Aircraft Batteries: Secondary (Where They Can Be Recharged) - It Can Be Dangerous To Attempt
Aircraft Batteries: Secondary (Where They Can Be Recharged) - It Can Be Dangerous To Attempt
Aircraft Batteries: Secondary (Where They Can Be Recharged) - It Can Be Dangerous To Attempt
Aircraft batteries are used for many functions (e.g., ground power, emergency
power, improving DC bus stability, and fault clearing). Most small private aircraft
use lead acid batteries. Most commercial and corporate aircraft use nickel-
cadmium (Ni Cd) batteries. However, other lead acid types of batteries are
becoming available, such as the valve-regulated lead-acid (VRLA) batteries. The
battery best suited for a particular application depends on the relative
importance of several characteristics, such as weight, cost, volume, service or
shelf life, discharge rate, maintenance, and charging rate. Any change of battery
type may be.
Type of Batteries
Aircraft batteries are usually identified by the material used for the plates. The
two most common types of battery used are lead-acid and NiCd batteries.
Lead-Acid Batteries
Dry Charged Cell Lead Acid Batteries
Dry charged cell lead-acid batteries, also
known as flooded or wet batteries, are
assembled with electrodes (plates) that have
been fully charged and dried. The electrolyte is
added to the battery when it is placed in
By PR BHATIA
service, and battery life begins when the electrolyte is added. An aircraft storage
battery consists of 6 or 12 lead-acid cells connected in series. The open circuit
voltage of the 6 cell battery is approximately 12 volts, and the open circuit voltage
of the 12-cell battery is approximately 24 volts. Open circuit voltage is the voltage
of the battery when it is not connected to a load. When flooded (vented)
batteries are on charge, the oxygen generated at the positive plates escapes from
the cell. Concurrently, at the negative plates, hydrogen is generated from water
and escapes from the cell. The overall result is the gassing of the cells and water
loss. Therefore, flooded cells require periodic water replenishment.
When VRLA batteries are on charge, oxygen combines chemically with the lead at
the negative plates in the presence of H2SO4 to form lead sulphate and water.
This oxygen recombination suppresses the generation of hydrogen at the negative
plates. Overall, there is no water loss during charging. A very small quantity of
water may be lost as a result of self-discharge reactions; however, such loss is so
small that no provisions are made for water replenishment. The battery cells have
a pressure relief safety valve that may vent if the battery is overcharged
By PR BHATIA
The chemical reactions that occur in a lead-acid battery are represented by the
following equations:
As the cell is charged, the sulphuric acid (H2SO4) concentration increases and
becomes highest when the cell is fully charged. Likewise, when the cell is
discharged, the acid concentration decreases and becomes most dilute when the
cell is fully discharged. The acid concentration generally is expressed in terms of
specific gravity, which is weight of the electrolyte compared to the weight of an
equal volume of pure water.
The cell’s specific gravity can be estimated from its open circuit voltage using the
following equation:
Specific Gravity (SG)= Open Circuit Voltage (OCV)- 0.84
There are two basic cell types: vented and recombinant. Vented cells have a
flooded electrolyte, and the hydrogen and oxygen gases generated during
charging are vented from the cell container. Recombinant cells have a starved or
gelled electrolyte, and the oxygen generated from the positive electrode during
charging diffuses to the negative electrode where it recombines to form water by
the following reaction:
Pb + H2SO4 + 1/2O2 → PbSO4 + H2O
By PR BHATIA
The recombination reaction suppresses hydrogen evolution at the negative
electrode, thereby allowing the cell to be sealed. In practice, the recombination
efficiency is not 100% and a resalable valve regulates the internal pressure at a
relatively low value, generally below 10 psig. For this reason, sealed lead-acid
cells are often called “valve-regulated lead-acid” (VRLA) cells.
Battery Construction
Lead-acid aircraft batteries are constructed
using injection-molded, plastic monoblocs that
contain a group of cells connected in series.
Monoblocs typically are made of polypropylene,
but ABS is used by at least one manufacturer.
Normally, the monobloc serves as the battery
case, similar to a conventional automotive
battery.
By PR BHATIA
Temperature Effects and Limitations
Lead-acid batteries generally are rated at 25°C (77°F) and operate best
around this temperature. Exposure to low ambient temperatures results in
performance decline, whereas exposure to high ambient temperatures results
in shortened life.
The lower temperature limit is dictated by the freezing point of the
electrolyte. The electrolyte freezing point varies with acid concentration, as
shown in Table 10.1. The minimum freezing point is a chilly 70°C (95°F) at a
specific gravity (SG) of 1.30. Since fully charged batteries have SGs in the
range of 1.28 to 1.33, they are not generally susceptible to freezing even under
extreme cold conditions. However, when the battery is discharged, the SG
drops and the freezing point rises. At low SG, the electrolyte first will turn to
slush as the temperature drops. This is because the water content freezes first,
gradually raising the SG of the remaining liquid so that it remains unfrozen.
Solid freezing of the electrolyte in a discharged battery requires temperatures
well below the slush point; a practical lower limit of 30°C is often specified.
By PR BHATIA
Solid freezing can damage the battery permanently (i.e., by cracking cell
containers), so precautions should be taken to keep the battery charged or
heated when exposed to temperatures below 30°C.
The upper temperature limit is generally in the range of 60 to 70°C. Capacity
loss is accelerated greatly when charged above this temperature range due to
vigorous gassing and/or rapid grid corrosion. The capacity loss generally is
irreversible when the battery is cooled.
Service Life
The service life of a lead-acid aircraft battery depends on the type of use it
experiences (e.g., rate, frequency, and depth of discharge), environmental
conditions (e.g., temperature and vibration), charging method, and the care
with which it is maintained. Service lives can range from 1 to 5 years,
depending on the application. Table 10.2 shows representative life cycle data
as a function of the depth of discharge. Manufacturers’ data should be
consulted for specific batteries of interest.
NiCd Batteries
A NiCd battery consists of a metallic box, usually stainless steel, plastic-coated
steel, painted steel, or titanium containing a number of individual cells. These
cells are connected in series to obtain 12 volts or 24 volts. The cells are
connected by highly conductive nickel copper links. Inside the battery box, the
cells are held in place by partitions, liners, spacers, and a cover assembly. The
battery has a ventilation system to allow the escape of the gases produced
during an overcharge condition and provide cooling during normal operation.
NiCd cells installed in an aircraft battery are typical of the vented cell type.
The vented cells have a vent or low pressure release valve that releases any
generated oxygen and hydrogen gases when overcharged or discharged
rapidly. This also means the battery is not normally damaged by excessive
rates of overcharge, discharge, or even negative charge. The cells are
rechargeable and deliver a voltage of 1.2 volts during discharge.
Aircraft that are outfitted with NiCd batteries typically have a fault protection
system that monitors the condition of the battery. The battery charger is the
unit that monitors the condition of the battery and the following conditions
are monitored.
1. Overheat condition
By PR BHATIA
2. Low temperature condition (below –40 °F)
3. Cell imbalance
4. Open circuit
5. Shorted circuit
If the battery charger finds a fault, it turns off and sends a fault signal to the
Electrical Load Management System (ELMS).
Theory of Operation
The chemical reactions that occur in a nickel-cadmium battery are represented by
the following equations
There are two basic cell types: vented and recombinant. Vented cells have a
flooded electrolyte, and the hydrogen and oxygen gases generated during
charging are vented from the cell container. Recombinant cells have a starved
electrolyte, and the oxygen generated from the positive electrode during charging
By PR BHATIA
Diffuses to the negative electrode where it recombines to form cadmium
hydroxide by the following reaction:
Cell Construction
The construction of nickel-cadmium cells varies significantly, depending on
the manufacturer. In general, cells feature alternating positive and negative
plates with separator layers interleaved between them, a potassium
hydroxide (KOH) electrolyte of approximately 30% concentration by weight
(specific gravity 1.30), and a prismatic cell container with the cell terminals
extending through the cover. The positive plate is impregnated with nickel
hydroxide and the negative plate is impregnated with cadmium hydroxide.
The most common plate structure is made of nickel powder sintered onto a
substrate of perforated nickel foil or woven screens. At least one
manufacturer (ACME) uses nickel-coated polymeric fibers to form the plate
structure. Cell containers typically are made of nylon, polyamide, or steel. One
main difference between vented cells and sealed (recombinant) cells is the
type of separator. Vented cells use a gas barrier layer to prevent gases from
diffusing between adjacent plates. Recombinant cells feature a porous
separator system that permits gas diffusion between plates.
Battery Construction
Nickel-cadmium aircraft batteries generally consist of a steel case containing
identical, individual cells connected in series. The number of cells depends on
the particular application, but generally 19 or 20 cells are used. The end cells
of the series are connected to the battery receptacle located on the outside of
the case. The receptacle is usually a two-pin, quick disconnect type; both
Cannon and elcon styles commonly are used. Cases are vented by means of
vent tubes or louvers to allow escape of gases produced during overcharge.
By PR BHATIA
Some battery designs have provisions for forced air cooling, particularly for
engine start applications. Thermostatically controlled heating pads sometimes
are employed on the inside or outside of the battery case to improve low
temperature performance. Power for energizing the heaters normally is
provided by the aircraft’s AC or DC bus. Temperature sensors often are
included inside the case to allow regulation of the charging voltage. In
addition, many batteries are equipped with a thermal switch that protects the
battery from overheating if a fault develops or if battery is exposed to
excessively high temperatures. A typical aircraft battery assembly is shown in
Figure.
Battery Charging
Operation of aircraft batteries beyond their ambient temperature or charging
voltage limits can result in excessive cell temperatures leading to electrolyte
boiling, rapid deterioration of the cells, and battery failure. The relationship
between maximum charging voltage and the number of cells in the battery is
also significant. This determines (for a given ambient temperature and state of
charge) the rate at which energy is absorbed as heat within the battery. For
lead-acid batteries, the voltage per cell must not exceed 2.35 volts. In the case
of NiCd batteries, the charging voltage limit varies with design and
construction. Values of 1.4 and 1.5 volts per cell are generally used. In all
cases, follow the recommendations of the battery manufacturer.
By PR BHATIA
The battery charging system in an airplane is of the constant voltage type. An
engine-driven generator, capable of supplying the required voltage, is
connected through the aircraft electrical system directly to the battery. A
battery switch is incorporated in the system so that the battery may be
disconnected when the airplane is not in operation. The voltage of the
generator is accurately controlled by means of a voltage regulator connected
in the field circuit of the generator.
For a 12-volt system, the voltage of the generator is adjusted to approximately
14.25. On 24-volt systems, the adjustment should be between 28 and 28.5
volts. When these conditions exist, the initial charging current through the
battery is high. As the state of charge increases, the battery voltage also
increases, causing the current to taper down. When the battery is fully
charged, its voltage is almost equal to the generator voltage, and very little
current flows into the battery.
When the charging current is low, the battery may remain connected to the
generator without damage. When using a constant-voltage system in a battery
shop, a voltage regulator that automatically maintains a constant voltage is
incorporated in the system. A higher capacity battery (e.g., 42 Ah) has a lower
resistance than a lower capacity battery (e.g., 33 Ah). Hence, a high-capacity
battery draws a higher charging current than a low-capacity battery when
both are in the same state of charge and when the charging voltages are equal.
The constant voltage method is the preferred charging method for lead-acid
batteries.
By PR BHATIA
usually consists of a rectifier to change the normal AC supply to DC. A
transformer is used to reduce the available 110-volt or 220- volt AC supply to
the desired level before it is passed through the rectifier. If a constant current
charging system is used, multiple batteries may be connected in series,
provided that the charging current is kept at such a level that the battery does
not overheat or gas excessively.
The constant current charging method is the preferred method for charging
NiCd batteries. Typically, a NiCd battery is constant current charged at a rate
of 1CA until all the cells have reached at least 1.55V. Another charge cycle
follows at 0.1CA, again until all cells have reached 1.55V. The charge is
finished with an overcharge or top-up charge, typically for not less than 4
hours at a rate of 0.1CA. The purpose of the overcharge is to expel as much, if
not all the gases collected on the electrodes, hydrogen on the anode, and
oxygen on the cathode; some of these gases recombine to form water that, in
turn, raises the electrolyte level to its highest level after which it is safe to
adjust the electrolyte levels.
Thermal runaway
NiCd batteries are capable of performing to its rated capacity when the
ambient temperature of the battery is in the range of approximately 60–90 °F.
An increase or decrease in temperature from this range results in reduced
By PR BHATIA
capacity. NiCd batteries have a ventilation system to control the temperature
of the battery. A combination of high battery temperature (in excess of 160 °F)
and overcharging can lead to a condition called thermal run away. The
temperature of the battery has to be constantly monitored to ensure safe
operation. Thermal runaway can result in a NiCd chemical fire and/or
explosion of the NiCd battery under recharge by a constant-voltage source and
is due to cyclical, ever-increasing temperature and charging current. One or
more shorted cells or an existing high temperature and low charge can
produce the following cyclical sequence of events:
1. Excessive current,
2. Increased temperature,
3. Decreased cell(s) resistance,
4. Further increased current, and
5. Further increased temperature
Storage Characteristics
Nickel-cadmium batteries can be stored in any state of charge and over a broad
temperature range (i.e., -65 to 60°C). For maximum shelf life, however, it is best
to store batteries between 0 and 30°C. Vented cell batteries normally are stored
with the terminals shorted together. Shorting of sealed-cell batteries during
storage is not recommended, however, since it may cause cell venting and/or cell
reversal.
When left on open circuit during periods of non-operation, nickel-cadmium
batteries will self-discharge at a relatively fast rate. As a rule of thumb, the self
By PR BHATIA
discharge rate of sealed cells is approximately 1%/day at 20°C (when averaged
over 30 days), and the rate increases by 1%/day for every 10°C rise in
temperature (e.g., 2%/day at 30°C, 3%/day at 40°C, etc.). The self-discharge rate
is somewhat less for vented cells. The capacity lost by self-discharge usually is
recoverable when charged in the normal fashion.
Battery Maintenance
Battery inspection and maintenance procedures vary with the type of chemical
technology and the type of physical construction. Always follow the battery
manufacturer’s approved procedures. Battery performance at any time in a given
application depends upon the battery’s age, state of health, state of charge, and
mechanical integrity, which you can determine according to the following:
• To determine the life and age of the battery, record the install date of the
battery on the battery. During normal battery maintenance, battery age must be
documented either in the aircraft maintenance log or in the shop maintenance
log.
• Lead-acid battery state of health may be determined by duration of service
interval (in the case of vented batteries), by environmental factors (such as
excessive heat or cold), and by observed electrolyte leakage (as evidenced by
corrosion of wiring and connectors or accumulation of powdered salts). If the
battery needs to be refilled often, with no evidence of external leakage, this may
indicate a poor state of the battery, the battery charging system, or an overcharge
condition.
By PR BHATIA
generator or alternator restores a battery to full charge during a flight of 1 hour to
90 minutes.
• Proper mechanical integrity involves the absence of any physical damage, as
well as assurance that hardware is correctly installed and the battery is properly
connected. Battery and battery compartment venting system tubes, nipples, and
attachments, when required, provide a means of avoiding the potential buildup of
explosive gases, and should be checked periodically to ensure that they are
securely connected and oriented in accordance with the maintenance manual’s
installation procedures. Always follow procedures approved for the specific
aircraft and battery system to ensure that the battery system is capable of
delivering specified performance.
2. Inspect battery terminals and quickly disconnect plugs and pins for evidence of
corrosion, pitting, arcing, and burns. Clean as required.
3. Inspect battery drain and vent lines for restriction, deterioration, and security.
4. Routine pre flight and post flight inspection procedures should include
observation for evidence of physical damage, loose connections, and electrolyte
loss.
Installation Practices
• External surface—Clean the external surface of the battery prior to installation
in the aircraft.
• Replacing lead-acid batteries—When replacing lead-acid batteries with NiCd
batteries, a battery temperature or current monitoring system must be installed.
Neutralize the battery box or compartment and thoroughly flush with water and
dry. A flight manual supplement must also be provided for the NiCd battery
installation. Acid residue can be detrimental to the proper functioning of a NiCd
battery, as alkaline is to a lead-acid battery.
By PR BHATIA
Venting systems often use ram pressure to flush fresh air through the battery
case or enclosure to a safe overboard discharge point. The venting system
pressure differential should always be positive and remain between
recommended minimum and maximum values. Line runs should not permit
battery overflow fluids or condensation to be trapped and
prevent free airflow.
• Battery sump jars—A battery sump jar installation may be incorporated in the
venting system to dispose of battery electrolyte overflow. The sump jar should
be of adequate design and the proper neutralizing agent used. The sump jar must
be located only on the discharge side of the battery venting system.
• Installing batteries—When installing batteries in an aircraft, exercise care to
prevent inadvertent shorting of the battery terminals. Serious damage to the
aircraft structure (frame, skin and other subsystems, avionics, wire, fuel, etc.) can
be sustained by the resultant high discharge of electrical energy. This condition
may normally be avoided by insulating the terminal posts during the installation
process. Remove the grounding lead first for battery removal, then the positive
lead. Connect the grounding lead of the battery last to minimize the risk of
shorting the hot terminal of the battery during installation.
By PR BHATIA
By PR BHATIA
By PR BHATIA