.
63 16 Total Gap Typical
423.21 10750 Available Length
Scale 1:30
Partial Development of Shell Lining
Center Line of Mill
72° 1 8
72°
1 8
2
2 A 2
A 2
3 3
3 3
4
4 4 5 6 6 6 6 7 4
18°
15° 36°
18° 15°
36° Scale 1:30
Scale 1:30 Scale 1:30
Partial Assembly of Feed End Partial Assembly of Discharge End
3.4 87
3.0 76
R2.5 64
8
7.0 17
8° 8° R2.5 64
3.75 9
5
8.0 203
9 Filler Strip 192 @ 105" = 1680' NSS-L-19 - Rubber
6.0 15
GRADE 5 OVAL TAPERED HEAD BOLT - QUANTITIES & DIMENSIONS
3.0 7
9 17.31 44
0 Scale 1:8 8 DE Inner End Liner 5 1732-07-01A A 1164 Norsteel 8Z
.50 13 r d Section A-A
Bolt Nominal Liner Bolt Dimensions Total Gap Cho
Bolt Color Stock Number Typical End Liner Profile 7 DE Shell Liner 48 1732-08-03E E 1769 Norchrome 75
6
Qty.
2
Location Size
A F H B S T L
Rojo 1 6 Center Shell Liner 192 1732-08-02E E 1697 Norchrome75
F1 2.00" 40 2.00" 3.50" 3.50" 1.31" 13.00" 6.00" 17.81" Scale 1:8
F2 2.00" 80 2.00" 3.50" 3.50" 1.31" 11.75" 6.00" 16.56" Rojo 2 Shell Liner Profile 5 FE Shell Liner 48 1732-08-01E E 1773 Norchrome 75
F3 2.00" 80 2.00" 3.50" 3.50" 1.31" 11.00" 6.00" 15.81" Rojo 3
4 Filler Ring Segment 48 1732-05-01A A 70 Rubber
S1 2.00" 48 2.00" 3.50" 1.00" 1.31" 12.00" 6.00" 14.31" Verde 1
S2 2.00" 48 2.00" 3.50" 1.00" 1.31" 9.75" 6.00" 12.06" Verde 2 3 Outer End Liner 40 1732-04-01A A 2092 Norsteel 8Z
S3 2.00" 768 2.00" 3.50" 1.00" 1.31" 8.75" 6.00" 11.06" Verde 3
2 Middle End Liner 20 1732-03-01A A 1995 Norsteel 8Z
T1 2.00" 40 2"-4.5UNC x 5.5" Hex Head 5.50" 3.00" Azul 1
1 FE Inner End Liner 5 1732-02-01A A 1376 Norsteel 8Z
NOTES: DRAWING STATUS: BY DATE Item Description Stock number Qty/Mill Pattern no. Revision Est. Wt./Pc/Lb Material
Letter
PRELIMINARY
Nominal
1. For manufacturing use inches and inch tolerances. Title:
F
Size GL
LINER ASSEMBLY-ANTAMINA PROJECT
FOR APPROVAL Oct 02 2008
2. .25"[6mm] Rubber backing throughout mill.
3. Material Hardness: APPROVED AS MARKED
For 24'-0" X 35'-5" Long - FULLER BALL MILL
T 1. Norchrome 75: 600 BHN min.
H B S Bolt Assemblies To Include a Rubber Seal, 2. Norsteel 8Z: 350-400 BHN CERTIFIED FOR CONSTRUCTION
A L Ductile Cup Washer , and Nyloc Nut as Shown.
FOUNDRY APPROVAL Customer:
Note: Bolt Assembly Not To Scale.
FULLER MINERAL PROCESSING
UNLESS OTHERWISE SPECIFIED - STANDARD DIMENSIONAL TOLERANCES
0 Dec. Place 0 ±.25" [6mm]
F F F D Columns added to title block and bolt chart. Note #3 added 10.02.08 L.W. ANTAMINA, PERU
Rotation
0" [0mm] - 20" [508mm]
C Assembly updated to suite liner revisions.
REVISIONS
01.24.08 TF
Mill
1 Dec. Place 0.0 ±.125" [3mm] D D D
HEAD OFFICE-Toronto, Ontario
2 Dec. Place 0.00 ±.063" [1.6mm]
3 Dec. Place 0.000 ±.046"[1.2mm] RIGHT HAND LEFT HAND BI-ROTATION B Filler strip quantity & length revised.
Ref. FFE dwg 1502859 REV.1 FOUNDRY - Mont-Joli, Quebec
Over 20" [508mm] - 36"[914mm] ±.125" [3mm] Surface Finish
1000 GEOMETRIC SYMBOLS:
Parallelism True Position Pattern numbers added to title block. 02.22.00 GL SCALE 1:30 / 1:8
Over 36" [914mm] ±.188" [5mm] Flatness These drawings are confidential and subject to Copyright and shall not be copied
A Assembly update. 1732-01
01.21.00 GL DWG. REV.
Break Corners .25"R[6mm] or .25"[6mm] Chamfer Angle Tol. ± 1 Straightness Angularity Concentricity NO.
D
or reproduced in any form without prior permission of Owner, NORCAST.
Inside Fillets .13"R[3mm] - .25"R[6mm] Holes: +.13"[3mm] -.00" Perpendicularity Symmetry Roudness Rev. mm.dd.yy Sign. Rev. mm.dd.yy Sign. Drawn By: Date: January 24, 2008 Sheet no. 3ss
TONY FACCIOLO 1 of 1
