0% found this document useful (0 votes)

78 views129 pages

User'S Manual: Not Intended For Sale

This document is the user's manual for the NX-10 printer. It provides instructions on setting up the printer, using its controls and features, formatting text, printing graphics, and caring for the printer. The manual covers topics such as loading paper, selecting print modes, defining custom characters, using dot graphics commands, and troubleshooting issues. It contains appendices that list ASCII codes, character fonts, function codes, and other technical reference information for operating the printer.

Uploaded by

Venkata Sandeep Gopineedi

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

78 views129 pages

User'S Manual: Not Intended For Sale

Uploaded by

Venkata Sandeep Gopineedi

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 129

NX-10

USER’S MANUAL

NOT INTENDED FOR SALE

PN 80820128
Federal Communications Commission
Radio Frequency Interference
Statement
Thw rquipment generates and uses radio frequency energy and if not installed and used
properly. that is. in strl~“l accordance Lvith the manufacturer’s instructions, may cause in-
terference to radio and [etexxion reception. It has been type tested and found to comply
with the limits for a Ctavs B computing device in accordance wth the specifications in
Subpart J of Part 15 of FCC Rules, ivhich are designed to provide reasonable protection
against such inrerfcl-ence in a residential installation. Ho~vever. there is no guarantee
that interfrr-ence ~?ll not occur- in a particular installation. If this equipment does ~tuse
interference to radio or telex-ision reception. which can be determined by turning the
equipment off and on. the user is encouraged to try to correct the interference by one or
more of the folk)\\-ing measures:
l Reorient the receiving antenna
oRelocate the computer \vith respect to the receiver
l Slovv the computer away from the receiver
l Ptug the computer into a different outlet so that computer and receiver are on dif-
fercnt branch circuits.
If necessary. the user should consult the dealer or an experienced radioitete\,isiorl techni-
cian for additional suggestions. The user map find the following booklet. prepared h!
the Federal Communications Commission helpful: “Ho\r to Identify and Kesotve Radw
T\’ Interference Prohlrms. ” This hooklet is available from the I’.S. Government
PI-inting Office. LVashington. D.C.. 20402. Stock No. 001-000-00345-4.

For compliance with Federal Noise Interference Standard. this equipment requires a
shielded cable.

Self Declaration

Radio interferences regarding this equipment has heen eliminated according to Vfg
lO-l6/1984 announced hy the DBP.
DBP has been informed about the introduction of this special equipment and has been
conceded the right to esamiw the whole series.
It is upon the responsibility of thv user to assume that his own asscmhted system is in ac
cordance with the technical regulations under Vfg lOltiilYX4.
To observe FTZ-regulations it is necessary. to establish all connections io the printer
\vith shielded cable.

Trademark Acknowledgement
NX-10, grafstar: Star Micronics Co., Ltd.
r\pple, Apple II, ;2pple II - , Apple II e, Applesoft: Apple computer Inc
Commodore C-&l: Commodore Business Slachines. Inc.
Compaq: Compaq Computer Corporation
CI’IM: Digital Research
IBM Personal Computer, IHM LX: International Kusinehs Machines Corp.
Kaypro: Kaypro Corporation
Microsoft Rr\SIC: Microsoft Corporation
Osborne 1 : Osborne Compu~el- Corporation
TRS-80: Radio Shack. a division of Tandy Corporation

NOTICE
l A1l rights reserved. Reproduction of any part of this manual in any form what-
soever, without STAR’s express permission is forbidden.
l The contents of this manual are subject to change without notice.
l All efforts have been made to ensure the accuracy of the contents of this manual at
the time of going to press. However, should any errors be detected, STAR would
be greatly appreciate being informed of them.
l The above notwithstanding, STAR can assume no responsibility for any errors in
this manual.

Chapter 7 Dot Graphics 101

Comparing dot graphics with download
characters
Using the dot graphics commands
Specifying the number of columns of dots
Specifying the graphics data
Combining text and graphics
Printing a design or logo
Plotting with your printer
How the program works
High resolution graphics
Compatibility with existing software
More graphics programming tips
Redefining alternate graphics codes
g-pin graphics mode
Chapter 8 Caring for Your Printer 123
Cleaning the printer
Replacing the ribbon
Replacing the print head
Appendix A DIP Switch Settings 131
Switch functions
Appendix B ASCII Codes and Conversion 135
Chart
Appendix C Character Fonts 143
Roman characters
Standard characters (Set #l and Set #2)
Special characters (Set #2 only)
International characters
Italic characters
Standard characters (Set #l and Set #2)
Special characters (Set #2 only)
-
..”

Appendix D Function Codes 165

Commands to control print style
Font style controls
Font pitch controls
Special print modes
Controlling the vertical print position
Line feed and reverse line feed
Form feed and related commands
Top/bottom margins and vertical tabs
Controlling the horizontal print position
Download character commands
Dot graphics commands
Macro instruction commands
Other commands
Appendix E Command Summary in Numeric 209
Order
Appendix F Technical Specifications 213
Appendix G The Parallel Interface 217
Functions of the Connector Signals
Appendix H Connecting with Computer 221
Connecting with IBM-PC and COMPAQ
BASIC programming
Listing programs
Connecting with Apple Il computers
Applesoft BASIC
Listing programs
Connecting with TRS-80 computers
TRS-80 BASIC
Listing programs
Connecting with Kaypro, Osborne, and other
CP/M computers
Using MBASIC
Listing programs
CHAPTER 1

SETTING UP YOUR
PRINTER

Subjects we’ll cover in Chapter 1 include-

. Choosing a suitable place for your printer;
l Unpacking your new printer;

l Setting it up.

WHERE SHALL WE PUT IT?

Before you do anything else, give some thought to where

you’ll be using your printer. Obviously, it will be somewhere
near your computer. And both printer and computer will lead
longer, healthier lives if they like their surroundings. For in-
stance, we recommend.. .

, l Using the printer on a flat surface.

l Keeping it out of direct sunlight and away from heat-
producing units.
l Using it only in temperatures where you are comfortable.
l Avoiding areas with a lot of dust, grease, or humidity.
l Giving it “clean” electricity. Don’t connect it to the same
circuit used by large, noise-producing appliances (such as
refrigerators).
l The line voltage should be the same voltage that’s
specified on the identification plate - within 10% of the
recommended voltage.
2

WHAT HAVE WE HERE?

Now let’s take a look at what’s in the carton. Open it up and

check each item in the box against Figure l-l. There should be
four items.

.. -- -_ _
F‘igure l- 1. Check to make sure you have all four items: 1) printer,
2) paper guide, 3) ribbon cartridge, and 4) user’s manual.

Let’s move on the next step.

n Removing the printer cover

The cover is important for two reasons - it keeps dust and
dirt away from the printer’s delicate “innards,” and it quiets the
printer’s operation. Don’t take off the cover except when you
have to change the ribbon, or to make an adjustment.
lj
3

Removing the printer cover is easy. Lift up the back of the

cover to disengage the two tabs at the front and then lift it off
the rest of the way. To replace it, just slide the tabs in at the
front and lower it into place. Figure 1-2 shows the proper posi-
tion and movement for both removing and replacing the cover.
.

...

.gure 1-2. Remove the printer cover by lifting carefully.

.I, n Removing the packing tube

The printer is shipped with a protective spiral tube to keep
-. the print head from being damaged in transit. We have to
remove this tube. First, remove the printer cover. See the tube
L_ on the carriage rail (Figure l-3). Pull it off carefully.

-..
.
--
Figure 1-3. Remove the protective tube from the carriage rail.

Up to this point, we’ve been clearing the decks for action, so

to speak. Only one more thing left to do before we can start
printing - install the ribbon cartridge.

n Installing the ribbon cartridge

This printer uses a neat, easy-to-change ribbon cartridge so
you don’t have to spend a lot of time threading a ribbon. And get-
ting your hands all dirty to boot.
Telling you how to put in a ribbon is like explaining how to tie
your shoelaces - it takes a lot longer to tell than to do. You can
just follow the illustrations if you wish; they’ll tell you all you
really need to know.

Or, if you feel better following written instructions, read on.

1. Turn off the power and remove the printer cover.

2. Now slide the print head gently to the center of the
printer.
5

Warning: The print head gets hot during operation, so

let it cool off before you touch it.

/ Figure 1-4. Press the cartridge into place until the holdmg springs
snap into place.

3. Using the guide holders as a fulcrum with the ribbon fac-

ing away from you, as shown in Figure 1-4, lightly press
the cartridge down until the two holder springs snap shut
to hold the cartridge firmly in place.
4. Check that the cartridge fits so that the drive pins engage
the cartridge teeth.
5. Gently slide the print head carriage manually all the way
to your right or left until the ribbon automatically slips
down into its proper place between the print head and the
silver ribbon guide.
. 6. Put the printer cover back on and you’re finished. (A
special switch on the printer prevents the printer from
working when the cover is off.)
6

Print head

Figure 1-5. All you have to do is to slide the print head carriage
manually to your right or left, then the ribbon slips down by itself into
its proper position.
.,

CHAPTER 2

GETTING TO KNOW
YOUR PRINTER

Subjects we’ll cover in Chapter 2 include -

l Parts of the printer - what they’re for and how
to use them;
l Paper selection and loading;

l Adjustment;

l Connecting your printer to the computer;

l Extra functions with the control panel.

CONTROLS AND PARTS OF THE PRINTER

H Parts of the printer

First, we’ll go over the parts of the printer. You saw most of
these when you unpacked your printer. Now we’ll give you a
brief explanation of what they do. (For details on the initial set-
up of this printer, with all components in place, see Chapter 1.)

PRINTER COVER - This protects the ribbon and the print

head from dust and dirt, and cuts down the sound of the printer.
PAPER GUIDE - As you’ve guessed, this flat plastic
molding guides the paper during printing (it is raised for single
sheets and lies flat for sprocket-feed paper).
POWER CORD - This cord connects the printer to its power
source, usually a wall outlet. It’s located at the left rear of the
printer.
PRINT HEAD - This is the unit that does the actual printing.
Like the strike lever in a typewriter, tiny, stiff wires in the print
head hit the paper through a ribbon.
r
Tractor feed unit

’ I nterf

’ Power switch
\
Power cord

Figure 2- 1. Front and rear views of the printer

TRACTOR FEED UNIT - The drive gear and sprockets of

the tractor feed unit move sprocket-feed paper through the
printer.
I
.
9
_
PLATEN - This is the rubber cylinder that carries paper to
the print head.
INTERFACE CONNECTOR - On the back of the printer,
this connector is used to connect your computer to the printer.

n Controls and indicators

Now let’s take a tour around the controls, starting with the
control panel on the right. There are seven indicators and four
keys on the control panel.

I. I

. Figure 2-2. The control panel.

w. POWER INDICATOR - Glows red when the power is on or

blinks when the printer is out of paper or some other error
L-. occurs.
BOLD KEY and INDICATOR - Pressing this key selects
boldface printing.
DRAFT INDICATORS (80,96,136) - Glows green to in-
. .
dicate the number of characters per line when the printer is in
‘the draft mode (set by the Mode key or the software control).
w..
NLQ INDICATOR - Glows green when the printer is
printing in the Near Letter Quality (NLQ) mode (set by the
. . .
Mode key or the software control).
MODE KEY - Changes the print mode every time it is
pressed.
PAPER FEED KEY-Advances
LI

the paper one line at a time

when the On Line indicator is off. If you hold the key down,
you’ll get consecutive line feeds, one after the other. If you push
the On Line key while holding this key, you can advance the
paper to the top of the next page or a new form.
.
ON LINE KEY and INDICATOR - Glows green when the
printer can receive data from your computer (on line). When the
printer is off line, it sends a signal to the computer indicating
dI
that it cannot accept data. Pressing the On Line key switches
the printer on line and off line.
10

n Extra functions
There are eleven more functions that are not directly
specified on the control panel. You can use six of them by press-
ing a key (or keys) when you turnon the power; five others are
activated by pressing two control keys at once.
For details, please refer to the end of this chapter.

n Other controls
There are other controls, not connected to the control panel
board. Some of the more important ones are:

POWER SWITCH - The switch to turn the printer on is at

the back, on the left side.
PLATEN KNOB - This knob is at the middle of the right
side and lets you turn the platen by hand, just like a typewriter.
Caution: Turn this knob only with the Power switch off. Turn-
ing it with the power on could damage the platen drive
gears.
RELEASE LEVER - The release lever is on top of the
printer, near the left rear corner. You’ll be using it often - it
controls how strongly the paper is held against the platen. The
release lever has four positions: the top setting is used for inser-
ting paper, the next is for single sheets, the third is for sprocket-
feed paper, and the bottom one is used when adjusting the
pwfl.
PAPER BAIL - The bail is the movable bar that holds the
paper against the platen. Its position depends on the setting of -
the release lever.
DIP SWITCHES - These are a set of ten switches and a set _ -I
of six switches that are used in interfacing the printer to your
computer. There are also switches to set page length, character
style, perforation skipping, and selecting the international
character sets. See Appendix A for a complete list and explana-
tion.

SELECTING AND LOADING PAPER

Your printer can handle the two basic types of paper-single

sheets (stationery, envelopes, multipart business forms, etc.)
and continuous paper (fan-folded perforated paper).
This is a good place to tell you about the release lever, which
11

you’ll be using often. This lever controls the pressure of the

paper against the platen.
It has four settings:
g - The top setting is used when you want to load paper in the
printer.
c - The second setting is for normal single sheets.
fi - The third is for sprocket-feed paper.
4 - The bott om one is used when you want to release the
paper completely to adjust it.
The paper bail holds the paper against the platen according to
the setting of the release lever. The bail is opened when the
release lever is in the top position, closed when the lever is in
the second or third positions, and opened by the printer when
the lever is in the bottom position.

II -
Release lever

L---L
I

Figure 2-3.
continuous
. ’ Paper bail

Use friction feed for single sheets and tractor feed for
paper.

n Loading single sheets

Now, instead of feeding the paper in manually by turning the
platen knob, we’re going to use the release lever (the printer
must be turned on). Remember what we told you about this
lever? It allows you to advance the paper according to its posi-
tion.
19

OK? Let’s start.

1. Move the sprockets on the tractor feed unit all the way to
the ends.
2. Slide the sheet guide all the way to the right.
3. With the ribs of the paper guide toward you and the
sliding adjuster at the bottom left, insert the guide into
the slot at the back of the printer cover.

Sheet guide
/ Sprocket

‘igure 2-4. Raise the paper guide for loading single sheets.

4. Insert the guide stand in the notches provided for it and

use it to prop up the paper guide.
5. Position the adjuster at the triangle marked on the guide
for standard margins, or set it according to your re-
quirements.
6. Set the release lever for single sheets-the second posi-
tion from the top.
7. Align a sheet of paper on the guide along the adjuster.
8. Turn on the power switch. (The Power indicator will
blink because there is no paper.)
.,

L .. . . . . .. *.
Figure 2-5. l’rop up the paper guide by inserting me guise stana in
the notches provided for it.

‘igure 2-6. You can insert a sheet of paper by using the release
lever.
14

9. Now set the release lever to the auto-feed setting-the

top position. The printer will advance the paper
automatically.
10. When the paper stops, set the release lever for single
sheets again.

To align paper that is not in straight-

. Set the release lever to the adjustment setting.
l Straighten the paper and adjust it for the margins you
want.
l Move the release lever back to its original setting.

n Loading sprocket-feed paper

This is the familiar computer paper, with the holes along the
sides and perforations between the sheets. It is also called
sprocket, punched, fan-fold, or just plain “computer paper.” It
can be as narrow as 4”) and up to 10” wide.
Figure 2-7 shows the tractor unit. Please identify the parts of
the tractor.

1. Turn on the printer and set the release lever for sprocket-
feed paper.
2. If the paper guide is installed, remove it.
3. Place a stack of fan-fold paper behind the printer.
4:Open the sprocket covers, on the right and left sprocket
units, as shown in Figure 2-7.

Figure 2-7. Open the sprocket covers to expose me sproaet teem.

II
‘,,, ,’

5. Flip the clamp levers backward. This allows the two

sprocket units to move freely right and left so you can
align them with the holes in the paper.
6. Feed the end of the paper into the slot next to the platen
cover plate.
7. Fit the holes in the paper over the sprocket pins so the
paper is even, and clamp the sprocket units in place.
. 8. Check that the paper is still positioned correctly, and
close the sprocket covers (Figure 2-8).
9. The Power indicator should be blinking. Turn the platen
knob to feed the paper until the indicator stops blinking.
10. Now turn the platen knob the other way just a bit, until
the indicator starts blinking again.
11. Set the release lever to the auto-feed setting. The printer
will advance the paper automatically.
12. When the paper stops, set the release lever for sprocket-
feed paper again.
13. Finally, install the paper guide on the printer (Figure
2-8). Now you’re ready to roll!

“igure 2-8. Ready to run with sprocket-feed paper.

ADJUSTING THE PRINT HEAD

The distance between the print head and the platen must-be
adjusted to accommodate papers of different thicknesses. To
make this adjustment, move the adjustment lever, which is
under the printer cover and immediately in front of the release
lever (Figure 2-9). Pulling the adjustment lever towards you will
widen the gap; pushing it away from you will narrow the gap.

Figure 2-9. The adjustment lever allows for different thicknesses -

of paper.

There are four positions; you can feel the lever clicking into - --
the various notches. The first step (illustrated) is the one most
commonly used for single sheets of paper.
You shouldn’t have any trouble finding the right gap setting
for your paper. If necessary, experiment; you’ll soon find the
best position for the paper you’re using.

CONNECTING THE PRINTER

Now that you have assembled your printer, it’s time to use it
for what you bought it for - print information from your com-
puter. But first you have to connect it to your computer. Please
follow the instructions in the order listed below.
17

1. Make sure both your computer and printer are turned

off.
2. Connect one end of the interface cable to the connector
socket at the right rear of the printer as shown in Figure
2-10.
3. Connect the other end of the cable to your computer as
described in the computer manual.

.
/-
Figure 2-10. This is how you connect the cable.

‘EXTRA FUNCTIONS WITH THE CONTROL PANEL

There are many functions that are not directly specified on

the control panel. In this section, we’ll show you these extra
functions.

Italic mode _I

L Panel mode
Italic and Panel mode

Figure 2-11. Extra functions while turning on the printer.

n Self-tests
Your printer has two built-in programs that print out sample
lines of letters, numbers, and other characters-to show you
that everything’s in good working order. Self-test 1 is the long
version, and self-test 2 is the short one. You can use either one
to show the characters available in the printer, to check the in-
stallation of the ribbon and paper, and to check the adjustment
of the head-to-platen gap.
Best of all, you don’t have to wait another minute-you can
print the self-test without hooking up the printer to your com-
puter! It’s as simple as 1, 2, 3. . .

1. Plug in the printer (don’t turn it on yet).

2. Insert a sheet of paper (or sprocket paper, either one).
3. While holding down one of the following keys, turn on
the power switch:

Paper Feed key-Self-test 1 (long)

On Line key-Self-test 2 (short)

'igure 2-12. The self-tests show you what the printer can print.

Were you surprised? It’s fast, isn’t it? About 120 characters a
second, to be exact.
When you want to terminate the self-test function, turn off the
power switch.
n Hex dump
Can you guess what a “hex dump” is? No, it’s not where
witches throw away useless spells. A hex dump is an advanced
ability of your printer that you can use, in certain cases, to find a
problem with your system. Fortunately, such problems rarely
arise but the hex dump is available if one does. We’ll go over
hex dump in Chapter 4. Right now, we’ll just tell you how to
make a hex dump:

1. Plug in the printer (don’t turn it on yet).

2. Insert a sheet of paper, as you did for the self-tests.
3. While holding down both the Paper Feed and Mode keys,
turn on the power switch.

W Panel mode
As you’ll learn in Chapter 5, this printer has many software
controls. But if you want to print in one mode, ignoring the con-
trol codes, the “Panel” mode takes effect for you. To set the
“Panel” mode, follow the procedures:

1. Plug in the printer (don’t turn it on yet).

2. While holding down the Mode key, turn on the power
switch.

< Notice that this mode stays on until you turn off the printer.

n Italic mode
Sometimes, you may want to print with italic characters with
Draft mode as the power-on default. You can set the Italic mode
with the following procedures:

1. Plug in the printer (don’t turn it on yet).

2. While holding the Bold key, turn on the power switch.

This mode stays on until you send the cancel command to

your printer. This mode re-activates when you send the reset
command to your printer.

n Italic and Panel mode

You can combine with the “Panel” mode and the “Italic”
mode at a time. To set these modes at a time follow the pro-
cedures below:
1. Plug in the printer (don’t turn it on yet).
2. While holding both the Mode and Bold keys, turn on the
power switch.

Right margin set

**: Hold down L- Left margin set

~---____
Figure 2-13. You can set many functions by the combinations of
the control panel keys while in the Off Line mode.

n Setting print start position

When you want to align the print start position, you can set it
by the micro-feed operation with the control panel, instead of
turning the platen knob manually.
1:Set the Off Line mode by pressing the On Line key.
2. While holding down the On Line key, press one of the
following keys.
Paper Feed key - Forward micro-feed
-
Mode key - Reverse micro-feed 1
3. When you can set the print start position, release the
Paper Feed key or the Mode key first, then release the
On Line key.

n Setting the left and right margins

As you’ll learn in Chapter 4, you can set the left and right
margins with control codes. In addition, you can set them by the
following procedures.

1. Set the Off Line mode by pressing the On Line key.

2. While holding the Bold key, press one of the following
keys.
Mode key - Left margin set
Paper Feed key - Right margin set
3. While holding the two keys, the print head moves across
the page step-by-step.
4. When the print head goes to the position where you want
to set margin, release the two keys. So the printer
acknowledges the margin with the sound of beep.
22

MEMO
CHAPTER 3

BASIC PRINTING

Subjects we’ll cover in Chapter 3 include-

* Listing BASIC programs on the printer;
l How a program prints things;

l Control codes, escape codes, and command syn-

tax;
l Near letter quality (NLQ) characters;

l Fixed and proportional character spacing;

l Special printing -

Printing in italics,
Underlining,
Superscripts and subscripts,
Boldface and emphasized text,
Mixing print modes.

, To show you how to control your printer from a program, we

choose BASIC because it is easy to learn and easy to use. Also,
more personal computer users program in BASIC than in any
other language.
The rest of this manual will show you a little BASIC - just
enough for.you to use your printer. We’re not going to try to
make you an expert programmer, though, only get you started.
There are many excellent books that will teach you BASIC, so if
you discover that you like to program you should have no
trouble learning more about it.

SOME BASICS OF BASIC

H A new language!
Many people who meet BASIC for the first time are in-
timidated. Some are put off by the idea of learning any new
. . .,I

; 24

language, perhaps recalling the rigors of high-school Latin.

Others are unnerved by anything having to do with computers.
Well don’t be! In the first place, BASIC may well be the
easiest language you could learn: it has a vary limited
vocabulary, a simple but precise grammar, and its dialects -
unlike those of English - usually different from each other only
in minor detail. Without programming, a computer is a useless
collection of chips and wire - why should we think of it as
something special? Anyway, computers are here to stay - let’s
accept them with good grace.

n First steps
The first things that a beginner learns to do are to list a pro-
gram and to print a character string. Certainly these are the
easiest operations one can do, but even they may depend on
what computer you have. In Microsoft BASIC, we can list all
the steps in a program by entering LIST. This lists them on the
CRT screen; if we want to print them on a printer, we prefix the
command with an L (enter LLIST).
The Microsoft BASIC command for outputting information is
PRINT. Like the LIST command, this displays the information
on the CRT screen so we have to add an L (+ LPRINT) if we
want to use the printer. Just put whatever you want to print
between quotes and after LPRINT (anything enclosed in quotes
is called a character string). For example, we would use
LPRINT “Hello!” to output “Hello!” to the printer. We’ll see
later how to LPRINT things other than character strings.
We started with Microsoft BASIC because it is the most wide-
ly used version of BASIC around. The programs in this manual
are written in Microsoft BASIC so they should run on most com-
puters. But if strange things happen when you try to run a pro-
gram, check the BASIC manual that came with your computer.
Let’s talk about Apple II computers for a minute. These
enormously popular computers use their own brand of BASIC.
To use an Apple II, enter the following -

PR#l -
PR#l
LIST PRINT "Hello! It
PR#O PR#O -

The PR#l tells the Apple to send everything to the printer,

the LIST or PRINT command sends it, and the PR#O returns
25

output to the screen.

Other computers, notably the Commodore C-64, require you
to open the printer as a numbered device then to direct output to
that device. For example, you might type the following to print
“Hello!” or to list a program in the C-64’s memory.

OPEN4,4 OPEN4,4
CMD4 CMD4
LIST PRINT "Hello! 'I
CLOSE 4 CLOSE4

Here, the first line says that the printer is device number 4,
the second directs output to it, the third does the printing, and
the last line closes down device number 4.
Appendix H gives more information about listing programs on
the various computers. Find the part that applies to your com-
puter and try it.
Now that we know how to address the printer, let’s try listing
a BASIC program. Load a program into memory ready to pro-
gram printer operation - just as soon as we learn a little bit
about the ASCII codes.

W ASCII codes and the CHR$ function

You talk to your computer in BASIC, but your computer and
your printer talk to each other in what are known as ASCII
codes. In the ASCII code, each number from 0 to 255 has a par-
ticular meaning - 36, for example, makes the printer print a
dollar sign. Some numbers cause the printer to do other things,
too. For instance, sending a 7 sounds the printer’s bell.
Taken together, these numbers and their meanings make up
the ASCII code (pronounced ask-key), which stands for the
American Standard Code for Information Interchange. There are
ASCII codes for all the letters of the alphabet (upper case and
lower case), 0 to 9, most punctuation marks, and some (but not
all) of the functions of the printer.
There are a number of different ways to represent an ASCII
code, depending on how you are using it. For example, the
ASCII codes for the letter “A” are 65 (decimal) or &H41 (hex-
adecimal). Or you can just call it “A”. Appendix B shows all of
the ASCII codes.
BASIC uses the CHR$ function to represent ASCII
characters and many functions. To print the letter “A” we
would enter LPRINT CHR$(65). To make the printer’s bell
sound, we would LPRINT CHR$(7). In general, we print a
character by entering LPRINT CHR$(ASCII code) to the
printer.
We can also use hex ASCII codes. Although we use only
decimal ASCII codes in this manual, you should understand at
least what a hex code is. “Hex” is short for hexadecimal and
refers to a base-16 number (the numbers we use in everyday life
are base 10). Since the hex system needs 16 digits, it uses the
numerals 0 through 9 and also the letters A through F. You can
always tell that a number is in hexadecimal by the “&H” im-
mediately preceding it. The ASCII code for the letter “A” (65 in
decimal) is &H41 in hex.

n Control codes
ASCII codes with values of 32 or less do not have their own
keys. These codes control many of the printer’s functions, so we
call them control codes. To enter a control code from the
keyboard, we have to press two keys at the same time - the
“control” key and one other. The other key determines what
code is sent - pressing the control (CTRL) key and A sends
ASCII code 1, CTRL B sends ASCII code 2, and so on.
Your printer has a lot of control codes to let you do some real-
ly nifty things. Let’s try one that we’ve mentioned several times
already:

10 1 Demo of ASCII code

20 LPRINT CHR$(7)
30 END
RUN

That’s the printer’s bell (we call it that even though it sounds
like a buzzer). We’ll learn more about it in later (we just wanted
to show you a control code that would get your attention right
away).
There are four common ways of referring to a control code:
the name of the code or its abbreviation, the decimal ASCII
value, the hexadecimal ASCII value, and the “CTRL-” value.
For example, the ASCII code that causes the printer to advance
the paper one line is decimal 10. This code may be referred to
by any of the following.
27

line feed -the name of the code

UJ’) -its abbreviation
ASCII 10 -its decimal value
ASCII &HOA -its hexadecimal value (the &H signifies
hex)
CHR$(lO) -the way it’s used in BASIC
CTRL- J -the way you send it from a keyboard

Of course, most of the time we don’t need to bother with

these. Our computers are smart enough to know that when we
press the “A” key we want to print the letter “A” - they take
care of all the intermediate steps.
Appendix B is a table that shows the various names for each
code so you can convert back and forth. The microcomputer
world is not very consistent in describing ASCII codes, so it’s
important that you have a basic knowledge of them.

n The escape codes

Back when the ASCII system was set up, computer equip-
ment was relatively simple and thirty-three control codes were
considered sufficient at the time. The American Standards
people realized that, eventually, more control codes would be
needed so they included the escape (ESC) code to allow almost
any number of additional codes to be defined when they became
necessary.
ESC allows us to “escape” from the ordinary set of control
codes so we can specify additional functions and other informa-
tion needed for a printer function. In this manual, we’ll write the
ESC code inside broken brackets, like this - (ESC).
(ESC) - ,decimal 27 - is always followed by at least one
other number; it is never used alone. The whole series of related
numbers is called an escape sequence.

W A note on command syntax

Because the readers of this manual will be running such a
wide variety of applications on so many different computers, we
just can’t show the exact way of sending codes to the printer for
each one of them. Instead, as we introduce you to each new com-
mand, we will show the commands as in this example:

(ESC) “W” 1
28

This command that turns on expanded printing. (ESC), as we

mentioned earlier, is the escape code (which is ASCII code 27).
A letter or number in quotes (such as the “W” above) means that
the character should be sent to the printer (without the quotes).
In our example, you should send a capital W following the
escape code. In BASIC, you could do this in a couple of ways: by
sending the character itself (e,g, LPRINT “W”;), or by using the
CHR$ function to send the ASCII code for the character (e.g.
LPRINT CHR$(87);).
Many of printer commands end with a 1 or 0. When shown as
in the above example (i.e. no quotes and no “CHR$“), you can
use either ASCII code 1 (i.e. CHR$(l)) or the character “1”
(which is ASCII code 49). The same idea applies to commands
ending with 0.
So for out example above, any of these BASIC statements will
have the same result:

LPRINT CHR$(27>;"W";CHR$(l>
LPl-lINTCHR$(27);"W';CHR$(49)
LPRINT CHR$(27);"Wl"

Even though, there are many commands that require the use
of ASCII code 0; the character “0” (ASCII code 48) cannot be
substituted. In these cases, instead of an unadorned 0 we will
show ‘CHR$(O) each time these commands are referenced.
That’s it for the basics. You are now ready to learn how to use
the many features of your printer.

SOME SPECIAL HINDS OF TEXT

If you looked carefully at your printer’s self test, you noticed

that it can print in italics. But there’s more! Your printer can
underline characters, print superscripts and subscripts, and
perhaps most exciting, print near letter quality characters.

n Near Letter Quality characters

This printer’s Near Letter Quality (sometimes abbreviated as
NLQ) character set is ideal for correspondence and other impor-
tant printing, for it takes a keen eye to detect that it is from a
dot matrix printer. Normally, your printer prints draft quality
characters. This is adequate for most work and it prints fastest.
29

But for the final printout, try NLQ. The program below shows
how.

10 1 Demo of NLQ character set

20 LPRINT CHR$(27);"xl";
30 LPRINT "This line shows NEAR LETTER QUALITY!
40 LPRINT CHR$(27);"xO";
50 LPRINT "This line shows standard print."

In this program, line 20 selects NLQ characters with (ESC)

“~“1 command. Line 30 prints a sample before line 40 switches
printer back to draft printing with an (ESC) “~“0. When you
run the program you should get this:

This line shows NEAR LETTER QUALITY!

-)_1-7j. ::i :I.i II e 55II C)w E:i E;t,~ilCl~~r-d pr i nt n

Table 3-1
Near letter quality commands
Function Control code
Near letter quality ON (ESC) “x” 1
’ Near letter quality OFF (ESC) “~“0

n Italic printing
Italic letters are letters that are slanted to the right. Your
printer can print all of its letters except NLQ characters in italic
as well as the roman (standard) letters you are accustomed to.
Italics can be used to give extra emphasis to certain words. The
command codes to turn italic on and off are shown in Table 3-2.

Table 3-2
Italic commands
.
Function Control code
Italic ON (ESC) “4”
Italic OFF (ESC) “5”

Use this program to see italic characters:

f Demo of italic and roman
:; LPRINT CHR$(27)*"4"*
30 LPRINT "This li;e ii in ITALIC characters."
40 LPRINT CHR$( 27);"5y
50 LPRINT "This line is in ROMAN characters."

Here is what you should get:

In this program, line 20 turns italic on with (ESC) “4”, and

line 40 turns italic off with (ESC) “5”.

W Underlining
Not only can your printer print all styles of printing in both
roman and italic, but it can underline them too. The control
codes are shown in Table 3-3.

Table 3-3
Underline commands
Function Control code
Underline ON (ESC) “-“l
Underline OFF (ESC) “-“0

Again, that’s simple. Let’s try it with this program:

' Demo of underlining

:; LPRINT CHR$(27)*"-1".
30 LPRINT "This ph;ase is UNDERLINED;";
40 LPRINT CHR$(27);"-0";
50 LP-RINT Itthis is not."

It should come out like this:

This phrase -I& UNDERLINED; this is not.

In this program underline is turned on in line 20 with (ESC)

“
-“l, and then off in line 40 with (ESC) “-“O. There’s a new
little wrinkle in this program, though. The semicolons at the
end of the first three lines told BASIC that those lines were to
be continued. Therefore, BASIC didn’t send a carriage return
and line feed at the end of those lines. We just did this to il-
lustrate that all these control codes can be used in the middle of
a line. It’s easy to underline or italicize only part of a line.

n Superscripts and subscripts

Your printer can print in two different heights of characters.
The smaller characters are called superscripts and subscripts and
are half the height of normal characters. Superscripts print even
with the tops of regular printing while subscripts print even with
the bottom of regular printing. They are frequently used to
reference footnotes, and in mathematical formulas.
Table 3-4 has the codes for using superscripts and subscripts.

Table 3-4
Superscripts and subscripts commands
Function Control code
Superscript ON (ESC>“S”O
Subscript ON (ESC)“? 1
Super and subscript OFF (ESC)“T”

Try this program to see them work:

10 1 Demo of superscripts and subscripts

20 LPRINT "Look! ";,
30 LPRINT CliR$(27);"SO";
40 LPRINT "SUPERSCRIPTS ";
50 LPRINT CHR$(27);"T";
60 LPRINT "& ";
70 LPRINT CHR$(27);"Sl";
80 LPRINT "SUBSCRIPTS ";
90 LPRINT CHR$(27);"T";
100 LPRINT "on one line."

I i ne .
32

Here line 30 turns on superscripts with (ESC) “SO. It’s turn-

ed off in line 50 with (ESC) “T”. Then between printing text,
subscripts are turned on in line 70 with (ESC) “S’l, and finally
off in line 90. Again, everything prints on one line because of the
semicolons.

CHANGING THE PRINT PITCH

In “printer talk,” the number of characters that can be printed

in one inch is called the print pitch or character pitch. Normally,
your printer is set for 10 characters per inch, which is called pica
(and is the same as the pica pitch on some typewriters). This
works out to 80 characters per line.
You can also print 12 characters per inch (elite pitch). This
gives you 96 characters per line.
You can set these pitches by using the Mode key on the con-
trol panel manually, or by software as shown in the table below.

Table 3-5
Print pitch commands
Pitch Characters/inch Control code
Pica 10 (ESC) “P”
Elite 12 (ESC) “M”

Try this program to see how these two pitches work. Be sure
to set the printer to draft mode.

10 ' Demo of pica and elite pitches

20 LPRINT CHR$(27);"M";
30 LPRINT "This line is ELITE pitch."
40 LPRINT CHR$(27);"P";
50 LPRINT "This line is PICA pitch (normal)."

When you run this program you should get this:

This line is ELITE pitch.

This line is F’ICC’r pikC:h (nor-mal).
33

Line 20 turns on elite pitch with (ESC) “M”. Line 30 prints a

line at 12 characters per inch. The (ESC) “P” in line 40 resets
the printer to pica pitch and line 50 prints a line in pica pitch.

W Expanded print
Each of the print pitches can be enlarged to twice its normal
width. This is called expanded print. Try this program to see
how it works:

10 ’ Demo of expanded print

20 LPRINT "Demonstration of 'I;
30 LPRINT CHR$(14);
40 LPRINT "EXPANDED";
50 LPRINT CHR$(20);
60 LPRINT " printing."
70 LPRINT "Notice that I';
80 LPRINT CHR$(14);
90 LPRINT "EXPANDED mode"
100 LPRINT "automatically turns off at the end
of a line."

Expanded print set with CHR$(14) is automatically cancelled

at the end of the line. This is convenient in many applications,
such as for one line titles. Note that you didn’t need to put an
(ESC) in front of the CHR$(14), although (ESC) CHR$(14)
works just the same.
You can also cancel one line expanded print before a carriage
return with CHR$(20), as done in line 50.
Sometimes you may wish to stay in expanded print for more
than one line. Change your program to this:

10 ' Demo of permanent expanded mode

20 LPRINT CHR$(27);"Wl";
30 LPRINT "Permanent expanded"
40 LPRINT "mode stays on until"
50 LPRINT "is is ";
60 LPRINT CHR$(27);"WO";
70 LPRINT "turned off."
34

Now the results look like this:

When you turn on expanded print with (ESC) “W”l it stays

on until you turn it off with (ESC) “W”0.

Table 3-6
Expanded print commands

n Condensed print
Each of the print pitches also can be condensed to its normal
width. This is called condensed print. Try this program to see
how it works:

10 f Demo of condensed print

20 LPRINT "Demonstration of ";
30 LPRINT CHR$(15);
40 LPRINT "CONDENSED";
50 LPRINT CHR$(18);
60 LPRINT Ifprinting."

Ihwmstt-at:i cm of CONDENSED pr-inkirrq.

. Condensed print set with CHR$(15) stays on until you turn it

off with CHR$(18). Note that you don’t need to put an (ESC) in
front of the CHR$(15), although (ESC) CHR$(15) works just
the same.
Table 3-7
Condensed print commands
Function Control code
Condensed ON CHR$(15) 01 (ESC) CHR$(15)
Condensed OFF CHR$(18)

By combining expanded print and condensed print with the

two pitches, this printer has eight different character widths
available.
Enter this program to see how the print pitches, expanded
print and condensed print can be combined:

' Demo of various print pitches

LPRINT CHR$(15);
LPRINT CHR$( 27);wy
LPRINT "This line is CONDENSED ELITE pitch."
LPRINT CHR$(27);"P";
LPRINT "This line is CONDENSED PICA pitch."
LPRINT CHR$(18);
LPRINT CHR$(27);"M";
LPRINT IfThis line is NORMAL ELITS; pitch."
100 LPRINT CHR$(27);"P";
110 LPRINT "This line is NORMAL PICA pitch."
120 LPRINT CHR$(27);"Wl";
130 LPRINT CHR$(lS);
140 LPRINT CHR$(27);"M";
150 LPRINT "This line is EXPANDED CONDENSED
ELITES."
160 LPRINT
170 LPRIN,T "This line is EXPANDED CONDENSED
PICA."
180 LPRINT CHR$(18);
190 LPRINT CHR$(27);"M";
200 LPRINT "This is EXPANDED ELITE."
210 LPRINT CHRS(27);"P";
220 LPRINT "This is EXPANDED PICA."
230 LPRINT CHR$(27) ;"WO"
240 END

Here’s what you should get from this program:

This line is CONDENSED ELITE pitch,
This line is CONDENSED PICA pitch.
This line is NORMRL ELITE pitch.
l-l-1 :i, vii :I. :i n e :i, 5; 111 IX? Pi u I,,., P 1: c:: (4 fl:, i t c3 t-l n
This line is EXPANDED CONDENSED ELITE.
This line is EXPANDED CONDENSED PICA.
l-h i .!sii?z EXF'ANDED ELI-i-E,
'-'[""
#--r
-j.
K;. ji-cc;;;Ef::
:,I;:
g.3&'::,
11"*,[
:J-J,
E; :/j-J1':"
J::
#-:y;
$-II
_

n Proportional printing
Have you ever noticed in books and magazines? Doesn’t it
look nice? The main reason is that each character is given an
amount of space proportional to its actual width. A typewriter
(and most printer), on the other hand, give every character the
same amount of space, no matter how wide it is. (Pica pitch, for
example, gives a “w” and an “i” l/10 of an inch each. Look these
letters closely and you’ll see that a “w” is two or three times as
wide as an “i”.)
Well, you too enjoy professional-looking proportional print-
ing. You can turn proportional printing on and off with the
following command.

Table 3-8
Proportional commands
-
Function Control code
Proportional ON (ESC)“p”l
Proportional OFF -
(ESC)“p”O

Try this program to see how the proportional spacing works.

10 ) Demo of proportional printing

20 LPRINT CHR$(~~);"M~;
30 LPRINT "This line is NORMAL ELITE printing."
4-O LPRINT CHR$(27);"pl";
50 LPRINT "This line is PROPORTIONAL ELITE."
60 LPRINT CHR$(27);"P";
70 LPRINT "This line is PROPORTIONAL PICA."
80 LPRINT CHR$(~~);~~~O~Q
90 LPRINT "This line is NORMAL PICA printing."
100 END
When you run this program you should get this:

This line is NORMAL ELITE printing.

This line is F’ROF’ORTIONAL ELITE.
“r1.7j.:~ :/.j.I-\e j.!ii; r~~I::;(:)~::~(::)~~1-~Ol\lnj...
p:I:C::A.
T l-1i 5; 1. :i.r1e i 5 NC:)R PICiL.. F’ I: CA 1:)r i n .t i ri g y

Line 20 selects the elite pitch and line 40 turns on the propor-
tional printing with (ESC)“p”l. Line 50 prints a line with pro-
portional elite pitch. Then, line 60 selects the pica pitch, so that
line 70 prints a line with proportional pica pitch. Finally, line 80
resets the proportional printing and line 90 prints a line in nor-
mal pica pitch.

NOTE: When you change the print pitch by the MODE key on
the control panel, this proportional spacing should be
automatically cancelled.

-.
MAKING WORDS STAND OUT

Your printer has very good print density when it’s just print-
ing regularly. But sometimes you may want something to stand
<out from the rest of the page. This printer provides two ways to
do this: boldface and emphasized print. Both of these go over
the characters twice, but they use slightly different methods to
darken the characters. Let’s try them and see what the dif-
ference is.
The following table shows the control codes for getting into
and out of boldface and emphasized modes.

Table 3-9
Print emphasis commands
-

Try them now with this little program:

f boldface and emphasized

2': ~PEE EHR$(~~) ;"G";
30 LPRINT "This iine is BOLDFACE printing."
40 LPRINT CHR$(27);"E";
50 LPRINT "This line is BOLDFACE and
EMPHASIZED."
60 LPRINT CHR$(27);"H";
70 LPRINT "This line is EMPHASIZED printing.'*
-
80 LPRINT CHR$(~~);"F";
90 LPRINT "This line is normal printing."
100 END

Run this program. The results will look like this:

This line is BCLUFUCE printing.

This line is BOLDFACE and EMPHASIZED.
This line is EMPHASIZED printing.
‘I-t.1
:i.5 :I,:i.n e j, 5; f-1I::)
r”ma :I. p r :i_n t. j. n (3 .

Line 20 turns on boldface with (ESC)“G” and line 30 prints a

line of text. In line 40 ‘emphasized is turned on with (ESC)“E”.
Line 50 prints a line of text in boldface and emphasized. Line 60
then turns boldface off with (ESC)“H” so that line 70 can print
in emphasized only. Finally, line 80 turns emphasized off, so
your printer is set for normal printing.
Look closely at the different lines of printing. In the line of
boldface printing each character has been printed twice, and
they are moved down just slightly the second time they are
printed. In emphasized printing, they are moved slightly to the
right the second time your printer prints. The last line combined
both of these so that each character was printed 4 times. Now
that’s pretty nice printing, isn’t it?

MIXING PRINT MODES

We have learned how to use the various print modes in-

dividually and together. Now we’ll see how to combine them
39

more efficiently.
You have at your disposal a unique command that lets you
choose any valid combination of print modes and pitch. This is
the Master Print mode command. It looks like this:

(ESC) “!” n

Here, the value of n defines the print style to be selected. The

value of n can range from 0 to 255, which is the range of values
that can be stored in one eight-bit byte. If you look at each bit in
this byte, you’ll find that each one represents a printing style
variation. Adding the binary values of the selected bits gives the
value of n for a particular combination of print styles.
Table 3-10 shows the decimal values of the bits in the Master
Print byte. To calculate the value n for a particular combination
of printing styles, just add the values of the features that you
want to combine.

Table 3-10
Values of mixing print styles for Master Print
1 Bit 1 Print stvle-
Decimal value 1

1 Elite print 1
2 Proportional print 2
3 Condensed mint 4
14 1 Emphasized print I 8 I
5 Boldface print 16
6 Expanded print 32
7 (Not used)
18 I‘ Underline ’ 128 1

For example, if you want to select elite expanded boldface

print, you would calculate the value of n like this:
Elite 1
Boldface 16
Expanded 32
n= 49

The command would look like this:

CHR$(27);“!“;CHR$(49)
To better understand the way the print modes work, consider
that each mode except pica (pica is the default) has a separate
switch that can turned on and off via software. Once the switch
is on, it stays on until turned off. When two modes that conflict
are turned on at the same time, the printer must choose which
one to use.
For example, suppose you turn on both Elite and Emphasized
modes. Since these cannot combine the printer must make a
choice; in this case, the printer chooses Elite.

Summary notes
1) Pica is the default pitch and is active when Elite is turned
off.
2) When two modes conflict, the one of lesser priority is
cancelled. For example, Condensed and Emphasized can
not be printed at the same time, printing is Emphasized.
3) Elite cancels Emphasized.
4) Underline, and Expanded modes combine with any print
modes.
5) Emphasized will not mix with Elite or Condensed.
CHAPTER 4

FORMATTING TEXT

Subjects we’ll cover in Chapter 4 include-

* The carriage return and line feed;
l The amount of space between lines;

l Moving to the next page;

l The number of lines on a printed page;

l Horizontal and vertical tabs;

l Setting margins- left, right, top and bottom;

l Centering and aligning.

Chapter 3 showed us all the basic techniques of using the

printer. Now we’re ready for the more advanced ones. We’ll con-
centrate on changing the appearance of the page to suit our
needs.

ilNES AND LINE SPACING

n Starting a new line

Up until now the only time we have thought about printing on
a new line is when we didn’t want it to happen. We learned that
putting a semicolon (;) at the end of a BASIC line will not end the
line of printing. So somehow, the computer telling the printer
when to end one line and start another.
There are two codes that are used to end one line and start
another. They are carriage return (CHR$(13)) and line feed
(CHR$(lO)). Like the escape code, they have been given ab-
breviations which you’ll find many texts (including this one):
<CR > and < LF > . The codes are simple, but their action is a
little confusing (especially with BASIC). Carriage return is the
easiest. Each time that the printer receives a CHR$(13) it
returns the print head to the left margin. It does not advance the
paper (if DIP switch 1-8 is on; see below).
42

Line feed is more complicated. Each time the printer receives

a CHR$(lO) it both advances the paper one line and returns the
print head to the left margin, ready to start a new line.
Now to add a little confusion-most (but not all) versions of
BASIC add a line feed (CHR$(lO)) to every carriage return
(CHR$(13)) that they send. If your version of BASIC doesn’t do
this, then you should turn DIP switch l-8 off so that your printer
will add the line feed for you. When you have DIP switch l-8 off
the printer will do the same thing when it receives a carriage
return as it does when it receives a line feed.
If you find that your printer double spa-es when it should
single space, then you probably need to turn DIP switch l-8 on.

n Reverse line feeds

Your printer has a unique capability: it can move the paper up
or down! Its unique tractor design allows the paper to be fed in
either direction without jamming. This allows you to move
around the page at will. You can use this feature to print several
columns of text side by side, or print a graph and then move
back up and insert descriptive legends. As you experiment
you’re bound to come up with more uses!
The simplest form of reverse paper feeding is a reverse line
feed. The code is (ESC)( LF), which causes the paper to move
down (in effect, moving the printing up) one line. A “line” used
in a reverse line feed is the same size as a line in a regular line
feed (this is normally l/6 inch). When you change the line spac-
ing (which you’ll read about next), you change it for both for-
ward and reverse line feeds.
Table 4-1
Line feed commands
Function Control code
Return print head to left margin CHR$(13)
Advance paper one line CHR$(lO)
Reverse paper one line (ESC)CHR$( 10)

n Changing the line spacing

When you turn your printer on the line spacing is set to 6 lines
per inch. This is fine for most printing applications, but
sometimes you may want something different. Your printer
makes it easy to set the line spacing to whatever you want.
Try this program to see how easy it is to change the line spac-
ing:
43

NEW
10 ( Demo of line spacing
20 FOR I=1 TO 25
IF 1=13 THEN 60
2 LPRINT CHR$(27);"A";CHR$(I);
LPRINT "THIS LINE SPACING IS SET TO";1
2: NEXT I
70 LPRINT "LINE SPACING IS SET TO 1/6 INCH
(NORMAL) .I!
80 LPRINT CHR$(27);"2"
90 END

This is what you will get:

! ‘f
.J!!
,’ :
I .!i
.-
..,.II \ IIn
IIMF \ .:L
L I NE
I- I lIEi: SfYl” 1-C:) :LiI
I- :I:NE S Et::
“I- ‘Tel 1I
l-l-l I s I.._I tw SF AC 1:NC< I 5 SET 1-a 112
T 1-lI: S I_ :I:i’.lE SI:-’A[:: :CN[17 :I:S S Et:T ‘1”
cl 1.4.
T t.41:S I....1:NE: SI”‘A!I I NG :I:s SE:T 1-o 1.5
T t-1I s I- :I:IIE 6~’ A c :I:la(~7 :I:s I-;if:.T T [:I 1 6
1:I\1E..: SF-’G C:1:l’\lG :I.SZ cz;1x:-r -r f-1 3,7
T ti :CS I__.
Line 40 changes the line spacing. The command (ESC)“A”
CHR$(n) changes the line spacing to n/72 of an inch. The loop
that is started in line 20 increases the value of n (the variable I in
this program) each time it is executed. So the line spacing in-
creases as the program continues. Line 30 just shortcuts the
loop when I= 13, since BASIC won’t let us send CHR$(13)
without adding an unwanted CHR$(lO) to it. Finally, the (ESC)
“2” in line 80 resets the line spacing to 6 lines per inch. This is a
shortcut that is the same as (ESC)“A”CHR$(12).
When you run this program with the DIP switch l-6 off (IBM
mode), you cannot get the printout as shown above.
The (ESC) “A” CHR$(n) command in IBM mode only defines
the line spacing as n/72 of an inch; the (ESC) “2” command
changes the line spacing to the amount defined by the previous
(ESC) “A”.
So: you need to change the following lines to the previous pro-
gram as shown below for the IBM mode:

40 LPRINT CHR$(27>;"A";CHR$(I);CHR$(27);w2';
80 LPRINT CHR$(27); "A";CHR$(12);CHR$(27);"2"

You may wonder why they picked l/72 of an inch as the incre-
ment for the line spacing command. There’s a good reason: the
dots that the printer makes are l/72 inch apart. So this means
that you can vary the line spacing in increments as fine as one
dot - unless you want finer spacing, like one third dot spac-
ing.

The (ESC)“3”CHR$(n) command sets the line spacing in in-

crements of l/216 inch. Change line 40 in your program so it is
like this:

40 LPRINT CHR$(27);"3";CHR$(I);

. and run the program again. Now the results will look like this:
45

The program works just the same as before, but the line spac-
ing are just one-third what they were. This is because (ESC j“3”
CHR$(n) sets the line spacing to n/216 inch.
Table 4-2 shows all the line spacing commands, including
several “shortcut” commands for commonly used line spacings.

Table 4-2
Line spacing commands

n Moving down the page without a carriage return

So far, all the commands that move the paper also move the
print head to the left margin. And normally this is what you
want. Sometimes, though, you may wish to move down the page
without moving the printhead back to the left margin. The
following commands do just that.
The (ESC)“J”CHR$(n) command causes the printer to make
one line feed of n/216 inch, but does not change the setting of the
line spacing. Try this program to see how it works:
46

NEW
10 ' Demo of'one-time line feeds
20 LPRINT "LINE NUMBER 1."
;; LPRINT "LINE NUMBER 2.";
' One-time line feed
50 LPRINT CHR$(27>;"J";CHR$(loO);
60 LPRINT "LINE NUMBER 3."
70 LPRINT "LINE NUMBER 4."
80 END

Here is what your printer will produce:

i-:1:IW I\Il.JMEE:FII. I
I__I Ntx I’dJMBER 2 n

I....I NE NIJMBEH 3.
L.:I:NE: NCJMBER 4 ,s

The (ESC)“J”CHR$(lOO) in line 50 changes the spacing to

100/216 inches for one line only without moving the printhead.
The rest of the lines printed with the normal line spacing.
Notice that both line 30 and line 50 end with semicolons. This
prevents the normal line feed from occurring.

The ‘(ESC)“j”CHR$(n) command works the same way except

that the paper moves in the opposite direction. Try this simple -
change to your program and see what a difference it makes!
-
-
40 ( One-time reverse line feed
50 LPRINT CHR$.(27);"j";CHR$(lOO);

L:CNE W..IME:EK 3 m
I__1 :;.IE tqI,_!
plE:E:Fi. it ”
Iem1:i\!- i’%]
I,..!
1’1E:1:F: j, .
iv 1 NE N!..!tqE:ER :z .
47

PAGE CONTROL

Now that we have seen how to control line spacing, we can go

on to page control - positioning the printing on the page and ad-
justing the paper length.

n Form feed
The simplest forms control code is the form feed. Form feed
(or < FF > ) is CHR$(12) and causes the printer to move the
paper to the top of the next sheet. Try it by changing lines 40
and 50 to this:

40 t form feed
50 LPRINT CHR$(12);

Before you run the program, turn your printer off and adjust
the paper so that the top of the sheet is even with the top of the
ribbon guide on the print head, then turn the printer back on. If
you don’t remember how to do this, review Chapter 2. When
you run the program, the results will look like this:

u I
---- J -------------
o 1.
:.:1.
1 ‘TNE
Nf-
.- iVl.JlviHl~R
IWMBER 3..
2.
,
f 0 I
0 I .t w-c -----------
0 pi;;; ;;;g ;I
I

.
The form feed (CHR$(12)) in line 50 caused the printer to
move to the top of a new page before printing the last two lines.

n Reverse form feed

Just as your printer can perform a reverse line feed, it can do a
reverse form feed. This code moves the paper so that the print
head is positioned at the top of the current page. This can be us-
ed, for example, to print text in a multi-column magazine for-
mat; print the first column, then reverse form feed back to.the
top of the page to start the second column. The code for reverse
form feed is easy to remember: < ESC > < FF > .

Table 4-3
Form feed commands
1Function 1Control code
Advance paper to top of next
CHR$(12)
paw
Reverse paper to top of current
(ESC)CHR$(12)
page

W Changing the page length

You may have some computer forms that you wish to use with
this printer that are not 11 inches high. That’s no problem,
because you can tell your printer how high the forms are that
you are using. There are two commands for doing this, shown in
this table.

Table 4-4
Form length control
Function Control code
Set the page length to n lines (ESC)“C”CHR$(n)
Set the page length to n inches (ESC)“C”CHR$(O)CHR$(n)

Let’s set up a 7 inch high form length, which is typical of

many computer checks. The following program will do it.

NEW
10 ' Demo of variable form lenffths
20 LPRINT CHR$(27>;"C";CHR$(O>jCHR$(7);
30 LPRINT "PAY TO THE ORDER OF:"
40 LPRINT CHR$(12);
2; ;;;INT "FAY TO THE ORDER OF:"

-
This program should print “PAY TO THE ORDER OF:”
twice, and they should be 7 inches apart. Line 20 sets the form -
length to 7 inches. After line 30 prints, line 40 sends a form feed
.-
49

advance the paper to the top of the next form. Line 50 then
prints its message.
After you have run this program, turn off the printer and ad-
just the top of form position. When you turn the printer back on
the page length will reset to its normal setting (usually 11 in-
ches).

TOP AND BOTTOM MARGINS

Many programs that you use a printer don’t keep track of

where they are printing on the page. This causes a problem
when you get to the bottom of a page because these programs
just keep on printing, right over the perforation. This makes it
very hard to read, especially if a line happens to fall right on the
perforation. And if you separate the pages then you are really in
trouble.
Of course your printer has a solution to this predicament. This
printer can keep track of the position on the page, and advance
the paper so that you won’t print too near the perforation. There
are two commands to do this. One controls the space at the top
of the page and the other controls the space at the bottom of the
page. The control codes are given in the following table.

Table 4-5
Top and bottom margin commands

Function Control code

Set top margin to n lines (ESC)“r”CHR$(n)
Set bottom margin to n lines (ESC )“N”CHR$(n)
Cancel top and bottom margins (ESC)“O”

In both cases the value of n tells your printer how many lines
to skip, although there is a slight difference in the usage. When
you set the top margin with (ESC)“r”CHR$(n), the value of n
tells the printer what line to start printing on. When you set the
bottom margin with (ESC)“N”CHR$(n), the value of n tells the
printer how many blank lines should be left at the bottom of the
page.
Let’s try a simple application to see how these margins work.
Enter this program, which will print 150 lines without top and
bottom margins.
10 ' Demo of top and bottom margins
60 LPRINT CHR$(12); :' form feed
70 FOR I=1 TO 150
80 LPRINT "THIS IS LINE";1
90 NEXT I
110 LPRINT CHR$(12) :' form feed
120 END

When you run this program it will print 150 lines right down
the page and across the perforations. When it’s done line 110
sends a form feed to advance to the top of the next page. Look at
the lines that have printed near the perforations. Separate the
sheets and see if any of the lines have been torn in half. These
are the problems that the top and bottom margins will solve.
Now add the following lines to your program. (Don’t forget
the semicolons or you won’t get quite the same results that we
did.)

20 1 Leave 6 blank lines at the bottom of page

30 LPRINT CHR$(27);"N";CHR$(6);
40 ' Start top of page at line 6
50 LPRINT CHR$(27);"r";CHR$(6);
100 LPRINT CHR$(27) poff; I clear top and bottom
margins

Now when you run the program, your printer skip the first six
lines and the last six lines on each page. Always send a form
feed after setting the top margin, or it will not work on the first
page printed. That’s because the top margin only takes effect
after a form feed.
Line 50 sets the top margin, line 30 sets the bottom margin,
and line 100 clears both margins when we are done.
THIS IS LINE 1
THIS IS ILINE 2
THIS IS LINE :
THIS IS ILINE 4
THIS I5 LINE 5
THIS IS ILINE 6
THIS IS LINE 7
THIS IS LINE R
THIS IS LINE 9

; THIS LINE 50
I THIS LINE 51
’ rHIS LINE 52
; THIS LINE 53
, THIS LINE 54
I THIS LINE 55

I
O1
ITHIS IS LINE 56

b-
THIS IS LINE 164
THIS IS LINE 105
0 THIS IS LINE 106
THIS IS LINE 107
THIS IS LINE 108
0 THIS IS LINE 109
THIS IS LINE 116

0
---
0
b.

0
THIS IS LINE 111
-.
0 THIS IS LINE 112
THIS IS LINE 113
THIS IS LINE 114
0 THIS IS LINE 115
THIS IS LINE lib
THIS IS LINE 117
0 THIS IS LINE 118
THIS IS LINE 119
- THIS IS LINE 120
9
L_
SETTING LEFT AND RIGHT MARGINS

The left and right margins of this printer work just like a
typewriter - once they are set all the printing is done between
them. The commands to set the margins are given in the follow-
ing table:

Table 4-6
Left and right margin commands

Try setting the margins with this program:

10 ' Demo of margins

20 GOSUB 70
30 LPRINT CHR$(27);"l";CHR$(lO);
40 LPRINT CHR$(27);"Q";CHR$(70);
50 GOSUB 70
60 END
70 FOR I=1 TO 80
80 LFRINT "XI';
90 NEXT I
100 LPRINT -
110 RETURN
-

The first thing that this program does is to branch to the

subroutine that starts in line 70 . This subroutine prints 80 X’s
in a row. The first time that the subroutine is used, all the X’s fit
in one line. Then line 30 sets the left margin to 10, and line 40
sets the right margin to 70. Once again the subroutine is used,
but this time the X’s won’t all fit on one line since there is now
only room for 60 characters between the margins.
Run the program. The results will look like this:

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
XxXXXXXXXxXXXXXxxxXXxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxx
53

When you want to reset the margins to the default values, you
have two choices. You can either turn the printer off and back
on, or you can set margin values equal to the default values.
This means that you should set a left margin of 0 and right
margin of 80 in pica pitch.
If you change the pitch of your printing after you set your
margins, the margins will not change. They stay at the same
place on the page. So if you set the margins to give you 65 col-
umns of printing when you are using pica type, then you change
to elite type you will have room for more than 65 columns of
elite printing between the margins.

HORIZONTAL AND VERTICAL TABS

Suppose you need to move across the page to a certain posi-

tion several times in a document. It’s not much fun to type in
space after space. And you don’t have to - you can “tab” your
way across the page.
Your printer’s tabs are like those on a typewriter, but much
more powerful. You have both horizontal and vertical tabs
which can be used for both text and graphics - and they’re real-
ly handy for indenting paragraphs and making tables.

,M Horizontal tabs
Horizontal tabs are set automatically every eight positions. To
move the print head to the next tab position, send CHR$(S).
Try this program to see how the default tabs work.

10 1 Demo of horizontal tabbing

20 LPRINT "ONE";CHR$(g);"TWO";CHR$(9);"THREE";
CHR$(g);"FOUR"

Here’s what you should get-

Even though the words are different length, they are spaced
out evenly by the horizontal tabs.
Now add the following line to your program to set different
horizontal tabs:
15 LPRINT CHR$(27);"D";CHR$(7);CHR$(l4);CHR$(21);
CHR$(O)

(ESC)“D” is the command to begin setting horizontal tabs. It

must be followed by characters representing the positions that
you want the tabs set. In our program we are setting tabs in col-
umns 7, 14, and 21. The CHR$(O) at the end ends the string of
tabs. In fact, any character that is not greater than the previous
one will stop setting tabs. This means that you must put all your
tab values in order, from least to greatest, or they won’t all get
set.
When you run the program now it produces this:

The words are now closer together, but still evenly spaced.
Turn your printer off and on again to reset the default tabs.

Table 4-7
Horizontal tab commands
Function Control code
Advance to next tab position CHWW
(ESC)“D”CHR$(nl)
Set tabs at nl, n2, etc.
CHR$(nZ).....CHR$(O)

n One-time horizontal tabs

Suppose you need to move to a position across the page, but
you only need to do it once. It doesn’t make much sense to set
up a tab to use only one time. There must be an easier way -
and of cause there is.
The solution is called a one-time tab. Table 4-8 show the com-
mands.

Table 4-8
One-time horizontal tabs
Function Control code
Absolute horizontal tab (ESC) ‘3” CHR$(nl) CHR$(nZ)
Relative horizontal tab (ESC) “\” CHR$(nl) CHR$(nZ:
,.

The aboslute horizontal tab command moves the print head to

a specified position on the page. The position that you want the
print head to move to (meaured from the left margin) is
specified by the values of $21and n2 in l/60-inch units using the
formula nl + n2 x 256.
Try this program to see how this works.

10 1 Demo of absolute horizontal tabs

20 FOR I=60 TO 70 STEP 2
30 LPRINT I;'+++++';
40 LPRINT CHR$(27);"$";CHR$(I);CHR$(O);
50 LPRINT 'Horizontal tab."
60 NEXT I
70 END

In this program, the print head is positioned before the “H” in

“Horizontal” is printed.

The relative horizontal tab command can move the print head
right form the current position. The formula for calculating how
much the print head moves is the same as in the absolute
horizontal tab command. However, the units by which the print
head actually moves vary’in l/120-inch units.

Try this program to see how this works.

10 FOR I=1 TO 3
20 LPRINT "Relative";
30 LPRINT CHR$(27>;'\';CHR$(I*2O);CHR$(O);
40 LPRINT 'Horizontal";
50 LPRINT CHR$(27);"\';CHR$(I*lO);CHR$(O);
60 LPRINT "Tab."
70 NEXT I
80 LPRINT
90 END

W Vertical tabs
Vertical tabs have the same kinds of uses that horizontal tabs
do - they just work in the other direction. Horizontal tabs allow
you to reach a specific column on the page no matter where you
start from. Vertical tabs are the same. If you have a vertical tab
set at line 20, a vertical tab (or <VT >) will move you to line 20
whether you start from line 5 or line 19.
The vertical tab is not set at the power-on default. If you send
a CHR$(ll), which is the ASCII code for <VT > , before we
have set up tabs advance the paper one line. Enter this program
to see how this works.

10 ' Demo of vertical tabs

40 LPRINT CHR$(ll);"FIRST TAB."
50 LPRINT CHR$(ll);"SECOND TAB."
60 LPRINT CHR$(ll);"THIRD TAB."
70 LPRINT CHR$(ll);"FOURTH TAB."

Now, let’s set some vertical tabs of our own. Add these lines
to the program:

20 LPRINT CHR$(27>;"B";CHR$(lo);CHR$(20);
30 LPRINT CHR$(4O);CHR$(5O);CHR$(O);

(ESC)“B” is the command to set vertical tabs. Like the

horizontal tab setting command, tab positions must be defined
in ascending order. Our example sets vertical tabs at lines 10,
20, 40 and 50. Then the CHR$(ll) in each of the following lines
advances the paper to the next vertical tab. The printout is
shown below.
j .

1-I-i I HC) TAM I

wx.m-1-i-4 -rAb.
.,

Add one more line to the program to demonstrate one more

feature of vertical tabs.

80 LPRINT CHR$(ll);"FIFTH TAB."

Now when you run the program the first page looks just like
before, but line 80 sends one more <VT> than there are tabs.
This doesn’t confuse your printer - it advances the paper to the
next tab position which happens to be the first tab position on
the next page. That’s nice, isn’t it?

Table 4-9
Vertical tab commands

Advance paper to next tab posi-

n Vertical tab channels

Vertical tab channels are especially helpful in two situations.
The first occurs when you are writing a program to accompany
a preprinted form that can accommodate various types of
responces. The second occurs when you create a multipage
form or report with different vertical tabs on each page. -

Table 4-10 -.
Vertical tab channel commands
Function Control code
Set vertical tabs at nl, n2, etc. (ESC)“b”CHR$(nO) CHR$W)
as channel n0 CHR$(nZ).....CHR$(O)
Select vertical channel n0 (ESC)“I”CHR$(nO)

You can store up to eight channels of tab stops. They are

numbered from 0 to 7. If you have already stored a set using
(ESC)“B” command, your printer has labelled it as channel 0.
Try this program how to see the vertical tab channels work.
10 1 Demo of vertical tab channels
20 LPRINT CHR$(27>;"b';CHR$(l>;CHR$(lO);CHR$(2O);
CHR$(O) ;
30 CLHPRHl~oT)CHR$(27);"b";CHR$(2);CHR$(15);CHR$(25);
.
2
40 ~~~~~~)CHR$(27);"b";CHR$(3);CHR$(l7);CHR$(28);
;
65: FOR
1 UseI=1
vertical
TO tab channels
3
70 LPRINT "TOP OF FORM"
80 LPRINT CHR$(27);"/";CHR$(I);
90 LPRINT CHR$(ll);
100 LPRINT "1ST TAB OF CHANNEL";1
110 LPRINT CHR$(ll);
120 LPRINT "2ND TAB OF CHANNEL";1
130 LPRINT CHR$(12);
140 NEXT I
150 LPRINT CHR$(27);"@"
160 END

When you run this program you should get like this.

TOP OF FClRM TOF’ OF FORM TOP OF Fllh’t’l

1ST TAB OF CHANNEL 2

1ST TAB OF CHANNEL 1:

ZND TAB OF CHANNEL 2

2ND TRB CIF CtiRNNEL. 3

f-w

In this program we set tabs at 10 and 20 in channel 1 in line

20. In line 30 we set tabs 15 and 25 in channel 2, and in line 40
we set tabs 17 and 28 in channel 3.
Because the channels are stored, you must make the printer to
recall one before you use it, so we used (ESC)“I”CHR$(nU) in
line 80.

CENTERING AND ALIGNING TEXT

Text can be arranged in any of three formats: left aligned (nor-

mal printing with “ragged” right margin), centered between the
margins, or right aligned. These are selected by the following
commands.

Table 4- 11
Aligning commands
Function Control code
Left-aligned printing (ESC)“a”CHR$(O)
Centered printing (ESC)“a”CHR$(l)
Right-aligned printing (ESC)“a”CHR$(2)

Try this program to see how easy it is.

10 "Demo of aligning and centering

20 LPRINT CHR$(27);"1";CHR$(20);
30 LPRINT CHR$(27);"Q";CHR$(60);
40 LPRINT CHR$(27);"a";CHR$(O);
50 LPRINT "THIS LINE IS LEFT-ALIGNED."
60 LPRINT CHR$(27);"a";CHR$(l);
70 LPRINT "THIS LINE IS CENTERED."
80 LPRINT CHR$(27>;"a";CHR$(2);
90 LPRINT "THIS LINE IS RIGHT-ALIGNED;"

When you run this program, you should get like this:

Tl-I I s L. I NE :I:t;- I.-.E:FT’-.I-Il....

I GI’.lEw:)
”

-r 1.4:[s I._:I.I\I EZ 1 s -r --.4 I....I G 111

w :I:G1.4 E 12m
CHAPTER 5

SPECIAL FEATURES OF
THE PRINTER

Subjects we’ll cover in Chapter 5 include-

* Printer’s bell;
l Master reset;

l Uni-directional printing;
l International character sets;

l Printing BIG characters;

l The optional sheet feeder;

l Macro instruction;

l Reading a hex dump.

In the previous chapters we have learned about several

groups of control codes. In this chapter we will look at more con-
trol codes. These codes don’t fit neatly into any of the groupings
that we have studied, but they add a lot of capability to your
printer. So here goes.

n Now hear this

You may have heard the printer’s bell if you have ever run out
of paper. And you may have wondered why it’s called a bell
when it beeps instead of ringing! It’s a long story that goes back
to the early days of computers, when teletype machines were us-
ed for computer terminals. These mechanical marvels had a bell
in them that could be heard for blocks. This bell was used to
signal the operator that somethings needed attention. The code
that the computer sent to the teletype machine to ring the bell
. was, reasonably enough, called a bell code. Well the name bell
code is still with us, even if the bell has changed to a beeper, and
a lot of people still call the beeper a bell, even if it doesn’t sound
like one. So with our trivia lesson out of the way, let’s see how
we can “ring the bell.”
The code to sound the “bell” is CHR$(7), which is ASCII code
7 or (BEL). Any time your printer receives this code it will
62

sound the bell for a quarter of a second. This can be used to re-
mind an operator to change the paper or to make another adjust-
ment to the printer.
You can try this by typing:

LPRINT CHR$(7)

n Resetting the printer

Up to now when we wanted to reset the printer to the power
on condition we have had to either turn the printer off and then
on again, or to send the specific codes that reset the particular
features. There is an easier way. The control code (ESC) “@”
will reset all of the printer’s features to the power on condition
(as determined by the DIP switches), with two exceptions.
Those exceptions are that (ESC) “a” will not erase any
characters that you have stored in the printer’s RAM memory
(Chapter 5 tells you how to create your own characters), and it
won’t erase the macro if you have one stored in the printer’s
RAM (this chapter will tell you how to create a macro).
In addition, if you set the “Panel” mode, “Italic” mode, or
“Italic and Panel” mode by the control panel settings at the
power on, these functions will be remain with this control code.

n Putting your printer to sleep

You know how to put your printer off line with the On Line
key on the control panel. Your printer has another off line state
that can be controlled from your computer. When you turn the
printer off line from your computer, this printer will ignore
anything that you send it, except for the code to go on line again.
CHR$(lS) is the code to turn your printer off line; CHR$(17)
turns your printer to on line status.

n Printing the bottom of the sheet

Sometimes when you are using individual sheets of paper you
may want to print near the bottom of a sheet. The paper-out
detector usually stops the printer when you are about 1 inch
from the bottom of the sheet. This is notify you if you are runn-
ing out of continuous paper.
Your printer has the ability to print right to the bottom of the
sheet. You can disable the paper-out detector so that it doesn’t
stop the printer. This will allow you to print to the end of the
sheet, and even beyond if you are not careful. The codes to con-
trol the paper-out detector, along with the other codes that we
have just learned are in the following table.

Table 5-1
Some miscellaneous commands

Function 1Control code

Sound bell 1 CHRU7J
1Master reset 1 (ESC) “a”
I Off line 1CHRW
On line CHR$il
Paper-out detector off WC)
Paner-out detector on (ESC) ,
I Move mint head back one sDace I CHRW 0
Delete last character sent CHR$(127)
Cancel text in print buffer CHR$(24)
I Print “slash zero” I (ESC) “-‘I 1
I Print “normal zero” 1 (ESC)’ “-“0
Immediate-print on (ESC) “i”1
Immediate-print off (ESC) “i”0

n Backspace, delete, and cancel text

Backspace (CHR$@)) “backs up” the printhead so that you
can print two characters right on top of each other. Each time
your printer receives a backspace it moves the printhead one
character to the left, instead of to the right. You can strike over
multiple letters by sending more than one backspace code.
Delete (CHR$(127)) also “backs up” one character, but then it
“erases” the previous character (it’s erased from your printer’s
buffer, not from the paper).
Cancel text (CHR$(24)) deletes all the text in the print buffer;
that is, in the line before the delete text command. Since your
printer prints one line of text at a time, only that line will be
deleted.
The following program shows how these codes works.

10 LPRINT "BACKSPACE DOES NOT";

20 LPRINT CHR$(8>;CHR$(8);CHR$(8);
30 LPRINT ~I=== WORK"
40 LPRINT "DELETE DOES NOT";
50 LPRINT CHR$(127);CHR$(127);CHR$(l27);
60 LPRINT "WORK"
70 LPRINT "CANCEL LINE";
80 LPRINT CHR$(24);
90 LPRINT "DOES NOT WORK"

Here is what this program will print:

The backspace codes in line 20 move the printhead a total of

three spaces to the left so that the first part of line 30 will over-
print the word “NOT”. The delete codes in line 50 “erase” the
three letters in the word “NOT” so that it doesn’t even print.
In line 80, CHR$(24) deletes the words in line 70. The
semicolon at the end of line 70 prevents a line feed from causing
that line to print before the printer receives the CHR$(24) code.
The text in line 90 prints as it normally would because it is after
CHR$(24).

n Printing zeroes
Believe it or not, there are two types of zeroes. There is of
course the type we use every day - 0 - and this is what your
printer will print if you don’t do anything.
The other type is used almost exclusively in computers and
engineering. It is called the “slash zero” and is written like this -
0. The line through the number is supposed to prevent you from
misreading it as the letter “0”. Back before high-quality
printers were available, this was a good idea but you really have
no need for it (although you may want to use the slash zero for
special effect).

W Immediate-print
This printer can print at fine rate of 120 characters per se-
cond. But it will also print more slowly at the speed of your typ-
ing. In immediate-printmode, the printhead prints one character
at a time, as you send it. This printer also moves the paper up so
that you can see the current line and then down to continue
printing.
65

You can turn immediate-print mode on with (ESC) “i” 1. But

before looking at it, let’s review the normal operation of the
print buffer. Enter this program.

20 A$="" : INPUT " TYPE A CHARACTER ",A$

30 IF A$="" THEN 50
40 LPRINT A$; : GOT0 20
50 LPRINT : LPRINT CHR$(27);"@"

Now type several characters, and after each press the

RETURN key. True to form, the printer just stuffs the
characters into its buffer while it waits for a carriage return
code. (In this program the RETURN key doesn’t send a car-
riage return code.) To end this program and print the contents
of the buffer, press RETURN alone.
Now add this line:

10 LPRINT CHR$(27);"il";

And RUN the program. Your printer responds to your typing -

immediately.
’ When you are finished, press RETURN alone.

n Adjusting the width of space between characters

This printer provides a command that adjusts the space be-
tween the NLQ characters that it prints when the DIP switch l-
6 is set on. The (ESC) CHR$(32) CHR$(n) command adds blank
space between the characters. The units of space that are added
vary in l/60-inch units.

Try thisprogram to see how thisworks.

10 ’ Demo of adjusting spaces

20 LPRINT CHR$( 27);"xl";
30 FOR I=10 TO 1 STEP -2
40 LPRINT CHR$(27);" ";CHR$(I);
50 LPRINT "This line is added";I;"spaces."
60 NEXT I
70 LPRINT "This line is Normal space."
80 END
This line is added 10 spaces.
This line is added 8 spaces.
This line is added 6 spaces.
This line is added 4 spaces.
This line is added 2 spaces.
This line is Normal space,

This command can be used to produce micro-justification,

which is a method of justifying lines by incresing the space be-
tween each character.

n Uni-derectional printing
Uni-directional printing is a big word that means printing in
one direction only. Your printer normally prints when the print-
head is moving in both directions. But once in a while you may
have an application where you are more concerned about how
the vertical lines align than with how fast it prints. This printer
lets you make this choice. The table below shows the commands
for controlling how this printer prints.

Table 5-2
Printing directin commands
Function Control code
Print ih one direction (ESC) “U”l
Print in both directions (ESC) “U”0 -
One time mint in one direction (ESC) “0’

Try this program to see the difference that printing in one - -

direction makes.

10 ) Demo of uni-directional printing

20 LPRINT CHR$(27);"1";
30 FOR I=1 TO 10
40 LPRINT 111"
50 NEXT I
60 LPRINT : LPRINT
70 LPRINT CHR$(27) ;"Ul";
80 FOR I=1 TO 10
90 LPRINT "I"
100 NEXT I
110 LPRINT CHR$(12);CHR$(27);"@"
67

Here is what you will get. The top line is printed bi-directional-
ly, and the bottom is printed uni-directionally. You will have to
look hard because there isn’t much difference.

Let’s analyze the program. Line 20 sets the line spacing to

7/72 of an inch so that the characters that we print will touch top
to bottom. Lines 30 - 50 print 10 vertical line characters. Then
line 70 sets one-direction printing and the vertical lines are
printed again. Finally line 110 sends a form feed to advance the
paper to the top of a new page, and then uses the master reset to
restore the printer to the power on condition.
You can also set the printer to print in one direction for one
line only by using the (ESC) “(” command. This command im-
mediately moves the printhead to the left margin and then
prints the remainder of the line from left to right.

W The seven bit dilemma

Certain computers (but not the IBM-PC fortunately!) don’t
have the capability to send eight bits on their parallel interface.
They can only send seven bits. This would make it impossible
for these computers to use this printer’s block graphics
characters and special symbols if our engineers hadn’t thought
of a solution. (All of these characters have ASCII codes greater
than 127 which means that the eighth bit must be on to use
them.) The solution lies in the three control codes given in the
following table:
Table 5-3
Eighth bit controls
Function Control code
Turn the eighth bit ON (ESC) “>”
Turn the eighth bit OFF (ESC) “=”
~ec~~~~;t~ bit “as is” from ( ESC > ,,#,,

n Block graphics characters and special symbols

Besides the upper and lower case letters and symbols that we
are by now familiar with, your printer has a whole different set
of characters that are for special uses. These characters include
block graphics for drawing forms and graphs, and special sym-
bols for mathematical, engineering and professional uses. The
special characters are included in two character sets. The
character set you normally use with IBM mode is called
character set #l. The special characters are printed out when
you send ASCII codes 160-255 to the printer.
Your printer also offers character set #2 which is almost the
same as character set #l except for the addition of ASCII codes
3-6,21, and 128-159. Character set #2 is selected with (ESC)
“6”; to go back to character set #l, use (ESC)“7”.
You can also specify the power-on default character set by set-
ting DIP switch l-7 on for character set #l and off for character
set #2. The following program will print out all of the graphics
characters available:

10 LPRINT CHR$(27);"0";
20 LPRINT CHR$(27);"6";
30 FOR J=3 TO 6
40 LPRINT " d';J;CHR$(J.);CHR$(9);
50 NEXT J
60 LPRINT " 20 ";CHR$(20)
70 LPRINT
80 LPRINT " 21 ';CHR$(21);CHR$(g);
90 LPRINT " 26 ";
100 LPRINT CHR$(26)
1'20LPRINT
130 FOR ~=128 TO 254 STEP 5
140 FOR I=J TO J+4
150 IF I>254 THEN 170
160 LPRINT I;CHR$(I);CHR$(g);
170 NEXT I
180 LPRINT : LPRINT
190 NEXT J
I;:-
::>
69

Figure 5- 1. Character set #2

Figure 5-l shows what this program will print. If your chart
doesn’t 1001like this because it has regular letters and numbers
instead of the special symbols, then your computer is only using
seven bits. You can get the correct printout by changing line
160 to this:

160 LPRINT I;CHR$(27);">";CHR$(I);CHR$(27);"=";

CHR$(9);
A note for the IBM-PC users.
When you run this program, you cannot get the right-pointed
arrow (CHR$(26)) with the IBM-PC computers. This is because
the IBM-PC does not send this code to the printer.
There is a solution to avoid this problem. Change lines 100
and 120 to the either set of the following lists.

100 O=INP(&H379) : IF 0~128 THEN 100

110 OUT &H378,26 : OUT &H37A,5 : OUT &H37A,4
120 LPRINT : LPRINT

100 O=INP(&H3BD) : IF 0~128 THEN 100

110 OUT &H3BC,26 : OUT &H3BE,5 : OUT &H3BE,5
120 LPRINT : LPRINT

SO show are all of these strange characters used? Here is a

short program that demonstrate how the graphics characters
can be combined to create a figure: the 5 of clubs.

10 LPRINT CHR$(27);"6"; -.
20 LPRINT CHR$(218);CHR$(l96);CHR$(l96);
cHR$(l96);CHR$(l96);CHR$(l96);CHR$(19l)
30 LPRINT CsR$(l79);CHR$(53);CHR$(32);cHR$(32);
CHR$(32);CHR$(32);CHR$(l79)
40 LPRINT CHR$(l79);CHR$(32);CHR$(5);CHR$(32);
CHR$(5);CHR$(32);cHR$(l79)
50 LPRINT CHR$(l79);CHR$(32);CHR$(32);cHR$(5);
. CHR$(32);CHR$(32);CHR$(179)
60 LPRINT CHR$(l79);CHR$(32);CHR$(5);CHR$(32);
CHR$(5>;CHR$(32>;CHR$(179)
70 LPRINT CHR$(l79);CHR$(32);CHR$(32);CHR$(32); -
CHR$(32>;CHR$(53);CHR$(179)
80 LPRINT CHR$(l92>;CHR$(l96);CHR$(l96);
CHR$(l96>;CHR$(l96>;CHR$(l96);CHR$(217) -
90 LPRINT CHR$(27);"7"
71

If you have a 7-bit interface, add the following lines to the pro-
gram given above:

15 LPRINT CHR$(27);">";
95 LPRINT CHR$(27);"="

In this program line 10 selects character set #2 so that all the

graphics characters can be used (including the “club” sym-
bol). Then lines 20-80 print the 5 of clubs figure. Line 90
cancels character set #2 (which is the same as selecting
character set #l).
Here is what this program prints:

,H International character sets

Your printer is a multi-lingual printer for it can speak in
eleven languages! Your printer changes languages by changing
12 characters that are different for the different languages.
These sets of characters are called international character sets.
The control,codes to select the international character sets are
given in Table 5-4.
72

Table 5-4
International character set commands
I Countrv

The characters that change are shown beneath their ASCII

code in Table 5-5.

Table 5-5
International character sets
Country ~35~36~64~91~92~93~94~96~123~124~125~12
U.S.A I#lsl@lcl\lll*l’lcl:l,l~
IFrance
IGermany l#l$lsl~l~lul^l’l~lal~lR -
England f al~lrl~lil~l~l~l~l~l-
.I. G I.
Demarktype I #$@E~L-zi;;-
Sweden #rl~At5AUBZ~Bi.i
Italy

n Printing characters in the control code area

When you refer the Appendix B, you’ll find many characters
are printed in the control code area. (Remember that the low-
order control codes are the ASCII codes 0 through 31 plus 127,
and the high-order control codes are 128 through 159 plus 255.)
-
These codes don’t normally print symbols on paper, rather
they cause the printer to change modes. To make them print as
-
normal symbols requires an extra command. For example, the
73

command to “normalize” the high-order control codes is (ESC)

“6”. Try this program with the DIP switch 1-6 on.

10 ’ Demo of characters in the high-control code

area
20 LPRINT CHR$(27);"6";
30 FOR I=128 TO i59
40 LPRINT CHR$(I);
50 NEXT I
60 LPRINT CHR$(27);"7"
70 END

When you run this program you’ll get like this:

That’s where the italic international characters have been

stored. So the (ESC)“G” command without the (ESC)“R” gives
you access to the international characters. The (ESC)“7” turns
these characters back into control codes.
The low-order control codes can also be defined, but not all of
them can be printed with ease. The (ESC)“I” 1 command
makes them printable, and the (ESC)“I”O command returns
them normal.
Just as the higher control codes hide the italic international
characters, the lower control codes hide the roman international
characters.
Let’s see how these commands work with the following pro-
gram:

* Demo of characters in the control code a?e

;: LPRINT CHR$(27);"11";
30 FOR I=0 TO 6
40 LPRINT CHR$(I);
50 NEXT I
60 LPRINT CHR$(16);CHR$(17);
70 FOR I=21 TO 31
-80 LPRINT CHR$(I);
90 NEXT I
100 LPRINT
no FOR 1=128 TO 134
120 LPRINT CHR$(I);
74

130 NEXT I
140 LPRINT CHR$(144);CHR$(145);
150 FOR I=149 TO 159
160 LPRINT CiSS(I);
170 NEXT I
180 LPRINT CH?.$(27);"10"
190 END

When you run this program you should get like this:

Table 5-6
Control code area colmmands
Function Control c
Printable code area expansion (ESC)“G”
..
Control code area expansion 1 (ESC>“7”
C I (ESC)“I”l
kkct undefinedcodesas characters
(Cancelundefinedcodesas characters I (ESC)“I”O

n Printing BIG characters

You can even enlarge your character sets for attention-grabb-
ing headings or special effects. There are six commands you can
use. Everything following any of them will be enlarged as
shown below, until the cancel code is entered. -_

-.
Table 5-7
Big character cornmands
Function Control c
Double-high enlarged print (ESC)“h”( :HR$UJ I
Quad-high enlarged print (ESC)“h”CHR$(2)
1Double-highlower-halfenlarged mint 1 (ESC)“h”( :HR$(3)
.Double-highupper-halfenlarged print (ESC)“h”CHR$(4)
Quad-highlower-halfenlarged print (ESC)“h”( ;HR$(5) I
Quad-highupper-halfenlarged print (ESC)“h”CHR$(G)
I Cancel enlarged print 1 (ESC)“h”( ZHR$(O)

Try this program to see the big characters.

I
;.”
75

10 ' Demo of BIG characters

20 LPRINT "THIS IS I';
30 LPRINT CHR$(27);"h";CHR$(l);
40 LPRINT "DOUBLE";
50 LPRINT CHR$(27);"h";CHR$(O);
60 LPRINT " SIZED PRINTING."
70 LPRINT
80 LPRINT "THIS IS I';
90 LPRINT CHR$(27);"h";CHR$(2);
100 LPRINT "QUAD";
110 LPRINT CHR$(27>;"h";CHR$(O);
120 LPRINT " SIZED PRINTING."
130 END

When you run this program, you will get like this:

As you can see, when the big character command is used, the
baseline for each character does not align. When you want to
?lign the baseline, try this program:

10 ’ Demo of aligning BIG characters

20 LPRINT "THIS IS 'I;
30 LPRINT CHR$(27);"j";CHR$(21);
40 LPRINT CHR$(27);"h";CHRS(l);
50 LPRINT "DOUBLE";
60 LPRINT CHR$(27);"h";CHR$(O);
70 LPRINT CHR$(27);"J";CHR$(18);
80 LPRINT " SIZED PRINTING."
90 LPRINT :LPRINT :LPRINT
100 LPRINT "THIS IS 'I;
110 LPRINT CHR$(27);"j";CHR$(63);
120 LPRINT CHR$(27);"h";CHR$(2);
130 LPRINT "QUAD";
140 LPRINT CHR$(27);"h";CHR$(O);
150 LPRINT CHR$(27);"J";CHR$(63);
160 LPRINT " SIZED PRINTING."
170 LPRINT :LPRINT
180 END
When you run this program, you will get like this:

n The optional sheet feeder

The automatic sheet feeder is a handy option that feeds single
cut sheets automatically. Work done on cut sheets looks better
that done on computer paper, and you don’t have to tear the
“ears” off each sheet as you must with fan-fold paper.
The automatic sheet feeder feeds a new sheet automatically
every time the printer receives or generates a form feed. Any
time you wish, you can turn the auto-feed unit on and off by
using control codes.

Table 5-8
Automatic sheet feeder commands

When the automatic sheet feeder is installed, you must set the
DIP switch 1-5 on to detect the paper-out condition.
In addition, following functions are ignored when the auto-
matic sheet feeder is installed:
Setting of the page length
Top and bottom margins
Vertical tab settings

n The macro control code

The last of our group of miscellaneous codes is definitely not
the least. It is a user-defined control code, called a macro control
code. The term macro is from the jargonese macro-instruction
77

which refers to an instruction that “calls,” or uses a group of nor-

mal instructions. In computer programming macro-instructions
(which are similar to subroutines) save programmers a lot of
time and effort. Your printer’s macro can save you a lot of time
and effort also.
Here is how the printer’s macro works. You define macro by
telling the printer what normal control codes are to be included
in the macro. Then you can use the macro any time that you
want and the printer will do all the things that you included the
macro definition. You can include up to 16 codes in a single
macro. You can even use the macro to store a frequently used
word or phrase. There are two control codes for the macro: one
to define it, and one to use it. They are given in the Table 5-9.

Table 5-9
Macro instruction commands

Function Control code

(ESC)“+“...(codes you include)
Define macro
. . . CHR$(30)
Use macro (ESC)“+“CHR$(l)

To see how this works we can build a macro that will reset the
printing style to normal, no matter what style it may be to start
with. The following program will define a macro to do this.

10 LPRINT CHR$(27);"+"; 'Start macro

20 LPRINT CHR$(27);"h";CHR$(O); 'Big character
off
30 LPRINT CHR$(27);"!";CHR$(O>; 'Select normal
pica
40 LPRINT ~~~$(27);"Tfl; 'Super &
subscripts off
50 LPRINT ~H~$(27);'*211; lSet l/6 inch
line spacing
60 LPRINT CHR$(27);"a";CHR$(O); 'Left-aligned
printing
70 LPRINT CHR$(30) 'End macro
definition

As the comments in the program, we started to define macro

in line 10. Line 20 cancels the big character printing. Line 30
sets the normal pica, and also this command cancels the propor-
78

tional pitch, condensed print, expanded print, boldface, em-

phasized, and the underlining. Line 40 cancels the superscripts
and the subscripts. Line 50 sets the line spacing to l/6 inch, and
line 60 sets the left-aligned printing. Then, line 70 ends the
macro definition. This printer will remember this macro until
the power is turned off or until a new macro is defined. A macro
can hold up to 16 bytes (characters) of information. The one that
we defined contains thirteen.
Now that you have defined a macro, let’s see how to use it.
This program will print one line using several printing features.
Then it “calls” the macro in line 60. When line 80 prints the
style is “plain vanilla” because the macro has reset it.

10 LPRINT CHR$(2'7);"Q";CHR$(40);
20 LPRINT CHR$(27);"af';CHR$(2>;
30 LPRINT CHR$(27);"-1";
40 LPRINT CHR$(27>;"h";CHR$(l);
50 LPRINT "TESTING ABCD"
60 LPRINT CHR$(27>;"t";CHR$(l);
;; g;I?INT"TESTING ABCD"

TIES-b I--....
_.__.,_-.-,.. INI:
- _.-.....-..-..,. AIBC::ll2
“___I-.......-...
lIZ.S'T
1:IG AECI?

n Reading a hex dump

We’ve seen how to make a hex dump in Chapter 1, but it’s not
really clear what we can do with one. We need a little
background first.
The BASIC in some computers changes ASCII codes before
they send them to the printer. If you run into problem because
of this, try this hex dump to check the ASCII codes.
First turn off the printer and run the following program. Hold
down both the Paper Feed key and Mode key and turn on the
printer.

10 FOR I=0 TO 255

20 LPRINT CHR$(I);
30 NEXT I
40 LPRINT
50 END
79

If your system passes the codes directly to the printer without

changing them, you will get like this. (You can print out the last
remaining line in the print buffer by putting the printer off line
with the On Line key.)

a:,,:,01 02 I:)? 04 05 06 07 ................

If.1 11 I:: 1.3 14 15 16 17 . . . . . . . . . . . . . .
20 21 2” 23 24 25 26 27 28 29 20 2H 2C 2D X ?F * ; “#9X?!’ ox+.-./
70 ?I 3? 7, 34 3s 36 37 7.8 39 3a 3” TC 3D 7E 7;f’ 0127.4sh-7B9: : <Y’>”
40 41 42 43 44 45 46 47 48 49 40 48 4C 41) 4E 4F l~~RCDEFT7tiJ.Jt’LMNO
50 St s2 53 54 55 56 57 58 59 5f1 5% 5C 5D 5E 5F PORSTlJVWXYZC\ I”,-
60 61 62 6: 64 65 66 67 4R 69 6A 6P 6C 6D 6E 6F ‘nhcdef qhi -ib 1 mm
71) 71 72 73 74 75 76 77 78 79 7A 7B 7c 7D 7E 71. pqrstuvwxyz:ll”.
80 Al 02 Es? 04 El5 86 87 BE 89 RA BB EK RD SE rjf- . . . . . . . . . . . . . . . .
70 71 72 73 94 75 96 97 98 99 9A 9B 9C 9I.I 9E 9F
60 01 A2 a3 44 a5 Cl6 F17 648 F19 AA FIR AC RD fiE FIF ................
PO RI H2 83 B4 B5 Rh B7 BE3 B9 BFI RH BC SD BE BF ................
co Cl C2 C3 c4 cs Cb c7 CE C9 CA CB CC CD CE CF ................
DO Dl D2 D: D4 D5 Db D7 DB D9 DCI DR DC DD DE DF ..... ...........
EO El Er) E3 E4 E5 Eb E7 ES E9 EA EB EC ED EE EF ................
FL> Fl F2 F3 F4 FS Fb F7 FE F9 F0 FE FC FD FE FF ................
ou Oh ..

Most BASICS, however, are not quite that straight forward.

For example, the IBM-PC prints like the following.

Or:, 0 1 02 03 Q4 05 06 07 00 09 OA OB IX 0D I:Ii? 0E
0F 10 11 12 13 14 15 16 17 18 19 lB 1C ID 1E if- ............
’ 20 21 22 23 24 25 26 27 28 27 20 28 2C 2D 2E “F ‘;~~k*zv o*+,-./
‘I.0 31 32 33 34 35 36 37 38 39 74 3f1 7.C 3D TE :.F ,:,I 2.3456789: : .C= %--
40 41 42 43 44 45 46 47 4R 49 40 4R 4C 41, 4E 4F- I~nBTDEFStiI.J~L.FINO
50 51 52 s3 54 55 56 97 50 59 sa 5R SC 51) 51-I 5f- KIRRTUVWXY7C\l”-
60 61 h:! 63 64 65 66 67 6R 67 60 6B 6C 6D 6E 6r ‘ahcdefghiiI.lmno
70 71 72 73 74 7s 7h 77 7R 79 7FI 7H 7C 7D 7E 7F pqr.‘.tLlvW:<y;ICI:“.
En 01 82 93 84 85 Oh 87 RR 87 RR Elf3 BC nu RI7 I-IF . . . . . . . . . . . . . . . .
71.1 91 92 93 94 95 96 97 9R 99 90 9B 91: 9D 9E 9F . . . . . . . . . . . . . . . .
ra1.J at A2 a.3 A4 05 aa 07 At3 A9 Ah AR FIG RD AE nF . . . . . . . . . . . . . . . .
HO Bl B? R3 B4 85 86 R7 BEI B9 PA RB EC BD BE Bt- . . . . . . . . . . . . . . . .
CO Cl C2 C3 C4 C5 C6 C7 CO C9 CF\ CR CC CD CE r:F . . . . . . . . . . . . . . . .
DO Dl DI! D3 D4 D5 Dh D7 DO D9 DA DR DC DD DE DF ................
EO El E2 E3 E4 E5 E6 E7 ES E9 EA EB EC ED Et: EF ................
F0 Fl F2 F3 F4 F5 F6 F7 FB F9 Fe FB FC f=D FE FF ................
0D UFI ..

Notice that your printer is receiving decimal code 13 (hex OD)

is coming with hex OA, which is really decimal 10. In addition,
your printer does not receive decimal code 26 (hex 1A).
Your printer prints hex numbers 16 per line, with printing the
characters on the right side. If it receives less than 16, it sits in a
holding pattern, awaiting more data. Taking the printer off line
80

dumps the characters to the paper.

To debug a program quickly, just use the hex dump capabili-
ty. Appendix B will help you translate the hex codes to ASCII
equivalents.
CHAPTER 6

CREATING YOUR
OWN CHARACTERS

Subjects we’ll cover in Chapter 6 include -

l Designing and printing your own characters;

l Designing proportional characters ;

l Designing your own characters with NLQ.

In the previous chapters of this manual you’ve learned how to

control the printer to give dozens of different typefaces. By us-
ing various combinations of pitches, character weights, and font
selections, you can create nearly any effect you want to in text.
And with international character sets and the special text and
big characters described in Chapter 5, you can print almost any
character you think of.
But if “almost any character” isn’t good enough for you, then
it’s a good idea you have this printer! With it you can actually
create your own characters. As you’ll see in this chapter,
download characters can be used to print a logo, special
characters for foreign languages, scientific and professional ap-
plications, or any other specific printing task.

DOT MATRIX PRINTING

In order to create download characters, you’ll need some

understanding of how dot matrix printers work. They’re called
“dot matrix” because each character is made up of a group of
dots. Look closely at some printed characters produced by your
printer and you will see the dots. Figure 6-1 shows how the let-
ter “C” is formed by printing 15 dots.
The printhead in this printer consists of nine wires stacked
one atop the other. Figure 6-2 shows an enlarged schematic
view of the front of the printhead, showing the ends of the wires
and their relationship to the printed draft characters. As you can
see, the capital letters use the top seven wires of the printhead,
and the descenders (such as the lower case “p” shown) use the
bottom seven pins. As the printhead moves across the page (in
either direction - that’s what is meant by bi-directional print-
ing) it prints one column of dots at a time. Each time a dot is sup-
posed to print an electromagnet inside the printhead causes the
appropriate wire to strike the ribbon (making this printer an im-
pact printer).

I
Figure 6- 1. The letter “C” is created by printing 15 dots.

5gure 6-2. As the printhead moves across the page, each of the
wires prints one row of dots.

THE PRINT MATRIX

All of the standard characters that this printer prints are form-
ed from patterns of dots that are permanently stored in the
printer’s ROM (read-only memory). This includes all of the stan-
dard ASCII characters, and special characters, the international
83

character sets, and the NLQ characters.

But there is another area of memory in this printer reserved
for user-defzked characters. These are characters that you can
design and download into the printer. When download
characters are defined they are stored in RAM (random access
memory), which allows you to define or modify them at any
time.
Each of these characters, whether it is from the standard
character ROM or in download RAM, is constructed on a grid
which is six “boxes” by nine “boxes” high. In addition, a dot can
straddle any of the vertical lines. As an example, take a look at
the enlarged “9” superimposed on the grid in Figure 6-3. As you
can see, some dots are inside the boxes, and some are centered
on the vertical lines. This, in effect, makes the character grid 11
dots wide by 9 dots high. To see how the rest of the characters
in the standard character ROM are constructed, take a look at
Appendix C.

L ___ _ . -..
Figure 6-3. Dots can be inside boxes or straddle the vertical lines
of the grid.

DEFINING YOUR OWN CHARACTERS

You’ve seen how these characters are designed by using a

grid to layout the dots. Now you can define characters exactly
the same way. Make up some grids (photocopy Figure 6-4 if you
wish) and get ready to be creative! (Just in case you are not feel-
ing creative, and to make our explanations a little clearer, we’ll
be using a picture of a chemist’s flask as an example of a draft
download character. You can see how we’ve laid it out in Figure
6-5. Later in this chapter we’ll use this character to create a
small graph.)

m,m,m,m.m,m,m,m,m,m,,m,,

ASCII Code

Descender

32 Start column
End column
16

M, = Descender l 128 + (Start * 161 + End

Total

i
ETigure 6-4. Use this grid (or one similar to it) to define your owr 1
draft characters.

You’ll notice that Figure 6-4 includes a lot of informatior 1

around the grid. Don’t be intimidated; we’ll explain each item as
we come to it in our discussion of defining and actually printing
download characters. You may have noticed another difference
between this grid and the one sh.ow in Figure 6-3: it’s only eight
boxes high. Which leads us to . . .

H Rule 1: Draft download characters are eight dots high

As you noticed in Figure 6-2, capital letters, most lowercase
letters, and most special characters use only the top seven pins
of the printhead. Draft download characters can go one better:
they can use as many as eight of the nine wires in the printhead.
So our grid is eight dots high.
It’s also possible to use the bottom eight pins, just as the “g”,
“-73 “ >9
19 P7 “q”, and “y” of the standard character sets do. These
are called descenders (because the bottom of the character
descends below the baseline of the rest of the characters).
I.
85

One bit in the download character definition command is to be

treated as a descender or not. We’ll get to the command in due
time. For now, if your character uses the top eight dots, write in
a one next to the word “Descender” on the layout grid; if it uses
the bottom eight dots, write in a zero. In our example, we’ll
want to the bottom of the flask to line up with the baseline of the
other characters, so it will not be a descender. As shown in
Figure 6-5, we’ve written in a “1” on out grid.

m,m,m,m.m,m,m,m,m,m,,,m.,

128 ASCII Cede

64 Descender 1

32 Start column
End column
16

8 M. = Descender l 128 + (Start l 161 + End

blal

Figure 6-5. We’ve designed a character and decided that it woulc

not be a descender, hence the “1” written in.

n Rule 2: Dots cannot overlap

As you can see in Figure 6-5 our flask has a nearly continuous
outline. But, you may ask, why not make it a really solid line and
print all the intermediate dots, as shown in Figure 6-6? Because
the dots that straddle the vertical lines in the grid actually
overlap those inside the boxes. If we tried to print overlapping
dots, the printhead would have to slow down and back up to
print both dots - not very efficient! To avoid this inefficiency,
this printer will not allow you to define a character like Figure 6-
6. (Actually, you can define it, but when it prints, your printer
will leave out the overlapping dots, so that it would print like
Figure 6-5.)
1

m m, m, m, m. m. m m, m. m m

ASCII Code
WRONG!
64 Descender

32 Start column
End column
16

M, = Descender l 128 + (Slat1 * 16) + End

Tolal

i
Figure 6-6.
cots cannot overlap; those in immediately adjacent
“half columns” will be ignored when the character is printed.

W Add up each column of dots

Now it’s time to give our creative side a break and get down to
some basic arithmetic. That’s where the numbers down the left
side of the grid come in. Notice that there is a number for each
row of3dots and that each number is twice the number below it.
By making these numbers powers of two we can take any com-
bination of dots in a vertical column and assign them a unique
value. Some examples will make this clearer. As shown in
Figure 6-7, if we add the numbers for the dots that print in a col-
umn, the sum will be a number in the range of 0 to 255. Each
number from 0 - 255 represents a unique combination of dots.

128 O-128
64 0 - 64 0 - 64
32 0 - 32 . - 32 l - 32
/ 16 0 - 16 0 - 16
/- 8 O-8 o-8
4 o-4 O-4
! 2 o-2 O-2 o-2
1 O-l O-1
~ ___
Sum 103 58 255

Figure 6-7. By adding the values of each dot in a column, you’ll get
a unique description for any combination of dots.
87

So add up the values of the dots in each column using this

system. In Figure 6-8 we’ve shown our grid with the sums of the
columns filled in across the bottom (see if these agree with your
answers!). Across the top of the grid you’ve probably noticed
the cryptic labeling of each column: ml, m2, m3, etc. These
labels correspond to the labels in the command syntax state-
ment, which we’ll get to shortly.

128
m. m, m, m. m, m, m, mR mp m,,. m,,

ASCII Code
I
64 Descender

32 Start column
End column
16

M, = Descender * 128 + (Start * 16) + Enc

/
pigure 6-8. Add the values of the dots in each column and write
the sum of each column at the bottom.

n Assigning a value to your character

We’ve done a pretty through job of designing and describing a
user-defined character. But this printer has room for 96
download characters - how does it knows which standard
character we want to print: every character is assigned a unique
number.
The standard characters are assigned the ASCII codes -
numbers from 0 to 255. For the download character sets you can
also define any positions between 0 to 225. This means that
once a character is defined and assigned a value (and the
download character set is selected, you can use that character
on the printer the same way you would any standard character.
You can send the character with the same ASCII value. You can
also access the character from a BASIC program with the CHR$
function.
There are no rules or restrictions on the use of numbers. This
means you can use whatever is most convenient for you -
perhaps seldom-used keys can be replaced by more useful
characters. In our example, we’ll assign the flask a value of 60,
which is the code for the character “(” in the ASCII characters.
A rather arbitrary selection, but this printer doesn’t care!
Our chart would hardly be complete with just a picture of a
chemist’s flask, so in Figure 6-9 we’ve made completed grids for
some other symbols: an automobile and a gun (quite a strange
mix of characters!). The information on the grids is now com-
plete (except for proportional width data - a more advanced
topic we’ll take up shortly).

Tigure 6-9. Character designs for the three graph symbols.

I1. : :

n Download character definition command

You’ve read through a long explanation of download
characters and we haven’t even told you the command syntax
yet! Now the wait is over. This is the most complex command in
your printer repertoire and now you’ve got the necessary
knowledge to implement it. Here it is:

(ESC)“&“CHR$(O) nl n2 m0 ml m.2 m3 m4 m5 m6 m7 m8 m9
ml0 ml1

Like the other printer’s commands, it starts with an (ESC)

(CHR$(27)). The next character is an ampersand (&) (CHR$(38))
followed by a CHR$(O).
nl and n2 are used to specify the ASCII values of the
characters you are defining. The reason that there are two bytes
reserved for this is that your printer allows you to define many
characters with just a single command. nl is used to specify the
beginning of a range of characters to be defined; n2 specifies the
end of the range. For instance, if you wanted to change the ap-
pearance of the numerals from 0 to 9 (which have ASCII codes
48 through 57), the command would begin with (ESC) “&”
CHR$(O) CHR$(48) CHR$(57) . . . Of course, you can also define
individual characters by making nl and nZ equal.
m0 is called the attribute byte, for it describes two attributes
of the character we have designed: descender data and propor-
tional width information. A byte consists of eight bits. In the at-
tribute byte, the first (high order) bit is used for the descender
data, and the last seven bits are used for proportional widths.
We’ll be discussing proportional character widths in detail later
in this chapter; for now, we’ll leave it at 11. The descender data
was descussed earlier: to use the top eight pins, this bit should
be 1; to use the bottom eight pins this bit should be 0. Figure 6-
10 shows the bits of the attribute byte as we’ll use them for our
flask character. By now you’ve probably seen an easier way to
determine the value of the attribute byte. Instead of translating
everything to binary, merely assign the descender data a value
of 128 (the value of the first bit) if you don’t want descenders, or
0 if you want descenders. Then just add the descender data to
the proportional width. This way, it’s simply a matter of adding
two decimal numbers. (In our case, it’s 128 + 11 = 139.)
L Descender

Figure
date

6-10.
0 000
Starting
print column
1011
Ending
print column

The attribute byte-(M)

= ll(decimal)

for our flask character.

You’ll probably recognize ml . ..mll from the top of our

layout grid. That’s right, each column is described by one byte.
Now we’ve got everything we need to download one character
to the printer. The complete command for our flask character is
shown below:

CHR$(27);CHR$(38);CHR$(O);CHR$(GO);CHR$(6O);CHR$(l39)
;CHR$(2);CHR$(5);CHR$(8);CHR$(241);CHR$(O);CHR$(O)
;CHR$(241);CHR$@);CHR$(5);CHR$(2);CHR$(O)

Now let’s send the information to the printer. The following

program will send the character definitions for all three
characters to the printer. Turn off the printer and set DIP
switch 2-l off. Then turn on the printer. Enter the program and
run it.

10 LCRINT CHR$(27);"&";CHR$(O);CHR$(60);CHR$(62);
20 FOR N=60 TO 62
30 FOR M=O TO 11
40 READ MM
50 LPRINT CHR$(MM);
60 NEXT M
70 NEXT N
80 LPRINT
90 END
100 DATA 139, 2, 5, 8,241, 0, 0,241, 8, 5,
2, 0
110 DATA 139,124, 0, 66, 4, 64, 36, 16, 2, 16,
12, 0
120 "@A 139, 46, 16, 2, 60, 0, 48, 0, 48, 0,
9 0

When you run this program, it looks like nothing happens.

That’s OK. We’ll see why in just a moment. Save this program.
We’ll need it again shortly.
I

PRINTING DOWNLOAD CHARACTERS

You’ve now defined and sent three characters to your printer.

But how do you know that? If you try printing those characters
now you don’t get a flask, car and gun. Instead you get . . ( = ).
That’s because the download characters are stored in a different
part of the printer’s memory. To tell it to look in download
character RAM instead of standard character ROM it requires
another command:

(ESC)“%“CHR$(n);CHR$(O)

This command is used to select the download character set (if

n=49) or to select the standard character set (if n =48). Let’s
try it out. Enter this program:

10 LPRINT CHR$(27>;"%1";CHR$(O);
20 LPRINT CHR$(6O>;CHR$(61>;CHR$(62)
30 LPRINT CHR$(27>;"%O";CHR$(O)
40 END

Voila! It should have printed out the three characters we defin-

ed. Your printout should look like this:

(If it doesn’t, check the last program we ran for errors, then
rerun it.)

Let’s find out if there are any other characters in the

download RAM. Try this program:

10 LPRINT CHR$(27);"%1";CHR$(O)
20 FOR I=32 TO 126
2; ;;X";N; U-W(I);

50 LPRINT
60 FOR I=160 TO 254
'7; g;;"; CHR$(I);

90 LPRINT
100 LPRINT CHR$(27);"%O";CHR$(O)
110 END
92

Nope! Just three characters in the download set. This is incon-

venient for a couple of reasons. First, every time you wanted to
use a download character you would have to switch back and
forth between character sets. Knowing that you wouldn’t want
to do that, your printer won’t even allow it. So we have made it
an easy task to use mostly standard characters with just a few
special characters thrown in. This command copies all the
ASCII characters from the standard character ROM into
download RAM:

(ESC)“:“CHR$(O);CHR$(O);CHR$(O)

Since it will copy all characters into download area, it will

wipe out any characters that are already there. So it’s important
to send this command to the printer before you send any
download characters you want to define. With that in mind, add
this line to the program we used to send the characters to your
printer:

5 LPRINT CHR$(27);":"; CHR$(O);CHR$(O);CHR$(O)

Now try the download printout test program again. Your

results look like Figure 6-11.

Figure 6- 11. Printout of the dqwnload character set, into which all
the ASCII characters have been copied, and the (, = and > have been
changed.

To demonstrate how to use these characters, let’s use this

character set to print a small graph. This program, which has
been built around the first program in this chapter, will do just
that:

10 LPRINT CHR$(27);":"; CHR$(O);CHR$(O);CHR$(O);

20 LPRINT CHR$(2~>;"&";CHR$(O);CHR$(6O);CHR$(62);
30 FOR N=60 TO 62
40 FOR M=O TO 11
50 READ MM
60 LPRINT CHR$(MM);
93

70 NEXT M
80 NEXT N
90 LPRINT
100 DATA 139, 2, 5, 8,241, 0, 0,241,
8, 5, 2, 0
110 DATA 139,124, 0, 66, 4, 64, 36, 16,
16 12
120 DA% 139: 46: 160, 2, 60, 0, 48, 0,

130 L%NT"~H~~~27;~"D"-cHR$(ll)CHR$(0)
140 LPRINT CHR$(27)f"h";CHR$(l);'
150 LPRINT " U.S. EXPORTS"
160 LPRINT cHR$(27>;"h";c~~$(o);
170 LPRINT CHR$(27);"~l";CHR$(O);
180 LPRINT "AUTOS";CHR$(9);
190 FOR I=.4 TO 9.3 STEP .4
200 LPRINT CHR$(61);
210 NEXT I
220 LPRINT
230 LPRINT "CHEMICALS";CHR$(g);
240 FOR I=.4 TO 8.7 STEP .4
250 LPRINT cHR$(So);
260 NEXT I
270 LPRINT
280 LPRINT "GUNS";CHR$(g);
290 FOR I=.4 TO 1.4 STEP .4
300 LPRINT CHR$(62).;
310 NEXT I
320 LPRINT
330 LPRINT CHR$(g);"+--";
340 SCALE$=“--+--‘I
350 FOR I=2 TO 8 STEP 2
360 LPRINT SCALE$;
370 NEXT ‘I
380 LPRINT "--+"
390 LPRINT CHR$(9);" ";
400 FOR I=2 TO 8 STEP 2
410 LPRINT " ";I;
420 NEXT I
430 LPRINT CHR$(27);"$O";CHR$(O)
440. LPRINT CHR$(27);"SO";
450 LPRINT CHR$(9);"MILLIONS OF DOLLARS"
460 LPRINT cH~$(27);"~"
470 END
94

Note that we didn’t have to re-enter the download characters,

since they were already sent to the printer with the first pro-
gram. They will stay with the printer until you download new
characters to replace them or turn the printer off. Even the
(ESC) “a” command, which initializes the printer, does not
destroy the contents of download RAM.

DEFINING PROPORTIONAL CHARACTERS

Except for the actual width, defining characters for propor-

tinal printing is exactly the same as defining normal width
download characters. Characters can range from 5 to 11 dots
wide. This means that characters can be as narrow as one-half
the normal width.
Besides being able to specify the actual width of the
character, this printer allows you to specify the position in the
standard grid where the character will print. You must specify
the dot column in which the printed character starts and the dot
column in which the character ends. Why, you may ask, would
you want to define a character this way instead of merely defin- - -
ing the overall width of the character? Because this printer’s pro-
portional character definitions can also be used to print normal
width characters, which are eleven dot columns wide. And by
centering even the narrow characters in the complete grid they
will look good even when you aren’t printing them proportional-
ly.
. The command format for proportional character definition is
exactly the same as you have learned; the only difference is the
attribute byte, m0. As you know,the first bit of m0 is used to
specify whether the character is descender or not. The next -
three bits are used to specify the starting print column (accep-
table values are 0 to 7). The last four bits specify the ending -
print column (acceptable values are 4 to 11). The minimum
-
95

character width is five dots (so you could not, for instance,
specify a starting column of 6 and an ending column of 8, even
though those are both within the acceptable range). If you in-
advertantly give an incorrect width value, however, your printer
is forgiving: it will automatically revert to the default width of
eleven dot columns.
Just as there was an easy trick for figuring the attribute byte
earlier, you still don’t need to know a thing about binary
arithmetic. Merely multiply the starting column by 16, add the
ending coulmn number, and add 128 if the character is not a
descender. If you prefer a formula: (descender * 128)+(start *
16)+ end.
One thing to remember about defining proportional
characters: a character cannot be wider than the specified
width. That seems obvious enough! For example, if you specify
a width of 6 for a character (starting in column 1 and ending in
column 6), the seventh through eleventh of dots (if you specified
any) will not print. You must, however, send information (even
if it is 0) for those columns when you defined a character; your
printer expects eleven characters following the (ESC)“&”
CHR$(O) nl n2 m0 sequence.
In most cases, the width you select should actually be one dot
wider than the number of columns that the character actually oc-
cupies. This is so that there will be a space (of one dot) between
3 characters when you print them. If you specify a width which is
exactly the same as the number of columns in the character
definition, the characters will touch when they print (this is
sometimes desirable - for border characters or for large
download characters that are more than eleven dots wide).

DEFINING NLQ DOWNLOAD CHARACTERS

In the previous sections, we have learned how to define and

print the draft download characters.
As you’ve learned in Chapter 3, you can print NLQ
characters. You can also define the download characters with
NLQ mode. Since NLQ characters use many more dots than
draft characters, defining NLQ download characters is more
complex than designing draft ones. If you use the grid and the
program in this section, however, you will be able to design your
own NLQ characters.
96

Because the NLQ characters can use as many as 16 dots ver-

tically and 11 dots horizontally, you plan your designs on a dif-
ferent grid than the one you used for draft characters. Make up
some grids (photocopy Figure 6-12 if you wish) and get ready to
be creative!

128
128
84
ASCII Code:
64
32 Descender:
32
16 Start column:
16
8
End column:
8
4
4
II
MO = Descender * 128 + (Start * 16 ) + End

2
2
1
1
TOtd
1st
2nd

Figure 6-12. Use this grid (or one similar to it) to define your own
NLQ characters.

As you noticed when the NLQ characters are printed, they are
printing in twice; the first line of data is printed, the paper is
moved up a distance of l/2 dot, then the second data line is
printed. So, we’ve written the numbers on the horizontal lines.
To calculate the data numbers for this column, you see which
dots are used in the box and add their values together. Then you
go down the dots on the horizontal lines and add their values
together as shown in Figure 6-13.

Now we’ll show you how to use the NLQ character definition
with a flask as shown in Figure 6-13. Figure 6-13 shows the
design drawn on a grid and the data numbers printed at the
bottom of each column.
If you look at each column individually, you can see how the
data numbers were calculated.
97

ASCII Code: ($0

Descender: 2.

Start column:

End column:

MO = Descender* 128 + (Start * 16 ) + End

Figure 6- 13. Add the values of the dots in each box and line col-
umn and write the sum of each column at the bottom.

Now enter the following program and run it. It has the data
numbers for the NLQ flask character. For a character of your
own, change the DATA numbers and the character definition
$osition.

10 LPRINT ~~~$(27)pXl";
20 LPRINT CHR$(27);"&";CHR$(O>;CHR$(6O);CHR$(6O);
30 FOR M=O TO 22
40 READ MM
2; ;;;;"; CHR$(MM) ;

70 LPRINT
80 LPRINT CHR$(27);"xO"
90 END
100 DATA 139, 2, 5, 8,241, 0, 0,241, 8,
5, 2, 0
110 DATA 6, 8, 16,224, 0, 0,224, 16, 8,
6, o
120 DATA 139,124, 0, 66, 4, 64, 36, 16, 2,
16, 12, o
130 DATA 120, 4, 0, 4, 0, 96, 4, 0, 4,
8, 0
140 DATA 139, 46, 16, 2, 60, 0, 48, 0, 48,
o, 48, o
150 DATA 92, 32, 4, 60, 0, 48, 0, 48, 0,
48, 0

When you want to print the defined character, you must select
the NLQ mode first, then select the download characters. If you
don’t select the NLQ mode, the download characters are not
printed even you selected the download character set.
To demonstrate how to use the NLQ download characters,
let’s use this character set to print a small graph. Try this pro-
gram.

10 LPRINT CHR$(27
20 LPRINT CHR$(27 ;CHR$(O);CHR$(O);
30 LPRINT CHR$(27 ;cHR$(60);CHR$(62 );
40 FOR N=60 TO 62
50 FOR M=O TO 22
60 READ MM
7’; i;;;N; CHR$(MM);

90 NEXT N
100 EPRINT
110 DATA 139, 2, 5, 8,241, 0, 0,241, 8,
5, 2, 0
120 DATA 6, 8, 16,224, 0, 0,224, 16, 8,
.-
6, 0 .
130 DATA 139,124, 0, 6.6, 4, 64, 36, 16, 2,
16, 12, o
140 DATA 120, 4, 0, 4, 0, 96, 4, 0, 4,
8, 0
150 D;TA4;39, 46, 16, 2, 60, 0, 48, 0, 48,
0
160 DA{A 42, 32, 4, 60, o, 48, 0, 48, o,
48
i70 LP;IN; CHR$(27);"D"*CHR$(ll)~CHR$(O)
180 LPRINT CHR$(27);"h";CHR$(l);'
190 LPRINT ' U.S. EXPORTS"
200 LPRINT CHR$(27>;"h";CHR$(O>;
210 LPRINT CHR$(27);"%l";CHR$(O);
220 LPRINT "AUTOS";CHR$(9); -
230 FOR I=.4 TO 9.3 STEP .4
99

240 LPRINT CHR$(61);

250 NEXT I
260 LPRINT
270 LPRINT "CHEMICALS";CHR$(g);
280 FOR I=.4 TO 8.7 STEP .4
290 LPRINT CHR$(60)
300 NEXT I
310 LPRINT
320 LPRINT "GUNS";CHR$(g);
330 FOR I=.4 TO 1.4 STEP .4
340 LPRINT CHR$(62);
350 NEXT I
360 LPRINT
370 LPRINT CHR$(g);"+--";
380 SCALE$=~--+--~~
390 FOR I=2 TO 8 STEP 2
400 LPRINT SCALE$;
410 NEXT I
420 LPRINT"--+"
430 LPRINT CHR$(g);" ";
440 FOR I=2 TO 8 STEP 2
450 LPRINT " ";I;
460 NEXT I
470 LPRINT CHR$(27>;"%O";CHR$(O)
480 LPRINT CHR$(27);"SO";
490 LPRINT CHR$(9); "MILLIONS OF DOLLARS"'
500 LPRINT CHR$(27);"T"
510 END
100

MEMO

-
CHAPTER 7

DOT GRAPHICS

Subjects we’ll cover in Chapter 7 include-

. This printer’s bit image graphics capabilities;
l Printing a pre-defined shape;
l Plotting a calcurated shape;

l High-resolution graphics.

In Chapter 6 you were introduced to a form of computer

graphics; you were able to actually define characters dot by dot.
In this chapter you’ll learn to use the same principles to make
your printer print whole pages of dot graphics! We’ll show you
how to use dot graphics to create “super download characters”.
In addition, you’ll see how your printer can be used as a
graphics plotter. This can have some practical business applica-
tions as well as create some terrific computer art!

COMPARING DOT GRAPHICS WITH DOWNLOAD

CHARACTERS

A good understanding of dot graphics requires an understand-

ing of how dot matrix printers work; you may want to review
the first few pages in Chapter 6. The principles for dot graphics
are the same as those for download characters.
There are some differences in the way they are implemented
however. While download commands can be used to define a
character between four and eleven columns of dots wide, dot
graphics commands can be used to define a shape as narrow as
one column of dots wide or as wide as 1920 dots!
There is no “descender data” with dot graphics; graphics im-
ages are always printed with the top seven or eight pins of the
print head, depending on whether you have a 7-bit or &bit inter-
face.
So when do you use graphics and when do you use download
characters? Practically anything you can do with graphics you
can do with download characters, and vice versa. A clever pro-
grammer could actually plot a mathematical curve using
download characters or use strings of graphics data as user-
defined characters. But why do it the hard way? There are
several instances when dot graphics is clearly the best way to ap-
proach the problem:
lIf the graphics image to be printed is wider than 11 dots or
higher than 8 dots.
@If an image is to be printed just one time, as opposed to a
frequently used “text” character.
*If you want higher resolution (this printer can print as
many as 240 dots per inch in dot graphics mode; text mode,
which includes download characters, prints 60 dots per
inch .)

USING THE DOT GRAPHICS COMMANDS

The command to print normal density (60 dots per inch

horizontal; 72 dots per inch vertical) dot graphics uses this for-
mat:

(ESC,)“*“CHR$(O) nl n2 ml m2 ...

Just like many of the other codes you have learned, the com-
mand starts with an escape sequence ((ES,>“*” in this case).
This is followed by CHR$(O), which specifies normal density
(the other densities are described later in this chapter). But
unlike the other codes there can be any number of graphics data
bytes following the command. That’s where nl and n2 come in;
they are used to tell the printer how many bytes of graphics data
to expect.

m Specifying the number of columns of dots

To figure the values of nl and n2, you’ll need to figure out
how wide your graphics image will be (remember that there are
60 columns of dots per inch in normal density). Then comes the
fun part: converting one number (the number of columns of
dots) into two! Why is it necessary to use two numbers to tell the
printer the number of graphics codes to expect? Because the
largest number we can send in one byte (that’s what the BASIC
CHR$( ) function sends: one byte) is 255. And with the normal
density graphics it’s possible to have a graphics image as wide
as 480 dots. So to figure out how many columns of graphics data
to expect, your printer multiplies n2 by 256 and adds the value
of nl to the product. If you divide the number of columns by
256, then n2 is the quotient and nl is the remainder (why not let
your computer figure it out for you: if the number of columns is
assigned to variable X, then nl =X MOD 256 and
nZ=INT(X/256)). Table 7-l might make things even easier.

Table 7-1
Calculating nl and n2.
kf the numb

1024 to 1279 1 x-1024 4

I ILO” L” IJ3.J I x-1280 5
t 1536 to 1791 I x-15 ?G
V” I
G
innn L- 1920 1 x-1792 ;

n Specifying the graphics data

Now that we’ve told the printer how much data to expect, we
better figure out how to send that information! Just as you do
with download characters, with dot graphics you have control
over the firing of every single pin on the print head. In Figure 7-
1, you can see that we’ve. labelled each pin on the print head
with a number, as we did with download characters. And speci-
fying pins to fire is done in the same way: to fire the second pin
from the top, for instance, send a CHR$(64). Firing several pins
at once is done in a similar fashion. For example, to print the
first, third, and fourth dots, add their values (128 + 32 + 16) to
send this total: CHR$(176). This is one byte of graphics data; it
would replace ml in our format statement.
1
Figure 7- 1. Starting with the most significant bit at the top, each
J
pin of the print head is assigned a value which is a power of two.

A short program should demonstrate how to implement the

graphics command. The program below gave us this printout:

__----._._ ___““““--....” _-_,

-- ______._ --.

10 i Demo of dot graphics

20 PI=3.14159
30 WID=lOO
40 OPEN "LPTl:" AS #l : WIDTH #1,255
50 PRINT#l, CHR$(27);"H";CHR$(0);
60 PRINT#l, CHR$(WID MOD 256);
70 PRINT#l, CHR$(INT(WID/256));
80 FOR I=0 TO WID-1
90 J=l+SIN(I"PI/32)
100 PRINT#l, CHR$(2*INT(J*3.5+.5
110 NEXT I
120 LPRINT
230 CLOSEXl

In lines 50 to 70, we’ve selected normal density graphics and

said that 100 characters of graphics data would follow. The loop
between lines 80 and 110 is repeated to plot 100 points along a
curve. This is an example of plotting a very simple
105

mathematical function (a sine wave) to create a design. Later in

this chapter we’ll show something more complex. The
mathematical concepts (such as sine and pi) demonstrated here
are not important; you don’t have to be a math whiz to use this
printer’s graphics.

n Combining text and graphics

It’s also possible to mix text and graphics in one line. This can
be useful for labeling charts or graphs, or even inserting fancy
graphics in text. Try adding these lines to our program:

45 PRINTUnl, "WOW' ";

115 PRINT#l, "THiS IS GREAT! ";

Now if you run the program you should get a printout that
looks like this:

14 (1;)bJ ! ._--“-----___ _....----.-- _.,, “I_ t.,, 1 cz; I[ cr; (1; R /g,-(- !
“..... .........-“’

But there is one thing to be careful of: all graphics data must
print on the same line. The graphics command is turned off at
the end of each line, even if you have specified that more
graphics codes follow. To see what we mean, change line 30 to
plot 1000 points and run the program.

30 WID=lOOO

wciw ’ --.--
TH I s 1s ‘eEflTT--------.---

This will make the sine wave pattern long enough to go off the
page.
As you can see, your printer printed graphics up to the end of
the line, then ignored the rest of the graphics data and returned
to normal text on the next line.
106

PRINTING A DESIGN OR LOGO

Since you control the firing of every pin, you can print nearly
anything with your printer that can draw (and probably better, if
you’re like most computer users!). You can be used for creating
“computer art” or drawing maps. Or, as we’ll show you here,
you can use dot graphics to print your logo at the top of each let-
ter you print.
Designing an image to print with dot graphics is much like
designing download characters. The best way to start is to lay
out your image on graph paper. Since you can print eight rows
(seven with a 7-bit interface) of dots with each pass of the print
head, draw a heavy horizontal line every eight rows on your
graph paper. And it may be helpful to write the dot values
(128,64,32, etc.) down the left side of each row. Then after
you’ve filled in the “dots” that you want to print, it’s time to get
out the old calculator again! Just as you did with download
characters, add up the values of each column of dots; this makes
up one byte.

!
! s&s
-- ~--~~~~~ ~~~~~~ _J
Figure 7-2. By laying out the logo on graph paper, you can
calculate all of the graphics data.
107

In the program below, we’ve taken the logo graphics informa-

tion and put it into BASIC DATA statements. The program
itself is short and simple. The loop starting at line 100 reads the
data statements into a string array variable called LOGO$. In
line 170 we change the line spacing to 8/72 inch so that the lines
of graphics data will connect vertically. The actual printing is
done in the loop between lines 180 and 210; line 190 sends the
graphics control code to the printer and line 200 sends one line
of graphics data.
The printout from the program is shown right below the pro-
gram.

10 1 Prints S&S logo

20 LINE.8$=CHR$(27)+"A"+CHR$(8)
30 f Set line spacing to l/6”
40 LINE.l2$=CHR$(27)+"2"
1 Select dot graphics
2: GRAPHIC$=CHR$(27)+CHR$(42)+CHR$(O)
70 DIM LOG0$(4)
80 WIDTH "LPT1:",255
90 1 Read data
100 FOR ROW=1 TO 4
110 FOR COLUi"DJ=lTO 100
120 READ P
130 LOGO$(ROW)=LOGO$(ROW)+CHR$(P)
140 NEXT COLUMN
150 NEXT ROW
160 f Print logo
170 LPRINT LINE.8$;
180 FOR ROW=1 TO 4
190 LPRINT GRAPHIC$;CHR$(lOO);CHR$(O);
200 LPRINT LOGO$(ROW)
210 NEXT ROW
220 LPRINT LINE.12$
230 ' Row 1
240 DATA 0 0 01 7, 15
250 DATA 1:; 14: 14; 14: 14; 73: ;; ;I 3, 15
260 DATA 15, 15, o, o, o, o, o, o, o, o
270 DATA 0, 1, 3, 3, 7, 7, 15, 14, 14, 14
280 DATA 14, 15, 7, 7, 7, 3, o, o, o, o
290 DATA 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
300 DATA 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
310 DATA 0, 0, 0, 0, 1, 3, 7, 7, 7, 15
320 DATA 14, 14, 14, 14, 14, 7, 7, 3, 3, 15
330 DATA 15, 15, 0, 0, 0, 0, 0, 0, 0, 0
340 ' Row 2
350 DATA 0, 60,255,255,255,255,255,143, 15
360 DATA
370 DATA

400 DATA 31, 31, 15, 7, 3, o, o, o, ;, ;

410 DATA 0, 0, 0, 0, 0, 0, 0, c,
420 DATA 0, 0, 60,255,255,255,255,255,143: 15
430 DATA 24;;24;: 7, 7, 3, 3, 3,131,193,241
440 DATA 0, 0, 0, 0, 0, 0, 0, 0
450 ' Row 3
460 DATA 0, 31, 31, 3,12g,128,1g2,192,1g2,lg2
470 DATA 192,224,224,224,224,240,255,255,255,255
480 DATA 255,127, o, o, 0, 0, 63,127,255,255
490 DATA 255,255,193,128,128,128,128,lg2,224,24o
500 DATA 252,255,255,255,127, 63, 31, 7, 7, 31
510 DATA 254,252,248,224,128, 0, 0, 3, 7, 7
520 DATA 7, 3, 0, 0, 0, 0, 0, 0, 0, 0
530 DATA 0, 31, 31, 3,129,128,192,192,192,192
540 DATA 192,224,224,224,224,240,255,255,255,255
z5-i yA;;,2;5,"7, 0, 0, 0, 0, 0, 0, 0, 0
570 DATA 0,248,248,240,224,224,112,112, 56, 56
580 DATA 56, 56, 56,120,12o,24o,240,;24,224,lg2
590 DATA 128, 0, 0, 0, 0, o,L?2,Z24,240,240
600 DATA 240,248,248,248,120,120, 56, 56, 56, 56
610'DATA 48,112,224,224,224,224,24&240,248,248
620 DATA 120,120, 56, 56, 56, 56,120,240,224,224
630 DATA 192,128, 0, 0, 0, 0, 0, 0, 0, 0
640 DATA 0,248,248,240,224,224,112,112, 56, 56
650 DATA 56, 56, 56,12o,l2o,24o,24o,224,224,lg2
660 DATA 128, 0, 0, ,O, 0, 0, 0, 0, 0, 0

If you are using with the IBM mode (DIP switch l-6 off), _
change the following lines to the program given above.
-
109

20 LINE.8$=CHR$(27)+CHR$(65)+CHR$(8)+CHR$(27)+
CHR$(5Oj
40 LINE.l2$=CHR$(27>+CHR$(65)+CHR$(l2)tCHR$(27)t
CHEI$(50)

PLOTTING WITH YOUR PRINTER

This section of the manual gets into more serious BASIC pro-
gramming just because it’s required in order to have the com-
puter act as a plotter driver. Don’t be intimidated; while it’s
beyond the scope of this manual to teach BASIC, if you try the
examples and take it slowly you should be doing some fancy plot-
ting of your own before you know it.
If designing and calculating dot graphics images by laying
them out on graph paper seems too tedious to you, then let the
computer do the work for you! With your computer doing the
calculations and your printer plotting the output, you can come
up with some terrific business graphs, charts, and mathematical
function plots.
The best way to do this is to set up an array in memory. This
is your “graph paper.” The first thing to do is to determine how
big you want your output to be; this will determine the size of
your array. (If you have grandiose plans to fill an entire page
with plotter output, you better have lots of memory in your com-
puter. With 60 dots per inch horizontally and 72 dots per inch
vertically, it takes at least 540 bytes of memory for each square
inch of plotted area. That doesn’t sound so bad - but an area 8
inches square requires over 32K!)
Your array should be two-dimensional (just like graph paper)
where one dimension will be the number of columns of dots and
the other dimension is the number of printing lines (remember
that you can have up to eight rows of dots per printed line).
Here’s a program that will use calculated-shape graphics to
plot a circle. As you’ll see, by changing a few lines it can be used
to plot virtually any shape.

10 1 Plotting program
20 1 Set program constants
30 MAXCOL%=75 : MAXROW%=
40 DIM BIT%(MAXCOL%,MAXROW%)
50 MASK%(l)=64 : MASK%(4)=8
60 MASK%(2)=32 : MASK%(5)=4
70 MASK%(3)=16 : MASK%(6)=2
80 LX=~O : LY=20
90 LXFAC=72/LX : LYFAC=~'~'/LY
100 1 Plot curve
110 GOSUB 600
120 1
130 1 Send bit image map to printer
140 LPRINT CHR$(27);"A";CHR$(6);
150 FOR ROW%=0 TO MAXROW%
160 A$=""
170 LPRINT CHR$(27) ;"*";CHR$(O);CHR$(MAXCOL%);
CHR$(O) ;
180 FOR COL%=l TO MAXCOL%
190 A$=A$+CHR$(BIT%(COL%,ROW%))
200 NEXT COL%
210 LPRINT A$;" It
220 NEXT ROW%
230 LPRINT CHR$(27>;"A";CHR$(l2);
240 END
250 1

260 ) Subroutine to draw a line from Xl,Yl to

X2,Y2
270 I
280 XL=X2-Xl : YL=Y2-Yl
290 NX=ABS(XL*LXFAC) : NY=ABS(YL*LYFAC)
300 IF NX < NY THEN NX=NY
310 NS$=INT(NX+l)
320 DX=XL/NS% : DY=YL/NS%
'FOR I%=1 TO NS%
it: Xl-Xl+DX : Yl=Yl+DY
GOSUB 400
;zi NEXT 1%
RETURN -
2: I
410 1 Subroutine to plot a point at Xl,Yl
420
430 XX=Xl"LXFAC : YY=Yl"LYFAC
440 COL%=INT(XX)+l
450 ROW%=INT(YY/6)
460 XIT%=INT(YY-ROW%s6)+l
.470 BIT%(COL%,ROW%)=BIT%(COL%,ROW%) OR MASK%(XIT%)
480 RETURN
600 ?
610 ( Subroutine to plot a circle
620 !
630 RAD=9
640 x1=19 : Yl=lO -
650 FOR ANG%=O To 360 STEP 10
660 RANG=ANG%*6 28/360
670 X2=RAD"COS(iANG)tlO : Y2=RADSSIN(RANG)tlO
680 GOSUB 250
690 NEXT ANG%
700 RETURN

If you are using with the IBM mode (DIP switch 1-6 off),
change the following lines to the program given above.

140 LPRINT CHR$(27>;"A";CHR$(6);CHR$(27);"2"

230 LPRINT CHR$(27);"A";CHR$(l2);CHR$(27);"2'+

n How the program works

In the program above, we’ve created an array called BIT%,
which is dimensioned in line 40. You’ll note that instead of using
numeric constants to dimension the array, we used the variables
<MAXCOL% and MAXROW%. This way, if your computer has
enough memory and you want to plot a larger image, all you
need to change are the values in line 30. The array MASK% con-
tains the values of the dots. (In order to make this program run
on most computers, we’re only six pins for graphics. With many
computers, you can use all eight available pins.) In lines 80 and
90 we’ve defined some other variables you’ll be interested in:
LX, LXFAC, LY, and LYFAC are used as scaling factors. By
changing these values, you can change the size of your printed
image or even distort it (you can, for example, make our circle
print as an ellipse). Experiment a little bit!
The main calculations for plotting the image are done in the
subroutine starting at program line 600. This is where you put
the formulas that you want to plot. By changing just the lines
after 600 (with some creative mathematics!) you can plot any
function - limited only by your imagination. Some examples
are shown at the end of this section.
What the program section starting at line 600 actually does is
112

tocalculate starting and ending points for a line (in our circle the
“lines” are very short - sometimes the starting and ending
points are the same). The coordinates of the starting point of the
line are assigned to variables Xl and Y 1. The line ends at point
X2, Y2. When these coordinates have been calculated, a
subroutine call is made to line 250. This subroutine calculates
the coordinates of individual points along that line.
After these coordinates have been determined, the subroutine
at line 400 is called. This routine turns “on” an individual dot in
our array called BIT%. (Keep in mind that no printing has been
done yet; the computer is still drawing the image on its “graph
paper” in memory.) The way an individual dot is turned on is us-
ing the logical OR function in line 470.

When all the points have been plotted in memory, printing

begins at line 130. We first set the line spacing to 6/72 inch us-
ing the (ESC)“A”CHR$( n ) command. This is so that there are
no gaps between rows of dots. Then the loop from line 150 to
line 220 prints the dot graphics image one line (which is six dots
high) at a time. The variable A$ is used to build a string of all
the columns of BIT% in a given row.
As you can see, by taking the program in small pieces and
analyzing it, graphics programming does not have to be dif-
ficult. If you want to try some other plots, try these (replace
lines after 600 with the lines below). The printouts from each
program are shown below the listing.

600 '
610 ' Subroutine to plo,t a star
620 1
630 RAD=9
640 FOR ANG%=O TO 360 STEP 45
650 RANG=ANG%*3.14159/180
660 RANG2=(ANG%+l35)*3.14159/180
670 Xl=RAD*COS(RANG)tlO
680 Yl=RAD*SIN(RANG)+lO
6go X2=RAD*COS(RANG2)+10
700 Y2=RAD*SIN(RANG2)+10
710 GOSUB 250
720 NEXT ANG$
730 RETURN
I
113

600 ’
610 ) Subroutine to plot a sine wave
620 )
630 x1=0 : Yl=lo : x2=20 : Y2=10
640 GOSUB 250
650 x1=10 : Y~=O : x2=10 : Y2=20
650 GOSUB 250
670 X1=0 : Yl=lO
680 FOR X2=0 TO 20 STEP .2
6go Y2=lO-g"SIN(3.ltil59~X2/10)
700 GOSUB 250
710 NEXT X2
720 RETURN

HIGH RESOLUTION GRAPHICS

Up until now all of the dot graphics printing we have done has
been with your printer’s normal density mode. This can give
you some pretty sharp images at great speed. Sometimes
though, you may want to create an image with even higher
resolution. This printer has seven graphics modes you can use;
they’re summarized in Table 7-2.
. ..

114

Table 7-2
Dot graphics commands

Function I Control code

Normal densitv (60 dots/inch) 1 (ESC)“*“CI HR$(O) nl n2 ml m2 . ..
Double densit; (120\_-_ dotdinch~
--_- ._.. -.., 1(:ESC)“*“CfiR$(l) nl n2 ml m2
,/double weed
Doubledensity.---.--. ~_~~~ 1, (ESC
j )“*“CHR$(2) nl n2 ml m2
1 Quadrunle densitv (240 dots/inch)/ (ESC) “*“CHR$(3) nl
---- I
n2 ml m2 ...
CRT graphics (86 dots/inch) (ESC)“*“CI HR$(4) nl n2 ml m2 ...
Plotter graphics (72 dots/inch) (ESC)“*“CHR$(5) nl n2 ml m2 ...
CRT graphics type II (90 dots/inch) (ESC)“*“CHR$(G) nl x2 ml m2 ..?

The command syntax for all of the commands is the same -

just as you have learned it for the (ESC)“*“CHR$(O) (normal
density) command. The number of columns to be printed is nl
+ 256 * n2.
So what do these different modes do? On the following pages
are actual size reproductions of printouts of the same image
printed in each of the seven different graphics modes. They
were all printed using the plotting program in this chapter (with
a rather complex set of formulas starting at line 600!).

Normal density graphics

115

Double density graphics

Double density/double speed

So if quadruple density looks so great, why not use it all the
time? Let’s try an experiment on your printer which will show
just how the different modes work. Using the first program in
this chapter, change line 50 to try each of the different modes.
Just change the “0” to “l”, “2”, “3”, etc. in turn. Your printouts
should look something like this:

.---; ---Z-. =----.,

(ESC) “*” CHR$( 1)

,,, - -.... _ .. . ...,

,, ‘.

(ESC) “*” CHR$(2)

,-...,.n
(ESC) I‘*” CHR$(3)

_-------.
-- ---- ----...._-----

(ESC) “*” CHR$(4)

m__=--__
‘--._ _--

(ESC) “*” CHR$(S)

_----- ___ _--

__-- -- -_
(ESC) “*” CHR$(6)

As you can see, the different modes seem to condense the

printed image. So, to get the same image in a higher density
mode, you must plot more points. This requires twice as much
memory for your array, twice as much computing time, and
twice as much printing time (but the results may be wirth it!).

Our engineers have given programmers a unique shortcut for

program development - double density double speed graphics.
Although this mode requires just as much memory and com-
- 119

puting time as double density, it prints at the same speed as nor-

mal density graphics. Amazing, you say? Well, it is - until you
know the secret. Every other column of dots is ignored, so the
output is actually the same as normal density graphics. The ad-
vantage is that you can write and debug your programs at dou-
ble speed, then change to double density graphics for terrific out-
put.
This printer has three other densities (CRT, plotter, and CRT
type II ) which can be used to achieve greater compatibility with
various hardware and software configurations. Plotter density
can be especially for simplifying programming, since it has
equal densities both the horizontal and vertical directions (72
dots per inch each way). With this feature you can plot truely
round circles without any type of scaling factors.

COMPATIBJLITY WITH EXISTING SOFTWARE

With its ability to print seven different graphics densities, this

printer’s graphics abilities are advanced indeed. There are
many programs, in fact, that are unable to use this printer’s
single graphics command (ESC)“*” for selecting the proper
density. To maintain compatibility with this software, there are
individual commands to select each of this printer’s common

Table 7-3
Alternative graphics commands
Density Single command Individualcommand
(ESC)“*” CHWW) ~1 n2 (ESC)<<K,, lzl n2ml m2 ...
Normal
ml m2 . . .
(ES(I)“*”
Double CHR$(l) ” x2? (ESC)“L” nl nZ ml m2 . . .
ml m.2 . . .
Double with (ESC)“*” CHR$(2) nl n2 xESC)“Y,, nl n2 ml m2
...
double-speed ml m2 . . .
(ES(Z)“*” CHR$(3) nl n2
Quadruple (ESC)“Z” nl 722ml m2 . . .
ml m2 . . .
(ES(Z)“*” CHR$(4) nl n2 none
CRT
ml m2 . . .
(ES(I)“*” CHR$(5) nl 722 nOne
Plotter
ml m2 . . .
(ES(X)“*” CHRW) ~1 ~2 nOne
CRT type II ml m2 . ..
,

120

graphics densities. These commands, which are shown in Table

7-3, can be used interchangeably with the corresponding (ESC)
“*” command. Like the commands you are already familiar
with, these new commands are followed by two bytes to specify
the number of graphics data bytes to print and then the data.

MORE GRAPHICS PROGRAMMING 1 IPS

At the end of this chapter, we’ll discuss two modes that the
printer offers to help you solve potential graphics problems. A
redefining code allows you to change the density for graphics
programs that use one of the four alternate codes. The g-pin
graphics mode allows you to use all nine pins on each line and
thus speed up screen dumps.

Table 7-4
More graphics commands
Function Control code
Redefine the graphics mode (ESC)“?” n0 nl
(ESC)” - ” CHR$(nO) nl n2
g-pin graphics
ml m2

n Redefining alternate graphics codes

Your printer provides a command to redefine one of the alter-
nate graphics modes - K, L, Y, or 2 - so that it represents any
other of the seven graphics modes. The command is (ESC) “?”
n0 nl, where n0 is one of the four letters, “K”, “L”, “Y”, or “Z”,
and nl is one of the numbers used with the (ESC) “*” corn-
mand, 0 to 7. There are several instances in which you may use
this sequence.
The first occurs if you have written a program to be printed in
one graphics mode and now want to print it in another. If you
have used concatenation to store your graphics command in one
_short character string, that will not be difficult. You can simply
change the mode number or alternate code in the definition of
the character string.
A second time you can make good use of the redefining code
occurs when you want to change a program in which you have
not concatenated the graphics codes. Using the (ESC) ‘?” se-
quence allows you to change every instance of your graphics
command by entering only one line.
121

n g-pin graphics mode

In the early part of this chapter, we said that the bottom pin of
the print head is not normally used in the graphics modes.
That’s because most computers communicate with parallel-type
peripheral devices using eight data lines. When the peripheral is
a printer, each data line corresponds to one pin on the print
head. Thus each byte sent will fire up to eight pins.
But the printer has 9 pins available. So how do you fire the
ninth pin with only 8 data lines? In fact, do you really want to
bother with just one extra pin? Well, for such graphics-intensive
applications as screen dumps, printing 9 pins at a time can
speed up the process considerably. For this purpose, your
printer has a special g-pin graphics mode (it won’t, however,
work with 7-bit interface systems). In this mode the printer
takes 2 bytes to fire all 9 pins as shown in Figure 7-3.

128
64
32
16
First byte
8
4
2
1
128 Second byte
(only the top bit is used)

Figure 7-3. Your printer takes 2 bytes to fire all 9 pins in case of
the g-pin graphics mode.

In addition, you can select the print density by the value of nO.
When nU is 0 the normal density is selected, and when nO is 1
the double density is selected.
Since computers are faster than printers, there is no signifi-
cant time loss in printing a single line of graphics with 9 pins.
You get 9 dots per line in about the same time as you get 8 dots
in the other graphics modes.
122

MEMO

Plotter Manual
100% (3)
Plotter Manual
72 pages
CompTIA A+ CertMike: Prepare. Practice. Pass the Test! Get Certified!: Core 1 Exam 220-1101
From Everand
CompTIA A+ CertMike: Prepare. Practice. Pass the Test! Get Certified!: Core 1 Exam 220-1101
Mike Chapple
No ratings yet
Integrated Software Application 1
67% (3)
Integrated Software Application 1
5 pages
Plotter Manual
No ratings yet
Plotter Manual
21 pages
TC Feature Checklist 20855 Tcm1023 95152
No ratings yet
TC Feature Checklist 20855 Tcm1023 95152
8 pages
StarLC 10 UserGuide
No ratings yet
StarLC 10 UserGuide
123 pages
Star Micronics - NR-10 and NR-15 - Users Manual
No ratings yet
Star Micronics - NR-10 and NR-15 - Users Manual
238 pages
LC 10 Clum
No ratings yet
LC 10 Clum
121 pages
Manual PLQ 20
No ratings yet
Manual PLQ 20
20 pages
User's Guide: 9-Pin Dot Matrix Printer
No ratings yet
User's Guide: 9-Pin Dot Matrix Printer
48 pages
Oki Mikroline 3410 Printer Handbook
No ratings yet
Oki Mikroline 3410 Printer Handbook
212 pages
User's Guide: 9-Pin Dot Matrix Printer
No ratings yet
User's Guide: 9-Pin Dot Matrix Printer
0 pages
LX-300+II - User's Guide
No ratings yet
LX-300+II - User's Guide
50 pages
LC 1011 Um
No ratings yet
LC 1011 Um
107 pages
User's Guide: Faqs How To Use This Manual Safety Precautions Before Printing
No ratings yet
User's Guide: Faqs How To Use This Manual Safety Precautions Before Printing
202 pages
User's Manual: Epson
No ratings yet
User's Manual: Epson
296 pages
Tutorial Printer LX 300
No ratings yet
Tutorial Printer LX 300
138 pages
Multi-Font: Users Manual
No ratings yet
Multi-Font: Users Manual
138 pages
lq680 PDF
No ratings yet
lq680 PDF
181 pages
Epson PLQ 20M User Manual
0% (1)
Epson PLQ 20M User Manual
116 pages
User's Guide: 9-Pin Dot Matrix Printer
No ratings yet
User's Guide: 9-Pin Dot Matrix Printer
0 pages
Zebra 2844 Printer Manual
No ratings yet
Zebra 2844 Printer Manual
54 pages
Epson Sty1k U1
No ratings yet
Epson Sty1k U1
123 pages
Epson Stylus Pro
No ratings yet
Epson Stylus Pro
98 pages
Epson Aculaser c2000 Setup Guide
No ratings yet
Epson Aculaser c2000 Setup Guide
83 pages
SQ 2550 U 1
No ratings yet
SQ 2550 U 1
315 pages
Users Manual: Dot Matrix Printer
No ratings yet
Users Manual: Dot Matrix Printer
130 pages
TM-U325D Um en 09
No ratings yet
TM-U325D Um en 09
47 pages
Manual Epson FX-880
No ratings yet
Manual Epson FX-880
227 pages
4041599-00 SG
No ratings yet
4041599-00 SG
2 pages
Canon Pro9000 Mark II Series (En)
No ratings yet
Canon Pro9000 Mark II Series (En)
539 pages
Servo I
No ratings yet
Servo I
94 pages
Sty15 U1
No ratings yet
Sty15 U1
119 pages
FX 286 e
No ratings yet
FX 286 e
173 pages
24-Pin Dot Matrix Printer: Reference Guide
No ratings yet
24-Pin Dot Matrix Printer: Reference Guide
160 pages
Model: Lk-Tl200: Sewoo Tech Co.,Ltd
No ratings yet
Model: Lk-Tl200: Sewoo Tech Co.,Ltd
13 pages
EPSON Stylus COLOR 440 Manual
No ratings yet
EPSON Stylus COLOR 440 Manual
168 pages
Reference Guide: 9-Pin Dot Matrix Printer
No ratings yet
Reference Guide: 9-Pin Dot Matrix Printer
133 pages
Reference Guide: 9-Pin Dot Matrix Printer
No ratings yet
Reference Guide: 9-Pin Dot Matrix Printer
133 pages
SP298 User's Manual
No ratings yet
SP298 User's Manual
136 pages
Users Manual: Dot Matrix Printer
No ratings yet
Users Manual: Dot Matrix Printer
152 pages
GENERIC SLK-TL12X Series MANUAL
No ratings yet
GENERIC SLK-TL12X Series MANUAL
13 pages
Memjet C6010 OSX - UserGuide
No ratings yet
Memjet C6010 OSX - UserGuide
100 pages
Manual Epson LQ 590 LQ 2090 PDF
No ratings yet
Manual Epson LQ 590 LQ 2090 PDF
49 pages
Epson Stylus Pro 3800 Portrait Edition
No ratings yet
Epson Stylus Pro 3800 Portrait Edition
134 pages
HP 6P/6MP: Printer User's Manual
No ratings yet
HP 6P/6MP: Printer User's Manual
142 pages
HP 6P/6MP: Printer User's Manual
No ratings yet
HP 6P/6MP: Printer User's Manual
142 pages
Epson FX Series User's Manual
No ratings yet
Epson FX Series User's Manual
268 pages
EPSON Stylus Pro 7600/9600: Printer Guide
No ratings yet
EPSON Stylus Pro 7600/9600: Printer Guide
0 pages
Generic SLK-TS400 Manual
No ratings yet
Generic SLK-TS400 Manual
13 pages
TLP 2824 Zebra Desktop Printer: User Guide
No ratings yet
TLP 2824 Zebra Desktop Printer: User Guide
60 pages
Quick Start Guide: Bubble Jet Printer
No ratings yet
Quick Start Guide: Bubble Jet Printer
26 pages
Epson Pro 3880 User Guide
No ratings yet
Epson Pro 3880 User Guide
144 pages
Thermal Printer User's Manual
No ratings yet
Thermal Printer User's Manual
40 pages
Sewoo Slk-T20eb Series User Manual Eng
No ratings yet
Sewoo Slk-T20eb Series User Manual Eng
29 pages
Deskjet 840c
No ratings yet
Deskjet 840c
67 pages
User's Manual: EPSON Stylus C42 Series
No ratings yet
User's Manual: EPSON Stylus C42 Series
53 pages
Oki User Manual c822
No ratings yet
Oki User Manual c822
143 pages
Memjet C6010 Windows UserGuide
No ratings yet
Memjet C6010 Windows UserGuide
107 pages
wf845 BB
No ratings yet
wf845 BB
4 pages
Epson MX-70 - User's Manual
No ratings yet
Epson MX-70 - User's Manual
107 pages
Correct Maintenance - Cognex DataMan 8500
From Everand
Correct Maintenance - Cognex DataMan 8500
Unique Content
No ratings yet
IIBF Vision Magazine 2025 05
No ratings yet
IIBF Vision Magazine 2025 05
8 pages
Accenture India ZMS
No ratings yet
Accenture India ZMS
8 pages
Beyond CBS: Fast Forward To Banking 2.0!
No ratings yet
Beyond CBS: Fast Forward To Banking 2.0!
13 pages
2010 New PDF
No ratings yet
2010 New PDF
243 pages
CLASS IX NOTES 2023-24 - Digital Documentation
No ratings yet
CLASS IX NOTES 2023-24 - Digital Documentation
12 pages
POS-58-Series Programmer Manual
No ratings yet
POS-58-Series Programmer Manual
57 pages
SAP PP End User Training Document
100% (1)
SAP PP End User Training Document
48 pages
COMPUTER Mcqs PDF
No ratings yet
COMPUTER Mcqs PDF
31 pages
Word Processing: Document Formatting Features
No ratings yet
Word Processing: Document Formatting Features
4 pages
Page Layout Tab
No ratings yet
Page Layout Tab
22 pages
09 Testing in Ingenium
No ratings yet
09 Testing in Ingenium
10 pages
Making Regression Tables From Stored Estimates
No ratings yet
Making Regression Tables From Stored Estimates
21 pages
Phpstorm Default Keymap Phpstorm Default Keymap Phpstorm Default Keymap
No ratings yet
Phpstorm Default Keymap Phpstorm Default Keymap Phpstorm Default Keymap
1 page
IT Lesson 4
No ratings yet
IT Lesson 4
4 pages
Pie Chart Help
No ratings yet
Pie Chart Help
8 pages
Unit 1 Digital Documentation Class 10 IT CODE 402
No ratings yet
Unit 1 Digital Documentation Class 10 IT CODE 402
22 pages
01-01 How To Use Command Lines
No ratings yet
01-01 How To Use Command Lines
10 pages
Learn RA Bill-Running Account Billing Software
No ratings yet
Learn RA Bill-Running Account Billing Software
49 pages
Vijeo Citect Architecture & Redundancy V7.2 R1 - VJC109330-02
No ratings yet
Vijeo Citect Architecture & Redundancy V7.2 R1 - VJC109330-02
244 pages
Assignment Ms Word 2007
0% (1)
Assignment Ms Word 2007
4 pages
SEL-351 Protection System Configurable Labels
No ratings yet
SEL-351 Protection System Configurable Labels
4 pages
SEG-Y Detective - User Manual, Revision of 25.05.2010
No ratings yet
SEG-Y Detective - User Manual, Revision of 25.05.2010
8 pages
Excel Shortcuts List Excel Campus
100% (1)
Excel Shortcuts List Excel Campus
9 pages
978 1 63057 551 9 1 E9e6lpkeqm
No ratings yet
978 1 63057 551 9 1 E9e6lpkeqm
24 pages
Excel Practic Exam 3
No ratings yet
Excel Practic Exam 3
65 pages
DataLogger Inglês
100% (1)
DataLogger Inglês
19 pages
TrafficAnalyst Manual en US
No ratings yet
TrafficAnalyst Manual en US
146 pages
Revit MEP - Let Me Try - LINKING REVIT MODELS
No ratings yet
Revit MEP - Let Me Try - LINKING REVIT MODELS
14 pages
SQL DBX
No ratings yet
SQL DBX
57 pages
Microsoft Word Note1 2011
No ratings yet
Microsoft Word Note1 2011
12 pages
Citect-Quickstart Tutorial Programming
100% (1)
Citect-Quickstart Tutorial Programming
67 pages
PDF Tri Strategic Facility Plan
No ratings yet
PDF Tri Strategic Facility Plan
56 pages

User'S Manual: Not Intended For Sale

Uploaded by

User'S Manual: Not Intended For Sale

Uploaded by

NX-10

NOT INTENDED FOR SALE

Topyright 1986 Star Micronics Co., Ltd.

Chapter 7 Dot Graphics 101

Appendix D Function Codes 165

Subjects we’ll cover in Chapter 1 include-

WHERE SHALL WE PUT IT?

Before you do anything else, give some thought to where

, l Using the printer on a flat surface.

WHAT HAVE WE HERE?

Now let’s take a look at what’s in the carton. Open it up and

Let’s move on the next step.

n Removing the printer cover

Removing the printer cover is easy. Lift up the back of the

.gure 1-2. Remove the printer cover by lifting carefully.

.I, n Removing the packing tube

Up to this point, we’ve been clearing the decks for action, so

n Installing the ribbon cartridge

Or, if you feel better following written instructions, read on.

1. Turn off the power and remove the printer cover.

Warning: The print head gets hot during operation, so

3. Using the guide holders as a fulcrum with the ribbon fac-

Subjects we’ll cover in Chapter 2 include -

l Connecting your printer to the computer;

l Extra functions with the control panel.

CONTROLS AND PARTS OF THE PRINTER

H Parts of the printer

PRINTER COVER - This protects the ribbon and the print

Figure 2- 1. Front and rear views of the printer

TRACTOR FEED UNIT - The drive gear and sprockets of

n Controls and indicators

. Figure 2-2. The control panel.

w. POWER INDICATOR - Glows red when the power is on or

the paper one line at a time

POWER SWITCH - The switch to turn the printer on is at

SELECTING AND LOADING PAPER

Your printer can handle the two basic types of paper-single

you’ll be using often. This lever controls the pressure of the

n Loading single sheets

OK? Let’s start.

4. Insert the guide stand in the notches provided for it and

9. Now set the release lever to the auto-feed setting-the

To align paper that is not in straight-

n Loading sprocket-feed paper

Figure 2-7. Open the sprocket covers to expose me sproaet teem.

5. Flip the clamp levers backward. This allows the two

“igure 2-8. Ready to run with sprocket-feed paper.

Figure 2-9. The adjustment lever allows for different thicknesses -

CONNECTING THE PRINTER

1. Make sure both your computer and printer are turned

‘EXTRA FUNCTIONS WITH THE CONTROL PANEL

There are many functions that are not directly specified on

Figure 2-11. Extra functions while turning on the printer.

1. Plug in the printer (don’t turn it on yet).

Paper Feed key-Self-test 1 (long)

1. Plug in the printer (don’t turn it on yet).

1. Plug in the printer (don’t turn it on yet).

1. Plug in the printer (don’t turn it on yet).

This mode stays on until you send the cancel command to

n Italic and Panel mode

Right margin set

**: Hold down L- Left margin set

n Setting print start position

n Setting the left and right margins

1. Set the Off Line mode by pressing the On Line key.

Subjects we’ll cover in Chapter 3 include-

l Control codes, escape codes, and command syn-

l Fixed and proportional character spacing;

, To show you how to control your printer from a program, we

SOME BASICS OF BASIC

language, perhaps recalling the rigors of high-school Latin.

The PR#l tells the Apple to send everything to the printer,

output to the screen.

W ASCII codes and the CHR$ function

10 1 Demo of ASCII code

line feed -the name of the code