Scribd
Upload
141 views

EmbeddedC Interview

The document contains questions asked by different companies during interviews for embedded positions. The questions cover a wide range of embedded topics including microcontroller architectures, communication protocols, real-time systems, debugging techniques, and specific questions about projects and experience.

Uploaded by

aravind
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
141 views

EmbeddedC Interview

The document contains questions asked by different companies during interviews for embedded positions. The questions cover a wide range of embedded topics including microcontroller architectures, communication protocols, real-time systems, debugging techniques, and specific questions about projects and experience.

Uploaded by

aravind
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

-ARI

1.What are the commands used in GSM/


2.In SIM900A

900 what and which frequency?

3.Explain about UART?

4.How to calculate baud rate and its equation?

5.What is the bus arbitration in I2C?

6.How many slaves will handle(i2c)?

6.What is the size of message(bytes)?

ARI

1.Explain any 4 previous projects?(not in resume)


2.Explain about ADC?

3.Explain about Ultrasonic sensor?

4. What are the problems you got in your projects?

BOSCH
1.On what basis 4bit ,8bit,16bit ,32bit Microcontrollers are differentiate?

2.How to interface LM35 to 8052 or ARM7/

3.How to interface accelerometer ?

4.How to dump .hex file in controller? is it is possible to store some other area.

5.What is the difference between product specification and technical specification/

6.What is CAN protocol? It is used in your project?

7.what are the coding guidelines used for developing an embedded projects?

8.What are the GSM commands used in your projects ?Explain AT commands?

9.What are the interrupts in 8051?


8.What are the problems faced in GSM&GPS, mostly you put in your resume?

9.What is white box testing?

10.what is GSM frequency(sim900)

INVENTECH

1.What is Embedded C?
2.What is return type of ISR?

3.Can we use any function inside ISR?

4.Why we use RTOS concept in embedded system?

5.Difference between soft-real-time and Hard-real-time?

6.What is real time and what is RTOS?

TECH MAHINDRA

1.Expalin UART& USART?

2.Explain I2C frame formate?

3.How many slaves I2C can handle?

VALEO

1.What are the data types used in embedded c?

2.Difference between CISC & RISC?

3.Difference between hard & soft real-time?

4.How you will find processor is Little endean or Big endean?

5.What is the better loop for infinity loop in embedded C?

6.Difference between cortex M0,M1,M2,M3.

7.What is Thumb rule& Thumb-2 rule?

8.If you buy any embedded product ,what are the features look in it ?

9.Can we use other languages instead of ‘c’ in embedded systems?

10.What are the commonly found errors in embedded systems?


11.What is the difference between hardware design & software design?

12.Timers works in microprocessors count or down count?

13.What are the different types of systems involved in embedded systems?

14.What are the different types of basics used by the embedded system.

15.What is the difference between polling method & interrupt method?

16.How much time is required for an instruction execute in 8051?

17.Explin about ISR?

18.Explain the protocol used in your project?

19.Write a program using interrupt in 8051 or arm7.

20.With 1 switch 2 led’s each led should toggle with different time period like led1 with

1sec & led2 with 2sec using timers not delay functions.

VIZZITECH SOLUTIONS

1.Data types used in embedded c programming?

2.It is necessary to start program with main()?

3.CAN protocol and uses?

4.Difference between UART & RS232

5.Testing methods? white box testing and block box testing.

6.Difference between SPI &I2C?

7.How to interface controller to gsm?

8.Commands used in your project to communicate?(gsm)

9.What is embedded systems?

10.Difference between C and embedded C?

11.Busses used for communication in your project?

12.Various timers in Embedded?

13.What is what dog timer?


14.Commonly found errors in embedded systems?

15.SPI is an interface protocol? Uses of spi.

16.Cortext M3 features?

17.Uses of RICS architecture in OS?

18. Use of boot loader?

19.How to verify problems in hardware ?

20.Difference between latches and flipflop?

21.Use of RFID in your project?

22.What is IOT? Challenges in IOT?

XPETIZE technology solutions pvt.ltd

1.Explain about watch dog timer?

2.How do you use Oscilloscope, Logic analyzer, Spectrum analyzer?

3.Why did you chose that controller for your project, surly not other one?

4.How will you debug a program ?

5.Expalin about PWM technique in embedded system?

6.How ADC works?

7.Explain about accelometer?

8.Explain I2C,SPI,CAN,LIN,UART concepts?

9.When do we need os in embedded systems?

10.Can we use printf instead of ISR?

11.Difference between Harvard and von-Newman n architecture ?

12.What is IO mapped IO and memory mapped IO?

13.Difference between IO mapped IO and memory mapped IO?

14.In today world which programming language are used in embedded systems and why?

15.What are the challenges over come in your project?

16.what is meant by firmware?


17.How do you find which programming language is portable & efficient for embedded system.

18.What is fan-in and fan-out?

19.Use of JTAG?

20.What is Tristate logic?

21.Name some commands you used in Linux? (linux)

/* automotive robotics on 22-01-2017 */

1.how to build os in to arm board

2.how to build device tree in to board

/* Globaledge telephonic interview on 15-02 */

1.how i2c works and its frame format.

/*-----------------------*/

1. LM35.

2.Explain PWM.

3.8051 Timer modes.

4.7-Segment display,Lcd 8/4 bit operation.

5. In LDR what is the resistance value,when light is comes to that sensees.

6.Which is RTC numbers.

7.Difference between Microprocessser and Microcontroller.

8.SPI, I2C operation.

9.How to find Arry size & Structure size.

10.EPROM how to read data from. Data to that one.

11.Explain PIC,8051 ports & ADC full scale value.


12.RS232,RS428 range of difference.

/* unik system on 07-02 */

1.how i2c works.frame formate.

/*libsys*/ telephonic

1.Difference between PIC and LPC2148 microcontrollers.

2.Protocalls UART, SPI, I2C.

3.Explain about your projects.

4. What is GSM module and explain it?

5.What s ment by RFID.

6.What is compiler?

7.Which compilers ID's are used for your projects?

/*votray tech*/

1.What is UART,RS232 standards?

2.What is I2C and explain it?

3.How many slaves can I2C handles?

4.Why I2C &SPI invented? Which protocal is most usefull?

5.Explain about your projects?

6.What is GSM and protocal used for that?

7.What is ADC and explain it?

8.What is stm32 and explain it. why it is used?

You might also like