergency stop button on the control box is in natural state.
4.1 Introduction of Control Screen:
2
4 3
【Home Page】
1) Power indicator (yellow), which is on when display is powered on; it is off when powered off.
2) Status indicator (green), which flashes at low frequency when display is normally operative,
33
otherwise it is off.
3) Communication indicator (red), which flashes at high frequency when display and PLC
communicate normally, otherwise it is off.
4) PLC and touch screen procedure version: showing the number of PLC and touch screen
procedure version used by the current unit.
4.2 Basic Interface and Operations:
Indicate that
the system is
initializing.
(last about 30
seconds , flash
1/1sencond)
After the system initializing is completed, please clink on button, and the “Password Input”
dialog will be popped up, please input the User Password(58806) or User Manage Password
(40828),and click “ENTER” into the next interface (Mode Setting Page)
Password Input Page
 Mode Setting Page
34
【Mode Setting Page】

Control mode and working mode are to be set in this page:
1. Control mode and running mode which have been selected currently for units are displayed here,
and this position will correspondingly vary according to the choices of customers when selection of
modes is changed.
2. Selection of unit control modes, including three modes: “LOCAL”, “REMOTE”, “TIMED”, i.e. local
control, remote control, timing control.
3. Selection of unit operation modes, including three modes: “PUMP”, “COOLING”, i.e. pump mode,
cooling mode.
4. Click on “PgDn” to enter the next page (Main Page).
5. Click on “BACK”, return to the homepage of units.
Note:
① The control mode and running mode can be selected optionally in standby status, while only
the control mode can be switched in running status.
② Control Mode: The selection of the ways of Unit starting/stopping. “LOCAL” indicates you can only
start or stop the unit through “Start/Stop” button in touch screen. “REMOTE” indicates you can only
achieve the unit starting or stopping though the “Remote Start” and “Remote Stop” hardware
interfaces; “TIMED” indicates the unit can achieve timing start/stop according to the time set by the
user.
 Main Page
35
2 6
3
4
7 8 9 10 11
【Main Page】
1. System Status: Current system status of units is displayed here. The status of system possibly
displayed is as follows:
1) Standby status: in normal condition, displaying “Standby status” after the unit is powered on.
2) Running status: indicating that starting of unit compressors has been finished (entering the running
status after double-head Start of one compressor), and it has entered the process of automatic
energy adjustment from this point.
3) Pause status：The unit enters “Pause” status when the current detection water temperature (chilled
outlet water temperature in single-unit or chilled inlet water temperature in Multi-units) is lower than
the setting temperature of unit pause. The compressor start to run until the current detection
temperature is higher than the setting temperature of compressor start, then the unit enter “Running”
status.
4) Shutting down status: the status display “shutting down” after the unit has been confirmed to
execute shutdown action. After finished, the unit enters “Standby” Status.
5) Protection status: indicating that the unit is in a failure status currently, click on "alarm information" to
see alarm details.
2. Control mode and running mode: the current mode will be displayed here. For example, the current
page displays that the unit is in a “LOCAL MODE”, and the running mode is “PUMP MODE”.
3. Detection Mode: Leaving water control is by default only in the single-unit mode, with entering water
control not allowed; entering water control is by default in the multi-units combination mode, with
setting of leaving water control not allowed。
4. Combination Mode: indicates “Single-unit” when the unit isn’t in the case of multi-combination
control and indicates “Multi-Units” when the unit is in Multi-combination control. (Note: When the
system has only one unit, please don’t set to multi-unit control)
5. This position is the unit alarm display area, and alarm information of failure content will be displayed
here in a mobile mode in case of any failure in units.
6. Functional key area of units. It has the functional keys of “SETTING”, “ALARM”, “STATUS” and
36
“Multi-Unit” through which different operating interfaces are accessible. Introduction of their
functions will be detailed hereafter.
7. Start is required upon completion of unit set-up, directly click on “START” button on the lower left,
and the following dialog box will be popped up at this moment: click on “CANCEL” if you don’t
expect to execute the start.
【Ensure unit start-up】

8. The sign “Failure to start, please check the status” will appear when the conditions of compressor
stating can’t be required.
9. There is a rotate button with a key beside the touch screen. When the units need to be maintained
by the user or after sale service personnel while expecting to see parameters from the touch screen,
the user may rotate the button to the service point, and “System under maintenance, please don’t
start up!” will be displayed below main page at that moment. Start operation is not allowed at this
moment. Any action of maintenance or power operation shall not be taken in the absence of
personnel who have been specially trained and certified!
10. Help information, abbreviation of words in units will be explained in detail in help interface.
11. Click on “BACK”, return to previous page of units------mode selection interface.
Note:
button disappear when the combination mode is “Single-unit”. Click
button to query the current unit status.
Starting Operation
The system is in pause state when the water pump has been completed to open, but the compressor is
unable to start because some other factors can’t satisfy the condition of compressor starting, the
interface indicates “Failure to start, please check the status”. The starting conditions include oil heating
time 、restart delay、the temperature of compressor starting. In this case, only when all of the conditions
have been meet, the unit starts to operate the compressor, otherwise the sign “Failure to start, please
check the status” will keep displaying in the main page.
Note: Clicking on button is invalid when the unit is in failure. The unit can start normally only
when all of the alarm have been eliminated and reset manually on the touch screen interface.
37
When the current ambient temperature is beyond the allowed running range, the below page will be
popped up:
If the current temperature return to the rage, click to the“OK”and the unit will start to run normally.
Shutting down Operation
Click on button , and the “Confirm Shutdown” dialog will be popped up. Click on “Confirm” if
you ensure execution of Shutdown action, the system status indicates “Shutting down”. (Note: The
system status indicates “shutting down” even the requirements of shutting down the compressor are not
meet. The unit will execute shutdown action automatically after all of the requirements have been
satisfied. )
The action of 4 functional keys in main page will be detailed in subsequent sections:
 Setting
Click on in main page to enter the password page. Click on the dialog box of password
input, an input keyboard will be popped up in the interface, input user manage password “40828”, then
click on “Enter” in numeric keyboard, the dialog box disappears, click on “ENTER” to enter “User
Parameter Setting Page”.
38
【User Parameter Setting Page 】
Password Error Page
“Password Error Page” will be popped up when the password is wrong, click on button to
return “Password Input Interface”, input the password again to enter the next page.
Note:
① “Max” in the upper left indicates the upper limit of the setting parameter; “Min” in the upper right
indicates the lower limit.
② “Automatic On/Off”: Only displaying under Timed mode.
39
Explanation:
① Target Temp. (Chilled Leaving Water): The target temperature of the chiller leaving water
② Temp. / Compressor start (Chilled Leaving Water): One of the compressor starting conditions
required to be achieved for the chilled leaving water temperature. The compressor can start only at
the current chilled leaving water temperature ＞ the setting value in cooling mode, or the current
chilled leaving water temperature ＜ the setting value in heating mode.
③ Temp. Adjustment Period: The time interval between two temperature detections.
 Clock Setting
Manual
input is
allowed
Clock Setting
Click on the numerical box, the numeric keyboard will appear, input the time, click “ENT” to save and
take effect. Click “ESC” to cancel the input value.
Note: Please pay special attention in setting of time and date to the fact that setting of
non-existent date or time is not allowed, and we assume no liability or responsibility for setting
of non-existent date or time and consequence resulting from this setting.
 Adjust Screen
User can increase and reduce the brightness and contrast of screen by clicking on “+”and “-” in this
page.
User can also open and close the keypad tone of screen by clicking on “ON” and “OFF”.
User can modify the time of backlight by clicking on the numeric box following the time of backlight.
Electric control capacity displays the battery capacity of PLC whose battery is used for supplying power
for PLC interior time in the case of failure to engage PLC. Reset of PLC interior event will be resulted
40
from too long power-fail time of PLC module without battery.
 Automatic On/Off
If the automatic on/off function is needed, please switch to “TIMED” mode in control mode (as shown in
Picture 2) firstly, then enter user parameters setting page, click on button to enter
the following page ,and set the starting times and shutdown times.
Manual Input
Is allowed
Inching
switch
Automatic On/Off Setting

Any time every day in a week can be selected, and the units will be started or stopped at the time points.
When a period of continuous running time (for example from 10:00 Tuesday to 16:00 Thursday) is
necessary, you can set the time 10:00 in starting time and 0:00 in shutdown time on Tuesday and click
on “ to switch to , set the time 0:00 in starting time and 16:00 in shutdown
time on Thursday and click on “ to switch to ,all of the others time buttons are
. Pay attention to that the starting time must be before the shutdown time.
Since system interior time is used for timing start / stop, please draw attention to check whether the time
of the system is correct when you are using this function.
 Comm. Setting
Click on to enter the below page:
Note: “1#Comp. ON” “2#Comp. ON” only appear in dual-compressors units.

① Mult-Units: When the unit need to be multiple controlled, please contact the after-sale service
41
engineers to do settings of the unit. After setting well, press the button, it will turn to
, then the number of multi units should be set according to the practical situation.
② “1#comp. on” “2#comp. on”: No.1 or No.2 compressor can be selected to work or not, when the
compressor meet the conditions it will shut down refer to the stop progress if user want to stop one
compressor.
Read serial pot information
Click on to read serial port information when the unit need to be multiple controlled.
 Status
Click on in main page to check the current unit status information.
Status Information
The upper left in the page display the refrigerant type; the upper right display the station number address,
the station number of master is set to 1.
Note:
To start up, following conditions are required:
① “Restart Delaying” need to display “NO” ,if “YES”, it indicates the delaying period has not achieved.
② ”Water Temp. Allow Compressor Start” need to display “YES”, if “NO”, it indicates the current
temperature is not able to meet the compressor starting condition.
③ “Remaining Oil Heating Time” need to display “0”, if more than 0, it indicates the oil heating is in
process.
42
To shut down, the following condition is required:
① ”Min. Running Time Elapsed” need to display “YES”, if ‘NO’, it indicates the shortest running period
has not achieved.
Current Data Display
Please click on button to enter the current data interface, the interface indicates current detection
data. User can enter this interface to query the temperature information when there are alarms such as
temperature too high or too low.
Current Data Display

Input
Input Status
“ON” as displayed indicates the input point is closed; “OFF” as displayed indicates the input point is
open.
Note:
① “Remote Start/Stop” is available only under REMOTE mode.
② “Water Switch”: indicating that current water flow status of chilled water system. “OFF” displayed in
no water flow state, otherwise “ON”.
③ “Contactor Protection”: indicating that when the compressor start to run, the contactor act
normally, “OFF” switch to “ON”.
43
④ All of protection switch is “ON” in normal condition and “OFF” in failure status.
Output Status
Output
“ON” as displayed indicates the output point is energized; “OFF” as displayed indicates the output point
is de-energized.
 Alarm
Alarm Information Page
Click on button in Main Page to enter the alarm information page.

If there is any alarm, the unit will execute alarm procedure action. The unit alarm status can’t be
removed until all of the alarms have been eliminated and alarm shutdown process has been finished.
Click on button and “Fault” in main page disappear, the unit returns to normal. If the warning
message is more, please click on to check. These in red color indicate the alarms which
have not been eliminated; these in white color indicate the alarms which have been eliminated.
Note:
1. High-Pressure Protection is unable to reset in alarm information page, manual reset in the high
pressure switch (installed in the discharge pipe) is needed.
2. Compressor and fan overload protection are unable to reset automatically, please check the
44
relevant thermal relay in the control box to reset manually.
History Alarm Information
Click on button in Alarm Page to enter history alarm information query

information, as shown in Picture 8.2. Max.5 warning messages can be recorded meanwhile. The
messages will be updated automatically if there are more messages.
History Alarm Information Query

Note:
1. The history alarm information record the unit operating parameters when there happen unit alarms
during the compressor running.
Content of Failure Interface in English
水流断 Water flow fault
防冻保护 Anti-freeze Protection
1#高压保护 1# High-pressure protection
1#低压保护 1# Low-pressure protection
1#机内保护 1# Compressor Motor Protection
1#油位过低保护 1# Low Oil Level Protection
1#接触器保护 1# Contactor protection
1#油压差保护 1# Oil differential pressure protection
1#压缩机过载 1# Compressor overload
1#风机过载 1# Fans overload
电源保护 Power Failure Protection
进水温度传感器故障 Entering water temp. sensor failure
出水温度传感器故障 Leaving water temp. sensor failure
环境温度传感器故障 Ambient temp. sensor failure
1#翅片温度传感器故障 1# Fin temp. sensor failure
1#排气温度传感器故障 1# Discharge temp. sensor failure
2#翅片温度传感器故障 2# Fin temp. sensor failure
2#排气温度传感器故障 2# Discharge temp. sensor failure
1#吸气压力变送器故障 1# Suction pressure failure
1#排气压力变送器故障 1# Discharge pressure failure
45
2#吸气压力变送器故障 2# Suction pressure failure
2#排气压力变送器故障 2# Discharge pressure failure
1#排气温度过高保护 1# High discharge temp. protection
1#翅片温度过高保护 1# High Fin temp. protection
1#压差保护 1# Differential pressure protection
1#吸气压力过低保护 1# Low Suction Pressure protection
1#排气压力过高保护 2# High discharge pressure protection
1#模式切换失败 1# Mode switch failure
模式水温保护 Mode water temp. protection

1#膨胀阀模块故障 1# EXV module failure
2#高压保护 2# High pressure protection
2#低压保护 2# Low pressure protection
2#机内保护 2# Compressor motor protection
2#油位过低保护 2# Oil level protection
2#接触器保护 2# Contactor protection
2#油压差保护 2# Oil differential pressure protection
2#压缩机过载 2# Compressor overload
2#风机过载 2# Fans overload
2#排气温度过高 2# High discharge temp. protection
2#翅片温度过高 2# High Fin temp. protection
2#压差保护 2# Differential pressure protection
2#吸气压力过低 2# Low Suction Pressure protection
2#排气压力过高 2# High discharge temp. protection
2#模式切换失败 2# Mode switch failure
2#膨胀阀模块故障 2# EXV module failure
站号设定不成功 Invalid Address Number
 Multi-Units Status
Multi Units Status

In this page, you can query the status of different modules through choosing the corresponding module
46
button, also can check the status of all modules meanwhile through master-monitoring.
Master-Monitoring Page
Click on to enter the next page, it will show the information of all connected units as
following: The communication, alarm information, status, refrigerant type of each unit can be inquired in
the following pages.
Click on to enter the next page.
Note:
① Max.8 units can achieve combination control, the unconnected unit can access the combination
control system at any time as long as the unit is powered on and connected with the system by
communication cable.
② The “Status” displays “Run” until the unit finish the starting action and enter the process of automatic
energy adjustment, otherwise displayed “shutdown”
47
5. Control Screen Menu Structure
Touch Screen Tree diagram

Homepage
Mode Setting
Main Page
Setting Multi-Status Alarm Status

(Password Input)
User Parameter Multi Units Alarm History Alarm

Setting Status Information Information
Query
Module Status Status

Choose Information 1 Information 2
Clock Adjust Automatic Comm. Status Current Data Input Output

Setting Screen On/Off Setting Information Display
48
6. Introduction of Major Electric Components
Collect all digital quantities and
analog quantities on units as well
as inputs of quantities and touch
Programmable Logic
screen commands, and realize
Controller
different outputs by judgment of
(PLC)
procedures to meet the
requirement or normal and safe
running of units.
Communicate with PLC to display

Touch Screen
the running status of units, set the
Human-Machine
running mode of units and control
Interface
the running parameters of units.
(HMI)
Achieve AC220V/DC24V to
provide power supply for touch
Switch Power Supply screen, also for PLC and
intermediate relay in some
tailor-made products.
An element necessary for

achieving compressor contactor
star-delta switchover. The time set
Time Relay
above is defined as the star
running time (3 to 6S)
Work out the suction superheat in

the running process of
compressors through the
temperature sensor (NTC) and the
EXV Control Module pressure sensor connected to the
module, and regulate the opening
of EXV through the suction
superheat to enable units to run in
a stable status of energy-saving
Heat will be generated when

current passes through a
conductor. Heat effects are
different due to different types of
current passing through thermal
Thermal Overload sheet metal inside the
Relay thermorelay. When the heat
effects are accumulated to certain
degree, the thermal sheet metal
will be deformed so as to switch
off front and rear parts of the
thermorelay forcibly to achieve the
purpose of protection.
49
Detect the quality of power

supplied to units by the user,
detect the voltage range of the
power, the imbalance rate of
Power Protection
three-phase voltage, phase
Module
sequence and phase lack, and
protect the units by inspecting the
quality of power.
(for CE )
Transform the electrical system
applied by the user into AC220V
for supplying power to the control
Isolating Transformer circuit. It can isolate harmonic
disturbance between circuits and
increase control accuracy.
The moulded case circuit breaker

acting as a main circuit switch with
Moulded Case Circuit
circuit protection is generally
Breaker
applied for newly developed units.
The intermediate relay has the

major action of separating control
circuit from power circuit to avoid
heavy current of the latter from
Intermediate Relay
returning to control circuit in case
of any failure and burning down
PLC and other important
components.
Control on/off of circuit, and also

Miniature Circuit
has the action of short circuit
Breaker
protection on control circuit.
Transform main incoming current

into low current to be accessed to
the thermal overload relay to
Current Transformer enable the thermal overload relay
to judge whether the current is too
heavy so as to play a role of
current protection.
50
IV. Maintenance and Commissioning
1. Commissioning
1.1 Electrical System Connection Inspection
1) Inspect whether power distribution capacity is compliant with the power of the unit before the first
start-up, and whether the diameter of the selected cable can bear the maximum working current
of the master compressor.
The max economical conveying distance:
The max loading time in a year（h） Copper core length(m)
<3000h 264
3000～5000h 294
>5000h 331
2) Inspect whether the electric mode is compliant with that of the unit, three-phase five-line (three
phase lines, one zero line and one earth wire, 380V±10%).
3) Inspect whether the maximum phase voltage unbalance is compliant with the requirement, 2%
for the maximum permissible phase voltage unbalance and 5% for the phase current balance.
The machine must not be started up when the phase voltage unbalance exceeds 2%. If the
measured unbalance% is excess, the power supply sector shall be informed of immediately.
The formula for calculation of phase voltage unbalance% based on the maximum deviation
from the average voltage is: voltage unbalance% = maximum deviation from average
voltage/average voltage.
e.g. at nominal voltage 3N~, AC380V, 50Hz, the measured UAB=376V, UAC=379V, UBC=385V.
Average voltage = (376+379+385) 3= 380V
Determined deviation from average voltage:
△UAB=380-376=4V, △UAC=380-379=1V, △UBC=385-380=5V,
Maximum deviation: 5V
5/380=1.3%, the maximum phase voltage unbalance is 1.3%.
4) Inspect whether the supply circuit is the compressor is firmly and properly connected, and
tighten it if there is any looseness. The screws might be loose due to the factors such as
long-distance transport and hoisting of the master compressor. Or, the electrical elements (e.g.
air switch, AC contactor, etc.) in the control cabinet of the master compressor and the
compressor might be damaged.
5) Carefully inspect all the electrical lines with a multimeter, and whether the connections are
properly installed. Carry out measurement in mega ohm and ensure that there is no short circuit
at the shell. Inspect whether the earth wire is properly installed, and whether the insulation
resistance to ground exceeds 2MΩ. And inspect whether the supply line meets the requirement
of capacity.
6) Inspect whether disconnection switch is installed to the supply line of the supply unit.
51
7) Carry out complete inspect for all connections of the main circuit in the control cabinet and all
external connections of the control circuit before power connection (e.g. oil heater, compressor
electronic protection, circulatory water temperature sensor, target-type flow switch connection,
water pump linked control, communication line connection, etc.); inspect the bolts of the wiring
terminal for looseness. Inspect whether various electric meters and appliances are properly
installed, complete and available. Inspect the interior and exterior of the electrical cabinet,
especially various wiring ports, for cleanness. If the communication lines of the PLC and control
screen are damaged, refer to the diagram below.
8) After the inspection for all the above items is complete, connect the control cabinet and the
supply indication lamp will light up, indicating that the oil heater is working. Observe whether
the phase loss protection is in normal condition, if it is (green light on), close the single-pole
switch (QF2) in the control cabinet, then the control circuit begins working, and the touch
screen and PLC control are put into operation.
9) Before start up the machine, inspect whether the external system of the unit meets the
conditions for start-up (e.g. whether the water cooling pump of the system is externally
controlled or interlocked with the master compressor, and that the water pump must be started
before starting up the master compressor via external control).
9 needle type D plug female head
9 needle type D
plug female head
RJ45 crystal head
9
8 8
7 7
6 6
5 5
4 4
3 3
2 2
RJ45 cable 1 1
RJ45 crystal head line
87654321
RJ45 crystal
head
[Communication Lines of PLC and Control Screen
52
1.2 Electrical Elements Parameters Settings Inspection
1) Inspect whether the ports of linked controlled unit are properly connected.
The connection way for linked controlled unit is as below:
11号机组
# unit 22号机组
# unit 88号机组
# unit
9 10 1112 9 10 1112 9 10 1112
Multi-link connection:
The user wiring terminals 9, 10, 11, 12 of each unit are communication line terminals for multi-link.
These terminals can also be used if the upper computer is selected. Attention: either upper
computer or multi-link function can be chosen. The use of both requires application for
customization.
Use 0.5mm2 3-core shield wires to connect the unit.
Double-head unit is considered as one unit. Maximum 8 sets can be connected.
The method of connecting upper computer via Ethernet port:
The connection via Ethernet instead of RS485 serial connection required customization. The
connection way is as below:
Ethernet port,
only if customized
Wire number of
RJ45 crystal head
RJ45 crystal head RJ45 internet cable RJ45 crystal head
2) Inspect whether the fan overload protection value is set correctly. The current value for normal
operation fan is 3.5~4A. After a fan overload trouble, press the blue button in the heat relay to
reset.
53
Protection setting of
fan heat relay
overload value, the
number of which
corresponds to the fan
overload protection
value.
3) Inspect whether the compressor overload protection value, which shall not exceed the
maximum compressor permissible current value indicated in the nameplate on the compressor,
is set correctly. The compressor overload protection value generally equals to the set value of
heat relay (similar to fan heat relay) multiplied by variable ratio of current inductor, which is
(250/5)50 in the following case.
Protection setting of
fan heat relay overload
value, the number of
which corresponds to
the fan overload
protection value.
3) Inspect whether the value of phase loss and reversal protection is set correctly. The
over-/under-voltage protection value shall be ±10% of the rated voltage.
1.3 Unit Parts and Inspection of Leak Points

1) The discharge line valve and suction line valve of the compressor must be fully open (turn
anticlockwise to open) and the cores shall be tightly locked to prevent leakage of refrigerant.
The discharge line

valve shall be open
(both valves in the
figure are closed, and
shall be opened
before start-up).
54
2) Inspect whether moisture content of the system exceeds the limit
Excessive moisture content in the refrigerant system of the unit might cause ice block, copper
plating, etc. that would seriously affect the safety of the unit. Therefore, the dryness of the
refrigerant system of the unit shall be inspected from the sight glass before and during
operation of the unit, purple indicating dry, and pink moist, as shown in the below figure. When
the color turns to red, the filter core in the unit shall be replaced with a dry one.
The color is indicated in the

center and compared with
the color card around it to
reflect the moistness in the
system.
3) Sufficient lubricating oil in the oil tank (not lower than 1/2 of the oil level in the high oil
immersion lens), and no deterioration (blackness).
Inspect the oil level and quality before start-up for the two factors have direct impact on the
performance and reliability of the unit. There must be sufficient lubricating oil in the unit. And
during the shutdown of the unit, the high oil immersion lens must be full of oil.
The oil must be full in

stop status of the
unit, and above the
1/2 position in stable
operation.
When the unit is in stable operation, the oil level in the high oil immersion lens should be at
least above the 1/2 position. And there shall be no deterioration (blackness) of the lubricating oil,
or else, qualified lubricating oil shall be changed before operating the unit.
4) Coil fin cooling fan shall rotate in correct direction without reverse rotation or shutdown.
Before operation of the unit ,Inspect whether the fan networks are deformed under stress,
whether there is friction and collision between the networks and the blades, whether there are
foreign matters in the network, and whether the fin is deformed or damaged caused by collision.
55
There should be no
deformation of the
fan guard or foreign
matters in it.
Operate the fans one by one before operating the unit, and inspect whether there is abnormal
noise in the fan caused by poor lubrication of the bearing or friction of foreign matters, and
whether the fan rotates reversely or does not rotate.
5) Inspect whether the directional elements such as one way valve, solenoid valve, electronic
expansion valve, etc. are installed properly. The directions of the one way valve and solenoid
valve are indicated on the valves. As for the thermostatic expansion valve and electronic
expansion valve, if the valves are upward, the direction is generally high-in and low-out.
Refrigerant Flow Direction

Refrigerant Flow Direction in Electronic
Expansion Valve
6) Inspect whether the pressure sensor stop valve, dry filter front/rear angle valve, liquid/air
sampling stop valve and injection stop valve, etc. are all open.
When the unit stops, the high and low voltages shall be almost the same. After the start-up, the
low voltage decreases, and the high voltage increases. If there is no voltage change certain
time after the start-up, inspect whether the liquid/air sampling stop valve is open.
7) After the unit is installed and before connected, it is required to tighten the connections in the
electrical cabinet of the unit one by one.
8) Inspect the bolts of the unit for looseness.
After the unit is transported and installed, it is required to inspect whether the fixing bolts of the
unit (e.g. fixing bolts at compressor base angle, at post and beam of the unit, and at pipe clamp,
etc.) and of the electrical elements (e.g. fixing bolts of PLC and of insulating transformer, and
56
connection bolts of upper/lower terminals of AC contactor, etc.) are firmly fixed.
9) Inspect the looseness of the connections in the electrical cabinet, especially the electric part in
the cabinet. The parts connected by bolts might be loose due to transportation. If there is any
looseness, tighten it to avoid burnout of circuit or element caused by poor contact.
Inspect the looseness of the terminals and poor contact caused by vibration and collision during
transportation and installation (especially the electric part; ensure the connection points of all
terminals are firm and reliable before electrification).
All terminals of all

heat relays of the
fan must be firm
All connection points of

terminals must be firm
and reliable.
Inspect all terminals

for firmness and
reliability before
electrification.
Inspect whether there is poor contact and short circuit caused by dust, moisture, etc. in the
electrical cabinet, and whether the values of all temperature sensors are normal. During the
shutdown of the machine, the indicated temperatures of discharge, fin, and the environment
shall be almost the same, and the entering and leaving chilled water temperatures shall be
almost the same.
10) Before the unit leaves the factory, the control cabinet is well connected with main motor,
electrical actuator, and sensor elements of pressure temperature, etc. Therefore, the wiring on
site for the user is very simple. Only the chilled water flow switch line and chilled water pump
linked control line (control contact is active) need to be connected. For the detailed connection
way, please refer to the circuit wiring diagram in the operation manual for the unit. (The
attached circuit diagram represents the case of air-cooled heat pump unit for user’s reference,
as for the details, the operation manual supplied with the unit shall be final.)
11) Target-type flow switch is set on the chilled water pipeline which shall be installed at the outlet of
the chilled water. The NO contact of the target-type flow switch shall be connected to the
control circuit as per the wiring diagram.
Note: Disordered water flow may lead to wrong action of the flow switch; therefore, the control
cabinet will command the unit to stop after receiving continuous disconnection signals during
10 s.
12) The tube where the temperature sensing probe is installed shall be filled with lubricating oil or
other grease that will not freeze at the temperature of the leaving chilled water for the
convenience of heat transfer. Thermostatic insulation and enclosing measures shall be taken
for the temperature sensing device.
Inspect whether there is temperature deviation for the entering and leaving water temperature
57
sensor caused by insufficient heat transfer oil in the thermostatic pipe.
There shall be sufficient heat

transfer oil in the thermostatic
pipe of entering and leaving
water temperature sensor for
more accurate collected
temperature.
Armored dip-type
temperature sensor
For later armored dip-type temperature sensor, no lubricating oil is required for heat transfer.
1.4 Complete Machine Performance Parameters Inspection

1) Parameters Inspection before Start-up
Before start-up of the unit, the following performance parameters need to be inspected:
(1) High/low voltage value of the system. In the case of the unit shut-down and waterless in a long
time, the liquid and gas of the system shall be equivalent and close to the saturation pressure
corresponding to the current ambient temperature. The correlation of saturation temperatures
and pressures (the pressures in the list are gage pressures, among which, the atmospheric
pressure is 0.1MPa) of R134a refrigerant is shown in appendix 1:
In shutdown status,
the high and low
voltages shall be the
same and equal to the
saturation pressure
corresponding to the
current temperature.
In the pressure gauge scale, taking the right figure for example: the outside values are pressure
values (unit: bar), and the inside values indicate saturation temperatures of refrigerant R134a
respectively under the relative pressure. The types of refrigerants indicated in different pressure
gauges might differ. [Table 1]
R134a Refrigerant R134a Refrigerant

Refrigerant Refrigerant
Pressure (Gage Pressure (Gage
Temperature ℃ Temperature ℃
Pressure) MPa Pressure) MPa
0 0.19 25 0.57
5 0.25 30 0.67
10 0.32 35 0.79
15 0.39 40 0.92
20 0.47
58
If the high/low voltage deviates much from the saturation pressure corresponding to the current
temperature (more than 2bar), maybe there is leakage or insufficient refrigerant in the system.
(2) Inspect whether the oil heating of the unit is normal .
Before start-up, it is necessary to inspect whether the oil heating in the unit is available, and
whether there is the condition that the oil heater does not work because of no power supply. It is
particularly important in winter when the temperature is low and the failure of oil heating might
lead to poor lubrication of the unit. The optimum working temperature for current types of
lubricating oil is generally around 40℃.
Compressor oil
heater, working
when the unit is
electrified.
(3) Inspect whether there is alarm for trouble of the display screen. if there is, the trouble must be
corrected.
(4) Inspect the electronic expansion valve control module for alarm trouble.
(5) Inspect whether various temperature points displayed on the display screen are within the
normal range.
Before the operation of the unit, the showed temperatures of discharge、fin and the ambient
temperature are close to the current actual ambient temperature, and whether the entering and
leaving water temperatures are close to the water temperature at the user side. If there is any
obvious deviation of the above temperatures, inspect whether the temperature sensor is in
normal condition and whether the connection is firm and reliable.
Values of various
temperature and
pressure points
showed in the main
page of the unit.
(6) Inspect whether the flow in the water pump meets the requirements of the unit.
(7) Inspect whether the power supply of the unit is stable.
2) Parameters Inspections during Start-up and Operation
59
(1) The maximum range of parameters for normal operation of R134a refrigerant unit
See table 2 for the maximum range of performance parameters of R134a refrigerant:
[Table 2]
Refrigeration
Working Condition
Discharge temp. ℃ <110
Suction temp. ℃ --
Condensation temp. ℃ <65
Evaporation temp. ℃ <15
Economizer super-cooling degree ℃ --
Suction super-heating degree ℃ ～
Discharge pressure MPa <1.8
Suction pressure MPa <0.38
(2) Keep good record of unit data during commissioning.
60
2. Maintenance
2.1 Common Troubleshooting
1) High Voltage Protection
High
voltage
protection
Yes
Yes
Reversed cooling and Adjust operation

heating mode
No
Blower stops rotating or rotates in Yes

reversed direction when cooling;
water pump is not open or the Inspect the blower or open
flow insufficient when heating the water pump.
No
Yes
Expansion valve Replace the
can not be opened. expansion valve.
No
Yes
Press controller is
in trouble. Replace the press
controller.
No
Yes
Fin heat exchanger for cooling is too Replace the heat
dirty or aged; or, too heavy exchanger.
encrustation in tube shell for
heating.
No
Yes
One way valve is Replace the one way
blocked. valve.
No
Yes
Air exists in system
(generally likely after Empty the air, re-extract
service of the unit) vacuum if necessary.
No
Yes
False alarm of Inspect whether it is
controller frequent, if is, replace
PCB.
No
Inform the customer

service center.
61
2) Low Voltage Protection
Low voltage
protection
Yes
Yes
Reversed cooling and Adjust operation

heating mode
No
Yes
Compressor suction Open the suction
stop valve is not open. stop valve.
No
Yes
Blower stops rotating or rotates
in reversed direction when Inspect the blower or open
cooling; water pump is not open
or the flow insufficient when the water pump.
heating
No
Yes
Expansion valve cannot open Replace the

(broken capillary pipe or expansion valve.
leakage).
No
Yes
Inspect and maintain

Solenoid valve is not solenoid valve coil, valve
open. body and wiring.
No
Yes
Fin heat exchanger for cooling is
too dirty or aged; or, too heavy Clean heat exchanger.
encrustation in tube shell for
heating.
No
Yes
One way valve is Replace the
blocked. one way valve.
No
Yes
Water pipeline is not properly Adjust the water
designed. When it is closed at
the end, the water flow is pipeline system.
smaller.
No
Yes
Inspect and repair the leakage

Leakage of refrigerant point and then add refrigerant.
No
62
Yes
False alarm of controller Inspect whether it is frequent, if

is, replace PCB.
No
Inform the customer

service center.
3) Overheat Discharge Temperature Protection
Overheat discharge
temperature
Yes
Yes
Leakage of Inspect and repair the

leakage point and then add
refrigerant refrigerant.
No
Yes
Expansion valve can not open

(broken capillary pipe or leakage). Replace the expansion
valve.
Yes
One way valve is blocked. Replace the one way valve.
No
Yes
Wrong discharge temperature sensor
package is used (generally likely after Install correct temperature sensor
service of the unit). package
No
Yes

is, replace PCB.
No
Inform the customer service

center.
63
4) Compressor Overload Protection
Compressor
overload
Yes
Yes
Compressor protection module is in Replace the protection

trouble. module.
No

center.
5) Differential Pressure Alarm
Differential pressure
alarm
Yes
Yes
Reduce water flow for air conditioning
Ambient temperature in by around 60% and restart up the
winter is too low for starting machine, and then adjust it to the
heating. normal flow.
No
Yes
Pressure sensor is in Replace pressure sensor.
trouble.
No
Yes

is, replace PCB.
No

center.
64
6) Flow Switch Failure
Flow switch
failure
No
Yes
Water pump is not open. Open the water pump.
No
Yes
Water flow switch is not Install or Inspect the
installed or properly installation of water flow
installed. switch.
No
Yes
Water flow switch is in Service the water flow
trouble. switch.
No
Yes
False alarm of Inspect whether it is frequent, if
controller is, replace PCB.
No

center.
7) Power Failure
Power failure
Yes
Yes
Wrong power phase Adjust wiring.
sequence
No
Yes
Phase loss Inspect power

supply.
No
Yes
Failure of phase loss Replace phase loss

protection protection.
65
False alarm of Inspect whether it is frequent, if

controller is, replace PCB.

center.
2.2 Common Items and Tools for Unit Commissioning and Service
In order to realize immediate and effective commissioning, maintenance and service, the following tools
and items shall be available depending on units.
I. Common tools and applications:
1) External hex wrench, incl. adjustable and non-adjustable wrenches.
2) Internal hex wrench, comp. better
3) Pressure gauge, incl. gas/liquid gauge and connective gauge pipe, mainly for measuring
pressures of various locations in the system, monitoring the pressure during adding of
refrigerant, and functioning as a switch.
4) Refrigerant recycling machine, recycling refrigerant in the system.
5) Welding torch and relative equipment, welding torch, electrode (both common electrode and
high silver electrode), and scaling powder. For copper pipe with diameter above 9.52mm, larger
welding torch is required to facilitate even heating of the copper pipe.
6) As for vacuum pump and connection gauge pipe, if the vacuum pump connection is not
common for the general gauge pipe, the connection transition pipe must be prepared.
7) As for the refrigerant tank and connection, the refrigerant tank connection must be sound and
not damaged. In addition, it is important that the connection is common for related connection
gauge pipe.
8) Scissors, generally used for connecting gasket of relative connective parts of cutting unit.
9) Brush, used for cleaning dry filter and oil filter, etc.
10) Cutter, used for cutting copper pipe. Cutters with appropriate sizes shall be prepared for cutting
copper pipes of different sizes.
11) Pliers, auxiliary tool.
12) Mouth expander, consisting of bell mouth and mouth expansion.
13) Screwdriver, incl. slotted screwdriver and Phillips screwdriver, with complete sizes.
14) Leak detector (Leak detection powder is alternative if leak detector is not convenient for
carrying.)
15) Universal meter, for measuring current and voltage of the unit (incl. compressor, fan and other
parts), as well as coil resistances of compressor, fan and electronic expansion valve, line
connection and disconnection, etc.
16) Temperature detector, for measuring temperatures of various points in the system of the unit.
66
17) Pipe bender, for bending the copper pipe to certain degree, and frequently used for tubing of
pipeline in the unit.
18) Measuring tape, for measuring distance and length, etc.
II. Common items and application:
1) Copper nut, incl. metric and British systems, for making connective pipe with copper pipe.
2) Gasket cardboard, for making gasket seal as sealing is frequently required during maintenance
and service.
3) PTFE tape, for tightening nut, connection, etc.
4) Insulating tape
5) Tighten strip, for tightening wire or sensor, etc.
The above are only common tools and materials. Exceptional cases require particular
considerations.
2.3 List of Failures

Name of Source of
Failure Display Control Logic
Failure Failure
Flow switch failure Flow switch Flow switch The flow switch will be detected in 3 minutes of
failure pump running. If the flow switch of unit module is
off all the time for 5S successively, it shall be
reported for flow switch protection. Execute this
failure unit in the failure stop procedure; save the
content of failure. Confirm this failure manually
on touch screen as required after resetting the
flow switch (detection will not be carried out in
the period of stop, nor started until the pump
runs for 3 minutes)
Freeze protection Freeze alarm Antifreeze When leaving water temperature in a unit
Switch modular unit is less than or equal to 3℃ and the
mechanical antifreeze switch is switched off,
report freeze protection, immediately stop this
unit in the failure stop procedure, and save the
content of failure. Save the content of failure. Do
not switch on the unit modular unit (to be
detected during both stop and running) in
accordance with the conditions of temperature
and time until this failure is confirmed manually
on touch screen as required after failure is
eliminated.
High-pressure High-pressure High-pressure To be detected during both stop and running.
alarm alarm switch Switch off the high-pressure switch when
discharge pressure of the system is higher than
20Bar, report high-pressure protection, stop the
module immediately in the failure stop
procedure, and save the content of failure.
Reset will not be allowed until system pressure
is lower than the setting value after protection
occurs. Do not switch on the units in accordance
with the conditions of temperature and time until
this failure is confirmed manually on touch
screen as required after failure is eliminated.
67
Low-pressure alarm Low-pressure Low-pressure To be detected during both stop and running.
alarm switch Switch off the low-pressure switch when
discharge pressure of the system is lower than
1Bar, report low-pressure protection, stop the
module immediately in the failure stop
procedure, and save the content of failure.
Compressor Compressor Motor To be detected during both stop and running.
internal protection internal protector Switch off the protection switch in compressor in
protection the case of high temperature of compressor
winding, or high compressor discharge
temperature, or phase sequence error of
compressor power, or phase lack. Stop the units
immediately in the failure stop procedure and
save the content of failure. Do not switch on the
units in accordance with the conditions of
temperature and time until this failure is
confirmed manually on touch screen as required
after failure is eliminated.
Oil level protection Oil level Oil level To be continuously monitored prior to start,
protection switch report oil level protection in case of continuous
switch-off of oil level switch for 3S, and start of
compressor is not allowed; to be detected in
running, switch off the oil level switch in case of
continuous switch-off of oil level switch of
compressor for 60S during running of
compressor. Then report oil level switch
protection. Immediately stop the units in the
failure stop procedure, and save the content of
failure.
Oil differential Oil differential Oil differential To be detected in running, switch off the oil
pressure protection pressure pressure differential pressure switch when the difference
protection switch between oil pressure and discharge pressure of
compressor is higher than the setting value
during running of compressor. The indicator of
oil differential pressure switch in input interface
will be out. Do not switch on the units in
on touch screen as required after switch
resetting.
Contactor failure Contactor Contactor To be detected after start of master, report the
failure contactor failure in case of incorrect pull-in of
contactor. Do not switch on the units in
on touch screen as required after switch
resetting.
Compressor Compressor Compressor Report compressor overload protection when
overload overload overload relay the current value of unit compressor is greater
than the setting value and energy accumulated
to result in thermorelay trip. Stop the module
immediately in the failure stop procedure, and
save the content of failure. Do not switch on the
units in accordance with the conditions of
temperature and time until this failure is
confirmed manually on touch screen as required
after failure is eliminated.
68
Fans overload Fans overload Fans overload Report fans motor overload protection when the
relay current value of unit fans is greater than the
setting value and energy accumulated to result
in thermorelay trip. Stop the compressors and
fans (simultaneously) immediately for this
module, and save the content of failure. Do not
switch on the units in accordance with the
conditions of temperature and time until this
failure is confirmed manually on touch screen as
required after switch resetting.
Power Failure Power Failure Phase To be detected at any time, report power failure
sequence in cases of high / low voltage of power or phase
protector unbalance and phase lack. Failure will be
eliminated after power gets right. Notes: phase
lack / phase stagger of power will be detected
during both initial stage of power-on and unit
running.
High Fin temp. High Fin Fin temp. To be detected in running, the fin temperature of
temp. sensor the system is higher than 65℃, and the failure
record indicates that the fin temperature is too
high.
High Discharge High Discharge To be detected in running, the discharge

temp. Discharge temp. sensor temperature of the system is higher than 110℃,
temp. and the failure record indicates that the
discharge temperature is too high.
Leaving water Leaving water Leaving water Switch off compressors in case of failure of the
temp. sensor failure temp. sensor temp. sensor sensor itself. Switch-off of pump and fans will be
failure delayed. The failure indicator of display board
Entering water Entering Entering will be on, and a corresponding alarm mark will
temp. sensor failure water temp. water temp. be displayed in “Failure Query”. The
sensor failure sensor compressors will not be restarted until the failure
Fin temp. sensor Fin temp. Fin temp. of sensor is eliminated, and the failure signal
failure sensor failure sensor must be cleared manually, otherwise it cannot be
Ambient temp. Ambient Ambient cleared.
sensor failure temp. sensor temp. sensor
failure
Discharge temp. Discharge Discharge
sensor failure temp. sensor temp. sensor
failure
Suction temp. Suction temp. Suction temp.
sensor failure sensor failure sensor
Low-pressure alarm Low-pressure Low-pressure Do not restart the units until confirming manually
alarm switch on touch screen as required when the suction
pressure detected by the system is lower than
the setting value for continuously 1s.
High-pressure High-pressure High-pressure Do not restart the units until confirming manually
alarm alarm switch on touch screen as required when the discharge
pressure detected by the system is lower than
the setting value for continuously 1s.
Differential Differential Differential To be detected in running. Currently, there are

pressure alarm pressure pressure two modes, one is direct use of differential
alarm switch pressure switch, namely that when the
69
difference between high pressure and low
pressure of the system is smaller than the
setting value of 4Bar, the differential pressure
switch will be switched off, and the indicator of
differential pressure switch of input interface will
be out. The other is PLC calculation, namely that
an alarm will be given if the differential pressure
is smaller than 4Bar.
Low Suction Low Suction Low-pressure To be detected in running, report protection of

Pressure Pressure sensor too low suction pressure when the refrigeration
suction pressure is lower than 1Bar, and the
units will not be restarted until it is confirmed
manually on touch screen as required.
High Discharge High High-pressure To be detected in running, report protection of

Pressure Discharge sensor high discharge pressure when the discharge
Pressure pressure is higher than 20Bar, and the units will
not be restarted until it is confirmed manually on
touch screen as required.
Beyond the Beyond the Ambient The system will be automatically stopped when
operation range operation temp. sensor, the ambient temperature detected by the system
range entering water exceeds that set by the system for continuously
temp. sensor 5 minutes.
Mode water temp. Mode water Entering / Detect water temperature in the refrigeration
protection temp. Leaving water mode after start for 5 minutes, and report mode
protection temp. sensor water temp. protection when leaving water
temperature is not lower than entering water
temperature for continuously 5s.
EXV module failure EXV module EXV Control Start detection upon power-on of units, and
failure Module report immediately failure of EXV module when
the alarm output point of EXV control module is
switched off.
 Description: Communication failure (displayed on main page for units)

1） It is divided into internal communication failure and master-slave communication failure. A small
box indicating “Communication Failure” will appear on touch screen in case of internal
communication failure, and communication light “com” will flash at frequency varying from high
to low! Possible cause: poor contact of communication line.
2） Master-slave communication failure: inspect for error of wiring between master and slave, and
whether setting of station number is correct.
70
2.4 Installation/Removal and Service of Key Parts
1) Refrigerant Recycling and Adding
If transfer and recycling of refrigerant are
required during the maintenance and service, the
following items shall be carefully considered: The deformation and
failure of the oil
(1) If oil differential pressure alarm occurs in the
filtering net, need to
unit, the lubricating oil deteriorates and is be replaced
emulsified, or the unit is used for too long,
the compressor oil filter and tank shall be
cleaned, and the unit lubricating oil shall be
replaced. If the unit oil filter is deformed or damaged, it needs to be replaced.
Before replacing compressor oil filter, cleaning

compressor oil tank, replacing unit lubricating oil, oil level
switch, stop valve connected to the compressor, or other
parts, close the pressure-equalizing pipe stop valve of
discharge valve, suction valve and injection flow
expansion valve of the compressor, and discharge
Dirty block oil filtering
refrigerant in the chamber of the compressor. After the
net, need cleaning
replacement and cleaning are completed, pump vacuum
in to the compressor via vacuum pump, and after that,
negative pressure shall be kept. When the resumed vacuum in the unit meets the requirements, add part
of refrigerant, generally 5~10 kg, depending on particular situations.
(2) Before replacing electronic expansion valve of the system, pressure sensor sampling stop
valve, low pressure pipeline, etc. force the refrigerant in the liquid part of the system.
The particular steps are: (take careful consideration before continuing with the following steps)`
a Close the dry filter angle valve of the system.
b Start up the unit, and emergently stop the unit when the gas in the system is below 0.5bar.
c Close the liquid/air valve of the compressor.
d Discharge the residual refrigerant in the gas system.
e Carry on replacement of the parts of the system.
f After the replacement, extract vacuum in the gas part.
g After the vacuum extraction, keep the negative voltage until the resumed vacuum in the
unit meets the requirements.
h Open the angle valve of liquid system and compressor liquid/air stop valve to ensure the
loop of the entire system is unobstructed.
i Add proper amount of refrigerant, generally 5~10k.
(3) Before replacing dry filter core filter, directly close the angle valves at both ends to discharge
the residual refrigerant in the dry filter. After the replacement, fix the end cover tight, extract
71
vacuum, and then add 2~3kg refrigerant.
If only to clean the dry filter, but not to replace it, before removal of the filter, ensure that the
refrigerant in the dry filter is completely
discharged and the dry filter has remained not in
use for a time (to ensure the temperature of the
dry filter core is close to the ambient temperature)
so that the removed dry filter core with low
temperature would not cause the moisture in the
air to immediately reach to the dew point to
condense and absorb water. Protective measures
shall be taken to the removed filter to prevent it
from directly contacting with the air.
If the dry filter core is dirt or has absorbed too much moisture, it must be replaced with a dry
one.
During the operation, inspect whether the dry filter is blocked and whether the temperatures at
the dry filter inlet and outlet are close in normal conditions. If there is obvious temperature
difference (above 5℃) between the front and end of the filter, or even that frost exists at the end
of the filter, it is likely to block the dry filter.
If frost exists at
Seriously blocked dry the end, the dry
filter must be cleaned filter is seriously
or replaced. blocked.
If the temperature
difference between dry
filter front and end
exceeds 5℃, the dry
filter is likely blocked.
(4) If refrigerant is desired to be extracted for the complete machine, the refrigerant in the system
shall be transferred to particular refrigerant container via fluorine recycling machine.
72
2) Replacement of Compressor
(take careful consideration before continuing with the
following steps)
(1) Inspect the refrigerant system and various lines to
figure out the cause of burnout of the compressor
as far as possible.
(2) Recycle the refrigerant, and before that, prepare
relative equipment and tools, and especially keep
good ventilation condition in the working
environment.
(3) Remove the compressor from the system, and replace the dry filter.
(4) Inspect and clean the thermostatic expansion valve.
(5) Clean repeatedly the entire system with high pressure nitrogen.
(6) Extract vacuum in the system three times, and reduce the pressure of the system to an
appropriate value.
(7) Fill refrigerant in the system. Pay attention not to start up the unit until the filling amount is at
least 60% of the rated amount of the unit. This can be realized by lifting the refrigerant steel
cylinder and fill it in backward direction.
(8) Continue filling refrigerant after the start-up till it reaches the rated filling amount. It can be filled
in liquid if necessary. Ensure that the liquid filling point is before the vapor-liquid separator,
better at the inlet of the evaporator.
(9) Leave the system running for 48 h, extract a small amount of compressor oil, inspect the taste
and measure the acidity with PH paper. Replace the compressor oil if necessary.
(10) After step 9 is completed, leave the system running for another 48 h. If everything is normal,
change the dry filter to the original model for the unit.
(11) After the above steps, inspect the system again in two weeks to ensure the working conditions
and operation of the unit meet the requirements of the design.
3) Replacement of Shell and Tube Evaporator
(1) Inspect the water system and various lines for whether the evaporator is damaged.
(2) If it is damaged and needs replacement, disconnect the power supply of the unit and recycle
the refrigerant.
(3) Loosen the water inlet and outlet joints, separate the pipeline connected to the evaporator
through welding (different units have different heat exchange types; therefore, when welding
the connective pipeline, all connection locations shall be recorded. Wrong connected pipelines
will cause gas-cross in the system).
(4) Clean the system depending on particular situations.
(5) Loosen screws of fixing base of the evaporator, remove the shell and tube evaporator and
replace the heat exchanger with one of the same model, and connect the pipeline through
welding.
73
(6) Pay attention to nitrogen filled protection during welding.
(7) Keep the pressure of the system, extract vacuum, and refill refrigerant.
4) Replacement of Condenser
(1) Disconnect the power supply of the unit and recycle refrigerant.
(2) Remove the metal plate connected to the condenser and remove the guard of the condenser.
(3) Remove the parts of collector tube and gas-distributing
subassemblies connected to the condenser through welding.
Pay attention to the direction of the flame to prevent contact
with condenser fin and metal plate of the unit.
(4) Clean the system depending on particular situations.
(5) Loosen the fixing bolts connecting the condenser and metal
plate of the unit, remove and replace the condenser, and
connecting corresponding pipelines through welding.
(6) Pay attention to nitrogen filled protection during welding.
5) Replacement of Thermostatic Expansion Valve and Strainer
(1) Inspect the refrigerant system and various lines to figure out the cause of damage of the
expansion valve or strainer.
(2) If the expansion valve or strainer is to be replaced, disconnect the power supply of the unit and
recycle the refrigerant.
(3) Wrap the expansion valve body or strainer with wet cloth, remove the inlet and outlet tubes of
the expansion valve through welding, and then remove the expansion valve or strainer.
(4) Replace the thermostatic expansion valve or strainer with the one of the same model, wrap the
thermostatic expansion valve body or strainer with wet cloth again, and connect the inlet and
outlet tubes of the expansion valve through welding.
(5) Pay attention to nitrogen filled protection during welding. Besides, pay attention that no water
flows into the pipeline.
2.5 Precautions for Maintenance and Service

1) When the angel valve cores at both ends of the dry
filter are turned outward “left, two main pipelines 2
and 3 are connected and the needle valve
connector 1 is closed; when the valve cores are Left Right
turned inward “right, the needle valve connector 1
and the main pipeline 2 parallel to the angle valve
connector are connected, and the main pipeline 3
vertical to the needle valve connector is closed;
when the valve cores stop at the middle part, the
74
angle valve connector 1 and two main pipelines 2 and 3 are interconnected.
Ball Valve
When the ball valve core is turned
outward, the two main pipelines are
interconnected;
When the core is turned inward, the
two pipelines are not
interconnected
2) Each time when acing or cleaning the strainer, oil filter, stop valve, etc., inspect relative sealing
faces for leakage after filling of refrigerant.
3) Recycling of refrigerant is not part of the normal running, therefore, the protection settings of
the unit must be ensured valid, especially when the unit needs to operate. If the protection
switch is short connected due to protection failure, start-up is in principle not recommended.
4) The system of air cooling screws unit is generally complicated, and the flow line is long, if
replacement, cleaning and welding of parts at some area are required, close the valve as close
to the engaged area as possible, and minimize the volume of vacuum extraction.
5) If vacuum extraction is required for the complete machine, because of the complicated system,
it is better to divide the system into several parts for vacuum extraction, or extract vacuum at
several points in the system, generally 3 points at least, in addition, it is better to choose the
vacuum pump of larger model. If the vacuum pump is relatively small, sufficient time for vacuum
extraction shall be guaranteed.
6) During filling of refrigerant, valid metering device is required for accuracy of filling amount.
Empty the connective pipeline before filling refrigerant each time. Refrigerant pipe with reliable
quality shall be chosen to prevent accident during transfer or filling of refrigerant.
7) It is better to use filling machine to fill the refrigerant. If no filling machine is available, refrigerant
tank can be used to fill refrigerant directly. However, the pressure in the refrigerant tank is too
limited to fill the refrigerant required completely to the system. It is suggested to heat the
refrigerant tank in 40~50℃ water (heating temperature shall not be too high). When there is
60% of the rated amount of refrigerant in the system, start up the machine for filling. Fill
refrigerant at the gas side of the system, and control the flow of the refrigerant. Gas of
refrigerant is better. If it is liquid, it is better to be filled before the evaporator. If after the
evaporator, it shall be filled slowly and in small flow.
2.6 Training User Operator

The commissioning process includes training user operators in the following aspects:
1) Stress the safety in shutdown and operation processes.
2) Require the users to carefully read the operation manual of the unit.
75
Explain to the users that operation of the unit shall be carried out strictly as per the steps and
methods specified in the operation manual. If anyone has any problems about descriptions in
the manual, he shall enquire after-sale personnel or professionals in the factory and carry out
the operation only when he understands it. Any deviation in the installation of the unit from the
requirements in the manual shall be pointed out to the part responsible for installation, and the
after-sale personnel or professionals in the factory will determine whether change is necessary.
3) Short-connection is forbidden when all protection functions of the unit are normal. Ensure all
protection functions are available and reliable.
Various protection switches in the unit are for safety of the unit or user, and are not permitted to
be short connected in principle. If short-connection is required for commissioning, the operation
shall be done by the after-sale personnel or professionals in the factory on site. After the
commissioning, connect the protection switches to the system before starting up the unit for
long-time running.
4) Open the water pump and wait until the water flow is stable before starting up the master
compressor. For shutdown, the water pump must be closed in a delayed time. It is not allowed
to forcibly close the water pump when the master compressor is still running. If the water pump
fails, and the flow switch does not jump, the unit must be emergently shut down.
5) The unit must be disconnected from the power supply during inspection or replacement of the
lines of the unit.
If it is required to tighten the line bank screw or replacing the wire and element in the electrical
cabinet during commissioning and maintenance, it shall be down when the power supply is
disconnected. Similar operations by the user in later maintenance and service shall also be
done when the power supply is disconnected.
6) The non-user parameters in the touch screen of the unit and electronic expansion valve control
module are forbidden to be changed.
The non-user parameters in the touch screen of the unit and electronic expansion valve control
module are directly related to the performance and reliability of the unit, and are not allowed to
be changed in principle. Even if it is required to adjust some parameters due to special local
climate, it shall be done by or under the instructions of after-sale personnel or professionals in
the factory.
7) If any exceptional case occurs to the unit, it is forbidden to forcibly start up the unit unless under
the instructions of professionals.
Exceptional temperature, pressure, sound, or vibration, etc. of the unit during the running shall
be clearly recorded in details, and reported to after-sale personnel or professionals in the
factory. It is forbidden to forcibly start up the unit unless permitted.
76
V. Control Logic
1. Start (Stop) Logic

1.1 Start Logic
1) Cooling Start:
Step A: Power-on
Complete
initialization
Step B: Select cooling running

mode, Start signal
Switch on pump
Detect water temperature every
other temperature control cycle
Step C:
Idle status Detect water
energy temperature, see
adjustment NO whether load is
YES
Clear failure NO Step D:

until no unit Whether there is any
without failure unit without failure
protection protection
YES
NO Whether there is any modular

unit with compressor oil
heating time and switch on-off
interval meeting Start condition
YES
Select system A of the shortest

compressor running time
according to length of
compressor running time
77
Power-on 25% solenoid valve

system A compressor
Star start of system A compressor, intermittent

conduction of oil-supply solenoid valve
Judge the number of adjustable (10S.10S, synchronized with
operating fan as compressor, stop compressor, intermittent
required according to conduction of oil-supply solenoid valve
the discharge pressure adjustable stopped) for Bitzer compressor,
switch on fan based on discharge pressure
Star delta switch, system

A compressor
Power-on 50% solenoid valve,

power-off 25% solenoid valve,
system A compressor
Energy adjustment
execution
Start end system A
Execute step B at the interval of 120 s for other modular units.

2) Start after cooling energy adjustment Stop:
When total entering water temperature is detected to be within the start reset temperature
range after energy adjustment Stop of all modules, the first unit module meeting the Start
condition will be executed from step B, and other modular units will be executed from step A to
start up at the interval of 120 s.
Only some of modular units stopped adjustably, the units that have been stopped will be
executed from step A, and each module will be started at the interval of 120S.
Description:
1. Double-head Start Mode:
According to the running time of compressors, the unit of shorter running time will be started
prior to the other in the case that both compressors meet the starting condition, and No 1 head
78
If water temperature has been within loading area after the head started prior to the other, the
other will be started in two minutes. If water temperature has been (or had been) immerged in
loading area in two minutes, the other head will not be started until the head started prior to the
other has been started and loaded to 100% in case that further loading is required for the unit
according to the energy adjustment process.
2. Multi-Connected Start Mode:
Water pump starts to run upon point start of units, and the duration of switching on the water
pump is from 3 to 5 minutes. The units will be converted into idle mode upon switching on the
water pump, and then attempt will be made to switching on the compressor.
The running times of all jointly-controlled units will be sequenced in case of multi-connection
provided that the condition for switching on the compressor is satisfied. The unit of shorter
running time will be started prior to the other when both units meet the Start condition, and the
unit of smaller station number will be switched on prior to the other in the case of identical
running time.
Double-Compressor running time: the running time of one head of shorter running time than
that of the other will be taken as the reference during loading, and the running time of the other
head will be directly taken as the reference if one head does not meet the starting condition; the
running time of one head of longer running time than that of the other will be taken as the
reference during unloading, and the running time of the other head will be directly taken as the
reference if one head does not meet the unloading condition.
When no unit running has been started, the jointly-controlled units will be started at the interval
of 2 minutes for each in the Start order with water temperature is in the loading area, (to be
executed as per the above double-head single-unit mode, with double-head treated as one
unit), and energy adjustment will be executed individually by the unit that has been started;
when water temperature is not in the loading area, a single unit will no longer execute energy
adjustment individually, nor the unit that has not been switched on will be switched on at the
interval of two minutes, and the complete machine will start to run in accordance with the
normal process of energy adjustment.
1.2 Stop Logic

1) Normal Stop
Shut-down signal
NO Step E: Execute step E at

Whether the system the interval of 30S
has the shortest for other modular
running time to satisfy units not stop.
the compressor
YES 79
Select system A of the

longest compressor
running time
Current compressor Current compressor running at

running at 75％ (Load judgment) 50％
Current compressor
running at 100％
One temperature control cycle
One temperature control cycle

Power-on 50%
solenoid valve, system
A compressor
Power-on 25%
A compressor
Power-off main
contactor, system A
compressor
Shut-down all fans of

system A compressor
Step F:
Power-on 25%
solenoid valve,
system A compressor
Shut-down all modular

units
Switch off water pump,

shut-down ended
80
When all modules are in the energy adjustment idle status, 3 minutes will be delayed to switch off
water pump after Stop signal is received.
2) Energy adjustment Stop
All unit module

compressors run after
unloaded to 50%
Detect water temperature every
other temperature control cycle
Other modular
Remain in current NO Whether water units not stop
status temp. is in executed this
unloaded area step every other
temperature
YES
NO
Whether there is
any modular unit
satisfying the
shortest
compressor running
YES
Select system A of the

longest compressor
running time
Power-on 25%
A compressor
Power-off main
contactor, system A
compressor
Stop all fans of system

A compressor
Power-off 25%
A compressor
81
3) Downtime
Failure signal detected
Power-off the main

contactor, compressor of
failure unit, power-on 25%
solenoid valve, and
power-off load solenoid
valve being powered on
Power-off all fans of

this failure module
Power-off 25%
solenoid valve of this
failure module
Water pump will stop running after Stop of the last failure module for 3 minutes when any non-resettable
failure not resulting from flow switch occur in all modular units.
Description:
1. Double-Compressor Stop Mode:
When the units meet the Stop condition after point Stop of units,
When both compressors are running with regard to the double-head mode, the unit of longer
running time will be stopped prior to the other, and the other stopped in 30S provided both units
meet the Stop condition.
The compressors will be unloaded and stopped in accordance with the step by step unloading
mode. For example, with regard to the compressor running at 75%, when the condition for
compressor Stop is satisfied after point Stop, the units will firstly be unloaded to 50% then
unloaded to 25% to run for a period of time followed by Stop of compressors.
25% solenoid valve will continue to be powered on for a period of time to facilitate resetting of
the solenoid valve when both compressors are switched off.
The whole process of Stop will be completed upon running of water pump for 3 to 5 minutes
after the compressors are switched off.
2. Multi-Connected Stop Mode：

The units will meet the Stop conditions after point Stop,
The unit of longer running time will be stopped prior to others with regard to multi-connected
82
units sequenced in accordance with running time, and the unit of greater station number will be
stopped prior to others when the units are of the same running time.
The compressors will be unloaded and stopped in accordance with the step by step unloading
mode. For example, with regard to the compressor running at 75%, when the condition for
compressor Stop is satisfied after point Stop, the units will firstly be unloaded to 50% then
unloaded to 25% to run for a period of time followed by Stop of compressors.
25% solenoid valve will continue to be powered on for a period of time to facilitate resetting of
the solenoid valve when both compressors are switched off.
The entire Stop process will be completed upon running of water pump for 3 to 5 minutes after
the compressors are switched off.
Remarks:
① The units Stop command must be executed whenever there is a Stop signal in any case
(except the defrosting process, the user must be prompted whenever there is a Stop signal in
the process of unit defrosting, Stop will not be allowed until the defrosting process is completed
followed by the Stop sequence of the last module) after the compressors meet the requirement
of limitation of the shortest running time. Any controller which has not been output, independent
of the Stop process, shall not be output once again.
② The Stop signal exists when some modules among interconnected modules do not meet the
Stop condition. Unit modules which meet the Stop condition will be stopped as per the normal
Stop procedure, and those which fail to meet the Stop condition will not be stopped in sequence
after entering the normal Stop procedure until they meet the Stop condition. 3 minutes will be
delayed to switch off water pump after Stop of compressors of all unit interconnected modules.
③ The Stop signal exists when all modules among interconnected modules fail to meet the Stop
condition, with output displayed in the table of unit running status as required, and Stop will not
be allowed until the Stop condition is satisfied.
④ The compressors will not be stopped with the variation of water temperature within the shortest
running time once the modular unit is started, except for failure protection.
⑤ The compressors will not be started up with any Start command at the shortest Stop interval or
between two Starts once the modular unit is stopped, and they will not be started up for
operation until the shortest Stop interval and the interval between two Starts of compressors.
2. Energy Adjustment Logic

Energy adjustment may be controlled by either entering water temperature or leaving water
temperature in case of operation of single-module unit, and it can only be controlled by entering
water temperature in case of multi-module interconnection.
Compressor Capacity Adjustment
The capacity output of the unit is determined by the valid length of slide valve which is controlled by
3 solenoid valves. The control system cycles compressors, loaders, and minimum load control
83
valves to maintain the user configured leaving (or entering) chilled water temperature set point.
Temperature sensors transfer temperature signals to PLC which will calculate the optimum time to
add or subtract capacity stages. Special algorithm programmed in PLC will try to maintain the
Control Point at the desired set point.
 4-stage control (50%~100%)
The 4-step capacity control system is made of one slider, three NC solenoid valves and one piston
with adjustable range of 25%, 50%, 75% and 100%. The principle of capacity control is by moving
the slider to allow partial refrigerant to bypass back to the intake and regulate the refrigerant flow.
Solenoid valve activating table of four-stage capacity control
SV1 SV2 SV3

SV
(NC) (NC) (NC)
Status
100% OFF OFF OFF
75% OFF OFF ON
50% OFF ON OFF
25%(startup) ON OFF OFF
ON: energize, OFF: de-energize
Startup: 25% loading
For easier startup of compressor, the loading must be minimized. Therefore, SV1 is energized to
bypass oil to the low-pressure side directly. The slider does not move and keep the maximum
opening in suction end to bypass the refrigerant. After the completion of startup the compressor then
can increase loading gradually by de-energizing the SV1 solenoid valve. It is recommended to run
compressor at 25% loading for about 30 seconds before starting to increase loading.
Partial load: 50% Operation
With the same principle as stated in 25% loading, SV2 is energized and others are de-energized to
achieve 50% loading.
Partial load：75% Operation
84
Receiving a feedback from system demanding for lower capacity, the SV3 is energized to allow oil to
flow back to the low-pressure side through the valve channel. The piston returns to the outlet of SV3
oil passage and the slide block moves to let part refrigerant flow back to the low-pressure side
through bypass opening. This action would reduce the discharge volume and make the compressor
operating at 75% loading
Full load: 100% operation
After the completion of startup, SV1, SV2 and SV3 are de-energized and oil flows straight to cylinder
and pushes piston forward, driving the slider to gradually reduce bypass opening. When the
opening is closed completely, the compressor is running at 100% loading.
Control of Cooling Energy Adjustment

The total entering water temperature may be set as Ts (Ts settable) with the touch screen, the set
total entering water temperature Ts＝12℃ as default (settable range varying from 12 to 15℃), and
the total entering water temperature is Tin.
Start Reset Temperature Tin≥ T△（T△≥ (Ts+1) The temperature control cycle for
Loading Area Tin≥Ts+1 temperature judgment in the table is
Fuzzy Loading Area Ts+0.5＜Tin＜Ts+1 60S (settable).
Stable Area Ts-1≤Tin≤Ts+0.5 In the case of judgment of the
Unloading Area Ts-2＜Tin≤Ts-1 temperature rise trend (compared
Stop Area Tin≤Ts-2 with that of the previous temperature

control cycle) of a temperature
control cycle for the fuzzy loading area, if temperature rises, loading will be executed, otherwise no
action is executed. When all units of interconnected modules having been put into operation are
loaded to 100%, entering water temperature still remains in the fuzzy loading area without starting
the module to be started, and the module to be started will not be put into operation until entering
water temperature is positioned in the loading area.
Compressors and fans of modules will be stopped one by one in the energy adjustment Stop
procedure after entering water temperature enters the Stop area and compressors of unit modules
meet the requirement of the shortest running time. Then the units enter the energy adjustment idle
status.
Loading will be executed when entering water temperature is positioned in the loading area or the
fuzzy loading area, entering water temperature in a lower energy level will be firstly loaded, and for
entering water temperatures in the same energy level, those of shorter running time will be firstly
loaded. (Running times are compared in hours, the same hereinafter). When running times are
identical, those of smaller address number will be firstly loaded.
Unloading will be executed when entering water temperature is positioned in the unloading area,
those in a higher energy level will be firstly unloaded, and those of longer running time will be firstly
loaded when energy levels are identical.
85
The module will remain in the status after unloaded to 50% load, and the other module of longer
running time will be unloaded if unloading is still required. All modules running in an interconnected
mode will be unloaded to 50% load, and modules of longer running time will be firstly stopped if
entering water temperature needs to be unloaded.
Compressors and fans will not be started once again to run when entering water temperature meet
the reset Start condition while meeting the shortest Stop time of compressors.
3. Fan Control Logic

The number of operating fan as required is according to the discharge pressure. For example, for
LSBLGW500/C, there are 8 fans, divided into 5 groups. Opening condition as follow:
4. Oil heater control Logic

In unit shutdown period, oil heater is energized to keep normal oil temperature. When unit starts, it is
turned off.
Oil heating time limits:
 When cooling water inlet temperature >= 35°C (real time value), oil heating time for first startup
is 0.5h. If power down happens during operation and downtime is less than 8hrs, no heating
time delay is needed when unit restarts. If it exceeds 8hrs, 0.5h heating time is need.
is 1h. If power down happens during operation and downtime is less than 5hrs, no heating time
delay is needed when unit restarts. If it exceeds 5hrs, 1h heating time is need.
is 2hrs. If power down happens during operation and downtime is less than 3hrs, no heating
time delay is needed when unit restarts. If it exceeds 3hrs, 0.5h heating time is need. If it
exceeds 5hrs, 2hrs heating time is need.
86
is 4hrs. If power down happens during operation and downtime is less than 1h, no heating time
delay is needed when unit restarts. If it exceeds 1h, 2hrs heating time is need. If it exceeds 5hrs,
3hrs heating time is need. If it exceeds 8hrs, 4hrs heating time is need.
 When cooling water inlet temperature < 20°C (real time value), oil heating time for first startup is
8hrs. If power down happens during operation and downtime is less than 1h, no heating time
delay is needed when unit restarts. If it exceeds 1h, 3hrs heating time is need. If it exceeds 5hrs,
5hrs heating time is need. If it exceeds 8hrs, 8hrs heating time is need.
5. EXV operation& wiring

User interface consists of five components of the LED display operating status, the table below:
LED Light Extinguish Flicker

Can be
Not Communication
NET connected to
connected failure
the network
Open the
OPEN - Disable the drive
valve
Close the
CLOSE - Disable the drive
valve
Activate the
- -
alarm
The drive is
not connected
Drive power -
to power
supply
 Display and keypad

Graphical display with two kinds of system variables, the drive control of the state, protection
function is activated, and the alarm and relay output status
87
Note:
Control Type of protection
state running 1 Display first kinds of variables
Low superheat 2 Display second kinds of variables
ON Run LowSH
protection 3 Relay output status
Low evaporation
OFF Standby LOP temperature 4 Alarm
protection 5 Start of the protection
High evaporation
6 Control state
POS Locate MOP temperature
protection
High condensing
WAIT Wait HiTcond temperature
protection
CLOSE Close
Keypad:
Button Function
Open the display screen, enter the password to enter the programming
Prg
mode
• In the alarm state, the display alerts the queue;
• When the "producer" level under the rolling parameters, the display
shows the interface
• To exit the programming (maintenance / producer) and display mode;
Esc
• set a parameter, the exit without saving changes
• Display screen navigation;
UP/DOWN • Increase / decrease the value
• from the parameter setting mode, the display switches to
Enter • Confirm the list of parameters and return the value
 General wiring diagram
Terminal Explanation
G\G0 Power supply
VABT Emergency Power Supply
Functional ground
1,2,3,4 Stepper motor power supply
COM1,NO1 Alarm Relay
GND Signal Ground
VREF Sensor power supply
Sensor 1 (pressure) or an external
S1
signal 4 to 20mA
Sensor 2 (temperature) or 0 to 10V
S2
external signal
S3 Sensor 3 (pressure)
S4 Sensor 4 (temperature)
88
Terminal Explanation Terminal Explanation
Connection tLAN, pLAN, RS485, Modbus ®
DI1 Digital input 1
terminal
DI2 Digital input 2 Connection pLAN, RS485, Modbus ® terminal
Connection tLAN, pLAN, Service port, after removal of the cover need to
aa
RS485, Modbus ® terminal be connected LED
1 Green
2 yellow
3 Brown
4 white
5 sets of personal computers
6 USB / tLAN converter
7 Adapter
ratio of pressure sensor -
8
evaporation pressure
9 NTC suction temperature
10 start-controlled digital input 1
11 free contacts (up to 230Vac)
12 solenoid valve
13 warning signs
89
Appendix 1: R134a saturation temperature - pressure corresponding tables
R134a saturation temperature - pressure corresponding tables
℃ KPa ℃ KPa ℃ KPa ℃ KPa
-15 164 7 375 29 748 51 1351
-14 171 8 388 30 770 52 1385
-13 178 9 401 31 793 53 1420
-12 185 10 415 32 815 54 1455
-11 193 11 429 33 839 55 1492
-10 201 12 443 34 863 56 1528
-9 209 13 458 35 887 57 1566
-8 217 14 473 36 912 58 1604
-7 225 15 488 37 937 59 1642
-6 234 16 504 38 963 60 1682
-5 243 17 521 39 990 61 1722
-4 253 18 537 40 1017 62 1763
-3 262 19 554 41 1044 63 1804
-2 272 20 572 42 1072 64 1847
-1 282 21 590 43 1101 65 1890
0 293 22 608 44 1130 66 1934
1 304 23 627 45 1160 67 1978
2 315 24 646 46 1190 68 2024
3 326 25 665 47 1221 69 2070
4 338 26 685 48 1253 70 2117
5 350 27 706 49 1285 71 2165
6 362 28 727 50 1318 72 2213
Note: this table of pressure values for absolute pressure value, the pressure value ( unit touch screen
display value ) for the vast pressure value and the local atmospheric pressure difference.
Appendix 2: the flow chart of the system
90
Appendix 2: system working principle map:
LSBLGW380/C，LSBLGW500/C
91
92
93
94
Appendix 3: capacity table
Ambient temperature
15 20 25 30 35 40 43
Outlet
Model Cooling Power Cooling Power Cooling Power Cooling Power Cooling Power Cooling Power Cooling Power
Temp.
Capacity Input Capacity Input Capacity Input Capacity Input Capacity Input Capacity Input Capacity Input
/kw /kw /kw /kw /kw /kw /kw /kw /kw /kw /kw /kw /kw /kw
5 418.0 93.0 397.3 101.4 380.6 108.1 362.3 115.7 349.8 120.8 324.3 130.8 310.1 137.1
6 436.0 94.5 414.3 103.0 396.6 109.7 376.9 117.3 362.5 122.4 337.5 132.6 322.0 138.8
7 453.9 96.0 431.3 104.5 412.6 111.3 392.0 119.0 376.0 124.0 350.6 134.3 334.5 140.6
8 471.9 97.5 448.3 106.1 428.6 112.9 407.0 120.6 390.7 125.8 363.8 136.1 347.1 142.4
9 489.8 99.0 465.3 107.6 444.7 114.5 422.1 122.3 404.8 127.5 376.9 137.8 359.7 144.2
380 10 507.8 100.4 482.3 109.2 460.7 116.1 437.2 123.9 417.2 129.0 390.1 139.6 370.7 145.7
11 525.8 101.9 499.3 110.7 476.7 117.7 452.2 125.6 433.1 131.0 403.2 141.4 384.9 147.7
12 543.7 103.4 516.3 112.2 492.8 119.3 467.3 127.2 447.2 132.7 416.3 143.1 397.5 149.5
13 561.7 104.9 533.3 113.8 508.8 120.9 482.3 128.9 461.3 134.4 429.5 144.9 410.0 151.3
14 579.6 106.4 550.3 115.3 524.8 122.5 497.4 130.6 475.4 136.1 442.6 146.7 422.6 153.1
15 597.6 107.9 567.3 116.9 540.8 124.1 512.5 132.2 490.5 138.0 455.8 148.4 436.0 155.0
5 527.4 120.7 504.5 131.3 489.1 139.4 470.0 148.9 461.8 154.7 431.7 167.6 413.1 175.3
6 552.2 122.1 527.8 132.8 510.5 141.2 489.6 150.7 478.4 156.8 447.9 169.8 428.7 177.8
7 576.9 123.4 551.1 134.3 532.3 143.0 509.9 152.7 496.0 159.0 465.3 172.3 445.4 180.3
8 601.6 124.7 574.5 135.8 554.0 144.7 530.3 154.7 515.6 161.5 482.7 174.7 462.2 182.8
9 626.3 126.0 597.8 137.3 575.8 146.5 550.6 156.7 534.3 163.8 500.1 177.2 478.9 185.3
500 10 651.0 127.3 621.2 138.8 597.6 148.3 570.9 158.7 550.5 165.8 517.5 179.6 493.2 187.5
11 675.7 128.7 644.5 140.3 619.4 150.0 591.2 160.7 571.5 168.5 535.0 182.1 512.4 190.4
12 700.4 130.0 667.8 141.8 641.2 151.8 611.6 162.7 590.2 170.8 552.4 184.5 529.2 192.9
13 725.0 131.3 691.2 143.3 663.0 153.6 631.9 164.7 608.8 173.2 569.8 187.0 545.9 195.4
14 749.7 132.6 714.5 144.8 684.7 155.3 652.2 166.7 627.4 175.5 587.2 189.4 562.6 197.9
15 774.3 133.9 737.9 146.4 706.9 157.1 673.3 168.8 647.5 178.0 605.9 192.1 580.6 200.6
95
Ambient temperature
15 20 25 30 35 40 43
Outlet
Temp.
5 634.0 133.6 609.2 147.7 591.0 159.7 569.4 172.7 557.4 182.6 526.4 198.7 507.2 208.6
6 653.3 135.9 627.9 150.1 609.5 162.0 587.5 175.1 575.2 184.8 543.7 201.2 524.0 211.1
7 674.0 138.5 647.9 152.8 629.3 164.6 606.9 177.6 594.0 187.0 562.2 203.7 541.8 213.8
8 694.6 141.2 667.9 155.5 649.1 167.2 626.3 180.2 614.5 189.5 580.7 206.3 559.7 216.5
9 715.3 143.8 687.9 158.2 668.9 169.8 645.7 182.8 634.1 191.9 599.3 208.8 577.5 219.2
600 10 735.9 146.4 705.4 160.2 688.7 172.4 665.1 185.4 651.3 194.0 617.8 211.4 593.2 221.6
11 756.6 149.1 727.9 163.5 708.5 175.0 684.4 188.0 673.4 196.6 636.3 213.9 613.2 224.5
12 777.2 151.7 747.9 166.2 728.3 177.6 703.8 190.6 693.1 199.0 654.9 216.5 631.1 227.2
13 797.9 154.3 767.9 168.9 748.1 180.2 723.2 193.1 712.8 201.3 673.4 219.0 648.9 229.9
14 818.5 157.0 787.9 171.6 767.9 182.8 742.6 195.7 732.4 203.7 691.9 221.6 666.8 232.6
15 840.6 159.9 809.2 174.6 789.0 185.4 763.2 198.5 753.5 206.2 711.7 224.3 685.7 235.4
5 767.1 177.6 744.1 189.9 717.3 204.2 690.5 218.7 676.9 227.9 636.8 247.1 611.2 259.2
6 790.8 180.9 767.3 193.6 739.5 207.8 711.8 222.1 697.9 230.8 657.0 250.3 630.8 262.6
7 815.4 184.8 791.4 197.4 763.2 211.5 735.1 225.6 720.0 234.0 678.5 253.9 650.9 266.3
8 840.0 188.6 815.5 201.1 787.0 215.1 758.4 229.1 744.1 237.6 699.9 257.5 671.1 269.9
9 864.6 192.4 839.6 204.9 810.7 218.7 781.8 232.6 767.3 241.0 721.3 261.2 691.2 273.5
720 10 887.3 195.2 863.7 208.6 834.4 222.3 805.1 236.1 787.8 243.7 742.8 264.8 709.9 276.7
11 913.7 200.1 887.8 212.4 858.1 226.0 828.5 239.6 813.5 247.8 764.2 268.4 731.4 280.8
12 938.3 203.9 911.9 216.1 881.8 229.6 851.8 243.1 836.6 251.3 785.7 272.1 751.5 284.5
13 962.9 207.7 936.0 219.9 905.6 233.2 875.1 246.6 859.7 254.7 807.1 275.7 772.5 288.4
14 987.5 211.6 960.1 223.6 929.3 236.8 898.5 250.1 882.8 258.1 828.5 279.4 751.7 268.9
15 1013.0 215.9 985.2 227.3 954.5 240.5 923.8 253.7 907.4 261.9 851.2 283.4 773.6 272.9
96
Ambient temperature
15 20 25 30 35 40 43
Outlet
Temp.
5 953.4 216.6 910.2 235.5 878.1 249.9 840.4 267.1 818.7 277.7 765.1 300.7 732.2 314.9
6 995.4 218.4 949.8 236.9 914.9 252.9 874.6 270.2 848.6 281.2 794.1 304.7 758.6 318.8
7 1037.3 220.8 989.4 239.5 951.9 256.0 909.2 273.6 880.0 285.0 823.8 308.8 787.0 323.0
8 1079.1 223.2 1028.9 242.2 988.8 259.1 943.7 277.0 912.1 289.1 853.4 313.0 815.4 327.2
9 1121.0 225.5 1068.4 244.8 1025.8 262.2 978.2 280.5 943.9 293.1 883.0 317.1 843.7 331.4
880 10 1162.9 227.9 1107.9 247.5 1062.8 265.2 1012.7 283.9 975.7 297.1 912.7 321.2 872.1 335.6
11 1204.7 230.3 1147.5 250.2 1099.7 268.3 1047.3 287.3 1007.4 301.0 942.3 325.3 900.5 339.8
12 1246.6 232.7 1187.0 252.8 1136.7 271.4 1081.8 290.7 1039.2 305.0 971.9 329.4 928.8 344.0
13 1288.4 235.0 1226.5 255.5 1173.7 274.4 1116.3 294.1 1071.0 308.9 1001.5 333.6 957.2 348.2
14 1330.3 237.4 1266.1 258.1 1210.7 277.5 1150.8 297.6 1102.7 312.9 1031.2 337.7 985.6 352.4
15 1372.0 240.3 1305.5 262.1 1247.8 280.6 1185.7 301.3 1136.3 317.2 1061.4 341.9 1015.9 357.0
5 1047.0 244.0 1002.7 264.9 975.8 280.5 940.2 298.8 929.6 309.6 869.0 335.4 831.3 351.3
6 1107.1 246.2 1058.0 267.4 1024.5 283.6 983.2 302.4 961.8 313.7 900.6 339.9 861.2 355.8
7 1156.0 248.3 1104.1 269.9 1067.2 286.8 1022.8 306.1 996.0 318.0 934.0 344.6 893.4 360.7
8 1204.9 250.3 1150.3 272.4 1110.0 290.0 1062.5 309.8 1033.4 322.8 967.5 349.4 925.5 365.5
9 1253.8 252.4 1196.4 274.9 1152.7 293.1 1102.1 313.5 1069.2 327.3 1001.0 354.2 957.7 370.4
1000 10 1302.8 254.5 1260.9 277.5 1195.5 296.3 1141.8 317.2 1105.0 331.9 1034.4 358.9 985.3 374.5
11 1351.7 256.6 1288.6 280.0 1238.2 299.5 1181.4 320.9 1140.9 336.4 1067.9 363.7 1022.0 380.2
12 1400.6 258.7 1334.8 282.5 1280.9 302.6 1221.1 324.6 1176.7 341.0 1101.4 368.4 1054.1 385.0
13 1449.6 260.8 1380.9 285.0 1323.7 305.8 1260.7 328.3 1212.5 345.5 1134.8 373.2 1086.3 389.9
14 1498.5 262.9 1427.0 287.5 1366.4 308.9 1300.4 331.9 1248.3 350.1 1168.3 378.0 1118.4 394.8
15 1536.3 264.9 1464.0 290.1 1403.2 312.1 1336.7 335.8 1286.7 355.0 1203.6 383.0 1152.8 400.1
97
Ambient temperature
15 20 25 30 35 40 43
Outlet
Temp.
5 1316.6 271.8 1260.9 299.9 1216.0 323.3 1165.7 350.3 1131.1 370.7 1065.1 402.6 1024.8 422.0
6 1367.3 274.4 1308.5 303.0 1259.8 327.2 1206.0 354.6 1166.1 375.7 1098.5 408.1 1056.8 427.7
7 1417.8 276.9 1356.1 306.1 1304.3 331.0 1247.5 359.1 1203.0 381.0 1134.0 413.9 1090.7 433.7
8 1468.3 279.4 1403.7 309.2 1348.8 334.9 1289.0 363.6 1242.7 386.8 1169.5 419.7 1124.5 439.7
9 1518.8 282.0 1451.3 312.3 1393.3 338.7 1330.5 368.1 1281.0 392.3 1205.0 425.6 1158.4 445.8
1200 10 1569.3 284.5 1498.9 315.4 1437.8 342.6 1372.0 372.7 1315.1 397.1 1240.5 431.4 1188.5 451.1
11 1619.8 287.0 1546.5 318.4 1482.3 346.5 1413.5 377.2 1357.6 403.3 1276.0 437.3 1226.2 457.8
12 1670.3 289.6 1594.1 321.5 1526.8 350.3 1455.0 381.7 1395.8 408.9 1311.5 443.1 1260.0 463.8
13 1720.8 292.1 1641.7 324.6 1571.3 354.2 1496.5 386.2 1434.1 414.4 1347.0 449.0 1293.9 469.9
14 1771.3 294.7 1689.3 327.7 1615.8 358.0 1538.0 390.8 1472.4 419.9 1382.5 454.8 1327.8 475.9
15 1821.6 297.1 1736.9 330.8 1661.0 361.9 1580.7 395.5 1513.1 425.8 1420.0 461.0 1363.6 482.3
5 1516.8 353.6 1469.6 378.0 1416.0 406.7 1362.3 435.6 1331.3 453.7 1255.0 492.3 1206.7 516.6
6 1562.6 360.0 1515.5 385.4 1460.4 413.8 1405.3 442.3 1375.8 459.7 1296.5 498.7 1245.4 523.4
7 1610.9 367.5 1563.1 392.7 1507.4 421.0 1451.6 449.2 1419.0 466.0 1339.2 505.9 1285.2 530.6
8 1659.2 375.0 1610.7 400.1 1554.3 428.1 1497.9 456.1 1468.8 473.3 1381.8 513.1 1325.0 537.8
9 1707.6 382.5 1658.3 407.5 1601.3 435.3 1544.2 463.0 1515.3 480.2 1424.4 520.3 1364.7 545.0
1420 10 1755.9 390.0 1705.9 414.9 1648.2 442.4 1590.5 469.9 1561.8 487.0 1467.1 527.5 1404.5 552.1
11 1804.2 397.5 1753.5 422.2 1695.2 449.6 1636.7 476.9 1608.3 493.8 1509.7 534.7 1444.2 559.3
12 1852.6 405.0 1801.1 429.6 1742.1 456.7 1683.0 483.8 1654.8 500.7 1552.3 541.9 1484.0 566.5
13 1900.9 412.5 1848.7 437.0 1789.1 463.8 1729.3 490.7 1701.3 507.5 1595.0 549.1 1525.4 574.3
14 1949.2 420.0 1896.3 444.3 1836.0 471.0 1775.6 497.6 1747.8 514.3 1637.6 556.3 1491.7 535.5
15 2000.1 428.5 1945.7 451.7 1885.5 478.1 1825.3 504.8 1794.5 521.6 1681.4 564.3 1538.1 543.9
98
3P+N+PE 50Hz 380-400V
N
N X1 X2 X2 2/1B
L1 1L1 X1 L1 2/1B
L2 1L2
L3 1L3
PE 1QF 261A
3QF 16A
3*1.5mm+1*1.5mm, 11.6A
2QF 1A
0.75mm,0.1A
KR1 L1 L2 L3 125
127
KM1 KM2 KM3 KM4 KM5 KM6
16 15 18 TA1 TA2
FR U11V11W11 U21V21W21 U31V31W31 U41V41W41 U51V51W51 U61V61W61
2 32 FR1 FR2 FR3 FR4 FR5 FR6
U1 V1 W1 PE U2 V2 W2 PE U3 V3 W3 PE U4 V4 W4 PE U5 V5 W5 PE U6 V6 W6 PE
123
4/9B 4/9C
KM11 KM12
3P 50Hz 380-400V 2.2kW 5.8A
3*70mm+1*35mm,132A 3*70mm
W
V
U
Air-cooled screw chiller technical manual (PLC series)
PE
L1 L2 L3
Appendix 4: circuit principle reference map
3P 50Hz M
JTX-A 380-400V 228A 3～
L N S1 S2 M1 M2
Z
X
Y
2
20
LSBLGW380/C WIRING DIAGRAM
L12 1X:22
Nb 1X:21
1X:43
1X:44
KM13
4/7B
4/7C
3/12C
3/12C
1ST1 1ST2
MCAC-CTSM-2013-01
99
T1 0.75mm,3A
L1 QF1 L1' L11 QF2 L21 FU1 QF4 L41 FU2 L51
1/12B 3/1B
1P 50Hz 1P 50Hz 6A 4A
1/12B N 230V 6A Na 230V 4A
N L
3/1B
～220V
L31 A10
24V
+V -V
57 N2
4/10B
FU3 59 84 86 88 90 4/10B
2A
QF3 KA4 KM11

1X:80
1X:79
1X:78
1X:77
A8 EVD
53 51 55
1X:25 1X:28
M EH1 EH2 76 78 80 82
1X:75 1X:76
NTC KA1
1X:26 1X:27
6/9F
6/10F
MCAC-CTSM-2013-01
100
SB
2/12B L51 L12 4/2F
1X:23
2/12B Na Nb SP4 4/2F
1X:24
61 1/3G
FR 1/3G
63
KA1
65
KM13 KM11 KM13 KM12

HMI
67 71 1X:31 2 4/8B
N L
24V 0V FG
～220V RS485 KT1 KM12 KT1 L
A9 SL1
24V 4/1D N
+V -V 73
4 4/3B 75 69
1X:32 24 4/8C
2 4/3B KM11 KM12 KM13 KT1
MCAC-CTSM-2013-01
101
2
3/6E 6/1E
3/6E 4 6/1F
1X:36 X:2 X:3 X:6 1X:371X:401X:411X:44 1X:481X:49 X:7 1X:521X:53
SQ1 SQ2 SP1 SP2 SQ3 KM12 SL1 SP3 FR FR1-6 KR1 SA1 SF1 SA
100
1X:35 X:1 X:4 X:5 1X:381X:391X:421X:43 KM11 1X:471X:50 X:8 1X:511X:54
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38
3/6E
A1 TM218LDAE40DRPHN 5/2E
92 94 96 98 1 3 5 7 9 11 13 15 17 19 21 23
X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 KA1 YV1 YV2 YV3 YV4 KM1 KM2 KM3 KM4 KM5 KM6
X:14 1X:2 1X:3 1X:6 1X:7 FR1 FR2 FR3 FR4 FR5 FR6
Nb Nb
3/12B 5/2C
L12 1X:29 1X:30 L13
3/12B 5/2C
SA
MCAC-CTSM-2013-01
102
6/5A
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 COM0COM0 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 COM1COM1
A3 TM2DRA16RT
KA6 KA7
X:22 X:21
43
X:19 X:20
41
YV5 YV6 YV7 YV8 YV9 KA4 KA2 KA5
X:18 X:17
39
X:15 X:16
37
1X:19 1X:20
35
1X:18 1X:17
33
1X:15 1X:16
31
1X:14 1X:13
29
1X:11 1X:12
27
1X:10 1X:9
25
A2
TM2DOCKN
L13
Nb
4/12D
4/12F
4/12F
103
5/12E
1X:55 1X:67
40 A A 64
1X:56 1X:68 RT5
RT1 B' B'
IN0
IN4
42 66
1X:57 1X:69
44 B B 68 P P
1X:58 TP1 TP2
46 A A + I_ + I_
1X:59
RT2 B' B'
IN1
IN5
48
1X:73
1X:72
1X:71
1X:70
1X:60
50 B A6 B 70 74
NC NC
1X:61
52 A A
1X:62
B' B'
IN2
IN6
54
TM2ARI8LT
1X:63
56 B B A7TM2AMM6HT
1X:64
58 A A
1X:65
RT4 B' B'
IN3
IN7
60
1X:66
62 B B
78 76
4/12B 2
+
4/12B 4
OV
2/8E
2/7E
MCAC-CTSM-2013-01
104
ITEM SYMBOL ITEM DESCRIPTION ITEM SYMBOL ITEM DESCRIPTION
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF

4QF 5QF
RT1~RT5
3 QF1 QF2 QF3 QF4 22 NTC
4 FU1 FU2 FU3 23 YV1~YV9
5 KR1 24 SP1 SP2 SP3
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR6 26 A1
8 M M A2
M 3~ 27
9 KT1 28 A3
10 KM1~KM6 29 A6
11 SB 30 A7
12 T1 31 HMI
13 EH1 EH2 32 A8
14 SQ1 33 A9
15 SQ2 34 A10
16 KA1 35
17 SA
18 SA1
19 SL1
MCAC-CTSM-2013-01
105
3P+N+PE 50Hz 380-400V
N 2/1B
N X1 X2 X2 X3 X3
L1 L1 L1 2/1B
L2 L2
L3 L3
PE 1QF 375A
3QF 16A
3*1.5mm+1*1.5mm
2QF 1A 11.6A
0.75mm,0.1A
KR1 L1 L2 L3 125
127
KM1 KM2 KM3 KM4 KM5 KM6 KM7 KM8
16 15 18 TA1 TA2
FR U11V11W11 U21V21W21 U31V31W31 U41V41W41 U51V51W51 U61V61W61 U71V71W71 U81V81W81
2 32 FR1 FR2 FR3 FR4 FR5 FR6 FR7 FR8
U1 V1 W1 PE U2 V2 W2 PE U3 V3 W3 PE U4 V4 W4 PE U5 V5 W5 PE U6 V6 W6 PE U7 V7 W7 PE U8 V8 W8 PE
123
4/9B 4/9C
KM11 KM12
3P 50Hz 380-400V 2.2kW 5.8A
3*95mm+1*50mm,191A
3*95mm
W
V
U
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 331A 3～
L N S1 S2 M1 M2
Z
X
Y
2
20
1X:43
1X:44
L12 1X:22
Nb 1X:21
KM13
4/7B
4/7C
3/12C
3/12C
1ST1 1ST2
MCAC-CTSM-2013-01
106
0.75mm,3A
QF1 L1' T1 L11 QF2 L21 FU1 QF4 L41 FU2 L51
1/12B L1 3/1B
1P 50Hz 1P 50Hz 6A 4A
1/12B N 230V 6A Na 230V 4A
N L
3/1B
～220V
A10
L31 24V
+V -V
57 N2
4/10B
FU3 59 84 86 88 90 4/10B
2A
QF3 KA4 KM11

1X:80
1X:79
1X:78
1X:77
A8 EVD
53 51 55
1X:25 1X:28
M EH1 EH2 76 78 80 82
1X:75 1X:76
NTC KA1
1X:26 1X:27
6/9F
6/10F
MCAC-CTSM-2013-01
107
SB
2/12B L51 L12 4/2F
1X:23
2/12B Na Nb
SP4 4/2F
1X:24
61 1/3G
FR 1/3G
63
KA1
65
KM13 KM11 KM13 KM12

HMI
67 71 1X:31 2 4/8B
N L
24V 0V FG
～220V RS485 KT1 KM12 KT1 L
A9 SL1
24V 4/1D N
+V -V 73
4 4/3B 75 69
1X:32 24 4/8C
2 4/3B KM11 KM12 KM13 KT1
MCAC-CTSM-2013-01
108
2
3/6E 6/1E
3/6E 4 6/1F
1X:36 X:2 X:3 X:6 1X:371X:401X:411X:44 1X:481X:49 X:7 1X:521X:53
100
1X:35 X:1 X:4 X:5 1X:381X:391X:421X:43 KM111X:471X:50 X:8 1X:511X:54
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38
3/6E
92 94 96 98 1 3 5 7 9 11 13 15 317 319 321 323

X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 KA1 YV1 YV2 YV3 YV4 KM1 KM2 KM3 KM4 KM5 KM6 KM7 KM8
X:14 1X:2 1X:3 1X:6 1X:7 FR1 FR2 FR3 FR4 FR5 FR6 FR7 FR8
Nb Nb
3/12B 5/2C
L12 1X:29 1X:30 L13
3/12B 5/2C
SA
MCAC-CTSM-2013-01
109
6/5A
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 COM0COM0 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15COM1COM1
KA6 KA7
X:22 X:21
43
X:19 X:20
41
X:18 X:17
39
A3 TM2DRA16RT
X:15 X:16
37
1X:19 1X:20
35
1X:18 1X:17
33
1X:15 1X:16
31
1X:14 1X:13
29
1X:11 1X:12
27
1X:10 1X:9
25
A2
TM2DOCKN
L13
Nb
4/12D
4/12F
4/12F
110
5/12E
1X:55 1X:67
40 A A 64
1X:56 RT5
RT1 B'
IN0
IN4
42 B' 66 1X:68
1X:57
B
A6 1X:69
44 B 68 P P
1X:58 TP1 TP2
46 A A + I_ + I_
1X:59
RT2 B' B'
IN1
IN5
48
1X:73
1X:72
1X:71
1X:70
1X:60
50 B B 70 74
TM2ARI8LT
NC NC
1X:61
52 A A
1X:62
B' B'
IN2
IN6
54
1X:63
56 B B A7TM2AMM6HT
1X:64
58 A A
1X:65
RT4 B' B'
IN3
IN7
60
1X:66
62 B B
2 78 76
4/12B +
4/12B 4
OV
2/8E
2/7E
MCAC-CTSM-2013-01
111
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF

4QF 5QF 6QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR8 26 A1
8 M M A2
M 3~
27
9 KT1 28 A3
10 KM1~KM8 29 A6
11 SB 30 A7
12 T1 31 HMI
13 EH1 EH2 32 A8
14 SQ1 33 A9
15 SQ2 34 A10
16 KA1 35
17 SA
18 SA1
19 SL1
MCAC-CTSM-2013-01
112
3P+N+PE 50Hz 380-400V
N B
N X1 X1 X2 X2 X3 X3 L1 2/1
L1 L1 2/1B
L2 L2
L3 L3
PE 1QF 385A
3QF 16A
3*1.5mm+1*1.5mm
2QF 1A 11.6A
0.75mm,0.1A
U01V01W01
KR1 L1 L2 L3 125
127
KM1 KM2 KM3 KM4 KM5 KM6 KM7 KM8 KM9 KM10
12 11 14 TA1 TA2
FR U11V11W11 U21V21W21 U31V31W31 U41V41W41 U51V51W51 U61V61W61 U71V71W71 U81V81W81 U91V91W91 U101V101W101
2 32 FR1 FR2 FR3 FR4 FR5 FR6 FR7 FR8 FR9 FR10
U1 V1 W1 PE U2 V2 W2 PE U3 V3 W3 PE U4 V4 W4 PE U5 V5 W5 PE U6 V6 W6 PE U7 V7 W7 PE U8 V8 W8 PE U9 V9 W9 PE U10V10W10 PE
123
4/9B 4/9C
KM11 KM12
3P 50Hz 380-400V 2.2kW 5.8A
3*95mm+1*50mm,191A
3*95mm
W
V
U
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 330A 3～
L N S1 S2 M1 M2
Z
X
Y
2
20
1X:43
1X:44
L12 1X:22
Nb 1X:21
KM13
4/7B
4/7C
3/12C
3/12C
1ST1 1ST2
MCAC-CTSM-2013-01
113
0.75mm,3A
1/12B L1 3/1B
1P 50Hz 1P 50Hz 6A 4A
1/12B N 230V 6A Na 230V 4A
N L
3/1B
～220V
A10
L31 24V
+V -V
57 N2
4/10B
FU3 59 84 86 88 90 4/10B
2A
QF3 KA4 KM11

1X:80
1X:79
1X:78
1X:77
A8 EVD
53 51 55
1X:25 1X:28
M EH1 EH2 76 78 80 82
1X:75 1X:76
NTC KA1
1X:26 1X:27
6/9F
6/10F
MCAC-CTSM-2013-01
114
SB
2/12B L51 L12 4/2F
1X:23
1X:24
61 1/3G
FR 1/3G
63
KA1
65
KM13 KM11 KM13 KM12

HMI
67 71 1X:31 2 4/8B
N L
24V 0V FG
～220V RS485 KT1 KM12 KT1 L
A9 SL1
24V 4/1D N
+V -V 73
4 4/3B 75 69
1X:32 24 4/8C
2 4/3B KM11 KM12 KM13 KT1
MCAC-CTSM-2013-01
115
2
3/6E 6/1E
3/6E 4 6/1F
1X:36 X:2 X:3 X:6 1X:371X:401X:411X:44 1X:481X:49 X:7 1X:521X:53
100
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38
3/6E
92 94 96 98 1 3 5 7 9 11 13 15 317 319 321 323

X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 KA1 YV1 YV2 YV3 YV4 KM1 KM2 KM3 KM4 KM5 KM6 KM7 KM8 KM9 KM10
X:14 1X:2 1X:3 1X:6 1X:7 FR1 FR2 FR3 FR4 FR5 FR6 FR7 FR8 FR9 FR10
Nb Nb
3/12B 5/2C
L12 1X:29 1X:30 L13
3/12B 5/2C
SA
MCAC-CTSM-2013-01
116
6/5A
KA6 KA7
X:22 X:21
43
X:19 X:20
41
X:18 X:17
39
A3 TM2DRA16RT
X:15 X:16
37
1X:19 1X:20
35
1X:18 1X:17
33
1X:15 1X:16
31
1X:14 1X:13
29
1X:11 1X:12
27
1X:10 1X:9
25
A2
TM2DOCKN
L13
Nb
4/12D
4/12F
4/12F
117
5/12E
1X:55 1X:67
40 A A 64
1X:56 RT5
RT1 B'
IN0
IN4
42 B' 66 1X:68
1X:57
B
A6 1X:69
44 B 68 P P
1X:58 TP1 TP2
46 A A + I_ + I_
1X:59
RT2 B' B'
IN1
IN5
48
1X:73
1X:72
1X:71
1X:70
1X:60
50 B B 70 74
TM2ARI8LT
NC NC
1X:61
52 A A
1X:62
B' B'
IN2
IN6
54
1X:63
56 B B A7TM2AMM6HT
1X:64
58 A A
1X:65
RT4 B' B'
IN3
IN7
60
1X:66
62 B B
2 78 76
4/12B +
4/12B 4
OV
2/8E
2/7E
MCAC-CTSM-2013-01
118
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF 4QF

5QF 6QF 6QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR10 26 A1
8 M M M 27 A2
3~
9 KT1 28 A3
10 KM1~KM10 29 A6
11 SB 30 A7
12 T1 31 HMI
13 EH1 EH2 32 A8
14 SQ1 33 A9
15 SQ2 34 A10
16 KA1 35
17 SA
18 SA1
19 SL1
MCAC-CTSM-2013-01
119
3P+N+PE 50Hz 380-400V
N 2/1B
N X1 X1 X2 X2 X3 X3
L1 L1 L1 2/1B
L2 L2
L3 L3
PE 1QF 545A
3QF 16A
3*1.5mm+1*1.5mm
2QF 1A 11.6A
0.75mm,0.1A
KR1 L1 L2 L3 125
127
KM1 KM2 KM3 KM4 KM5 KM6 KM7 KM8 KM9 KM10
12 11 14 TA1 TA2
FR U11V11W11 U21V21W21 U31V31W31 U41V41W41 U51V51W51 U61V61W61 U71V71W71 U81V81W81 U91V91W91 U101V101W101
2 32 FR1 FR2 FR3 FR4 FR5 FR6 FR7 FR8 FR9 FR10
U1 V1 W1 PE U2 V2 W2 PE U3 V3 W3 PE U4 V4 W4 PE U5 V5 W5 PE U6 V6 W6 PE U7 V7 W7 PE U8 V8 W8 PE U9 V9 W9 PE U10V10W10 PE
123
4/9B 4/9C
KM11 KM12
3P 50Hz 380-400V 2.2kW 5.8A
3*150mm+1*95mm,283A
3*150mm
W
V
U
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 490A 3～
L N S1 S2 M1 M2
Z
X
Y
2
20
1X:43
1X:44
L12 1X:22
Nb 1X:21
KM13
4/7B
4/7C
3/12C
3/12C
1ST1 1ST2
MCAC-CTSM-2013-01
120
0.75mm,3A
1/12B L1 3/1B
1P 50Hz 1P 50Hz 6A 4A
1/12B N 230V 6A Na 230V 4A
N L
3/1B
～220V
A10
L31 24V
+V -V
57 N2
4/10B
FU3 59 84 86 88 90 4/10B
2A
QF3 KA4 KM11

1X:80
1X:79
1X:78
1X:77
A8 EVD
53 51 55
1X:25 1X:28
M EH1 EH2 76 78 80 82
1X:75 1X:76
NTC KA1
1X:26 1X:27
6/9F
6/10F
MCAC-CTSM-2013-01
121
SB
2/12B L51 L12 4/2F
1X:23
1X:24
61 1/3G
FR 1/3G
63
KA1
65
KM13 KM11 KM13 KM12

HMI
67 71 1X:31 2 4/8B
N L
24V 0V FG
～220V RS485 KT1 KM12 KT1 L
A9 SL1
24V 4/1D N
+V -V 73
4 4/3B 75 69
1X:32 24 4/8C
2 4/3B KM11 KM12 KM13 KT1
MCAC-CTSM-2013-01
122
2
3/6E 6/1E
3/6E 4 6/1F
1X:36 X:2 X:3 X:6 1X:371X:401X:411X:44 1X:481X:49 X:7 1X:521X:53
100
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38
3/6E
92 94 96 98 1 3 5 7 9 11 13 15 317 319 321 323

X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 KA1 YV1 YV2 YV3 YV4 KM1 KM2 KM3 KM4 KM5 KM6 KM7 KM8 KM9 KM10
X:14 1X:2 1X:3 1X:6 1X:7 FR1 FR2 FR3 FR4 FR5 FR6 FR7 FR8 FR9 FR10
Nb Nb
3/12B 5/2C
L12 1X:29 1X:30 L13
3/12B 5/2C
SA
MCAC-CTSM-2013-01
123
6/5A
KA6 KA7
X:22 X:21
43
X:19 X:20
41
X:18 X:17
39
A3 TM2DRA16RT
X:15 X:16
37
1X:19 1X:20
35
1X:18 1X:17
33
1X:15 1X:16
31
1X:14 1X:13
29
1X:11 1X:12
27
1X:10 1X:9
25
A2
TM2DOCKN
L13
Nb
4/12D
4/12F
4/12F
124
5/12E
1X:55 1X:67
40 A A 64
1X:56 RT5
RT1 B'
IN0
IN4
42 B' 66 1X:68
1X:57
B
A6 1X:69
44 B 68 P P
1X:58 TP1 TP2
46 A A + I_ + I_
1X:59
RT2 B' B'
IN1
IN5
48
1X:73
1X:72
1X:71
1X:70
1X:60
50 B B 70 74
TM2ARI8LT
NC NC
1X:61
52 A A
1X:62
B' B'
IN2
IN6
54
1X:63
56 B B A7TM2AMM6HT
1X:64
58 A A
1X:65
RT4 B' B'
IN3
IN7
60
1X:66
62 B B
2 78 76
4/12B +
4/12B 4
OV
2/8E
2/7E
MCAC-CTSM-2013-01
125
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF 4QF

5QF 6QF 6QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR10 26 A1
8 M M 27 A2
M 3~
9 KT1 28 A3
10 KM1~KM10 29 A6
11 SB 30 A7
12 T1 31 HMI
13 EH1 EH2 32 A8
14 SQ1 33 A9
15 SQ2 34 A10
16 KA1 35
17 SA
18 SA1
19 SL1
MCAC-CTSM-2013-01
126
3P+N+PE 50Hz 380-400V
N X1 1X1 1X1 1X2
L1 1L1
L2 1L2
L3 1L3
PE 1.1QF 261A
1.3QF 16A
3*1.5mm+1*1.5mm
2QF 1A 11.6A
0.75mm,0.1A
L1 L2 L3 KR1 1.125
2/1B 1.127 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6
2/1B
2/1B 16 15 18 1TA1 1TA2
1.U11
1.U21
1.U31
1.U41
1.U51
1.U61
1.W11
1.W21
1.W31
1.W41
1.W51
1.W61
1.V11
1.V21
1.V31
1.V41
1.V51
1.V61
2/1B 2 1.32 1.FR

1FR1 1FR2 1FR3 1FR4 1FR5 1FR6
2/1B 1U1 1V1 1W1 PE 1U2 1V2 1W2 PE 1U3 1V3 1W3 PE 1U4 1V4 1W4 PE 1U5 1V5 1W5 PE 1U6 1V6 1W6 PE
3/1B 1.123
3/1B 5/9B 5/9C
1KM11 1KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*70mm+1*35mm,132A 3*70mm
W1
V1
U1
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 228A 3～
L N S1 S2 M1 M2
2
Z1
X1
Y1
Nb 1X:21
L12 1X:22
1.20 1X:43
1X:44
1KM13
5/7C
5/7B
4/12C
4/12C
1ST1 1ST2
MCAC-CTSM-2013-01
127
3P+N+PE 50Hz 380-400V
1/3D N 2X1 2X1 2X2 2X2
1/3D L1 2L1
L2 2L2
1/3D L3
1/3D PE 2L3
1/3D 2.1QF 375A
3*1.5mm+1*1.5mm
11.6A
2.125
2.127 2KM1 2KM2 2KM3 2KM4 2KM5 2KM6 2KM7 2KM8
2TA1 2TA2
2.U71
2.U81
2.U11
2.U21
2.U31
2.U41
2.U51
2.U61
2.W11
2.W21
2.W31
2.W41
2.W51
2.W61
2.V71
2.W71
2.V81
2.W81
2.FR
2.V11
2.V21
2.V31
2.V41
2.V51
2.V61
2FR1 2FR2 2FR3 2FR4 2FR5 2FR6 2FR5 2FR6

2U1 2V1 2W1 PE 2U2 2V2 2W2 PE 2U3 2V3 2W3 PE 2U4 2V4 2W4 PE 2U5 2V5 2W5 PE 2U6 2V6 2W6 PE 2U7 2V7 2W57 PE 2U8 2V8 2W8 PE
2.123
2KM11 2KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*95mm+1*50mm,191A 3*95mm
W2
V2
U2
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 331A 3～
L N S1 S2 M1 M2
2
Z2
X2
Y2
Nb 2X:21
L12 2X:22
2X:44
2.20 2X:43
2KM13
4/12D
4/12C
5/11C
5/11B
2ST1 2ST2
MCAC-CTSM-2013-01
128
T1 L11 QF2 L21 FU1 0.75mm,3A QF4 L41 FU2 L51 4/1B
L1 QF1 L1'
1/3D 1P 50Hz 1P 50Hz 6A 4A
N 230V 6A Na 230V 4A 4/1B
1/3D L31 N L
～ 220V
M M
3/9C
3/9C
A10
24V
+V -V 1X:77 1X:781X:791X:80 2X:77 2X:782X:792X:80
57 N2
FU3 59
3/5B
3/5B
7/8B
7/8B
1.84 2.86 2.88 2.90
5/10B
5/10B
2A 1.84 1.86 1.88 1.90
KA4 QF3 1KM11 2KM11

51 53 1.55 2.55 1A8 EVD 2A8 EVD
1X:25 1X:28 2X:28
EH1 M 1EH2 2EH2 1.76 1.78 1.80 1.82 2.76 2.78 2.80 2.82
1X:75
1X:76
2X:75
2X:76
1X:26 1X:27 2X:27 1NTC 1KA1 2NTC 2KA1

7/9G
7/8G
7/8G
7/7G
MCAC-CTSM-2013-01
129
SB1
L51 L12 L12
3/12B 5/2F
1X:23 2X:23
3/12B Na Nb Nb
1SP4 2SP4 5/2F
1X:24 2X:24 L12
1/2G
1.61 2.61
Nb
1FR 2FR 1/3G
L12
1.63 2.63 2/2G
Nb
2/3G
1KA1 2KA1 1X:31 2
1.65 2.65 5/8B
L
N
1.SL1
1KM13 1KM11 1KM13 1KM12 2KM13 2KM11 2KM13 2KM12
HMI
1.67 1.71 2.67 2.71 1X:32
N L 1.24 5/8C
24V 0V FG
～220V 1KT1 1KM12 1KT1 2KT1 2KM12 2KT1
A9 RS485
24V 5/1D 2X:31 2
+V -V 1.73 2.73
4 1.75 1.69 2.75 2.69 7/7B
5/3B L
2 5/3B 1KM11 1KM12 1KM13 1KT1 2KM11 2KM12 2KM13 2KT1 2.SL1
N
2X:32 2.24 7/7C

MCAC-CTSM-2013-01
130
2
4/4E 7/1H
4/4E 4 7/1H
1X:36 X:2 X:3 X:6 1X:37 1X:40 1X:41 1X:44 1X:48 1X:49 X:7 1X:52 1X:53 2X:40 2X:41 2X:44
SQ1 SQ2 1.SP1 1.SP21.SQ3 1KM12 1.SL1 1.SP3 1.FR 1.FR1-6 KR1 SA1 1.K5 SA 2.SP1 2.SP2 2.SQ3
1.100
1X:35 X:1 X:4 X:5 1X:38 1X:39 1X:42 1X:43 1KM111X:47 1X:50 X:8 1X:51 1X:54 2X:39 2X:42 2X:43
1.6 1.8 1.10 1.12 1.14 1.16 1.18 1.20 1.22 1.24 1.26 1.28 1.30 1.32 1.34 1.36 1.38 2.16 2.18 2.20
A1 TM218LDAE40DRPHN 6/3D
4/4E
92 94 96 98 1.1 1.3 1.5 1.7 1.9 1.11 1.13 1.15 1.17 1.191.21 1.23
X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 1KA1 1YV1 1YV2 1YV3 1YV4 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6
1FR1 1FR2 1FR3 1FR4 1FR5 1FR6

X:14 1X:2 1X:3 1X:6 1X:7
4/12B Nb
6/1E
L12 L12 1X:29 1X:30 L13
4/12B 6/1F
SA
MCAC-CTSM-2013-01
131
2X:10
2X:14
2X:15
2X:18
X:23
2X:11
2FR2 2FR3 2FR4 2FR5 2FR6 2FR7 2FR8
2YV5 2YV6 2YV7 2YV8 2YV9 2KA2
A2 2KM2 2KM3 2KM42KM5 2KM62KM7 2KM8
2X:9
2X:13
2X:12
2X:16
2X:17
X:24
2.15 2.172.192.21 2.23 2.25 2.27 2.29 2.31 2.33 2.37
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 COM0COM0Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15COM1COM1
A4 TM2DRA16RT
TM2DOCKN
5/12D
A3 TM2DRA16RT 7/5C
1.25 1.27 1.29 1.31 1.33 1.35 1.37 1.39 1.41 1.43 2.3 2.5 2.7 2.9 2.11 2.13
1X:20
X:20
1X:13
1X:12
1X:16
1X:17
1X:9
X:16
X:17
2X:4
2X:5
2X:8
X:21
2X:1
2KM1
1YV5 1YV6 1YV7 1YV8 1YV9 KA4 1KA2 KA5 KA6 KA7 2KA1 2YV1 2YV2 2YV3 2YV4 2FR1
Nb
1X:10
2X:3
1X:14
1X:19
1X:15
1X:18
X:15
X:18
X:19
X:22
2X:2
2X:6
2X:7
1X:11
5/12F
5/12F L13
MCAC-CTSM-2013-01
132
1X:55 1X:67 2X:482X:49 2X:52 2X:53
1.40 A A 2.64
1X:56 2KM12 2.SL1 2.SP3 2.FR 2.K5
B'
IN0
IN4
1.42 B' 2.66 1X:68
1.RT1
1.RT5
2.100 2.FR1-8
1X:57 A6 1X:69
1.44 B B 2.68 2KM11 2X:472X:50 2X:51 2X:51
1X:58 2X:61 2.22 2.24 2.26 2.28 2.30 2.36 2.38
1.46 A A 2.52
1X:59 2X:62 I0 I1 I2 I3 I4 I5 I6 I7 COM COM I8 I9 I10 I11 I12 I13 I14 I15 COM COM
B' B' 6/11D
IN1
IN5
1.48 2.54
1.RT2
1X:60 2X:63 A5 TM2DDI16DT
1.50 B B 2.56
TM2ARI8LT
NC NC
1X:61 2X:67 1.TP1 1.TP2 2.TP1 2.TP2
1.52 A A 2.64 P P P P
1X:62 2X:68
B' + I_ + I_ + I_ + I_
IN2
IN6
1.54 B' 2.66
2.RT5
1X:63 2X:69
1.56 B
1X:73
2X:73
1X:72
2X:72
1X:71
B 2.68
1X:70
2X:71
2X:70
2 7/1H
1X:64 1.70 1.74 2.70 2.74 4
1.58 A A 7/1H
1X:65
B' B'
IN3
IN7
1.60
1.RT4
1X:66
1.62 B B
+ A7TM2AMM6HT
OV
1.78 1.76 2.78 2.76

3/5E 3/5E 3/9E 3/9E
4 2
5/12B 5/12B
MCAC-CTSM-2013-01
133
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF

4QF 5QF 6QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR8 26 A1
8 M M 27 A2
M 3~
9 KT1 28 A3 A4
10 KM1~KM8 29 A5
11 SB 30 A6
12 T1 31 A7
13 EH1 EH2 32 HMI
14 SQ1 33 A8
15 SQ2 34 A9
16 KA1 35 A10
17 SA 36
18 SA1
19 SL1
MCAC-CTSM-2013-01
134
3P+N+PE 50Hz 380-400V
N X1 1X1 1X1 1X2 1X2
L1 1L1
L2 1L2
L3 1L3
PE 1.1QF 375A
1.3QF 16A
3*1.5mm+1*1.5mm
2QF 1A 11.6A
0.75mm,0.1A
L1 L2 L3 KR1 1.125
2/1B 1.127 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6 1KM7 1KM8
2/1B
2/1B 16 15 18 1TA1 1TA2
1.U11
1.U21
1.U31
1.U41
1.U51
1.U61
1.U71
1.U81
1.W11
1.W21
1.W31
1.W41
1.W51
1.W61
1.W71
1.W81
1.V11
1.V21
1.V31
1.V41
1.V51
1.V61
1.V71
1.V81
2/1B 2 1.32 1.FR

2/1B 1U1 1V1 1W1 PE 1U2 1V2 1W2 PE 1U3 1V3 1W3 PE 1U4 1V4 1W4 PE 1U5 1V5 1W5 PE 1U6 1V6 1W6 PE 1U7 1V7 1W7 PE 1U8 1V8 1W8 PE
3/1B 1.123
3/1B 5/9B 5/9C
1KM11 1KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*95mm+1*50mm,191A 3*95mm
W1
V1
U1
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 331A 3～
L N S1 S2 M1 M2
2
Z1
X1
Y1
Nb 1X:21
L12 1X:22
1.20 1X:43
1X:44
1KM13
5/7C
5/7B
4/12C
4/12C
1ST1 1ST2
MCAC-CTSM-2013-01
135
3P+N+PE 50Hz 380-400V
1/3D N 2X1 2X1 2X2 2X2
1/3D L1 2L1
2L2
1/3D L2 2L3
1/3D L3
1/3D PE 2.1QF 375A
3*1.5mm+1*1.5mm
11.6A
2.125
2TA1 2TA2
2.U11
2.U21
2.U31
2.U41
2.U51
2.U61
2.U71
2.U81
2.FR
2.W11
2.W21
2.W31
2.W41
2.W51
2.W61
2.W71
2.W81
2.V11
2.V21
2.V31
2.V41
2.V51
2.V61
2.V71
2.V81

2.123
2KM11 2KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*95mm+1*50mm,191A 3*95mm
W2
V2
U2
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 331A 3～
L N S1 S2 M1 M2
2
Z2
X2
Y2
Nb 2X:21
L12 2X:22
2X:44
2.20 2X:43
2KM13
4/12D
4/12C
5/11C
5/11B
2ST1 2ST2
MCAC-CTSM-2013-01
136
L1 QF1 L1'
1/3D 1P 50Hz 1P 50Hz 6A 4A
N 230V 6A Na 230V 4A 4/1B
1/3D L31 N L
～ 220V
M M
3/9C
3/9C
A10
24V
+V -V 1X:77 1X:781X:791X:80 2X:772X:782X:792X:80
57 N2
FU3 59
3/5B
3/5B
5/10B
5/10B
1.84 1.86 1.88 1.90 1.84 2.86 2.88 2.90
7/8B
7/8B
2A
KA4 QF3 1KM11 2KM11

51 53 1.55 2.55 1A8 EVD 2A8 EVD
1X:25 1X:28 2X:28
EH1 M 1EH2 2EH2 1.76 1.78 1.80 1.82 2.76 2.78 2.80 2.82
1X:75
1X:76
2X:75
2X:76
1X:26 1X:27 2X:27 1NTC 1KA1 2NTC 2KA1

7/8G
7/7G
7/9G
7/8G
MCAC-CTSM-2013-01
137
SB1
L51 L12 L12
3/12B 5/2F
1X:23 2X:23
3/12B Na Nb Nb
1SP4 2SP4 5/2F
1X:24 2X:24 L12
1/2G
1.61 2.61
Nb
1FR 2FR 1/3G
L12
1.63 2.63 2/2G
Nb
2/3G
1KA1 2KA1 1X:31 2
1.65 2.65 5/8B
L
N
1.SL1
HMI
1.67 1.71 2.67 2.71 1X:32
N L 1.24 5/8C
24V 0V FG
～220V 1KT1 1KM12 1KT1 2KT1 2KM12 2KT1
A9 RS485
24V 5/1D 2X:31 2
+V -V 1.73 2.73
4 1.75 1.69 2.75 2.69 7/7B
5/3B L
N
2X:32 2.24 7/7C

MCAC-CTSM-2013-01
138
2
4/4E 7/1H
4/4E 4 7/1H
SQ1 SQ2 1.SP1 1.SP2 1.SQ3 1KM12 1.SL1 1.SP3 1.FR 1.FR1-8 KR1 SA1 1.K5 SA 2.SP1 2.SP2 2.SQ3
1.100
1.6 1.8 1.10 1.12 1.14 1.16 1.18 1.20 1.22 1.24 1.26 1.28 1.301.32 1.34 1.36 1.38 2.16 2.18 2.20
4/4E
92 94 96 98 1.1 1.3 1.5 1.7 1.9 1.11 1.13 1.15 1.17 1.191.21 1.23
X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 1KA1 1YV1 1YV2 1YV3 1YV4 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6 1KM7 1KM8

X:14 1X:2 1X:3 1X:6 1X:7
4/12B Nb
6/1E
L12 L12 1X:29 1X:30 L13
4/12B 6/1F
SA
MCAC-CTSM-2013-01
139
2X:10
X:23
2X:14
2X:15
2X:18
2X:11
2FR2 2FR3 2FR4 2FR5 2FR62FR7 2FR8
2X:9
2X:13
2X:12
2X:16
2X:17
X:24
2.15 2.172.192.21 2.23 2.25 2.27 2.29 2.31 2.33 2.37
A4 TM2DRA16RT
TM2DOCKN
5/12D
A3 TM2DRA16RT 7/5C
1.25 1.27 1.29 1.31 1.33 1.35 1.37 1.39 1.41 1.43 2.3 2.5 2.7 2.9 2.11 2.13
1X:20
1X:13
X:20
1X:12
1X:16
1X:17
1X:9
X:16
X:17
2X:4
2X:5
2X:8
X:21
2X:1
2KM1
Nb
1X:10
2X:3
1X:14
1X:19
1X:15
1X:18
X:15
X:18
X:19
X:22
2X:2
2X:6
2X:7
1X:11
5/12F
5/12F L13
MCAC-CTSM-2013-01
140
1X:55 1X:67 2X:482X:49 2X:52 2X:53
1.40 A A 2.64
1X:56 1X:68 2KM12 2.SL1 2.SP3 2.FR 2.K5
B' B'
IN0
IN4
1.42 2.66
1.RT1
1.RT5
2.100 2.FR1-8
1X:57 A6 1X:69
1.44 B B 2.68 2KM11 2X:472X:50 2X:51 2X:51
1X:58 2X:61 2.22 2.24 2.26 2.28 2.30 2.36 2.38
1.46 A A 2.52
B' B' 6/11D
IN1
IN5
1.48 2.54
1.RT2
1.50 B B 2.56
TM2ARI8LT
NC NC
1X:61 2X:67 1.TP1 1.TP2 2.TP1 2.TP2
1.52 A A 2.64 P P P P
1X:62 2X:68
B' B' + I_ + I_ + I_ + I_
IN2
IN6
1.54 2.66
2.RT5
1X:63 2X:69
B B
1X:73
2X:73
1.56
1X:72
2X:72
1X:71
1X:70
2X:71
2.68
2X:70
2 7/1H
1X:64 1.70 1.74 2.70 2.74 4
1.58 A A 7/1H
1X:65
B' B'
IN3
IN7
1.60
1.RT4
1X:66
1.62 B B
+ A7TM2AMM6HT
OV
1.78 1.76 2.78 2.76

3/5E 3/5E 3/9E 3/9E
4 2
5/12B 5/12B
MCAC-CTSM-2013-01
141
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF

4QF 5QF 6QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR8 26 A1
8 M M 27 A2
M 3~
9 KT1 28 A3 A4
10 KM1~KM8 29 A5
11 SB 30 A6
12 T1 31 A7
13 EH1 EH2 32 HMI
14 SQ1 33 A8
15 SQ2 34 A9
16 KA1 35 A10
17 SA 36
18 SA1
19 SL1
MCAC-CTSM-2013-01
142
3P+N+PE 50Hz 380-400V
N X1 1X1 1X1 1X2 1X2
L1 1L1
L2 1L2
L3 1L3
PE 1.1QF 374A
1.3QF 16A
3*1.5mm+1*1.5mm
2QF 1A 11.6A
0.75mm,0.1A
L1 L2 L3 KR1 1.125
2/1B 1.127 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6 1KM7 1KM8
2/1B
2/1B 16 15 18 1TA1 1TA2
1.U11
1.U21
1.U31
1.U41
1.U51
1.U61
1.U71
1.U81
1.V11
1.W11
1.V21
1.W21
1.V31
1.W31
1.V41
1.W41
1.V51
1.W51
1.V61
1.W61
1.V71
1.W71
1.V81
1.W81
2/1B 2 1.32 1.FR

2/1B 1U1 1V1 1W1 PE 1U2 1V2 1W2 PE 1U3 1V3 1W3 PE 1U4 1V4 1W4 PE 1U5 1V5 1W5 PE 1U6 1V6 1W6 PE 1U7 1V7 1W7 PE 1U8 1V8 1W8 PE
3/1B 1.123
3/1B 5/9B 5/9C
1KM11 1KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*95mm+1*50mm,191A 3*95mm
W1
V1
U1
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 330A 3～
L N S1 S2 M1 M2
2
Z1
X1
Y1
Nb 1X:21
L12 1X:22
1.20 1X:43
1X:44
1KM13
5/7C
5/7B
4/12C
4/12C
1ST1 1ST2
MCAC-CTSM-2013-01
143
3P+N+PE 50Hz 380-400V
1/3D N 2X1 2X1 2X2 2X2
1/3D L1 2L1
2L2
1/3D L2 2L3
1/3D L3
1/3D PE 2.1QF 374A
3*1.5mm+1*1.5mm
11.6A
2.125
2TA1 2TA2
2.U11
2.U21
2.U31
2.U41
2.U51
2.U61
2.U71
2.U81
2.W11
2.W21
2.W31
2.W41
2.W51
2.W61
2.W71
2.W81
2.V11
2.V21
2.V31
2.V41
2.V51
2.V61
2.V71
2.V81
2.FR
2.123
2KM11 2KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*95mm+1*50mm,191A 3*95mm
W2
V2
U2
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 330A 3～
L N S1 S2 M1 M2
2
Z2
X2
Y2
Nb 2X:21
L12 2X:22
2.20 2X:43
2X:44
2KM13
4/12D
4/12C
5/11C
5/11B
2ST1 2ST2
MCAC-CTSM-2013-01
144
L1 QF1 L1'
1/3D 1P 50Hz 1P 50Hz 6A 4A
N 230V 6A Na 230V 4A 4/1B
1/3D L31 N L
～ 220V
M M
3/9C
3/9C
A10
24V
+V -V 1X:77 1X:781X:791X:80 2X:772X:782X:792X:80
57 N2
FU3 59
3/5B
3/5B
5/10B
5/10B
1.84 1.86 1.88 1.90 1.84 2.86 2.88 2.90
7/8B
7/8B
2A
KA4 QF3 1KM11 2KM11

51 53 1.55 2.55 1A8 EVD 2A8 EVD
1X:25 1X:28 2X:28
EH1 M 1EH2 2EH2 1.76 1.78 1.80 1.82 2.76 2.78 2.80 2.82
1X:75
1X:76
2X:75
2X:76
1X:26 1X:27 2X:27 1NTC 1KA1 2NTC 2KA1

7/8G
7/7G
7/9G
7/8G
MCAC-CTSM-2013-01
145
SB1
L51 L12 L12
3/12B 5/2F
1X:23 2X:23
3/12B Na Nb Nb
1SP4 2SP4 5/2F
1X:24 2X:24 L12
1/2G
1.61 2.61
Nb
1FR 2FR 1/3G
L12
1.63 2.63 2/2G
Nb
2/3G
1KA1 2KA1 1X:31 2
1.65 2.65 5/8B
L
N
1.SL1
HMI
1.67 1.71 2.67 2.71 1X:32
N L 1.24 5/8C
24V 0V FG
～220V 1KT1 1KM12 1KT1 2KT1 2KM12 2KT1
A9 RS485
24V 5/1D 2X:31 2
+V -V 1.73 2.73
4 1.75 1.69 2.75 2.69 7/7B
5/3B L
N
2X:32 2.24 7/7C

MCAC-CTSM-2013-01
146
2
4/4E 7/1H
4/4E 4 7/1H
1.100
1.6 1.8 1.10 1.12 1.14 1.16 1.18 1.20 1.22 1.24 1.26 1.28 1.301.32 1.34 1.36 1.38 2.16 2.18 2.20
4/4E
92 94 96 98 1.1 1.3 1.5 1.7 1.9 1.11 1.13 1.15 1.17 1.191.21 1.23
X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 1KA1 1YV1 1YV2 1YV3 1YV4 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6 1KM7 1KM8

X:14 1X:2 1X:3 1X:6 1X:7
4/12B Nb
6/1E
L12 L12 1X:29 1X:30 L13
4/12B 6/1F
SA
MCAC-CTSM-2013-01
147
2X:10
X:23
2X:14
2X:15
2X:18
2X:11
2FR2 2FR3 2FR4 2FR5 2FR62FR7 2FR8
2X:9
2X:13
2X:12
2X:16
2X:17
X:24
2.15 2.172.192.21 2.23 2.25 2.27 2.29 2.31 2.33 2.37
A4 TM2DRA16RT
TM2DOCKN
5/12D
A3 TM2DRA16RT 7/5C
1.25 1.27 1.29 1.31 1.33 1.35 1.37 1.39 1.41 1.43 2.3 2.5 2.7 2.9 2.11 2.13
1X:20
1X:13
X:20
1X:12
1X:16
1X:17
1X:9
X:16
X:17
2X:4
2X:5
2X:8
X:21
2X:1
2KM1
Nb
1X:10
2X:3
1X:14
1X:19
1X:15
1X:18
X:15
X:18
X:19
X:22
2X:2
2X:6
2X:7
1X:11
5/12F
5/12F L13
MCAC-CTSM-2013-01
148
1X:55 1X:67 2X:482X:49 2X:52 2X:53
1.40 A A 2.64
1X:56 1X:68 2KM12 2.SL1 2.SP3 2.FR 2.K5
B' B'
IN0
IN4
1.42 2.66
1.RT1
1.RT5
2.100 2.FR1-8
1X:57 A6 1X:69
1.44 B B 2.68 2KM11 2X:472X:50 2X:51 2X:51
1X:58 2X:61 2.22 2.24 2.26 2.28 2.30 2.36 2.38
1.46 A A 2.52
B' B' 6/11D
IN1
IN5
1.48 2.54
1.RT2
1.50 B B 2.56
TM2ARI8LT
NC NC
1X:61 2X:67 1.TP1 1.TP2 2.TP1 2.TP2
1.52 A A 2.64 P P P P
1X:62 2X:68
B' B' + I_ + I_ + I_ + I_
IN2
IN6
1.54 2.66
2.RT5
1X:63 2X:69
B B
1X:73
2X:73
1.56
1X:72
2X:72
1X:71
1X:70
2X:71
2.68
2X:70
2 7/1H
1X:64 1.70 1.74 2.70 2.74 4
1.58 A A 7/1H
1X:65
B' B'
IN3
IN7
1.60
1.RT4
1X:66
1.62 B B
+ A7TM2AMM6HT
OV
1.78 1.76 2.78 2.76

3/5E 3/5E 3/9E 3/9E
4 2
5/12B 5/12B
MCAC-CTSM-2013-01
149
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF

4QF 5QF 6QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR8 26 A1
8 M M 27 A2
M 3~
9 KT1 28 A3 A4
10 KM1~KM8 29 A5
11 SB 30 A6
12 T1 31 A7
13 EH1 EH2 32 HMI
14 SQ1 33 A8
15 SQ2 34 A9
16 KA1 35 A10
17 SA 36
18 SA1
19 SL1
MCAC-CTSM-2013-01
150
3P+N+PE 50Hz 380-400V
N X1 1X1 1X1 1X2 1X2 1X3
L1 1L1
L2 1L2
L3 1L3
PE 1.1QF 545A
1.3QF 16A
3*1.5mm
2QF 1A +1*1.5mm
11.6A
0.75mm,0.1A
L1 L2 L3 KR1 1.125
2/1B 1.127 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6 1KM7 1KM8 1KM9 1KM10
2/1B
2/1B 16 15 18 1TA1 1TA2
1.U11
1.U21
1.U31
1.U41
1.U51
1.U61
1.U71
1.U81
1.U91
1.U101
1.W11
1.W21
1.W31
1.W41
1.W51
1.W61
1.W71
1.W81
1.W91
1.V11
1.V21
1.V31
1.V41
1.V51
1.V61
1.V71
1.V81
1.V91
1.W101
1.V101
2/1B 2 1.32 1.FR

1FR1 1FR2 1FR3 1FR4 1FR5 1FR6 1FR7 1FR8 1FR10
2/1B 1U1 1V1 1W1 PE 1U2 1V2 1W2 PE 1U3 1V3 1W3 PE 1U4 1V4 1W4 PE 1U5 1V5 1W5 PE 1U6 1V6 1W6 PE 1U7 1V7 1W7 PE 1U8 1V8 1W8 PE 1U9 1V9 1W9 PE 1U101V10 1W10 PE
3/1B 1.123
3/1B 5/9B 5/9C
1KM11 1KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*150mm+1*95mm,283A 3*150mm
W1
V1
U1
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 490A 3～
L N S1 S2 M1 M2
2
Z1
X1
Y1
Nb 1X:21
L12 1X:22
1X:44
1.20 1X:43
1KM13
5/7C
5/7B
4/12C
4/12C
1ST1 1ST2
MCAC-CTSM-2013-01
151
3P+N+PE 50Hz 380-400V
1/3D N 2X1 2X1 2X2 2X2 2X3
1/3D L1 2L1
2L2
1/3D L2 2L3
1/3D L3
1/3D PE 2.1QF 545A
3*1.5mm+1*1.5mm
11.6A
2.125
2.127 2KM1 2KM2 2KM3 2KM4 2KM5 2KM6 2KM7 2KM8 2KM9 2KM10
2TA1 2TA2
2.U11
2.U21
2.U31
2.U41
2.U51
2.U61
2.U71
2.U81
2.U91
2.U101
2.W11
2.W21
2.W31
2.W41
2.W51
2.W61
2.W71
2.W81
2.W91
2.V11
2.V21
2.V31
2.V41
2.V51
2.V61
2.V71
2.V81
2.V91
2.W101
2.FR
2.V101
2FR1 2FR2 2FR3 2FR4 2FR5 2FR6 2FR7 2FR8 2FR9 2FR10
2U1 2V1 2W1 PE 2U2 2V2 2W2 PE 2U3 2V3 2W3 PE 2U4 2V4 2W4 PE 2U5 2V5 2W5 PE 2U6 2V6 2W6 PE 2U7 2V7 2W7 PE 2U8 2V8 2W8 PE 2U9 2V9 2W9 PE 2U10 2V10 2W10 PE
2.123
2KM11 2KM12 3P 50Hz 380-400V 2.2kW 5.8A

3*150mm+1*95mm,283A 3*150mm
W2
V2
U2
PE
L1 L2 L3
3P 50Hz M
JTX-A 380-400V 490A 3～
L N S1 S2 M1 M2
2
Z2
X2
Y2
L12 2X:22
Nb 2X:21
2X:44
2.20 2X:43
2KM13
4/12D
4/12C
5/11C
5/11B
2ST1 2ST2
MCAC-CTSM-2013-01
152
L1 QF1 L1'
1/3D 1P 50Hz 1P 50Hz 6A 4A
N 230V 6A Na 230V 4A 4/1B
1/3D L31 N L
～ 220V
M M
3/9C
3/9C
A10
24V
+V -V 1X:77 1X:781X:791X:80 2X:772X:782X:792X:80
57 N2
FU3 59
3/5B
3/5B
5/10B
5/10B
1.84 1.86 1.88 1.90 1.84 2.86 2.88 2.90
7/8B
7/8B
2A
KA4 QF3 1KM11 2KM11

51 53 1.55 2.55 1A8 EVD 2A8 EVD
1X:25 1X:28 2X:28
EH1 M 1EH2 2EH2 1.76 1.78 1.80 1.82 2.76 2.78 2.80 2.82
1X:75
1X:76
2X:75
2X:76
1X:26 1X:27 2X:27 1NTC 1KA1 2NTC 2KA1

7/8G
7/7G
7/9G
7/8G
MCAC-CTSM-2013-01
153
SB1
L51 L12 L12
3/12B 5/2F
1X:23 2X:23
3/12B Na Nb Nb
1SP4 2SP4 5/2F
1X:24 2X:24 L12
1/2G
1.61 2.61
Nb
1FR 2FR 1/3G
L12
1.63 2.63 2/2G
Nb
2/3G
1KA1 2KA1 1X:31 2
1.65 2.65 5/8B
L
N
1.SL1
HMI
1.67 1.71 2.67 2.71 1X:32
N L 1.24 5/8C
24V 0V FG
～220V 1KT1 1KM12 1KT1 2KT1 2KM12 2KT1
A9 RS485
24V 5/1D 2X:31 2
+V -V 1.73 2.73
4 1.75 1.69 2.75 2.69 7/7B
5/3B L
N
2X:32 2.24 7/7C

MCAC-CTSM-2013-01
154
2
4/4E 7/1H
4/4E 4 7/1H
1.100
1X:35 X:1 X:4 X:5 1X:38 1X:39 1X:42 1X:43 1KM11 1X:47 1X:50 X:8 1X:51 1X:54 2X:39 2X:42 2X:43
1.6 1.8 1.10 1.12 1.14 1.16 1.18 1.20 1.22 1.24 1.26 1.28 1.30 1.32 1.34 1.36 1.38 2.16 2.18 2.20
4/4E
92 94 96 98 1.1 1.3 1.5 1.7 1.9 1.11 1.13 1.15 1.17 1.191.21 1.23
X:9 X:10 X:11 X:12 X:13 1X:1 1X:4 1X:5 1X:8
KA3 1KA1 1YV1 1YV2 1YV3 1YV4 1KM1 1KM2 1KM3 1KM4 1KM5 1KM6 1KM71KM81KM91KM10
1FR1 1FR2 1FR3 1FR4 1FR5 1FR6 1FR71FR81FR91FR10

X:14 1X:2 1X:3 1X:6 1X:7

4/12B Nb 6/1E
L12 L12 1X:29 1X:30 L13 6/1F
4/12B
SA
MCAC-CTSM-2013-01
155
2X:10
X:23
2X:14
2X:15
2X:18
2X:11
2FR2 2FR3 2FR4 2FR5 2FR62FR7 2FR82FR92FR10
A2 2KM2 2KM3 2KM42KM5 2KM62KM7 2KM82KM92KM10
2X:9
2X:13
X:24
2X:12
2X:16
2X:17
2.15 2.172.192.21 2.23 2.25 2.27 2.29 2.31 2.33 2.37
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7COM0COM0Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15COM1COM1
A4 TM2DRA16RT
TM2DOCKN
5/12D
A3 TM2DRA16RT 7/5C
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 COM0COM0 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 COM1 COM1
1.25 1.27 1.29 1.31 1.33 1.35 1.37 1.39 1.41 1.43 2.3 2.5 2.7 2.9 2.11 2.13
1X:20
X:20
1X:13
1X:9
1X:12
1X:16
1X:17
X:16
X:17
2X:4
2X:5
2X:8
X:21
2X:1
2KM1
Nb
1X:10
2X:3
1X:14
1X:15
1X:18
1X:19
X:15
X:18
X:19
X:22
2X:2
2X:6
2X:7
1X:11
5/12F
5/12F L13
MCAC-CTSM-2013-01
156
1X:55 1X:67 2X:482X:49 2X:52 2X:53
1.40 A A 2.64
1X:56 2KM12 2.SL1 2.SP3 2.FR 2.K5
B'
IN0
IN4
1.42 B' 2.66 1X:68
1.RT1
1.RT5
2.100 2.FR1-10
1X:57 A6 1X:69
1.44 B B 2.68 2KM11 2X:472X:50 2X:51 2X:51
1X:58 2X:61 2.22 2.24 2.26 2.28 2.30 2.36 2.38
1.46 A A 2.52
B' B' 6/11D
IN1
IN5
1.48 2.54
1.RT2
1.50 B B 2.56
TM2ARI8LT
NC NC
1X:61 2X:67 1.TP1 1.TP2 2.TP1 2.TP2
1.52 A A 2.64 P P P P
1X:62 2X:68
B' + I_ + I_ + I_ + I_
IN2
IN6
1.54 B' 2.66
2.RT5
1X:63 2X:69
B
1X:73
1.56
1X:72
2X:73
2X:72
1X:71
B 2.68
1X:70
2X:71
2X:70
2 7/1H
1X:64 1.70 1.74 2.70 2.74 4
1.58 A A 7/1H
1X:65
B' B'
IN3
IN7
1.60
1.RT4
1X:66
1.62 B B
+ A7TM2AMM6HT
OV
1.78 1.76 2.78 2.76

3/5E 3/5E 3/9E 3/9E
4 2
5/12B 5/12B
MCAC-CTSM-2013-01
157
1 TA1 TA2 20 SQ3
2 1QF 21 2QF 3QF

4QF 5QF 6QF 7QF
RT1~RT5
6 KM11 KM12 KM13 25 TP1 TP2 P

I
7 FR FR1~FR10 26 A1
8 M M 27 A2
M 3~
9 KT1 28 A3 A4
10 KM1~KM10 29 A5
11 SB 30 A6
12 T1 31 A7
13 EH1 EH2 32 HMI
14 SQ1 33 A8
15 SQ2 34 A9
16 KA1 35 A10
17 SA 36
18 SA1
19 SL1
MCAC-CTSM-2013-01
158
140

Chiller Midea PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Chiller Midea PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chiller Midea PDF

Uploaded by

Copyright:

Available Formats

Air-cooled screw chiller technical manual (PLC series) MCAC-CTSM-2013-01

Air cooled screw chiller

All empires fall, you just have to know where to push. 1

C: R134a; omit for R22

380: nominal cooling capability (kW)

LG: Screw compressor

LS: water chiller

LSBLGW380/C 380V/3Ph/50Hz 376 1 6

LSBLGW500/C 380V/3Ph/50Hz 496 1 8

LSBLGW600/C 380V/3Ph/50Hz 594 1 10

LSBLGW720/C 380V/3Ph/50Hz 720 1 10

LSBLGW880/C 380V/3Ph/50Hz 880 2 14

LSBLGW1000/C 380V/3Ph/50Hz 996 2 16

LSBLGW1200/C 380V/3Ph/50Hz 1203 2 16

LSBLGW1420/C 380V/3Ph/50Hz 1419 2 20

LSBLGW380/C module LSBLGW500/C module

LSBLGW600/C LSBLGW720/C module LSBLGW880/C module

LSBLGW1000/C LSBLGW1200/C module

Economical Operation Cost

Lower operating noise

Simple Structure, Easy Installation

State of Technique, Accuracy Control

Modular design, Flexible combination

Unit Model LSBLGCW380/C LSBLGCW500/C LSBLGW600/C LSBLGW720/C

1) Nominal cooling capacities are based on the following conditions:

Chilled water inlet/outlet temp: 12℃/7℃; Outdoor temp (DB/WB):35℃/24℃.

Unit Model LSBLGCW880/C LSBLGCW1000/C LSBLGW1200/C LSBLGW1420/C

Air Side Fans Quantity 14 16 16 20

Chilled water inlet/outlet temp: 12℃/7℃; Outdoor temp (DB/WB):35℃/24℃.

Content Running range

Leaving water Temp. 5℃～15℃

(2) LSBLGW500/C unit (mm)

(3) LSBLGW600/C unit (mm)

(4) LSBLGW720/C unit (mm)

(5) LSBLGW880/C unit (mm)

(6) LSBLGW1000/C unit (mm)

(7) LSBLGW1200/C unit (mm)

(7) LSBLGW1420/C unit (mm)

8. Water Flow – Water Drop Pressure Curve

Unit Model MIN. FLOW RATE MAX. FLOW RATE

1. Installation Dimensions & Vibration Isolators

The housing of MHD series with aluminum-magnesium alloy

Technical Date of MHD

MODEL LOAD LOAD DEFLECTION VERTICAL

OUTER SIZE (mm)

Weight to be supported by spring isolator(kg)

(2) LSBLGW500/C unit (mm)

Weight to be supported by spring isolator(kg)

Weight to be supported by spring isolator(kg)

(4) LSBLGW720/C unit (mm)

Weight to be supported by spring isolator(kg)

Weight to be supported by spring isolator（kg）

(6) LSBLGW1000/C unit (mm)

Weight to be supported by spring isolator（kg）

Weight to be supported by spring isolator（kg）

(8) LSBLGW1420/C unit (mm)

Weight to be supported by spring isolator（kg）

LSBLGW380/C BVR1204+BVR701 330A

LSBLGW500/C BVR2404+BVR1201 500A

LSBLGW1000/C 2* (BVR2404+BVR1201) 1000A