KENR9522 Harness And Wire Electrical Schematic Symbols

March 2009
Symbols

Pressure Temperature Level Flow Circuit Breaker

Symbol Symbol Symbol Symbol Symbol

Symbols and Definitions

Fuse: A component in an electrical circuit that will open the circuit if too much current flows
through it.

Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The
circle indicates that the component has screw terminals and a wire can be disconnected from it.

Switch (Normally Closed): A switch that will open at a specified point (temp, press, etc.).
No circle indicates that the wire cannot be disconnected from the component.

Ground (Wired): This indicates that the component is connected to a grounded wire. The
grounded wire is fastened to the machine.

Ground (Case): This indicates that the component does not have a wire connected to ground.
It is grounded by being fastened to the machine.

Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the
contacts of a normally open reed switch; it opens the contacts of a normally closed reed switch.

311C U, 312C, 314C, 315C, and Sender: A component that is used with a temperature or pressure gauge. The sender
measures the temperature or pressure. Its resistance changes to give an indication to

318C Excavator
T
the gauge of the temperature or pressure.

Electrical System - Attachment

Relay (Magnetic Switch): A relay is an electrical component that is activated by electricity.
It has a coil that makes an electromagnet when current flows through it. The
electromagnet can open or close the switch part of the relay.

Solenoid: A solenoid is an electrical component that is activated by electricity. It has a

311C U: 312C: 314C: 315C: coil that makes an electromagnet when current flows through it. The electromagnet
can open or close a valve or move a piece of metal that can do work.
PAD1-UP CBA1-UP KJA1-UP CJC1-UP
CKE1-UP BWH1-UP PCA1-UP AKE1-UP Magnetic Latch Solenoid: A magnetic latch solenoid is an electrical component that is
activated by electricity and held latched by a permanent magnet. It has two coils (latch and unlatch)
DBN1-UP SNY1-UP ANF1-UP that make electromagnet when current flows through them. It also has an internal switch that places
the latch coil circuit open at the time the coil latches.
FDS1-UP
Harness and Wire Symbols
1 Deutsch connector: Typical representation 1 Sure-Seal connector: Typical representation
of a Deutsch connector. The plug contains all of a Sure-Seal connector. The plug and receptacle
2 sockets and the receptacle contains all pins. 2 contain both pins and sockets.
318C: Harness Identification Letter(s):
Wire, Cable, or Harness Assembly Identification:
BTG1-UP Includes Harness Identification Letters and Harness
(A, B, C, ..., AA, AB, AC, ...)
Harness Connector Serialization Code: The "C" stands
Connector Serialization Codes
MDY1-UP for "Connector" and the number indicates which
connector in the harness. (C1, C2, C3, .....)
Part Number for
C-C4 AG-C3 Connector Plug AG-C4 L-C12 Part Number For
111-7898 3E-5179 Connector Recepticle
130-6795 130-6795
325-AG135 PK-14 1 5A
Pin Socket
Receptacle Fuse
Pin or Socket (5 Amps)
Single Wire 9X-1123
Number
Connector
Component
Plug Part Number
Harness identification code: 2 200-L32 BK-14
This example indicates wire
135 in harness "AG".
Ground Circuit Identification
Product Link Connection Number Wire Color Wire Gauge

© 2009 Caterpillar Printed in U.S.A.

All Rights Reserved
 6 5 4 3 2 1
ANTENNA

2ND GENERATION RADIO Module Identifier 122 Diagnostic Codes

238-9288 D CID 0168 Electrical System
FMI 00 Voltage Above Normal
1
F D FMI 01 Voltage Below Normal F
CID 0254 Electronic Control Module
2
FMI 04 Voltage Below Normal
FMI 12 Failed Module
BATT+ 1 172-RD-18 CID0269 Sensor Power Supply
BATT- 2 235-BK-18 FMI 03 Voltage Above Normal
KEYSWITCH ON 3 308-YL FMI 04 Voltage Below Normal
R.TERM 4 403-GN-18 CID 1250 Remote Communication Module
RS-232.TXD 5 N957-PK-18 FMI 09 Unable to Establish Communication
6 CID 1251 Alternator R-Terminal
RS232-RXD 7 N960-OR-18 FMI 03 Voltage Above Normal
RS232-GND 8 N979-GN-18 A
E RS232-OTR 9 N970-YL-18 892-BR-18 6 892-BR-18 E

N960-OR-18
N957-PK-18
N979-GN-18
N970-YL-18
N973-BR-18

172-RD-18
235-BK-18

403-GN-18
RS232-OCD 10 N973-BR-18 893-GN-18 5 893-GN-18

308-YL
11 403-GN-18 4 403-GN-18 STANDARD HARNESS
12 308-YL 3 332-BU-18
B 235-BK-18 2 235-BK-18
172-RD-18 1 114-RD-16
B B
FOR 311CU SYMBOL DESCRIPTION

1
2
3
4
5
6
1
2
3
4
5
6
CIRCUIT CONNECTED

A A
A CIRCUIT NOT CONNECTED

D 892-BR-18 6 892-BR-18 ELECTRICAL CONNECTION TO

D

N960-OR-18
N957-PK-18
N979-GN-18
N970-YL-18
N973-BR-18

172-RD-18
235-BK-18

403-GN-18
MACHINE STRUCTURE
893-GN-18 5 893-GN-18

308-YL
INTERNAL ELECTRICAL CONNECTION
403-GN-18 4 403-GN-18 STANDARD HARNESS TO SURFACE OF COMPONENT

308-YL 3 332-BU-18 CONNECTOR

PRODUCT LINK 235-BK-18 2 235-BK-18 H# CIRCUIT GROUPING DESIGNATION

239-9954 A 172-RD-18 1 103-RD-18
ATCH WIRE, CABLE, COMPONENT
RS232 PT.1-DCD 30 N973-BR-18
RS232 PT.1-DTA 23 N970-YL-18 FOR 314CCR CIRCUIT CONNECTED

RS232 PT.1-TXD 13 N957-PK-18

SPLICE
RS232 PT.1-RXD 22 N960-OR-18
BLADE, SPADE, RING OR SCREW
RS232 PT.1-GND 31 N979-GN-18 A TERMINAL
BATT+ 52 172-RD-18 892-BR-18 892-BR-18 6 892-BR-18
C C
BATT- 65 235-BK-18 893-GN-18 893-GN-18 5 893-GN-18
KEYSWTCH ON 70 308-YL 403-GN-18 403-GN-18 4 403-GN-18 STANDARD HARNESS COLOR ABBREVIATIONS
R-TERM 54 403-GN-18 308-YL 308-YL 3 308-YL
CDL+ 8 893-GN-18 235-BK-18 235-BK-18 2 235-BK-18
ABBREV COLOR
CDL- 9 892-BR-18 172-RD-18 172-RD-18 1 172-RD-18 RD RED
CAN LOW 34 WH WHITE
CAN HIGH 50 A FOR 312C. 315C. 318C OR ORANGE
CAN SHIELD 42 YL YELLOW
RS232 PT.3-GND 64 N981-GN-18 GND-CHASSIS
ET CONN PK PINK
RS232 PT.3-TXD 62 N963-OR-18
BK BLACK
RS232 PT.3-RXD 63 N959-PK-18 N963-OR-18 1 N960-OR-18 N979-GN-18 A
B 70POS N959-PK-18 2 N957-PK-18 N960-OR-18 B
GY GRAY
B
N981-GN-18 3 N979-GN-18 N957-PK-18 C PU PURPLE
4 C BR BROWN
5 GN GREEN
6 BU BLUE
A C

311CU 312C 314CCR 315C 318C THIS SCHEMATIC IS FOR THE 311C U, 312C, 314C,
HARNESS AS. HARNESS AS. HARNESS AS. HARNESS AS. HARNESS AS. 315C, AND 318C EXCAVATOR
A 275-6953 A 275-6873 A 275-6873
ATTACHMENT: PRODUCT LINK
A B 275-6954 B 275-6954 B 267-7958 B 275-6872 B 275-6872 A
C 259-4940 C 259-4940 C 259-4969 C 259-4940 C 259-4940 PART NUMBER: 275-6955, CHANGE: 00, VERSION: HE
Components are shown installed on a fully operable machine.
ANTENNA AS. ANTENNA AS. ANTENNA AS. ANTENNA AS. ANTENNA AS. Refer to the appropriate Service Manual for Troubleshooting, Specifications
D 266-2861 D 266-2861 D 266-2861 D 266-2861 D 266-2861 and Systems Operations.
6 5 4 3 2 1