DV382H.392H-E.

BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 1

ENGLISH

DVX382H / DVX392H

FOR THE GUARANTEE TERMS & CONDITIONS,

PLEASE REFER TO BACK COVER OF THIS MANUAL.

P/No. : MFL56732723
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 2

Safety Precaution
Protect the power cord from physical or mechanical abuse, such as being twisted,
CAUTION kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,
RISK OF ELECTRIC SHOCK wall outlets, and the point where the cord exits the appliance.
DO NOT OPEN To disconnect power from the mains, pull out the mains cord plug. When installing the
product, ensure that the plug is easily accessible.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING POWER: This DVD Recorder operates on a mains supply of 200-240V~, 50/60Hz.
TO QUALIFIED SERVICE PERSONNEL. WIRING: This DVD Player is supplied with a BSI 1363 approved 13 amp mains plug,
fused at 5 amp. When replacing the fuse always use a 5 amp BS 1362, BSI or ASTA
This lightning flash with arrowhead symbol within an equilateral triangle is approved type. Never use this plug with the fuse cover omitted. To obtain a replace-
intended to alert the user to the presence of uninsulated dangerous voltage ment fuse cover contact your dealer. If the type of plug supplied is not suitable for the
within the product’s enclosure that may be of sufficient magnitude to constitute mains sockets in your home, then the plug should be removed and a suitable type fit-
a risk of electric shock to persons. ted. Please refer to the wiring instructions below:
The exclamation point within an equilateral triangle is intended to alert the WARNING: A mains plug removed from the mains lead of this DVD Recorder must be
user to the presence of important operating and maintenance (servicing) destroyed. A mains plug with bared wires is hazardous if inserted in a mains socket.
instructions in the literature accompanying the product. Do not connect either wire to the earth pin, marked with the letter E or with the earth
symbol or coloured green or green and yellow. If any other plug is fitted, use a 5
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT amp fuse, either in the plug, or at the distribution board.
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. IMPORTANT: The wires in this mains lead are coloured in accordance with the follow-
WARNING: Do not install this equipment in a confined space such as a book case or ing codes:
similar unit. - BLUE: NEUTRAL, BROWN: LIVE - As the colours of the wires in the mains lead of
CAUTION: Do not block any ventilation openings. Install in accordance with the this DVD Recorder may not correspond with the coloured marking identifying the termi-
nals in your plug, proceed as follows: The wire which is coloured blue must be connect-
manufacturer's instructions. Slots and openings in the cabinet are provided for ed to the terminal which is marked with the letter N or coloured black. The wire which is
ventilation and to ensure reliable operation of the product and to protect it from over coloured brown must be connected to the terminal which is marked with the letter L or
heating. The openings should be never be blocked by placing the product on a bed, coloured red.
sofa, rug or other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided or the Disposal of your old appliance
manufacturer's instruction has been adhered to. 1. When this crossed-out wheeled bin symbol is attached to a product it
CAUTION: This product employs a Laser System. means the product is covered by the European Directive 2002/96/EC.
To ensure proper use of this product, please read this owner’s manual carefully and 2. All electrical and electronic products should be disposed of separately from
retain it for future reference. Should the unit require maintenance, contact an author- the municipal waste stream via designated collection facilities appointed by
ized service center. the government or the local authorities.
Use of controls, adjustments or the performance of procedures 3. The correct disposal of your old appliance will help prevent potential
other than those specified herein may result in hazardous radi- negative consequences for the environment and human health.
ation exposure. 4. For more detailed information about disposal of your old appliance, please
To prevent direct exposure to laser beam, do not try to open contact your city office, waste disposal service or the shop where you
the enclosure. Visible laser radiation when open. DO NOT purchased the product.
STARE INTO BEAM. This product is manufactured to comply with EMC Directive
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and 2004/108/EC and Low Voltage Directive 2006/95/EC.
no objects filled with liquids, such as vases, should be placed on the apparatus. European representative :
CAUTION concerning the Power Cord LG Electronics Service Europe B.V.
Most appliances recommend they be placed upon a dedicated circuit; Veluwezoom 15, 1327 AE Almere, The Netherlands
That is, a single outlet circuit which powers only that appliance and has no additional (Tel : +31–036–547–8940)
outlets or branch circuits. Check the specification page of this owner's manual to be
certain.Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall Manufactured under license from Dolby Laboratories. “Dolby” and the
outlets, extension cords, frayed power cords, or damaged or cracked wire insulation double-D symbol are trademarks of Dolby Laboratories.
are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates HDMI, the HDMI logo and High-Definition Multimedia Interface are
damage or deterioration, unplug it, discontinue use of the appliance, and have the trademarks or registered trademarks of HDMI licensing LLC.
cord replaced with an exact replacement part by an authorized service center.

2
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 3

About the Symbol Display

Safety Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
“ ” may appear on your TV display during operation and indicates that the
Types of Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
function explained in this owner’s manual is not available on that disc.
Hooking up the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Regional Codes
Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
This unit has a regional code printed on the rear of the unit. This unit can play
Contents Adjust the settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Displaying Disc Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
only DVD discs labeled same as the rear of the unit or “ALL”.
• Most DVD discs have a globe with one or more numbers in it clearly visible
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
on the cover. This number must match your unit’s regional code or the disc
Playing a DivX movie file . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
cannot play.
Listening to Music Disc or files . . . . . . . . . . . . . . . . . . . . . . . . .12
• If you try to play a DVD with a different regional code from your player, the
Viewing photo files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13
message “Check Regional Code” appears on the TV screen.
Using an USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Copyrights
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
It is forbidden by law to copy, broadcast, show, broadcast via cable, play in
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
public, or rent copyrighted material without permission. This product features
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
the copy protection function developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and playing the pictures of these
discs picture noise will appear. This product incorporates copyright protection
technology that is protected by method claims of certain U.S. patents and other
Types of Playable Discs intellectual property rights owned by Macrovision Corporation and other rights
Type Logo owners. Use of this copyright protection technology must be authorized by
Macrovision Corporation, and is intended for home and other limited viewing
DVD-VIDEO: Discs such as movies that can be uses only unless otherwise authorized by Macrovision Corporation. Reverse
purchased or rented. engineering or disassembly is prohibited.
DVD-R: Video mode and finalized only CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION
SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
DVD-RW: VR mode, Video mode and finalized only ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT
DVD+R: Video mode only THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT, PLEASE CONTACT
DVD+RW: Video mode only OUR CUSTOMER SERVICE CENTER.

Audio CD: Music CDs or CD-R/CD-RW in music CD

format that can be purchased.
This unit plays DVD±R/RW and CD-R/RW that contains audio titles, DivX, MP3,
WMA and/or JPEG files. Some DVD±RW/DVD±R or CD-RW/CD-R cannot be
played on this unit due to the recording quality or physical condition of the disc,
or the characteristics of the recording device and authoring software.

3
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 4

Hooking up the unit Hooking up the unit - more you can do

Audio and Video Connection A SCART Connection
The unit Audio/Video jacks are color coded (yellow for video, red for right audio Connect the TO TV jack on the unit and your TV using the SCART cable.
and white for left audio). If your TV has only one input for audio (mono), For SCART connections, resolution must be set to 576i(480i) by pressing
connect it to the left (white) audio jack on the unit. RESOLUTION button.
Caution : You must set the [TV Output Select] option to [RGB] on the setup
menu to use this connection. (See page 8)
B Component Video Connections
Connect the COMPONENT/PROGRESSIVE SCAN OUTPUT jacks on the
unit to the corresponding input jacks on your TV using a YPbPr cable.
• You will still need to connect the left and right audio cables to the TV, or
digital audio cable to your stereo.
Caution : You must set the [TV Output Select] option to [YPbPr] on the
setup menu to use this connection. (See page 8)
Resolution Setting
• You can change the resolution for component video output. Press
RESOLUTION repeatedly to select the desired resolution - 576i(480i),
576p(480p), 720p, 1080i, 1080p.
• For 720p and 1080p resolution on the component video output, only
non-copy protected discs can be played back. If the disc is copy
proteced,it will be displayed at the 576p(480p) resolution.
• Depending on your TV, some of the resolution settings may result in the
picture disappearing or an abnormal picture appearing. In this case, press
RESOLUTION repeatedly unit the picture re-appears.

C Digital Audio Output Connection

Connect the AC C B C A Connect one of the unit’s DIGITAL AUDIO OUTPUT (COAXIAL or OPTICAL)
power cord into the jacks to the corresponding jack on your amplifier.
power outlet. • If the audio format of the digital output does not match the capabilities of
your amplifier, the amplifier will produce a strong, distorted sound or no
sound at all.
• To see the audio format of the current disc in the on-screen display, press
AUDIO.
• This unit does not perform internal (2 channel) decoding of a DTS sound
track. To enjoy DTS multi channel surround, you must connect this unit to
a DTS compatible amplifier via one of this unit’s digital audio outputs.

4
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 5

Hooking up the unit About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a
HDMI Connection single digital connection for use with DVD Players, Set-Top Boxes, and other AV
Connect the HDMI OUTPUT jack on the unit to the HDMI input jack on an devices. HDMI was developed to provide the technologies of HDCP (High-band-
HDMI compatible TV using an HDMI cable. width Digital Content Protection). HDCP is used to protect digital content
transmitted and received.
HDMI has the capability to support standard, enhanced or high-definition video
plus standard to multi-channel surround-sound audio, HDMI features include
uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one
connector (instead of several cables and connectors), and communication
between the AV source and AV devices such as DTVs.

Notes on HDMI connection

• If your TV is not capable of handling 96 kHz sampling frequency, set the
[Sampling Freq.] option to [48 kHz] on the setup menu (See page 8).
• If your TV is not equipped with Dolby Digital and MPEG decoder,
set the [Dolby Digital] and [MPEG] options to [PCM] on the setup menu (See
page 8).
• Depending on your TV, some of the resolution settings may result in the
picture disappearing or an abnormal picture appearing. In this case, press
RESOLUTION repeatedly unit the picture re-appears.
• Changing the resolution when the unit is connected with HDMI connector
may result in malfunctions. To solve the problem, turn off the unit and then
turn it on again.
• When you connect a HDMI or DVI compatible device make sure of the
following:
- Try switching off the HDMI/DVI device and this unit. Next, switch on the
HDMI/DVI device and leave it for around 30 seconds, then switch on this
unit.
- The connected device’s video input is set correctly for this unit.
Hooking up the unit - more you can do - The connected device is compatible with 720(1440)X576i(480i),
720X576p(480p), 1280X720p, 1920X1080i or 1920X1080p video input.
Resolution Setting
- The 1080p, 720p and 480p resolutions are the progressive scan applied
You can change the resolution for HDMI output. Press RESOLUTION repeatedly resolution
to select the desired resolution - 576i(480i), 576p(480p), 720p, 1080i, 1080p. • Not all HDCP-compatible DVI devices will work with this unit.
- The picture will not be displayed properly with non-HDCP device.
Note for 1080p resolution
The unit is able to provide a 1080p full HD image to most 1080p-capable TVs in
the market today. However, there are some 1080p TVs available from certain
companies that are limited in the types of 1080p images that can be accepted.
Specifically, 1080p-capable TVs that don’t accept images in 60Hz can’t display
an image from this unit.

5
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 6

Remote control







a






REPEAT : Repeats a chapter, track, title or all.
A-B : Repeats a section.
POWER (1) : Switches the unit ON or OFF.
RESOLUTION : Sets the output resolution for HDMI
OPEN/CLOSE (Z) : Opens and closes the disc tray.
Numerical buttons: Selects numbered items in a jack.
menu. : This button is not available.
CLEAR : Removes a track number on the Program Controlling other TV’s with the remote control
List or a mark on the Marker Search menu.
a TV : TV control buttons.
You can control the sound level, input source, and
power switch of your LG TV with the supplied remote
control. While holding down TV POWER button,







b







press the number buttons to select the manufacturer
SCAN (m / M) : Search backward or forward. code for your TV (see the table below). Release TV
SKIP (. / >) : Go to next or previous POWER button.
chapter/track.
PAUSE/STEP (X) : Pauses playback Code numbers of controllable TVs
temporarily/press repeatedly for frame-by-frame If more than one code number is listed, try entering
b playback. them one at a time until you find the one that works
PLAY (N) : Starts playback. with your TV. Depending on your TV, some or all
STOP (x) : Stops playback. buttons may not function on the TV, ever after
entering the correct manufacturer code.







c







DVD MENU : Access the DVD menu. Manufacturer Code Number
TITLE : Access the disc’s title menu, if available.
LG/GoldStar 1 (Default), 2
c vV b B : Navigates the menus.
Zenith 1, 3, 4
ENTER ( ) : Confirms menu selection.
DISPLAY : Accesses On-Screen Display. Samsung 6, 7
RETURN (O) : Press to move backwards in the Sony 8, 9
menu or exit the menu. Change the USB mode.
Hitachi 4
AUDIO ( ) : Selects an audio language or audio
channel.
Put the battery into the Remote Control
SUBTITLE ( ) : Selects a subtitle language.
ANGLE ( ) : Selects a DVD camera angle, if Remove the battery cover on the rear of Remote
d available. Control, and insert battery (size AAA) with + and –
SETUP : Accesses or exits the setup menu. matched correctly.

d







MARKER : Marks any point during playback.
SEARCH : Displays MARKER SEARCH menu.
PROGRAM : Enters the program edit mode.
ZOOM : Enlarges video image.

6
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 7

Main Unit
DVX382H
a b c d e f g

DVX392H
a b c d e f g

a 1/I (Power) f USB Port

Turn the unit ON or OFF. Connect an USB Flash Drive.

b Disc Tray g • N (Play)

Insert a disc here. Starts playback.

c Z (Open / Close) • x (Stop)

Stops playback.
Opens or closes the disc tray.
• . (Skip)
d Display window Returns to the beginning of current chapter or track or go to
Shows the current status of the unit. the previous chapter or track.
e Remote sensor • > (Skip)
Point the remote control here. Go to next chapter or track.

7
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 8

Display Mode – If you selected 4:3, you’ll need to define how you would like
Adjust the settings widescreen programs and films to be displayed on your TV screen.
ON REMOTE [Letterbox]: This displays a widescreen picture with black bands at the top
and bottom of the screen.
1 Display setup menu: SETUP [Panscan]: This fills the entire 4:3 screen, cropping the picture as necessary.
2 Select a desired option on the first level: vV TV Output Select – Select an option according to the TV connection type.
3 Move to second level: B [RGB]: When your TV is connected with the SCART jack.
[YPbPr]: When your TV is connected with the COMPONENT/PROGRESSIVE
4 Select a desired option on the second level: vV
SCAN OUTPUT jacks on the unit.
5 Move to third level: B
Adjust the audio settings
6 Change the setting: v V / ENTER
Dolby Digital / DTS / MPEG – Selects the type of digital audio signal when
using the DIGITAL AUDIO OUTPUT jack.
[Bitstream]: Select this when you connect this unit’s DIGITAL AUDIO
Adjust the settings - more you can do OUTPUT jack to an amplifier with a built-in Dolby Digital, DTS or MPEG
When you turn on for the first time decoder.
[PCM] (for Dolby Digital / MPEG): Select this when you connect this unit’s
The menu for a language selection will appear when you turn on the unit for the
DIGITAL AUDIO OUTPUT jack to an amplifier without a built-in Dolby Digital
first time. You must select a language to use the unit. Use vV b B to select a
or MPEG decoder.
language then press ENTER and the confirm menu will appear. Use b B to [Off] (for DTS): Select this when you connect this unit’s DIGITAL AUDIO
select [Enter] then press ENTER. OUTPUT jack to an amplifier without a built-in DTS decoder.
Adjust the language settings Sample Freq. (Frequency) – Selects the sampling frequency of the audio
Menu Language – Select a language for the Setup menu and on-screen signal.
display. [48 KHz]: The audio signals are always converted to 48 kHz.
Disc Audio/Subtitle/Menu – Select a language for the Disc Audio/Subtitle/ [96 KHz]: The audio signals are output in their original format.
Menu. DRC (Dynamic Range Control) – Make the sound clear when the volume is
[Original]: Refers to the original language in which the disc was recorded. turned down (Dolby Digital only). Set to [On] for this effect.
[Other]: To select another language, press number buttons then ENTER to Vocal – Set to [On] only when a multi-channel karaoke DVD is playing.
enter the corresponding 4-digit number according to the language code list. The karaoke channels on the disc mix into normal stereo sound.
(see page 14) If you make a mistake while entering number, press CLEAR to
delete numbers then correct it.
[Off] (for Disc Subtitle): Turn off Subtitle.
Adjust the display settings
TV Aspect – Select which screen aspect to use based on the shape of your TV
screen.
[4:3]: Select when a standard 4:3 TV is connected.
[16:9]: Select when a 16:9 wide TV is connected.

8
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 9

Adjust the lock settings Displaying Disc Information

You must set the [Area Code] option to use the lock options. Select [Area Code]
option then press B. Enter a 4-digit password then press ENTER. Enter it again ON REMOTE
then press ENTER to verify. If you make a mistake while entering number, 1 Press DISPLAY: DISPLAY
press CLEAR then correct it.
If you forget your password you can reset it. Display setup menu then input the 2 Select a item: vV
6-digit number “210499”. The “P CLr” appear in the display window and the 3 Adjust the Display menu settings: b B / ENTER
password is deleted. 4 To return the exit: DISPLAY
Rating – Select a rating level. The lower the level, the stricter the rating. Select
[Unlock] to deactivate the rating.
Password – Sets or changes the password for lock settings. Displaying Disc Information - more you can do
[New]: Enter a new 4-digits password using the numerical buttons then press
ENTER. Enter the password again to confirm. You can select an item by pressing vV and change or select the setting by
[Change]: Enter the new password twice after entering the current password. pressing b B.

Area Code – Select a code for a geographic area as the playback rating level. Current title (or track) number/total number of titles (or tracks)
This determines which area’s standards are used to rate DVDs controlled by the Current chapter number/total number of chapters
parental lock. (See page 14) Elapsed playing time
Adjust the others settings Selected audio language or channel
B.L.E. (Black Level Expansion) – To select the black level of playback Selected subtitle
pictures. Set your preference and monitor’s ability.
Selected angle/total number of angles
DivX(R) VOD – We provide you with the DivX® VOD (Video On Demand)
registration code that allows you to rent and purchase videos using the DivX®
VOD service. For more information, visit www.divx.com/vod. Symbol Used in this Manual
Press ENTER when [Select] icon is highlighted and you can view the
registration code of the unit. All the downloaded videos from DivX® VOD can ALL All discs and file listed below ACD Audio CDs
only be played back on this unit.
DVD DVD and finalized DVD±R/RW CD-G CD-G discs
MP3 MP3 files DivX DivX files
WMA WMA files

9
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 10

Pause a playback ALL

Playing a Disc Press PAUSE/STEP (X) to pause playback. Press PLAY ( N) to continue
ON REMOTE playback.

1 Open the disc tray: Z OPEN/CLOSE Frame-by-Frame playback DVD DivX

2 Insert a Disc: - Press PAUSE/STEP (X) repeatedly to play Frame-by-Frame playback.

3 Close the disc tray: Z OPEN/CLOSE Playing repeatedly ALL
4 Start playback: N PLAY Press REPEAT repeatedly to select an item to be repeated. The current title,
5 To stop playback: x STOP chapter or track will be played back repeatedly. To return to normal playback,
press REPEAT repeatedly to select [Off].

Fast forward or fast reverse

Playing a Disc - more you can do DVD DivX ACD WMA MP3
Press SCAN (m or M) to play fast forward or fast reverse during playback.
Stops the playback
You can change the various playback speed by pressing SCAN (m or M)
The unit records the stopped point depending on the disc. “ Xx x ” appears on repeatedly. Press PLAY ( N) to continue play at normal speed.
the screen briefly. Press PLAY ( N) to resume playback (from the scene
point). If you press STOP (x x ) again or unload the disc (“ x ” appears on the Repeating a specific portion (A-B) DVD DivX ACD
screen), the unit will clear the stopped point. Press A-B at the beginning of the portion you wish to repeat and again at the
Xx =Resume Stop, x =Complete Stop)
(X end of the portion. Your selected portion will be repeated continually.
The resume point may be cleared when a button is pressed (for example To return to normal playback, press A-B to select [Off].
:POWER, OPEN/CLOSE, etc).
Selecting a subtitle language DVD DivX
Playing a DVD that has a menu DVD
During playback, press SUBTITLE ( ) repeatedly to select a desired subtitle
Most DVD now have menus which load first before the film begins to play. You language.
can navigate these menus using vV b B or number button to highlight an
option. Press ENTER to select. Watching from a different angle DVD

Playing a DVD VR disc If the angle indicator appears on the screen for a moment, you can select a
different camera angle by pressing ANGLE ( ) repeatedly.
This unit will play DVD-RW disc that is recorded using the Video Recording
(VR) format. When you insert a disc DVD VR disc, the menu will appear on the Hearing a different audio DVD DivX CD-G
screen. Use vV to select a title then press PLAY ( N). To display DVD-VR During playback, press AUDIO ( ) repeatedly to switch between the available
menu, press DVD MENU or TITLE.
audio languages, channels or encoding methods.
Some DVD-VR disc are made with CPRM data by DVD RECORDER. Player
does not support these kinds of discs. Slow down the playing speed DivX (Forward only) DVD

Skip to the next/previous chapter/track ALL While playback is paused, press SCAN (m or M) to slow down reverse or
forward playback. You can change the various playback speed by pressing
Press SKIP (>) to move to the next chapter/track.
SCAN (m or M) repeatedly. Press PLAY ( N) to continue play at normal
Press SKIP (.) to return to the beginning of the current chapter/track.
speed.
Press SKIP (.) twice briefly to step back to the previous chapter/track.

10
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 11

Watching a enlarged video image DVD DivX

During playback or pause mode, press ZOOM repeatedly to select zoom mode. You
Playing a DivX movie file
can move through the zoomed picture using vVb B buttons. Press CLEAR to exit. ON REMOTE
Viewing the title menu DVD 1 Open the disc tray: Z OPEN/CLOSE
Press TITLE to display the disc's title menu, if available. 2 Insert a disc: -
Viewing the DVD menu DVD 3 Close the disc tray: Z OPEN/CLOSE
Press DVD MENU to display the disc menu, if available. 4 Select a movie file from the menu: v V, DVD MENU
5 Start playback: N PLAY
Marking a favorite scene DVD DivX
You can mark positions by pressing MARKER at the desired position up to 9 6 To stop playback: x STOP
markers. Also you can recall or clear positions by pressing SEARCH.
Use b or B to select a desired marker on the [MARKER SEARCH] menu, then press
ENTER to recall it or CLEAR to clear it. Playing a DivX movie file - more you can do
Starting play from selected time DVD DivX Changing the character set to display DivX® subtitle correctly
Searches for the starting point of entered time code. Press DISPLAY then select Press and hold SUBTITLE for 3 seconds during playback. The language code
clock icon. Enter a time then press ENTER. For example, to find a scene at 1 hours, will appear. Press b B to select another language code until the subtitle is
10 minutes, and 20 seconds, enter "11020" and press ENTER. If you enter the wrong displayed properly and then press ENTER.
number, press CLEAR to enter again.
DivX file requirement
Last Scene Memory DVD ACD
DivX file compatibility with this player is limited as follows:
This unit memorizes last scene from the last disc that is viewed. The last scene • Available resolution size: 720x576 (W x H) pixel.
remains in memory even if you remove the disc from the player or switch off the unit. • The file names of DivX and subtitle are limited to 56 characters.
If you load a disc that has the scene memorized, the scene is automatically recalled. • DivX file extensions: “.avi”, “.mpg”, “.mpeg”
• Playable DivX subtitle: SubRip (.srt / .txt), SAMI (.smi),
Screen Saver SubStation Alpha(.ssa/.txt), MicroDVD (.sub/.txt),
The screen saver appears when you leave the unit in Stop mode for about five SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD Subtitle System (.txt),
minutes. If the Screen Saver is displayed for five minutes, the unit automatically turns VobSub(*.sub) Sub/idx, stream based format
itself off. • Playable Codec format: “DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “MP43”,
“3IVX”, “XviD”
System Select • Only the playback function is supported with DivX 6.0 in the unit.
You must select the appropriate system mode for your TV system. Remove any disc • Playable Audio format: “Dolby Digital”, “DTS”, “PCM”, “MP3”, “WMA”
that might be in the unit, press and hold PAUSE/STEP (X) for more than five • Sampling frequency: within 8 - 48 kHz (MP3), within 22 - 48 kHz (WMA)
seconds to be able to select a system (PAL, NTSC). • Bit rate: within 8 - 320 kbps (MP3), within 32 - 256 kbps (WMA),
less than 8Mbps (DivX file)
Mixed disc or USB Flash Drive – DivX, MP3/WMA and JPEG • CD-R/RW, DVD±R/RW Format: ISO 9660
When playing a disc or USB Flash Drive contained with DivX, MP3/WMA and JPEG • Maximum Files/Disc: Less than 650 (total number of files and folders)
files together, you can select which menu of files you would like to play by pressing
TITLE.

11
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 12

• Bit rate: within 8 - 320kbps (MP3), within 32 - 256kbps (WMA)

Listening to Music Disc or files • CD-R/RW, DVD±R/RW Format: ISO 9660
• Maximum Files/Disc: Less than 650 (total number of files and folders)
ON REMOTE
1 Open the disc tray: Z OPEN/CLOSE Viewing photo files
2 Insert a disc: -
ON REMOTE
3 Close the disc tray: Z OPEN/CLOSE
1 Open the disc tray: Z OPEN/CLOSE
4 Select a music from the menu: v V, DVD MENU
2 Insert a disc: -
5 Start playback: N PLAY
3 Close the disc tray: Z OPEN/CLOSE
6 To stop playback: x STOP
4 Select a photo file on the menu: v V, DVD MENU
5 Display the selected file in full screen: N PLAY
Listening to Music Disc or files - more you 6 To return to the menu: x STOP
can do
Creating your own program Viewing photo files - more you can do
You can play the contents of a disc in the order you want by arranging the order
of the musics on the disc. To add a music(s) on the program list, press Viewing photo files as a slide show
PROGRAM to enter the program edit mode ( E mark appears on the menu). Use vV b B to highlight ( ) icon then press ENTER to start slide show.
Select a desired music on the [List] then press ENTER to add the music to the You can change slide show speed using b B when ( ) icon is highlighted.
program list. Select a music from the program list then press ENTER to start
programmed playback. To clear a music from the program list, select the music Skip to the next/previous photo
you want to clear then press CLEAR in program edit mode. To clear all music Press SKIP (. or >) to view the previous/next photo.
from the program list, select [Clear All] then press ENTER in program edit mode.
The program is cleared when the disc is removed or the unit is turned off. Rotate a photo
Playing an CD-G disc Use vV to rotate the photo in full screen counterclockwise or clockwise while
Once you insert an CD-G disc, a menu appears on the screen. Use vV to viewing a photo in full screen.
select a track then press PLAY ( N). To display the CD-G menu during Pause a slide show
playback, press STOP (x x ) twice.
You can display the setup menu by pressing SETUP only when CD-G menu Press PAUSE/STEP (X) to pause a slide show. Press PLAY ( N) to continue
appears on the TV screen. the slide show.

Displaying file information (ID3 TAG) Listening to music during slide show
While playing a MP3 file containing file information, you can display the You can listen to music during slide show, if the disc contain music and photo
information by pressing DISPLAY repeatedly. files together. Use vV b B to highlight ( ) icon then press ENTER to start
slide show.
MP3/WMA music file requirement
Watching a enlarged photo image
MP3/WMA compatibility with this unit is limited as follows:
• File extensions: “.mp3”, “.wma” While viewing a photo in full screen, press ZOOM repeatedly to select zoom
• Sampling frequency: within 8 - 48 kHz (MP3), within 22 - 48kHz (WMA) mode. You can move through the zoomed photo using vVb B buttons. Press
CLEAR to exit.
12
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 13

Photo file requirement

JPEG file compatibility with this unit is limited as follows:
• File extensions: “.jpg”
• Photo size: Less than 5MB recommended
• CD-R/RW, DVD±R/RW Format: ISO 9660
• Maximum Files/Disc: Less than 650 (total number of files and folders)

Using an USB Flash Drive

You can play MP3/WMA/JPEG/DivX files in the USB Flash Drive with
version 1.1.

ON REMOTE
1 Connect an USB Flash Drive to the USB -
port on the unit:
2 Display the menu screen in stop mode: O RETURN
3 Select a file: v V, DVD MENU
4 Play the file: N PLAY
5 Remove the USB Flash Drive: -

Notes an USB Flash Drive

• You can switch USB and DISC mode by pressing RETURN (O) only in stop
mode.
• Do not extract the USB device in operating.
• Aback up demands to prevent a data damage.
• If you use a USB extension cable or USB HUB, the USB device might not be
recognized.
• Music files (MP3/WMA), photo files (JPEG) and DivX files can be played.
For details of operations on each files, refer to relevant pages.
• This unit is not supported when the total number of files is more than 650.
• The USB function of this unit does not support all kinds of USB devices.
• Digital camera and mobile phone are not supported.

13
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 14

Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.
Language Code Language Code Language Code Language Code Language Code Language Code
Afar 6565 Croatian 7282 Hausa 7265 Lingala 7678 Quechua 8185 Tajik 8471
Afrikaans 6570 Czech 6783 Hebrew 7387 Lithuanian 7684 Rhaeto-Romance 8277 Tamil 8465
Albanian 8381 Danish 6865 Hindi 7273 Macedonian 7775 Rumanian 8279 Telugu 8469
Ameharic 6577 Dutch 7876 Hungarian 7285 Malagasy 7771 Russian 8285 Thai 8472
Arabic 6582 English 6978 Icelandic 7383 Malay 7783 Samoan 8377 Tonga 8479
Armenian 7289 Esperanto 6979 Indonesian 7378 Malayalam 7776 Sanskrit 8365 Turkish 8482
Assamese 6583 Estonian 6984 Interlingua 7365 Maori 7773 Scots Gaelic 7168 Turkmen 8475
Aymara 6588 Faroese 7079 Irish 7165 Marathi 7782 Serbian 8382 Twi 8487
Azerbaijani 6590 Fiji 7074 Italian 7384 Moldavian 7779 Serbo-Croatian 8372 Ukrainian 8575
Bashkir 6665 Finnish 7073 Javanese 7487 Mongolian 7778 Shona 8378 Urdu 8582
Basque 6985 French 7082 Kannada 7578 Nauru 7865 Sindhi 8368 Uzbek 8590
Bengali; Bangla 6678 Frisian 7089 Kashmiri 7583 Nepali 7869 Singhalese 8373 Vietnamese 8673
Bhutani 6890 Galician 7176 Kazakh 7575 Norwegian 7879 Slovak 8375 Volapük 8679
Bihari 6672 Georgian 7565 Kirghiz 7589 Oriya 7982 Slovenian 8376 Welsh 6789
Breton 6682 German 6869 Korean 7579 Panjabi 8065 Spanish 6983 Wolof 8779
Bulgarian 6671 Greek 6976 Kurdish 7585 Pashto, Pushto 8083 Sudanese 8385 Xhosa 8872
Burmese 7789 Greenlandic 7576 Laothian 7679 Persian 7065 Swahili 8387 Yiddish 7473
Byelorussian 6669 Guarani 7178 Latin 7665 Polish 8076 Swedish 8386 Yoruba 8979
Chinese 9072 Gujarati 7185 Latvian, Lettish 7686 Portuguese 8084 Tagalog 8476 Zulu 9085

Area Codes
Choose a area code from this list.
Area Code Area Code Area Code Area Code Area Code Area Code
Afghanistan AF Costa Rica CR Greenland GL Maldives MV Paraguay PY Sri Lanka LK
Argentina AR Croatia HR Hong Kong HK Mexico MX Philippines PH Sweden SE
Australia AU Czech Republic CZ Hungary HU Monaco MC Poland PL Switzerland CH
Austria AT Denmark DK India IN Mongolia MN Portugal PT Taiwan TW
Belgium BE Ecuador EC Indonesia ID Morocco MA Romania RO Thailand TH
Bhutan BT Egypt EG Israel IL Nepal NP Russian Federation RU Turkey TR
Bolivia BO El Salvador SV Italy IT Netherlands NL Saudi Arabia SA Uganda UG
Brazil BR Ethiopia ET Jamaica JM Netherlands Antilles AN Senegal SN Ukraine UA
Cambodia KH Fiji FJ Japan JP New Zealand NZ Singapore SG United States US
Canada CA Finland FI Kenya KE Nigeria NG Slovak Republic SK Uruguay UY
Chile CL France FR Kuwait KW Norway NO Slovenia SI Uzbekistan UZ
China CN Germany DE Libya LY Oman OM South Africa ZA Vietnam VN
Colombia CO Great Britain GB Luxembourg LU Pakistan PK South Korea KR Zimbabwe ZW
Congo CG Greece GR Malaysia MY Panama PA Spain ES

14
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 15

Troubleshooting Specifications
Symptom Cause Correction General
No power. The power cord is disconnected. Plug the power cord into the wall Power requirements AC 200-240 V, 50/60 Hz
outlet securely. Power consumption 9W
Dimensions (Approx.) 430 x 35 x 200 mm
The power is on, No disc is inserted. Insert a disc. (W x H x D) without foot
but the unit does Net Weight (Approx.) 1.5 kg
not work. Operating temperature 5 °C to 35 °C
Operating humidity 5 % to 90 %
No picture. The TV is not set to receive the Select the appropriate video input Laser Semiconductor laser
signal from the unit. mode on the TV. Signal system PAL / NTSC

The video cable is not connected Connect the video cable securely. Outputs
securely.
Video Output 1.0 V (p-p), 75 Ω, sync negative,
No sound. The equipment connected with Select the correct input mode of RCA jack (L, R) x 1 /
the audio cable is not set to the audio amplifier. SCART (TO TV)
receive the signal from the unit. Component Video Output (Y) 1.0 V (p-p), 75 Ω, sync negative,
RCA jack x 1
The AUDIO options are set to the Set the AUDIO settings to the (Pb)/(Pr) 0.7 V (p-p), 75 Ω,
wrong position. correct position. RCA jack x 2
HDMI Video/Audio Output 19 pin(HDMI standard, Type A)
The unit does not An unplayable disc is inserted. Insert a playable disc. (Check the Audio Output 2.0 Vrms (1 KHz, 0 dB), 600 Ω,
start playback. disc type and regional code.) RCA jack (L, R) x 1 /
SCART (TO TV)
The rating level is set. Change the rating level. Digital Output (Coaxial) 0.5 V (p-p), 75 Ω, RCA jack x 1
Digital Output (Optical) 3V (p-p), Optical X 1
The remote con- The remote control is not pointed Point the remote control at the
trol does not work at the remote sensor on the unit. remote sensor of the unit.
Accessories
properly.
The remote control is too far from Operate the remote control closer Video/Audio cable, Remote Control, Battery
the unit. to the unit.

Designs and specifications are subject to change without

prior notice.

15
DV382H.392H-E.BGBRLLK_2723_ENG 6/13/08 9:16 AM Page 16

Technology with the human touch

GUARANTEE
● LG Electronics U.K. Ltd. will provide the following services in order to expedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a period of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the repair of this LG equipment, for a period of 12
months from the original date of purchase. These claims must be made in accordance with the published scale of service charges and
relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made to the apparatus, or if non standard components
are used or if the serial number of the
apparatus is removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was originally purchased. The dealer may, before carrying
out service under guarantee, require a receipted account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become exhausted or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
● REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED AT THE TIME GUARANTEE SER-
VICE IS PROVED.
● Product Registration Card : It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
● To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
MODEL NO.* SERIAL NO.* DATE OF PURCHASE.*

* Please complete for your own record

In all cases of difficulty - consult your LG dealer

from whom the product was purchased

LGEUK Website : www.lge.co.uk

( service website : www.lgelectronics.co.uk )