HBE-95

High Build Epoxy coating for pipelines

The Canusa HBE-95 is an advanced two-component epoxy
coating system which has been specifically formulated for
moderate temperature pipelines. Applied to bare steel, HBE-95 has
proven to withstand operating temperatures up to 95°C (203°F)
with superior performance. HBE-95 is used for protection of field
joint girth welds, valves and fittings, as a holiday repair material on
FBE coated pipe or for rehabilitation projects. This environmentally
friendly, 100% solids, novolac epoxy system can either be spray
applied or brush applied to the intended substrate.

Applications

Corrosion Protection up to 95°C

Oil & Gas
• HBE-95 coating system was designed to protect operating
pipelines up to 95°C with exceptional performance.
Repair & Rehab
Exceeds FBE Performance Requirements
• Exceeds FBE coating performance requirements, including impact
resistance, hot water soak adhesion and resistance to cathodic Abrasion Coating
disbonding, as specified in USA (NACE RP0394), British (CW6),
and Canadian (CSA Z245.20) standards.
Girth-Weld Joints
Fast, Medium and Slow Cure Options
• HBE-95 brush grade comes with three different cure speed
Fittings & Bends
options: Fast, Medium and Slow. Cure speed options present pot-
life flexibility based on ambient temperatures and cycle
cle time
requirements.
High Build in Single Coat
• A single pass application direct-to-metal will achieve
e a high
build coating thickness of 20-40mils (500-1000microns).
rons).
Variety of Uses
• Mainline pipelines, rehabilitation projects, girth weld field joints,
damage and holiday repair to FBE coated pipe, pipeline ne
valves, fittings and bends, or directional drilling
applications.

PRODUCT DATA SHEET canusacps.com

 The product information
shown here is intended as a guide
HBE-95 for standard products.

Consult your Canusa

High Build Epoxy coating for pipelines representative for specific
projects or unique applications.

Performance All performance testing followed CSA-Z245.20-10 unless specified.

Service Temp. Up to 95°C (203°F)

Typical Thickness > 20 mils (500 microns)
Mixing Ratio 3:1 (by volume)
Percent Solids 100%
Base: 1.49
Specific Gravity
Cure: 1.048
Hardness (ASTM D2240) > 85 Shore D
Adhesion to Steel > 2300 psi
Adhesion to FBE > 2000 psi
Cathodic Disbondment @ 28 days, 23°C < 3 mm
Cathodic Disbondment @ 28 days, 80°C < 8 mm Canusa-CPS
A division of Shawcor Ltd.
Cathodic Disbondment @ 28 days, 95°C < 8 mm
Head Office
Impact Resistance @ -30°C > 3.0 J
25 Bethridge Road
Impact Resistance @ 25°C > 3.0 J Toronto, ON, Canada M9W 1M7
Tel: +1 416 743 7111
Hot Water Immersion @ 28 days, 75°C Rating 1 Fax: +1 416 743 5927

Hot Water Immersion @ 28 day, 95°C Rating 1 Canada

Dome Tower St. 2200, 333-7th Avenue SW
Water Absorption (ASTM D570) < 0.1 % Calgary, AB, Canada T2P 2Z1
Chemical Resistance (ASTM D543) Excellent in various pH solutions Tel: +1 403 218 8207
Fax: +1 403 264 3649
3 years when stored in original packaging Americas
Shelf Life
between 5°C and 40°C.
5875 N. Sam Houston Pkwy W., Suite 200
Cure Speed Options1 Houston, TX, USA 77086
Tel: +1 281 886 2350
SuperFast Cure2 (SFT) Gel Time = Forced Cure Fax: +1 281 886 2353

Fast Cure (WG) Gel Time = < 10 minutes Middle East

ADPC - Mussafah Port, P.O. Box 2621
Medium Cure (XG) Gel Time = < 15 minutes Abu Dhabi, UAE
Tel: +971 2 496 3500
Slow Cure (RG) Gel Time = < 20 minutes Fax: +971 2 496 3501
3
Typical Kit Size Required by Pipe Diameter Europe, Africa & Russia
4.5” – 16” 0.5 Liter Kit Dellaertweg 9-E, Gebouw “Le Carrefour”
2316 WZ Leiden, The Netherlands (NL)
18” – 32” 1.0 Liter Kit Tel: +31 71 80 802 70
Fax: +31 71 80 802 71
34” to 50” 1.5 Liter Kit
Asia-Pacific
1 Gel times were measured @ 23°C (73°F). For more information please refer to Canusa’s Technical Bulletin – High Build Epoxy Cure Profiles. 101 Thomson Road, #11-03 United Square
2 SuperFast Technology (SFT) is used as repair material in FBE coating plants. 307591 Singapore
3 Based on 400 mm coating width, 25 mils (635 micron) average thickness and 50% wastage factor. Tel: +65 6749 8918
Fax: +65 6749 8919

Quality Management system

registered to ISO 9001
Safety Canusa warrants that the product conforms to its
chemical and physical description and is appropriate
for the use stated on the product data sheet when
Handle with care. Before and during use, observe all safety labels on packaging used in compliance with Canusa’s written instructions.
Since many installation factors are beyond our control,
containers, consult with Canusa-CPS Material Safety Data Sheets and abide by all the user shall determine the suitability of the products
for the intended use and assume all risks and liabilities
local or national safety regulations. in connection therewith. Canusa’s liability is stated
in the standard terms and conditions of sale. Canusa
makes no other warranty either expressed or implied.
Since 1967, Canusa-CPS has been a leading developer and manufacturer of specialty pipeline coatings All information contained in this data sheet is to be
used as a guide and is subject to change without
for the sealing and corrosion protection of pipeline joints and other substrates. Canusa-CPS high notice. This data sheet supersedes all previous data
sheets on this product. E&OE
performance products are manufactured to the highest quality standards and are available in a number
of configurations to accommodate many specific project applications. PDS_HBE-95_rev024