DSK multi-button pendant switches

0698 EN 202 836 44 714 IS 951 1

 DSK multi-button pendant switches

DSK multi-button pendant switches are hand-operated controls for machinery and,
more particularly, for controlling hoisting equipment from the floor. By fitting various
switching elements, it is possible to use the switches for the direct-on-line-control of
drive motors with an output of up to 5,5 kW. Motors with a higher output are control-
led via auxiliary circuits with contactors.

Design features • The sloping housing of the pendant permits operators to work in a natural comfort-
able position.
• Fatigue-free operation with ergonomically styled housing.
• Movements in opposite directions are prevented by mechanically interlocked
switching elements.
• CBDN switching element (emergency-stop) without jump function, with automatic
disconnection of the normally closed contacts.
• For direct-on-line control, 2-pole switching by simultaneous operation of snap-
action contacts.
• Identical design for direct-on-line and contactor control.
• Control paths and forces to the relevant standards (e.g. to DIN 33 401), hold down
force < 8 N.
• Housing of high-quality thermoplastic material, high shock and impact resistance.
• Protective insulation in accordance with the relevant international standards (e.g.
DIN VDE 0100 Part 410, section 4.13.2).
• Type of enclosure IP 55 to DIN VDE 0470/EN60529 in “suspended” operating
position, IP 65 on request.
• Flame-resistant housing, climate-proof and corrosion-resistant.
41438544.eps 41438644.eps
• Resistant to fuels, salt water, grease, oil and alkaline solutions.
• Permissible ambient temperatures: rubber and thermoplastic parts -25° C to +70° C.

Design and mounting information

Design
The casings of the pendant switches are made of high-quality thermoplastic material.
The upper part of the casing is black (RAL 9005), the lower part yellow (RAL 1007).
The pendant switch casings are ergonomically styled for easy operation, even with
gloves, for instance in plants with a hot atmosphere. The buttons have a large surface
and require low operating and holding forces. The required holding force when
switching is below 8 N, thus conforming with relevant standards (e.g. DIN 33 401).
The sloping casing design of the DSK control pendant enables operators to work in a
natural position, thereby reducing fatigue. A raised edge at the lower end of the cas-
ing helps prevent the operator’s hand from sliding off.
Movements in opposite directions are prevented by mechanically interlocked switch-
ing elements.
The identification plates beneath the buttons can be fitted without removing the
switching elements. The arrow symbols on the identification plates correspond to DIN
15 012, draft 2.88. Colours: yellow symbol on black background.

2
 Standards
DSE multi-button pendant switches comply with most relevant international stand-
ards and codes of practice, e.g. VDE 0660, IEC publications 337-1 and 158-1 as
well as CSA (Canada), UL (USA) and SEV (Switzerland) regulations.

Material properties
The material of the pendant switch casings is flame and impact resistant and self-
extinguishing (according to relevant standards and codes of practice). It is resistant to
corrosion and unaffected by extreme climatic conditions. Furthermore, it is resistant
to fuels, oil, grease, salt water and alkaline solutions. The materials used are suitable
for arduous mechanical and electrical duty.
The maximum permissible ambient temperature for rubber and thermoplastic parts is
-25° C to +70° C.

Type of enclosure
When assembled, the control pendants have IP 55 type of enclosure acc. to DIN
VDE 0470/EN 60529, IEC 529. IP 65 enclosure is available on request, i.e. they are
then dust-tight and protected against hose-water from all directions.

Protective insulation
High electrical safety due to protective insulation in accordance with relevant stand-
ards and codes of practice, e.g. DIN VDE 0100 Part 410, section 4.13.2.

Cable entry and strain relief

DSK pendant switches are fitted with a high-tensile flexible hose to relieve the strain
on the control cable, as standard. At the same time, the flexible hose protects the
control cable fitted inside. The maximum possible diameter of the cable used with
this hose is 18,5 mm.
For additional strain relief by rope or chain or for control pendants supplied as solo
units (without cable), strain relief may be effected as indicated in data sheet
206 489 44.

Explanation of type coding Switching elements

Single-pressure C B D 1
Double-pressure C B D 2
Emergency-stop C B D N

Block switching element

D = Direct control S = Contactor control

1 = Single-pressure, 2 = Double-pressure, N = Emergency-stop

Explanation of type coding

e.g. D S K 3 D P 2

D = Demag

S = Control switch

K = Compact

3 = Openings for switching elements

D = Direct control S = Contactor control

Emergency-stop with: P = Palm-operated button, 0 = Dummy plug

Hoist unit: 2 = Double-pressure, 1 = Single-pressure

3
 Standard DSK control pendant switches

Standard design, complete for direct and contactor control, without control cable for
CBD 1 switching element all drives.
With control cable for direct control of DK (PK) hoist units.
Identification Type Cable 1) Part no. Switching elements Weight
53 63
plate fitted
54 64 Leads
2) V1 m Qty Type kg
x mm²
- - 874 681 44 0,470
W1 0,8 874 698 44 0,930
14 24 1,8 874 699 44 1,370
L2 13
DSK 3 DO 1 2,8 874 700 44 1 CB D 1 1,800
L3
23 4 x 1,5
3,8 874 701 44 2,240
4,8 874 702 44 2,680
41059044.eps 6,8 874 703 44 3,550
- - 874 682 44 0,500
0,8 874 704 44 1,000
1,8 874 705 44 1,500
DSK 3 DO 2 2,8 874 706 44 1 CB D 2 1,900
6 x 1,5
3,8 874 707 44 2,370
CBD 2 switching element 4,8 874 708 44 2,820
6,8 874 709 44 3,750
012 63 53
1W1 1V1 2V1 2W1 - - 874 683 44 0,540
Emergency- 0,8 772 358 44 1 CB DN 1,040
64 54 stop
12 22 34 44 1,8 874 710 44 1,500
DSK 3 DP 1 2,8 874 711 44 1 CB D 1 1,950
2) 11 21 33 43 6 x 1,5
3,8 772 359 44 2,400
012 14 24
4,8 874 712 44 2,860
13 23 6,8 772 360 44 3,770
- - 874 684 44 0,570
L2 L3 Emergency- 0,8 772 361 44 1 CB DN 1,070
stop 1,8 874 713 44 1,680
DSK 3 DP 2 2,8 874 714 44 1 CB D 2 2,210
41057644.eps 8 x 1,5
3,8 772 362 44 2,810
4,8 772 363 44 3,390
6,8 772 364 44 4,580

CBS 1 switching element

With control cable for contactor control of DK (PK) hoist units.
53 Identification Type Cable 1) Part no. Switching elements Weight
plate fitted
54
Lifting Leads
m Qty Type kg
x mm²
Lowering - - 772 193 44 0,450
14 0,8 772 915 44 0,900
1,8 772 916 44 1,350
L4 13
DSK 3 SO 1 2,8 772 917 44 1 CB S 1 1,780
4 x 1,5
41274144.eps
3,8 772 918 44 2,220
4,8 772 919 44 2,660
CBS 2 switching element 6,8 772 920 44 3,530
Lowering

- - 772 194 44 0,480

Lifting
Fast

0,8 772 921 44 0,980

1,8 772 922 44 1,480
012 53
DSK 3 SO 2 2,8 772 923 44 1 CB S 2 1,880
4 x 1,5
54 3,8 772 924 44 2,350
44
4,8 772 925 44 2,800
43 6,8 772 926 44 3,730
24
- - 772 191 44 0,520
012 23 Emergency- 0,8 772 927 44 1 CB DN 1,020
stop 2,8 772 928 44 1 CB S 1 1,930
DSK 3 SP 1
L4 3,8 4 x 1,5 772 929 44 2,480
41274244.eps
4,8 772 930 44 2,840
6,8 772 931 44 3,750
CB DN
- - 772 192 44 0,550
Emergency- 0,8 772 932 44 1 CB DN 1,050
32 22 12
stop DSK 3 SP 2 3,8 772 933 44 1 CB S 2 2,700
6 x 1,5
4,8 772 934 44 3,200
6,8 772 935 44 4,300
31 21 11 1) An additional strain relief rope must be fitted for control cables longer than 8 m.
40186144.eps
4 2) Only fit jumpers for DK and PK electric chain hoists and travel drives.
Switching elements for main and control current
Type Description Part no. Weight
kg

CB D 1 Switching element, single pressure 2 x 2 NO 874 667 44 0,12

CB D 2 Switching element, double pressure 874 668 44 0,15

1st step 2 x 2 NO, 2nd step 2 DT
CB S 1 Switching element, single pressure 2 x 1 NO 772 185 44 0,10

CB S 2 Switching element 772 188 44 0,10

double pressure
1st step 2 x 1 NO
1st step 1 two-step NO
CB DN Switching element, emergency-stop 1) 3 NC 874 658 44 0,06

Emergency-stop button with identification plate 874 666 44, 874 718 44 0,018
cpl. (Can only be used in connection with switching element
CB DN)
1) Can only be fitted in connection with emergency-stop button 874 718 44

Emergency-stop button CB DN Wall bracket

11
12

21
22

31
32
44

43
2W1 2V1

34

33
22

21
1W1 1V1

12

11
63 53

64 54

14 24
13 23

27
L3
L2
012

012

27

CB D 1 / CB D 2 / CB S 1 / CB S 2

41438044.eps 40456244.eps

Accessories

Special flexible hose for DSK, protection and strain relief for 872 242 44 0,27/m
control cable inside, inner diameter 20 mm
Threaded bush Pg 16 (for securing special flexible hose, e.g. 872 240 44 0,100
PK hoist, inner diameter 16 mm)
Slide bush (for securing special flexible hose to DK, inner 836 051 44 0,018/m
diameter 19 mm)
Complete DSK wall bracket for DSK units. The DSK can be 874 768 44 0,155
DSK-W permanently fixed to the wall bracket.
Permanent fixture is only permissible for stationary controls.
Control cable YMHYK-O 4 x 1,5 504 935 44 0,166/m

Control cable YMHYK-O 6 x 1,5 504 936 44 0,187/m

Control cable YMHYK-O 8 x 1,5 504 938 44 0,256/m

Control cable YMHYK-O 4 x 2, 5 504 941 44 0,230/m

Control cable YMHYK-O 6 x 2,5 504 942 44 0,266/m

Control cable YMHYK-O 8 x 2,5 504 944 44 0,376/m

Cable sleeve Ø 12 - 18 872 367 44 0,08

Strain relief bracket 874 725 44 0,09

3 NC fail-safe (emergency-stop button with switching element) 772 876 44 0,09

5
 Component parts for DSK control pendant switch

Identification plates
Type Description Part no. Weight
kg
Hoist unit, 874 665 44 0,005
single or double-pressure
Emergency-stop/hoist unit, 874 666 44 0,005
Front single or double-pressure

Identification plates with part no. 874 66. 44 are printed on both sides.

Front and rear side:

Black background with yellow symbol.
Rear
Colour:
Silken yellow according to RAL 1007, silken black according to RAL 9005.

Front

Rear
40255544.eps

6
Technical data

Switching elements
Switching element Type CB D 1 CB D 2 CB DN CB S 1 CB S 2
Contacts 2 x 2 NO 1st step 3 NC 2 x 1 NO 1st step
Steps 1 2 x 2 NO 1 1 2 x 1 NC
2nd step 2nd step
2 DT 1 two-step NO
Nominal insulation voltage Ui
VDE 0110, gr. C V~ 500
Canada C 22 2 no. 14 Va-c 150
Life in terms of switching cycles
Mechanical S 2 x 106
Electrical S see diagram 1
Max. number of switching cycles S/ h see diagram 2
Terminal screws M 3,5
Connecting lead cross section mm² max. 2 x 2,5
Max. nominal current of short-circuit fuse, delayed action A 20 20 16 16
Nominal operating current le
40 - 60 Hz for 230 V A 20 20 for 10 10
switching
400 V A 12 12 6 6
capacity
500 V A 9 9 up to 5,5 kW 4,5 4,5
Category 1) to DIN VDE 0660 AC 3, AC 4 AC 3, AC 4 AC 15
Continuous current lth 2 A 25

Casing
Type of enclosure to DIN VDE 0470/EN 60529 IP 55
IEC 529 IP 65 on request
Electrical safety Protection insulation acc. to DIN VDE 0100 part 410, section 4.13.2
Ambient temperature min/max
Rubber and thermoplastic parts °C - 25° to + 70 °C
Dia. of opening for switching element mm 22,5

1) AC 3: Normal switching conditions: up to 6 x nominal motor current

Breaking: 1 x nominal motor current
AC 4: Extreme switching conditions (operational short-impulse switching); making: 6 x nominal motor
current.
Breaking: 6 x nominal motor current (short-impulse switching should be avoided because of
strong contact erosion)
AC 15: Controlling electromagnetic loads (> 72 VA)
Diagram of operating force (F) as a func-
F[N] F[N]
tion of the operating path(s) for single-
and double-pressure switching elements 25 25

20 20

15 15

10 10

5 5

1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12
1 stufig
single-pressure s[mm] 2 stufig
double-pressure s[mm]
41438144.eps 41438244.eps

Switch life as a function of breaking

Diagram 1 Diagram 2
current 230V 400V 500V
85% AC3 - 15% AC4
120 72 54
Ia breaking current
s/h 1500
S switching cycles 100 60 45

le nominal operating current 80 48 36

10
0%
1000
900
AC 800
Ia 40 - 60 Hz

Approximate values for the max. number of switch- 4

700
AC3
60 36 27 600
ing cycles per hour (s/h) for SE switching elements 500
AC4
as a function of the nominal operating current 40 24 18 400

1 switching cycle = 20 12 9
300

1 switching on and switching off operation 200

0.02 0.04 0.1 0.2 0.3 0.5 1 10 20 30 40 50 60 70 80 90 100%
CB D CB D
0.03 0.05 e

41438344.eps 41438444.eps

7
 Reproduction in whole or in part only with prior consent of Mannesmann Dematic AG, D-58286 Subject to alteration

Mannesmann Dematic AG
P.O. Box 67, D-58286 Wetter
Telephone (+2335) 92-0, Telefax (+2335) 927676
Internet http://www.dematic.com
Printed in Germany MBR/0997/2T