GH5200

Tracker for lone worker protection Quick Manual

v1.0
Table of Contents
Know your device .......................................................................... 3

Set up your device ......................................................................... 4

How to insert Micro-SIM card and connect the battery ................ 4

PC Connection (Windows) ................................................................ 5

How to install USB drivers (Windows)............................................. 5

Configuration (Windows) ................................................................. 5

Quick SMS configuration .................................................................. 7

LED indication scenarios .............................................................. 8

Characteristics............................................................................... 9

Basic characteristics ......................................................................... 9

Safety information ...................................................................... 10

Certification and Approvals ....................................................... 11

Warranty ...................................................................................... 12

Warranty Disclaimer ....................................................................... 12

2 GH5200 | Quick Manual

Know your device

Figure 1 GH5200 device view

3 GH5200 | Quick Manual

Set up your device
How to insert Micro-SIM card and
connect the battery
1. Remove the cover.
2. Insert Micro-SIM card as shown with PIN request disabled.
Make sure that Micro-SIM card cut-off corner is pointing
forward to slot.
3. Insert the battery as shown to device. Position the battery in
place where it does not obstruct other components.
4. Reattach the cover and tighten the screw.

Figure 2 Remove the cover Figure 3 Insert Micro-SIM card Figure 4 Insert the battery Figure 5 Reattach the cover and tighten the
screw

4 GH5200 | Quick Manual

PC Connection (Windows) Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
1. Turn on your device by holding the power button for around 7
seconds.
2. Connect device to computer using Micro-USB cable or
Bluetooth connection:
Configuration (Windows)
• Using Micro-USB cable At first GH5200 device will have default factory settings set. These
▬ You will need to install USB drivers, see “How to install settings should be changed according to the user's needs. Main
USB drivers (Windows)” configuration can be performed via Teltonika Configurator
• Using Bluetooth software. Configurator operates on Microsoft Windows OS and
▬ GH5200 Bluetooth is enabled by default. Turn on uses prerequisite MS .NET Framework. Make sure you have the
Bluetooth on your PC, then select Add Bluetooth or correct version installed.
other device > Bluetooth. Choose your device named –
Table 1 MS .NET requirements
“GH5200_last_7_imei_digits”, without LE in the end.
Enter default password 5555, press Connect and then MS .NET requirements
select Done. Operating MS .NET Framework
Version Links
3. You are now ready to use the device on your computer. system version
Windows Vista
Windows 7 MS .NET Framework
How to install USB drivers Windows 8.1
Windows 10
4.6.2
32 and 64 bit www.microsoft.com

(Windows) Downloaded Configurator will be in compressed archive. Extract it

and launch Configurator.exe. After launch software language can
1. Please download COM port drivers from here.
be changed by clicking in the right bottom corner (Figure 6
2. Extract and run TeltonikaCOMDriver.exe.
Language selection).
3. Click Next in driver installation window.
4. In the following window click Install button.

5 GH5200 | Quick Manual

 Various Status window tabs display information about GNSS,
GSM, I/O, Maintenance and etc. GH5200 has one user editable
profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
Figure 6 Language selection
functionality:
Configuration process begins by pressing on connected device
(Figure 10 Device connected via USB). 1. Load from device – loads configuration from device.

2. Save to device – saves configuration to device.

3. Load from file – loads configuration from file.

4. Save to file – saves configuration to file.

Figure 7 Device connected via USB
5. Update firmware – updates firmware on device.
After connection to Configurator Status window will be displayed
(Figure 8 Configurator Status window). 6. Read records – reads records from the device.

7. Reboot device – restarts device.

8. Reset configuration – sets device configuration to

default.

Most important configurator section is GPRS – where all your

server and GPRS settings can be configured and Data Acquisition
– where data acquiring parameters can be configured.

Figure 8 Configurator Status window

6 GH5200 | Quick Manual

 Default configuration settings
Quick SMS configuration Movement detection:
Default configuration has optimal parameters present to ensure Movement will be
best performance of track quality and data usage. detected by
accelerometer
Quickly set up your device by sending this SMS command to it:
Device makes a record On Moving if one of these events happen:
" setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006;0"
300 seconds passes Device turns 10 degrees
Note: Before SMS text, two space symbols should be inserted.
Speed difference
GPRS settings:
Traveled distance is between last coordinate
• 2001 – APN more than 100 meters and current position is
• 2002 – APN username (if there greater than 10 km/h
are no APN username, empty Device makes a record On Stop if:
field should be left) 1 hour passes while
• 2003 – APN password (if there device is stationary
are no APN password, empty
Records sending to server:
field should be left)
If device has made a
Server settings: record it is sent to the
• 2004 – Domain server every 120
seconds
• 2005 – Port
• 2006 – Data sending protocol
After successful SMS configuration, GH5200 device will
(0 – TCP, 1 – UDP)
synchronize time and update records to configured server.
Time intervals and default I/O elements can be changed by using
Teltonika Configurator or SMS parameters.

7 GH5200 | Quick Manual

LED indication scenarios
A button was triggered with configured
Keyboard Action Activated
function to activate functionality
A button was triggered with configured
Keyboard Action Deactivated
function to deactivate functionality
Table 3 LED indication scenarios
Battery INDICATION
SCENARIO MEANING Charging Device is charging
GSM INDICATION Fully Charged Device is fully charged
SIM is not inserted, failed to connect to Charging Error An error occurred while charging
GSM Error GSM operator or GSM signal is being Battery Low Device battery is low
jammed
Device is trying to register to GSM Default configuration LED indications
GSM Registering
network
SMS Send/Receive SMS is received or sent Table 4 Default configuration LED indications
Incoming Call Device notices incoming call
Call Active A call is in progress SCENARIO LED, COLOR & Additional indication
Outgoing Call Device notices outgoing call GSM Error GSM
Incoming Call Device notices incoming call
Call Active GSM
GNSS Indication
No GPS Fix GNSS
No GNSS Fix Device searches for valid GNSS fix
GNSS Fix Device has valid GNSS fix GPS Fix GNSS

EVENT INDICATION Device Off Battery, Vibration

Event Eventual record is saved Device On Battery, Vibration
Panic Event Panic record is saved
I Am Alive GNSS
Device Off Device is turning off
Device On Device is turning on Charging Battery
Indication when Man-down Fully Charged Battery
Pre Alarm functionality starts counting timeout
Charging Error Battery
till event
Man-down Man-down is active Battery Low Battery
I Am Alive Periodical indication that device is on
Sleep Mode Device is in sleep mode Note! Two LED colors are available – Green and Red. Indications
Indication when one of device’s are fully customizable depending on the user needs.
Key Pressed
buttons is pressed

8 GH5200 | Quick Manual

Characteristics Bluetooth
Specification 4.0 + LE
Supported peripherals Headset
Interface
Basic characteristics Configurable buttons
GNSS antenna
5
Internal High Gain
GSM antenna Internal High Gain
Table 5 Basic characteristics
USB 2.0 Micro-USB
LED indication 3 LEDs
Module
SIM Micro-SIM, eSIM possibility
Name TM2500
Memory 128MB internal flash memory
Technology GSM, GPRS, GPS, BLUETOOTH
Physical specification
GNSS Dimensions 93 x 64 x 10 mm (L x W x H)
GPS, GLONASS, GALILEO, BEIDOU, Weight 80 g
GNSS
SBAS, QZSS, DGPS
Operating environment
Receiver 33 channel
Operating temperature -25 °C to +65 °C
Tracking sensitivity -165 dBM
Storage temperature -25 °C to +85 °C
Accuracy <3m Operating humidity 5% to 95% non-condensing
Hot start <1s Ingress Protection Rating IP41
Warm start < 25 s Features
Cold start < 35 s Sensors Accelerometer
Cellular Overspeeding, Man-down, Alarm, Auto
Technology GSM Scenarios Geofence, Manual Geofence, Action on
call
Quad-band 850 / 900 / 1800 / 1900
2G bands GPS Sleep, Online Deep Sleep, Deep
MHz Sleep modes
Sleep, Ultra Deep Sleep
GPRS Multi-Slot Class 12 (up to 240
Data transfer FOTA Web, FOTA, Teltonika
kbps), GPRS Mobile Station Class B
Configuration and firmware update Configurator (USB, Bluetooth), FMBT
Data support SMS (text/data) mobile application (Configuration)
Power SMS Configuration, Events, Debug
Charging voltage 5V DC with over-voltage protection GPRS commands Configuration, Debug
Time Synchronization GPS, NITZ, NTP
Battery 1050 mAh Li-Ion battery

9 GH5200 | Quick Manual

Safety information In order to prevent device from mechanical
damage it is advisable to transport it in a shock-
resistant packaging. If device stopped working
This message contains information on how to operate GH5200
properly regardless of the settings only a
safely. By following these requirements and recommendations,
qualified specialist can help.
you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the Operate the device in suitable conditions. Do not
device! use the device where mobile connectivity is
forbidden.
Use only original batteries. Using uncertified
manufacturer or different type batteries may
Road safety first. Comply with local traffic laws,
cause an explosion.
always hold you hands on a steering wheel when
Use batteries safely. Protect batteries from using a device. Your safety is of utmost
moisture, place them in a cool and dry place when importance when you drive.
storing. Avoid extensive operation at high
temperatures. Do not attempt charging battery All wireless devices are sensitive to
directly from the electrical mains. All utilized electromagnetic interference, as a result wireless
batteries shall comply with IEC 62133. devices affect the performance of each other.
Power supply circuits used to charge the device
connection must have safeguards, which prevent Charging precautions. SELV LPS chargers, personal
power leakage, short circuits or incorrect computers or laptops that device will be
electrical grounding. Any used switches ought to connected to must comply with the requirements
be installed in a readily accessible location. Power of IEC 60950:2005 standard.
must be uninterrupted.
Remove device safely. Device must be
disconnected from computer or charger by
unplugging the magnetic USB cable from the
device.

10 GH5200 | Quick Manual

Certification and Approvals
• GH5200 CE RED - Pending
• GH5200 SAR - Pending

This sign on the package means that it is

necessary to read the User‘s Manual before
you start using the device.

This sign on the package means that all used

electronic and electric equipment should not
be mixed with general household waste.

Hereby, Teltonika declare under our sole

responsibility that the above described
product is in conformity with the relevant
Community harmonization: European
Directive 2014/53/EU (RED).

11 GH5200 | Quick Manual

Warranty Warranty Disclaimer
TELTONIKA guarantees its products to be free of any TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS
manufacturing defects for a period of 24 months. With additional WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS
agreement we can agree on a different warranty period, for more THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL
detailed information please contact our sales manager. IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY
EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY
Contact us teltonika.lt/company/contacts ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE,
All batteries carry a reduced 6 month warranty period.
LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC
If a product should fail within this specific warranty time, the LOSS.
product can be:
More information can be found at teltonika.lt/warranty-repair
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same
functionality
• TELTONIKA can also repair products that are out of warranty at
an agreed cost.

12 GH5200 | Quick Manual