535 Pipe and Bolt

Threading Machine
OPERATOR’S
MANUAL
• Pour français voire page 17
• Para ver el castellano vea
la página 35

IMPORTANT
For your own safety, before
assembling and operating this
unit, read this Operator’s
Manual carefully and com-
pletely. Learn the operation,
applications and potential
hazards peculiar to this unit.
 535 Pipe and Bolt Threading Machine

Table of Contents
General Safety Information
Work Area Safety........................................................................................................................................................2
Electrical Safety ..........................................................................................................................................................2
Personal Safety ..........................................................................................................................................................2
Tool Use and Care......................................................................................................................................................3
Service........................................................................................................................................................................3
Specific Safety Information
Foot Switch Safety......................................................................................................................................................3
Machine Safety ..........................................................................................................................................................4
Description, Specifications and Accessories
Description..................................................................................................................................................................4
Specifications..............................................................................................................................................................4
Accessories ................................................................................................................................................................5
Setup Instructions
Assembling Leg Stands ..............................................................................................................................................6
Mounting Machine on Bench ......................................................................................................................................6
Operation Using Machine Mounted Tools
Checking Oil System ..................................................................................................................................................6
Installing Pipe ............................................................................................................................................................6
Cutting Pipe with No. 820 Cutter ................................................................................................................................6
Reaming Pipe with No. 341 Reamer ..........................................................................................................................7
Threading Pipe or Rod with Quick-Opening or Self-Opening Die Head ....................................................................7
Installing Dies in Quick-Opening Die Head (Right Hand & Left Hand) ......................................................................7
Installing Dies in Self-Opening Die Head (Right Hand Only)......................................................................................8
Operation Using Geared Threaders
Installing No. 141 Geared Threader (Closed-Coupled Method) ................................................................................8
Threading Pipe Using No. 141 Geared Threader (Close Coupled Method) ............................................................10
Setting Up Nos. 141 &161 Geared Threaders Using No. 840A Universal Drive Shaft ............................................11
Threading Pipe Using Nos. 141 & 161 Geared Threaders with No. 840A Universal Drive Shaft ............................11
Adjusting Nos. 141 & 161 Geared Threaders
Cam Plate (Pipe Size) Adjustment Procedure..........................................................................................................12
Thread Size Adjustment Procedure..........................................................................................................................12
Changing Posts for Straight or Tapered Threads ....................................................................................................12
Changing Die Set......................................................................................................................................................12
No. 819 Nipple Chuck
Short or Close Nipple Threading Procedure ............................................................................................................13
Checking Thread Length ..........................................................................................................................................13
Maintenance Instructions
Lubrication ................................................................................................................................................................14
Oil System Maintenance ..........................................................................................................................................14
Jaw Insert Replacement ..........................................................................................................................................14
Motor Brush Replacement ........................................................................................................................................14
Wiring Diagrams ........................................................................................................................................................15
Lifetime Warranty ........................................................................................................................................Back Cover

ii Ridge Tool Company • Elyria, Ohio • U.S.A.

535
Pipe and Bolt Threading
Machine

IMPORTANT
For your own safety, before
assembling and operating this
unit, read this Operator’s
Manual carefully and com- 535 Pipe and Bolt Threading Machine
pletely. Learn the operation, Record Serial Number below and retain product serial number which is located on nameplate.
applications and potential haz-
ards peculiar to this unit. Serial
No.
 535 Pipe and Bolt Threading Machine

General Safety Information 4. Do not abuse cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep
cord away from heat, oil, sharp edges or moving
WARNING
parts. Replace damaged cords immediately.
Read and understand all instructions. Failure to
Damaged cords increase the risk of electrical shock.
follow all instructions listed below may result in
electric shock, fire, and/or serious personal 5. When operating a power tool outside, use an
injury.
outdoor extension cord marked “W-A” or “W”.
These cords are rated for outdoor use and reduce
SAVE THESE INSTRUCTIONS! the risk of electrical shock.
6. Connect the tool to an AC power supply that
Work Area Safety matches the name plate specification. Incorrect
1. Keep your work area clean and well lit. Cluttered voltage supply can cause electrical shock or burns.
benches and dark areas invite accidents. 7. Use only three-wire extension cords which
2. Do not operate power tools in explosive atmos- have three-prong grounding plugs and three-
pheres, such as in the presence of flammable pole receptacles which accept the machines
liquids, gases, or dust. Power tools create sparks plug. Use of other extension cords will not ground
which may ignite the dust or fumes. the tool and increase the risk of electrical shock.
3. Keep bystanders, children, and visitors away 8. Use proper extension cords. (See chart.) Insuf-
while operating a power tool. Distractions can ficient conductor size will cause excessive voltage
cause you to lose control. drop, loss of power and overheating.
4. Do not let visitors contact the tool or extension Minimum Wire Gauge for Cord Set
cord. Such preventative measures reduce the risk Nameplate
Total Length (in feet)
of injury. Amps
0 – 25 26 – 50 51 – 100
Electrical Safety 0–6 18 AWG 16 AWG 16 AWG
6 – 10 18 AWG 16 AWG 14 AWG
1. Grounded tools must be plugged into an outlet,
10 – 12 16 AWG 16 AWG 14 AWG
properly installed and grounded in accordance
12 – 16 14 AWG 12 AWG NOT RECOMMENDED
with all codes and ordinances. Never remove
the grounding prong or modify the plug in any
way. Do not use any adapter plugs. Check with Personal Safety
a qualified electrician if you are in doubt as to 1. Stay alert, watch what you are doing and use
whether the outlet is properly grounded. If the common sense when operating a power tool.
tools should electrically malfunction or break down, Do not use tool while tired or under the influ-
grounding provides a low resistance path to carry ence of drugs, alcohol, or medications. A
electricity away from the user. moment of inattention while operating power tools
Cover of may result in serious personal injury.
grounded
outlet box
2. Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught
in moving parts.
Grounding pin Grounding pin
3. Avoid accidental starting. Be sure switch is off
2. Avoid body contact with grounded surfaces before plugging in. Carrying tools with your finger
such as pipes, radiators, ranges and refrigera- on the switch or plugging in tools that have the
tors. There is an increased risk of electrical shock switch on invites accidents.
if your body is grounded. 4. Remove adjusting keys or switches before
3. Don’t expose power tools to rain or wet condi- turning the tool ON. A wrench or a key that is left
tions. Water entering a power tool will increase the attached to a rotating part of the tool may result in
risk of electrical shock. personal injury.

2 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

5. Do not overreach. Keep proper footing and Service

balance at all times. Proper footing and balance
enables better control of the tool in unexpected 1. Tool service must be performed only by quali-
situations. fied repair personnel. Service or maintenance
performed by unqualified repair personnel could
6. Use safety equipment. Always wear eye pro- result in injury.
tection. Dust mask, non-skid safety shoes, hard
hat, or hearing protection must be used for appro- 2. When servicing a tool, use only identical
priate conditions. replacement parts. Follow instructions in the
Maintenance Section of this manual. Use of unau-
Tool Use and Care thorized parts or failure to follow maintenance
instructions may create a risk of electrical shock
1. Use clamp or other practical way to secure and or injury.
support the workpiece to a stable platform.
Holding the work by hand or against your body is 3. Follow instructions for lubricating and chang-
unstable and may lead to loss of control. ing accessories. Accidents are caused by poorly
maintained tools.
2. Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed. Specific Safety Information
3. Do not use tool if switch does not turn it ON or The Operator’s Manual contains specific safety infor-
OFF. Any tool that cannot be controlled with the mation and instructions for your protection against
switch is dangerous and must be repaired. serious injuries including:
4. Disconnect the plug from the power source • Loss of fingers, hands, arms or other body parts if
before making any adjustments, changing clothing or gloves get caught in moving parts;
accessories, or storing the tool. Such preven-
• Electrical shock or burns from contact with wires,
tive safety measures reduce the risk of starting the
motor or other power drive parts;
tool accidentally.
• Impact injuries, including broken bones if machine
5. Store idle tools out of the reach of children and
tips over or workpiece falls;
other untrained persons. Tools are dangerous in
the hands of untrained users. • Eye injuries, including being blinded by the work-
piece or workpiece chips.
6. Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are Read and follow safety labels on machine!
easier to control. Know the location and functions
of all controls before using this tool.
7. Check for misalignment or binding of moving
parts, breakage of parts, and any other condi-
tion that may affect the tool's operation. If dam- Foot Switch Safety
aged, have the tool serviced before using. Many The foot switch is for your safety. It lets you SHUT
accidents are caused by poorly maintained tools. OFF the motor by removing your foot. If clothing
8. Use only accessories that are recommended by should become caught in the machine, it will con-
the manufacturer for your model. Accessories tinue to wind up, pulling you into the machine.
that may be suitable for one tool may become haz- Because the machine has high torque, the cloth-
ardous when used on another tool. ing itself can bind around your arm or other body
parts with enough force to crush or break bones.
9. Inspect tool and extension cords periodically
and replace if damaged. Damaged cords increase
the risk of electrical shock.
10. Keep handles dry and clean; free from oil and
grease. Allows for better control of the tool.
11. Store tools in dry place. Such measures reduce
the risk of electrical shock.

Ridge Tool Company • Elyria, Ohio • U.S.A. 3

 535 Pipe and Bolt Threading Machine

6. Do not use machine if foot switch is broken. Foot

▲ WARNING switch is a safety device to prevent serious injury.
7. Tighten chuck handwheel and engage rear cen-
tering device on the pipe before turning on the
machine. Prevents oscillation of the pipe.
8. Lock foot switch when not in use (Figure 1).
Avoids accidental starting.

Clothing/gloves can be caught in moving parts.

Fingers, hands, arms or other body parts can be
crushed or broken.

• Use foot switch.

• Do not wear gloves.
Figure 1 – Locked Foot Switch
• Keep sleeves and jacket buttoned.
• Do not reach across machine because clothing SAVE THESE INSTRUCTIONS!
can be drawn into moving parts.
• Operate machine from switch side only. Description, Specifications and
• Do not block or disconnect foot switch. Accessories
• Keep foot switch in working order. Description
• Make sure you can quickly remove your foot from The RIDGID No. 535 Pipe and Bolt Threading
the foot switch. Machine is an electric motor-driven machine which
centers and chucks the pipe, conduit and rod (bolt
• Keep hands away from rotating pipe and fittings.
stock), and rotates it while threading, cutting, and
Stop machine when screwing fittings on pipe or
reaming operations are performed. Left-hand or right-
wiping thread.
hand rotation can be selected with FOR/OFF/REV
• Do not use this machine to make or break fittings. switch. Threading dies are mounted in self-opening or
quick-opening die heads. An automatic oiling system
READ ABOVE WARNING CAREFULLY!
is provided to flood the work with thread cutting oil
during threading operations.
Threading Machine Safety
1. Machine is made to thread and cut pipe or bolt. Specifications
Follow instructions in Operator’s Manual on machine Threading Capacity .......Pipe 1/8″ through 2″
uses. Other uses may increase the risk of injury. Bolt 1/4″ through 2″
2. Secure machine to bench or stand. Will keep the Cutter ............................No. 820 - Roll-type cutoff, self-
machine from tipping over. centering, full floating, pipe 1/8″
3. Keep covers in place. Do not operate the ma- through 2″, bolt 1/4″ through 1″
chine with covers removed. Exposure to moving or
parts may result in entanglement and serious injury.
No. 821 - Blade-type cutoff,
4. Support long heavy pipe with pipe supports. self-centering, full floating,
Will prevent tipping of the machine. pipe 1/2″ through 2″, dovetail-
5. Do not wear gloves or loose clothing. Keep type cutoff and chamfering
sleeves and jackets buttoned. Do not reach tool.
across the machine or pipe. Clothing can be Reamer..........................No. 341 - Positive-locking,
caught by the pipe resulting in entanglement and 5-flute cone, right hand,
serious injury. 1
/8″ through 2″

4 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

Chuck ............................RIDGID Speed Chuck Stands:

Rear Centering Device....Scroll operated, rotates with No. 100 ...................4 legs w/tray
chuck No. 150 ...................2 wheels w/tray
No. 200 .....................2 wheels w/enclosed cabinet
Pump .............................Gerotor-type, self-priming
No. 819 Nipple Chuck (Right Hand only):
Switch FOR/OFF/REV....Heavy-duty, rotary type,
bump-proof mounted Pipe Adapters ...........1/8″ through 11/2″
Stud Adapters..........1/4″ through 2″ UNC
Foot Switch....................ON/OFF motor control 1
/4″ through 11/2″ UNF
Motor .............................Universal type, NOTE! No. 819 Nipple Chuck is used for threading
1
/2 HP, 115v, Single phase AC close nipples
(50-60 Hz only)
Threading pipe w/geared threader close-coupled
230v available on request
method
1 Gallon NuClear Oil No. 768 Drive Link Assembly & No. 844 Drive
NOTE! Use of RIDGID Thread Cutting Oil is essential for Bar…adapt No. 141 geared threader
producing high quality threads and maximizing No. 141 Geared Threader…for threading 21/2″ – 4″
die life. For information concerning its use and
handling, refer to the labels on the oil contain- pipe
ers. Disposal of the oil should be in accordance No. 46 Pipe Support Stand…adjustable 23″ to 33″
with government regulations.
Threading pipe w/geared threader using drive shaft
Weight with Standard
No. 840A Universal Drive Shaft…41″ closed, 50”
Equipment .....................275 lbs.
extended
(Less Die Heads & Dies)
No. 450 Tristand Chain Vise
Accessories No. 318 Oiler…required to keep dies flooded with oil
Die Head Racks: No. 92 Adjustable Pipe Support…adjustable 32″ to 41″
4U ...........................holds 4 heads Nos. 4PJ & 141 Geared Threaders…threading 21/2″
to 4″ pipe
6U ...........................holds 6 heads
No. 161 Geared Threader…threading 4″ to 6″ pipe
Pipe Supports:
VJ-99 ......................281/4″ – 521/2″
RJ-99 ......................301/2″ – 543/4″

Die Heads and Dies

Die Head Capacity Sets of Dies Capacity
Model No. Pipe Bolt Pipe Bolt R.H L.H. Special Notes
815A 1
/8″ - 2″ 1
/4″ - 2″ 4 1
/4″- 2″ X Self-opening die head
811A 1
/8″ - 2″ 1
/4″ - 2″ 4 /4″ - 2″
1
X Quick-opening die head
842 1
/4″ - 2″ 3 X Quick-opening die head
555 1
/8″ - 3/4″ 3 X Quick-opening die head
Mono R.H. 1
/8″ - 2″ 9 X Quick-opening die head
1
/4″ - 1″ 10 UNC Alloy or high speed dies,
531 X X
UNC or UNF
10 UNF
Quick-opening die head
Alloy or high speed dies,
532 11/8″ - 2″ 6 UNC X X UNC or UNF
4 UNF Quick-opening die head
American National Series (High Speed) dies (8 T.P.I. 11/8″ - 21/2″)
(12 T.P.I. 1/2″ - 21/2″), and (16 T.P.I. 13/16″ - 21/2″)
General purpose Acme and Metric dies for 531 and 532 bolt die heads available on request.

Ridge Tool Company • Elyria, Ohio • U.S.A. 5

 535 Pipe and Bolt Threading Machine

38″
291/2″ Installing Pipe
1. Measure and mark length of pipe to be worked.
121/4″
173/4″ 2. If pipe is long enough to be retained by centering
6 /8″
1
15 /8″
5 device, insert pipe through front or rear of machine.
If pipe is short, insert into front of machine.
NOTE! For long lengths, support the end of the pipe with
Center LIne a RIDGID Adjustable Pipe Support.
141/2″ 3. Make certain that pipe is centered in centering
91/4″ device, if used, and tighten centering device.
4. Tighten chuck jaws with a repetitive counter-clock-
383/4″O.A.L. wise snap spin of handwheel. This hammering
Figure 2 – No. 535 Machine Dimensions action tightens jaws on pipe. A clockwise rotation
snap spin releases jaws.
Setup Instructions Quick or Self-
The RIDGID No. 535 Pipe and Bolt Threading Machine is Opening Die Head
Centering
designed to be bench or stand mounted. Four stands are Device No. 820 Cutter
Chuck Handwheel (Standard)
available including a Leg Stand with Tray, Wheel Stand
with Tray, and Wheel Stand with Enclosed Cabinet. No. 341
Reamer
Assembling Leg Stands REV/OFF/FOR
Refer to 535 Parts List and stand assembly instruction Switch
sheet. Chip
Pan

Mounting Machine on Bench

To mount the unit on a bench, use four 3/8″ bolts in
holes provided at each corner of machine base. Base Carriage Length
dimensions are shown in Figure 2. Handwheel Gauge
Foot Switch
Figure 3 – No. 535 Pipe and Bolt Threading Machine
Operation Using
Machine Mounted Tools Cutting Pipe with No. 820 Cutter
(Figure 3)
WARNING 1. Swing reamer and die head to UP position.
Operator should be thoroughly familiar with pre-
ceding Safety Precautions before attempting to 2. Move pipe cutter DOWN onto pipe and move car-
operate this equipment. riage with handwheel to line up cutter wheel with
mark on pipe.
Checking Oil System NOTE! If using length gauge on machine carriage, place
(Figure 3) cutter wheel against end of stock and set point to
“0”. Raise cutter to clear stock and turn carriage
1. Set up machine on stand or bench. handwheel until pointer is at length desired.
2. Slide chip pan out of base. 3. Tighten cutter feed screw handle on pipe.
3. Fill reservoir in base with approximately 5 quarts 4. Turn REV/OFF/FOR to FOR (forward) position and
of RIDGID Thread Cutting Oil. step on foot switch.
4. Plug power cord into outlet. Voltage of outlet 5. Continuously turn cutter feed screw handle with
must be the same as voltage indicated on tag and both hands until pipe is cut off.
name plate.
NOTE! For cutting larger sizes of rod, flow of oil can be
5. Turn switch to FOR (forward) position. directed to the Cutter by using old style oil
spout/pivot plug.
6. Step on foot switch

6 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

6. Release foot switch and turn REV/OFF/FOR (1/4″ - 3/8″), (1/2″ - 3/4″), and (1″ - 2″). The 1/8″ pipe dies are
switch to OFF position. not available for left-hand die head. Bolt threading
requires a separate set of dies for each bolt size. No bolt
7. Return pipe cutter to UP position.
dies are available for left-hand universal die heads.
Reaming Pipe with No. 341 Reamer 1. Lay die head on bench with numbers up.
(Figure 3) 2. Flip throwout lever to OPEN position.
1. Move reamer arm into DOWN position. 3. Loosen clamp lever approximately three turns.
2. Extend reamer by pressing latch and sliding knob 4. Lift tongue of clamp lever washer up out of slot
toward pipe until latch engages bar. under size bar. Slide throwout lever all the way
3. Turn REV/OFF/FOR switch to FOR position and to end of slot in the OVER direction indicated on
step on foot switch. size bar (in direction of CHANGE DIES arrow on
rear of cam plate).
4. Position reamer into pipe and complete reaming by
exerting pressure on handwheel. 5. Remove worn dies from die head.
5. Release foot switch and turn REV/OFF/FOR 6. Insert new dies to mark on side of dies. Die num-
switch to OFF position. bers 1 through 4 must agree with those on die head.
6. Retract reamer bar and return reamer to UP posi- 7. Slide throwout lever back so that tongue of clamp
tion. lever washer will drop in slot under size bar.
8. Adjust die head size bar until index line on lock
Threading Pipe or Rod with Quick- screw or link is aligned with proper size mark on
Opening or Self-Opening Die Head size bar. For bolt threads, align index line with
1. Install die set. Refer to die installation procedure. BOLT line on size bar.
2. Swing cutter and reamer to UP position. 9. Tighten clamp lever.
3. Swing die head to DOWN position with throwout 10. If oversize or undersize threads are required, set
lever set to CLOSE position. the index line in direction of OVER or UNDER size
mark on size bar.
4. Turn REV/OFF/FOR switch to FOR position and
step on foot switch. Washer
Index Line
5. Turn carriage handwheel to bring dies against end
of pipe. Slight pressure on handwheel will start dies.
6. Quick-Opening Die Head (Figure 4) – When thread Head
is completed, rotate throwout lever to OPEN posi-
tion, retracting dies. Link

Self-Opening Die Head (Figure 5) – When die

head trigger contacts end of pipe, throwout lever
is automatically opened. Throwout Clamp Lever
Lever
7. Release foot switch and turn REV/OFF/FOR
switch to OFF position. Size Bar

8. Turn carriage handwheel to back die head off pipe.

9. Swing die head back to UP position. Figure 4 – Quick-Opening Die Head

Installing Dies in Quick-Opening Die

Head (Right Hand & Left Hand) Installing Dies in Self-Opening Die Head
(Right Hand only)
The No. 811A Quick-Opening Die Head (Figure 4) for
right-hand threads requires four sets of dies to thread The No. 815A Self-Opening Die Head (Figure 5) for
pipe ranging from 1/8″ through 2″. One set of dies is right-hand threads requires four sets of dies to thread
required for each of the following pipe size ranges: (1/8″), pipe ranging from 1/8″ - 2″. One set of dies is required

Ridge Tool Company • Elyria, Ohio • U.S.A. 7

 535 Pipe and Bolt Threading Machine

for each of the following pipe size ranges: (1/8″), (1/4″ -

3
/8″), (1/2″ - 3/4″), and (1″ - 2″). Bolt threading requires a Roll Pin
Size Bar

separate set of dies for each bolt size.

1. Place self-opening die head on bench in vertical Index Line
position.
2. Make sure trigger assembly is released.
Lock Screw
3. Loosen clamp lever approximately six turns.
4. Pull lock screw out of slot under size bar so that roll
pin in lock screw will by-pass slot. Position size bar
so that index line on lock screw is all the way to the
end of REMOVE DIES position. Clamp
Lever
5. Lay head down with numbers up.
Throwout
6. Remove worn dies from die head. Lever
7. Insert dies to mark on sides of dies. Die numbers 1
through 4 must agree with those on die head.
8. Rotate cam plate lever back to lock dies in head.
9. With head in vertical position, rotate cam plate until
roll pin on lock screw can be positioned in slot
under size bar. In this position dies will lock in die
head. Make sure roll pin points toward end of size
bar marked REMOVE DIES. Trigger
Assembly
10. Adjust die head size bar until index line on lock
Figure 5 – Self-Opening Die Head
screw of link is aligned with proper size marks on
size bar. For bolt threads, align index line with
BOLT line on size bar.
Operation Using Geared
11. Tighten clamp lever. Threaders
12. If oversize or undersize threads are required, set
WARNING
the index line in direction of OVER or UNDER size
Operator should be thoroughly familiar with pre-
mark on size bar.
ceding Safety Precautions before attempting to
operate this equipment.

Installing No. 141 Geared Threader

(Close-Coupled Method)
Threading pipe with a No. 141 Geared Threader
(closed coupled method) requires a No. 768 Drive
Link Assembly, No. 844 Drive Bar, and RIDGID Pipe
Support Stand.

8 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

Guide Post 8), which includes pipe nipple E-811, 90 degree

Head
elbow E-812, with coolant nozzle E-810 and 44340
Reference Pivot Plug and “O” rings.
Lines (3)

Drive Shaft
New-style 535: multi-position oil spout is attached
to E-814-x drive link (Figures 10A, B).
Coolant Nozzle

Drive Link
(Do not Install)

Elbow

Pipe Nipple
Cam Plate
Knob (2) Clamp Screw Figure 8 – Oil Spout used with Geared Threader
Close Coupled Method (Old Style 535)
Figure 6 – No. 141 Geared Threader with Drive Shaft Up
(No. 161 Threader Similar). NOTE! No. 768 drive link assembly includes: drive link E-
814-X, coolant nozzle E-810, pipe nipple E-811, 90
Selector Die (Set of 5) degree elbow E-812, pipe w/coupling E-1178-X,
Plate Guide
Die Head Block set screw E-2978. 44340 pivot plug, 44470 “O”
rings.
2T Under
Stop Line 7. Install No. 844 Drive Bar (Figure 9) onto 141
Screw
Standard Geared Threader Drive Shaft and tighten two set
Red Stop LIne screws, using 5/16″ socket head wrench.
Line
2T Over
Standard Line
Line
Guide Post Set Screw (2) No. 844 Drive Bar
Pinion
Sleeve Screw 141 Geared Threader

Drive Shaft
Gear Case

Drive LInk

Set Screw E-2978

Figure 7 – No. 141 Geared Threader showing Pinion
Sleeve and Guide Post Reference Lines
Figure 9 – No. 844 Drive Bar and Drive Link Installed
WARNING
Do not plug power cord in until geared threader 8. Insert Drive Link E-814-X into loop hole on 141
is installed and ready to thread.
geared threader. Using a 1/4″ socket head wrench,
tighten Set Screw E-2978 only enough to retain
1. Remove die head from machine.
drive link E-814-X, allowing it to swing freely.
2. Raise cutter and reamer out of way and move car-
9. Raise 141 Geared Threader and set on carriage.
riage to front.
Resting 141 Geared Threader on carriage, move
3. Open front chuck jaws and workholder jaws. carriage rearward and engage No. 844 Drive Bar in
535 front chuck and rear centering device.
4. Old-style 535: Install replacement oil spout (Figure

Ridge Tool Company • Elyria, Ohio • U.S.A. 9

 535 Pipe and Bolt Threading Machine

10. Align grooves on No. 844 Drive Bar (Figure 9) with

front chuck jaws and grip securely, using chuck
handwheel and workholder centering head.

WARNING
Be sure that No. 844 Drive Bar is properly en-
gaged and secured.

11. Supporting 141 Geared Threader, move Carriage

and fully engage Drive Link Assembly E-814-X in
die head mounting hole on carriage. Tighten set
screw E-2978.
12. If using No. 46 Pipe Support raise No. 46 Pipe
Support Stand Posts (Figure 11) by modifying,
using pipe w/coupling E-1178-X. Release adjusting
collar and position upper post rollers in line with
141 Geared Threader. Lock adjusting collar. Figure 10B – 141 Geared Threader Closed-Coupled to
New-Style 535 Showing Position of OIl
WARNING Spout on Work Piece.
If pipe extends beyond machine bed, it should
have a pipe support. Be sure that adjusting col- Release Roller (4)
lar on pipe support stand is locked securely.
➔ Upper Post
Adjusting Collar
➔

Pipe with
Lock Coupling
E-1178-X

Lower Post
Base

Figure 11 – No. 46 Pipe Support with Coupling

CAUTION
If, by accident a RIDGID geared threader is
backed off too far and threaded barrel becomes
disengaged from workholder, the threader must
be put on a bench and the threads re-engaged
carefully by hand. Do not attempt this by power.

Threading Pipe Using No. 141 Geared

Threader (Close Coupled Method)
1. Install geared threader and pipe.
Figure 10A – 141 Geared Threader Close-Coupled to 2. Plug in power cord.
New-Style 535 Using 768 Drive Link. Note
Oil Spout Attached to E-814-X Link. 3. Turn power drive REV/OFF/FOR switch to FOR
position. (Figure 3)
4. Step on foot switch.
5. Flood dies through oil spout (Figures 8 and 10),
with RIDGID Thread Cutting Oil during threading
operation to assure long die life.

10 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

6. Release foot switch when red stop line appears 5. Tightly secure pipe in No. 450 Tristand Chain Vise.
on pinion sleeve. (Figure 7)
6. Support long piece of pipe with No. 92 Pipe Support.
NOTE! RIDGID geared threaders are jam proof designed
so that pinion shaft will automatically disengage 7. Position workholder so that a jaw is on top center
if threader is accidentally run on pipe past a full and slide threader onto pipe. Carefully center end
thread length. of pipe in throat of dies.
7. Turn REV/OFF/FOR switch (Figure 3) to REV 8. Tighten workholder clamp screw (Figure 6) securely.
(reverse) position.
9. Slip square socket of No. 840A Universal Drive
8. Step on foot switch and reverse threader one or Shaft over square end of threader drive shaft and
two revolutions. Turn REV/OFF/FOR switch to tighten 2 set screws.
OFF position.
NOTE! When properly positioned, sliding shank of uni-
9. Pull cam plate knobs (Figure 6) and rotate cam versal shaft should be approximately centered
plate as far as it will go towards CD mark on head to allow movement in either direction.
to disengage dies. 10. Position No. 318 Oiler directly under threader.
10. Loosen jaw clamp screw (Figure 6), turn workhold-
er to OPEN position and remove pipe. Threading Pipe Using Nos. 141 & 161
Geared Threaders with No. 840A
NOTE! Before threading next piece of pipe, run threader Universal Drive Shaft
head beyond STANDARD line on pinion sleeve
and then back to standard line. This movement 1. Install geared threader and pipe.
takes up slack in gearing for immediate response
when cutting next thread. 2. Plug in power cord.
3. With REV/OFF/FOR switch in REV position, step
Setting Up Nos. 141 & 161 Geared
on foot switch.
Threaders Using No. 840A Universal
Drive Shaft 4. Flood dies with RIDGID Thread Cutting Oil using
RIDGID 318 Oiler during threading operation to
WARNING assure long die life. 141 and 161 – Release foot
1. Do NOT plug in power cord until gear threader switch when red stop line appears on pinion
is installed and ready to thread.
sleeve. (Figure 7)
2. Chain vise must be securely anchored with jack
screw assembly and post to ceiling or bolted to NOTE! RIDGID geared threaders are jam proof designed
floor. Bench vises must be secured to a bench. so that pinion shaft will automatically disengage
if threader is accidentally run on pipe past a full
3. When threading pipe up to 5″ nominal the 450 thread length.
Tristand Vise can be used. However, when
threading 6″ nominal pipe a BC-610 or BC-810 5. Turn REV/OFF/FOR switch to FOR (forward)
Top Screw Bench Vise must be used. position to back geared threader off pipe.
NOTE! Do not loosen workholder until dies have been
FAILURE TO FOLLOW THESE
disengaged from pipe.
INSTRUCTIONS COULD RESULT IN THE
VISE TIPPING CAUSING SERIOUS INJURY. 141 and 161 – Step on foot switch and reverse
threader one or two revolutions. Pull knobs (Figure
Refer to Figure 12.
6) and rotate cam plate as far as it will go towards
1. Adjust threader being used. Refer to page 9 for CD mark on head to disengage dies.
Nos. 141 and 161 Threaders.
6. Turn REV/OFF/FOR switch to OFF position.
2. Slide long hexagon end of the 840A universal
7. Loosen 2 set screws (Figure 12) and remove uni-
drive shaft into rear centering device head and
versal drive shaft from threader.
through to front chuck of No. 535 machine.
NOTE! Do not loosen workholder until dies have been
3. Make certain that universal drive shaft is centered disengaged from pipe.
in centering device head and front chuck jaws;
141 and 161 – Loosen jaw clamp screw (Figure 6)
tighten securely.
and turn workholder to OPEN position. Remove
4. Locate chain vise in line, on same level, and threader.
approximately length of universal drive shaft away
8. Loosen chain vise and remove pipe.
from centering head device.

Ridge Tool Company • Elyria, Ohio • U.S.A. 11

 535 Pipe and Bolt Threading Machine

9. Open centering device head to release No. 840A Reference Line 1: Set bottom surface of die head
Universal Drive Shaft. at red standard line on pinion
sleeve.
WARNING
Reference Line 2: Set upper surface of die head
If by accident, a RIDGID geared threader is
backed off too far and threaded barrel becomes
which houses guide post even
disengaged from workholder, the threader must with center line at top end of
be put on a bench and the threads reengaged guide post.
carefully by hand. Do not attempt this by power.
Oversize Thread – For oversize (shallow thread) set
head at bottom line on guide post. This line is marked
(2T OVER).
Undersize Thread – For undersize (deep thread) set
No. 318 Oiler head at top line on guide post. This line is marked (2T
No. 141 UNDER).
Geared Threader
No. 840A Changing Posts for Straight or Tapered
Drive Shaft
Threads
(Figure 7)

Set 1. Adjust threader to cut standard size threads.

Centering Head Screw (2)
2. Remove screw from gear case at base of guide
post.
3. Pull guide post up until guide block attached to
selector plate is disengaged from angle slot in
Foot Switch guide post.
4. Turn guide post until straight slot faces inward
No. 450 Tristand for straight thread, or curved slot inward for
Chain Vise tapered thread.
Figure 12 – Threading Pipe using No. 840A Universal NOTE! Unit is now set to cut straight threads (NPSM or
Drive Shaft BSPP) or tapered threads (NPT or BSPT).
5. Engage guide block in slot and push guide post
Adjusting Nos. 141 and down into position.
161 Geared Threaders 6. Replace guide post screw.
Cam Plate (Pipe Size) Adjustment NOTE! If it becomes necessary to remove or replace the
Procedure guide block, the stamped number E-1997 on guide
block must be AGAINST selector plate. If stamped
1. Place threader on floor or workbench with drive number is visible you will cut an UNDERSIZE
shaft up. thread.
2. Pull cam plate knobs (Figure 6) and rotate cam
Changing Die Set
plate to desired pipe size markings on top of die
head. Release knobs when locating pins drop into 1. Remove stop screw (Figure 7) from selector plate.
holes in selector plate.
2. Pull Knobs (Figure 7) and rotate cam plate to CD
mark on top of die head.
Thread Size Adjustment Procedure
Grasp workholder and turn square end of drive Shaft 3. Remove worn die set (Figure 7) and insert new
or turn gear case by hand to respective reference die set.
lines on guide post. (Figure 7) NOTE! Be sure to replace complete die set and that die
numbers correspond with slot numbers.
Standard Size Thread – Either one of following 2 ref-
erence lines may be used: 4. Replace stop screw.

12 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

No. 819 Nipple Chuck Nipple Chuck

The RIDGID No. 819 Nipple Chuck is a quick and
easy tool for holding short and close nipples or studs Wrench
Insert
for threading. Adapter
Capacity: 1
/8″ to 2″ standard pipe (NPT)
1
/4″ to 2″ bolts or studs UNC or UNF
Pipe Adapters Stud Adapters
1
/8″, 1/4″, 3/8″, 1/2″, 1
/4″ to 2″ UNC
3
/4″, 1″, 11/4″, 11/2″ /4″ to 11/2″ UNF
1

Short or Close Nipple Threading

Procedure
Figure 13 – Installing Nipple Chuck Body and Adapter
WARNING
DO NOT start machine when chuck wrench is
engaged with adapter or release collar.
Nipple
1. Grip pipe in machine chuck. Thread and ream one Wrench
end and cut nipple to desired length.
2. Place nipple chuck body (Figure 13) in power drive
chuck, gripping jaw grooves. Release
Collar
3. Position insert (Figure 13) small end toward
adapter with 1/8″ to 3/4″ pipe; large end with 1″ pipe;
no insert 11/4″ pipe and up.
4. Select proper size nipple chuck adapter and
screw into nipple chuck (Figure 13) by hand.
Tighten with wrench.
5. Screw nipple (Figure 14) threaded on one end into Figure 14 – Installing Unfinished Nipple and Releasing
adapter by hand. Ream and thread other end. Finished Nipple with Wrench
6. Insert pin on end of wrench (Figure 14) into one of
holes in nipple chuck release collar and turn. Checking Thread Length
Remove threaded nipple by hand.
(Figure 15)
1. Thread is cut to proper length when end of pipe is
flush with edge of dies (A, Figure 15).
2. Die head is adjustable to obtain proper thread
diameter. If possible, threads should be checked
with a thread ring gage (B, Figure 15). A proper
thread is cut when end of pipe is plus or minus one
turn of being flush with face of ring gage.
NOTE! If a ring gage is not available, a fitting can be
used. This fitting should be representative of
those being used on the job. The pipe thread
should be cut to obtain 2 or 3 turns hand tight
engagement with fitting. If pipe thread is not
proper diameter the index line should be moved
in the OVER or UNDER size mark on size bar.
(refer to installing dies in die heads).

Ridge Tool Company • Elyria, Ohio • U.S.A. 13

 535 Pipe and Bolt Threading Machine

Die Die bottom of oil reservoir. To clean filter screen,

loosen the screw that secures filter to base and pull
Die Flush filter from oil line. Clean filter screen in solvent and
W With End W
of Pipe blow out with compressed air if available. Do not
Pipe operate machine with oil filter screen removed.
Pipe
Starting to Cut Thread Completed Thread Jaw Insert Replacement
A - Full Width Die Thread (Figure 16)
Thin Ring
Gage NOTE! When teeth on jaw inserts become worn and fail
to hold pipe or rod during operation, replace
D D D
entire set of jaw inserts. Clean teeth of jaw
inserts daily with wire brush.
Flush One Turn Large One Turn Small
(Basic Size) (Maximum Size) (Minimum Size)

B - Checking Threads Within Pipe Gage PRESS

DOWN
Figure 15 – Checking Thread Length

➔
Screw Driver

Maintenance Instructions
Insert
Locking Teeth
WARNING Pin
Always unplug power cord before servicing
machine. To Remove To Replace

Figure 16 – Jaw Insert Replacement

Lubrication
1. Place screw driver in insert slot and turn 90
Proper lubrication is essential to trouble-free operation
degrees in either direction.
and long life of threading machine.
2. Place insert sideways on locking pin and press
1. Remove three cover mounting screws and remove
down as far as possible.
the cover.
3. Hold insert down firmly with screwdriver, turn as
2. Use grease gun to apply grease to the shaft bear-
so teeth face up.
ing grease fittings every 2 to 6 months, depending
upon frequency of machine use.
Motor Brush Replacement
3. Apply moderate coat of lubricating grease on large
Check motor brushes every six (6) months and
gear each time bearings are lubricated.
replace brushes when they are worn to less than 1/2″.
If commutator is worn, turn outer dimensions of com-
WARNING mutator and undercut mica before replacing brushes.
Do not operate the threading machine with
cover off. Always replace cover immediately
after lubricating machine.

Oil System Maintenance

To help assure proper operation of threading
machine, keep oil system clean, as follows:
1. Replace thread cutting oil when it becomes dirty or
contaminated. To drain the oil, position a container
under drain plug and remove plug.
2. Keep oil filter screen clean to assure proper flow or
clean oil to work. Oil filter screen is located in the

14 Ridge Tool Company • Elyria, Ohio • U.S.A.

 535 Pipe and Bolt Threading Machine

1194 Motor (115V)

2394 Motor (230V)
1194A Motor (115V)

Blue
Suppressor Red
White (Blue) White
Black (Brown) Yellow

Green/Yellow
Green (Green/Yellow)

Black
Black
Black
115V
25-60 Hz IEC Standard
White
Green

REV
OFF

Foot Switch FWD

European Wiring Diagram

Ridge Tool Company • Elyria, Ohio • U.S.A. 15

 535 Pipe and Bolt Threading Machine

16 Ridge Tool Company • Elyria, Ohio • U.S.A.

 LIFETIME WARRANTY GARANTIE A VIE
The reputation of RIDGID® tools is the result of consistent product quality La renommée du matériel RIDGID® est le résultat d'une grande
and years of pride in workmanship. Rigorous checks and controls, from fiabilité des produits et de nombreuses années de fierté du tra-
raw materials to packaged products, ensure product confidence widely vail bien fait. Le contrôle approfondi et systématique des pro-
accepted as the benchmark of the professional trades. RIDGID® tools are duits, allant des matières premières aux produits finis, a
warranted to be free of defects in workmanship or material for the life of conféré à nos produits la réputation d'étalon de qualité au sein
the tool. Expendable Materials, such as pipe or drain cleaning tools, rods de la profession. Le matériel RIDGID bénéficie d'une garantie à
and cables, etc. are not covered by this warranty. Obviously, failures due vie contre les défauts de matériel et de main d'oeuvre. Les
pièces d'usure, telles que les fraises, câbles et tiges de curage,
to misuse, abuse, or normal wear and tear are not covered by this warran-
etc., ne sont pas couvertes par cette garantie. AUCUNE
ty. NO OTHER WARRANTY EXPRESS OR IMPLIED, APPLIES,
AUTRE GARANTIE EXPRESSE OU IMPLICITE, Y COMPRIS
INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR D'EVENTUELLES GARANTIES DE VALEUR MARCHANDE
PURPOSE. No employee, agent, dealer, or other person is authorized to OU D'APPLICABILITE PARTICULIERE, N'EST D'APPLICA-
alter this or make any other warranty on behalf of RIDGE TOOL COMPA- TION. Aucun employé, agent, distributeur ou autre personne
NY. To obtain the benefit of this warranty, deliver the complete product n'est autorisé à modifier ou à compléter cette garantie au nom
prepaid to RIDGE TOOL COMPANY or any RIDGID® AUTHORIZED SER- de RIDGE TOOL COMPANY. Pour bénéficier de cette
VICE CENTER. Pipe wrenches and other hand tools should be returned garantie, l'appareil complet doit être soit expédié à la RIDGE
to place of purchase. Warranted products will be repaired or replaced, at TOOL COMPANY en port payé, ou remis à un SERVICE D'EN-
RIDGE TOOL'S option, at no charge and returned via prepaid transporta- TRETIEN AGREE de RIDGID®. Les clés à griffe et autres outils
tion. This limited LIFETIME WARRANTY is the sole and exclusive warran- doivent être renvoyés à leur point d'achat. Les produits garantis
ty for RIDGID® products, and the remedy of repair or replacement is the seront soit réparés ou remplacés gratuitement, à la discrétion
sole and exclusive remedy for any nonconformity with this warranty. de RIDGID, puis réexpédiés en port payé. Cette GARANTIE A
RIDGE TOOL shall not be responsible for damages of any sort, including VIE limitée est la seule et unique garantie applicable aux pro-
incidental or consequential damages. duits RIDGID®, et la réparation ou le remplacement du produit
sont les seuls et uniques recours offerts au titre de cette
garantie. RIDGE TOOL ne saurait être tenu comme respons-
able pour dommages éventuels de quelque nature que se soit,
y compris les dommages directs ou consécutifs éventuels.

GARANTIA DE POR VIDA

El renombre de las herramientas RIDGID® es el resultado de
Ridge Tool Company una calidad consistente del producto y de años de excelencia
400 Clark Street en la mano de obra. Las verificaciones y los controles rig-
urosos, desde los materiales crudos hasta los productos embal-
Elyria, Ohio 44036-2023 ados, garantizan una confianza en el producto que es aceptada
como la norma de los oficios profesionales. Durante la vida de
la herramienta, las herramientas RIDGID están garantizadas de
estar libres de defectos de mano de obra o de material. Los
materiales substituibles, como por ejemplo las herramientas de
limpieza para tubos o desagües, así como las varillas y cables,
no están cubiertos por esta garantía. Obviamente, los fallos
debidos al uso indebido, al abuso, o al desgaste normal no
están cubiertos por esta garantía. NINGUNA OTRA
GARANTÍA, EXPRESA O IMPLÍCITA ES APLICABLE, INCLU-
SIVE DEL ASPECTO COMERCIABLE DEL PRODUCTO O DE
SU IDONEIDAD PARA UN PROPÓSITO EN PARTICULAR.
Ningún empleado, agente, distribuidor, ni cualquier otra per-
sona dispone de autorización para modificar lo presente ni
para ofrecer cualquier otra garantía en nombre de RIDGE
TOOL COMPANY. Para beneficiarse de esta garantía el pro-
ducto completo debe ser entregado con flete pagado a RIDGE
TOOL COMPANY, o a cualquier CENTRO AUTORIZADO DE
SERVICIO RIDGID®. Las llaves para tubos y otras herramientas
de mano deben ser devueltas al lugar de su compra. Los pro-
ductos garantizados serán reparados o recambiados, según cri-
terio de RIDGE TOOL, libre de gastos para Usted y serán
devueltos vía transporte pagado. Esta GARANTÍA LIMITADA
DE POR VIDA es la única garantía exclusiva para los productos
Ridge Tool Subsidiary RIDGID® y el recurso de la reparación y el recambio son los
Emerson Electric Co. recursos únicos y exclusivos en referencia con cualquier incon-
formidad relacionada con esta garantía. RIDGE TOOL no será
responsable de daños de ningún tipo, inclusive de los daños
incidentales o consecuentes.

Printed in U.S.A. 4/98 999-997-049.10