Scribd Logo
Upload

Welcome to Scribd!

  • 20 views

    2016.10.31 - TP 25x25 (Japanese)

    Uploaded by

    Jason Jenal
    1) The document summarizes pile load capacity calculations for several boreholes using the Japanese formula. 2) It provides soil data, N-values, and calculated allowable compression and tension loads for 250x250mm piles at each borehole location. 3) The average allowable compression load was determined to be 45 tons, and the average allowable tension load was determined to be 10 tons for design purposes.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd

    2016.10.31 - TP 25x25 (Japanese)

    Uploaded by

    Jason Jenal
    20 views7 pages
    1) The document summarizes pile load capacity calculations for several boreholes using the Japanese formula. 2) It provides soil data, N-values, and calculated allowable compression and tension loads for 250x250mm piles at each borehole location. 3) The average allowable compression load was determined to be 45 tons, and the average allowable tension load was determined to be 10 tons for design purposes.

    Original Title

    2016.10.31_TP 25x25 (Japanese).xlsx

    Copyright

    © © All Rights Reserved

    Available Formats

    XLSX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1) The document summarizes pile load capacity calculations for several boreholes using the Japanese formula. 2) It provides soil data, N-values, and calculated allowable compression and tension loads for 250x250mm piles at each borehole location. 3) The average allowable compression load was determined to be 45 tons, and the average allowable tension load was determined to be 10 tons for design purposes.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    20 views7 pages

    2016.10.31 - TP 25x25 (Japanese)

    Uploaded by

    Jason Jenal
    1) The document summarizes pile load capacity calculations for several boreholes using the Japanese formula. 2) It provides soil data, N-values, and calculated allowable compression and tension loads for 250x250mm piles at each borehole location. 3) The average allowable compression load was determined to be 45 tons, and the average allowable tension load was determined to be 10 tons for design purposes.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    of 7

    · Stadin ·

    Structural & Consulting Engineers

    Rekapitulasi Hasil Perhitungan Daya Dukung Tiang Tekan & Tarik

    Pile 250 x 250 mm


    Data Tanah Kedalaman (m) L Efektif (m) Tekan (Ton) Tarik (Ton)
    BH-1 -8.00 7.50 49 14
    BH-2 -8.00 7.50 50 14
    BH-3 -2.00 1.50 31 3
    BH-4 -2.00 1.50 31 3
    BH-5 -4.00 3.50 40 8
    Min. 31 3
    Rata-rata 40 8
    Max. 50 14

    Kesimpulan
    Untuk perencanaan diambil daya dukung ijin sebagai berikut :
    P ijin Tekan = 45 ton
    P ijin Tarik = 10 ton

    file:///conversion/tmp/scratch/435233483.xlsx
    Driven Pile Load Capacity ( BH-2<PT Daya Creasi Mitrayasa>)

    �_𝐮=𝐐_𝐩+𝐐_𝐬=(𝐪_𝐩 𝐱 𝐀_𝐩 )+∑▒(𝐪_𝐬 𝐱


    𝐀_𝐬 )
    �_𝐮=(𝟐𝟓 𝐱 𝐍_𝐩 𝐱 𝐀_𝐩 )+∑▒ 〖 ((𝐍_𝐬 𝐱 𝐋_𝐬)/𝟓+
    (Japanese Formula)
    (𝐍_𝐜 𝐱 𝐋_𝐜)/𝟐) 𝐱 � 〗

    Pu = Ultimate pile load capacity (Ton)


    Np = Average Nvalue ( 4 x Dia above and 1 x D below pile toe)
    Ap = Pile area (m2) = 0.25 x phi x (Dia.)2
    Ns = Average Nvalue at Sand layer
    Ls = Depth of Sand layer
    Nc = Average Nvalue at Clay layer
    Lc = Depth of Clay layer
    K = Perimeter of pile (meter)

    P allowable = ( Qp + Qs ) / 3 (Compression)

    P allowable = Qs / 5 (Tension)

    1. Data BH-1 SF = 2 (Clay / Silt) Cohesive (C)


    = 5 (Sand) Non cohesive (N)

    Pile 250 x 250 mm / Tiang Pancang

    - Tahanan Friksi

    No. Elevasi Soil Type C/N SF N SPT L qs qmax qs used N x L x K / SF


    (m) (m) (Ton/m2) (Ton/m2) (Ton/m2)
    1 -2.00 Clayey Silt C 2 21 1.50 10.50 20.00 10.50 15.75
    2 -4.00 Silty Sand C 2 24 2.00 12.00 20.00 12.00 24.00
    3 -6.00 Sand N 5 21 2.00 4.20 20.00 4.20 8.40
    4 -8.00 Sand N 5 50 2.00 10.00 20.00 10.00 20.00
    ∑ = 7.50 ∑ = 68.15

    - Tahanan Ujung
    qp = 25 x Np
    = 25 x 50
    = 1,250 Ton/m2

    K = 4 x 0.25 = 1.00 m

    Ap = 0.25 x 0.25 = 0.06 m²

    Pu = 25 x 50 x 0.06 + 68.15 = 146.28

    Daya dukung izin tekan = 146.3 = 49 Ton


    3
    Daya dukung izin tarik = 68.2 = 14 Ton
    5

    file:///conversion/tmp/scratch/435233483.xlsx
    Driven Pile Load Capacity ( BH-5<PT Daya Creasi Mitrayasa>)

    �_𝐮=𝐐_𝐩+𝐐_𝐬=(𝐪_𝐩 𝐱 𝐀_𝐩 )+∑▒(𝐪_𝐬 𝐱


    𝐀_𝐬 )
    �_𝐮=(𝟐𝟓 𝐱 𝐍_𝐩 𝐱 𝐀_𝐩 )+∑▒ 〖 ((𝐍_𝐬 𝐱 𝐋_𝐬)/𝟓+
    (Japanese Formula)
    (𝐍_𝐜 𝐱 𝐋_𝐜)/𝟐) 𝐱 � 〗

    Pu = Ultimate pile load capacity (Ton)


    Np = Average Nvalue ( 4 x Dia above and 1 x D below pile toe)
    Ap = Pile area (m2) = 0.25 x phi x (Dia.)2
    Ns = Average Nvalue at Sand layer
    Ls = Depth of Sand layer
    Nc = Average Nvalue at Clay layer
    Lc = Depth of Clay layer
    K = Perimeter of pile (meter)

    P allowable = ( Qp + Qs ) / 3 (Compression)

    P allowable = Qs / 5 (Tension)

    1. Data BH-2 SF = 2 (Clay / Silt) Cohesive (C)


    = 5 (Sand) Non cohesive (N)

    Pile 250 x 250 mm / Tiang Pancang

    - Tahanan Friksi

    No. Elevasi Soil Type C/N SF N SPT L qs qmax qs used N x L x K / SF


    (m) (m) (Ton/m2) (Ton/m2) (Ton/m2)
    1 -2.00 Clayey Silt C 2 31 1.50 15.50 20.00 15.50 23.25
    2 -4.00 Clayey Silt C 2 16 2.00 8.00 20.00 8.00 16.00
    3 -6.00 Silty Sand N 5 29 2.00 5.80 20.00 5.80 11.60
    4 -8.00 Silty Sand N 5 50 2.00 10.00 20.00 10.00 20.00
    ∑ = 7.50 ∑ = 70.85

    - Tahanan Ujung
    qp = 25 x Np
    = 25 x 50
    = 1,250 Ton/m2

    K = 4 x 0.25 = 1.00 m

    Ap = 0.25 x 0.25 = 0.06 m²

    Pu = 25 x 50 x 0.06 + 70.85 = 148.98

    Daya dukung izin tekan = 149.0 = 50 Ton


    3
    Daya dukung izin tarik = 70.9 = 14 Ton
    5

    file:///conversion/tmp/scratch/435233483.xlsx
    Driven Pile Load Capacity ( BH-6<PT Daya Creasi Mitrayasa>)

    �_𝐮=𝐐_𝐩+𝐐_𝐬=(𝐪_𝐩 𝐱 𝐀_𝐩 )+∑▒(𝐪_𝐬 𝐱


    𝐀_𝐬 )
    �_𝐮=(𝟐𝟓 𝐱 𝐍_𝐩 𝐱 𝐀_𝐩 )+∑▒ 〖 ((𝐍_𝐬 𝐱 𝐋_𝐬)/𝟓+
    (Japanese Formula)
    (𝐍_𝐜 𝐱 𝐋_𝐜)/𝟐) 𝐱 � 〗

    Pu = Ultimate pile load capacity (Ton)


    Np = Average Nvalue ( 4 x Dia above and 1 x D below pile toe)
    Ap = Pile area (m2) = 0.25 x phi x (Dia.)2
    Ns = Average Nvalue at Sand layer
    Ls = Depth of Sand layer
    Nc = Average Nvalue at Clay layer
    Lc = Depth of Clay layer
    K = Perimeter of pile (meter)

    P allowable = ( Qp + Qs ) / 3 (Compression)

    P allowable = Qs / 5 (Tension)

    1. Data BH-3 SF = 2 (Clay / Silt) Cohesive (C)


    = 5 (Sand) Non cohesive (N)

    Pile 250 x 250 mm / Tiang Pancang

    - Tahanan Friksi

    No. Elevasi Soil Type C/N SF N SPT L qs qmax qs used N x L x K / SF


    (m) (m) (Ton/m2) (Ton/m2) (Ton/m2)
    1 -2.00 Silty Sand N 5 50 1.50 10.00 20.00 10.00 15.00
    ∑ = 1.50 ∑ = 15.00

    - Tahanan Ujung
    qp = 25 x Np
    = 25 x 50
    = 1,250 Ton/m2

    K = 4 x 0.25 = 1.00 m

    Ap = 0.25 x 0.25 = 0.06 m²

    Pu = 25 x 50 x 0.06 + 15.00 = 93.13

    Daya dukung izin tekan = 93.1 = 31 Ton


    3
    Daya dukung izin tarik = 15.0 = 3 Ton
    5

    file:///conversion/tmp/scratch/435233483.xlsx
    Driven Pile Load Capacity ( BH-6<PT Daya Creasi Mitrayasa>)

    �_𝐮=𝐐_𝐩+𝐐_𝐬=(𝐪_𝐩 𝐱 𝐀_𝐩 )+∑▒(𝐪_𝐬 𝐱


    𝐀_𝐬 )
    �_𝐮=(𝟐𝟓 𝐱 𝐍_𝐩 𝐱 𝐀_𝐩 )+∑▒ 〖 ((𝐍_𝐬 𝐱 𝐋_𝐬)/𝟓+
    (Japanese Formula)
    (𝐍_𝐜 𝐱 𝐋_𝐜)/𝟐) 𝐱 � 〗

    Pu = Ultimate pile load capacity (Ton)


    Np = Average Nvalue ( 4 x Dia above and 1 x D below pile toe)
    Ap = Pile area (m2) = 0.25 x phi x (Dia.)2
    Ns = Average Nvalue at Sand layer
    Ls = Depth of Sand layer
    Nc = Average Nvalue at Clay layer
    Lc = Depth of Clay layer
    K = Perimeter of pile (meter)

    P allowable = ( Qp + Qs ) / 3 (Compression)

    P allowable = Qs / 5 (Tension)

    1. Data BH-4 SF = 2 (Clay / Silt) Cohesive (C)


    = 5 (Sand) Non cohesive (N)

    Pile 250 x 250 mm / Tiang Pancang

    - Tahanan Friksi

    No. Elevasi Soil Type C/N SF N SPT L qs qmax qs used N x L x K / SF


    (m) (m) (Ton/m2) (Ton/m2) (Ton/m2)
    1 -2.00 Silty Sand N 5 50 1.50 10.00 20.00 10.00 15.00
    ∑ = 1.50 ∑ = 15.00

    - Tahanan Ujung
    qp = 25 x Np
    = 25 x 50
    = 1,250 Ton/m2

    K = 4 x 0.25 = 1.00 m

    Ap = 0.25 x 0.25 = 0.06 m²

    Pu = 25 x 50 x 0.06 + 15.00 = 93.13

    Daya dukung izin tekan = 93.1 = 31 Ton


    3
    Daya dukung izin tarik = 15.0 = 3 Ton
    5

    file:///conversion/tmp/scratch/435233483.xlsx
    Driven Pile Load Capacity ( BH-5<PT Daya Creasi Mitrayasa>)

    �_𝐮=𝐐_𝐩+𝐐_𝐬=(𝐪_𝐩 𝐱 𝐀_𝐩 )+∑▒(𝐪_𝐬 𝐱


    𝐀_𝐬 )
    �_𝐮=(𝟐𝟓 𝐱 𝐍_𝐩 𝐱 𝐀_𝐩 )+∑▒ 〖 ((𝐍_𝐬 𝐱 𝐋_𝐬)/𝟓+
    (Japanese Formula)
    (𝐍_𝐜 𝐱 𝐋_𝐜)/𝟐) 𝐱 � 〗

    Pu = Ultimate pile load capacity (Ton)


    Np = Average Nvalue ( 4 x Dia above and 1 x D below pile toe)
    Ap = Pile area (m2) = 0.25 x phi x (Dia.)2
    Ns = Average Nvalue at Sand layer
    Ls = Depth of Sand layer
    Nc = Average Nvalue at Clay layer
    Lc = Depth of Clay layer
    K = Perimeter of pile (meter)

    P allowable = ( Qp + Qs ) / 3 (Compression)

    P allowable = Qs / 5 (Tension)

    1. Data BH-5 SF = 2 (Clay / Silt) Cohesive (C)


    = 5 (Sand) Non cohesive (N)

    Pile 250 x 250 mm / Tiang Pancang

    - Tahanan Friksi

    No. Elevasi Soil Type C/N SF N SPT L qs qmax qs used N x L x K / SF


    (m) (m) (Ton/m2) (Ton/m2) (Ton/m2)
    1 -2.00 Clayey Silt C 2 28 1.50 14.00 20.00 14.00 21.00
    2 -4.00 Sand N 5 50 2.00 10.00 20.00 10.00 20.00
    ∑ = 3.50 ∑ = 41.00

    - Tahanan Ujung
    qp = 25 x Np
    = 25 x 50
    = 1,250 Ton/m2

    K = 4 x 0.25 = 1.00 m

    Ap = 0.25 x 0.25 = 0.06 m²

    Pu = 25 x 50 x 0.06 + 41.00 = 119.13

    Daya dukung izin tekan = 119.1 = 40 Ton


    3
    Daya dukung izin tarik = 41.0 = 8 Ton
    5

    file:///conversion/tmp/scratch/435233483.xlsx
    Daya Dukung Tiang Pancang 450 x 450 mm
    Depth vs Pizin
    -1.00
    meter

    -2.00

    -3.00
    0 5 10 15 20 25 30 35

    ton

    BH-1 (-14m)

    file:///conversion/tmp/scratch/435233483.xlsx

    You might also like