Delta CTA ST EN

S u r g i c a l Te c h n i q u e
C T AT M
DELTA CTA™ REVERSE SHOULDER PROSTHESIS

Lateralised Cup Glenosphere Threaded Head Screw
Spherical
Head Screw
Metaglene
Epiphysis
Diaphysis
Contents
Surgical Steps 2
Introduction 3
Pre-operative Planning 4
Surgical Approach and Patient Positioning 4
Superior Lateral Approach 5
Humeral Head Resection 6
Humeral Reaming 7
Distal Humeral Reaming (Revision Surgery) 8
Proximal Reamer Guide Assembly 8
Proximal Humeral Reaming 9
Trial Humeral Implantation 10
Exposure of the Glenoid 10
Preparation of the Glenoid 11
Implantation of the Metaglene 15
Inferior and Superior Screw Placement 16
Anterior and Posterior Screw Placement 17
Trial Reduction 18
Glenosphere Placement 19
Humeral Implant Insertion 20
Hemi-arthroplasty 21
Closure 22
Post-operative Management 22
Ordering Information 23
1
Surgical Steps
Superior lateral approach Resection of the humeral head
Diaphyseal preparation Proximal reaming of the humerus
Preparation of the glenoid Preparation of the Glenoid
Metaglene Design Insertion of the Metaglene
Glenosphere Placement Insertion of the humeral Implant
2
Introduction
Anatomical Anatomical
centre of rotation centre of rotation
Medialised
centre of rotation
Figure 1 Figure 2
The Delta CTA™ Reverse Shoulder System The Delta CTA™ prosthetic geometry group to compensate for rotator cuff
is indicated for the treatment of reverses the normal relationship between deficiency, drawing the articulating
glenohumeral arthritis when it is associated scapular and humeral components, surfaces together to stabilise the joint and
with irreparable rotator cuff damage and moving the centre of rotation medially and allow as near normal function
where conventional total shoulder distally to increase the lever arm length of as possible.
arthroplasty may not be fully effective in the deltoid muscle (Figures 1 and 2).
restoring joint stability with an adequate This allows the three muscles in the deltoid
range of movement.
The design avoids high shear forces
associated with unstable conventional or
hemi-arthroplasty, that can cause the
implant to wear and loosen.
3
Pre-operative Planning Surgical Approach and Patient Positioning
Figure 3 Figure 4
An initial assessment is made of the bone The patient should be in the deck chair
in the superior and inferior aspects of the position, with the affected arm completely
glenoid, using radiographic and CT imaging free and resting on a support (Figure 4).
in order to determine the suitability of the
patient for treatment. The size of the
glenoid vault is assessed to ensure that all
four metaglene screws can be placed within
glenoid bone.
Pre-operative planning is also carried out,
using AP and lateral shoulder radiographs
of known magnification, and the available
template to confirm the size and alignment
of the implant (Figure 3).
4
Superior Lateral Approach
Figure 5 Figure 6
The quality and ease of implantation rely acromion and finishes vertically downwards The humeral head is then visible at the
on a superior lateral approach (Figure 5). A for 4 cm (Figure 6). anterior edge of the acromion – the
delto-pectoral approach is also appropriate Following subcutaneous dissection, the subacromial bursa is removed.
and the choice depends mainly on surgeon anterior and middle deltoid muscle bundles If necessary, exposure may now be
preference and clinical parameters. Revision are separated opposite the lateral margin of improved by dividing the AC ligament and
surgery for instance usually dictates a delto- the acromion, using blunt dissection (the performing acromioplasty.
pectoral approach as it allows for a longer dissection should not extend beyond 4 cm The limb is then externally rotated and the
humeral incision when faced with a from the external aspect of the acromion in head is dislocated anterosuperiorly to
difficult removal of the humeral stem. order to preserve the axillary nerve). facilitate positioning of the cutting guide. If
Used for classic rotator cuff repairs, the When the subacromial bursa is visible, the biceps is still present, it should be
superior lateral approach allows a clear gentle longitudinal traction in line with the tenodenised in the bicipital groove. Retain
visualisation of the glenoid and therefore limb will allow a retractor to be placed in the teres minor and infraspinatus when
facilitates greatly the implantation of the the subacromial space. present.
glenoid components of the prosthesis. The anterior deltoid is released
The incision is started at the level of the subperiosteally from its acromial insertion
AC joint, follows the anterior aspect of the up to the AC joint.
5
Humeral Head Resection
Orientation
Pin
Figure 8C
Epicondylar
Axis
Figure 8B
Figure 7 Figure 8A
An initial entry hole is made in the The orientation pin is then passed through cutting guide is located in the entry hole
proximal humerus using an awl. the hole in the resection and the guide is passed down the humeral
The awl tip is centred over and in line with guide corresponding to the desired canal until
the long axis of the humerus, at the retroversion (Figure 8A). Preferably, this it rests on the humeral head.
junction of the intratubercular groove and will be 0Þ since excessive retroversion will With the humeral resection guide rim
the articulating surface of the humeral head restrict joint rotation, especially in internal located on the humeral head, the
(Figure 7). rotation. Retroversion is calculated with orientation pin is aligned with the
reference to the axis of the humeral transcondylar axis (Figure 8C).
epicondyles (Figure 8B). The tip of the
6
Humeral Reaming
Figure 9 Figure 10
The humeral head resection is initiated in A forked retractor is passed under the Starting with the smallest diameter distal
line with the inferior aspect of the humeral scapula to lower the humerus. If this reamer attached to the T-Handle, the distal
cutting guide (135°), the humeral cutting provides a clear sight of the glenoid humeral canal is reamed in line with the
guide is removed and the resection surface, the resection level is correct. long axis of the humerus (Figure 10). The
completed (Figure 9). If not, a further resection may be carried final reamer should not exceed the
The initial resection removes a minimal out. templated proximal diameter (up to size 4).
amount of bone. More bone may be Reaming stops when the flange of the
removed if necessary. reamer is level with the resection.
Power reaming should not be used
to ream the humerus.
7
Distal Humeral Reaming (Revision Surgery) Proximal Reamer Guide Assembly
Figure 11 Figure 12
If a long stem is to be implanted, In addition to the reamers in the The proximal reaming guide, 36 mm or 42
150 mm and 180 mm diaphyseal revision accompanying table, 5 mm and 6 mm mm, corresponding to the templated
reamers should be used in conjunction with diameter reamers are provided as epiphysis size, is screwed to the trial
the rigid reamers that are included within start-up reamers. diaphyseal stem that matches the distal
the Delta CTA™ revision instrumentation reamer diameter. The assembly is mounted
(Figure 11). on the humeral stem impactor and
introduced in line with the long axis of the
humerus (Figure 12).
Diaphyseal references Reamer references
Size 1, length 150 mm (ref. DHR115H/DHC115B)
7.5 mm diameter (ref. ALR 075)
8 mm diameter (ref. ALR 008)
9 mm diameter (ref. ALR 009)
8
Proximal Humeral Reaming
Figure 13 Figure 14
The orientation pin is passed through the the impactor is removed, leaving the inserted more deeply to ensure that
hole in the impactor handle and reaming guide in place. the proximal reamer reaches the level of
the previously selected version angle The appropriate size of proximal humeral osteotomy.
is checked. reamer, (36.1, 36.2 or 42.2 mm) is mounted Reaming is now complete and the reamer,
The assembly is impacted into the humeral on the T-Handle. reamer guide and trial stem
canal until the appropriate mark (36 mm or The humerus is then reamed until are extracted from the humerus.
42 mm) on the impactor reaches the level of the flange of the reamer is level with the
the resection (Figure 13). osteotomy, and contact is made with
Retroversion is again checked and cortical bone (Figure 14).
If necessary, the reaming guide can be
9
Trial Humeral Implantation Exposure of the Glenoid
Figure 16
The trial epiphyseal component is attached A forked retractor is positioned on the

to the trial diaphyseal stem, and the axillary margin of the scapula, under the
assembly is mounted onto the humeral inferior glenoid labrum, to reflect the
stem impactor (Figure 15). humerus down or backward, depending on
It may be necessary to remove a wedge of the approach taken.
cortical bone to accommodate the lateral fin The labrum is excised and an extensive
on the epiphyseal component. periglenoid capsulotomy is performed. Any
The assembly is impacted into the humeral peripheral osteophytes should be removed
Figure 15 canal, ensuring the diaphyseal fin does not to restore the natural anatomic shape of the
impinge upon the lateral cortex of the glenoid
humerus. The humeral stem impactor is (Figure 16).
then removed, leaving the trial humeral
components in place.
10
Preparation of the Glenoid
Figure 17A Figure 17B
Positioning of the metaglene is important to combined with X-rays templates can lead position, the metaglene positioner will be
achieve a good, stable range of motion. to choosing a different position according used as described below.
However the position must allow the locked to the glenoid osseous state.
superior and inferior screws to be secured in Assemble the positioner by inserting the
bone. When the bone stock is sufficient, it is internal rod into the positioner handle
recommended to place the metaglene as (Figure 17B).
The metaglene positioner allows the inferior as possible on the glenoid bone in
metaglene plate position to be trialled and order to limit impingement.
screw angle checked by passing a
K-wire.
The standard position for the metaglene

central peg is posterior and inferior to the
intersection of the glenoid axes (Figure 17A).
However radiograph and CT images, In order to define the optimal metaglene
11
Figure 18 Figure 19
Then insert the hex head tip of the handle

into the plate corresponding hole (right or
left according to the operated shoulder)
and lock the assembly by screwing tightly
the internal rod (Figure 18).
Note: that the handle is angulated
by 20° relative to the plate, for
optimal visibility.
Position the plate as low as possible on the

glenoid bone. Align the vertical mark with
the glenoid pilar (Figure 19).
12
Figure 21
Figure 20
Figure 22
To ensure that the inferior metaglene screw plate upper hole etched +3 (Figure 22). This
will be fixed in good cancellous bone, will move the inferior screw superiorly to
introduce the 1.5 mm K-wire into the plate keep it within bone.
inferior hole, using a power tool. The K-
wire is directed at 17Þ angulation such as the
inferior metaglene screw (Figure 20).
If the K-wire stays within bone all along its

way, remove it and place the 2.5 mm guide
pin into the plate central hole etched +0,
using power tool (Figure 21).
If the K-wire emerges from the scapular

pilar, place the 2.5 mm guide pin into the
13
Preparation of the Glenoid Implantation of the Metaglene
Long Axis of the Glenoid

Superior Threaded
Head Screw
107Þ 34Þ
Anterior and Posterior
Spherical Head Screws
Inferior Threaded
Head Screw
Figure 24
Figure 23
Figure 24A
The glenoid reamer is attached to the sufficient depth to accommodate its

power source and the reamer pilot shaft is peripheral rim (Figure 24A). The depth
introduced into the glenoid centring hole. should be checked before implantation of
In cases of osteoporotic bone, hand the prosthesis. If sufficient peripheral depth
reaming should be used. is not achieved, the glenosphere will not
fully engage with the taper on the
Ensure that the reamer is not in contact metaglene, and further reaming should be
Leave the guide pin in place and remove with the bone before applying power since carried out until the tray is fully seated.
the metaglene positioner. Attach the this may damage the glenoid.
cannulated stop drill to the power source A revision metaglene is available and may
and drill the glenoid central hole over the The glenoid is then reamed until a smooth be selected for cases of severe erosion of
guide pin platform devoid of cartilage is created for the glenoid cavity rim.
(Figure 23). the metaglene, with
14
Implantation of the Metaglene Inferior and Superior Screw Placement
Superior
Anterior Posterior Figure 26A

Drilling of Inferior Hole
Inferior
Figure 25
The definitive Metaglene is attached the tray is impacted flat onto the prepared appropriate screw length.
to the holder, with the drill guide covering surface of the glenoid. A depth gauge is also provided. To use it,
the inferior threaded screw hole on the It is important to ensure that the the drill bush should be removed to check
implant. Check that the Metaglene is Metaglene is fully seated, flat the depth of the screw hole (Figure 26A
accurately seated on the holder. on the prepared glenoid, before it and 26B).
The assembly is inserted into the prepared is screwed into position.
glenoid with the superior and inferior holes A drill bush 2 or 2.5 mm in diameter,
aligned with the long axis of the glenoid. depending on the quality of bone,
Caution: It is imperative to use the is then inserted into the drill guide.
Metaglene holder to insert the The corresponding long drill
inferior and superior screws. (A5326/A5327) is selected, passed through
The 34° angle between these two the bush, and the inferior fixation hole is
screws is fixed and cannot be altered. drilled (Figure 25).
Once the Metaglene has been manually Laser etched depth markings on the long Threaded head screws must be used for the
aligned, the holder is tapped firmly so that drills can help when choosing the most inferior and superior holes. The spherical
15
Inferior and Superior Screw Placement
Figure 26B
Depth Measurement
Figure 28
Drilling of Superior Hole
Figure 27
Screw Placement
head screws are designed for use only with 180Þ to prepare the superior fixation hole
anterior and posterior holes. in the same way as the inferior hole.
A threaded head screw of corresponding Its depth is found and the appropriate
length to the depth found is passed threaded head screw is screwed into
through the drill guide and screwed into position (Figure 28), again ensuring it is
the inferior fixation hole. fully tightened.
The screw should be fully
tightened at this stage (Figure 27).
The Metaglene holder is then gently

detached from the bearing tray and turned
16
Anterior and Posterior Screw Placement
Figure 29 Figure 31
Anterior Hole Drilling Screw Placement
Figure 30 Figure 32
Depth Measurement Final Screw Tightening
The Metaglene holder is removed and the The anterior hole is drilled using the short A spherical head screw is introduced, and
free hand drill guide of appropriate size, 2.0 drills with depth markings (MPG020/ part tightened (Figure 31).
or 2.5 mm, is located in the anterior MPG025). The drill guide is removed and The same procedure is followed for the
fixation hole. Both anterior the hole depth found using the depth posterior screw. Both screws are then
and posterior screw positions allow gauge (Figure 30). alternately fully tightened (Figure 32).
angulation of ± 20 degrees. The drill guide
is used to set the most appropriate angle to
ensure that each screw is located in reliable
bone stock (Figure 29).
Preferential position is usually chosen by
palpating the anterior and posterior aspects
of the scapula as well as examining the X-
rays and CT scans.
17
Trial Reduction
Figure 33 Figure 34
The appropriate trial glenosphere small degree of superior lift-off is head screwdriver. In case of muscular
(36 mm or 42 mm) is attached to expected in extreme adduction overtensioning, further humeral bone
the Metaglene. The corresponding humeral (Figure 33). The lift-off will resection might be performed. Additional
cup trial is inserted disappear during the arm elevation joint stability may be achieved by
into the humeral trial assembly. thanks to the deltoid contraction introducing a retentive, more constrained
The shoulder is then reduced and assessed and the joint surface will be cup (+0 retentive, +6 retentive).
for a full range of movement. perfectly congruent (Figure 34). However those retentive cups
Soft tissue tension is correct, when: To adjust joint tensioning, the should only be used in revision
- The arm is pulled down and lateralised cup is available in three cases or to correct extreme
outward, approximately 5 mm of thicknesses (+3 mm, +6 mm, +9 mm). If instability. If the humeral cut is
humeral glenoid component further soft tissue tension is required, a +9 adequate, a lateralised cup will be
separation is expected. mm metallic humeral spacer may be put in sufficient in the majority of cases.
- The joint should remain stable when between the epiphysis and the cup. It
the arm is adducted, with no should then be attached to the trial
indication of subluxation. Only a epiphyseal component, using the hexagonal
18
Glenosphere Placement
Figure 36
Figure 35
A 1.5 mm guide pin is inserted through the The cannulated screwdriver is then
central hole of the Metaglene re-engaged and the captive screw is
(Figures 35 & 36). tightened until the glenoid bearing closes Figure 37
The 3.5 mm cannulated screwdriver is on the taper of the bearing tray.

engaged in the definitive Glenosphere and Further impaction of the junction is then
guided over the 1.5 mm guide pin. obtained by gently tapping the glenosphere
After two or three turns, the cannulated using the glenosphere impactor and
screwdriver is disengaged and the glenoid tightening again the glenosphere central
bearing is checked to ensure that it is screw.
properly aligned. Care should be taken to ensure that the
glenoid bearing is fully locked onto the
bearing tray (Figure 37).
19
Humeral Implant Insertion
Figure 39
The trial humeral assembly is extracted into the

from the humerus. The corresponding humeral canal.
Figure 38 definitive humeral epiphyseal component is If the implant is to be cemented,
attached to the impactor (Figure 38). The a synthetic cement restrictor or bone plug
definitive diaphyseal component is screwed is introduced into the distal humeral canal
to the epiphyseal component. The two to restrict the passage of cement. Cement is
components are then locked tight, using the injected into the humeral canal and, when
wrench and driver (Figure 39). the cement is at its appropriate viscosity,
It is important to ensure the two the implant assembly is introduced in line
components are tightly locked together to with the long axis of the humerus and in
reduce the chance of post operative the chosen version angle. Pressure is
disassembly. maintained on the introducer until the
If cementless components are selected, the cement is fully polymerised.
assembly is introduced in the appropriate
retroversion and the assembly is impacted
20
Humeral Implant Insertion Hemi-arthroplasty
Standard
+4 mm Offset
Figure 41
Figure 40 Figure 42
The definitive humeral cup is impacted In cases of intra-operative fracture

using the cup impactor (Figure 40). of the glenoid cavity, or revision of
The joint is reduced and a final assessment the Delta CTA™ glenoid, for example,
of joint stability and range of movement is a hemi-arthroplasty may be considered.
carried out. Intermediate metallic heads are provided
within the Delta CTA™ system to complete
this procedure.
Two epiphyseal diameters, 36 and 42 mm, are
available in standard and + 4 mm offset
(Figure 41). The hemi heads can be
assembled either directly onto the epiphysis
or onto the metallic spacer.
These should be introduced using the
humeral head impactor (Figure 42).
21
Closure Post-operative Management
Once the joint space is irrigated and cleared Appropriate post-operative physiotherapy is arm to eat and write but should not raise the
of debris, the anterior deltoid an important factor in the outcome of this arm. In conjunction with these exercises for
is firmly sutured at the fibrous acromial procedure, since stability and mobility now scapulohumeral recovery, it is important to
perimeter or using transosseous stitches. A depend on the deltoid alone. The strengthen muscle connection with the
drain is left in place. physiotherapy programme, which should be scapula
Layered closure of the soft tissues normally planned to suit the individual patient, in order to facilitate muscle and implant
leads to an adequate range consists of two phases: early (6 weeks) and function. Passive exercise in the swimming
of motion, without instability. late. pool is recommended as soon as scars begin
Two days after the operation the patient can to form.
be mobile. This early phase is dedicated to After the sixth or seventh week, active
gentle and gradual recovery of the passive strengthening movements may be gradually
range of shoulder motion: abduction of the added to the programme. These exercises,
scapula, anterior elevation and medial and which closely follow everyday activities, are
lateral rotation. An abduction cushion may performed in a sitting or standing position,
be used to relieve pressure on the deltoid. using conventional methods, with isometric
Physiotherapy is mainly performed with the exercises and resistance movements
patient supine, passive and with both hands becoming increasingly important.
holding a bar that is manipulated by the A series of exercises for rhythmic
contralateral hand, as described stabilisation of the upper arm as well
by Neer. as eccentric working on lowering the arms
The patient is encouraged to use the affected complete the strengthening of
the muscles. Physiotherapy should
be performed over a period of at least
six months.
22
Implants
EHC361B Cemented Humeral Epiphysis, 36.1

EHR361H Cementless Humeral Epiphysis, 36.1

DHC010B 85mm Cemented Humeral Diaphysis, Size 0

DHR000H 95mm Cementless Humeral Diaphysis, Size 0

4CHL336 Lateralised Humeral Cup, ø36, + 3 mm

4CHS036R Medialised Retentive Humeral Cup, ø36, + 0 mm/ R

4CHS042R Medialised Retentive Humeral Cup, ø42, + 0 mm/ R
4CHL636R Lateralised Retentive Humeral Cup, ø36, + 6 mm/ R
4CHL642R Lateralised Retentive Humeral Cup, ø42, + 6 mm/ R
RTH236 Humeral Spacer, ø36, + 9 mm

RTH242 Humeral Spacer, ø42, + 9 mm
TIH036 Humeral Head, ø36, + 0 mm

MGC002H Standard Metaglene
GSC236 Glenosphere Dia. 36 mm

GSC242 Glenosphere Dia. 42 mm
VFM4524 Metaglene Screws, Dia. 4.5 x 24 mm (Threaded Head)

VSM4518 Metaglene Screws, Dia. 4.5 x 18 mm (Spherical Head)
23
Humeral Preparation Instruments
GSH002 Humeral Resection Guide
ARR001 Orientation Pin
FPH361 Proximal Humeral Reamer, 36.1

FDH036N Distal Humeral Reamer, Size 0, Dia. 36 mm

FDH136 Distal Humeral Reamer, Size 1, Dia. 36 mm
ITH003 Humeral Stem Impactor
EHF001 Forked Retractor
EHF002 Forked Retractor Large
GFP136 Proximal Reamer Guide, Dia. 36 mm

GFP142 Proximal Reamer Guide, Dia. 42 mm
IGF004 Reamer Guide Impactor/Extractor
CLE014 Diaphyseal Stem Locking Wrench
DHF010N Humeral Diaphysis Trial, Size 0

DHF110 Humeral Diaphysis Trial, Size 1
EHF361 Humeral Epiphysis Trial, 36.1

REH236 Humeral Spacer Trial, ø36, + 9 mm
REH242 Humeral Spacer Trial, ø42, + 9 mm
A5469 Lateralised Humeral Cup Trial, ø36, + 3 mm

A5265 Medialised Retentive Humeral Cup Trial, ø36, + 0 mm / R

A5262 Medialised Retentive Humeral Cup Trial, ø42, + 0 mm / R
A5263 Lateralised Retentive Humeral Cup Trial, ø36, + 6 mm / R
A5260 Lateralised Retentive Humeral Cup Trial, ø42, + 6 mm / R
TEH036 Humeral Head Trial, ø36, + 0 mm

24
Glenoid Preparation Instruments
A5266 Guide Pin, Dia. 2.5 mm
A5267 Cannulated Stop drill
A5075 Glenoid Surfacing Rasp, Dia. 36 mm

A5076 Glenoid Surfacing Rasp, Dia. 42 mm
PAM001 T-Handle
A5271 Drill Bush, Dia. 2.0 mm

A5272 Drill Bush, Dia. 2.5 mm
GPM020 Drill Guide, Dia. 2.0 mm

GPM025 Drill Guide, Dia. 2.5 mm
A5326 Long S/I Drill Bit, Dia. 2.0 mm (170 mm Length)

A5327 Long S/I Drill Bit, Dia. 2.5 mm (170 mm Length)
MPG020 Short A/P Drill Bit, Dia. 2.0 mm (100 mm Length)

MPG025 Short A/P Drill Bit, Dia. 2.5 mm (100 mm Length)
A5273 Glenosphere Trial, Dia. 36 mm

A5274 Glenosphere Trial, Dia. 42 mm
9E03011 3.5 mm Hex. Head Screwdriver, Cannulated
A5307 Screw Depth Gauge
PRT001 Standard Impactor Holder
EPT001 Humeral Head Impactor

EPC032 Humeral Cup Impactor
A5074 1.5 mm Guide Wire
A5268 Metaglene Holder
A5470 Metaglene positioner plate
A5471 Metaglene positioner handle
A5472 Internal rod for metaglene positioner
9375 15 150 K-wire Dia. 1.5mm length 150 mm
Trays
A5807 Glenoid Tray Base
A5831 Upper glenoid tray
A5812 Glenoid Tray Lid
A5815 Glenoid Tray Screw Rack
A5809 Humeral Tray 1 Base

A5808 Humeral Tray 1 Insert
A5813 Humeral Tray 1 Lid
A5811 Humeral Tray 2 Base

A5810 Humeral Tray 2 Insert
A5814 Humeral Tray 2 Lid
A5819 Tray Insert for Cups
25
Delta CTA™ Revision
Implants
DHC115B 150 mm Revision Cemented Humeral Diaphysis, Size 1
DHR115H 150 mm Revision Cementless Humeral Diaphysis, Size 1

MRC002H Revision Metaglene
Instruments
ETH001 Standard Humeral Prosthesis Extractor
MDE001 Extraction Rod
MAI001 Slap Hammer
ITH003 Stem Extractor
TEP035 3.5 mm Hex. Head Screwdriver
TEP025 2.5 mm Hex. Head Screwdriver
ALR005 Diaphyseal Reamer, Dia. 5 mm
ALR075 Diaphyseal Reamer, Dia. 7.5 mm
DHF115 150 mm Long Humeral Diaphysis Trial, Size 1

A5288 Metaglene Extractor
Trays
A5280 Tray Base
A5281 Tray Insert
A5279 Lid
26
Notes
27
28
References
1. Seebauer L. Biomechanical classification of cuff tear 17. Renaud P, Wahab H, Bontoux L, Dauty M, Richard I,
arthropathy. Global Shoulder Society Meeting, Salt Lake Bregeon C. Total inverted shoulder prosthesis and rotator
City, UT, USA, July 17-19,2003 (abstract). cuff insufficiency: evaluation and determination of
anatomical parameters predictive of good functional
2. Constant CR, Murley AHG. A clinical method of outcome in 21 shoulders. Ann Readapt Med Phys
functional assessment of the shoulder. Clin Orthop 2001;44:273-280.
1987;214:160-164.
18. Rittmeister M, Kerschbaumer F. Grammont reverse total
3. Ekelund A, De Wilde L, Seebauer L, Nerot C, Capon D, shoulder arthroplasty in patients with rheumatoid arthritis
Valenti P. Clinical results of the reversed delta shoulder and nonreconstructible rotator cuff lesions. J Shoulder
arthroplasty: A multicentre study with minimum 5 years Elbow Surg 2001;10:17-22.
follow-up. 17th Congress of the European Society for
Surgery of the Shoulder and the Elbow (ESSSE/SECEC), 19. Seebauer L, Keyl W. Treatment of cuff tear arthropathy with
Heidelburg, Germany, 24-27 September, 2003 (poster). an inverted shoulder prosthesis (Delta III® – Grammont).
Presented at the 8th International Conference on Surgery
4. Jacobs R, Debeer P, De Smet L. Treatment of rotator cuff of the Shoulder, Cape Town, South Africa, April, 2001
arthropathy with a reversed Delta shoulder prosthesis. Acta (abstract).
Orthop Belg 2001;67:344-347.
20. Sperner G, Kralinger F, Golser K, Smekal V. First
5. Sirveaux F, Favard L, Oudet D, Huquet D, Walch G, Molé D. experiences with the Delta III Inversprosthesis. Presented
Grammont inverted total shoulder arthroplasty in the at the 8th International Conference on Surgery of the
treatment of glenohumeral osteoarthritis with massive Shoulder, Cape Town, South Africa, April, 2001 (abstract).
rupture of the cuff. Results of a multicentre study of 80
shoulders. J Bone Joint Surg Br 2004;86B:388-395. 21. Valenti P, Sbihi A. Inverted Delta 3 prosthesis in
nonreconstructable rotator cuff lesions: report of 25 cases.
6. Valenti PH, Bouttens D, Nerot C. Delta 3 reversed Presented at the 8th International Conference on Surgery
prosthesis for osteoarthritis with massive rotator cuff tear: of the Shoulder, Cape Town, South Africa, April, 2001
long term results (>5 years). In: Walch G, et al., ed. 2000 (abstract).
Shoulder prostheses... two to ten year follow-up.
SaurampsMedical; 2001:253-259. 22. Delloye C, Joris D, Colette A, Eudier A, Dubuc JE.
Mechanical complications of total shoulder inverted
7. Grammont PM, Baulot E. Delta shoulder prosthesis for prosthesis. Rev Chir Orthop Reparatrice Appar Mot
rotator cuff rupture. Orthopedics 1993;16:65-68. 2002;88:410-414.
8. Baulot E, Chabernaud D, Grammont PM. Results of 23. De Wilde LF, Van Ovost E, Uyttendaele D, Verdonk R.
Grammont’s inverted prosthesis in omarthritis associated Results of an inverted shoulder prosthesis after resection
with major cuff destruction. Apropos of 16 cases. Acta for a tumour of the proximal humerus. Rev Chir Orthop
Orthop Belg 1995;61 (Suppl 1):112-119. Reparatrice Appar Mot 2002;88:373-378.
9. Habermeyer P. Open treatment of rotator cuff lesions. 24. Meskens M, Broos P. Massive rotator cuff tears with
Orthopade 1995;24:512-528. pseudoparalysis and rotator cuff arthropathy treated by the
10. De Buttet M, Bouchon Y, Capon D, Delfosse J. Grammont reversed delta prosthesis. Tijdschrift voor Geneeskunde
shoulder arthroplasty for osteoarthritis with massive rotator 2002;58:331-337.
cuff tears – report of 71 cases. J Shoulder Elbow Surg 25. De Wilde LF, Audenaert EA. A comparative biomechanical
1997;6:197 (abstract 14). analysis of ten different prosthesis for rotator cuff tear
11. Cazeneuve JF, Saltanov I. Reverse total shoulder arthroplasty. Société Européenne de Chirurgie de l’Epaule
arthroplasty (GRAMMONT’S arthroplasty) for acute et du Coude (SECEC), Heidelberg, Germany, 24-27
complex fractures of proximal humerus. Five years September, 2003 (abstract).
experience. Société Européenne de Chirurgie de l’Epaule et 26. Gilbart MK, Pirkl C, Gerber C. Complications associated
du Coude (SECEC), Oulu, Finland, June, 1998 (abstract). with the delta III reverse ball-and-socket shoulder
12. Cazeneuve JF, Dang VB, Zanfonhouede T. A six year prosthesis. Société Européenne de Chirurgie de l’Epaule et
experience of reverse total shoulder arthroplasty du Coude (SECEC), Heidelberg, Germany, 24-27
(GRAMMONT’S arthroplasty) in elderly population for four- September, 2003 (abstract).
part fractures of the proximal humerus. European 27. Julien Y, Gondrand I, Charpenay C, Devilliers L, Baulot E,
Federation of the National Association of Orthopaedics and Trouillod P. Shoulder reconstruction using Grammont
Traumatology Congress, Brussels, Belgium, June, 1999 (Delta III) total arthroplasty after resection for malignant
(abstract). bony tumours of proximal humerus. Eur J Orthopaed Surg
13. Cazeneuve JF, Kermad F. Grammont’s arthroplasty for acute Traumatol 2003;13:77-79.
complex fractures of proximal humerus in elderly 28. Postacchini F, Gumina S, De Santis P, et al. Cuff tear
population: six year experience. Société Européenne de arthropathy: mid term outcomes with riverse prosthesis.
Chirurgie de l’Epaule et du Coude (SECEC), The Hague, Société Européenne de Chirurgie de l’Epaule et du Coude
The Netherlands, 1999 (abstract). (SECEC), Heidelberg, Germany, 24-27 September, 2003
14. De Wilde L, Mombert M, Van Petegem P, Verdonk R. (abstract).
Revision of shoulder replacement with a reversed shoulder 29. Sirveaux F, Roche O, Raphoz AL, Gosselin O, De Gasperi M,
prosthesis (Delta III®): report of five cases. Acta Orthop Mole D. Hemiarthroplasty versus inversed prosthesis in the
Belg 2001;67:348-353. treatment of proximal humerus fractures: a prospective
15. Gerber A, Roache P, Gerber C. The Delta III reversed randomized study in the elderly. Société Européenne de
prosthesis: weapon of the devil or acceptable salvage Chirurgie de l’Epaule et du Coude (SECEC), Heidelberg,
procedure? Presented at the 8th International Conference Germany, 24-27 September, 2003 (abstract).
on Surgery of the Shoulder, Cape Town, South Africa, April, 30. Woodruff MJ, Cohen AP, Bradley JG. Arthroplasty of the
2001 (abstract). shoulder in rheumatoid arthritis with rotator cuff
16. Handelberg FWJ. Treatment options in full thickness rotator dysfunction. Int Orthop 2003;27:7-10.
cuff tears. Acta Orthop Belg 2001;67:110-115.
This publication is not intended for distribution in the USA.
Delta CTA™ is a trademark of DePuy Orthopaedics, Inc.

© 2005 DePuy International Limited. All rights reserved.
Cat No: 9072-78-032
DePuy International Ltd Manufactured by

St Anthony’s Road DePuy France SA
Leeds LS11 8DT 7 Allée Irène Joliot Curie
England BP 256 0459
Tel: +44 (113) 387 7800 69801 Saint Priest Cedex
Fax: +44 (113) 387 7890 France
Tel: +33 4 72 79 27 27
Fax: +33 4 72 79 28 28
Revised: 08/05

Delta CTA ST EN

Uploaded by

Copyright:

Available Formats

Delta CTA ST EN

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Delta CTA ST EN

Uploaded by

Copyright:

Available Formats

S u r g i c a l Te c h n i q u e

DELTA CTA™ REVERSE SHOULDER PROSTHESIS

Surgical Approach and Patient Positioning 4

Superior Lateral Approach 5

Humeral Head Resection 6

Distal Humeral Reaming (Revision Surgery) 8

Proximal Reamer Guide Assembly 8

Proximal Humeral Reaming 9

Trial Humeral Implantation 10

Exposure of the Glenoid 10

Preparation of the Glenoid 11

Implantation of the Metaglene 15

Inferior and Superior Screw Placement 16

Anterior and Posterior Screw Placement 17

Humeral Implant Insertion 20

Diaphyseal preparation Proximal reaming of the humerus

Preparation of the glenoid Preparation of the Glenoid

Metaglene Design Insertion of the Metaglene

Glenosphere Placement Insertion of the humeral Implant

The trial epiphyseal component is attached A forked retractor is positioned on the

Figure 17A Figure 17B

The standard position for the metaglene

Then insert the hex head tip of the handle

Position the plate as low as possible on the

If the K-wire stays within bone all along its

If the K-wire emerges from the scapular

Long Axis of the Glenoid

The glenoid reamer is attached to the sufficient depth to accommodate its

Anterior Posterior Figure 26A

The Metaglene holder is then gently

The 3.5 mm cannulated screwdriver is on the taper of the bearing tray.

The trial humeral assembly is extracted into the

The definitive humeral cup is impacted In cases of intra-operative fracture

EHC361B Cemented Humeral Epiphysis, 36.1

EHR361H Cementless Humeral Epiphysis, 36.1

DHC010B 85mm Cemented Humeral Diaphysis, Size 0

DHR000H 95mm Cementless Humeral Diaphysis, Size 0

4CHL336 Lateralised Humeral Cup, ø36, + 3 mm

4CHS036R Medialised Retentive Humeral Cup, ø36, + 0 mm/ R

RTH236 Humeral Spacer, ø36, + 9 mm

TIH036 Humeral Head, ø36, + 0 mm

MGC002H Standard Metaglene

GSC236 Glenosphere Dia. 36 mm

VFM4524 Metaglene Screws, Dia. 4.5 x 24 mm (Threaded Head)

GSH002 Humeral Resection Guide

ARR001 Orientation Pin

FPH361 Proximal Humeral Reamer, 36.1

FDH036N Distal Humeral Reamer, Size 0, Dia. 36 mm

ITH003 Humeral Stem Impactor

EHF001 Forked Retractor

EHF002 Forked Retractor Large

GFP136 Proximal Reamer Guide, Dia. 36 mm

IGF004 Reamer Guide Impactor/Extractor

CLE014 Diaphyseal Stem Locking Wrench

DHF010N Humeral Diaphysis Trial, Size 0

EHF361 Humeral Epiphysis Trial, 36.1

A5469 Lateralised Humeral Cup Trial, ø36, + 3 mm

A5265 Medialised Retentive Humeral Cup Trial, ø36, + 0 mm / R

TEH036 Humeral Head Trial, ø36, + 0 mm